pinda temp table changed back

Firmware/Marlin_main.cpp

@@ -233,6 +233,7 @@
 // M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
 // M605 - Set dual x-carriage movement mode: S<mode> [ X<duplication x-offset> R<duplication temp offset> ]
 // M860 - Wait for PINDA thermistor to reach target temperature.
+// M861 - Set / Read PINDA temperature compensation offsets
 // M900 - Set LIN_ADVANCE options, if enabled. See Configuration_adv.h for details.
 // M907 - Set digital trimpot motor current using axis codes.
 // M908 - Control digital trimpot directly.
@@ -6263,6 +6264,74 @@ Sigma_Exit:
 
 		break;
 	}
+	case 861: // M861 - Set/Read PINDA temperature compensation offsets
+		if (code_seen('?')) { // ? - Print out current EEPRO offset values
+			uint8_t cal_status = calibration_status_pinda();
+			cal_status ? SERIAL_PROTOCOLLN("PINDA cal status: 1") : SERIAL_PROTOCOLLN("PINDA cal status: 0");
+			SERIAL_PROTOCOLLN("index, temp, ustep, um");
+			for (uint8_t i = 0; i < 6; i++)
+			{
+				uint16_t usteps = 0;
+				if (i > 0) usteps = eeprom_read_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + (i - 1));
+				float mm = ((float)usteps) / axis_steps_per_unit[Z_AXIS];
+				i == 0 ? SERIAL_PROTOCOLPGM("n/a") : SERIAL_PROTOCOL(i - 1);
+				SERIAL_PROTOCOLPGM(", ");
+				SERIAL_PROTOCOL(35 + (i * 5));
+				SERIAL_PROTOCOLPGM(", ");
+				SERIAL_PROTOCOL(usteps);
+				SERIAL_PROTOCOLPGM(", ");
+				SERIAL_PROTOCOL(mm * 1000);
+				SERIAL_PROTOCOLLN("");
+			}
+		}
+		else if (code_seen('!')) { // ! - Set factory default values
+			eeprom_write_byte((uint8_t*)EEPROM_CALIBRATION_STATUS_PINDA, 1);
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 0, 8); //40C -  20um -   8usteps
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 1, 24); //45C -  60um -  24usteps
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 2, 48); //50C - 120um -  48usteps
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 3, 80); //55C - 200um -  80usteps
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 4, 120); //60C - 300um - 120usteps
+			SERIAL_PROTOCOLLN("factory restored");
+		}
+		else if (code_seen('Z')) { // Z - Set all values to 0 (effectively disabling PINDA temperature compensation)
+			eeprom_write_byte((uint8_t*)EEPROM_CALIBRATION_STATUS_PINDA, 1);
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 0, 0);
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 1, 0);
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 2, 0);
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 3, 0);
+			eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + 4, 0);
+			SERIAL_PROTOCOLLN("zerorized");
+		}
+		else if (code_seen('S')) { // Sxxx Iyyy - Set compensation ustep value S for compensation table index I
+			uint16_t usteps = code_value();
+			if (code_seen('I')) {
+				byte index = code_value();
+				if ((index >= 0) && (index < 5)) {
+					eeprom_write_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + index, usteps);
+					SERIAL_PROTOCOLLN("OK");
+					SERIAL_PROTOCOLLN("index, temp, ustep, um");
+					for (uint8_t i = 0; i < 6; i++)
+					{
+						uint16_t usteps = 0;
+						if (i > 0) usteps = eeprom_read_word(((uint16_t*)EEPROM_PROBE_TEMP_SHIFT) + (i - 1));
+						float mm = ((float)usteps) / axis_steps_per_unit[Z_AXIS];
+						i == 0 ? SERIAL_PROTOCOLPGM("n/a") : SERIAL_PROTOCOL(i - 1);
+						SERIAL_PROTOCOLPGM(", ");
+						SERIAL_PROTOCOL(35 + (i * 5));
+						SERIAL_PROTOCOLPGM(", ");
+						SERIAL_PROTOCOL(usteps);
+						SERIAL_PROTOCOLPGM(", ");
+						SERIAL_PROTOCOL(mm * 1000);
+						SERIAL_PROTOCOLLN("");
+					}
+				}
+			}
+		}
+		else {
+			SERIAL_PROTOCOLPGM("no valid command");
+		}
+		break;
+
 #endif //PINDA_THERMISTOR
 
 #ifdef LIN_ADVANCE

Firmware/temperature.cpp

@@ -985,7 +985,7 @@ static void updateTemperaturesFromRawValues()
     }
 
 #ifdef PINDA_THERMISTOR
-	current_temperature_pinda = analog2tempPINDA(current_temperature_raw_pinda);
+	current_temperature_pinda = analog2tempBed(current_temperature_raw_pinda);
 #endif
 
 #ifdef AMBIENT_THERMISTOR