Merge pull request #122 from XPila/MK3s_upg

Mk3s upg

Firmware/Configuration.h

@@ -477,7 +477,8 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM_BITS 4 //PWM bit resolution = 4bits, freq = 62.5Hz
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.

Firmware/Marlin_main.cpp

@@ -974,6 +974,10 @@ void setup()
 	
 	ultralcd_init();
 
+#if (LCD_BL_PIN != -1)
+	analogWrite(LCD_BL_PIN, 255); //set full brightnes
+#endif //(LCD_BL_PIN != -1)
+
 	spi_init();
 
 	lcd_splash();
@@ -1809,6 +1813,15 @@ void loop()
   isPrintPaused ? manage_inactivity(true) : manage_inactivity(false);
   checkHitEndstops();
   lcd_update(0);
+#ifdef NEW_FILAMENT_SENSOR
+	if (mcode_in_progress != 600 && !mmu_enabled) //M600 not in progress
+	{
+		if (IS_SD_PRINTING)
+		{
+			fsensor_update();
+		}
+	}
+#endif //NEW_FILAMENT_SENSOR
 #ifdef TMC2130
 	tmc2130_check_overtemp();
 	if (tmc2130_sg_crash)

Firmware/fsensor.cpp

@@ -477,6 +477,18 @@ void fsensor_st_block_chunk(block_t* bl, int cnt)
 //! If there is still no plausible signal from filament sensor plans M600 (Filament change).
 void fsensor_update(void)
 {
+#ifdef NEW_FILAMENT_SENSOR
+	if (digitalRead(A8) == 1)
+	{
+		fsensor_stop_and_save_print();
+		printf_P(PSTR("fsensor_update - M600\n"));
+		eeprom_update_byte((uint8_t*)EEPROM_FERROR_COUNT, eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT) + 1);
+		eeprom_update_word((uint16_t*)EEPROM_FERROR_COUNT_TOT, eeprom_read_word((uint16_t*)EEPROM_FERROR_COUNT_TOT) + 1);
+		enquecommand_front_P(PSTR("FSENSOR_RECOVER"));
+		enquecommand_front_P((PSTR("M600")));
+		fsensor_watch_runout = false;
+	}
+#else //NEW_FILAMENT_SENSOR
 	if (fsensor_enabled && fsensor_watch_runout && (fsensor_err_cnt > FSENSOR_ERR_MAX))
 	{
         bool autoload_enabled_tmp = fsensor_autoload_enabled;
@@ -527,6 +539,7 @@ void fsensor_update(void)
         fsensor_autoload_enabled = autoload_enabled_tmp;
 		fsensor_oq_meassure_enabled = oq_meassure_enabled_tmp;
 	}
+#endif //NEW_FILAMENT_SENSOR
 }
 
 void fsensor_setup_interrupt(void)

Firmware/pins_Einsy_1_0.h

@@ -99,10 +99,7 @@
 
 //#define KILL_PIN            32
 
-
-//#define LCD_PWM_PIN         -1//32  // lcd backlight brightnes pwm control pin
-//#define LCD_PWM_MAX       0x0f  // lcd pwm maximum value (0x07=64Hz, 0x0f=32Hz, 0x1f=16Hz)
-
+#define LCD_BL_PIN          5   //backlight control pin
 #define BEEPER              84  // Beeper on AUX-4
 #define LCD_PINS_RS         82
 #define LCD_PINS_ENABLE     61 // !!! changed from 18 (EINY03)

Firmware/temperature.cpp

@@ -1024,7 +1024,7 @@ void tp_init()
     setPwmFrequency(FAN_PIN, 1); // No prescaling. Pwm frequency = F_CPU/256/8
     #endif
     #ifdef FAN_SOFT_PWM
-    soft_pwm_fan = fanSpeedSoftPwm / 2;
+    soft_pwm_fan = fanSpeedSoftPwm / (1 << (8 - FAN_SOFT_PWM_BITS));
     #endif
   #endif
 
@@ -1600,11 +1600,14 @@ ISR(TIMER0_COMPB_vect)
     soft_pwm_b = soft_pwm_bed;
     if(soft_pwm_b > 0) WRITE(HEATER_BED_PIN,1); else WRITE(HEATER_BED_PIN,0);
 #endif
+  }
 #ifdef FAN_SOFT_PWM
-    soft_pwm_fan = fanSpeedSoftPwm / 2;
+  if ((pwm_count & ((1 << FAN_SOFT_PWM_BITS) - 1)) == 0)
+  {
+    soft_pwm_fan = fanSpeedSoftPwm / (1 << (8 - FAN_SOFT_PWM_BITS));
     if(soft_pwm_fan > 0) WRITE(FAN_PIN,1); else WRITE(FAN_PIN,0);
-#endif
   }
+#endif
   if(soft_pwm_0 < pwm_count)
   { 
     WRITE(HEATER_0_PIN,0);
@@ -1623,7 +1626,7 @@ ISR(TIMER0_COMPB_vect)
   if(soft_pwm_b < pwm_count) WRITE(HEATER_BED_PIN,0);
 #endif
 #ifdef FAN_SOFT_PWM
-  if(soft_pwm_fan < pwm_count) WRITE(FAN_PIN,0);
+  if (soft_pwm_fan < (pwm_count & ((1 << FAN_SOFT_PWM_BITS) - 1))) WRITE(FAN_PIN,0);
 #endif
   
   pwm_count += (1 << SOFT_PWM_SCALE);
@@ -1810,8 +1813,8 @@ ISR(TIMER0_COMPB_vect)
 #endif
   
 #ifdef FAN_SOFT_PWM
-  if (pwm_count == 0){
-    soft_pwm_fan = fanSpeedSoftPwm / 2;
+  if ((pwm_count & ((1 << FAN_SOFT_PWM_BITS) - 1)) == 0)
+    soft_pwm_fan = fanSpeedSoftPwm / (1 << (8 - FAN_SOFT_PWM_BITS));
     if (soft_pwm_fan > 0) WRITE(FAN_PIN,1); else WRITE(FAN_PIN,0);
   }
   if (soft_pwm_fan < pwm_count) WRITE(FAN_PIN,0);

Firmware/variants/1_75mm_MK3-EINSy10a-E3Dv6full.h

@@ -134,6 +134,7 @@
 // Filament sensor
 #define PAT9125
 #define FILAMENT_SENSOR
+//#define NEW_FILAMENT_SENSOR
 
 // Backlash - 
 //#define BACKLASH_X