Merge pull request #3495 from wavexx/extrude_min_temp

Replace EXTRUDE_MINTEMP with the configurable extrude_min_temp

Firmware/Marlin_main.cpp

@@ -3376,7 +3376,7 @@ static void gcode_G80()
     go_home_with_z_lift();
     //		SERIAL_ECHOLNPGM("Go home finished");
     //unretract (after PINDA preheat retraction)
-    if ((degHotend(active_extruder) > EXTRUDE_MINTEMP) && eeprom_read_byte((unsigned char *)EEPROM_TEMP_CAL_ACTIVE) && calibration_status_pinda() && (target_temperature_bed >= 50)) {
+    if (((int)degHotend(active_extruder) > extrude_min_temp) && eeprom_read_byte((unsigned char *)EEPROM_TEMP_CAL_ACTIVE) && calibration_status_pinda() && (target_temperature_bed >= 50)) {
         current_position[E_AXIS] += default_retraction;
         plan_buffer_line_curposXYZE(400);
     }
@@ -7729,8 +7729,8 @@ Sigma_Exit:
     */
     case 302:
     {
-	  float temp = .0;
-	  if (code_seen('S')) temp=code_value();
+	  int temp = 0;
+	  if (code_seen('S')) temp=code_value_short();
       set_extrude_min_temp(temp);
     }
     break;
@@ -9679,7 +9679,7 @@ static uint16_t nFSCheckCount=0;
 #ifdef PAT9125
 					fsensor_autoload_check_stop();
 #endif //PAT9125
-//-//					if (degHotend0() > EXTRUDE_MINTEMP)
+//-//					if ((int)degHotend0() > extrude_min_temp)
 if(0)
 					{
 						Sound_MakeCustom(50,1000,false);
@@ -9695,7 +9695,7 @@ if(0)
 */
 						eFilamentAction=FilamentAction::AutoLoad;
 						bFilamentFirstRun=false;
-						if(target_temperature[0]>=EXTRUDE_MINTEMP){
+						if(target_temperature[0] >= extrude_min_temp){
 							bFilamentPreheatState=true;
 //							mFilamentItem(target_temperature[0],target_temperature_bed);
 							menu_submenu(mFilamentItemForce);
@@ -10620,7 +10620,7 @@ static void temp_compensation_start() {
 	custom_message_type = CustomMsg::TempCompPreheat;
 	custom_message_state = PINDA_HEAT_T + 1;
 	lcd_update(2);
-	if (degHotend(active_extruder) > EXTRUDE_MINTEMP) {
+	if ((int)degHotend(active_extruder) > extrude_min_temp) {
 		current_position[E_AXIS] -= default_retraction;
 	}
 	plan_buffer_line_curposXYZE(400, active_extruder);

Firmware/planner.cpp

@@ -122,7 +122,7 @@ static uint8_t g_cntr_planner_queue_min = 0;
 //=============================private variables ============================
 //===========================================================================
 #ifdef PREVENT_DANGEROUS_EXTRUDE
-float extrude_min_temp=EXTRUDE_MINTEMP;
+int extrude_min_temp = EXTRUDE_MINTEMP;
 #endif
 
 #ifdef LIN_ADVANCE
@@ -833,7 +833,7 @@ void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate
   #ifdef PREVENT_DANGEROUS_EXTRUDE
   if(target[E_AXIS]!=position[E_AXIS])
   {
-    if(degHotend(active_extruder)<extrude_min_temp)
+    if((int)degHotend(active_extruder)<extrude_min_temp)
     {
       position[E_AXIS]=target[E_AXIS]; //behave as if the move really took place, but ignore E part
       #ifdef LIN_ADVANCE
@@ -1434,9 +1434,9 @@ void plan_reset_next_e()
 }
 
 #ifdef PREVENT_DANGEROUS_EXTRUDE
-void set_extrude_min_temp(float temp)
+void set_extrude_min_temp(int temp)
 {
-  extrude_min_temp=temp;
+  extrude_min_temp = temp;
 }
 #endif
 

Firmware/planner.h

@@ -262,7 +262,8 @@ extern void planner_abort_hard();
 extern bool waiting_inside_plan_buffer_line_print_aborted;
 
 #ifdef PREVENT_DANGEROUS_EXTRUDE
-void set_extrude_min_temp(float temp);
+extern int extrude_min_temp;
+void set_extrude_min_temp(int temp);
 #endif
 
 void reset_acceleration_rates();

Firmware/ultralcd.cpp

@@ -2312,7 +2312,7 @@ static void lcd_menu_AutoLoadFilament()
 static void preheat_or_continue()
 {
     bFilamentFirstRun = false;
-    if (target_temperature[0] >= EXTRUDE_MINTEMP)
+    if (target_temperature[0] >= extrude_min_temp)
     {
         bFilamentPreheatState = true;
         mFilamentItem(target_temperature[0], target_temperature_bed);
@@ -2445,7 +2445,7 @@ static void _lcd_move(const char *name, uint8_t axis, int min, int max)
 
 void lcd_move_e()
 {
-	if (degHotend0() > EXTRUDE_MINTEMP)
+	if ((int)degHotend0() > extrude_min_temp)
 	{
 		if (lcd_encoder != 0)
 		{
@@ -5555,7 +5555,7 @@ static void mmu_cut_filament_menu()
     {
         eFilamentAction=FilamentAction::MmuCut;
         bFilamentFirstRun=false;
-        if(target_temperature[0]>=EXTRUDE_MINTEMP)
+        if(target_temperature[0] >= extrude_min_temp)
         {
             bFilamentPreheatState=true;
             mFilamentItem(target_temperature[0],target_temperature_bed);