Merge pull request #1627 from MRprusa3d/PFW-790

print parameters checking

Firmware/Marlin.h

@@ -214,6 +214,9 @@ void manage_inactivity(bool ignore_stepper_queue=false);
 #endif
 
 
+#define FARM_FILAMENT_COLOR_NONE 99;
+
+
 enum AxisEnum {X_AXIS=0, Y_AXIS=1, Z_AXIS=2, E_AXIS=3, X_HEAD=4, Y_HEAD=5};
 #define X_AXIS_MASK  1
 #define Y_AXIS_MASK  2

Firmware/Marlin_main.cpp

@@ -214,8 +214,6 @@ static LongTimer crashDetTimer;
 bool mesh_bed_leveling_flag = false;
 bool mesh_bed_run_from_menu = false;
 
-int8_t FarmMode = 0;
-
 bool prusa_sd_card_upload = false;
 
 unsigned int status_number = 0;
@@ -1065,6 +1063,9 @@ void setup()
 		//disabled filament autoload (PFW360)
 		fsensor_autoload_set(false);
 #endif //FILAMENT_SENSOR
+          // ~ FanCheck -> on
+          if(!(eeprom_read_byte((uint8_t*)EEPROM_FAN_CHECK_ENABLED)))
+               eeprom_update_byte((unsigned char *)EEPROM_FAN_CHECK_ENABLED,true);
 	}
 	MYSERIAL.begin(BAUDRATE);
 	fdev_setup_stream(uartout, uart_putchar, NULL, _FDEV_SETUP_WRITE); //setup uart out stream
@@ -1644,6 +1645,7 @@ void setup()
 	   
   }
 #endif //UVLO_SUPPORT
+  fCheckModeInit();
   KEEPALIVE_STATE(NOT_BUSY);
 #ifdef WATCHDOG
   wdt_enable(WDTO_4S);
@@ -3649,7 +3651,39 @@ void process_commands()
     } else if(code_seen("FR")) { //! PRUSA FR
         // Factory full reset
         factory_reset(0);
-    }
+
+//-//
+/*
+    } else if(code_seen("qqq")) {
+MYSERIAL.println("=== checking ===");
+MYSERIAL.println(eeprom_read_byte((uint8_t*)EEPROM_CHECK_MODE),DEC);
+MYSERIAL.println(eeprom_read_byte((uint8_t*)EEPROM_NOZZLE_DIAMETER),DEC);
+MYSERIAL.println(eeprom_read_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM),DEC);
+MYSERIAL.println(farm_mode,DEC);
+MYSERIAL.println(eCheckMode,DEC);
+    } else if(code_seen("www")) {
+MYSERIAL.println("=== @ FF ===");
+eeprom_update_byte((uint8_t*)EEPROM_CHECK_MODE,0xFF);
+eeprom_update_byte((uint8_t*)EEPROM_NOZZLE_DIAMETER,0xFF);
+eeprom_update_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM,0xFFFF);
+*/
+    } else if (code_seen("nozzle")) { //! PRUSA nozzle
+          uint16_t nDiameter;
+          if(code_seen('D'))
+               {
+               nDiameter=(uint16_t)(code_value()*1000.0+0.5); // [,um]
+               nozzle_diameter_check(nDiameter);
+               }
+          else if(code_seen("set") && farm_mode)
+               {
+               strchr_pointer++;                  // skip 2nd char (~ 'e')
+               strchr_pointer++;                  // skip 3rd char (~ 't')
+               nDiameter=(uint16_t)(code_value()*1000.0+0.5); // [,um]
+               eeprom_update_byte((uint8_t*)EEPROM_NOZZLE_DIAMETER,(uint8_t)e_NOZZLE_DIAMETER_NULL); // for correct synchronization after farm-mode exiting
+               eeprom_update_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM,nDiameter);
+               }
+          else SERIAL_PROTOCOLLN((float)eeprom_read_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM)/1000.0);
+	}	
     //else if (code_seen('Cal')) {
 		//  lcd_calibration();
 	  // }
@@ -4959,6 +4993,7 @@ if((eSoundMode==e_SOUND_MODE_LOUD)||(eSoundMode==e_SOUND_MODE_ONCE))
 		EEPROM_save_B(EEPROM_FARM_NUMBER, &farm_no);
           SilentModeMenu = SILENT_MODE_OFF;
           eeprom_update_byte((unsigned char *)EEPROM_SILENT, SilentModeMenu);
+          fCheckModeInit();                       // alternatively invoke printer reset
 		break;
 
 	case 99: //! G99 (deactivate farm mode)
@@ -4966,6 +5001,7 @@ if((eSoundMode==e_SOUND_MODE_LOUD)||(eSoundMode==e_SOUND_MODE_ONCE))
 		lcd_printer_connected();
 		eeprom_update_byte((unsigned char *)EEPROM_FARM_MODE, farm_mode);
 		lcd_update(2);
+          fCheckModeInit();                       // alternatively invoke printer reset
 		break;
 	default:
 		printf_P(PSTR("Unknown G code: %s \n"), cmdbuffer + bufindr + CMDHDRSIZE);
@@ -7671,7 +7707,7 @@ static void handleSafetyTimer()
     {
         safetyTimer.start();
     }
-    else if (safetyTimer.expired(safetytimer_inactive_time))
+    else if (safetyTimer.expired(farm_mode?FARM_DEFAULT_SAFETYTIMER_TIME_ms:safetytimer_inactive_time))
     {
         setTargetBed(0);
         setAllTargetHotends(0);

Firmware/eeprom.h

@@ -155,11 +155,18 @@
 #define EEPROM_MMU_LOAD_FAIL (EEPROM_MMU_LOAD_FAIL_TOT - 1) //uint8_t
 #define EEPROM_MMU_CUTTER_ENABLED (EEPROM_MMU_LOAD_FAIL - 1)
 #define EEPROM_UVLO_MESH_BED_LEVELING_FULL     (EEPROM_MMU_CUTTER_ENABLED - 12*12*2) //allow 12 calibration points for future expansion
+
 #define EEPROM_MBL_TYPE	(EEPROM_UVLO_MESH_BED_LEVELING_FULL-1) //uint8_t for mesh bed leveling precision
 #define EEPROM_MBL_MAGNET_ELIMINATION (EEPROM_MBL_TYPE -1)  
 #define EEPROM_MBL_POINTS_NR (EEPROM_MBL_MAGNET_ELIMINATION -1) //uint8_t number of points in one exis for mesh bed leveling
 #define EEPROM_MBL_PROBE_NR (EEPROM_MBL_POINTS_NR-1) //number of measurements for each point
+
 #define EEPROM_MMU_STEALTH (EEPROM_MBL_PROBE_NR-1)
+
+#define EEPROM_CHECK_MODE (EEPROM_MMU_STEALTH-1) // uint8
+#define EEPROM_NOZZLE_DIAMETER (EEPROM_CHECK_MODE-1) // uint8
+#define EEPROM_NOZZLE_DIAMETER_uM (EEPROM_NOZZLE_DIAMETER-2) // uint16
+
 // !!!!!
 // !!!!! this is end of EEPROM section ... all updates MUST BE inserted before this mark !!!!!
 // !!!!!

Firmware/ultralcd.cpp

@@ -131,6 +131,7 @@ static void lcd_control_volumetric_menu();
 static void lcd_settings_linearity_correction_menu_save();
 static void prusa_stat_printerstatus(int _status);
 static void prusa_stat_farm_number();
+static void prusa_stat_diameter();
 static void prusa_stat_temperatures();
 static void prusa_stat_printinfo();
 static void lcd_farm_no();
@@ -2023,7 +2024,6 @@ static void lcd_preheat_menu()
 	  MENU_ITEM_FUNCTION_P(PSTR("farm   -  " STRINGIFY(FARM_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(FARM_PREHEAT_HPB_TEMP)), lcd_preheat_farm);
 	  MENU_ITEM_FUNCTION_P(PSTR("nozzle -  " STRINGIFY(FARM_PREHEAT_HOTEND_TEMP) "/0"), lcd_preheat_farm_nozzle);
 	  MENU_ITEM_FUNCTION_P(_T(MSG_COOLDOWN), lcd_cooldown);
-	  MENU_ITEM_FUNCTION_P(PSTR("ABS    -  " STRINGIFY(ABS_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(ABS_PREHEAT_HPB_TEMP)), lcd_preheat_abs);
   } else {
 	  MENU_ITEM_FUNCTION_P(PSTR("PLA  -  " STRINGIFY(PLA_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PLA_PREHEAT_HPB_TEMP)), lcd_preheat_pla);
 	  MENU_ITEM_FUNCTION_P(PSTR("PET  -  " STRINGIFY(PET_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PET_PREHEAT_HPB_TEMP)), lcd_preheat_pet);
@@ -3980,6 +3980,7 @@ void prusa_statistics(int _message, uint8_t _fil_nr) {
 			SERIAL_ECHO("{");
 			prusa_stat_printerstatus(1);
 			prusa_stat_farm_number();
+			prusa_stat_diameter();
 			SERIAL_ECHOLN("}");
 			status_number = 1;
 		}
@@ -4134,6 +4135,12 @@ static void prusa_stat_farm_number() {
 	SERIAL_ECHO("]");
 }
 
+static void prusa_stat_diameter() {
+	SERIAL_ECHO("[DIA:");
+	SERIAL_ECHO(eeprom_read_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM));
+	SERIAL_ECHO("]");
+}
+
 static void prusa_stat_temperatures()
 {
 	SERIAL_ECHO("[ST0:");
@@ -4169,6 +4176,7 @@ static void prusa_stat_printinfo()
 	SERIAL_ECHO("][FWR:");
 	SERIAL_ECHO(FW_VERSION);
 	SERIAL_ECHO("]");
+     prusa_stat_diameter();
 }
 
 /*
@@ -5277,6 +5285,101 @@ do\
 }\
 while (0)
 
+//-//
+static void lcd_check_mode_set(void)
+{
+switch(eCheckMode)
+     {
+     case e_CHECK_MODE_none:
+          eCheckMode=e_CHECK_MODE_warn;
+          break;
+     case e_CHECK_MODE_warn:
+          eCheckMode=e_CHECK_MODE_strict;
+          break;
+     case e_CHECK_MODE_strict:
+          eCheckMode=e_CHECK_MODE_none;
+          break;
+     default:
+          eCheckMode=e_CHECK_MODE_none;
+     }
+eeprom_update_byte((uint8_t*)EEPROM_CHECK_MODE,(uint8_t)eCheckMode);
+}
+
+static void lcd_nozzle_diameter_set(void)
+{
+uint16_t nDiameter;
+
+switch(eNozzleDiameter)
+     {
+     case e_NOZZLE_DIAMETER_250:
+          eNozzleDiameter=e_NOZZLE_DIAMETER_400;
+          nDiameter=400;
+          break;
+     case e_NOZZLE_DIAMETER_400:
+          eNozzleDiameter=e_NOZZLE_DIAMETER_600;
+          nDiameter=600;
+          break;
+     case e_NOZZLE_DIAMETER_600:
+          eNozzleDiameter=e_NOZZLE_DIAMETER_250;
+          nDiameter=250;
+          break;
+     default:
+          eNozzleDiameter=e_NOZZLE_DIAMETER_400;
+          nDiameter=400;
+     }
+eeprom_update_byte((uint8_t*)EEPROM_NOZZLE_DIAMETER,(uint8_t)eNozzleDiameter);
+eeprom_update_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM,nDiameter);
+}
+
+#define SETTINGS_MODE \
+do\
+{\
+    switch(eCheckMode)\
+         {\
+         case e_CHECK_MODE_none:\
+              MENU_ITEM_FUNCTION_P(_i("Action     [none]"),lcd_check_mode_set);\
+              break;\
+         case e_CHECK_MODE_warn:\
+              MENU_ITEM_FUNCTION_P(_i("Action     [warn]"),lcd_check_mode_set);\
+              break;\
+         case e_CHECK_MODE_strict:\
+              MENU_ITEM_FUNCTION_P(_i("Action   [strict]"),lcd_check_mode_set);\
+              break;\
+         default:\
+              MENU_ITEM_FUNCTION_P(_i("Action     [none]"),lcd_check_mode_set);\
+         }\
+}\
+while (0)
+
+#define SETTINGS_NOZZLE \
+do\
+{\
+    switch(eNozzleDiameter)\
+         {\
+         case e_NOZZLE_DIAMETER_250:\
+              MENU_ITEM_FUNCTION_P(_i("Nozzle     [0.25]"),lcd_nozzle_diameter_set);\
+              break;\
+         case e_NOZZLE_DIAMETER_400:\
+              MENU_ITEM_FUNCTION_P(_i("Nozzle     [0.40]"),lcd_nozzle_diameter_set);\
+              break;\
+         case e_NOZZLE_DIAMETER_600:\
+              MENU_ITEM_FUNCTION_P(_i("Nozzle     [0.60]"),lcd_nozzle_diameter_set);\
+              break;\
+         default:\
+              MENU_ITEM_FUNCTION_P(_i("Nozzle     [0.40]"),lcd_nozzle_diameter_set);\
+         }\
+}\
+while (0)
+
+static void lcd_checking_menu()
+{
+MENU_BEGIN();
+MENU_ITEM_BACK_P(_T(MSG_SETTINGS));
+SETTINGS_MODE;
+SETTINGS_NOZZLE;
+MENU_END();
+}
+
 static void lcd_settings_menu()
 {
 	EEPROM_read(EEPROM_SILENT, (uint8_t*)&SilentModeMenu, sizeof(SilentModeMenu));
@@ -5328,6 +5431,9 @@ static void lcd_settings_menu()
 	MENU_ITEM_SUBMENU_P(_i("Select language"), lcd_language_menu);////MSG_LANGUAGE_SELECT
 #endif //(LANG_MODE != 0)
 
+	if (!farm_mode)
+          MENU_ITEM_SUBMENU_P(_i("Print checking"), lcd_checking_menu);
+
 	SETTINGS_SD;
 	SETTINGS_SOUND;
 
@@ -6140,10 +6246,11 @@ void lcd_confirm_print()
 		}
 		if (lcd_clicked())
 		{
+               filament_type = FARM_FILAMENT_COLOR_NONE;
 			if (cursor_pos == 1)
 			{
 				_ret = 1;
-				filament_type = lcd_choose_color();
+//				filament_type = lcd_choose_color();
 				prusa_statistics(4, filament_type);
 				no_response = true; //we need confirmation by recieving PRUSA thx
 				important_status = 4;
@@ -6153,7 +6260,7 @@ void lcd_confirm_print()
 			if (cursor_pos == 2)
 			{
 				_ret = 2;
-				filament_type = lcd_choose_color();
+//				filament_type = lcd_choose_color();
 				prusa_statistics(5, filament_type);
 				no_response = true; //we need confirmation by recieving PRUSA thx
 				important_status = 5;				
@@ -6488,6 +6595,14 @@ static void lcd_tune_menu()
 
 	SETTINGS_CUTTER;
 
+     if(farm_mode)
+     {
+          if (fans_check_enabled == true)
+               MENU_ITEM_FUNCTION_P(_i("Fans check   [on]"), lcd_set_fan_check);////MSG_FANS_CHECK_ON c=17 r=1
+          else
+               MENU_ITEM_FUNCTION_P(_i("Fans check  [off]"), lcd_set_fan_check);////MSG_FANS_CHECK_OFF c=17 r=1
+     }
+
 #ifdef TMC2130
      if(!farm_mode)
      {
@@ -6631,6 +6746,12 @@ static void lcd_sd_updir()
 
 void lcd_print_stop()
 {
+//-//
+     if(!card.sdprinting)
+          {
+          SERIAL_ECHOLNPGM("// action:cancel");   // for Octoprint
+          return;
+          }
 	saved_printing = false;
 	cancel_heatup = true;
 #ifdef MESH_BED_LEVELING

Firmware/ultralcd.h

@@ -147,14 +147,14 @@ void extr_unload();
 
 typedef enum
 {
-    e_FILAMENT_ACTION_none, //!< 'none' state is used as flag for (filament) autoLoad (i.e. opposite for 'autoLoad' state)
+    e_FILAMENT_ACTION_none,                       //!< 'none' state is used as flag for (filament) autoLoad (i.e. opposite for 'autoLoad' state)
     e_FILAMENT_ACTION_Load,
     e_FILAMENT_ACTION_autoLoad,
     e_FILAMENT_ACTION_unLoad,
     e_FILAMENT_ACTION_mmuLoad,
     e_FILAMENT_ACTION_mmuUnLoad,
     e_FILAMENT_ACTION_mmuEject,
-    e_FILAMENT_ACTION_mmuCut,
+    e_FILAMENT_ACTION_mmuCut
 } eFILAMENT_ACTION;
 extern eFILAMENT_ACTION eFilamentAction;
 extern bool bFilamentFirstRun;

Firmware/util.cpp

@@ -327,3 +327,46 @@ void update_current_firmware_version_to_eeprom()
         eeprom_update_word((uint16_t*)EEPROM_FIRMWARE_VERSION_FLAVOR,   ver_current[3]);
     }
 }
+
+
+//-//
+eNOZZLE_DIAMETER eNozzleDiameter=e_NOZZLE_DIAMETER_400;
+eCHECK_MODE eCheckMode=e_CHECK_MODE_none;
+
+void fCheckModeInit()
+{
+eCheckMode=(eCHECK_MODE)eeprom_read_byte((uint8_t*)EEPROM_CHECK_MODE);
+if(eCheckMode==e_CHECK_MODE_NULL)
+     {
+     eCheckMode=e_CHECK_MODE_warn;
+     eeprom_update_byte((uint8_t*)EEPROM_CHECK_MODE,(uint8_t)eCheckMode);
+     }
+if(farm_mode)
+     eCheckMode=e_CHECK_MODE_strict;
+eNozzleDiameter=(eNOZZLE_DIAMETER)eeprom_read_byte((uint8_t*)EEPROM_NOZZLE_DIAMETER);
+if((eNozzleDiameter==e_NOZZLE_DIAMETER_NULL)&& !farm_mode)
+     {
+     eNozzleDiameter=e_NOZZLE_DIAMETER_400;
+     eeprom_update_byte((uint8_t*)EEPROM_NOZZLE_DIAMETER,(uint8_t)eNozzleDiameter);
+     eeprom_update_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM,400);
+     }
+}
+
+void nozzle_diameter_check(uint16_t nDiameter)
+{
+uint16_t nDiameter_um;
+
+nDiameter_um=eeprom_read_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM);
+if(nDiameter==nDiameter_um)
+     return;
+switch(eCheckMode)
+     {
+     case e_CHECK_MODE_warn:
+          lcd_show_fullscreen_message_and_wait_P(_i("Nozzle diameter doesn't match! Press the knob to continue."));
+          break;
+     case e_CHECK_MODE_strict:
+          lcd_show_fullscreen_message_and_wait_P(_i("Nozzle diameter doesn't match! Print is aborted, press the knob."));
+          lcd_print_stop();
+          break;
+     }
+}

Firmware/util.h

@@ -33,4 +33,29 @@ inline void eeprom_update_int8(unsigned char* addr, int8_t v) {
 	eeprom_update_byte(addr, *reinterpret_cast<uint8_t*>(&v));
 }
 
+
+//-//
+#define e_CHECK_MODE_NULL 0xFF
+#define e_NOZZLE_DIAMETER_NULL 0xFF
+
+typedef enum
+{
+    e_NOZZLE_DIAMETER_250,
+    e_NOZZLE_DIAMETER_400,
+    e_NOZZLE_DIAMETER_600
+} eNOZZLE_DIAMETER;
+
+typedef enum
+{
+    e_CHECK_MODE_none,
+    e_CHECK_MODE_warn,
+    e_CHECK_MODE_strict
+} eCHECK_MODE;
+
+extern eNOZZLE_DIAMETER eNozzleDiameter;
+extern eCHECK_MODE eCheckMode;
+
+void fCheckModeInit();
+void nozzle_diameter_check(uint16_t nDiameter);
+
 #endif /* UTIL_H */

Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h

@@ -315,7 +315,7 @@ PREHEAT SETTINGS
 *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
@@ -438,6 +438,7 @@ THERMISTORS SETTINGS
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 #define M600_TIMEOUT 600  //seconds
 

Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h

@@ -314,7 +314,7 @@ PREHEAT SETTINGS
 *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
@@ -437,6 +437,7 @@ THERMISTORS SETTINGS
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 #define M600_TIMEOUT 600  //seconds
 

Firmware/variants/1_75mm_MK25-RAMBo10a-E3Dv6full.h

@@ -112,6 +112,7 @@
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 // Filament sensor
 #define FILAMENT_SENSOR
@@ -371,7 +372,7 @@
  *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215

Firmware/variants/1_75mm_MK25-RAMBo13a-E3Dv6full.h

@@ -113,6 +113,7 @@
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 // Filament sensor
 #define FILAMENT_SENSOR
@@ -372,7 +373,7 @@
  *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215

Firmware/variants/1_75mm_MK25S-RAMBo10a-E3Dv6full.h

@@ -112,6 +112,7 @@
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 // Filament sensor
 #define FILAMENT_SENSOR
@@ -371,7 +372,7 @@
  *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215

Firmware/variants/1_75mm_MK25S-RAMBo13a-E3Dv6full.h

@@ -113,6 +113,7 @@
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 // Filament sensor
 #define FILAMENT_SENSOR
@@ -372,7 +373,7 @@
  *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215

Firmware/variants/1_75mm_MK3-EINSy10a-E3Dv6full.h

@@ -131,6 +131,7 @@
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 // Filament sensor
 #define FILAMENT_SENSOR
@@ -480,7 +481,7 @@
  *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 60
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215

Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h

@@ -131,6 +131,7 @@
 // Safety timer
 #define SAFETYTIMER
 #define DEFAULT_SAFETYTIMER_TIME_MINS 30
+#define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
 
 // Filament sensor
 #define FILAMENT_SENSOR
@@ -480,7 +481,7 @@
  *------------------------------------*/
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
-#define FARM_PREHEAT_HPB_TEMP 60
+#define FARM_PREHEAT_HPB_TEMP 80
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215