Browse Source

conditional compilation updated

PavelSindler 5 years ago
parent
commit
6b1cf99066
3 changed files with 22 additions and 20 deletions
  1. 2 2
      Firmware/Marlin_main.cpp
  2. 18 16
      Firmware/fsensor.cpp
  3. 2 2
      Firmware/fsensor.h

+ 2 - 2
Firmware/Marlin_main.cpp

@@ -1481,9 +1481,9 @@ void setup()
 	setup_fan_interrupt();
 #endif //DEBUG_DISABLE_FANCHECK
 
-#ifdef FILAMENT_SENSOR
+#ifdef PAT9125
 	fsensor_setup_interrupt();
-#endif //FILAMENT_SENSOR
+#endif //PAT9125
 	for (int i = 0; i<4; i++) EEPROM_read_B(EEPROM_BOWDEN_LENGTH + i * 2, &bowden_length[i]); 
 	
 #ifndef DEBUG_DISABLE_STARTMSGS

+ 18 - 16
Firmware/fsensor.cpp

@@ -388,7 +388,7 @@ bool fsensor_oq_result(void)
 	printf_P(_N("fsensor_oq_result %S\n"), (res?_OK:_NG));
 	return res;
 }
-
+#ifdef PAT9125
 ISR(FSENSOR_INT_PIN_VECT)
 {
 	if (mmu_enabled || ir_sensor_detected) return;
@@ -475,6 +475,23 @@ ISR(FSENSOR_INT_PIN_VECT)
 	return;
 }
 
+void fsensor_setup_interrupt(void)
+{
+
+	pinMode(FSENSOR_INT_PIN, OUTPUT);
+	digitalWrite(FSENSOR_INT_PIN, LOW);
+	fsensor_int_pin_old = 0;
+
+	//pciSetup(FSENSOR_INT_PIN);
+// !!! "pciSetup()" does not provide the correct results for some MCU pins
+// so interrupt registers settings:
+     FSENSOR_INT_PIN_PCMSK_REG |= bit(FSENSOR_INT_PIN_PCMSK_BIT); // enable corresponding PinChangeInterrupt (individual pin)
+     PCIFR |= bit(FSENSOR_INT_PIN_PCICR_BIT);     // clear previous occasional interrupt (set of pins)
+     PCICR |= bit(FSENSOR_INT_PIN_PCICR_BIT);     // enable corresponding PinChangeInterrupt (set of pins)
+}
+
+#endif //PAT9125
+
 void fsensor_st_block_begin(block_t* bl)
 {
 	if (!fsensor_enabled) return;
@@ -569,18 +586,3 @@ void fsensor_update(void)
 		}
 #endif //PAT9125
 }
-
-void fsensor_setup_interrupt(void)
-{
-
-	pinMode(FSENSOR_INT_PIN, OUTPUT);
-	digitalWrite(FSENSOR_INT_PIN, LOW);
-	fsensor_int_pin_old = 0;
-
-	//pciSetup(FSENSOR_INT_PIN);
-// !!! "pciSetup()" does not provide the correct results for some MCU pins
-// so interrupt registers settings:
-     FSENSOR_INT_PIN_PCMSK_REG |= bit(FSENSOR_INT_PIN_PCMSK_BIT); // enable corresponding PinChangeInterrupt (individual pin)
-     PCIFR |= bit(FSENSOR_INT_PIN_PCICR_BIT);     // clear previous occasional interrupt (set of pins)
-     PCICR |= bit(FSENSOR_INT_PIN_PCICR_BIT);     // enable corresponding PinChangeInterrupt (set of pins)
-}

+ 2 - 2
Firmware/fsensor.h

@@ -35,13 +35,13 @@ extern bool fsensor_autoload_enabled;
 extern void fsensor_autoload_set(bool State);
 
 extern void fsensor_update(void);
-
+#ifdef PAT9125
 //! setup pin-change interrupt
 extern void fsensor_setup_interrupt(void);
 
 //! @name autoload support
 //! @{
-#ifdef PAT9125
+
 extern void fsensor_autoload_check_start(void);
 extern void fsensor_autoload_check_stop(void);
 #endif //PAT9125