DEBUG defines, variant files for MK3

Firmware/Configuration.h

@@ -171,6 +171,11 @@
 //if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
 #define PREVENT_LENGTHY_EXTRUDE
 
+#ifdef DEBUG_DISABLE_PREVENT_EXTRUDER
+#undef PREVENT_DANGEROUS_EXTRUDE
+#undef PREVENT_LENGTHY_EXTRUDE
+#endif //DEBUG_DISABLE_PREVENT_EXTRUDER
+
 
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
@@ -283,6 +288,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
+#ifdef DEBUG_DISABLE_SWLIMITS
+#define min_software_endstops false
+#define max_software_endstops false
+#endif //DEBUG_DISABLE_SWLIMITS
 
 
 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)

Firmware/Marlin_main.cpp

@@ -1204,6 +1204,7 @@ void setup()
 		eeprom_write_byte((uint8_t*)EEPROM_CALIBRATION_STATUS_PINDA, 0);
 	}
 
+#ifndef DEBUG_SKIP_STARTMSGS
 	check_babystep(); //checking if Z babystep is in allowed range
 	
   if (calibration_status() == CALIBRATION_STATUS_ASSEMBLED ||
@@ -1221,8 +1222,9 @@ void setup()
 	  lcd_update_enable(true);
   } else if (calibration_status() == CALIBRATION_STATUS_Z_CALIBRATION) {
       // Show the message.
-      lcd_show_fullscreen_message_and_wait_P(MSG_FOLLOW_CALIBRATION_FLOW);
+	  lcd_show_fullscreen_message_and_wait_P(MSG_FOLLOW_CALIBRATION_FLOW);
   }
+#endif //DEBUG_SKIP_STARTMSGS
   for (int i = 0; i<4; i++) EEPROM_read_B(EEPROM_BOWDEN_LENGTH + i * 2, &bowden_length[i]);
   lcd_update_enable(true);
 

Firmware/boards.h

@@ -3,8 +3,9 @@
 
 #define BOARD_UNKNOWN -1
 
-#define BOARD_EINY_0_4a         299 // EINY 0.4a
-#define BOARD_EINY_0_3a         300 // EINY 0.3a
+#define BOARD_EINY_0_3a         300  // EINY 0.3a
+#define BOARD_EINY_0_4a         299  // EINY 0.4a
+
 #define BOARD_RAMBO             301  // Rambo
 #define BOARD_RAMBO_MINI_1_3    302  // Rambo-mini 1.3
 #define BOARD_RAMBO_MINI_1_0    102  // Rambo-mini 1.0

Firmware/pins.h

@@ -332,6 +332,8 @@
 #define X_DIR_PIN           49
 #define X_MIN_PIN           12
 #define X_MAX_PIN           30
+//#define X_MIN_PIN           64 //TMC2130 SG homing
+//#define X_MAX_PIN           64 //TMC2130 SG homing
 #define X_ENABLE_PIN        29
 #define X_MS1_PIN -1
 #define X_MS2_PIN -1
@@ -341,6 +343,8 @@
 #define Y_DIR_PIN           48
 #define Y_MIN_PIN           11
 #define Y_MAX_PIN           24
+//#define Y_MIN_PIN           69 //TMC2130 SG homing
+//#define Y_MAX_PIN           69 //TMC2130 SG homing
 #define Y_ENABLE_PIN        28
 #define Y_MS1_PIN -1
 #define Y_MS2_PIN -1
@@ -438,6 +442,8 @@
 #define X_DIR_PIN           49
 #define X_MIN_PIN           12
 #define X_MAX_PIN           30
+//#define X_MIN_PIN           64 //TMC2130 SG homing
+//#define X_MAX_PIN           64 //TMC2130 SG homing
 #define X_ENABLE_PIN        29
 #define X_MS1_PIN -1
 #define X_MS2_PIN -1
@@ -447,6 +453,8 @@
 #define Y_DIR_PIN           48
 #define Y_MIN_PIN           11
 #define Y_MAX_PIN           24
+//#define Y_MIN_PIN           69 //TMC2130 SG homing
+//#define Y_MAX_PIN           69 //TMC2130 SG homing
 #define Y_ENABLE_PIN        28
 #define Y_MS1_PIN -1
 #define Y_MS2_PIN -1

Firmware/temperature.cpp

@@ -1353,6 +1353,9 @@ void max_temp_error(uint8_t e) {
 }
 
 void min_temp_error(uint8_t e) {
+#ifdef DEBUG_DISABLE_MINTEMP
+	return;
+#endif
   disable_heater();
   if(IsStopped() == false) {
     SERIAL_ERROR_START;
@@ -1383,7 +1386,10 @@ void bed_max_temp_error(void) {
 }
 
 void bed_min_temp_error(void) {
-/*#if HEATER_BED_PIN > -1
+#ifdef DEBUG_DISABLE_MINTEMP
+	return;
+#endif
+#if HEATER_BED_PIN > -1
     WRITE(HEATER_BED_PIN, 0);
 #endif
     if(IsStopped() == false) {

Firmware/tmc2130.cpp

@@ -127,7 +127,7 @@ bool tmc2130_update_sg()
 		uint16_t tstep = tmc2130_rd_TSTEP(cs);
 		if (tstep < TMC2130_TCOOLTHRS)
 		{
-			if(sg_homing_delay < 10) // wait for a few tens microsteps until stallGuard is used //todo: read out microsteps directly, instead of delay counter
+			if(sg_homing_delay < TMC2130_SG_DELAY) // wait for a few tens microsteps until stallGuard is used //todo: read out microsteps directly, instead of delay counter
 				sg_homing_delay++;
 			else
 			{

Firmware/ultralcd.cpp

@@ -4986,6 +4986,13 @@ void lcd_update(uint8_t lcdDrawUpdateOverride)
 
   if (lcd_next_update_millis < millis())
   {
+#ifdef DEBUG_BLINK_ACTIVE
+	static bool active_led = false;
+	active_led = !active_led;
+	pinMode(LED_PIN, OUTPUT);
+	digitalWrite(LED_PIN, active_led?HIGH:LOW);
+#endif //DEBUG_BLINK_ACTIVE
+
 #ifdef ULTIPANEL
 #ifdef REPRAPWORLD_KEYPAD
 	  if (REPRAPWORLD_KEYPAD_MOVE_Z_UP) {

Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h

@@ -0,0 +1,461 @@
+#ifndef CONFIGURATION_PRUSA_H
+#define CONFIGURATION_PRUSA_H
+
+/*------------------------------------
+ GENERAL SETTINGS
+ *------------------------------------*/
+
+// Printer revision
+#define FILAMENT_SIZE "1_75mm_MK3"
+#define NOZZLE_TYPE "E3Dv6full"
+
+// Developer flag
+#define DEVELOPER
+
+// Printer name
+#define CUSTOM_MENDEL_NAME "Prusa i3 MK3"
+
+// Electronics
+//#define MOTHERBOARD BOARD_EINY_0_4a
+#define MOTHERBOARD BOARD_EINY_0_3a
+
+
+// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
+//#define E3D_PT100_EXTRUDER_WITH_AMP
+//#define E3D_PT100_EXTRUDER_NO_AMP
+//#define E3D_PT100_BED_WITH_AMP
+//#define E3D_PT100_BED_NO_AMP
+
+
+/*------------------------------------
+ AXIS SETTINGS
+ *------------------------------------*/
+
+// Steps per unit {X,Y,Z,E}
+//#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,140}
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,280}
+
+// Endstop inverting
+const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+
+// Home position
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS -2.2
+#define MANUAL_Z_HOME_POS 0.2
+
+// Travel limits after homing
+#define X_MAX_POS 255
+#define X_MIN_POS 0
+#define Y_MAX_POS 210
+#define Y_MIN_POS -4
+#define Z_MAX_POS 210
+#define Z_MIN_POS 0.15
+
+// Canceled home position
+#define X_CANCEL_POS 50
+#define Y_CANCEL_POS 190
+
+//Pause print position
+#define X_PAUSE_POS 50
+#define Y_PAUSE_POS 190
+#define Z_PAUSE_LIFT 20
+
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+#define HOMING_FEEDRATE {3000, 3000, 800, 0}  // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000
+
+//#define DEFAULT_MAX_FEEDRATE          {400, 400, 12, 120}    // (mm/sec)
+#define DEFAULT_MAX_FEEDRATE          {400, 400, 12, 120}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {1000, 1000, 100, 5000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          1250   // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1250   // X, Y, Z and E max acceleration in mm/s^2 for retracts
+
+
+#define MANUAL_FEEDRATE {2700, 2700, 1000, 100}   // set the speeds for manual moves (mm/min)
+#define MAX_SILENT_FEEDRATE           2700   // 
+
+#define Z_AXIS_ALWAYS_ON 1
+
+//DEBUG
+//#define DEBUG_DISABLE_MINTEMP
+//#define DEBUG_DISABLE_SWLIMITS
+//#define DEBUG_DISABLE_PREVENT_EXTRUDER
+#define DEBUG_BLINK_ACTIVE
+//#define DEBUG_SKIP_STARTMSGS
+
+
+/*------------------------------------
+ TMC2130 default settings
+ *------------------------------------*/
+
+#define TMC2130_FCLK 12000000       // fclk = 12MHz
+
+#define TMC2130_USTEPS_XY 16        // microstep resolution for XY axes
+#define TMC2130_USTEPS_Z  16        // microstep resolution for Z axis
+#define TMC2130_USTEPS_E  16        // microstep resolution for E axis
+#define TMC2130_EXP256_XY 1         // extrapolate 256 for XY axes
+#define TMC2130_EXP256_Z  1         // extrapolate 256 for Z axis
+#define TMC2130_EXP256_E  1         // extrapolate 256 for E axis
+
+// PWM register configuration
+//#define TMC2130_PWM_GRAD 0x08       // 0x0F - Sets gradient - (max 15 with PWM autoscale activated)
+//#define TMC2130_PWM_AMPL 0xC8       // 0xFF - Sets PWM amplitude to 200 (max is 255)
+#define TMC2130_PWM_GRAD 0x01       // 0x0F - Sets gradient - (max 15 with PWM autoscale activated)
+#define TMC2130_PWM_AMPL 0xc8       // 0xFF - Sets PWM amplitude to 200 (max is 255)
+#define TMC2130_PWM_AUTO 0x04       // 0x04 since writing in PWM_CONF (Activates PWM autoscaling)
+//#define TMC2130_PWM_FREQ 0x01       // 0x01 since writing in PWM_CONF (Sets PWM frequency to 2/683 fCLK) 35.1kHz
+#define TMC2130_PWM_FREQ 0x01       // 0x02 since writing in PWM_CONF (Sets PWM frequency to 2/683 fCLK) 46.9kHz
+
+#define TMC2130_PWM_DIV  683        // PWM frequency divider (1024, 683, 512, 410)
+#define TMC2130_PWM_CLK  (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk)
+
+// Special configuration for XY axes for operation (during standstill, use same settings as for other axes) //todo
+// RP: this settings does not work (overtemp)
+//#define TMC2130_PWM_GRAD_XY 156     // 0x0F - Sets gradient - (max 15 with PWM autoscale activated)
+//#define TMC2130_PWM_AMPL_XY 63      // 0xFF - Sets PWM amplitude to 200 (max is 255)
+//#define TMC2130_PWM_AUTO_XY 0x00    // 0x04 since writing in PWM_CONF (Activates PWM autoscaling)
+//#define TMC2130_PWM_FREQ_XY 0x01    // 0x01 since writing in PWM_CONF (Sets PWM frequency to 2/683 fCLK)
+
+#define TMC2130_TPWMTHRS 0          // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode
+#define TMC2130_THIGH 0             // THIGH - unused
+
+#define TMC2130_TCOOLTHRS 239       // TCOOLTHRS - coolstep treshold
+
+#define TMC2130_SG_HOMING     1     // stallguard homing
+#define TMC2130_SG_HOMING_SW  1     // stallguard "software" homing
+#define TMC2130_SG_THRS_X    12     // stallguard sensitivity for X axis
+#define TMC2130_SG_THRS_Y    12     // stallguard sensitivity for Y axis
+#define TMC2130_SG_DELAY     10     // stallguard delay (temporary solution)
+
+#define TMC2130_CURRENTS_H {2, 2, 2, 4}  // default holding currents for all axes
+#define TMC2130_CURRENTS_R {6, 6, 8, 8}  // default running currents for all axes
+#define TMC2130_DEBUG
+#define TMC2130_DEBUG_WR
+#define TMC2130_DEBUG_RD
+
+
+/*------------------------------------
+ EXTRUDER SETTINGS
+ *------------------------------------*/
+
+// Mintemps
+#define HEATER_0_MINTEMP 15
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define BED_MINTEMP 15
+
+// Maxtemps
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define HEATER_0_MAXTEMP 410
+#else
+#define HEATER_0_MAXTEMP 305
+#endif
+#define HEATER_1_MAXTEMP 305
+#define HEATER_2_MAXTEMP 305
+#define BED_MAXTEMP 150
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_Kp 21.70
+#define  DEFAULT_Ki 1.60
+#define  DEFAULT_Kd 73.76
+#else
+// Define PID constants for extruder
+//#define  DEFAULT_Kp 40.925
+//#define  DEFAULT_Ki 4.875
+//#define  DEFAULT_Kd 86.085
+#define  DEFAULT_Kp 16.13
+#define  DEFAULT_Ki 1.1625
+#define  DEFAULT_Kd 56.23
+#endif
+
+// Extrude mintemp
+#define EXTRUDE_MINTEMP 130
+
+// Extruder cooling fans
+#define EXTRUDER_0_AUTO_FAN_PIN   8
+#define EXTRUDER_1_AUTO_FAN_PIN   -1
+#define EXTRUDER_2_AUTO_FAN_PIN   -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
+
+
+
+/*------------------------------------
+ LOAD/UNLOAD FILAMENT SETTINGS
+ *------------------------------------*/
+
+// Load filament commands
+#define LOAD_FILAMENT_0 "M83"
+#define LOAD_FILAMENT_1 "G1 E70 F400"
+#define LOAD_FILAMENT_2 "G1 E40 F100"
+
+// Unload filament commands
+#define UNLOAD_FILAMENT_0 "M83"
+#define UNLOAD_FILAMENT_1 "G1 E-80 F7000"
+
+/*------------------------------------
+ CHANGE FILAMENT SETTINGS
+ *------------------------------------*/
+
+// Filament change configuration
+#define FILAMENTCHANGEENABLE
+#ifdef FILAMENTCHANGEENABLE
+#define FILAMENTCHANGE_XPOS 211
+#define FILAMENTCHANGE_YPOS 0
+#define FILAMENTCHANGE_ZADD 2
+#define FILAMENTCHANGE_FIRSTRETRACT -2
+#define FILAMENTCHANGE_FINALRETRACT -80
+
+#define FILAMENTCHANGE_FIRSTFEED 70
+#define FILAMENTCHANGE_FINALFEED 50
+#define FILAMENTCHANGE_RECFEED 5
+
+#define FILAMENTCHANGE_XYFEED 50
+#define FILAMENTCHANGE_EFEED 20
+#define FILAMENTCHANGE_RFEED 400
+#define FILAMENTCHANGE_EXFEED 2
+#define FILAMENTCHANGE_ZFEED 15
+
+#endif
+
+/*------------------------------------
+ ADDITIONAL FEATURES SETTINGS
+ *------------------------------------*/
+
+// Define Prusa filament runout sensor
+//#define FILAMENT_RUNOUT_SUPPORT
+
+#ifdef FILAMENT_RUNOUT_SUPPORT
+#define FILAMENT_RUNOUT_SENSOR 1
+#endif
+
+// temperature runaway
+//#define TEMP_RUNAWAY_BED_HYSTERESIS 5
+//#define TEMP_RUNAWAY_BED_TIMEOUT 360
+
+#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
+#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
+
+/*------------------------------------
+ MOTOR CURRENT SETTINGS
+ *------------------------------------*/
+
+// Motor Current setting for BIG RAMBo
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135}
+
+// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range
+#if MOTHERBOARD == 102 || MOTHERBOARD == 302 || MOTHERBOARD == 300 || MOTHERBOARD == 299
+#define MOTOR_CURRENT_PWM_RANGE 2000
+#define DEFAULT_PWM_MOTOR_CURRENT  {400, 750, 750} // {XY,Z,E}
+#define DEFAULT_PWM_MOTOR_CURRENT_LOUD  {400, 750, 750} // {XY,Z,E}
+#endif
+
+/*------------------------------------
+ BED SETTINGS
+ *------------------------------------*/
+
+// Define Mesh Bed Leveling system to enable it
+#define MESH_BED_LEVELING
+#ifdef MESH_BED_LEVELING
+
+#define MBL_Z_STEP 0.01
+
+// Mesh definitions
+#define MESH_MIN_X 35
+#define MESH_MAX_X 238
+#define MESH_MIN_Y 6
+#define MESH_MAX_Y 202
+
+// Mesh upsample definition
+#define MESH_NUM_X_POINTS 7
+#define MESH_NUM_Y_POINTS 7
+// Mesh measure definition
+#define MESH_MEAS_NUM_X_POINTS 3
+#define MESH_MEAS_NUM_Y_POINTS 3
+
+#define MESH_HOME_Z_CALIB 0.2
+#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+
+#define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 9     // Z probe to nozzle Y offset: -front +behind
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4  // Z probe to nozzle Z offset: -below (always!)
+#endif
+
+// Bed Temperature Control
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+// Bed temperature compensation settings
+#define BED_OFFSET 10
+#define BED_OFFSET_START 40
+#define BED_OFFSET_CENTER 50
+
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_bedKp 21.70
+#define  DEFAULT_bedKi 1.60
+#define  DEFAULT_bedKd 73.76
+#else
+#define  DEFAULT_bedKp 126.13
+#define  DEFAULT_bedKi 4.30
+#define  DEFAULT_bedKd 924.76
+#endif
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+//    #define  DEFAULT_bedKp 97.1
+//    #define  DEFAULT_bedKi 1.41
+//    #define  DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+/*-----------------------------------
+ PREHEAT SETTINGS
+ *------------------------------------*/
+
+#define PLA_PREHEAT_HOTEND_TEMP 215
+#define PLA_PREHEAT_HPB_TEMP 55
+#define PLA_PREHEAT_FAN_SPEED 0
+
+#define ABS_PREHEAT_HOTEND_TEMP 255
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 0
+
+#define HIPS_PREHEAT_HOTEND_TEMP 220
+#define HIPS_PREHEAT_HPB_TEMP 100
+#define HIPS_PREHEAT_FAN_SPEED 0
+
+#define PP_PREHEAT_HOTEND_TEMP 254
+#define PP_PREHEAT_HPB_TEMP 100
+#define PP_PREHEAT_FAN_SPEED 0
+
+#define PET_PREHEAT_HOTEND_TEMP 240
+#define PET_PREHEAT_HPB_TEMP 90
+#define PET_PREHEAT_FAN_SPEED 0
+
+#define FLEX_PREHEAT_HOTEND_TEMP 230
+#define FLEX_PREHEAT_HPB_TEMP 50
+#define FLEX_PREHEAT_FAN_SPEED 0
+
+/*------------------------------------
+ THERMISTORS SETTINGS
+ *------------------------------------*/
+
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a
+// 247 is Pt100 with 4k7 pullup and PT100 Amplifier
+// 110 is Pt100 with 1k pullup (non standard)
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP)
+#define TEMP_SENSOR_0 247
+#elif defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define TEMP_SENSOR_0 148
+#else
+#define TEMP_SENSOR_0 5
+#endif
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#if defined(E3D_PT100_BED_WITH_AMP)
+#define TEMP_SENSOR_BED 247
+#elif defined(E3D_PT100_BED_NO_AMP)
+#define TEMP_SENSOR_BED 148
+#else
+#define TEMP_SENSOR_BED 1
+#endif
+
+#define STACK_GUARD_TEST_VALUE 0xA2A2
+
+#define MAX_BED_TEMP_CALIBRATION 50
+#define MAX_HOTEND_TEMP_CALIBRATION 50
+
+#define MAX_E_STEPS_PER_UNIT 250
+#define MIN_E_STEPS_PER_UNIT 100
+
+#define Z_BABYSTEP_MIN -3999
+#define Z_BABYSTEP_MAX 0
+
+#define PINDA_PREHEAT_X 70
+#define PINDA_PREHEAT_Y -3
+#define PINDA_PREHEAT_Z 1
+#define PINDA_HEAT_T 120 //time in s
+
+#define PINDA_MIN_T 50
+#define PINDA_STEP_T 10
+#define PINDA_MAX_T 100
+
+#define PING_TIME 60 //time in s
+#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes
+#define PING_ALLERT_PERIOD 60 //time in s
+
+#define LONG_PRESS_TIME 1000 //time in ms for button long press
+#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
+
+#define DEFAULT_PID_TEMP 210
+
+#define MIN_PRINT_FAN_SPEED 50
+
+#ifdef SNMM
+#define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print
+#else
+#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print
+#endif
+
+#endif //__CONFIGURATION_PRUSA_H

Firmware/variants/1_75mm_MK3-EINY04-E3Dv6full.h

@@ -0,0 +1,461 @@
+#ifndef CONFIGURATION_PRUSA_H
+#define CONFIGURATION_PRUSA_H
+
+/*------------------------------------
+ GENERAL SETTINGS
+ *------------------------------------*/
+
+// Printer revision
+#define FILAMENT_SIZE "1_75mm_MK3"
+#define NOZZLE_TYPE "E3Dv6full"
+
+// Developer flag
+#define DEVELOPER
+
+// Printer name
+#define CUSTOM_MENDEL_NAME "Prusa i3 MK3"
+
+// Electronics
+#define MOTHERBOARD BOARD_EINY_0_4a
+//#define MOTHERBOARD BOARD_EINY_0_3a
+
+
+// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
+//#define E3D_PT100_EXTRUDER_WITH_AMP
+//#define E3D_PT100_EXTRUDER_NO_AMP
+//#define E3D_PT100_BED_WITH_AMP
+//#define E3D_PT100_BED_NO_AMP
+
+
+/*------------------------------------
+ AXIS SETTINGS
+ *------------------------------------*/
+
+// Steps per unit {X,Y,Z,E}
+//#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,140}
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,280}
+
+// Endstop inverting
+const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+
+// Home position
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS -2.2
+#define MANUAL_Z_HOME_POS 0.2
+
+// Travel limits after homing
+#define X_MAX_POS 255
+#define X_MIN_POS 0
+#define Y_MAX_POS 210
+#define Y_MIN_POS -4
+#define Z_MAX_POS 210
+#define Z_MIN_POS 0.15
+
+// Canceled home position
+#define X_CANCEL_POS 50
+#define Y_CANCEL_POS 190
+
+//Pause print position
+#define X_PAUSE_POS 50
+#define Y_PAUSE_POS 190
+#define Z_PAUSE_LIFT 20
+
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+#define HOMING_FEEDRATE {3000, 3000, 800, 0}  // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000
+
+//#define DEFAULT_MAX_FEEDRATE          {400, 400, 12, 120}    // (mm/sec)
+#define DEFAULT_MAX_FEEDRATE          {400, 400, 12, 120}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {1000, 1000, 100, 5000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          1250   // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1250   // X, Y, Z and E max acceleration in mm/s^2 for retracts
+
+
+#define MANUAL_FEEDRATE {2700, 2700, 1000, 100}   // set the speeds for manual moves (mm/min)
+#define MAX_SILENT_FEEDRATE           2700   // 
+
+#define Z_AXIS_ALWAYS_ON 1
+
+//DEBUG
+//#define DEBUG_DISABLE_MINTEMP
+//#define DEBUG_DISABLE_SWLIMITS
+//#define DEBUG_DISABLE_PREVENT_EXTRUDER
+#define DEBUG_BLINK_ACTIVE
+//#define DEBUG_SKIP_STARTMSGS
+
+
+/*------------------------------------
+ TMC2130 default settings
+ *------------------------------------*/
+
+#define TMC2130_FCLK 12000000       // fclk = 12MHz
+
+#define TMC2130_USTEPS_XY 16        // microstep resolution for XY axes
+#define TMC2130_USTEPS_Z  16        // microstep resolution for Z axis
+#define TMC2130_USTEPS_E  16        // microstep resolution for E axis
+#define TMC2130_EXP256_XY 1         // extrapolate 256 for XY axes
+#define TMC2130_EXP256_Z  1         // extrapolate 256 for Z axis
+#define TMC2130_EXP256_E  1         // extrapolate 256 for E axis
+
+// PWM register configuration
+//#define TMC2130_PWM_GRAD 0x08       // 0x0F - Sets gradient - (max 15 with PWM autoscale activated)
+//#define TMC2130_PWM_AMPL 0xC8       // 0xFF - Sets PWM amplitude to 200 (max is 255)
+#define TMC2130_PWM_GRAD 0x01       // 0x0F - Sets gradient - (max 15 with PWM autoscale activated)
+#define TMC2130_PWM_AMPL 0xc8       // 0xFF - Sets PWM amplitude to 200 (max is 255)
+#define TMC2130_PWM_AUTO 0x04       // 0x04 since writing in PWM_CONF (Activates PWM autoscaling)
+//#define TMC2130_PWM_FREQ 0x01       // 0x01 since writing in PWM_CONF (Sets PWM frequency to 2/683 fCLK) 35.1kHz
+#define TMC2130_PWM_FREQ 0x01       // 0x02 since writing in PWM_CONF (Sets PWM frequency to 2/683 fCLK) 46.9kHz
+
+#define TMC2130_PWM_DIV  683        // PWM frequency divider (1024, 683, 512, 410)
+#define TMC2130_PWM_CLK  (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk)
+
+// Special configuration for XY axes for operation (during standstill, use same settings as for other axes) //todo
+// RP: this settings does not work (overtemp)
+//#define TMC2130_PWM_GRAD_XY 156     // 0x0F - Sets gradient - (max 15 with PWM autoscale activated)
+//#define TMC2130_PWM_AMPL_XY 63      // 0xFF - Sets PWM amplitude to 200 (max is 255)
+//#define TMC2130_PWM_AUTO_XY 0x00    // 0x04 since writing in PWM_CONF (Activates PWM autoscaling)
+//#define TMC2130_PWM_FREQ_XY 0x01    // 0x01 since writing in PWM_CONF (Sets PWM frequency to 2/683 fCLK)
+
+#define TMC2130_TPWMTHRS 0          // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode
+#define TMC2130_THIGH 0             // THIGH - unused
+
+#define TMC2130_TCOOLTHRS 239       // TCOOLTHRS - coolstep treshold
+
+#define TMC2130_SG_HOMING     1     // stallguard homing
+#define TMC2130_SG_HOMING_SW  1     // stallguard "software" homing
+#define TMC2130_SG_THRS_X    12     // stallguard sensitivity for X axis
+#define TMC2130_SG_THRS_Y    12     // stallguard sensitivity for Y axis
+#define TMC2130_SG_DELAY     10     // stallguard delay (temporary solution)
+
+#define TMC2130_CURRENTS_H {2, 2, 2, 4}  // default holding currents for all axes
+#define TMC2130_CURRENTS_R {6, 6, 8, 8}  // default running currents for all axes
+#define TMC2130_DEBUG
+#define TMC2130_DEBUG_WR
+#define TMC2130_DEBUG_RD
+
+
+/*------------------------------------
+ EXTRUDER SETTINGS
+ *------------------------------------*/
+
+// Mintemps
+#define HEATER_0_MINTEMP 15
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define BED_MINTEMP 15
+
+// Maxtemps
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define HEATER_0_MAXTEMP 410
+#else
+#define HEATER_0_MAXTEMP 305
+#endif
+#define HEATER_1_MAXTEMP 305
+#define HEATER_2_MAXTEMP 305
+#define BED_MAXTEMP 150
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_Kp 21.70
+#define  DEFAULT_Ki 1.60
+#define  DEFAULT_Kd 73.76
+#else
+// Define PID constants for extruder
+//#define  DEFAULT_Kp 40.925
+//#define  DEFAULT_Ki 4.875
+//#define  DEFAULT_Kd 86.085
+#define  DEFAULT_Kp 16.13
+#define  DEFAULT_Ki 1.1625
+#define  DEFAULT_Kd 56.23
+#endif
+
+// Extrude mintemp
+#define EXTRUDE_MINTEMP 130
+
+// Extruder cooling fans
+#define EXTRUDER_0_AUTO_FAN_PIN   8
+#define EXTRUDER_1_AUTO_FAN_PIN   -1
+#define EXTRUDER_2_AUTO_FAN_PIN   -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
+
+
+
+/*------------------------------------
+ LOAD/UNLOAD FILAMENT SETTINGS
+ *------------------------------------*/
+
+// Load filament commands
+#define LOAD_FILAMENT_0 "M83"
+#define LOAD_FILAMENT_1 "G1 E70 F400"
+#define LOAD_FILAMENT_2 "G1 E40 F100"
+
+// Unload filament commands
+#define UNLOAD_FILAMENT_0 "M83"
+#define UNLOAD_FILAMENT_1 "G1 E-80 F7000"
+
+/*------------------------------------
+ CHANGE FILAMENT SETTINGS
+ *------------------------------------*/
+
+// Filament change configuration
+#define FILAMENTCHANGEENABLE
+#ifdef FILAMENTCHANGEENABLE
+#define FILAMENTCHANGE_XPOS 211
+#define FILAMENTCHANGE_YPOS 0
+#define FILAMENTCHANGE_ZADD 2
+#define FILAMENTCHANGE_FIRSTRETRACT -2
+#define FILAMENTCHANGE_FINALRETRACT -80
+
+#define FILAMENTCHANGE_FIRSTFEED 70
+#define FILAMENTCHANGE_FINALFEED 50
+#define FILAMENTCHANGE_RECFEED 5
+
+#define FILAMENTCHANGE_XYFEED 50
+#define FILAMENTCHANGE_EFEED 20
+#define FILAMENTCHANGE_RFEED 400
+#define FILAMENTCHANGE_EXFEED 2
+#define FILAMENTCHANGE_ZFEED 15
+
+#endif
+
+/*------------------------------------
+ ADDITIONAL FEATURES SETTINGS
+ *------------------------------------*/
+
+// Define Prusa filament runout sensor
+//#define FILAMENT_RUNOUT_SUPPORT
+
+#ifdef FILAMENT_RUNOUT_SUPPORT
+#define FILAMENT_RUNOUT_SENSOR 1
+#endif
+
+// temperature runaway
+//#define TEMP_RUNAWAY_BED_HYSTERESIS 5
+//#define TEMP_RUNAWAY_BED_TIMEOUT 360
+
+#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
+#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
+
+/*------------------------------------
+ MOTOR CURRENT SETTINGS
+ *------------------------------------*/
+
+// Motor Current setting for BIG RAMBo
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135}
+
+// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range
+#if MOTHERBOARD == 102 || MOTHERBOARD == 302 || MOTHERBOARD == 300 || MOTHERBOARD == 299
+#define MOTOR_CURRENT_PWM_RANGE 2000
+#define DEFAULT_PWM_MOTOR_CURRENT  {400, 750, 750} // {XY,Z,E}
+#define DEFAULT_PWM_MOTOR_CURRENT_LOUD  {400, 750, 750} // {XY,Z,E}
+#endif
+
+/*------------------------------------
+ BED SETTINGS
+ *------------------------------------*/
+
+// Define Mesh Bed Leveling system to enable it
+#define MESH_BED_LEVELING
+#ifdef MESH_BED_LEVELING
+
+#define MBL_Z_STEP 0.01
+
+// Mesh definitions
+#define MESH_MIN_X 35
+#define MESH_MAX_X 238
+#define MESH_MIN_Y 6
+#define MESH_MAX_Y 202
+
+// Mesh upsample definition
+#define MESH_NUM_X_POINTS 7
+#define MESH_NUM_Y_POINTS 7
+// Mesh measure definition
+#define MESH_MEAS_NUM_X_POINTS 3
+#define MESH_MEAS_NUM_Y_POINTS 3
+
+#define MESH_HOME_Z_CALIB 0.2
+#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+
+#define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 9     // Z probe to nozzle Y offset: -front +behind
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4  // Z probe to nozzle Z offset: -below (always!)
+#endif
+
+// Bed Temperature Control
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+// Bed temperature compensation settings
+#define BED_OFFSET 10
+#define BED_OFFSET_START 40
+#define BED_OFFSET_CENTER 50
+
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_bedKp 21.70
+#define  DEFAULT_bedKi 1.60
+#define  DEFAULT_bedKd 73.76
+#else
+#define  DEFAULT_bedKp 126.13
+#define  DEFAULT_bedKi 4.30
+#define  DEFAULT_bedKd 924.76
+#endif
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+//    #define  DEFAULT_bedKp 97.1
+//    #define  DEFAULT_bedKi 1.41
+//    #define  DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+/*-----------------------------------
+ PREHEAT SETTINGS
+ *------------------------------------*/
+
+#define PLA_PREHEAT_HOTEND_TEMP 215
+#define PLA_PREHEAT_HPB_TEMP 55
+#define PLA_PREHEAT_FAN_SPEED 0
+
+#define ABS_PREHEAT_HOTEND_TEMP 255
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 0
+
+#define HIPS_PREHEAT_HOTEND_TEMP 220
+#define HIPS_PREHEAT_HPB_TEMP 100
+#define HIPS_PREHEAT_FAN_SPEED 0
+
+#define PP_PREHEAT_HOTEND_TEMP 254
+#define PP_PREHEAT_HPB_TEMP 100
+#define PP_PREHEAT_FAN_SPEED 0
+
+#define PET_PREHEAT_HOTEND_TEMP 240
+#define PET_PREHEAT_HPB_TEMP 90
+#define PET_PREHEAT_FAN_SPEED 0
+
+#define FLEX_PREHEAT_HOTEND_TEMP 230
+#define FLEX_PREHEAT_HPB_TEMP 50
+#define FLEX_PREHEAT_FAN_SPEED 0
+
+/*------------------------------------
+ THERMISTORS SETTINGS
+ *------------------------------------*/
+
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a
+// 247 is Pt100 with 4k7 pullup and PT100 Amplifier
+// 110 is Pt100 with 1k pullup (non standard)
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP)
+#define TEMP_SENSOR_0 247
+#elif defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define TEMP_SENSOR_0 148
+#else
+#define TEMP_SENSOR_0 5
+#endif
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#if defined(E3D_PT100_BED_WITH_AMP)
+#define TEMP_SENSOR_BED 247
+#elif defined(E3D_PT100_BED_NO_AMP)
+#define TEMP_SENSOR_BED 148
+#else
+#define TEMP_SENSOR_BED 1
+#endif
+
+#define STACK_GUARD_TEST_VALUE 0xA2A2
+
+#define MAX_BED_TEMP_CALIBRATION 50
+#define MAX_HOTEND_TEMP_CALIBRATION 50
+
+#define MAX_E_STEPS_PER_UNIT 250
+#define MIN_E_STEPS_PER_UNIT 100
+
+#define Z_BABYSTEP_MIN -3999
+#define Z_BABYSTEP_MAX 0
+
+#define PINDA_PREHEAT_X 70
+#define PINDA_PREHEAT_Y -3
+#define PINDA_PREHEAT_Z 1
+#define PINDA_HEAT_T 120 //time in s
+
+#define PINDA_MIN_T 50
+#define PINDA_STEP_T 10
+#define PINDA_MAX_T 100
+
+#define PING_TIME 60 //time in s
+#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes
+#define PING_ALLERT_PERIOD 60 //time in s
+
+#define LONG_PRESS_TIME 1000 //time in ms for button long press
+#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
+
+#define DEFAULT_PID_TEMP 210
+
+#define MIN_PRINT_FAN_SPEED 50
+
+#ifdef SNMM
+#define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print
+#else
+#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print
+#endif
+
+#endif //__CONFIGURATION_PRUSA_H