Typo: meassure -> measure

Firmware/tmc2130.cpp

@@ -45,9 +45,9 @@ uint8_t tmc2130_sg_homing_axes_mask = 0x00;
 
 const char eMotorCurrentScalingEnabled[] PROGMEM = "E-motor current scaling enabled";
 
-uint8_t tmc2130_sg_meassure = 0xff;
-uint32_t tmc2130_sg_meassure_cnt = 0;
-uint32_t tmc2130_sg_meassure_val = 0;
+uint8_t tmc2130_sg_measure = 0xff;
+uint32_t tmc2130_sg_measure_cnt = 0;
+uint32_t tmc2130_sg_measure_val = 0;
 
 uint8_t tmc2130_home_enabled = 0;
 uint8_t tmc2130_home_origin[2] = {0, 0};
@@ -252,12 +252,12 @@ void tmc2130_st_isr()
 
 bool tmc2130_update_sg()
 {
-	if (tmc2130_sg_meassure <= E_AXIS)
+	if (tmc2130_sg_measure <= E_AXIS)
 	{
 		uint32_t val32 = 0;
-		tmc2130_rd(tmc2130_sg_meassure, TMC2130_REG_DRV_STATUS, &val32);
-		tmc2130_sg_meassure_val += (val32 & 0x3ff);
-		tmc2130_sg_meassure_cnt++;
+		tmc2130_rd(tmc2130_sg_measure, TMC2130_REG_DRV_STATUS, &val32);
+		tmc2130_sg_measure_val += (val32 & 0x3ff);
+		tmc2130_sg_measure_cnt++;
 		return true;
 	}
 	return false;
@@ -326,17 +326,17 @@ void tmc2130_home_exit()
 #endif
 }
 
-void tmc2130_sg_meassure_start(uint8_t axis)
+void tmc2130_sg_measure_start(uint8_t axis)
 {
-	tmc2130_sg_meassure = axis;
-	tmc2130_sg_meassure_cnt = 0;
-	tmc2130_sg_meassure_val = 0;
+	tmc2130_sg_measure = axis;
+	tmc2130_sg_measure_cnt = 0;
+	tmc2130_sg_measure_val = 0;
 }
 
-uint16_t tmc2130_sg_meassure_stop()
+uint16_t tmc2130_sg_measure_stop()
 {
-	tmc2130_sg_meassure = 0xff;
-	return tmc2130_sg_meassure_val / tmc2130_sg_meassure_cnt;
+	tmc2130_sg_measure = 0xff;
+	return tmc2130_sg_measure_val / tmc2130_sg_measure_cnt;
 }
 
 

Firmware/tmc2130.h

@@ -16,9 +16,9 @@ extern uint8_t tmc2130_sg_thr[4];
 extern bool tmc2130_sg_stop_on_crash;
 extern uint8_t tmc2130_sg_crash; //crash mask
 
-extern uint8_t tmc2130_sg_meassure;
-extern uint32_t tmc2130_sg_meassure_cnt;
-extern uint32_t tmc2130_sg_meassure_val;
+extern uint8_t tmc2130_sg_measure;
+extern uint32_t tmc2130_sg_measure_cnt;
+extern uint32_t tmc2130_sg_measure_val;
 
 extern uint8_t tmc2130_sg_homing_axes_mask;
 
@@ -94,9 +94,9 @@ extern void tmc2130_home_enter(uint8_t axes_mask);
 extern void tmc2130_home_exit();
 
 //start stallguard meassuring for single axis
-extern void tmc2130_sg_meassure_start(uint8_t axis);
+extern void tmc2130_sg_measure_start(uint8_t axis);
 //stop current stallguard meassuring and report result
-extern uint16_t tmc2130_sg_meassure_stop();
+extern uint16_t tmc2130_sg_measure_stop();
 
 extern void tmc2130_setup_chopper(uint8_t axis, uint8_t mres, uint8_t current_h, uint8_t current_r);
 

Firmware/ultralcd.cpp

@@ -1830,7 +1830,7 @@ void lcd_set_filament_autoload() {
 #if defined(FILAMENT_SENSOR) && defined(PAT9125)
 void lcd_set_filament_oq_meass()
 {
-     fsensor_oq_meassure_set(!fsensor_oq_meassure_enabled);
+     fsensor_oq_measure_set(!fsensor_oq_measure_enabled);
 }
 #endif
 
@@ -6524,7 +6524,7 @@ static bool lcd_selfcheck_axis_sg(uint8_t axis) {
 	
 	st_synchronize();
 
-	tmc2130_sg_meassure_start(axis);
+	tmc2130_sg_measure_start(axis);
 
 	current_position_init = st_get_position_mm(axis);
 
@@ -6537,7 +6537,7 @@ static bool lcd_selfcheck_axis_sg(uint8_t axis) {
 
 	st_synchronize();
 
-	uint16_t sg1 = tmc2130_sg_meassure_stop();
+	uint16_t sg1 = tmc2130_sg_measure_stop();
 	printf_P(PSTR("%c AXIS SG1=%d\n"), 'X'+axis, sg1);
 	eeprom_write_word(((uint16_t*)((axis == X_AXIS)?EEPROM_BELTSTATUS_X:EEPROM_BELTSTATUS_Y)), sg1);
 

Firmware/xyzcal.cpp

@@ -135,9 +135,9 @@ pos_mm_t pos_2_mm(float pos){
 	return pos * 0.01f;
 }
 
-void xyzcal_meassure_enter(void)
+void xyzcal_measure_enter(void)
 {
-	DBG(_n("xyzcal_meassure_enter\n"));
+	DBG(_n("xyzcal_measure_enter\n"));
 	lcd_puts_at_P(4,3,PSTR("Measure center  ")); ////MSG_MEASURE_CENTER c=16
 	// disable heaters and stop motion before we initialize sm4
 	disable_heater();
@@ -155,9 +155,9 @@ void xyzcal_meassure_enter(void)
 	sm4_calc_delay_cb = xyzcal_calc_delay;
 }
 
-void xyzcal_meassure_leave(void)
+void xyzcal_measure_leave(void)
 {
-	DBG(_n("xyzcal_meassure_leave\n"));
+	DBG(_n("xyzcal_measure_leave\n"));
 	lcd_set_cursor(4,3);
 	lcd_space(16);
 
@@ -344,7 +344,7 @@ bool xyzcal_spiral8(int16_t cx, int16_t cy, int16_t z0, int16_t dz, int16_t radi
 	return ret;
 }
 
-#ifdef XYZCAL_MEASSURE_PINDA_HYSTERESIS
+#ifdef XYZCAL_MEASURE_PINDA_HYSTERESIS
 int8_t xyzcal_measure_pinda_hysteresis(int16_t min_z, int16_t max_z, uint16_t delay_us, uint8_t samples)
 {
 	DBG(_n("xyzcal_measure_pinda_hysteresis\n"));
@@ -392,7 +392,7 @@ int8_t xyzcal_measure_pinda_hysteresis(int16_t min_z, int16_t max_z, uint16_t de
 	xyzcal_lineXYZ_to(_X, _Y, z, delay_us, 0);
 	return ret;
 }
-#endif //XYZCAL_MEASSURE_PINDA_HYSTERESIS
+#endif //XYZCAL_MEASURE_PINDA_HYSTERESIS
 
 void print_hysteresis(int16_t min_z, int16_t max_z, int16_t step){
 	int16_t delay_us = 600;
@@ -1006,10 +1006,10 @@ BedSkewOffsetDetectionResultType xyzcal_scan_and_process(){
 BedSkewOffsetDetectionResultType xyzcal_find_bed_induction_sensor_point_xy(void) {
     // DBG(_n("xyzcal_find_bed_induction_sensor_point_xy x=%ld y=%ld z=%ld\n"), count_position[X_AXIS], count_position[Y_AXIS], count_position[Z_AXIS]);
 	BedSkewOffsetDetectionResultType ret = BED_SKEW_OFFSET_DETECTION_POINT_NOT_FOUND;
-	xyzcal_meassure_enter();
+	xyzcal_measure_enter();
 	if (xyzcal_searchZ())
 		ret = xyzcal_scan_and_process();
-	xyzcal_meassure_leave();
+	xyzcal_measure_leave();
 	return ret;
 }
 

Firmware/xyzcal.h

@@ -5,8 +5,8 @@
 
 #include "mesh_bed_calibration.h"
 
-extern void xyzcal_meassure_enter(void);
-extern void xyzcal_meassure_leave(void);
+extern void xyzcal_measure_enter(void);
+extern void xyzcal_measure_leave(void);
 
 extern bool xyzcal_lineXYZ_to(int16_t x, int16_t y, int16_t z, uint16_t delay_us, int8_t check_pinda);