NixieTubeClock/Nixie_Firmware_Rust/src/main.rs

#![cfg_attr(test, allow(unused_imports))]
#![cfg_attr(not(test), no_std)]
#![cfg_attr(not(test), no_main)]
#![feature(half_open_range_patterns)]
#![feature(exclusive_range_pattern)]
#![allow(dead_code)]

// custom panic handler
#[cfg(not(test))]
use core::panic::PanicInfo;

use core::{cell::RefCell, ops::DerefMut};
use cortex_m::{interrupt::free, interrupt::Mutex, peripheral::NVIC};
use cortex_m_rt::entry;
use stm32l4xx_hal::{
    delay::Delay,
    device::{I2C1, TIM2},
    gpio::{
        Alternate, Edge, Floating, Input, OpenDrain, Output, PullUp, PushPull, AF4, PA3, PB5, PC15,
    },
    gpio::{State, PA10, PA9},
    i2c::I2c,
    interrupt, pac,
    prelude::*,
    rcc,
    stm32::Interrupt,
    timer::Timer,
};

mod ds3231;
mod nixie;
mod pca9685;
mod tusb322;

use nixie::*;

static RTC_INT: Mutex<RefCell<Option<PB5<Input<Floating>>>>> = Mutex::new(RefCell::new(None));
static FAULT_INT: Mutex<RefCell<Option<PA3<Input<PullUp>>>>> = Mutex::new(RefCell::new(None));
static FAULT_LED: Mutex<RefCell<Option<PC15<Output<PushPull>>>>> = Mutex::new(RefCell::new(None));
static I2C: Mutex<
    RefCell<
        Option<
            I2c<
                I2C1,
                (
                    PA9<Alternate<AF4, Output<OpenDrain>>>,
                    PA10<Alternate<AF4, Output<OpenDrain>>>,
                ),
            >,
        >,
    >,
> = Mutex::new(RefCell::new(None));
static REFRESH_TIMER: Mutex<RefCell<Option<Timer<TIM2>>>> = Mutex::new(RefCell::new(None));

// unsafe fn any_as_u8_slice<T: Sized>(p: &T) -> &[u8] {
//     core::slice::from_raw_parts(
//         (p as *const T) as *const u8,
//         core::mem::size_of::<T>(),
//     )
// }

// pub fn concat<T: Copy + Default, const A: usize, const B: usize>(a: &[T; A], b: &[T; B]) -> [T; A+B] {
//     let mut whole: [T; A+B] = [Default::default(); A+B];
//     let (one, two) = whole.split_at_mut(A);
//     one.copy_from_slice(a);
//     two.copy_from_slice(b);
//     whole
// }

#[cfg(not(test))]
#[entry]
fn main() -> ! {
    // Acquire a singleton instance for the chip's peripherals
    let mut dp = pac::Peripherals::take().unwrap();
    let cp = pac::CorePeripherals::take().unwrap();

    // Consume the raw peripheral and return a new object that implements a higher level API
    let mut flash = dp.FLASH.constrain();
    let mut rcc = dp.RCC.constrain();
    let mut pwr = dp.PWR.constrain(&mut rcc.apb1r1);

    // Configure clocks to run at maximum frequency off internal oscillator
    let clocks = rcc
        .cfgr
        .pll_source(rcc::PllSource::HSI16)
        .sysclk(64.mhz())
        .hclk(64.mhz())
        .pclk1(64.mhz())
        .pclk2(64.mhz())
        .freeze(&mut flash.acr, &mut pwr);

    // Configure delay timer that operates off systick timer
    let mut delay_timer = Delay::new(cp.SYST, clocks);

    // Split GPIO peripheral into independent pins and registers
    let mut gpioa = dp.GPIOA.split(&mut rcc.ahb2);
    let mut gpiob = dp.GPIOB.split(&mut rcc.ahb2);
    let mut gpioc = dp.GPIOC.split(&mut rcc.ahb2);

    // Configure high voltage PSU enable pin on PA2
    let mut hv_enable =
        gpioa
            .pa2
            .into_push_pull_output_with_state(&mut gpioa.moder, &mut gpioa.otyper, State::Low);

    // Configure fault LED output on PC15
    let fault_led = gpioc.pc15.into_push_pull_output_with_state(
        &mut gpioc.moder,
        &mut gpioc.otyper,
        State::Low,
    );

    // Store fault LED in static singleton so that interrupt has access to it
    free(|cs| {
        FAULT_LED.borrow(cs).replace(Some(fault_led));
    });

    // Configure fault input interrupt on PA3
    let mut fault_int = gpioa
        .pa3
        .into_pull_up_input(&mut gpioa.moder, &mut gpioa.pupdr);
    fault_int.make_interrupt_source(&mut dp.SYSCFG, &mut rcc.apb2);
    fault_int.enable_interrupt(&mut dp.EXTI);
    fault_int.trigger_on_edge(&mut dp.EXTI, Edge::FALLING);

    // Sanity check that fault pin isn't already set (active low) before enabling interrupt
    if fault_int.is_high().unwrap() {
        // Configure NVIC mask to enable interrupt source
        unsafe {
            NVIC::unmask(Interrupt::EXTI3);
        }

        // Store fault interrupt in static singleton so that interrupt has access to it
        free(|cs| {
            FAULT_INT.borrow(cs).replace(Some(fault_int));
        });
    } else {
        panic!();
    }

    // Configure I2C SCL
    let scl = gpioa
        .pa9
        .into_open_drain_output(&mut gpioa.moder, &mut gpioa.otyper);
    let scl = scl.into_af4(&mut gpioa.moder, &mut gpioa.afrh);

    // Configure I2C SDA
    let sda = gpioa
        .pa10
        .into_open_drain_output(&mut gpioa.moder, &mut gpioa.otyper);
    let sda = sda.into_af4(&mut gpioa.moder, &mut gpioa.afrh);

    // Initialize I2C (configured for 1Mhz, but actually runs at 600kHz)
    let mut i2c = I2c::i2c1(dp.I2C1, (scl, sda), 1.mhz(), clocks, &mut rcc.apb1r1);

    // Initialize TUSB322 (USB Type-C configuration chip)
    tusb322::init(TUSB322_ADDR, &mut i2c);

    // Initialize DS3231 (RTC)
    ds3231::init(DS3231_ADDR, &mut i2c);

    // Configure input interrupt pin from DS3231 on PB5
    // Interrupt is pulled high, with open drain on DS3231 to pull low
    let mut rtc_int = gpiob
        .pb5
        .into_floating_input(&mut gpiob.moder, &mut gpiob.pupdr);
    rtc_int.make_interrupt_source(&mut dp.SYSCFG, &mut rcc.apb2);
    rtc_int.enable_interrupt(&mut dp.EXTI);
    rtc_int.trigger_on_edge(&mut dp.EXTI, Edge::FALLING);

    // Configure NVIC mask to enable interrupt source
    unsafe {
        NVIC::unmask(Interrupt::EXTI9_5);
    }

    // Store RTC interrupt in static singleton so that interrupt has access to it
    free(|cs| {
        RTC_INT.borrow(cs).replace(Some(rtc_int));
    });

    // Configure DAC AMP enable pin for AD8591 on PB1
    let mut _dac_enable = gpiob.pb1.into_push_pull_output_with_state(
        &mut gpiob.moder,
        &mut gpiob.otyper,
        State::High,
    );

    // Configure DAC VIN for AD8591 on PA5
    // Note that this pin should actually be configured as analog output (for DAC)
    // but stm32l4xx_hal doesn't have support for the DAC as of now. We also currently
    // set the output to only the highest possible voltage, so the same functionality
    // can be achieved by configuring the pin as a digital output set to high.
    let mut _dac_output = gpioa.pa5.into_push_pull_output_with_state(
        &mut gpioa.moder,
        &mut gpioa.otyper,
        State::High,
    );

    // Configure PWM enable pin (active low) for PCA9685 on PA7
    let mut pwm_enable = gpioa.pa7.into_push_pull_output_with_state(
        &mut gpioa.moder,
        &mut gpioa.otyper,
        State::High,
    );

    // Initialize the PCA9685 display refresh timer
    let refresh_timer = Timer::tim2(
        dp.TIM2,
        nixie::REFRESH_RATE_HZ.hz(),
        clocks,
        &mut rcc.apb1r1,
    );

    // Configure NVIC mask to enable interrupt for TIM2
    unsafe { NVIC::unmask(Interrupt::TIM2) };

    // Save display refresh timer in static singleton so that interrupt has access to it
    free(|cs| {
        REFRESH_TIMER.borrow(cs).replace(Some(refresh_timer));
    });

    // Small delay to ensure that PCA9685 is fully powered on before writing to it
    delay_timer.delay_us(10_u32);

    // Initialize PCA9685 (PWM driver)
    pca9685::init(PCA9685_ALL_CALL, &mut i2c);

    // Enable PWM output after PCA9685 has been initialized
    pwm_enable.set_low().unwrap();

    // Store I2C peripheral in global static variable as it is used in interrupt
    free(|cs| {
        I2C.borrow(cs).replace(Some(i2c));
    });

    // Enable the high voltage power supply last
    hv_enable.set_high().unwrap();

    loop {}
}

fn set_fault_led(state: State) {
    free(|cs| {
        let mut led_ref = FAULT_LED.borrow(cs).borrow_mut();
        if let Some(ref mut led) = led_ref.deref_mut() {
            match state {
                State::High => led.set_high().unwrap(),
                State::Low => led.set_low().unwrap(),
            };
        }
    });
}

#[interrupt]
fn EXTI9_5() {
    free(|cs| {
        let mut rtc_int_ref = RTC_INT.borrow(cs).borrow_mut();
        let mut i2c_int_ref = I2C.borrow(cs).borrow_mut();
        if let Some(ref mut rtc_int) = rtc_int_ref.deref_mut() {
            if let Some(ref mut i2c) = i2c_int_ref.deref_mut() {
                if rtc_int.check_interrupt() {
                    nixie::rtc_tick(i2c);
                    rtc_int.clear_interrupt_pending_bit();
                }
            }
        }
    });
}

#[interrupt]
fn EXTI3() {
    free(|cs| {
        let mut nfault_ref = FAULT_INT.borrow(cs).borrow_mut();
        if let Some(ref mut nfault) = nfault_ref.deref_mut() {
            if nfault.check_interrupt() {
                nfault.clear_interrupt_pending_bit();
                panic!();
            }
        }
    });
}

#[interrupt]
fn TIM2() {
    free(|cs| {
        let mut i2c_int_ref = I2C.borrow(cs).borrow_mut();
        if let Some(ref mut i2c) = i2c_int_ref.deref_mut() {
            nixie::refresh_tick(i2c);
        }
    });
}

#[panic_handler]
#[cfg(not(test))]
/// Custom panic handler
fn panic(_info: &PanicInfo) -> ! {
    set_fault_led(State::High);
    loop {
        continue;
    }
}