Merge pull request #469 from XPila/MK25

fix - conditional translation for DEBUG build

Firmware/Configuration_prusa.h

@@ -101,7 +101,7 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 //#define DEBUG_DISABLE_YMAXLIMIT  //y max limit ignored
 //#define DEBUG_DISABLE_ZMINLIMIT  //z min limit ignored
 //#define DEBUG_DISABLE_ZMAXLIMIT  //z max limit ignored
-#define DEBUG_DISABLE_STARTMSGS //no startup messages 
+//#define DEBUG_DISABLE_STARTMSGS //no startup messages 
 //#define DEBUG_DISABLE_MINTEMP   //mintemp error ignored
 //#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
 //#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
@@ -112,9 +112,9 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 //#define DEBUG_BLINK_ACTIVE
 //#define DEBUG_DISABLE_FANCHECK     //disable fan check (no ISR INT7, check disabled)
 //#define DEBUG_DISABLE_FSENSORCHECK //disable fsensor check (no ISR INT7, check disabled)
-#define DEBUG_DUMP_TO_2ND_SERIAL   //dump received characters to 2nd serial line
-#define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message.
-#define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display.
+//#define DEBUG_DUMP_TO_2ND_SERIAL   //dump received characters to 2nd serial line
+//#define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message.
+//#define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display.
 #endif /* DEBUG_BUILD */
 
 

Firmware/Dcodes.cpp

@@ -400,6 +400,7 @@ extern int current_temperature_raw_pinda;
 extern int current_temperature_raw_ambient;
 extern int current_voltage_raw_pwr;
 extern int current_voltage_raw_bed;
+
 uint16_t dcode_9_ADC_val(uint8_t i)
 {
 	switch (i)
@@ -408,9 +409,13 @@ uint16_t dcode_9_ADC_val(uint8_t i)
 	case 1: return 0;
 	case 2: return current_temperature_bed_raw;
 	case 3: return current_temperature_raw_pinda;
+#ifdef VOLT_PWR_PIN
 	case 4: return current_voltage_raw_pwr;
-	case 5: return current_temperature_raw_ambient;
 	case 6: return current_voltage_raw_bed;
+#endif //VOLT_PWR_PIN
+#ifdef AMBIENT_THERMISTOR
+	case 5: return current_temperature_raw_ambient;
+#endif //AMBIENT_THERMISTOR
 	}
 	return 0;
 }
@@ -454,11 +459,11 @@ void dcode_12()
     eeprom_update_byte((uint8_t*)EEPROM_POWER_COUNT, 0x00);
 }
 
-#include "tmc2130.h"
-#include "Marlin.h"
+
+#ifdef TMC2130
 #include "planner.h"
 extern void st_synchronize();
-
+#include "tmc2130.h"
 void dcode_2130()
 {
 //	printf("test");
@@ -485,7 +490,9 @@ void dcode_2130()
 		printf_P(PSTR("Meassure avg = %d\n"), sg);
 	}
 }
+#endif //TMC2130
 
+#ifdef PAT9125
 void dcode_9125()
 {
 	LOG("D9125 - PAT9125\n");
@@ -524,5 +531,7 @@ void dcode_9125()
 		LOG("fsensor_log=%d\n", fsensor_log);
 	}
 }
+#endif //PAT9125
+
 
 #endif //DEBUG_DCODES

Firmware/Dcodes.h

@@ -17,7 +17,13 @@ extern void dcode_9(); //D9 - Read/Write ADC (Write=enable simulated, Read=disab
 extern void dcode_10(); //D10 - XYZ calibration = OK
 extern void dcode_12(); //D12 - Reset failstat counters
 
+#ifdef TMC2130
 extern void dcode_2130(); //D2130 - TMC2130
+#endif //TMC2130
+
+#ifdef PAT9125
 extern void dcode_9125(); //D9125 - PAT9125
+#endif //PAT9125
+
 
 #endif //DCODES_H

Firmware/Marlin_main.cpp

@@ -6401,10 +6401,16 @@ case 404:  //M404 Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or disp
     case 12: //D12 - Reset failstat counters
 		dcode_12(); break;
 
+#ifdef TMC2130
 	case 2130: // D9125 - TMC2130
 		dcode_2130(); break;
+#endif //TMC2130
+
+#ifdef PAT9125
 	case 9125: // D9125 - PAT9125
 		dcode_9125(); break;
+#endif //PAT9125
+
 	}
   }
 #endif //DEBUG_DCODES