Unbreak build with !PINDA_THERMISTOR

Firmware/Marlin_main.cpp

@@ -2864,7 +2864,7 @@ static void gcode_G80()
         run = true;
         repeatcommand_front(); // repeat G80 with all its parameters
         enquecommand_front_P(G28W0);
-        break;
+        return;
     }
     run = false;
 #endif //PINDA_THERMISTOR
@@ -10281,12 +10281,12 @@ static void temp_compensation_start() {
 	if ((int)degHotend(active_extruder) > extrude_min_temp) {
 		current_position[E_AXIS] -= default_retraction;
 	}
-	plan_buffer_line_curposXYZE(400, active_extruder);
+	plan_buffer_line_curposXYZE(400);
 	
 	current_position[X_AXIS] = PINDA_PREHEAT_X;
 	current_position[Y_AXIS] = PINDA_PREHEAT_Y;
 	current_position[Z_AXIS] = PINDA_PREHEAT_Z;
-	plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
+	plan_buffer_line_curposXYZE(3000 / 60);
 	st_synchronize();
 	while (fabs(degBed() - target_temperature_bed) > 1) delay_keep_alive(1000);
 
@@ -10305,7 +10305,7 @@ static void temp_compensation_apply() {
 	int z_shift = 0;
 	float z_shift_mm;
 
-	if (calibration_status() == CALIBRATION_STATUS_CALIBRATED) {
+	if (calibration_status_pinda()) {
 		if (target_temperature_bed % 10 == 0 && target_temperature_bed >= 60 && target_temperature_bed <= 100) {
 			i_add = (target_temperature_bed - 60) / 10;
 			z_shift = eeprom_read_word((uint16_t*)EEPROM_PROBE_TEMP_SHIFT + i_add);

Firmware/ultralcd.cpp

@@ -4719,11 +4719,10 @@ static void lcd_settings_menu()
 #if defined (TMC2130) && defined (LINEARITY_CORRECTION)
     MENU_ITEM_SUBMENU_P(_i("Lin. correction"), lcd_settings_linearity_correction_menu);////MSG_LIN_CORRECTION c=18
 #endif //LINEARITY_CORRECTION && TMC2130
+#ifdef PINDA_THERMISTOR
     if(has_temperature_compensation())
-    {
         MENU_ITEM_TOGGLE_P(_T(MSG_PINDA_CALIBRATION), eeprom_read_byte((unsigned char *)EEPROM_TEMP_CAL_ACTIVE) ? _T(MSG_ON) : _T(MSG_OFF), lcd_temp_calibration_set);
-    }
-
+#endif
 #ifdef HAS_SECOND_SERIAL_PORT
     MENU_ITEM_TOGGLE_P(_T(MSG_RPI_PORT), (selectedSerialPort == 0) ? _T(MSG_OFF) : _T(MSG_ON), lcd_second_serial_set);
 #endif //HAS_SECOND_SERIAL
@@ -4825,10 +4824,10 @@ static void lcd_calibration_menu()
     MENU_ITEM_SUBMENU_P(_i("Show end stops"), menu_show_end_stops);////MSG_SHOW_END_STOPS c=18
 #endif
     MENU_ITEM_GCODE_P(_i("Reset XYZ calibr."), PSTR("M44"));////MSG_CALIBRATE_BED_RESET c=18
+#ifdef PINDA_THERMISTOR
     if(has_temperature_compensation())
-    {
 	    MENU_ITEM_FUNCTION_P(_T(MSG_PINDA_CALIBRATION), lcd_calibrate_pinda);
-    }
+#endif
   }
 #ifdef TEMP_MODEL
     MENU_ITEM_SUBMENU_P(_n("Temp Model cal."), lcd_temp_model_cal);