|
|
@@ -1,421 +0,0 @@
|
|
|
-#ifndef CONFIGURATION_PRUSA_H
|
|
|
-#define CONFIGURATION_PRUSA_H
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- GENERAL SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Printer revision
|
|
|
-#define FILAMENT_SIZE "1_75mm_MK3"
|
|
|
-#define NOZZLE_TYPE "E3Dv6full"
|
|
|
-
|
|
|
-// Developer flag
|
|
|
-#define DEVELOPER
|
|
|
-
|
|
|
-// Printer name
|
|
|
-#define CUSTOM_MENDEL_NAME "Prusa i3 MK3"
|
|
|
-
|
|
|
-// Electronics
|
|
|
-#define MOTHERBOARD BOARD_EINY_0_1a
|
|
|
-
|
|
|
-
|
|
|
-
|
|
|
-// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
|
|
|
-//#define E3D_PT100_EXTRUDER_WITH_AMP
|
|
|
-//#define E3D_PT100_EXTRUDER_NO_AMP
|
|
|
-//#define E3D_PT100_BED_WITH_AMP
|
|
|
-//#define E3D_PT100_BED_NO_AMP
|
|
|
-
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- AXIS SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Steps per unit {X,Y,Z,E}
|
|
|
-#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,140}
|
|
|
-
|
|
|
-// Endstop inverting
|
|
|
-const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
|
|
-const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
|
|
-const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
|
|
-
|
|
|
-// Home position
|
|
|
-#define MANUAL_X_HOME_POS 0
|
|
|
-#define MANUAL_Y_HOME_POS -2.2
|
|
|
-#define MANUAL_Z_HOME_POS 0.2
|
|
|
-
|
|
|
-// Travel limits after homing
|
|
|
-#define X_MAX_POS 255
|
|
|
-#define X_MIN_POS 0
|
|
|
-#define Y_MAX_POS 210
|
|
|
-#define Y_MIN_POS -4
|
|
|
-#define Z_MAX_POS 210
|
|
|
-#define Z_MIN_POS 0.15
|
|
|
-
|
|
|
-// Canceled home position
|
|
|
-#define X_CANCEL_POS 50
|
|
|
-#define Y_CANCEL_POS 190
|
|
|
-
|
|
|
-//Pause print position
|
|
|
-#define X_PAUSE_POS 50
|
|
|
-#define Y_PAUSE_POS 190
|
|
|
-#define Z_PAUSE_LIFT 20
|
|
|
-
|
|
|
-#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
|
|
|
-#define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000
|
|
|
-
|
|
|
-#define DEFAULT_MAX_FEEDRATE {400, 400, 12, 120} // (mm/sec)
|
|
|
-#define DEFAULT_MAX_ACCELERATION {2000,2000,500,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
|
|
-
|
|
|
-#define DEFAULT_ACCELERATION 1200 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
|
|
-#define DEFAULT_RETRACT_ACCELERATION 1500 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
|
|
-
|
|
|
-
|
|
|
-#define MANUAL_FEEDRATE {3000, 3000, 1000, 100} // set the speeds for manual moves (mm/min)
|
|
|
-
|
|
|
-#define Z_AXIS_ALWAYS_ON 1
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- TMC2130 default settings
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// PWM register configuration
|
|
|
-#define PWM_GRAD 0x08 // 0x0F - Sets gradient - (max 15 with PWM autoscale activated)
|
|
|
-#define PWM_AMPL 0xC8 // 0xFF - Sets PWM amplitude to 200 (max is 255)
|
|
|
-#define PWM_AUTOSCALE 0x04 // 0x04 since writing in PWM_CONF (Activates PWM autoscaling)
|
|
|
-#define PWM_FREQ 0x01 // 0x01 since writing in PWM_CONF (Sets PWM frequency to 2/683 fCLK)
|
|
|
-#define PWM_THRS 0x00 // TPWM_THRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode
|
|
|
-
|
|
|
-#define SG_HOMING_SW 1 // stallguard "software" homing
|
|
|
-//#define SG_HOMING_HW 1 // stallguard "hardware" homing
|
|
|
-#define SG_THRESHOLD_X 8 // stallguard sensitivity for X axis
|
|
|
-#define SG_THRESHOLD_Y 8 // stallguard sensitivity for Y axis
|
|
|
-#define TCOOLTHRS 239 // coolstep treshold
|
|
|
-
|
|
|
-#define TMC2130_CURRENTS_H {2, 2, 2, 4} // default holding currents for all axes
|
|
|
-#define TMC2130_CURRENTS_R {6, 6, 8, 8} // default running currents for all axes
|
|
|
-#define TMC2130_DEBUG
|
|
|
-//#define TMC_DBG_READS
|
|
|
-//#define TMC_DBG_WRITE
|
|
|
-
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- EXTRUDER SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Mintemps
|
|
|
-#define HEATER_0_MINTEMP 15
|
|
|
-#define HEATER_1_MINTEMP 5
|
|
|
-#define HEATER_2_MINTEMP 5
|
|
|
-#define BED_MINTEMP 15
|
|
|
-
|
|
|
-// Maxtemps
|
|
|
-#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
|
|
|
-#define HEATER_0_MAXTEMP 410
|
|
|
-#else
|
|
|
-#define HEATER_0_MAXTEMP 305
|
|
|
-#endif
|
|
|
-#define HEATER_1_MAXTEMP 305
|
|
|
-#define HEATER_2_MAXTEMP 305
|
|
|
-#define BED_MAXTEMP 150
|
|
|
-
|
|
|
-#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
|
|
|
-// Define PID constants for extruder with PT100
|
|
|
-#define DEFAULT_Kp 21.70
|
|
|
-#define DEFAULT_Ki 1.60
|
|
|
-#define DEFAULT_Kd 73.76
|
|
|
-#else
|
|
|
-// Define PID constants for extruder
|
|
|
-#define DEFAULT_Kp 40.925
|
|
|
-#define DEFAULT_Ki 4.875
|
|
|
-#define DEFAULT_Kd 86.085
|
|
|
-#endif
|
|
|
-
|
|
|
-// Extrude mintemp
|
|
|
-#define EXTRUDE_MINTEMP 130
|
|
|
-
|
|
|
-// Extruder cooling fans
|
|
|
-#define EXTRUDER_0_AUTO_FAN_PIN 8
|
|
|
-#define EXTRUDER_1_AUTO_FAN_PIN -1
|
|
|
-#define EXTRUDER_2_AUTO_FAN_PIN -1
|
|
|
-#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
|
|
|
-#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
|
|
|
-
|
|
|
-
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- LOAD/UNLOAD FILAMENT SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Load filament commands
|
|
|
-#define LOAD_FILAMENT_0 "M83"
|
|
|
-#define LOAD_FILAMENT_1 "G1 E70 F400"
|
|
|
-#define LOAD_FILAMENT_2 "G1 E40 F100"
|
|
|
-
|
|
|
-// Unload filament commands
|
|
|
-#define UNLOAD_FILAMENT_0 "M83"
|
|
|
-#define UNLOAD_FILAMENT_1 "G1 E-80 F7000"
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- CHANGE FILAMENT SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Filament change configuration
|
|
|
-#define FILAMENTCHANGEENABLE
|
|
|
-#ifdef FILAMENTCHANGEENABLE
|
|
|
-#define FILAMENTCHANGE_XPOS 211
|
|
|
-#define FILAMENTCHANGE_YPOS 0
|
|
|
-#define FILAMENTCHANGE_ZADD 2
|
|
|
-#define FILAMENTCHANGE_FIRSTRETRACT -2
|
|
|
-#define FILAMENTCHANGE_FINALRETRACT -80
|
|
|
-
|
|
|
-#define FILAMENTCHANGE_FIRSTFEED 70
|
|
|
-#define FILAMENTCHANGE_FINALFEED 50
|
|
|
-#define FILAMENTCHANGE_RECFEED 5
|
|
|
-
|
|
|
-#define FILAMENTCHANGE_XYFEED 50
|
|
|
-#define FILAMENTCHANGE_EFEED 20
|
|
|
-#define FILAMENTCHANGE_RFEED 400
|
|
|
-#define FILAMENTCHANGE_EXFEED 2
|
|
|
-#define FILAMENTCHANGE_ZFEED 15
|
|
|
-
|
|
|
-#endif
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- ADDITIONAL FEATURES SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Define Prusa filament runout sensor
|
|
|
-//#define FILAMENT_RUNOUT_SUPPORT
|
|
|
-
|
|
|
-#ifdef FILAMENT_RUNOUT_SUPPORT
|
|
|
-#define FILAMENT_RUNOUT_SENSOR 1
|
|
|
-#endif
|
|
|
-
|
|
|
-// temperature runaway
|
|
|
-//#define TEMP_RUNAWAY_BED_HYSTERESIS 5
|
|
|
-//#define TEMP_RUNAWAY_BED_TIMEOUT 360
|
|
|
-
|
|
|
-#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
|
|
|
-#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- MOTOR CURRENT SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Motor Current setting for BIG RAMBo
|
|
|
-#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
|
|
|
-#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135}
|
|
|
-
|
|
|
-// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range
|
|
|
-#if MOTHERBOARD == 102 || MOTHERBOARD == 302 || MOTHERBOARD == 300
|
|
|
-#define MOTOR_CURRENT_PWM_RANGE 2000
|
|
|
-#define DEFAULT_PWM_MOTOR_CURRENT {400, 750, 750} // {XY,Z,E}
|
|
|
-#define DEFAULT_PWM_MOTOR_CURRENT_LOUD {400, 750, 750} // {XY,Z,E}
|
|
|
-#endif
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- BED SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-// Define Mesh Bed Leveling system to enable it
|
|
|
-#define MESH_BED_LEVELING
|
|
|
-#ifdef MESH_BED_LEVELING
|
|
|
-
|
|
|
-#define MBL_Z_STEP 0.01
|
|
|
-
|
|
|
-// Mesh definitions
|
|
|
-#define MESH_MIN_X 35
|
|
|
-#define MESH_MAX_X 238
|
|
|
-#define MESH_MIN_Y 6
|
|
|
-#define MESH_MAX_Y 202
|
|
|
-
|
|
|
-// Mesh upsample definition
|
|
|
-#define MESH_NUM_X_POINTS 7
|
|
|
-#define MESH_NUM_Y_POINTS 7
|
|
|
-// Mesh measure definition
|
|
|
-#define MESH_MEAS_NUM_X_POINTS 3
|
|
|
-#define MESH_MEAS_NUM_Y_POINTS 3
|
|
|
-
|
|
|
-#define MESH_HOME_Z_CALIB 0.2
|
|
|
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
|
|
|
-
|
|
|
-#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right
|
|
|
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 9 // Z probe to nozzle Y offset: -front +behind
|
|
|
-#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!)
|
|
|
-#endif
|
|
|
-
|
|
|
-// Bed Temperature Control
|
|
|
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
|
|
-//
|
|
|
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
|
|
-// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
|
|
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
|
|
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
|
|
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
|
|
-// shouldn't use bed PID until someone else verifies your hardware works.
|
|
|
-// If this is enabled, find your own PID constants below.
|
|
|
-#define PIDTEMPBED
|
|
|
-//
|
|
|
-//#define BED_LIMIT_SWITCHING
|
|
|
-
|
|
|
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
|
|
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
|
|
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
|
|
-// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
|
|
-#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
|
|
-
|
|
|
-// Bed temperature compensation settings
|
|
|
-#define BED_OFFSET 10
|
|
|
-#define BED_OFFSET_START 40
|
|
|
-#define BED_OFFSET_CENTER 50
|
|
|
-
|
|
|
-
|
|
|
-#ifdef PIDTEMPBED
|
|
|
-//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
|
|
-//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
|
|
-#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
|
|
|
-// Define PID constants for extruder with PT100
|
|
|
-#define DEFAULT_bedKp 21.70
|
|
|
-#define DEFAULT_bedKi 1.60
|
|
|
-#define DEFAULT_bedKd 73.76
|
|
|
-#else
|
|
|
-#define DEFAULT_bedKp 126.13
|
|
|
-#define DEFAULT_bedKi 4.30
|
|
|
-#define DEFAULT_bedKd 924.76
|
|
|
-#endif
|
|
|
-
|
|
|
-//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
|
|
-//from pidautotune
|
|
|
-// #define DEFAULT_bedKp 97.1
|
|
|
-// #define DEFAULT_bedKi 1.41
|
|
|
-// #define DEFAULT_bedKd 1675.16
|
|
|
-
|
|
|
-// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
|
|
-#endif // PIDTEMPBED
|
|
|
-
|
|
|
-
|
|
|
-/*-----------------------------------
|
|
|
- PREHEAT SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-#define PLA_PREHEAT_HOTEND_TEMP 215
|
|
|
-#define PLA_PREHEAT_HPB_TEMP 55
|
|
|
-#define PLA_PREHEAT_FAN_SPEED 0
|
|
|
-
|
|
|
-#define ABS_PREHEAT_HOTEND_TEMP 255
|
|
|
-#define ABS_PREHEAT_HPB_TEMP 100
|
|
|
-#define ABS_PREHEAT_FAN_SPEED 0
|
|
|
-
|
|
|
-#define HIPS_PREHEAT_HOTEND_TEMP 220
|
|
|
-#define HIPS_PREHEAT_HPB_TEMP 100
|
|
|
-#define HIPS_PREHEAT_FAN_SPEED 0
|
|
|
-
|
|
|
-#define PP_PREHEAT_HOTEND_TEMP 254
|
|
|
-#define PP_PREHEAT_HPB_TEMP 100
|
|
|
-#define PP_PREHEAT_FAN_SPEED 0
|
|
|
-
|
|
|
-#define PET_PREHEAT_HOTEND_TEMP 240
|
|
|
-#define PET_PREHEAT_HPB_TEMP 90
|
|
|
-#define PET_PREHEAT_FAN_SPEED 0
|
|
|
-
|
|
|
-#define FLEX_PREHEAT_HOTEND_TEMP 230
|
|
|
-#define FLEX_PREHEAT_HPB_TEMP 50
|
|
|
-#define FLEX_PREHEAT_FAN_SPEED 0
|
|
|
-
|
|
|
-/*------------------------------------
|
|
|
- THERMISTORS SETTINGS
|
|
|
- *------------------------------------*/
|
|
|
-
|
|
|
-//
|
|
|
-//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
|
|
-//
|
|
|
-//// Temperature sensor settings:
|
|
|
-// -2 is thermocouple with MAX6675 (only for sensor 0)
|
|
|
-// -1 is thermocouple with AD595
|
|
|
-// 0 is not used
|
|
|
-// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
|
|
-// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
|
|
-// 3 is Mendel-parts thermistor (4.7k pullup)
|
|
|
-// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
|
|
-// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
|
|
|
-// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
|
|
-// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
|
|
|
-// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
|
|
|
-// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
|
|
-// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
|
|
-// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
|
|
-// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
|
|
-// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
|
|
-// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
|
|
-// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
|
|
-// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
|
|
-//
|
|
|
-// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
|
|
-// (but gives greater accuracy and more stable PID)
|
|
|
-// 51 is 100k thermistor - EPCOS (1k pullup)
|
|
|
-// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
|
|
|
-// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
|
|
|
-//
|
|
|
-// 1047 is Pt1000 with 4k7 pullup
|
|
|
-// 1010 is Pt1000 with 1k pullup (non standard)
|
|
|
-// 147 is Pt100 with 4k7 pullup
|
|
|
-// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a
|
|
|
-// 247 is Pt100 with 4k7 pullup and PT100 Amplifier
|
|
|
-// 110 is Pt100 with 1k pullup (non standard)
|
|
|
-
|
|
|
-#if defined(E3D_PT100_EXTRUDER_WITH_AMP)
|
|
|
-#define TEMP_SENSOR_0 247
|
|
|
-#elif defined(E3D_PT100_EXTRUDER_NO_AMP)
|
|
|
-#define TEMP_SENSOR_0 148
|
|
|
-#else
|
|
|
-#define TEMP_SENSOR_0 5
|
|
|
-#endif
|
|
|
-#define TEMP_SENSOR_1 0
|
|
|
-#define TEMP_SENSOR_2 0
|
|
|
-#if defined(E3D_PT100_BED_WITH_AMP)
|
|
|
-#define TEMP_SENSOR_BED 247
|
|
|
-#elif defined(E3D_PT100_BED_NO_AMP)
|
|
|
-#define TEMP_SENSOR_BED 148
|
|
|
-#else
|
|
|
-#define TEMP_SENSOR_BED 1
|
|
|
-#endif
|
|
|
-
|
|
|
-#define STACK_GUARD_TEST_VALUE 0xA2A2
|
|
|
-
|
|
|
-#define MAX_BED_TEMP_CALIBRATION 50
|
|
|
-#define MAX_HOTEND_TEMP_CALIBRATION 50
|
|
|
-
|
|
|
-#define MAX_E_STEPS_PER_UNIT 250
|
|
|
-#define MIN_E_STEPS_PER_UNIT 100
|
|
|
-
|
|
|
-#define Z_BABYSTEP_MIN -3999
|
|
|
-#define Z_BABYSTEP_MAX 0
|
|
|
-
|
|
|
-#define PINDA_PREHEAT_X 70
|
|
|
-#define PINDA_PREHEAT_Y -3
|
|
|
-#define PINDA_PREHEAT_Z 1
|
|
|
-#define PINDA_HEAT_T 120 //time in s
|
|
|
-
|
|
|
-#define PINDA_MIN_T 50
|
|
|
-#define PINDA_STEP_T 10
|
|
|
-#define PINDA_MAX_T 100
|
|
|
-
|
|
|
-#define PING_TIME 60 //time in s
|
|
|
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes
|
|
|
-#define PING_ALLERT_PERIOD 60 //time in s
|
|
|
-
|
|
|
-#define LONG_PRESS_TIME 1000 //time in ms for button long press
|
|
|
-#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
|
|
|
-
|
|
|
-#define DEFAULT_PID_TEMP 210
|
|
|
-
|
|
|
-#define MIN_PRINT_FAN_SPEED 50
|
|
|
-
|
|
|
-#ifdef SNMM
|
|
|
-#define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print
|
|
|
-#else
|
|
|
-#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print
|
|
|
-#endif
|
|
|
-
|
|
|
-#endif //__CONFIGURATION_PRUSA_H
|
michalprusa