Merge branch 'MK3' into MK3_prep_Arudino-Boards_102

Firmware/Marlin_main.cpp

@@ -1242,8 +1242,8 @@ void setup()
         // Once a firmware boots up, it forces at least a language selection, which changes
         // EEPROM_LANG to number lower than 0x0ff.
         // 1) Set a high power mode.
+	    eeprom_update_byte((uint8_t*)EEPROM_SILENT, SILENT_MODE_OFF);
 #ifdef TMC2130
-        eeprom_write_byte((uint8_t*)EEPROM_SILENT, 0);
         tmc2130_mode = TMC2130_MODE_NORMAL;
 #endif //TMC2130
         eeprom_write_byte((uint8_t*)EEPROM_WIZARD_ACTIVE, 1); //run wizard
@@ -2433,6 +2433,9 @@ void ramming() {
 
 #ifdef TMC2130
 void force_high_power_mode(bool start_high_power_section) {
+#ifdef PSU_Delta
+	if (start_high_power_section == true) enable_force_z();
+#endif //PSU_Delta
 	uint8_t silent;
 	silent = eeprom_read_byte((uint8_t*)EEPROM_SILENT);
 	if (silent == 1) {

Firmware/stepper.cpp

@@ -1564,10 +1564,6 @@ void st_current_init() //Initialize Digipot Motor Current
 {
 #ifdef MOTOR_CURRENT_PWM_XY_PIN
   uint8_t SilentMode = eeprom_read_byte((uint8_t*)EEPROM_SILENT);
-  if (SilentMode == 0xff){ //set power to High Power (MK2.5) or Normal Power (MK3, unused)
-    SilentMode = SILENT_MODE_POWER;
-    eeprom_update_byte((uint8_t*)EEPROM_SILENT, SilentMode);
-  }
   SilentModeMenu = SilentMode;
     pinMode(MOTOR_CURRENT_PWM_XY_PIN, OUTPUT);
     pinMode(MOTOR_CURRENT_PWM_Z_PIN, OUTPUT);

Firmware/ultralcd.cpp

@@ -1843,8 +1843,8 @@ static void lcd_menu_fails_stats_total()
 //! @code{.unparsed}
 //! |01234567890123456789|
 //! |Last print failures |	c=20 r=1
-//! | Power failures: 000|	c=14 r=1
-//! | Filam. runouts: 000|	c=14 r=1
+//! | Power failures  000|	c=14 r=1
+//! | Filam. runouts  000|	c=14 r=1
 //! | Crash   X:000 Y:000|	c=7 r=1
 //! ----------------------
 //! @endcode
@@ -1890,6 +1890,7 @@ static void lcd_menu_fails_stats()
 }
 
 #elif defined(FILAMENT_SENSOR)
+static const char failStatsFmt[] PROGMEM = "%S\n" " %-16.16S%-3d\n" "%S\n" " %-16.16S%-3d\n";
 //! 
 //! @brief Print last print and total filament run outs
 //! 
@@ -1900,9 +1901,9 @@ static void lcd_menu_fails_stats()
 //! @code{.unparsed}
 //! |01234567890123456789|
 //! |Last print failures |	c=20 r=1
-//! | Filam. runouts: 000|	c=14 r=1
+//! | Filam. runouts  000|	c=14 r=1
 //! |Total failures      |	c=20 r=1
-//! | Filam. runouts: 000|	c=14 r=1
+//! | Filam. runouts  000|	c=14 r=1
 //! ----------------------
 //! @endcode
 //! @todo Positioning of the messages and values on LCD aren't fixed to their exact place. This causes issues with translations.
@@ -1912,11 +1913,13 @@ static void lcd_menu_fails_stats()
     uint8_t filamentLast = eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT);
     uint16_t filamentTotal = eeprom_read_word((uint16_t*)EEPROM_FERROR_COUNT_TOT);
 	lcd_home();
-    lcd_printf_P(PSTR("Last print failures\n"  ////c=20 r=1 
-        " Filam. runouts  %-3d\n"   ////c=14 r=1
-        "Total failures\n"  ////c=20 r=1
-        " Filam. runouts  %-3d"), filamentLast, filamentTotal);  ////c=14 r=1
-    menu_back_if_clicked();
+	lcd_printf_P(failStatsFmt, 
+        _i("Last print failures"),   ////c=20 r=1
+        _i("Filam. runouts"), filamentLast,   ////c=14 r=1
+        _i("Total failures"),  ////c=20 r=1
+        _i("Filam. runouts"), filamentTotal);   ////c=14 r=1
+
+	menu_back_if_clicked();
 }
 #else
 static void lcd_menu_fails_stats()

lang/lang_en_cz.txt

@@ -72,7 +72,7 @@
 
 #MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
 "Autoloading filament available only when filament sensor is turned on..."
-"Automaticke zavadeni filamentu je dostupne pouze pri zapnutem filament senzoru..."
+"Automaticke zavadeni filamentu je mozne pouze pri zapnutem filament senzoru..."
 
 #MSG_AUTOLOADING_ENABLED c=20 r=4
 "Autoloading filament is active, just press the knob and insert filament..."

lang/lang_en_es.txt

@@ -72,11 +72,11 @@
 
 #MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
 "Autoloading filament available only when filament sensor is turned on..."
-"La carga automatica de filamento solo funciona si el sensor de filamento esta activado..."
+"La carga automatica solo funciona si el sensor de filamento esta activado..."
 
 #MSG_AUTOLOADING_ENABLED c=20 r=4
 "Autoloading filament is active, just press the knob and insert filament..."
-"La carga automatica de filamento esta activada, pulse el dial e inserte el filamento..."
+"La carga automatica esta activada, pulse el dial e inserte el filamento..."
 
 #MSG_SELFTEST_AXIS_LENGTH
 "Axis length"

lang/lang_en_pl.txt

@@ -72,7 +72,7 @@
 
 #MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
 "Autoloading filament available only when filament sensor is turned on..."
-"Autoladowanie filamentu dostepne tylko gdy czujnik filamentu jest wlaczony..."
+"Autoladowanie fil. dostepne tylko gdy czujnik filamentu jest wlaczony..."
 
 #MSG_AUTOLOADING_ENABLED c=20 r=4
 "Autoloading filament is active, just press the knob and insert filament..."