Merge pull request #1723 from PavelSindler/MK2_bed_temp

Heatbed maxtemp reduced to 125 C (MK2)

Firmware/variants/1_75mm_MK1-RAMBo10a-E3Dv6full.h

@@ -102,7 +102,7 @@ EXTRUDER SETTINGS
 #endif
 #define HEATER_1_MAXTEMP 305
 #define HEATER_2_MAXTEMP 305
-#define BED_MAXTEMP 150
+#define BED_MAXTEMP 125
 
 #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
 // Define PID constants for extruder with PT100

Firmware/variants/1_75mm_MK1-RAMBo13a-E3Dv6full.h

@@ -102,7 +102,7 @@ EXTRUDER SETTINGS
 #endif
 #define HEATER_1_MAXTEMP 305
 #define HEATER_2_MAXTEMP 305
-#define BED_MAXTEMP 150
+#define BED_MAXTEMP 125
 
 #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
 // Define PID constants for extruder with PT100

Firmware/variants/1_75mm_MK2-MultiMaterial-RAMBo10a-E3Dv6full.h

@@ -99,7 +99,7 @@ EXTRUDER SETTINGS
 #endif
 #define HEATER_1_MAXTEMP 305
 #define HEATER_2_MAXTEMP 305
-#define BED_MAXTEMP 150
+#define BED_MAXTEMP 125
 
 #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
 // Define PID constants for extruder with PT100

Firmware/variants/1_75mm_MK2-MultiMaterial-RAMBo13a-E3Dv6full.h

@@ -99,7 +99,7 @@ EXTRUDER SETTINGS
 #endif
 #define HEATER_1_MAXTEMP 305
 #define HEATER_2_MAXTEMP 305
-#define BED_MAXTEMP 150
+#define BED_MAXTEMP 125
 
 #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
 // Define PID constants for extruder with PT100

Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h

@@ -99,7 +99,7 @@ EXTRUDER SETTINGS
 #endif
 #define HEATER_1_MAXTEMP 305
 #define HEATER_2_MAXTEMP 305
-#define BED_MAXTEMP 150
+#define BED_MAXTEMP 125
 
 #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
 // Define PID constants for extruder with PT100

Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h

@@ -99,7 +99,7 @@ EXTRUDER SETTINGS
 #endif
 #define HEATER_1_MAXTEMP 305
 #define HEATER_2_MAXTEMP 305
-#define BED_MAXTEMP 150
+#define BED_MAXTEMP 125
 
 #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
 // Define PID constants for extruder with PT100