Merge remote-tracking branch 'upstream/MK3' into MK3

Firmware/Marlin.h

@@ -323,7 +323,6 @@ extern float retract_recover_length_swap;
 
 extern uint8_t host_keepalive_interval;
 
-
 extern unsigned long starttime;
 extern unsigned long stoptime;
 extern int bowden_length[4];

Firmware/Marlin_main.cpp

@@ -1076,6 +1076,7 @@ void setup()
 	SERIAL_ECHO_START;
 	printf_P(PSTR(" " FW_VERSION_FULL "\n"));
 
+	//SERIAL_ECHOPAIR("Active sheet before:", static_cast<unsigned long int>(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet))));
 
 #ifdef DEBUG_SEC_LANG
 	lang_table_header_t header;
@@ -1424,20 +1425,7 @@ void setup()
 		printf_P(PSTR("Card NG!\n"));
 #endif //DEBUG_SD_SPEED_TEST
 
-	if (eeprom_read_byte((uint8_t*)EEPROM_POWER_COUNT) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_POWER_COUNT, 0);
-	if (eeprom_read_byte((uint8_t*)EEPROM_CRASH_COUNT_X) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_CRASH_COUNT_X, 0);
-	if (eeprom_read_byte((uint8_t*)EEPROM_CRASH_COUNT_Y) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_CRASH_COUNT_Y, 0);
-	if (eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_FERROR_COUNT, 0);
-	if (eeprom_read_word((uint16_t*)EEPROM_POWER_COUNT_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_POWER_COUNT_TOT, 0);
-	if (eeprom_read_word((uint16_t*)EEPROM_CRASH_COUNT_X_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_CRASH_COUNT_X_TOT, 0);
-	if (eeprom_read_word((uint16_t*)EEPROM_CRASH_COUNT_Y_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_CRASH_COUNT_Y_TOT, 0);
-	if (eeprom_read_word((uint16_t*)EEPROM_FERROR_COUNT_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_FERROR_COUNT_TOT, 0);
-
-	if (eeprom_read_word((uint16_t*)EEPROM_MMU_FAIL_TOT) == 0xffff) eeprom_update_word((uint16_t *)EEPROM_MMU_FAIL_TOT, 0);
-	if (eeprom_read_word((uint16_t*)EEPROM_MMU_LOAD_FAIL_TOT) == 0xffff) eeprom_update_word((uint16_t *)EEPROM_MMU_LOAD_FAIL_TOT, 0);
-	if (eeprom_read_byte((uint8_t*)EEPROM_MMU_FAIL) == 0xff) eeprom_update_byte((uint8_t *)EEPROM_MMU_FAIL, 0);
-	if (eeprom_read_byte((uint8_t*)EEPROM_MMU_LOAD_FAIL) == 0xff) eeprom_update_byte((uint8_t *)EEPROM_MMU_LOAD_FAIL, 0);
-
+    eeprom_init();
 #ifdef SNMM
 	if (eeprom_read_dword((uint32_t*)EEPROM_BOWDEN_LENGTH) == 0x0ffffffff) { //bowden length used for SNMM
 	  int _z = BOWDEN_LENGTH;
@@ -1504,7 +1492,6 @@ void setup()
 		SilentModeMenu_MMU = 1;
 		eeprom_write_byte((uint8_t*)EEPROM_MMU_STEALTH, SilentModeMenu_MMU);
 	}
-	check_babystep(); //checking if Z babystep is in allowed range
 
 #if !defined(DEBUG_DISABLE_FANCHECK) && defined(FANCHECK) && defined(TACH_1) && TACH_1 >-1
 	setup_fan_interrupt();
@@ -1650,7 +1637,6 @@ void setup()
 #ifdef WATCHDOG
   wdt_enable(WDTO_4S);
 #endif //WATCHDOG
-
 }
 
 
@@ -8159,12 +8145,15 @@ static void wait_for_heater(long codenum, uint8_t extruder) {
 
 void check_babystep()
 {
-	int babystep_z;
-	EEPROM_read_B(EEPROM_BABYSTEP_Z, &babystep_z);
+	int babystep_z = eeprom_read_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->
+            s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))].z_offset)));
+
 	if ((babystep_z < Z_BABYSTEP_MIN) || (babystep_z > Z_BABYSTEP_MAX)) {
 		babystep_z = 0; //if babystep value is out of min max range, set it to 0
 		SERIAL_ECHOLNPGM("Z live adjust out of range. Setting to 0");
-		EEPROM_save_B(EEPROM_BABYSTEP_Z, &babystep_z);
+		eeprom_write_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->
+            s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))].z_offset)),
+                    babystep_z);
 		lcd_show_fullscreen_message_and_wait_P(PSTR("Z live adjust out of range. Setting to 0. Click to continue."));
 		lcd_update_enable(true);		
 	}	

Firmware/eeprom.cpp

@@ -0,0 +1,83 @@
+//! @file
+//! @date Jun 20, 2019
+//! @author Marek Běl
+
+#include "eeprom.h"
+#include "Marlin.h"
+
+#include <avr/eeprom.h>
+#include <stdint.h>
+
+
+#include "language.h"
+
+#if 0
+template <typename T>
+static T eeprom_read(T *address);
+
+template<>
+char eeprom_read<char>(char *address)
+{
+    return eeprom_read_byte(reinterpret_cast<uint8_t*>(address));
+}
+#endif
+
+template <typename T>
+static void eeprom_write(T *address, T value);
+
+template<>
+void eeprom_write<char>(char *addres, char value)
+{
+    eeprom_write_byte(reinterpret_cast<uint8_t*>(addres), static_cast<uint8_t>(value));
+}
+
+
+template <typename T>
+static bool eeprom_is_uninitialized(T *address);
+
+template <>
+bool eeprom_is_uninitialized<char>(char *address)
+{
+    return (0xff == eeprom_read_byte(reinterpret_cast<uint8_t*>(address)));
+}
+
+bool is_sheet_initialized(){
+  return (0xffff != eeprom_read_word(reinterpret_cast<uint16_t*>(&(EEPROM_Sheets_base->
+  s[eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet))].z_offset))));
+}
+
+void eeprom_init()
+{
+    if (eeprom_read_byte((uint8_t*)EEPROM_POWER_COUNT) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_POWER_COUNT, 0);
+    if (eeprom_read_byte((uint8_t*)EEPROM_CRASH_COUNT_X) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_CRASH_COUNT_X, 0);
+    if (eeprom_read_byte((uint8_t*)EEPROM_CRASH_COUNT_Y) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_CRASH_COUNT_Y, 0);
+    if (eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT) == 0xff) eeprom_write_byte((uint8_t*)EEPROM_FERROR_COUNT, 0);
+    if (eeprom_read_word((uint16_t*)EEPROM_POWER_COUNT_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_POWER_COUNT_TOT, 0);
+    if (eeprom_read_word((uint16_t*)EEPROM_CRASH_COUNT_X_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_CRASH_COUNT_X_TOT, 0);
+    if (eeprom_read_word((uint16_t*)EEPROM_CRASH_COUNT_Y_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_CRASH_COUNT_Y_TOT, 0);
+    if (eeprom_read_word((uint16_t*)EEPROM_FERROR_COUNT_TOT) == 0xffff) eeprom_write_word((uint16_t*)EEPROM_FERROR_COUNT_TOT, 0);
+
+    if (eeprom_read_word((uint16_t*)EEPROM_MMU_FAIL_TOT) == 0xffff) eeprom_update_word((uint16_t *)EEPROM_MMU_FAIL_TOT, 0);
+    if (eeprom_read_word((uint16_t*)EEPROM_MMU_LOAD_FAIL_TOT) == 0xffff) eeprom_update_word((uint16_t *)EEPROM_MMU_LOAD_FAIL_TOT, 0);
+    if (eeprom_read_byte((uint8_t*)EEPROM_MMU_FAIL) == 0xff) eeprom_update_byte((uint8_t *)EEPROM_MMU_FAIL, 0);
+    if (eeprom_read_byte((uint8_t*)EEPROM_MMU_LOAD_FAIL) == 0xff) eeprom_update_byte((uint8_t *)EEPROM_MMU_LOAD_FAIL, 0);
+    if (eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)) == 0xff) eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), 0);
+    for (uint_least8_t i = 0; i < (sizeof(Sheets::s)/sizeof(Sheets::s[0])); ++i)
+    {
+        bool is_uninitialized = true;
+        for (uint_least8_t j = 0; j < (sizeof(Sheet::name)/sizeof(Sheet::name[0])); ++j)
+        {
+            if (!eeprom_is_uninitialized(&(EEPROM_Sheets_base->s[i].name[j]))) is_uninitialized = false;
+        }
+        if(is_uninitialized)
+        {
+            eeprom_write(&(EEPROM_Sheets_base->s[i].name[0]), static_cast<char>(i + '1'));
+            eeprom_write(&(EEPROM_Sheets_base->s[i].name[1]), '\0');
+        }
+    }
+    check_babystep();
+}
+
+
+
+

Firmware/eeprom.h

@@ -1,6 +1,10 @@
 #ifndef EEPROM_H
 #define EEPROM_H
 
+#include <stdint.h>
+
+void eeprom_init();
+
 // The total size of the EEPROM is
 // 4096 for the Atmega2560
 #define EEPROM_TOP 4096
@@ -167,31 +171,38 @@
 #define EEPROM_NOZZLE_DIAMETER (EEPROM_CHECK_MODE-1) // uint8
 #define EEPROM_NOZZLE_DIAMETER_uM (EEPROM_NOZZLE_DIAMETER-2) // uint16
 
+typedef struct
+{
+    char name[7];     //!< Can be null terminated, doesn't need to be null terminated
+    int16_t z_offset; //!< Z_BABYSTEP_MIN .. Z_BABYSTEP_MAX = Z_BABYSTEP_MIN*2/1000 [mm] .. Z_BABYSTEP_MAX*2/1000 [mm]
+    uint8_t bed_temp; //!< 0 .. 254 [°C]
+    uint8_t pinda_temp; //!< 0 .. 254 [°C]
+} Sheet;
+
+typedef struct
+{
+    Sheet s[3];
+    uint8_t active_sheet;
+} Sheets;
+// sizeof(Sheets). Do not change it unless EEPROM_Sheets_base is last item in EEPROM.
+// Otherwise it would move following items.
+#define EEPROM_SHEETS_SIZEOF 34
+
+static Sheets * const EEPROM_Sheets_base = (Sheets*)(EEPROM_NOZZLE_DIAMETER - EEPROM_SHEETS_SIZEOF);
+
+#ifdef __cplusplus
+extern bool is_sheet_initialized();
+static_assert(sizeof(Sheets) == EEPROM_SHEETS_SIZEOF, "Sizeof(Sheets) is not EEPROM_SHEETS_SIZEOF.");
+#endif
+
+//This is supposed to point to last item to allow EEPROM overrun check. Please update when adding new items.
+#define EEPROM_LAST_ITEM ((uint16_t)EEPROM_Sheets_base)
+
 // !!!!!
 // !!!!! this is end of EEPROM section ... all updates MUST BE inserted before this mark !!!!!
 // !!!!!
 
-//TMC2130 configuration
-#define EEPROM_TMC_AXIS_SIZE  //axis configuration block size
-#define EEPROM_TMC_X (EEPROM_TMC + 0 * EEPROM_TMC_AXIS_SIZE) //X axis configuration blok
-#define EEPROM_TMC_Y (EEPROM_TMC + 1 * EEPROM_TMC_AXIS_SIZE) //Y axis
-#define EEPROM_TMC_Z (EEPROM_TMC + 2 * EEPROM_TMC_AXIS_SIZE) //Z axis
-#define EEPROM_TMC_E (EEPROM_TMC + 3 * EEPROM_TMC_AXIS_SIZE) //E axis
-//TMC2130 - X axis
-#define EEPROM_TMC_X_USTEPS_INTPOL   (EEPROM_TMC_X +  0) // 1byte, bit 0..4 USTEPS, bit 7 INTPOL
-#define EEPROM_TMC_X_PWM_AMPL        (EEPROM_TMC_X +  1) // 1byte (0..255)
-#define EEPROM_TMC_X_PWM_GRAD_FREQ   (EEPROM_TMC_X +  2) // 1byte, bit 0..3 GRAD, bit 4..5 FREQ
-#define EEPROM_TMC_X_TCOOLTHRS       (EEPROM_TMC_X +  3) // 2bytes (0..)
-#define EEPROM_TMC_X_SG_THRS         (EEPROM_TMC_X +  5) // 1byte, (-64..+63)
-#define EEPROM_TMC_X_CURRENT_H       (EEPROM_TMC_X +  6) // 1byte, (0..63)
-#define EEPROM_TMC_X_CURRENT_R       (EEPROM_TMC_X +  7) // 1byte, (0..63)
-#define EEPROM_TMC_X_HOME_SG_THRS    (EEPROM_TMC_X +  8) // 1byte, (-64..+63)
-#define EEPROM_TMC_X_HOME_CURRENT_R  (EEPROM_TMC_X +  9) // 1byte, (-64..+63)
-#define EEPROM_TMC_X_HOME_DTCOOLTHRS (EEPROM_TMC_X + 10) // 1byte (-128..+127)
-#define EEPROM_TMC_X_DTCOOLTHRS_LOW  (EEPROM_TMC_X + 11) // 1byte (-128..+127)
-#define EEPROM_TMC_X_DTCOOLTHRS_HIGH (EEPROM_TMC_X + 12) // 1byte (-128..+127)
-#define EEPROM_TMC_X_SG_THRS_LOW     (EEPROM_TMC_X + 13) // 1byte, (-64..+63)
-#define EEPROM_TMC_X_SG_THRS_HIGH    (EEPROM_TMC_X + 14) // 1byte, (-64..+63)
+
 
 // Currently running firmware, each digit stored as uint16_t.
 // The flavor differentiates a dev, alpha, beta, release candidate or a release version.
@@ -205,7 +216,9 @@
 
 #ifdef __cplusplus
 #include "ConfigurationStore.h"
-static M500_conf * const EEPROM_M500_base = reinterpret_cast<M500_conf*>(20); //offset for storing settings using M500
+static_assert(EEPROM_FIRMWARE_VERSION_END < 20, "Firmware version EEPROM address conflicts with EEPROM_M500_base");
+static constexpr M500_conf * const EEPROM_M500_base = reinterpret_cast<M500_conf*>(20); //offset for storing settings using M500
+static_assert(((sizeof(M500_conf) + 20) < EEPROM_LAST_ITEM), "M500_conf address space conflicts with previous items.");
 #endif
 
 enum

Firmware/menu.cpp

@@ -168,16 +168,40 @@ int menu_draw_item_printf_P(char type_char, const char* format, ...)
 }
 */
 
+static char menu_selection_mark(){
+	return (lcd_encoder == menu_item)?'>':' ';
+}
+
 static void menu_draw_item_puts_P(char type_char, const char* str)
 {
     lcd_set_cursor(0, menu_row);
-    lcd_printf_P(PSTR("%c%-18.18S%c"), (lcd_encoder == menu_item)?'>':' ', str, type_char);
+    lcd_printf_P(PSTR("%c%-18.18S%c"), menu_selection_mark(), str, type_char);
+}
+
+//! @brief Format sheet name
+//!
+//! @param[in] sheet_E Sheet in EEPROM
+//! @param[out] buffer for formatted output
+void menu_format_sheet_E(const Sheet &sheet_E, SheetFormatBuffer &buffer)
+{
+    uint_least8_t index = sprintf_P(buffer.c, PSTR("%.10S "), _T(MSG_SHEET));
+    eeprom_read_block(&(buffer.c[index]), sheet_E.name, 7);
+    //index += 7;
+    buffer.c[index + 7] = '\0';
+}
+
+static void menu_draw_item_puts_E(char type_char, const Sheet &sheet)
+{
+    lcd_set_cursor(0, menu_row);
+    SheetFormatBuffer buffer;
+    menu_format_sheet_E(sheet, buffer);
+    lcd_printf_P(PSTR("%c%-18.18s%c"), menu_selection_mark(), buffer.c, type_char);
 }
 
 static void menu_draw_item_puts_P(char type_char, const char* str, char num)
 {
     lcd_set_cursor(0, menu_row);
-    lcd_printf_P(PSTR("%c%-.16S "), (lcd_encoder == menu_item)?'>':' ', str);
+    lcd_printf_P(PSTR("%c%-.16S "), menu_selection_mark(), str);
     lcd_putc(num);
     lcd_set_cursor(19, menu_row);
     lcd_putc(type_char);
@@ -224,6 +248,21 @@ uint8_t menu_item_submenu_P(const char* str, menu_func_t submenu)
 	return 0;
 }
 
+uint8_t menu_item_submenu_E(const Sheet &sheet, menu_func_t submenu)
+{
+    if (menu_item == menu_line)
+    {
+        if (lcd_draw_update) menu_draw_item_puts_E(LCD_STR_ARROW_RIGHT[0], sheet);
+        if (menu_clicked && (lcd_encoder == menu_item))
+        {
+            menu_submenu(submenu);
+            return menu_item_ret();
+        }
+    }
+    menu_item++;
+    return 0;
+}
+
 uint8_t menu_item_back_P(const char* str)
 {
 	if (menu_item == menu_line)
@@ -399,7 +438,7 @@ uint8_t menu_item_edit_P(const char* str, T pval, int16_t min_val, int16_t max_v
 		if (lcd_draw_update) 
 		{
 			lcd_set_cursor(0, menu_row);
-			menu_draw_P<T>((lcd_encoder == menu_item)?'>':' ', str, *pval);
+			menu_draw_P<T>(menu_selection_mark(), str, *pval);
 		}
 		if (menu_clicked && (lcd_encoder == menu_item))
 		{

Firmware/menu.h

@@ -3,6 +3,7 @@
 #define _MENU_H
 
 #include <inttypes.h>
+#include "eeprom.h"
 
 #define MENU_DATA_SIZE      32
 
@@ -99,6 +100,10 @@ extern uint8_t menu_item_text_P(const char* str);
 #define MENU_ITEM_SUBMENU_P(str, submenu) do { if (menu_item_submenu_P(str, submenu)) return; } while (0)
 extern uint8_t menu_item_submenu_P(const char* str, menu_func_t submenu);
 
+#define MENU_ITEM_SUBMENU_E(sheet, submenu) do { if (menu_item_submenu_E(sheet, submenu)) return; } while (0)
+extern uint8_t menu_item_submenu_E(const Sheet &sheet, menu_func_t submenu);
+
+
 #define MENU_ITEM_BACK_P(str) do { if (menu_item_back_P(str)) return; } while (0)
 extern uint8_t menu_item_back_P(const char* str);
 
@@ -125,6 +130,13 @@ extern void menu_draw_float31(const char* str, float val);
 
 extern void menu_draw_float13(const char* str, float val);
 
+struct SheetFormatBuffer
+{
+    char c[19];
+};
+
+extern void menu_format_sheet_E(const Sheet &sheet_E, SheetFormatBuffer &buffer);
+
 
 #define MENU_ITEM_EDIT_int3_P(str, pval, minval, maxval) do { if (menu_item_edit_P(str, pval, minval, maxval)) return; } while (0)
 //#define MENU_ITEM_EDIT_int3_P(str, pval, minval, maxval) MENU_ITEM_EDIT(int3, str, pval, minval, maxval)

Firmware/mesh_bed_calibration.cpp

@@ -3031,7 +3031,8 @@ void babystep_load()
         check_babystep(); //checking if babystep is in allowed range, otherwise setting babystep to 0
         
         // End of G80: Apply the baby stepping value.
-        EEPROM_read_B(EEPROM_BABYSTEP_Z, &babystepLoadZ);
+        babystepLoadZ = eeprom_read_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->
+                    s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))].z_offset)));
                             
     #if 0
         SERIAL_ECHO("Z baby step: ");
@@ -3186,4 +3187,4 @@ void mbl_interpolation(uint8_t meas_points) {
 			}
 		}
 	}
-}
+}

Firmware/messages.c

@@ -10,7 +10,7 @@
 //internationalized messages
 const char MSG_AUTO_HOME[] PROGMEM_I1 = ISTR("Auto home"); ////
 const char MSG_AUTO_MODE_ON[] PROGMEM_I1 = ISTR("Mode [auto power]"); ////
-const char MSG_BABYSTEP_Z[] PROGMEM_I1 = ISTR("Live adjust Z"); ////
+const char MSG_BABYSTEP_Z[] PROGMEM_I1 = ISTR("Live adjust Z"); //// c=18
 const char MSG_BABYSTEP_Z_NOT_SET[] PROGMEM_I1 = ISTR("Distance between tip of the nozzle and the bed surface has not been set yet. Please follow the manual, chapter First steps, section First layer calibration."); ////c=20 r=12
 const char MSG_BED[] PROGMEM_I1 = ISTR("Bed"); ////
 const char MSG_BED_DONE[] PROGMEM_I1 = ISTR("Bed done"); ////
@@ -55,6 +55,7 @@ const char MSG_CUT_FILAMENT[] PROGMEM_I1 = ISTR("Cut filament"); //// Number 1 t
 const char MSG_M117_V2_CALIBRATION[] PROGMEM_I1 = ISTR("M117 First layer cal."); ////c=25 r=1
 const char MSG_MAIN[] PROGMEM_I1 = ISTR("Main"); ////
 const char MSG_BACK[] PROGMEM_I1 = ISTR("Back"); ////
+const char MSG_SHEET[] PROGMEM_I1 = ISTR("Sheet"); ////c=10
 const char MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1[] PROGMEM_I1 = ISTR("Measuring reference height of calibration point"); ////c=60
 const char MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2[] PROGMEM_I1 = ISTR(" of 9"); ////c=14
 const char MSG_MENU_CALIBRATION[] PROGMEM_I1 = ISTR("Calibration"); ////
@@ -126,3 +127,6 @@ const char MSG_ENDSTOP_OPEN[] PROGMEM_N1 = "open"; ////
 const char MSG_POWERUP[] PROGMEM_N1 = "PowerUp"; ////
 const char MSG_ERR_STOPPED[] PROGMEM_N1 = "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"; ////
 const char MSG_ENDSTOP_HIT[] PROGMEM_N1 = "TRIGGERED"; ////
+const char MSG_V2_CALIBRATION[] PROGMEM_N1 = "First layer cal."; ////c=17 r=1
+const char MSG_SELECT[] PROGMEM_N1 = "Select"; ////
+const char MSG_RENAME[] PROGMEM_N1 = "Rename"; ////

Firmware/messages.h

@@ -54,6 +54,7 @@ extern const char MSG_LOADING_FILAMENT[];
 extern const char MSG_M117_V2_CALIBRATION[];
 extern const char MSG_MAIN[];
 extern const char MSG_BACK[];
+extern const char MSG_SHEET[];
 extern const char MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1[];
 extern const char MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2[];
 extern const char MSG_MENU_CALIBRATION[];
@@ -127,6 +128,9 @@ extern const char MSG_ERR_STOPPED[];
 extern const char MSG_ENDSTOP_HIT[];
 extern const char MSG_EJECT_FILAMENT[];
 extern const char MSG_CUT_FILAMENT[];
+extern const char MSG_V2_CALIBRATION[];
+extern const char MSG_SELECT[];
+extern const char MSG_RENAME[];
 
 #if defined(__cplusplus)
 }

Firmware/mmu.cpp

@@ -81,9 +81,11 @@ uint16_t mmu_power_failures = 0;
 
 
 #ifdef MMU_DEBUG
+static const auto DEBUG_PUTCHAR = putchar;
 static const auto DEBUG_PUTS_P = puts_P;
 static const auto DEBUG_PRINTF_P = printf_P;
 #else //MMU_DEBUG
+#define DEBUG_PUTCHAR(c)
 #define DEBUG_PUTS_P(str)
 #define DEBUG_PRINTF_P( __fmt, ... )
 #endif //MMU_DEBUG
@@ -1447,26 +1449,69 @@ bFilamentAction=false;                            // NOT in "mmu_fil_eject_menu(
 	}
 }
 
+//! @brief Fits filament tip into heatbreak?
+//!
+//! If PTFE tube is jammed, this causes filament to be unloaded and no longer
+//! being detected by the pulley IR sensor.
+//! @retval true Fits
+//! @retval false Doesn't fit
+static bool can_load()
+{
+    current_position[E_AXIS] += 60;
+    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
+            current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+    current_position[E_AXIS] -= 52;
+    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
+            current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+    st_synchronize();
+
+    uint_least8_t filament_detected_count = 0;
+    const float e_increment = 0.2;
+    const uint_least8_t steps = 6.0 / e_increment;
+    DEBUG_PUTS_P(PSTR("MMU can_load:"));
+    for(uint_least8_t i = 0; i < steps; ++i)
+    {
+        current_position[E_AXIS] -= e_increment;
+        plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
+                current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+        st_synchronize();
+        if(0 == PIN_GET(IR_SENSOR_PIN))
+        {
+            ++filament_detected_count;
+            DEBUG_PUTCHAR('O');
+        }
+        else
+        {
+            DEBUG_PUTCHAR('o');
+        }
+    }
+    if (filament_detected_count > steps - 4)
+    {
+        DEBUG_PUTS_P(PSTR(" succeeded."));
+        return true;
+    }
+    else
+    {
+        DEBUG_PUTS_P(PSTR(" failed."));
+        return false;
+    }
+}
+
 //! @brief load more
 //!
 //! Try to feed more filament from MMU if it is not detected by filament sensor.
-//! Move filament back and forth to nozzle in order to detect jam.
-//! If PTFE tube is jammed, this cause filament to be unloaded and no longer
-//! detected by pulley IR sensor in next step.
-static void load_more()
+//! @retval true Success, filament detected by IR sensor
+//! @retval false Failed, filament not detected by IR sensor after maximum number of attempts
+static bool load_more()
 {
     for (uint8_t i = 0; i < MMU_IDLER_SENSOR_ATTEMPTS_NR; i++)
     {
-        if (PIN_GET(IR_SENSOR_PIN) == 0) break;
+        if (PIN_GET(IR_SENSOR_PIN) == 0) return true;
         DEBUG_PRINTF_P(PSTR("Additional load attempt nr. %d\n"), i);
         mmu_command(MmuCmd::C0);
         manage_response(true, true, MMU_LOAD_MOVE);
     }
-    current_position[E_AXIS] += 60;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
-    current_position[E_AXIS] -= 58;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
-    st_synchronize();
+    return false;
 }
 
 static void increment_load_fail()
@@ -1507,7 +1552,8 @@ void mmu_continue_loading(bool blocking)
 	    return;
 	}
 
-    load_more();
+    bool success = load_more();
+    if (success) success = can_load();
 
     enum class Ls : uint_least8_t
     {
@@ -1517,7 +1563,10 @@ void mmu_continue_loading(bool blocking)
     };
     Ls state = Ls::Enter;
 
-    while (PIN_GET(IR_SENSOR_PIN) != 0)
+    const uint_least8_t max_retry = 2;
+    uint_least8_t retry = 0;
+
+    while (!success)
     {
         switch (state)
         {
@@ -1534,8 +1583,10 @@ void mmu_continue_loading(bool blocking)
 #endif //MMU_HAS_CUTTER
             mmu_command(MmuCmd::T0 + tmp_extruder);
             manage_response(true, true, MMU_TCODE_MOVE);
-            load_more();
-            state = Ls::Unload;
+            success = load_more();
+            if (success) success = can_load();
+            ++retry; // overflow not handled, as it is not dangerous.
+            if (retry >= max_retry) state = Ls::Unload;
             break;
         case Ls::Unload:
             stop_and_save_print_to_ram(0, 0);

Firmware/ultralcd.cpp

@@ -3068,13 +3068,13 @@ static void lcd_move_z() {
  * other value leads to storing Z_AXIS
  * @param msg text to be displayed
  */
-static void _lcd_babystep(int axis, const char *msg) 
+static void lcd_babystep_z()
 {
 	typedef struct
-	{	// 19bytes total
-		int8_t status;                 // 1byte
-		int babystepMem[3];            // 6bytes
-		float babystepMemMM[3];        // 12bytes
+	{
+		int8_t status;
+		int16_t babystepMemZ;
+		float babystepMemMMZ;
 	} _menu_data_t;
 	static_assert(sizeof(menu_data)>= sizeof(_menu_data_t),"_menu_data_t doesn't fit into menu_data");
 	_menu_data_t* _md = (_menu_data_t*)&(menu_data[0]);
@@ -3084,18 +3084,20 @@ static void _lcd_babystep(int axis, const char *msg)
 		// Initialize its status.
 		_md->status = 1;
 		check_babystep();
-
-		EEPROM_read_B(EEPROM_BABYSTEP_X, &_md->babystepMem[0]);
-		EEPROM_read_B(EEPROM_BABYSTEP_Y, &_md->babystepMem[1]);
-		EEPROM_read_B(EEPROM_BABYSTEP_Z, &_md->babystepMem[2]);
+		
+		if(!is_sheet_initialized()){
+			_md->babystepMemZ = 0;
+		}
+		else{
+			_md->babystepMemZ = eeprom_read_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->
+					s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))].z_offset)));
+		}
 
 		// same logic as in babystep_load
 	    if (calibration_status() >= CALIBRATION_STATUS_LIVE_ADJUST)
-			_md->babystepMem[2] = 0;
+			_md->babystepMemZ = 0;
 
-		_md->babystepMemMM[0] = _md->babystepMem[0]/cs.axis_steps_per_unit[X_AXIS];
-		_md->babystepMemMM[1] = _md->babystepMem[1]/cs.axis_steps_per_unit[Y_AXIS];
-		_md->babystepMemMM[2] = _md->babystepMem[2]/cs.axis_steps_per_unit[Z_AXIS];
+		_md->babystepMemMMZ = _md->babystepMemZ/cs.axis_steps_per_unit[Z_AXIS];
 		lcd_draw_update = 1;
 		//SERIAL_ECHO("Z baby step: ");
 		//SERIAL_ECHO(_md->babystepMem[2]);
@@ -3106,46 +3108,49 @@ static void _lcd_babystep(int axis, const char *msg)
 	if (lcd_encoder != 0) 
 	{
 		if (homing_flag) lcd_encoder = 0;
-		_md->babystepMem[axis] += (int)lcd_encoder;
-		if (axis == 2)
-		{
-			if (_md->babystepMem[axis] < Z_BABYSTEP_MIN) _md->babystepMem[axis] = Z_BABYSTEP_MIN; //-3999 -> -9.99 mm
-			else if (_md->babystepMem[axis] > Z_BABYSTEP_MAX) _md->babystepMem[axis] = Z_BABYSTEP_MAX; //0
-			else
-			{
-				CRITICAL_SECTION_START
-				babystepsTodo[axis] += (int)lcd_encoder;
-				CRITICAL_SECTION_END		
-			}
-		}
-		_md->babystepMemMM[axis] = _md->babystepMem[axis]/cs.axis_steps_per_unit[axis]; 
+		_md->babystepMemZ += (int)lcd_encoder;
+
+        if (_md->babystepMemZ < Z_BABYSTEP_MIN) _md->babystepMemZ = Z_BABYSTEP_MIN; //-3999 -> -9.99 mm
+        else if (_md->babystepMemZ > Z_BABYSTEP_MAX) _md->babystepMemZ = Z_BABYSTEP_MAX; //0
+        else
+        {
+            CRITICAL_SECTION_START
+            babystepsTodo[Z_AXIS] += (int)lcd_encoder;
+            CRITICAL_SECTION_END
+        }
+
+		_md->babystepMemMMZ = _md->babystepMemZ/cs.axis_steps_per_unit[Z_AXIS];
 		_delay(50);
 		lcd_encoder = 0;
 		lcd_draw_update = 1;
 	}
 	if (lcd_draw_update)
 	{
+	    SheetFormatBuffer buffer;
+	    menu_format_sheet_E(EEPROM_Sheets_base->s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))], buffer);
+	    lcd_set_cursor(0, 0);
+	    lcd_print(buffer.c);
 	    lcd_set_cursor(0, 1);
-		menu_draw_float13(msg, _md->babystepMemMM[axis]);
+		menu_draw_float13(_i("Adjusting Z:"), _md->babystepMemMMZ); ////MSG_BABYSTEPPING_Z c=15 Beware: must include the ':' as its last character
 	}
 	if (LCD_CLICKED || menu_leaving)
 	{
 		// Only update the EEPROM when leaving the menu.
-		EEPROM_save_B(
-		(axis == X_AXIS) ? EEPROM_BABYSTEP_X : ((axis == Y_AXIS) ? EEPROM_BABYSTEP_Y : EEPROM_BABYSTEP_Z),
-		&_md->babystepMem[axis]);
-		if(Z_AXIS == axis) calibration_status_store(CALIBRATION_STATUS_CALIBRATED);
+		eeprom_update_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->
+                s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))].z_offset)),
+		        _md->babystepMemZ);
+		eeprom_update_byte(&(EEPROM_Sheets_base->s[(eeprom_read_byte(
+		        &(EEPROM_Sheets_base->active_sheet)))].bed_temp),
+		        target_temperature_bed);
+		eeprom_update_byte(&(EEPROM_Sheets_base->s[(eeprom_read_byte(
+		        &(EEPROM_Sheets_base->active_sheet)))].pinda_temp),
+		        current_temperature_pinda);
+		calibration_status_store(CALIBRATION_STATUS_CALIBRATED);
 	}
 	if (LCD_CLICKED) menu_back();
 }
 
 
-static void lcd_babystep_z()
-{
-	_lcd_babystep(Z_AXIS, (_i("Adjusting Z:")));////MSG_BABYSTEPPING_Z c=15 Beware: must include the ':' as its last character
-}
-
-
 typedef struct
 {	// 12bytes + 9bytes = 21bytes total
     menu_data_edit_t reserved; //12 bytes reserved for number editing functions
@@ -6300,6 +6305,95 @@ void lcd_resume_print()
     isPrintPaused = false;
 }
 
+static void change_sheet(uint8_t sheet_num)
+{
+	eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), sheet_num);
+	if(is_sheet_initialized())
+		calibration_status_store(CALIBRATION_STATUS_CALIBRATED);
+	else
+		calibration_status_store(CALIBRATION_STATUS_LIVE_ADJUST);
+
+    menu_back(3);
+}
+
+static void lcd_select_sheet_0_menu()
+{
+	change_sheet(0);
+}
+static void lcd_select_sheet_1_menu()
+{
+	change_sheet(1);
+}
+static void lcd_select_sheet_2_menu()
+{
+	change_sheet(2);
+}
+
+static void lcd_select_sheet_menu()
+{
+    MENU_BEGIN();
+    MENU_ITEM_BACK_P(_T(MSG_BACK));
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[0], lcd_select_sheet_0_menu);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[1], lcd_select_sheet_1_menu);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[2], lcd_select_sheet_2_menu);
+    MENU_END();
+}
+
+static void lcd_rename_sheet_menu()
+{
+    struct MenuData
+    {
+        bool initialized;
+        uint8_t selected;
+        char name[sizeof(Sheet::name)];
+    };
+    static_assert(sizeof(menu_data)>= sizeof(MenuData),"MenuData doesn't fit into menu_data");
+    MenuData* menuData = (MenuData*)&(menu_data[0]);
+
+    if (!menuData->initialized)
+    {
+        eeprom_read_block(menuData->name, EEPROM_Sheets_base->s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))].name, sizeof(Sheet::name));
+        lcd_encoder = menuData->name[0];
+        menuData->initialized = true;
+    }
+    if (lcd_encoder < '\x20') lcd_encoder = '\x20';
+    if (lcd_encoder > '\x7F') lcd_encoder = '\x7F';
+
+    menuData->name[menuData->selected] = lcd_encoder;
+    lcd_set_cursor(0,0);
+    for (uint_least8_t i = 0; i < sizeof(Sheet::name); ++i)
+    {
+        lcd_putc(menuData->name[i]);
+    }
+    lcd_set_cursor(menuData->selected, 1);
+    lcd_putc('^');
+    if (lcd_clicked())
+    {
+        if ((menuData->selected + 1u) < sizeof(Sheet::name))
+        {
+            lcd_encoder = menuData->name[++(menuData->selected)];
+        }
+        else
+        {
+            eeprom_update_block(menuData->name,
+                EEPROM_Sheets_base->s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))].name,
+                sizeof(Sheet::name));
+            menu_back();
+        }
+    }
+}
+
+static void lcd_sheet_menu()
+{
+    MENU_BEGIN();
+    MENU_ITEM_BACK_P(_T(MSG_MAIN));
+    MENU_ITEM_SUBMENU_P(_T(MSG_SELECT), lcd_select_sheet_menu); //// c=18
+    MENU_ITEM_SUBMENU_P(_T(MSG_RENAME), lcd_rename_sheet_menu); //// c=18
+    MENU_ITEM_SUBMENU_P(_T(MSG_V2_CALIBRATION), lcd_v2_calibration); ////MSG_V2_CALIBRATION c=17 r=1
+
+    MENU_END();
+}
+
 static void lcd_main_menu()
 {
 
@@ -6321,55 +6415,6 @@ static void lcd_main_menu()
  MENU_ITEM_FUNCTION_P(PSTR("recover print"), recover_print);
  MENU_ITEM_FUNCTION_P(PSTR("power panic"), uvlo_);
 #endif //TMC2130_DEBUG
-
- /* if (farm_mode && !IS_SD_PRINTING )
-    {
-    
-        int tempScrool = 0;
-        if (lcd_draw_update == 0 && LCD_CLICKED == 0)
-            //_delay(100);
-            return; // nothing to do (so don't thrash the SD card)
-        uint16_t fileCnt = card.getnrfilenames();
-        
-        card.getWorkDirName();
-        if (card.filename[0] == '/')
-        {
-#if SDCARDDETECT == -1
-            MENU_ITEM_FUNCTION_P(_T(MSG_REFRESH), lcd_sd_refresh);
-#endif
-        } else {
-            MENU_ITEM_FUNCTION_P(PSTR(LCD_STR_FOLDER ".."), lcd_sd_updir);
-        }
-        
-        for (uint16_t i = 0; i < fileCnt; i++)
-        {
-            if (menu_item == menu_line)
-            {
-#ifndef SDCARD_RATHERRECENTFIRST
-                card.getfilename(i);
-#else
-                card.getfilename(fileCnt - 1 - i);
-#endif
-                if (card.filenameIsDir)
-                {
-                    MENU_ITEM_SDDIR(_T(MSG_CARD_MENU), card.filename, card.longFilename);
-                } else {
-                    
-                    MENU_ITEM_SDFILE(_T(MSG_CARD_MENU), card.filename, card.longFilename);
-                    
-                    
-                    
-                    
-                }
-            } else {
-                MENU_ITEM_DUMMY();
-            }
-        }
-        
-        MENU_ITEM_BACK_P(PSTR("- - - - - - - - -"));
-    
-        
-    }*/
  
   if ( ( IS_SD_PRINTING || is_usb_printing || (lcd_commands_type == LcdCommands::Layer1Cal)) && (current_position[Z_AXIS] < Z_HEIGHT_HIDE_LIVE_ADJUST_MENU) && !homing_flag && !mesh_bed_leveling_flag)
   {
@@ -6385,6 +6430,8 @@ static void lcd_main_menu()
     MENU_ITEM_SUBMENU_P(_i("Preheat"), lcd_preheat_menu);////MSG_PREHEAT
   }
 
+
+
 #ifdef SDSUPPORT
   if (card.cardOK || lcd_commands_type == LcdCommands::Layer1Cal)
   {
@@ -6475,6 +6522,8 @@ static void lcd_main_menu()
 
   }
 
+  if(!isPrintPaused)MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))], lcd_sheet_menu);
+  
   if (!is_usb_printing && (lcd_commands_type != LcdCommands::Layer1Cal))
   {
 	  MENU_ITEM_SUBMENU_P(_i("Statistics  "), lcd_menu_statistics);////MSG_STATISTICS

PF-build.sh

@@ -426,14 +426,14 @@ do
 		sleep 2
 		#$BUILDER -dump-prefs -logger=machine -hardware $ARDUINO/hardware -hardware $ARDUINO/portable/packages -tools $ARDUINO/tools-builder -tools $ARDUINO/hardware/tools/avr -tools $ARDUINO/portable/packages -built-in-libraries $ARDUINO/libraries -libraries $ARDUINO/portable/sketchbook/libraries -fqbn=rambo:avr:rambo -ide-version=10805 -build-path=$BUILD_PATH -warnings=none -quiet $SCRIPT_PATH/Firmware/Firmware.ino || exit 12
 		#$BUILDER -compile -logger=machine -hardware $ARDUINO/hardware -hardware $ARDUINO/portable/packages -tools $ARDUINO/tools-builder -tools $ARDUINO/hardware/tools/avr -tools $ARDUINO/portable/packages -built-in-libraries $ARDUINO/libraries -libraries $ARDUINO/portable/sketchbook/libraries -fqbn=rambo:avr:rambo -ide-version=10805 -build-path=$BUILD_PATH -warnings=none -quiet $SCRIPT_PATH/Firmware/Firmware.ino || exit 13
-		$BUILDER -compile -hardware $ARDUINO/hardware -hardware $ARDUINO/portable/packages -tools $ARDUINO/tools-builder -tools $ARDUINO/hardware/tools/avr -tools $ARDUINO/portable/packages -built-in-libraries $ARDUINO/libraries -libraries $ARDUINO/portable/sketchbook/libraries -fqbn=rambo:avr:rambo -ide-version=10805 -build-path=$BUILD_PATH -warnings=default $SCRIPT_PATH/Firmware/Firmware.ino || exit 14
+		$BUILDER -compile -hardware $ARDUINO/hardware -hardware $ARDUINO/portable/packages -tools $ARDUINO/tools-builder -tools $ARDUINO/hardware/tools/avr -tools $ARDUINO/portable/packages -built-in-libraries $ARDUINO/libraries -libraries $ARDUINO/portable/sketchbook/libraries -fqbn=rambo:avr:rambo -ide-version=10805 -build-path=$BUILD_PATH -warnings=all $SCRIPT_PATH/Firmware/Firmware.ino || exit 14
 		echo "$(tput sgr 0)"
 	fi
 	if [ $OSTYPE == "linux-gnu" ] ; then
 		echo "Start to build Prusa Firmware under Linux 64..."
 		echo "Using variant $VARIANT$(tput setaf 3)"
 		sleep 2
-		$BUILD_ENV_PATH/arduino $SCRIPT_PATH/Firmware/Firmware.ino --verify --board rambo:avr:rambo --pref build.path=$BUILD_PATH || exit 14
+		$BUILD_ENV_PATH/arduino $SCRIPT_PATH/Firmware/Firmware.ino --verify --board rambo:avr:rambo --pref build.path=$BUILD_PATH --pref compiler.warning_level=all || exit 14
 		echo "$(tput sgr 0)"
 	fi
 

README.md

@@ -14,8 +14,8 @@
 
 # Build
 ## Linux
-Run shell script build.sh to build for MK3 and flash with Sli3er.  
-If you have different printel model, follow step [2.b](#2b) from Windows build first.  
+Run shell script build.sh to build for MK3 and flash with Slic3er.  
+If you have a different printer model, follow step [2.b](#2b) from Windows build first.  
 If you wish to flash from Arduino, follow step [2.c](#2c) from Windows build first.  
 
 The script downloads Arduino with our modifications and Rambo board support installed, unpacks it into folder PF-build-env-\<version\> on the same level, as your Prusa-Firmware folder is located, builds firmware for MK3 using that Arduino in Prusa-Firmware-build folder on the same level as Prusa-Firmware, runs secondary language support scripts. Firmware with secondary language support is generated in lang subfolder. Use firmware.hex for MK3 variant. Use firmware_\<lang\>.hex for other printers. Don't forget to follow step [2.b](#2b) first for non-MK3 printers.
@@ -40,11 +40,11 @@ type location
 or you can 'manually' modify the item  
 `"boardsmanager.additional.urls=....."`  
 at the file `"preferences.txt"` (this parameter allows you to write a comma-separated list of addresses)  
-_note: you can find location of this file on your disk by following way:  
+_note: you can find location of this file on your disk by doing the following:  
 `File->Preferences->Settings`  (`"More preferences can be edited in file ..."`)_  
-than do it  
+then choose 
 `Tools->Board->BoardsManager`  
-from viewed list select an item `"RAMBo"` (will probably be labeled as `"RepRap Arduino-compatible Mother Board (RAMBo) by UltiMachine"`  
+from viewed list and select the item labeled `"RAMBo"` (will probably be labeled as `"RepRap Arduino-compatible Mother Board (RAMBo) by UltiMachine"`  
 _note: select this item for any variant of board used in printers `'Prusa i3 MKx'`, that is for `RAMBo-mini x.y` and `EINSy x.y` to_  
 'clicking' the item will display the installation button; select choice `"1.0.1"` from the list(last known version as of the date of issue of this document)  
 _(after installation, the item is labeled as `"INSTALLED"` and can then be used for target board selection)_  
@@ -66,7 +66,7 @@ b.<a name="2b"></a> In the subdirectory `"Firmware/variants/"` select the config
 
 c.<a name="2c"></a> In file `"Firmware/config.h"` set LANG_MODE to 0.
 
-run `"Arduino IDE"`; select the file `"Firmware.ino"` from the subdirectory `"Firmware/"` at the location, where you placed the source codes  
+run `"Arduino IDE"`; select the file `"Firmware.ino"` from the subdirectory `"Firmware/"` at the location, where you placed the source code  
 `File->Open`  
 make the desired code customizations; **all changes are on your own risk!**  
 
@@ -146,7 +146,7 @@ cmake
 build system - ninja or gnu make
 
 ## Building
-Create folder where you want to build tests.
+Create a folder where you want to build tests.
 
 Example:
 

lang/lang-build.sh

@@ -82,7 +82,7 @@ generate_binary()
  rm -f lang_$1.dat
  LNG=$1
  #check lang dictionary
- /usr/bin/env python lang-check.py $1
+ /usr/bin/env python lang-check.py $1 --no-warning
  #create lang_xx.tmp - different processing for 'en' language
  if [ "$1" = "en" ]; then
   #remove comments and empty lines