MK1 backport - rename configuration files + version for RAMBo10a

Firmware/variants/1_75mm_MK1-RAMBo10a-E3Dv6full.h

@@ -0,0 +1,404 @@
+#ifndef CONFIGURATION_PRUSA_H
+#define CONFIGURATION_PRUSA_H
+
+/*------------------------------------
+GENERAL SETTINGS
+*------------------------------------*/
+
+// Printer revision
+#define FILAMENT_SIZE "1_75mm_MK1"
+#define NOZZLE_TYPE "E3Dv6full"
+
+// Developer flag
+#define DEVELOPER
+
+// Printer name
+#define CUSTOM_MENDEL_NAME "Prusa i3 MK1"
+
+// Electronics
+#define MOTHERBOARD BOARD_RAMBO_MINI_1_0
+
+// MK1 back port
+#define MK1BP
+
+// Prusa Single extruder multiple material suport
+//#define SNMM
+
+// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
+//#define E3D_PT100_EXTRUDER_WITH_AMP
+//#define E3D_PT100_EXTRUDER_NO_AMP
+//#define E3D_PT100_BED_WITH_AMP
+//#define E3D_PT100_BED_NO_AMP
+
+
+/*------------------------------------
+AXIS SETTINGS
+*------------------------------------*/
+
+// Steps per unit {X,Y,Z,E}
+#ifdef SNMM
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/0.8,140}
+#else
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/0.8,174.2}
+#endif
+
+
+// Endstop inverting
+const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+
+// Home position
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS 0
+#define MANUAL_Z_HOME_POS 0.25
+
+// Travel limits after homing
+#define X_MAX_POS 214
+#define X_MIN_POS 0
+#define Y_MAX_POS 198
+#define Y_MIN_POS 0
+#define Z_MAX_POS 201
+#define Z_MIN_POS 0.23
+
+// Canceled home position
+#define X_CANCEL_POS 50
+#define Y_CANCEL_POS 190
+
+//Pause print position
+#define X_PAUSE_POS 50
+#define Y_PAUSE_POS 190
+#define Z_PAUSE_LIFT 20
+
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+#define HOMING_FEEDRATE {3000, 3000, 240, 0}  // set the homing speeds (mm/min)
+
+#define DEFAULT_MAX_FEEDRATE          {500, 500, 3, 25}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {9000,9000,30,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  3000   // X, Y, Z and E max acceleration in mm/s^2 for retracts
+
+
+#define MANUAL_FEEDRATE {3000, 3000, 240, 60}   // set the speeds for manual moves (mm/min)
+
+#define Z_AXIS_ALWAYS_ON 1
+
+/*------------------------------------
+EXTRUDER SETTINGS
+*------------------------------------*/
+
+// Mintemps
+#define HEATER_0_MINTEMP 15
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define BED_MINTEMP 15
+
+// Maxtemps
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define HEATER_0_MAXTEMP 410
+#else
+#define HEATER_0_MAXTEMP 305
+#endif
+#define HEATER_1_MAXTEMP 305
+#define HEATER_2_MAXTEMP 305
+#define BED_MAXTEMP 150
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_Kp 21.70
+#define  DEFAULT_Ki 1.60
+#define  DEFAULT_Kd 73.76
+#else
+// Define PID constants for extruder
+#define  DEFAULT_Kp 40.925
+#define  DEFAULT_Ki 4.875
+#define  DEFAULT_Kd 86.085
+#endif
+
+// Extrude mintemp
+#define EXTRUDE_MINTEMP 190
+
+// Extruder cooling fans
+#define EXTRUDER_0_AUTO_FAN_PIN   8
+#define EXTRUDER_1_AUTO_FAN_PIN   -1
+#define EXTRUDER_2_AUTO_FAN_PIN   -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
+
+
+
+
+
+
+#ifdef SNMM
+//#define BOWDEN_LENGTH	408
+#define BOWDEN_LENGTH 433 //default total length for filament fast loading part; max length for extrusion is 465 mm!; this length can be adjusted in service menu
+#define FIL_LOAD_LENGTH 102 //length for loading filament into the nozzle
+#define FIL_COOLING 10 //length for cooling moves
+#define E_MOTOR_LOW_CURRENT 350 // current for PRUSAY code
+#define E_MOTOR_HIGH_CURRENT 700 //current for unloading filament, stop print, PRUSAY ramming
+#endif //SNMM
+
+//#define DIS //for measuring bed heigth and PINDa detection heigth relative to auto home point, experimental function
+
+
+/*------------------------------------
+CHANGE FILAMENT SETTINGS
+*------------------------------------*/
+
+// Filament change configuration
+#define FILAMENTCHANGEENABLE
+#ifdef FILAMENTCHANGEENABLE
+#define FILAMENTCHANGE_XPOS 211
+#define FILAMENTCHANGE_YPOS 0
+#define FILAMENTCHANGE_ZADD 2
+#define FILAMENTCHANGE_FIRSTRETRACT -2
+#define FILAMENTCHANGE_FINALRETRACT -80
+
+#define FILAMENTCHANGE_FIRSTFEED 70
+#define FILAMENTCHANGE_FINALFEED 50
+#define FILAMENTCHANGE_RECFEED 5
+
+#define FILAMENTCHANGE_XYFEED 50
+#define FILAMENTCHANGE_EFEED 20
+#define FILAMENTCHANGE_RFEED 400
+#define FILAMENTCHANGE_EXFEED 2
+#define FILAMENTCHANGE_ZFEED 15
+
+#endif
+
+/*------------------------------------
+ADDITIONAL FEATURES SETTINGS
+*------------------------------------*/
+
+// Define Prusa filament runout sensor
+//#define FILAMENT_RUNOUT_SUPPORT
+
+#ifdef FILAMENT_RUNOUT_SUPPORT
+#define FILAMENT_RUNOUT_SENSOR 1
+#endif
+
+// temperature runaway
+#define TEMP_RUNAWAY_BED_HYSTERESIS 5
+#define TEMP_RUNAWAY_BED_TIMEOUT 360
+
+#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
+#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
+
+/*------------------------------------
+MOTOR CURRENT SETTINGS
+*------------------------------------*/
+
+// Motor Current setting for BIG RAMBo
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135}
+
+// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range
+#if MOTHERBOARD == 102 || MOTHERBOARD == 302
+#define MOTOR_CURRENT_PWM_RANGE 2000
+#define DEFAULT_PWM_MOTOR_CURRENT  {270, 830, 450} // {XY,Z,E}
+#define DEFAULT_PWM_MOTOR_CURRENT_LOUD  {540, 830, 500} // {XY,Z,E}
+#endif
+
+/*------------------------------------
+BED SETTINGS
+*------------------------------------*/
+
+// Define Mesh Bed Leveling system to enable it
+#define MESH_BED_LEVELING
+#ifdef MESH_BED_LEVELING
+
+#define MBL_Z_STEP 0.01
+
+// Mesh definitions
+#define MESH_MIN_X 35
+#define MESH_MAX_X 238
+#define MESH_MIN_Y 6
+#define MESH_MAX_Y 202
+
+// Mesh upsample definition
+#define MESH_NUM_X_POINTS 7
+#define MESH_NUM_Y_POINTS 7
+// Mesh measure definition
+#define MESH_MEAS_NUM_X_POINTS 3
+#define MESH_MEAS_NUM_Y_POINTS 3
+
+#define MESH_HOME_Z_CALIB 0.2
+#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+
+#define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 9     // Z probe to nozzle Y offset: -front +behind
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4  // Z probe to nozzle Z offset: -below (always!)
+#endif
+
+// Bed Temperature Control
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+// Bed temperature compensation settings
+#define BED_OFFSET 10
+#define BED_OFFSET_START 40
+#define BED_OFFSET_CENTER 50
+
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_bedKp 21.70
+#define  DEFAULT_bedKi 1.60
+#define  DEFAULT_bedKd 73.76
+#else
+#define  DEFAULT_bedKp 126.13
+#define  DEFAULT_bedKi 4.30
+#define  DEFAULT_bedKd 924.76
+#endif
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+//    #define  DEFAULT_bedKp 97.1
+//    #define  DEFAULT_bedKi 1.41
+//    #define  DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+/*-----------------------------------
+PREHEAT SETTINGS
+*------------------------------------*/
+
+#define PLA_PREHEAT_HOTEND_TEMP 215
+#define PLA_PREHEAT_HPB_TEMP 55
+#define PLA_PREHEAT_FAN_SPEED 0  
+
+#define ABS_PREHEAT_HOTEND_TEMP 255
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 0 
+
+#define HIPS_PREHEAT_HOTEND_TEMP 220
+#define HIPS_PREHEAT_HPB_TEMP 100
+#define HIPS_PREHEAT_FAN_SPEED 0 
+
+#define PP_PREHEAT_HOTEND_TEMP 254
+#define PP_PREHEAT_HPB_TEMP 100
+#define PP_PREHEAT_FAN_SPEED 0 
+
+#define PET_PREHEAT_HOTEND_TEMP 240
+#define PET_PREHEAT_HPB_TEMP 90
+#define PET_PREHEAT_FAN_SPEED 0 
+
+#define FLEX_PREHEAT_HOTEND_TEMP 230
+#define FLEX_PREHEAT_HPB_TEMP 50
+#define FLEX_PREHEAT_FAN_SPEED 0 
+
+/*------------------------------------
+THERMISTORS SETTINGS
+*------------------------------------*/
+
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" 
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.0a
+// 247 is Pt100 with 4k7 pullup and PT100 Amplifier
+// 110 is Pt100 with 1k pullup (non standard)
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP)
+#define TEMP_SENSOR_0 247
+#elif defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define TEMP_SENSOR_0 148
+#else
+#define TEMP_SENSOR_0 5
+#endif
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#if defined(E3D_PT100_BED_WITH_AMP)
+#define TEMP_SENSOR_BED 247
+#elif defined(E3D_PT100_BED_NO_AMP)
+#define TEMP_SENSOR_BED 148
+#else
+#define TEMP_SENSOR_BED 1
+#endif
+
+#define STACK_GUARD_TEST_VALUE 0xA2A2
+
+#define MAX_BED_TEMP_CALIBRATION 50
+#define MAX_HOTEND_TEMP_CALIBRATION 50
+
+#define MAX_E_STEPS_PER_UNIT 250
+#define MIN_E_STEPS_PER_UNIT 100
+
+#define Z_BABYSTEP_MIN -3999
+#define Z_BABYSTEP_MAX 0
+
+#define PINDA_PREHEAT_X 70
+#define PINDA_PREHEAT_Y -3
+#define PINDA_PREHEAT_Z 1
+#define PINDA_HEAT_T 120 //time in s
+
+#define PINDA_MIN_T 50
+#define PINDA_STEP_T 10
+#define PINDA_MAX_T 100
+
+#define PING_TIME 60 //time in s
+#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes
+#define PING_ALLERT_PERIOD 60 //time in s
+
+#define LONG_PRESS_TIME 1000 //time in ms for button long press 
+#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
+
+#define PAUSE_RETRACT 1 
+
+#define DEFAULT_PID_TEMP 210
+
+#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration
+
+#endif //__CONFIGURATION_PRUSA_H

Firmware/variants/1_75mm-RAMBo13a-E3Dv6full.h

@@ -6,7 +6,7 @@ GENERAL SETTINGS
 *------------------------------------*/
 
 // Printer revision
-#define FILAMENT_SIZE "1_75mm_MK2"
+#define FILAMENT_SIZE "1_75mm_MK1"
 #define NOZZLE_TYPE "E3Dv6full"
 
 // Developer flag