Revert "Mesh bed leveling testing"

This reverts commit 28e812d91fe2b4633c9427abdf554e5a9449dd17.

Firmware/Marlin_main.cpp

@@ -4973,7 +4973,11 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 					z_offset_u = eeprom_read_word((uint16_t*)(EEPROM_BED_CALIBRATION_Z_JITTER + 2 * (ix + iy * 3 - 1)));
 				}
 				z0 = mbl.z_values[0][0] + *reinterpret_cast<int16_t*>(&z_offset_u) * 0.01;
-				// printf_P(PSTR("Bed leveling, point: %d, calibration Z stored in eeprom: %d, calibration z: %f \n"), mesh_point, z_offset_u, z0);
+				#ifdef SUPPORT_VERBOSITY
+				if (verbosity_level >= 1) {
+					printf_P(PSTR("Bed leveling, point: %d, calibration Z stored in eeprom: %d, calibration z: %f \n"), mesh_point, z_offset_u, z0);
+				}
+				#endif // SUPPORT_VERBOSITY
 			}
 
 			// Move Z up to MESH_HOME_Z_SEARCH.
@@ -5000,7 +5004,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 				world2machine_clamp(current_position[X_AXIS], current_position[Y_AXIS]);
 			#endif // SUPPORT_VERBOSITY
 
-			printf_P(PSTR("after clamping: [%f;%f]\n"), current_position[X_AXIS], current_position[Y_AXIS]);
+			//printf_P(PSTR("after clamping: [%f;%f]\n"), current_position[X_AXIS], current_position[Y_AXIS]);
 			plan_buffer_line_curposXYZE(XY_AXIS_FEEDRATE, active_extruder);
 			st_synchronize();
 
@@ -5011,7 +5015,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 				break;
 			}
 			if (init_z_bckp - current_position[Z_AXIS] < 0.1f) { //broken cable or initial Z coordinate too low. Go to MESH_HOME_Z_SEARCH and repeat last step (z-probe) again to distinguish between these two cases.
-				printf_P(PSTR("Another attempt! Current Z position: %f\n"), current_position[Z_AXIS]);
+				//printf_P(PSTR("Another attempt! Current Z position: %f\n"), current_position[Z_AXIS]);
 				current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
 				plan_buffer_line_curposXYZE(Z_LIFT_FEEDRATE, active_extruder);
 				st_synchronize();

Firmware/mesh_bed_calibration.cpp

@@ -991,7 +991,7 @@ inline bool find_bed_induction_sensor_point_z(float minimum_z, uint8_t n_iter, i
         update_current_position_z();
 		//printf_P(PSTR("Zs: %f, Z: %f, delta Z: %f"), z_bckp, current_position[Z_AXIS], (z_bckp - current_position[Z_AXIS]));
 		if (abs(current_position[Z_AXIS] - z_bckp) < 0.025) {
-			printf_P(PSTR("PINDA triggered immediately, move Z higher and repeat measurement\n")); 
+			//printf_P(PSTR("PINDA triggered immediately, move Z higher and repeat measurement\n")); 
 			current_position[Z_AXIS] += 0.5;
 			go_to_current(homing_feedrate[Z_AXIS]/60);
 			current_position[Z_AXIS] = minimum_z;
@@ -1019,10 +1019,10 @@ inline bool find_bed_induction_sensor_point_z(float minimum_z, uint8_t n_iter, i
 		float dz = i?abs(current_position[Z_AXIS] - (z / i)):0;
         z += current_position[Z_AXIS];
 		//printf_P(PSTR("Z[%d] = %d, dz=%d\n"), i, (int)(current_position[Z_AXIS] * 1000), (int)(dz * 1000));
-		printf_P(PSTR("Z- measurement deviation from avg value %f um\n"), dz);
+		//printf_P(PSTR("Z- measurement deviation from avg value %f um\n"), dz);
 		if (dz > 0.05) { //deviation > 50um
 			if (high_deviation_occured == false) { //first occurence may be caused in some cases by mechanic resonance probably especially if printer is placed on unstable surface 
-				printf_P(PSTR("high dev. first occurence\n"));
+				//printf_P(PSTR("high dev. first occurence\n"));
 				delay_keep_alive(500); //damping
 				//start measurement from the begining, but this time with higher movements in Z axis which should help to reduce mechanical resonance
 				high_deviation_occured = true;
@@ -1033,7 +1033,7 @@ inline bool find_bed_induction_sensor_point_z(float minimum_z, uint8_t n_iter, i
 				goto error;
 			}
 		}
-		printf_P(PSTR("PINDA triggered at %f\n"), current_position[Z_AXIS]);
+		//printf_P(PSTR("PINDA triggered at %f\n"), current_position[Z_AXIS]);
     }
     current_position[Z_AXIS] = z;
     if (n_iter > 1)