mmu M600: dont use change extruder posibility; unload starts always imidiately

Firmware/Marlin_main.cpp

@@ -3097,7 +3097,7 @@ void gcode_M600(bool automatic, float x_position, float y_position, float z_shif
 		st_synchronize();
 		
 		//Beep, manage nozzle heater and wait for user to start unload filament
-		if(!automatic) M600_wait_for_user();
+		if(!mmu_enabled) M600_wait_for_user();
 		
 		lcd_change_fil_state = 0;
 		

Firmware/mmu.cpp

@@ -9,6 +9,7 @@
 #include "Configuration_prusa.h"
 #include "fsensor.h"
 #include "cardreader.h"
+#include "sound.h"
 
 
 extern const char* lcd_display_message_fullscreen_P(const char *msg);
@@ -410,6 +411,43 @@ void mmu_load_to_nozzle()
 	if (!saved_e_relative_mode) axis_relative_modes[E_AXIS] = false;
 }
 
+void mmu_M600_wait_and_beep() {
+		//Beep and wait for user to remove old filament and prepare new filament for load
+
+		KEEPALIVE_STATE(PAUSED_FOR_USER);
+
+		int counterBeep = 0;
+		lcd_display_message_fullscreen_P(_i("Remove old filament and press the knob to start loading new filament."));
+		bool bFirst=true;
+
+		while (!lcd_clicked()){
+			manage_heater();
+			manage_inactivity(true);
+
+			#if BEEPER > 0
+			if (counterBeep == 500) {
+				counterBeep = 0;
+			}
+			SET_OUTPUT(BEEPER);
+			if (counterBeep == 0) {
+				if((eSoundMode==e_SOUND_MODE_LOUD)||((eSoundMode==e_SOUND_MODE_ONCE)&&bFirst))
+				{
+					bFirst=false;
+					WRITE(BEEPER, HIGH);
+				}
+			}
+			if (counterBeep == 20) {
+				WRITE(BEEPER, LOW);
+			}
+				
+			counterBeep++;
+			#endif //BEEPER > 0
+
+			delay_keep_alive(4);
+		}
+		WRITE(BEEPER, LOW);
+}
+
 void mmu_M600_load_filament(bool automatic)
 { 
 	//load filament for mmu v2
@@ -417,10 +455,14 @@ void mmu_M600_load_filament(bool automatic)
 		  bool response = false;
 		  bool yes = false;
 		  if (!automatic) {
+			  mmu_M600_wait_and_beep();
+#ifdef MMU_M600_SWITCH_EXTRUDER
 			  yes = lcd_show_fullscreen_message_yes_no_and_wait_P(_i("Do you want to switch extruder?"), false);
 			  if(yes) tmp_extruder = choose_extruder_menu();
 			  else tmp_extruder = mmu_extruder;
-
+#else 
+			  tmp_extruder = mmu_extruder; 
+#endif //MMU_M600_SWITCH_EXTRUDER
 		  }
 		  else {
 			  tmp_extruder = (tmp_extruder+1)%5;

Firmware/mmu.h

@@ -56,7 +56,7 @@ extern void manage_response(bool move_axes, bool turn_off_nozzle);
 extern void mmu_load_to_nozzle();
 
 extern void mmu_M600_load_filament(bool automatic);
-
+extern void mmu_M600_wait_and_beep();
 
 extern void extr_mov(float shift, float feed_rate);
 extern void change_extr(int extr);