Isolate the entire farm and statistics code

Firmware/Marlin.h

@@ -312,12 +312,7 @@ extern bool homing_flag;
 extern bool loading_flag;
 extern unsigned long total_filament_used;
 void save_statistics(unsigned long _total_filament_used, unsigned long _total_print_time);
-extern uint8_t status_number;
 extern uint8_t heating_status_counter;
-extern unsigned long PingTime;
-extern bool no_response;
-extern uint8_t important_status;
-extern uint8_t saved_filament_type;
 
 extern bool fan_state[2];
 extern int fan_edge_counter[2];
@@ -474,8 +469,6 @@ void gcode_M701();
 
 #define UVLO !(PINE & (1<<4))
 
-void proc_commands();
-
 
 void M600_load_filament();
 void M600_load_filament_movements();

Firmware/Marlin_main.cpp

@@ -162,8 +162,6 @@
 CardReader card;
 #endif
 
-unsigned long PingTime = _millis();
-
 uint8_t mbl_z_probe_nr = 3; //numer of Z measurements for each point in mesh bed leveling calibration
 
 //used for PINDA temp calibration and pause print
@@ -211,8 +209,6 @@ bool mesh_bed_leveling_flag = false;
 bool prusa_sd_card_upload = false;
 #endif
 
-uint8_t status_number = 0;
-
 unsigned long total_filament_used;
 HeatingStatus heating_status;
 uint8_t heating_status_counter;
@@ -298,10 +294,6 @@ const char errormagic[] PROGMEM = "Error:";
 const char echomagic[] PROGMEM = "echo:";
 const char G28W0[] PROGMEM = "G28 W0";
 
-bool no_response = false;
-uint8_t important_status;
-uint8_t saved_filament_type;
-
 // Define some coordinates outside the clamp limits (making them invalid past the parsing stage) so
 // that they can be used later for various logical checks
 #define X_COORD_INVALID (X_MIN_POS-1)
@@ -1101,25 +1093,7 @@ void setup()
 	setup_killpin();
 	setup_powerhold();
 
-	farm_mode = eeprom_read_byte((uint8_t*)EEPROM_FARM_MODE); 
-	if (farm_mode == 0xFF) {
-		farm_mode = false; //if farm_mode has not been stored to eeprom yet and farm number is set to zero or EEPROM is fresh, deactivate farm mode
-		eeprom_update_byte((uint8_t*)EEPROM_FARM_MODE, farm_mode);
-	} else if (farm_mode) {
-		no_response = true; //we need confirmation by recieving PRUSA thx
-		important_status = 8;
-		prusa_statistics(8);
-#ifdef HAS_SECOND_SERIAL_PORT
-		selectedSerialPort = 1;
-#endif //HAS_SECOND_SERIAL_PORT
-		MYSERIAL.begin(BAUDRATE);
-#ifdef FILAMENT_SENSOR
-		//disabled filament autoload (PFW360)
-		fsensor_autoload_set(false);
-#endif //FILAMENT_SENSOR
-		// ~ FanCheck -> on
-		eeprom_update_byte((uint8_t*)EEPROM_FAN_CHECK_ENABLED, true);
-	}
+    farm_mode_init();
 
 #ifdef TMC2130
     if( FarmOrUserECool() ){
@@ -1403,11 +1377,9 @@ void setup()
     enable_z();
 #endif
 
-    if (farm_mode) {
-        // The farm monitoring SW may accidentally expect 
-        // 2 messages of "printer started" to consider a printer working.
-        prusa_statistics(8);
-    }
+    // The farm monitoring SW may accidentally expect 
+    // 2 messages of "printer started" to consider a printer working.
+    prusa_statistics(8);
 
 	// Enable Toshiba FlashAir SD card / WiFi enahanced card.
 	card.ToshibaFlashAir_enable(eeprom_read_byte((unsigned char*)EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY) == 1);
@@ -2970,7 +2942,7 @@ static void gcode_G28(bool home_x_axis, long home_x_value, bool home_y_axis, lon
     }
 #endif
 
-	  if (farm_mode) { prusa_statistics(20); };
+      prusa_statistics(20);
 
       st_synchronize();
 	  homing_flag = false;
@@ -3680,10 +3652,7 @@ static void gcode_M600(bool automatic, float x_position, float y_position, float
     st_synchronize();
     float lastpos[4];
 
-    if (farm_mode)
-    {
-        prusa_statistics(22);
-    }
+    prusa_statistics(22);
 
     //First backup current position and settings
     int feedmultiplyBckp = feedmultiply;
@@ -3807,10 +3776,7 @@ void gcode_M701()
 {
 	printf_P(PSTR("gcode_M701 begin\n"));
 
-	if (farm_mode)
-	{
-		prusa_statistics(22);
-	}
+    prusa_statistics(22);
 
 	if (mmu_enabled) 
 	{
@@ -4419,13 +4385,12 @@ void process_commands()
     
     Set of internal PRUSA commands
     #### Usage
-         PRUSA [ Ping | PRN | FAN | fn | thx | uvlo | MMURES | RESET | fv | M28 | SN | Fir | Rev | Lang | Lz | FR ]
+         PRUSA [ Ping | PRN | FAN | thx | uvlo | MMURES | RESET | fv | M28 | SN | Fir | Rev | Lang | Lz | FR ]
     
     #### Parameters
       - `Ping` 
       - `PRN` - Prints revision of the printer
       - `FAN` - Prints fan details
-      - `fn` - Prints farm no.
       - `thx` 
       - `uvlo` 
       - `MMURES` - Reset MMU
@@ -4443,29 +4408,17 @@ void process_commands()
       - `nozzle` - prints nozzle diameter (farm mode only), works like M862.1 P, e.g. `PRUSA nozzle`
     */
 
-
-		if (code_seen_P(PSTR("Ping"))) {  // PRUSA Ping
-			if (farm_mode) {
-				PingTime = _millis();
-			}	  
-		}
-		else if (code_seen_P(PSTR("PRN"))) { // PRUSA PRN
-		  printf_P(_N("%u"), status_number);
-
-        } else if( code_seen_P(PSTR("FANPINTST"))){
+        if (farm_prusa_code_seen()) {}
+        else if( code_seen_P(PSTR("FANPINTST"))) {
             gcode_PRUSA_BadRAMBoFanTest();
-        }else if (code_seen_P(PSTR("FAN"))) { // PRUSA FAN
-			printf_P(_N("E0:%d RPM\nPRN0:%d RPM\n"), 60*fan_speed[0], 60*fan_speed[1]);
-		}
-		else if (code_seen_P(PSTR("thx"))) // PRUSA thx
-		{
-			no_response = false;
-		}	
-		else if (code_seen_P(PSTR("uvlo"))) // PRUSA uvlo
-		{
-               eeprom_update_byte((uint8_t*)EEPROM_UVLO,0); 
-               enquecommand_P(PSTR("M24")); 
-		}	
+        }
+        else if (code_seen_P(PSTR("FAN"))) { // PRUSA FAN
+            printf_P(_N("E0:%d RPM\nPRN0:%d RPM\n"), 60*fan_speed[0], 60*fan_speed[1]);
+        }
+        else if (code_seen_P(PSTR("uvlo"))) { // PRUSA uvlo
+            eeprom_update_byte((uint8_t*)EEPROM_UVLO,0); 
+            enquecommand_P(PSTR("M24")); 
+        }
 		else if (code_seen_P(PSTR("MMURES"))) // PRUSA MMURES
 		{
 			mmu_reset();
@@ -5546,30 +5499,23 @@ eeprom_update_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM,0xFFFF);
     }
     break;
 
+#ifdef PRUSA_FARM
     /*!
     ### G98 - Activate farm mode <a href="https://reprap.org/wiki/G-code#G98:_Activate_farm_mode">G98: Activate farm mode</a>
-	Enable Prusa-specific Farm functions and g-code.
+    Enable Prusa-specific Farm functions and g-code.
     See Internal Prusa commands.
     */
-	case 98:
-		farm_mode = 1;
-		PingTime = _millis();
-		eeprom_update_byte((unsigned char *)EEPROM_FARM_MODE, farm_mode);
-		SilentModeMenu = SILENT_MODE_OFF;
-		eeprom_update_byte((unsigned char *)EEPROM_SILENT, SilentModeMenu);
-		fCheckModeInit();                       // alternatively invoke printer reset
-		break;
+    case 98:
+        farm_gcode_g98();
+        break;
 
     /*! ### G99 - Deactivate farm mode <a href="https://reprap.org/wiki/G-code#G99:_Deactivate_farm_mode">G99: Deactivate farm mode</a>
- 	Disables Prusa-specific Farm functions and g-code.
-   */
-	case 99:
-		farm_mode = 0;
-		lcd_printer_connected();
-		eeprom_update_byte((unsigned char *)EEPROM_FARM_MODE, farm_mode);
-		lcd_update(2);
-          fCheckModeInit();                       // alternatively invoke printer reset
-		break;
+    Disables Prusa-specific Farm functions and g-code.
+    */
+    case 99:
+        farm_gcode_g99();
+        break;
+#endif //PRUSA_FARM
 	default:
 		printf_P(MSG_UNKNOWN_CODE, 'G', cmdbuffer + bufindr + CMDHDRSIZE);
     }
@@ -6437,7 +6383,7 @@ Sigma_Exit:
       }
       LCD_MESSAGERPGM(_T(MSG_HEATING));
 	  heating_status = HeatingStatus::EXTRUDER_HEATING;
-	  if (farm_mode) { prusa_statistics(1); };
+      prusa_statistics(1);
 
 #ifdef AUTOTEMP
         autotemp_enabled=false;
@@ -6468,7 +6414,7 @@ Sigma_Exit:
 
         LCD_MESSAGERPGM(_T(MSG_HEATING_COMPLETE));
 		heating_status = HeatingStatus::EXTRUDER_HEATING_COMPLETE;
-		if (farm_mode) { prusa_statistics(2); };
+        prusa_statistics(2);
         
         //starttime=_millis();
         previous_millis_cmd.start();
@@ -6494,7 +6440,7 @@ Sigma_Exit:
         bool CooldownNoWait = false;
         LCD_MESSAGERPGM(_T(MSG_BED_HEATING));
 		heating_status = HeatingStatus::BED_HEATING;
-		if (farm_mode) { prusa_statistics(1); };
+        prusa_statistics(1);
         if (code_seen('S')) 
 		{
           setTargetBed(code_value());
@@ -8331,14 +8277,6 @@ Sigma_Exit:
                          nDiameter=(uint16_t)(code_value()*1000.0+0.5); // [,um]
                          nozzle_diameter_check(nDiameter);
                          }
-/*
-                    else if(code_seen('S')&&farm_mode)
-                         {
-                         nDiameter=(uint16_t)(code_value()*1000.0+0.5); // [,um]
-                         eeprom_update_byte((uint8_t*)EEPROM_NOZZLE_DIAMETER,(uint8_t)ClNozzleDiameter::_Diameter_Undef); // for correct synchronization after farm-mode exiting
-                         eeprom_update_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM,nDiameter);
-                         }
-*/
                     else if(code_seen('Q'))
                          SERIAL_PROTOCOLLN((float)eeprom_read_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM)/1000.0);
                     break;

Firmware/Prusa_farm.cpp

@@ -1,3 +1,429 @@
 #include "Prusa_farm.h"
+#include "macros.h"
+#include "Marlin.h"
+#include "cmdqueue.h"
+#include "temperature.h"
+#include "cardreader.h"
+#include "conv2str.h"
+#include "util.h"
+#include "ultralcd.h"
+#include "fsensor.h" //to be converted to Filament_sensor.h...
+
+#ifdef PRUSA_FARM
+
+#define PING_TIME 60 //time in s
+#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
+#define PING_ALLERT_PERIOD 60 //time in s
+
+#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
+#define NC_BUTTON_LONG_PRESS 15 //time in s
 
 uint8_t farm_mode = 0;
+
+static ShortTimer NcTime;
+static uint8_t farm_timer = 8;
+static bool printer_connected = true;
+static unsigned long PingTime = 0;
+static uint8_t status_number = 0;
+static bool no_response = false;
+static uint8_t important_status;
+
+
+static void prusa_statistics_err(char c);
+static void prusa_stat_printerstatus(uint8_t _status);
+static void prusa_stat_farm_number();
+static void prusa_stat_diameter();
+static void prusa_stat_temperatures();
+static void prusa_stat_printinfo();
+static void lcd_send_status();
+#ifdef FARM_CONNECT_MESSAGE
+static void proc_commands();
+static void lcd_connect_printer();
+#endif //FARM_CONNECT_MESSAGE
+static void lcd_ping();
+
+
+static void prusa_statistics_err(char c) {
+    SERIAL_ECHOPGM("{[ERR:");
+    SERIAL_ECHO(c);
+    SERIAL_ECHO(']');
+    prusa_stat_farm_number();
+}
+
+static void prusa_statistics_case0(uint8_t statnr) {
+    SERIAL_ECHO('{');
+    prusa_stat_printerstatus(statnr);
+    prusa_stat_farm_number();
+    prusa_stat_printinfo();
+}
+
+static void prusa_stat_printerstatus(uint8_t _status) {
+    SERIAL_ECHOPGM("[PRN:");
+    SERIAL_ECHO(_status);
+    SERIAL_ECHO(']');
+}
+
+static void prusa_stat_farm_number() {
+    SERIAL_ECHOPGM("[PFN:0]");
+}
+
+static void prusa_stat_diameter() {
+    SERIAL_ECHOPGM("[DIA:");
+    SERIAL_ECHO(eeprom_read_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM));
+    SERIAL_ECHO(']');
+}
+
+static void prusa_stat_temperatures() {
+    SERIAL_ECHOPGM("[ST0:");
+    SERIAL_ECHO(target_temperature[0]);
+    SERIAL_ECHOPGM("][STB:");
+    SERIAL_ECHO(target_temperature_bed);
+    SERIAL_ECHOPGM("][AT0:");
+    SERIAL_ECHO(current_temperature[0]);
+    SERIAL_ECHOPGM("][ATB:");
+    SERIAL_ECHO(current_temperature_bed);
+    SERIAL_ECHO(']');
+}
+
+static void prusa_stat_printinfo() {
+    SERIAL_ECHOPGM("[TFU:");
+    SERIAL_ECHO(total_filament_used);
+    SERIAL_ECHOPGM("][PCD:");
+    SERIAL_ECHO(itostr3(card.percentDone()));
+    SERIAL_ECHOPGM("][FEM:");
+    SERIAL_ECHO(itostr3(feedmultiply));
+    SERIAL_ECHOPGM("][FNM:");
+    SERIAL_ECHO(card.longFilename[0] ? card.longFilename : card.filename);
+    SERIAL_ECHOPGM("][TIM:");
+    if (starttime != 0) {
+        SERIAL_ECHO(_millis() / 1000 - starttime / 1000);
+    }
+    else {
+        SERIAL_ECHO(0);
+    }
+    SERIAL_ECHOPGM("][FWR:");
+    SERIAL_ECHORPGM(FW_VERSION_STR_P());
+    SERIAL_ECHO(']');
+    prusa_stat_diameter();
+}
+
+static void lcd_send_status() {
+    if (farm_mode && no_response && (NcTime.expired(NC_TIME * 1000))) {
+        //send important status messages periodicaly
+        prusa_statistics(important_status);
+        NcTime.start();
+#ifdef FARM_CONNECT_MESSAGE
+        lcd_connect_printer();
+#endif //FARM_CONNECT_MESSAGE
+    }
+}
+
+#ifdef FARM_CONNECT_MESSAGE
+static void proc_commands() {
+    if (buflen) {
+        process_commands();
+        if (!cmdbuffer_front_already_processed)
+            cmdqueue_pop_front();
+        cmdbuffer_front_already_processed = false;
+    }
+}
+
+static void lcd_connect_printer() {
+    lcd_update_enable(false);
+    lcd_clear();
+
+    int i = 0;
+    int t = 0;
+    lcd_puts_at_P(0, 0, PSTR("Connect printer to")); 
+    lcd_puts_at_P(0, 1, PSTR("monitoring or hold"));
+    lcd_puts_at_P(0, 2, PSTR("the knob to continue"));
+    while (no_response) {
+        i++;
+        t++;
+        delay_keep_alive(100);
+        proc_commands();
+        if (t == 10) {
+            prusa_statistics(important_status);
+            t = 0;
+        }
+        if (READ(BTN_ENC)) { //if button is not pressed
+            i = 0; 
+            lcd_puts_at_P(0, 3, PSTR("                    "));
+        }
+        if (i != 0)
+            lcd_putc_at((i * 20) / (NC_BUTTON_LONG_PRESS * 10), 3, LCD_STR_SOLID_BLOCK[0]);
+        if (i == NC_BUTTON_LONG_PRESS * 10)
+            no_response = false;
+    }
+    lcd_update_enable(true);
+    lcd_update(2);
+}
+#endif //FARM_CONNECT_MESSAGE
+
+static void lcd_ping() { //chceck if printer is connected to monitoring when in farm mode
+    if (farm_mode) {
+        bool empty = cmd_buffer_empty();
+        if ((_millis() - PingTime) * 0.001 > (empty ? PING_TIME : PING_TIME_LONG)) {
+            //if commands buffer is empty use shorter time period
+            //if there are comamnds in buffer, some long gcodes can delay execution of ping command
+            //therefore longer period is used
+            printer_connected = false;
+        }
+        else {
+            printer_connected = true;
+        }
+    }
+}
+
+
+
+
+
+void prusa_statistics(uint8_t _message) {
+    const uint8_t _fil_nr = 0;
+    if (!farm_mode)
+        return;
+    
+    switch (_message) {
+    case 0: // default message
+        if (busy_state == PAUSED_FOR_USER) {
+            prusa_statistics_case0(15);
+        }
+        else if (isPrintPaused) {
+            prusa_statistics_case0(14);
+        }
+        else if (IS_SD_PRINTING || loading_flag) {
+            prusa_statistics_case0(4);
+        }
+        else {
+            SERIAL_ECHO('{');
+            prusa_stat_printerstatus(1);
+            prusa_stat_farm_number();
+            prusa_stat_diameter();
+            status_number = 1;
+        }
+        break;
+
+    case 1: // 1 heating
+        SERIAL_ECHO('{');
+        prusa_stat_printerstatus(2);
+        prusa_stat_farm_number();
+        status_number = 2;
+        farm_timer = 1;
+        break;
+
+    case 2: // heating done
+        SERIAL_ECHO('{');
+        prusa_stat_printerstatus(3);
+        prusa_stat_farm_number();
+        SERIAL_ECHOLN('}');
+        status_number = 3;
+        farm_timer = 1;
+
+        if (IS_SD_PRINTING || loading_flag) {
+            SERIAL_ECHO('{');
+            prusa_stat_printerstatus(4);
+            prusa_stat_farm_number();
+            status_number = 4;
+        }
+        else {
+            SERIAL_ECHO('{');
+            prusa_stat_printerstatus(3);
+            prusa_stat_farm_number();
+            status_number = 3;
+        }
+        farm_timer = 1;
+        break;
+
+    case 3: // filament change
+        // must do a return here to prevent doing SERIAL_ECHOLN("}") at the very end of this function
+        // saved a considerable amount of FLASH
+        return;
+        break;
+    case 4: // print succesfull
+        SERIAL_ECHOPGM("{[RES:1][FIL:");
+        MYSERIAL.print(int(_fil_nr));
+        SERIAL_ECHO(']');
+        prusa_stat_printerstatus(status_number);
+        prusa_stat_farm_number();
+        farm_timer = 2;
+        break;
+    case 5: // print not succesfull
+        SERIAL_ECHOPGM("{[RES:0][FIL:");
+        MYSERIAL.print(int(_fil_nr));
+        SERIAL_ECHO(']');
+        prusa_stat_printerstatus(status_number);
+        prusa_stat_farm_number();
+        farm_timer = 2;
+        break;
+    case 6: // print done
+        SERIAL_ECHOPGM("{[PRN:8]");
+        prusa_stat_farm_number();
+        status_number = 8;
+        farm_timer = 2;
+        break;
+    case 7:        // print done - stopped
+        SERIAL_ECHOPGM("{[PRN:9]");
+        prusa_stat_farm_number();
+        status_number = 9;
+        farm_timer = 2;
+        break;
+    case 8: // printer started
+        SERIAL_ECHOPGM("{[PRN:0]");
+        prusa_stat_farm_number();
+        status_number = 0;
+        farm_timer = 2;
+        break;
+    case 20: // echo farm no
+        SERIAL_ECHO('{');
+        prusa_stat_printerstatus(status_number);
+        prusa_stat_farm_number();
+        farm_timer = 4;
+        break;
+    case 21: // temperatures
+        SERIAL_ECHO('{');
+        prusa_stat_temperatures();
+        prusa_stat_farm_number();
+        prusa_stat_printerstatus(status_number);
+        break;
+    case 22: // waiting for filament change
+        SERIAL_ECHOPGM("{[PRN:5]");
+        prusa_stat_farm_number();
+        status_number = 5;
+        break;
+
+    case 90: // Error - Thermal Runaway
+        prusa_statistics_err('1');
+        break;
+    case 91: // Error - Thermal Runaway Preheat
+        prusa_statistics_err('2');
+        break;
+    case 92: // Error - Min temp
+        prusa_statistics_err('3');
+        break;
+    case 93: // Error - Max temp
+        prusa_statistics_err('4');
+        break;
+
+    case 99: // heartbeat
+        SERIAL_ECHOPGM("{[PRN:99]");
+        prusa_stat_temperatures();
+        prusa_stat_farm_number();
+        break;
+    }
+    SERIAL_ECHOLN('}');
+}
+
+void prusa_statistics_update_from_status_screen() {
+    if (farm_mode) {
+        farm_timer--;
+        if (farm_timer < 1) {
+            farm_timer = 10;
+            prusa_statistics(0);
+        }
+        switch (farm_timer) {
+        case 8:
+            prusa_statistics(21);
+            if(loading_flag)
+                prusa_statistics(22);
+            break;
+        case 5:
+            if (IS_SD_PRINTING)
+                prusa_statistics(20);
+            break;
+        }
+    }
+}
+
+void prusa_statistics_update_from_lcd_update() {
+    lcd_ping(); //check that we have received ping command if we are in farm mode
+    lcd_send_status();
+}
+
+void farm_mode_init() {
+    farm_mode = eeprom_read_byte((uint8_t*)EEPROM_FARM_MODE); 
+    if (farm_mode == 0xFF) {
+        farm_mode = false; //if farm_mode has not been stored to eeprom yet and farm number is set to zero or EEPROM is fresh, deactivate farm mode
+        eeprom_update_byte((uint8_t*)EEPROM_FARM_MODE, farm_mode);
+    }
+    else if (farm_mode) {
+        no_response = true; //we need confirmation by recieving PRUSA thx
+        important_status = 8;
+        prusa_statistics(8);
+#ifdef HAS_SECOND_SERIAL_PORT
+        selectedSerialPort = 1;
+#endif //HAS_SECOND_SERIAL_PORT
+        MYSERIAL.begin(BAUDRATE);
+#ifdef FILAMENT_SENSOR
+        //to be converted to Filament_sensor.h...
+        //disabled filament autoload (PFW360)
+        fsensor_autoload_set(false);
+#endif //FILAMENT_SENSOR
+        // ~ FanCheck -> on
+        eeprom_update_byte((uint8_t*)EEPROM_FAN_CHECK_ENABLED, true);
+    }
+}
+
+bool farm_prusa_code_seen() {
+    if (!farm_mode)
+        return false;
+    
+    if (code_seen_P(PSTR("Ping"))) {  // PRUSA Ping
+        PingTime = _millis();
+    }
+    else if (code_seen_P(PSTR("PRN"))) { // PRUSA PRN
+        printf_P(_N("%u"), status_number);
+    }
+    else if (code_seen_P(PSTR("thx"))) { // PRUSA thx
+        no_response = false;
+    }
+    else {
+        return false;
+    }
+    
+    return true;
+}
+
+void farm_gcode_g98() {
+    farm_mode = 1;
+    PingTime = _millis();
+    eeprom_update_byte((unsigned char *)EEPROM_FARM_MODE, farm_mode);
+    SilentModeMenu = SILENT_MODE_OFF;
+    eeprom_update_byte((unsigned char *)EEPROM_SILENT, SilentModeMenu);
+    fCheckModeInit(); // alternatively invoke printer reset
+}
+
+void farm_gcode_g99() {
+    farm_mode = 0;
+    printer_connected = true;
+    eeprom_update_byte((unsigned char *)EEPROM_FARM_MODE, farm_mode);
+    lcd_update(2);
+    fCheckModeInit(); // alternatively invoke printer reset
+}
+
+#else //PRUSA_FARM
+
+void prusa_statistics(_UNUSED uint8_t message) {
+}
+
+void prusa_statistics_update_from_status_screen() {
+}
+
+void prusa_statistics_update_from_lcd_update() {
+}
+
+void farm_mode_init() {
+}
+
+bool farm_prusa_code_seen() {
+    return false;
+}
+
+void farm_gcode_g98() {
+}
+
+void farm_gcode_g99() {
+}
+
+#endif //PRUSA_FARM
+

Firmware/Prusa_farm.h

@@ -7,5 +7,12 @@
 extern uint8_t farm_mode;
 #else
 #define farm_mode 0
-#error prusa_farm_include_error
 #endif
+
+extern void prusa_statistics(uint8_t _message);
+extern void prusa_statistics_update_from_status_screen();
+extern void prusa_statistics_update_from_lcd_update();
+extern void farm_mode_init();
+extern bool farm_prusa_code_seen();
+extern void farm_gcode_g98();
+extern void farm_gcode_g99();

Firmware/cmdqueue.cpp

@@ -368,16 +368,6 @@ void repeatcommand_front()
     cmdbuffer_front_already_processed = true;
 } 
 
-void proc_commands() {
-	if (buflen)
-	{
-		process_commands();
-		if (!cmdbuffer_front_already_processed)
-			cmdqueue_pop_front();
-		cmdbuffer_front_already_processed = false;
-	}
-}
-
 void get_command()
 {
     // Test and reserve space for the new command string.

Firmware/temperature.cpp

@@ -1041,10 +1041,8 @@ static void temp_runaway_stop(bool isPreheat, bool isBed)
                 SERIAL_ERRORLNPGM(" HOTEND THERMAL RUNAWAY");
             }
         }
-        if (farm_mode) {
-            prusa_statistics(0);
-            prusa_statistics(isPreheat? 91 : 90);
-        }
+        prusa_statistics(0);
+        prusa_statistics(isPreheat? 91 : 90);
     }
     ThermalStop();
 }
@@ -1076,7 +1074,7 @@ static void temp_error_messagepgm(const char* PROGMEM type, uint8_t e = EXTRUDER
 static void max_temp_error(uint8_t e) {
     if(IsStopped() == false) {
         temp_error_messagepgm(PSTR("MAXTEMP"), e);
-        if (farm_mode) prusa_statistics(93);
+        prusa_statistics(93);
     }
 #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
     ThermalStop();
@@ -1087,7 +1085,7 @@ static void min_temp_error(uint8_t e) {
     static const char err[] PROGMEM = "MINTEMP";
     if(IsStopped() == false) {
         temp_error_messagepgm(err, e);
-        if (farm_mode) prusa_statistics(92);
+        prusa_statistics(92);
     }
     ThermalStop();
 }

Firmware/ultralcd.cpp

@@ -56,7 +56,6 @@
 #include "Prusa_farm.h"
 
 int clock_interval = 0;
-static ShortTimer NcTime;
 static void lcd_sd_updir();
 static void lcd_mesh_bed_leveling_settings();
 #ifdef LCD_BL_PIN
@@ -82,8 +81,6 @@ CustomMsg custom_message_type = CustomMsg::Status;
 uint8_t custom_message_state = 0;
 
 bool isPrintPaused = false;
-uint8_t farm_timer = 8;
-bool printer_connected = true;
 
 static ShortTimer display_time; //just timer for showing pid finished message on lcd;
 static uint16_t pid_temp = DEFAULT_PID_TEMP;
@@ -125,11 +122,6 @@ static void lcd_control_temperature_menu();
 #ifdef TMC2130
 static void lcd_settings_linearity_correction_menu_save();
 #endif
-static void prusa_stat_printerstatus(uint8_t _status);
-static void prusa_stat_farm_number();
-static void prusa_stat_diameter();
-static void prusa_stat_temperatures();
-static void prusa_stat_printinfo();
 static void lcd_menu_xyz_y_min();
 static void lcd_menu_xyz_skew();
 static void lcd_menu_xyz_offset();
@@ -249,10 +241,6 @@ static void lcd_cutter_enabled();
  static void lcd_sort_type_set();
 #endif
 static void lcd_babystep_z();
-static void lcd_send_status();
-#ifdef FARM_CONNECT_MESSAGE
-static void lcd_connect_printer();
-#endif //FARM_CONNECT_MESSAGE
 
 //! Beware: has side effects - forces lcd_draw_update to 2, which means clear the display
 void lcd_finishstatus();
@@ -820,27 +808,7 @@ void lcd_status_screen()                          // NOT static due to using ins
 
 		lcdui_print_status_screen();
 
-		if (farm_mode)
-		{
-			farm_timer--;
-			if (farm_timer < 1)
-			{
-				farm_timer = 10;
-				prusa_statistics(0);
-			}
-			switch (farm_timer)
-			{
-			case 8:
-				prusa_statistics(21);
-				if(loading_flag)
-					prusa_statistics(22);
-				break;
-			case 5:
-				if (IS_SD_PRINTING)
-					prusa_statistics(20);
-				break;
-			}
-		} // end of farm_mode
+		prusa_statistics_update_from_status_screen();
 
 		if (lcd_commands_type != LcdCommands::Idle)
 			lcd_commands();
@@ -3568,321 +3536,6 @@ void lcd_menu_show_sensors_state()                // NOT static due to using ins
 	menu_back_if_clicked();
 }
 
-void prusa_statistics_err(char c){
-	SERIAL_ECHOPGM("{[ERR:");
-	SERIAL_ECHO(c);
-	SERIAL_ECHO(']');
-	prusa_stat_farm_number();
-}
-
-static void prusa_statistics_case0(uint8_t statnr){
-	SERIAL_ECHO('{');
-	prusa_stat_printerstatus(statnr);
-	prusa_stat_farm_number();
-	prusa_stat_printinfo();
-}
-
-void prusa_statistics(uint8_t _message, uint8_t _fil_nr) {
-#ifdef DEBUG_DISABLE_PRUSA_STATISTICS
-	return;
-#endif //DEBUG_DISABLE_PRUSA_STATISTICS
-	switch (_message)
-	{
-
-	case 0: // default message
-		if (busy_state == PAUSED_FOR_USER) 
-		{   
-			prusa_statistics_case0(15);
-		}
-		else if (isPrintPaused)
-		{
-			prusa_statistics_case0(14);
-		}
-		else if (IS_SD_PRINTING || loading_flag)
-		{
-			prusa_statistics_case0(4);
-		}
-		else
-		{
-			SERIAL_ECHO('{');
-			prusa_stat_printerstatus(1);
-			prusa_stat_farm_number();
-			prusa_stat_diameter();
-			status_number = 1;
-		}
-		break;
-
-	case 1:		// 1 heating
-		SERIAL_ECHO('{');
-		prusa_stat_printerstatus(2);
-		prusa_stat_farm_number();
-		status_number = 2;
-		farm_timer = 1;
-		break;
-
-	case 2:		// heating done
-		SERIAL_ECHO('{');
-		prusa_stat_printerstatus(3);
-		prusa_stat_farm_number();
-		SERIAL_ECHOLN('}');
-		status_number = 3;
-		farm_timer = 1;
-
-		if (IS_SD_PRINTING || loading_flag)
-		{
-			SERIAL_ECHO('{');
-			prusa_stat_printerstatus(4);
-			prusa_stat_farm_number();
-			status_number = 4;
-		}
-		else
-		{
-			SERIAL_ECHO('{');
-			prusa_stat_printerstatus(3);
-			prusa_stat_farm_number();
-			status_number = 3;
-		}
-		farm_timer = 1;
-		break;
-
-	case 3:		// filament change
-		// must do a return here to prevent doing SERIAL_ECHOLN("}") at the very end of this function
-		// saved a considerable amount of FLASH
-		return;
-		break;
-	case 4:		// print succesfull
-		SERIAL_ECHOPGM("{[RES:1][FIL:");
-		MYSERIAL.print(int(_fil_nr));
-		SERIAL_ECHO(']');
-		prusa_stat_printerstatus(status_number);
-		prusa_stat_farm_number();
-		farm_timer = 2;
-		break;
-	case 5:		// print not succesfull
-		SERIAL_ECHOPGM("{[RES:0][FIL:");
-		MYSERIAL.print(int(_fil_nr));
-		SERIAL_ECHO(']');
-		prusa_stat_printerstatus(status_number);
-		prusa_stat_farm_number();
-		farm_timer = 2;
-		break;
-	case 6:		// print done
-		SERIAL_ECHOPGM("{[PRN:8]");
-		prusa_stat_farm_number();
-		status_number = 8;
-		farm_timer = 2;
-		break;
-	case 7:		// print done - stopped
-		SERIAL_ECHOPGM("{[PRN:9]");
-		prusa_stat_farm_number();
-		status_number = 9;
-		farm_timer = 2;
-		break;
-	case 8:		// printer started
-		SERIAL_ECHOPGM("{[PRN:0]");
-		prusa_stat_farm_number();
-		status_number = 0;
-		farm_timer = 2;
-		break;
-	case 20:		// echo farm no
-		SERIAL_ECHO('{');
-		prusa_stat_printerstatus(status_number);
-		prusa_stat_farm_number();
-		farm_timer = 4;
-		break;
-	case 21: // temperatures
-		SERIAL_ECHO('{');
-		prusa_stat_temperatures();
-		prusa_stat_farm_number();
-		prusa_stat_printerstatus(status_number);
-		break;
-    case 22: // waiting for filament change
-        SERIAL_ECHOPGM("{[PRN:5]");
-		prusa_stat_farm_number();
-		status_number = 5;
-        break;
-	
-	case 90: // Error - Thermal Runaway
-		prusa_statistics_err('1');
-		break;
-	case 91: // Error - Thermal Runaway Preheat
-		prusa_statistics_err('2');
-		break;
-	case 92: // Error - Min temp
-		prusa_statistics_err('3');
-		break;
-	case 93: // Error - Max temp
-		prusa_statistics_err('4');
-		break;
-
-    case 99:		// heartbeat
-        SERIAL_ECHOPGM("{[PRN:99]");
-        prusa_stat_temperatures();
-		prusa_stat_farm_number();
-        break;
-	}
-	SERIAL_ECHOLN('}');	
-
-}
-
-static void prusa_stat_printerstatus(uint8_t _status)
-{
-	SERIAL_ECHOPGM("[PRN:");
-	SERIAL_ECHO(_status);
-	SERIAL_ECHO(']');
-}
-
-static void prusa_stat_farm_number() {
-	SERIAL_ECHOPGM("[PFN:0]");
-}
-
-static void prusa_stat_diameter() {
-	SERIAL_ECHOPGM("[DIA:");
-	SERIAL_ECHO(eeprom_read_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM));
-	SERIAL_ECHO(']');
-}
-
-static void prusa_stat_temperatures()
-{
-	SERIAL_ECHOPGM("[ST0:");
-	SERIAL_ECHO(target_temperature[0]);
-	SERIAL_ECHOPGM("][STB:");
-	SERIAL_ECHO(target_temperature_bed);
-	SERIAL_ECHOPGM("][AT0:");
-	SERIAL_ECHO(current_temperature[0]);
-	SERIAL_ECHOPGM("][ATB:");
-	SERIAL_ECHO(current_temperature_bed);
-	SERIAL_ECHO(']');
-}
-
-static void prusa_stat_printinfo()
-{
-	SERIAL_ECHOPGM("[TFU:");
-	SERIAL_ECHO(total_filament_used);
-	SERIAL_ECHOPGM("][PCD:");
-	SERIAL_ECHO(itostr3(card.percentDone()));
-	SERIAL_ECHOPGM("][FEM:");
-	SERIAL_ECHO(itostr3(feedmultiply));
-	SERIAL_ECHOPGM("][FNM:");
-	SERIAL_ECHO(card.longFilename[0] ? card.longFilename : card.filename);
-	SERIAL_ECHOPGM("][TIM:");
-	if (starttime != 0)
-	{
-		SERIAL_ECHO(_millis() / 1000 - starttime / 1000);
-	}
-	else
-	{
-		SERIAL_ECHO(0);
-	}
-	SERIAL_ECHOPGM("][FWR:");
-	SERIAL_ECHORPGM(FW_VERSION_STR_P());
-	SERIAL_ECHO(']');
-     prusa_stat_diameter();
-}
-
-/*
-void lcd_pick_babystep(){
-    int enc_dif = 0;
-    int cursor_pos = 1;
-    int fsm = 0;
-    
-    
-    
-    
-    lcd_clear();
-    
-    lcd_set_cursor(0, 0);
-    
-    lcd_puts_P(_i("Pick print"));////MSG_PICK_Z
-    
-    
-    lcd_set_cursor(3, 2);
-    
-    lcd_print('1');
-    
-    lcd_set_cursor(3, 3);
-    
-    lcd_print('2');
-    
-    lcd_set_cursor(12, 2);
-    
-    lcd_print('3');
-    
-    lcd_set_cursor(12, 3);
-    
-    lcd_print('4');
-    
-    lcd_set_cursor(1, 2);
-    
-    lcd_print('>');
-    
-    
-    enc_dif = lcd_encoder_diff;
-    
-    while (fsm == 0) {
-        
-        manage_heater();
-        manage_inactivity(true);
-        
-        if ( abs((enc_dif - lcd_encoder_diff)) > 4 ) {
-            
-            if ( (abs(enc_dif - lcd_encoder_diff)) > 1 ) {
-                if (enc_dif > lcd_encoder_diff ) {
-                    cursor_pos --;
-                }
-                
-                if (enc_dif < lcd_encoder_diff  ) {
-                    cursor_pos ++;
-                }
-                
-                if (cursor_pos > 4) {
-                    cursor_pos = 4;
-                }
-                
-                if (cursor_pos < 1) {
-                    cursor_pos = 1;
-                }
-
-                
-                lcd_set_cursor(1, 2);
-                lcd_print(' ');
-                lcd_set_cursor(1, 3);
-                lcd_print(' ');
-                lcd_set_cursor(10, 2);
-                lcd_print(' ');
-                lcd_set_cursor(10, 3);
-                lcd_print(' ');
-                
-                if (cursor_pos < 3) {
-                    lcd_set_cursor(1, cursor_pos+1);
-                    lcd_print('>');
-                }else{
-                    lcd_set_cursor(10, cursor_pos-1);
-                    lcd_print('>');
-                }
-                
-   
-                enc_dif = lcd_encoder_diff;
-                _delay(100);
-            }
-            
-        }
-        
-        if (lcd_clicked()) {
-            fsm = cursor_pos;
-            int babyStepZ;
-            babyStepZ = eeprom_read_word((uint16_t*)EEPROM_BABYSTEP_Z0+(fsm-1));
-            eeprom_update_word((uint16_t*)EEPROM_BABYSTEP_Z, babyStepZ);
-            calibration_status_store(CALIBRATION_STATUS_CALIBRATED);
-            _delay(500);
-            
-        }
-    };
-    
-    lcd_clear();
-    lcd_return_to_status();
-}
-*/
 void lcd_move_menu_axis()
 {
 	MENU_BEGIN();
@@ -7910,71 +7563,6 @@ void ultralcd_init()
   lcd_encoder_diff = 0;
 }
 
-
-
-
-
-void lcd_printer_connected() {
-	printer_connected = true;
-}
-
-static void lcd_send_status() {
-	if (farm_mode && no_response && (NcTime.expired(NC_TIME * 1000))) {
-		//send important status messages periodicaly
-		prusa_statistics(important_status, saved_filament_type);
-		NcTime.start();
-#ifdef FARM_CONNECT_MESSAGE
-		lcd_connect_printer();
-#endif //FARM_CONNECT_MESSAGE
-	}
-}
-
-#ifdef FARM_CONNECT_MESSAGE
-static void lcd_connect_printer() {
-	lcd_update_enable(false);
-	lcd_clear();
-	
-	int i = 0;
-	int t = 0;
-	lcd_puts_at_P(0, 0, _i("Connect printer to")); 
-	lcd_puts_at_P(0, 1, _i("monitoring or hold"));
-	lcd_puts_at_P(0, 2, _i("the knob to continue"));
-	while (no_response) {
-		i++;
-		t++;		
-		delay_keep_alive(100);
-		proc_commands();
-		if (t == 10) {
-			prusa_statistics(important_status, saved_filament_type);
-			t = 0;
-		}
-		if (READ(BTN_ENC)) { //if button is not pressed
-			i = 0; 
-			lcd_puts_at_P(0, 3, PSTR("                    "));
-		}
-		if (i!=0) lcd_puts_at_P((i * 20) / (NC_BUTTON_LONG_PRESS * 10), 3, LCD_STR_SOLID_BLOCK[0]);
-		if (i == NC_BUTTON_LONG_PRESS * 10) {
-			no_response = false;
-		}
-	}
-	lcd_update_enable(true);
-	lcd_update(2);
-}
-#endif //FARM_CONNECT_MESSAGE
-
-void lcd_ping() { //chceck if printer is connected to monitoring when in farm mode
-	if (farm_mode) {
-		bool empty = cmd_buffer_empty();
-		if ((_millis() - PingTime) * 0.001 > (empty ? PING_TIME : PING_TIME_LONG)) { //if commands buffer is empty use shorter time period
-																							  //if there are comamnds in buffer, some long gcodes can delay execution of ping command
-																							  //therefore longer period is used
-			printer_connected = false;
-		}
-		else {
-			lcd_printer_connected();
-		}
-	}
-}
 void lcd_ignore_click(bool b)
 {
   ignore_click = b;
@@ -8220,8 +7808,7 @@ void menu_lcd_lcdupdate_func(void)
 		if (lcd_draw_update) lcd_draw_update--;
 		lcd_next_update_millis = _millis() + LCD_UPDATE_INTERVAL;
 	}
-	lcd_ping(); //check that we have received ping command if we are in farm mode
-	lcd_send_status();
+	prusa_statistics_update_from_lcd_update();
 	if (lcd_commands_type == LcdCommands::Layer1Cal) lcd_commands();
 }
 

Firmware/ultralcd.h

@@ -47,9 +47,7 @@ void lcd_pause_print();
 void lcd_pause_usb_print();
 void lcd_resume_print();
 void lcd_print_stop();
-void prusa_statistics(uint8_t _message, uint8_t _col_nr = 0);
 void lcd_load_filament_color_check();
-//void lcd_mylang();
 
 extern void lcd_belttest();
 extern bool lcd_selftest();
@@ -187,8 +185,6 @@ void mFilamentItemForce();
 void lcd_generic_preheat_menu();
 void unload_filament(bool automatic = false);
 
-void lcd_printer_connected();
-void lcd_ping();
 
 void lcd_wait_for_heater();
 void lcd_wait_for_cool_down();

Firmware/variants/1_75mm_MK25-RAMBo10a-E3Dv6full.h

@@ -151,7 +151,6 @@
 //#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
 //#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
 //#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
-//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
 //#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
 //#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
 //#define DEBUG_DISABLE_FANCHECK     //disable fan check (no ISR INT7, check disabled)
@@ -494,13 +493,6 @@
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 

Firmware/variants/1_75mm_MK25-RAMBo13a-E3Dv6full.h

@@ -152,7 +152,6 @@
 //#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
 //#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
 //#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
-//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
 //#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
 //#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
 //#define DEBUG_DISABLE_FANCHECK     //disable fan check (no ISR INT7, check disabled)
@@ -495,13 +494,6 @@
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 

Firmware/variants/1_75mm_MK25S-RAMBo10a-E3Dv6full.h

@@ -151,7 +151,6 @@
 //#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
 //#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
 //#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
-//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
 //#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
 //#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
 //#define DEBUG_DISABLE_FANCHECK     //disable fan check (no ISR INT7, check disabled)
@@ -494,13 +493,6 @@
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 

Firmware/variants/1_75mm_MK25S-RAMBo13a-E3Dv6full.h

@@ -152,7 +152,6 @@
 //#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
 //#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
 //#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
-//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
 //#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
 //#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
 //#define DEBUG_DISABLE_FANCHECK     //disable fan check (no ISR INT7, check disabled)
@@ -495,13 +494,6 @@
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 

Firmware/variants/1_75mm_MK3-EINSy10a-E3Dv6full.h

@@ -193,7 +193,6 @@
 //#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
 //#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
 //#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
-//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
 //#define DEBUG_DISABLE_FORCE_SELFTEST //disable force selftest
 //#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
 //#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
@@ -531,9 +530,6 @@
 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
 
-//connect message when communication with monitoring broken
-//#define FARM_CONNECT_MESSAGE
-
 /*-----------------------------------
  PREHEAT SETTINGS
  *------------------------------------*/
@@ -653,13 +649,6 @@
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 

Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h

@@ -195,7 +195,6 @@
 //#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
 //#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
 //#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
-//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
 //#define DEBUG_DISABLE_FORCE_SELFTEST //disable force selftest
 //#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
 //#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
@@ -535,9 +534,6 @@
 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
 
-//connect message when communication with monitoring broken
-//#define FARM_CONNECT_MESSAGE
-
 /*-----------------------------------
  PREHEAT SETTINGS
  *------------------------------------*/
@@ -657,13 +653,6 @@
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 

Firmware/variants/obsolete/1_75mm_MK2-RAMBo10a-E3Dv6full.h

@@ -419,19 +419,11 @@ THERMISTORS SETTINGS
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press 
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 
 #define DEFAULT_PID_TEMP 210
 
-
 #define END_FILE_SECTION 20000 //number of bytes from end of file used for checking if file is complete
 
 // Safety timer

Firmware/variants/obsolete/1_75mm_MK2-RAMBo13a-E3Dv6full.h

@@ -408,19 +408,11 @@ THERMISTORS SETTINGS
 #define PINDA_STEP_T 10
 #define PINDA_MAX_T 100
 
-#define PING_TIME 60 //time in s
-#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
-#define PING_ALLERT_PERIOD 60 //time in s
-
-#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
-#define NC_BUTTON_LONG_PRESS 15 //time in s
-
 #define LONG_PRESS_TIME 1000 //time in ms for button long press 
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 
 #define DEFAULT_PID_TEMP 210
 
-
 #define END_FILE_SECTION 20000 //number of bytes from end of file used for checking if file is complete
 
 // Safety timer