Merge pull request #810 from PavelSindler/octoprint_features

Improve crash detection and filament detection when printing from USB

Firmware/Marlin_main.cpp

@@ -116,6 +116,9 @@
 //Macro for print fan speed
 #define FAN_PULSE_WIDTH_LIMIT ((fanSpeed > 100) ? 3 : 4) //time in ms
 
+#define PRINTING_TYPE_SD 0
+#define PRINTING_TYPE_USB 1
+
 // look here for descriptions of G-codes: http://linuxcnc.org/handbook/gcode/g-code.html
 // http://objects.reprap.org/wiki/Mendel_User_Manual:_RepRapGCodes
 
@@ -483,6 +486,7 @@ boolean chdkActive = false;
 
 // save/restore printing
 static uint32_t saved_sdpos = 0;
+static uint8_t saved_printing_type = PRINTING_TYPE_SD;
 static float saved_pos[4] = { 0, 0, 0, 0 };
 // Feedrate hopefully derived from an active block of the planner at the time the print has been canceled, in mm/min.
 static float saved_feedrate2 = 0;
@@ -626,12 +630,12 @@ void crashdet_disable()
 
 void crashdet_stop_and_save_print()
 {
-	stop_and_save_print_to_ram(10, 0); //XY - no change, Z 10mm up, E - no change
+	stop_and_save_print_to_ram(10, -2); //XY - no change, Z 10mm up, E -2mm retract
 }
 
 void crashdet_restore_print_and_continue()
 {
-	restore_print_from_ram_and_continue(0); //XYZ = orig, E - no change
+	restore_print_from_ram_and_continue(2); //XYZ = orig, E +2mm unretract
 //	babystep_apply();
 }
 
@@ -1732,7 +1736,15 @@ void loop()
           planner_add_sd_length(sdlen.value);
           sei();
         }
-      }
+	  }
+	  else if((*ptr == CMDBUFFER_CURRENT_TYPE_USB_WITH_LINENR) && !IS_SD_PRINTING){ 
+		  
+		  cli();
+          *ptr ++ = CMDBUFFER_CURRENT_TYPE_TO_BE_REMOVED;
+          // and one for each command to previous block in the planner queue.
+          planner_add_sd_length(1);
+          sei();
+	  }
       // Now it is safe to release the already processed command block. If interrupted by the power panic now,
       // this block's SD card length will not be counted twice as its command type has been replaced 
       // by CMDBUFFER_CURRENT_TYPE_TO_BE_REMOVED.
@@ -6933,7 +6945,7 @@ void FlushSerialRequestResend()
 void ClearToSend()
 {
     previous_millis_cmd = millis();
-    if (CMDBUFFER_CURRENT_TYPE == CMDBUFFER_CURRENT_TYPE_USB)
+    if ((CMDBUFFER_CURRENT_TYPE == CMDBUFFER_CURRENT_TYPE_USB) || (CMDBUFFER_CURRENT_TYPE == CMDBUFFER_CURRENT_TYPE_USB_WITH_LINENR))
         SERIAL_PROTOCOLLNRPGM(_T(MSG_OK));
 }
 
@@ -8496,13 +8508,34 @@ void restore_print_from_eeprom() {
 void stop_and_save_print_to_ram(float z_move, float e_move)
 {
 	if (saved_printing) return;
+	unsigned char nplanner_blocks;
+	unsigned char nlines;
+	uint16_t sdlen_planner;
+	uint16_t sdlen_cmdqueue;
+	
+
 	cli();
-  unsigned char nplanner_blocks = number_of_blocks();
-	saved_sdpos = sdpos_atomic; //atomic sd position of last command added in queue
-	uint16_t sdlen_planner = planner_calc_sd_length(); //length of sd commands in planner
-	saved_sdpos -= sdlen_planner;
-	uint16_t sdlen_cmdqueue = cmdqueue_calc_sd_length(); //length of sd commands in cmdqueue
-	saved_sdpos -= sdlen_cmdqueue;
+	if (card.sdprinting) {
+		nplanner_blocks = number_of_blocks();
+		saved_sdpos = sdpos_atomic; //atomic sd position of last command added in queue
+		sdlen_planner = planner_calc_sd_length(); //length of sd commands in planner
+		saved_sdpos -= sdlen_planner;
+		sdlen_cmdqueue = cmdqueue_calc_sd_length(); //length of sd commands in cmdqueue
+		saved_sdpos -= sdlen_cmdqueue;
+		saved_printing_type = PRINTING_TYPE_SD;
+
+	}
+	else if (is_usb_printing) { //reuse saved_sdpos for storing line number
+		 saved_sdpos = gcode_LastN; //start with line number of command added recently to cmd queue
+		 //reuse planner_calc_sd_length function for getting number of lines of commands in planner:
+		 nlines = planner_calc_sd_length(); //number of lines of commands in planner 
+		 saved_sdpos -= nlines;
+		 saved_sdpos -= buflen; //number of blocks in cmd buffer
+		 saved_printing_type = PRINTING_TYPE_USB;
+	}
+	else {
+		//not sd printing nor usb printing
+	}
 
 #if 0
   SERIAL_ECHOPGM("SDPOS_ATOMIC="); MYSERIAL.println(sdpos_atomic, DEC);
@@ -8511,7 +8544,8 @@ void stop_and_save_print_to_ram(float z_move, float e_move)
   SERIAL_ECHOPGM("SDLEN_CMDQ="); MYSERIAL.println(sdlen_cmdqueue, DEC);
   SERIAL_ECHOPGM("PLANNERBLOCKS="); MYSERIAL.println(int(nplanner_blocks), DEC);
   SERIAL_ECHOPGM("SDSAVED="); MYSERIAL.println(saved_sdpos, DEC);
-  SERIAL_ECHOPGM("SDFILELEN="); MYSERIAL.println(card.fileSize(), DEC);
+  //SERIAL_ECHOPGM("SDFILELEN="); MYSERIAL.println(card.fileSize(), DEC);
+
 
   {
     card.setIndex(saved_sdpos);
@@ -8523,7 +8557,6 @@ void stop_and_save_print_to_ram(float z_move, float e_move)
       MYSERIAL.print(char(card.get()));
     SERIAL_ECHOLNPGM("End of command buffer");
   }
-
   {
     // Print the content of the planner buffer, line by line:
     card.setIndex(saved_sdpos);
@@ -8618,11 +8651,17 @@ void stop_and_save_print_to_ram(float z_move, float e_move)
 #if 1
     // Rather than calling plan_buffer_line directly, push the move into the command queue, 
     char buf[48];
+
+	// First unretract (relative extrusion)
+	strcpy_P(buf, PSTR("G1 E"));
+	dtostrf(e_move, 6, 3, buf + strlen(buf));
+	strcat_P(buf, PSTR(" F"));
+	dtostrf(retract_feedrate*60, 8, 3, buf + strlen(buf));
+	enquecommand(buf, false);
+
+	// Then lift Z axis
     strcpy_P(buf, PSTR("G1 Z"));
     dtostrf(saved_pos[Z_AXIS] + z_move, 8, 3, buf + strlen(buf));
-    strcat_P(buf, PSTR(" E"));
-    // Relative extrusion
-    dtostrf(e_move, 6, 3, buf + strlen(buf));
     strcat_P(buf, PSTR(" F"));
     dtostrf(homing_feedrate[Z_AXIS], 8, 3, buf + strlen(buf));
     // At this point the command queue is empty.
@@ -8649,14 +8688,23 @@ void restore_print_from_ram_and_continue(float e_move)
 	float e = saved_pos[E_AXIS] - e_move;
 	plan_set_e_position(e);
 	plan_buffer_line(saved_pos[X_AXIS], saved_pos[Y_AXIS], saved_pos[Z_AXIS], saved_pos[E_AXIS], homing_feedrate[Z_AXIS]/13, active_extruder);
-    st_synchronize();
-  memcpy(current_position, saved_pos, sizeof(saved_pos));
-  memcpy(destination, current_position, sizeof(destination));
-	card.setIndex(saved_sdpos);
-  sdpos_atomic = saved_sdpos;
-	card.sdprinting = true;
+	st_synchronize();
+	memcpy(current_position, saved_pos, sizeof(saved_pos));
+	memcpy(destination, current_position, sizeof(destination));
+	if (saved_printing_type == PRINTING_TYPE_SD) { //was sd printing
+		card.setIndex(saved_sdpos);
+		sdpos_atomic = saved_sdpos;
+		card.sdprinting = true;
+	}
+	else if (saved_printing_type == PRINTING_TYPE_USB) { //was usb printing
+		gcode_LastN = saved_sdpos; //saved_sdpos was reused for storing line number when usb printing
+		FlushSerialRequestResend();
+	}
+	else {
+		//not sd printing nor usb printing
+	}
 	saved_printing = false;
-	printf_P(PSTR("ok\n")); //dummy response because of octoprint is waiting for this
+	
 }
 
 void print_world_coordinates()

Firmware/cmdqueue.cpp

@@ -386,7 +386,7 @@ void get_command()
 	}
 
   while (MYSERIAL.available() > 0) {
-
+	
     char serial_char = MYSERIAL.read();
 /*    if (selectedSerialPort == 1)
     {
@@ -413,6 +413,9 @@ void get_command()
       }
       cmdbuffer[bufindw+serial_count+CMDHDRSIZE] = 0; //terminate string
       if(!comment_mode){
+		  
+		  gcode_N = 0;
+
 		  // Line numbers must be first in buffer
 
 		  if ((strstr(cmdbuffer+bufindw+CMDHDRSIZE, "PRUSA") == NULL) &&
@@ -494,7 +497,8 @@ void get_command()
           kill("", 2);
         
         // Store the current line into buffer, move to the next line.
-        cmdbuffer[bufindw] = CMDBUFFER_CURRENT_TYPE_USB; 
+		// Store type of entry
+        cmdbuffer[bufindw] = gcode_N ? CMDBUFFER_CURRENT_TYPE_USB_WITH_LINENR : CMDBUFFER_CURRENT_TYPE_USB;
 #ifdef CMDBUFFER_DEBUG
         SERIAL_ECHO_START;
         SERIAL_ECHOPGM("Storing a command line to buffer: ");

Firmware/cmdqueue.h

@@ -22,6 +22,8 @@
 // to the planner queue, but not yet removed from the cmdqueue. 
 // This is a temporary state to reduce stepper interrupt locking time.
 #define CMDBUFFER_CURRENT_TYPE_TO_BE_REMOVED 5
+//Command in cmdbuffer was sent over USB and contains line number
+#define CMDBUFFER_CURRENT_TYPE_USB_WITH_LINENR 6
 
 // How much space to reserve for the chained commands
 // of type CMDBUFFER_CURRENT_TYPE_CHAINED,

Firmware/ultralcd_implementation_hitachi_HD44780.h

@@ -830,8 +830,12 @@ if (print_sd_status)
 #endif
 	}
 
-
-
+#ifdef CMD_DIAGNOSTICS
+	lcd.setCursor(LCD_WIDTH - 8 -1, 2);
+	lcd_printPGM(PSTR("      C"));
+	lcd.print(buflen);	// number of commands in cmd buffer
+	if (buflen < 9) lcd_printPGM(" ");
+#else
     //Print time elapsed
     lcd.setCursor(LCD_WIDTH - 8 -1, 2);
     lcd_printPGM(PSTR(" "));
@@ -846,6 +850,7 @@ if (print_sd_status)
         lcd_printPGM(PSTR("--:--"));
     }
     lcd_printPGM(PSTR("  "));
+#endif //CMD_DIAGNOSTICS
 
 #ifdef DEBUG_DISABLE_LCD_STATUS_LINE
 	return;