Merge pull request #2470 from leptun/MK3_Adjusted_mintemp

Adjusted hotend, bed and Ambient mintemp values

Firmware/variants/1_75mm_MK3-EINSy10a-E3Dv6full.h

@@ -151,8 +151,8 @@
 // this value is litlebit higher that real limit, because ambient termistor is on the board and is temperated from it,
 // temperature inside the case is around 31C for ambient temperature 25C, when the printer is powered on long time and idle
 // the real limit is 15C (same as MINTEMP limit), this is because 15C is end of scale for both used thermistors (bed, heater)
-#define MINTEMP_MINAMBIENT      25
-#define MINTEMP_MINAMBIENT_RAW  978
+#define MINTEMP_MINAMBIENT      10
+#define MINTEMP_MINAMBIENT_RAW  1002
 
 #define DEBUG_DCODE3
 
@@ -282,14 +282,14 @@
  *------------------------------------*/
 
 // Mintemps
-#define HEATER_0_MINTEMP 15
+#define HEATER_0_MINTEMP 10
 #define HEATER_1_MINTEMP 5
 #define HEATER_2_MINTEMP 5
 #define HEATER_MINTEMP_DELAY 15000                // [ms] ! if changed, check maximal allowed value @ ShortTimer
 #if HEATER_MINTEMP_DELAY>USHRT_MAX
 #error "Check maximal allowed value @ ShortTimer (see HEATER_MINTEMP_DELAY definition)"
 #endif
-#define BED_MINTEMP 15
+#define BED_MINTEMP 10
 #define BED_MINTEMP_DELAY 50000                   // [ms] ! if changed, check maximal allowed value @ ShortTimer
 #if BED_MINTEMP_DELAY>USHRT_MAX
 #error "Check maximal allowed value @ ShortTimer (see BED_MINTEMP_DELAY definition)"

Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h

@@ -153,8 +153,8 @@
 // this value is litlebit higher that real limit, because ambient termistor is on the board and is temperated from it,
 // temperature inside the case is around 31C for ambient temperature 25C, when the printer is powered on long time and idle
 // the real limit is 15C (same as MINTEMP limit), this is because 15C is end of scale for both used thermistors (bed, heater)
-#define MINTEMP_MINAMBIENT      25
-#define MINTEMP_MINAMBIENT_RAW  978
+#define MINTEMP_MINAMBIENT      10
+#define MINTEMP_MINAMBIENT_RAW  1002
 
 #define DEBUG_DCODE3
 
@@ -284,14 +284,14 @@
  *------------------------------------*/
 
 // Mintemps
-#define HEATER_0_MINTEMP 15
+#define HEATER_0_MINTEMP 10
 #define HEATER_1_MINTEMP 5
 #define HEATER_2_MINTEMP 5
 #define HEATER_MINTEMP_DELAY 15000                // [ms] ! if changed, check maximal allowed value @ ShortTimer
 #if HEATER_MINTEMP_DELAY>USHRT_MAX
 #error "Check maximal allowed value @ ShortTimer (see HEATER_MINTEMP_DELAY definition)"
 #endif
-#define BED_MINTEMP 15
+#define BED_MINTEMP 10
 #define BED_MINTEMP_DELAY 50000                   // [ms] ! if changed, check maximal allowed value @ ShortTimer
 #if BED_MINTEMP_DELAY>USHRT_MAX
 #error "Check maximal allowed value @ ShortTimer (see BED_MINTEMP_DELAY definition)"