temp. calibration is automaticly activated after calibration process

Firmware/Marlin_main.cpp

@@ -3556,6 +3556,9 @@ void process_commands()
 			setTargetBed(0); //set bed target temperature back to 0
 //			setTargetHotend(0,0); //set hotend target temperature back to 0
 			lcd_show_fullscreen_message_and_wait_P(MSG_TEMP_CALIBRATION_DONE);
+			temp_cal_active = true;
+			eeprom_update_byte((unsigned char *)EEPROM_TEMP_CAL_ACTIVE, 1);
+
 			lcd_update_enable(true);
 			lcd_update(2);
 			break;
@@ -3669,6 +3672,8 @@ void process_commands()
 			disable_e2();
 			setTargetBed(0); //set bed target temperature back to 0
 		lcd_show_fullscreen_message_and_wait_P(MSG_TEMP_CALIBRATION_DONE);
+		temp_cal_active = true;
+		eeprom_update_byte((unsigned char *)EEPROM_TEMP_CAL_ACTIVE, 1);
 		lcd_update_enable(true);
 		lcd_update(2);		
 

Firmware/language_all.cpp

@@ -2197,8 +2197,8 @@ const char * const MSG_TEMP_CALIBRATION_LANG_TABLE[LANG_NUM] PROGMEM = {
 	MSG_TEMP_CALIBRATION_CZ
 };
 
-const char MSG_TEMP_CALIBRATION_DONE_EN[] PROGMEM = "Temperature calibration is finished. Click to continue.";
-const char MSG_TEMP_CALIBRATION_DONE_CZ[] PROGMEM = "Teplotni kalibrace dokoncena. Pokracujte stiskem tlacitka.";
+const char MSG_TEMP_CALIBRATION_DONE_EN[] PROGMEM = "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal.";
+const char MSG_TEMP_CALIBRATION_DONE_CZ[] PROGMEM = "Teplotni kalibrace dokoncena a je nyni aktivni. Teplotni kalibraci je mozno deaktivovat v menu Nastaveni->Tepl. kal.";
 const char * const MSG_TEMP_CALIBRATION_DONE_LANG_TABLE[LANG_NUM] PROGMEM = {
 	MSG_TEMP_CALIBRATION_DONE_EN,
 	MSG_TEMP_CALIBRATION_DONE_CZ

Firmware/language_cz.h

@@ -303,7 +303,7 @@
 #define MSG_PINDA_NOT_CALIBRATED						"Tiskarna nebyla teplotne zkalibrovana"
 #define MSG_PINDA_PREHEAT								"Nahrivani PINDA"
 #define MSG_TEMP_CALIBRATION							"Tepl. kal.          "
-#define MSG_TEMP_CALIBRATION_DONE						"Teplotni kalibrace dokoncena. Pokracujte stiskem tlacitka."
+#define MSG_TEMP_CALIBRATION_DONE						"Teplotni kalibrace dokoncena a je nyni aktivni. Teplotni kalibraci je mozno deaktivovat v menu Nastaveni->Tepl. kal."
 #define MSG_TEMP_CALIBRATION_ON							"Tepl. kal.  [zap]"
 #define MSG_TEMP_CALIBRATION_OFF						"Tepl. kal.  [vyp]"
 #define MSG_PREPARE_FILAMENT							"Pripravte filament"

Firmware/language_en.h

@@ -303,7 +303,7 @@
 #define(length=20, lines=4) MSG_PINDA_NOT_CALIBRATED			"Temperature calibration has not been run yet"
 #define(length=20, lines=1) MSG_PINDA_PREHEAT					"PINDA Heating"
 #define(length=20, lines=1) MSG_TEMP_CALIBRATION				"Temp. cal.          "
-#define(length=20, lines=4) MSG_TEMP_CALIBRATION_DONE			"Temperature calibration is finished. Click to continue."
+#define(length=20, lines=12) MSG_TEMP_CALIBRATION_DONE			"Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 #define(length=20, lines=1) MSG_TEMP_CALIBRATION_ON				"Temp. cal.   [on]"
 #define(length=20, lines=1) MSG_TEMP_CALIBRATION_OFF			"Temp. cal.  [off]"
 #define(length=20, lines=1) MSG_PREPARE_FILAMENT				"Prepare new filament"