Rambo 1.0 support (MK25, MK2)

Firmware/pins_Rambo_1_0.h

@@ -0,0 +1,139 @@
+/*****************************************************************
+* Rambo mini 1.0 Pin Assignments
+******************************************************************/
+
+#define ELECTRONICS "RAMBo10a"
+
+#define KNOWN_BOARD
+#ifndef __AVR_ATmega2560__
+  #error Oops!  Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu.
+#endif
+
+#define PINDA_THERMISTOR
+
+#define SWI2C                    // enable software i2c
+#define SWI2C_A8                 // 8bit address functions
+
+#define PAT9125_SWI2C
+#define PAT9125_SWI2C_SDA      20 //SDA on P3
+#define PAT9125_SWI2C_SCL      21 //SCL on P3
+#define PAT9125_SWI2C_CFG    0xb1 //2us clock delay, 2048 cycles timeout
+
+//#define PAT9125_HWI2C
+
+#define X_STEP_PIN             37
+#define X_DIR_PIN              48
+#define X_MIN_PIN              12
+#define X_MAX_PIN              -1
+#define X_ENABLE_PIN           29
+#define X_MS1_PIN              40
+#define X_MS2_PIN              41
+
+#define Y_STEP_PIN             36
+#define Y_DIR_PIN              49
+#define Y_MIN_PIN              11
+#define Y_MAX_PIN              -1
+#define Y_ENABLE_PIN           28
+#define Y_MS1_PIN              69
+#define Y_MS2_PIN              39
+
+#define Z_STEP_PIN             35
+#define Z_DIR_PIN              47
+#define Z_MIN_PIN              10
+#define Z_MAX_PIN              23
+#define Z_ENABLE_PIN           27
+#define Z_MS1_PIN              68
+#define Z_MS2_PIN              67
+
+#define HEATER_BED_PIN          4 //PG5
+#define TEMP_BED_PIN            2 //A2
+
+#define HEATER_0_PIN            3 //PE5
+#define TEMP_0_PIN              0 //A0
+
+#define HEATER_1_PIN           -1
+#define TEMP_1_PIN             -1 //A1
+
+#define HEATER_2_PIN           -1
+#define TEMP_2_PIN             -1
+
+#define TEMP_AMBIENT_PIN        6 //A6
+
+#define TEMP_PINDA_PIN          1 //A1
+
+
+
+#define E0_STEP_PIN            34
+#define E0_DIR_PIN             43
+#define E0_ENABLE_PIN          26
+#define E0_MS1_PIN             65
+#define E0_MS2_PIN             66
+
+#ifdef SNMM 
+  #define E_MUX0_PIN 17
+  #define E_MUX1_PIN 16
+#endif
+
+
+#define MOTOR_CURRENT_PWM_XY_PIN 46
+#define MOTOR_CURRENT_PWM_Z_PIN  45
+#define MOTOR_CURRENT_PWM_E_PIN  44
+#define SDPOWER             -1
+#define SDSS                53
+#define LED_PIN             13
+#define FAN_PIN              6
+#define FAN_1_PIN           -1
+#define PS_ON_PIN           -1
+#define KILL_PIN            -1  // 80 with Smart Controller LCD
+#define SUICIDE_PIN         -1  // PIN that has to be turned on right after start, to keep power flowing.
+#define TACH_0				30	// noctua extruder fan
+
+#ifdef ULTRA_LCD
+
+//#define KILL_PIN            32
+
+#ifdef NEWPANEL
+
+#define BEEPER              78  // Beeper on AUX-4
+#define LCD_PINS_RS         38
+#define LCD_PINS_ENABLE      5
+#define LCD_PINS_D4	        14
+#define LCD_PINS_D5         15
+#define LCD_PINS_D6         32
+#define LCD_PINS_D7         31
+
+//buttons are directly attached using AUX-2
+#define BTN_EN1                80
+#define BTN_EN2                73
+#define BTN_ENC                21  // the click
+
+#define SDCARDDETECT           72
+
+
+#endif //NEWPANEL
+#endif //ULTRA_LCD
+
+// Support for an 8 bit logic analyzer, for example the Saleae.
+// Channels 0-2 are fast, they could generate 2.667Mhz waveform with a software loop.
+#define LOGIC_ANALYZER_CH0		X_MIN_PIN		// PB6
+#define LOGIC_ANALYZER_CH1		Y_MIN_PIN		// PB5
+#define LOGIC_ANALYZER_CH2		53				// PB0 (PROC_nCS)
+// Channels 3-7 are slow, they could generate
+// 0.889Mhz waveform with a software loop and interrupt locking,
+// 1.333MHz waveform without interrupt locking.
+#define LOGIC_ANALYZER_CH3 		73				// PJ3
+// PK0 has no Arduino digital pin assigned, so we set it directly.
+#define WRITE_LOGIC_ANALYZER_CH4(value) if (value) PORTK |= (1 << 0); else PORTK &= ~(1 << 0) // PK0
+#define LOGIC_ANALYZER_CH5		16				// PH0 (RXD2)
+#define LOGIC_ANALYZER_CH6		17				// PH1 (TXD2)
+#define LOGIC_ANALYZER_CH7 		76				// PJ5
+
+#define LOGIC_ANALYZER_CH0_ENABLE SET_OUTPUT(LOGIC_ANALYZER_CH0)
+#define LOGIC_ANALYZER_CH1_ENABLE SET_OUTPUT(LOGIC_ANALYZER_CH1)
+#define LOGIC_ANALYZER_CH2_ENABLE SET_OUTPUT(LOGIC_ANALYZER_CH2)
+#define LOGIC_ANALYZER_CH3_ENABLE SET_OUTPUT(LOGIC_ANALYZER_CH3)
+#define LOGIC_ANALYZER_CH4_ENABLE do { DDRK |= 1 << 0; } while (0)
+#define LOGIC_ANALYZER_CH5_ENABLE do { cbi(UCSR2B, TXEN2); cbi(UCSR2B, RXEN2); cbi(UCSR2B, RXCIE2); SET_OUTPUT(LOGIC_ANALYZER_CH5); } while (0)
+#define LOGIC_ANALYZER_CH6_ENABLE do { cbi(UCSR2B, TXEN2); cbi(UCSR2B, RXEN2); cbi(UCSR2B, RXCIE2); SET_OUTPUT(LOGIC_ANALYZER_CH6); } while (0)
+#define LOGIC_ANALYZER_CH7_ENABLE SET_OUTPUT(LOGIC_ANALYZER_CH7)
+

Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h

@@ -0,0 +1,431 @@
+#ifndef CONFIGURATION_PRUSA_H
+#define CONFIGURATION_PRUSA_H
+
+/*------------------------------------
+GENERAL SETTINGS
+*------------------------------------*/
+
+// Printer revision
+#define PRINTER_TYPE PRINTER_MK2
+#define FILAMENT_SIZE "1_75mm_MK2"
+#define NOZZLE_TYPE "E3Dv6full"
+
+// Developer flag
+#define DEVELOPER
+
+// Printer name
+#define CUSTOM_MENDEL_NAME "Prusa i3 MK2"
+
+// Electronics
+#define MOTHERBOARD BOARD_RAMBO_MINI_1_0
+
+// Prusa Single extruder multiple material suport
+//#define SNMM
+
+// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
+//#define E3D_PT100_EXTRUDER_WITH_AMP
+//#define E3D_PT100_EXTRUDER_NO_AMP
+//#define E3D_PT100_BED_WITH_AMP
+//#define E3D_PT100_BED_NO_AMP
+
+
+/*------------------------------------
+AXIS SETTINGS
+*------------------------------------*/
+
+// Steps per unit {X,Y,Z,E}
+#ifdef SNMM
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,140}
+#else
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,161.3}
+#endif
+
+
+// Endstop inverting
+const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+
+// Direction inverting
+#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_Z_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_E0_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+
+
+// Home position
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS -2.2
+#define MANUAL_Z_HOME_POS 0.15
+
+// Travel limits after homing
+#define X_MAX_POS 250
+#define X_MIN_POS 0
+#define Y_MAX_POS 210
+#define Y_MIN_POS -2.2
+#define Z_MAX_POS 210
+#define Z_MIN_POS 0.15
+
+// Canceled home position
+#define X_CANCEL_POS 50
+#define Y_CANCEL_POS 190
+
+//Pause print position
+#define X_PAUSE_POS 50
+#define Y_PAUSE_POS 190
+#define Z_PAUSE_LIFT 20
+
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+#define HOMING_FEEDRATE {3000, 3000, 800, 0}  // set the homing speeds (mm/min)
+
+#define DEFAULT_MAX_FEEDRATE          {500, 500, 12, 120}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {9000,9000,500,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          1500    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1500   // X, Y, Z and E max acceleration in mm/s^2 for retracts
+
+
+#define MANUAL_FEEDRATE {3000, 3000, 1000, 100}   // set the speeds for manual moves (mm/min)
+
+#define Z_AXIS_ALWAYS_ON 1
+
+// New XYZ calibration
+//#define NEW_XYZCAL
+
+
+/*------------------------------------
+EXTRUDER SETTINGS
+*------------------------------------*/
+
+// Mintemps
+#define HEATER_0_MINTEMP 15
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define BED_MINTEMP 15
+
+// Maxtemps
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define HEATER_0_MAXTEMP 410
+#else
+#define HEATER_0_MAXTEMP 305
+#endif
+#define HEATER_1_MAXTEMP 305
+#define HEATER_2_MAXTEMP 305
+#define BED_MAXTEMP 150
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_Kp 21.70
+#define  DEFAULT_Ki 1.60
+#define  DEFAULT_Kd 73.76
+#else
+// Define PID constants for extruder
+#define  DEFAULT_Kp 40.925
+#define  DEFAULT_Ki 4.875
+#define  DEFAULT_Kd 86.085
+#endif
+
+// Extrude mintemp
+#define EXTRUDE_MINTEMP 130
+
+// Extruder cooling fans
+#define EXTRUDER_0_AUTO_FAN_PIN   8
+#define EXTRUDER_1_AUTO_FAN_PIN   -1
+#define EXTRUDER_2_AUTO_FAN_PIN   -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
+
+
+#ifdef SNMM
+//#define BOWDEN_LENGTH	408
+#define BOWDEN_LENGTH 433 //default total length for filament fast loading part; max length for extrusion is 465 mm!; this length can be adjusted in service menu
+#define FIL_LOAD_LENGTH 102 //length for loading filament into the nozzle
+#define FIL_COOLING 10 //length for cooling moves
+#define E_MOTOR_LOW_CURRENT 350 // current for PRUSAY code
+#define E_MOTOR_HIGH_CURRENT 700 //current for unloading filament, stop print, PRUSAY ramming
+#endif //SNMM
+
+//#define DIS //for measuring bed heigth and PINDa detection heigth relative to auto home point, experimental function
+
+
+/*------------------------------------
+CHANGE FILAMENT SETTINGS
+*------------------------------------*/
+
+// Filament change configuration
+#define FILAMENTCHANGEENABLE
+#ifdef FILAMENTCHANGEENABLE
+#define FILAMENTCHANGE_XPOS 211
+#define FILAMENTCHANGE_YPOS 0
+#define FILAMENTCHANGE_ZADD 2
+#define FILAMENTCHANGE_FIRSTRETRACT -2
+#define FILAMENTCHANGE_FINALRETRACT -80
+
+#define FILAMENTCHANGE_FIRSTFEED 70
+#define FILAMENTCHANGE_FINALFEED 50
+#define FILAMENTCHANGE_RECFEED 5
+
+#define FILAMENTCHANGE_XYFEED 50
+#define FILAMENTCHANGE_EFEED 20
+#define FILAMENTCHANGE_RFEED 400
+#define FILAMENTCHANGE_EXFEED 2
+#define FILAMENTCHANGE_ZFEED 15
+
+#endif
+
+/*------------------------------------
+ADDITIONAL FEATURES SETTINGS
+*------------------------------------*/
+
+// Define Prusa filament runout sensor
+//#define FILAMENT_RUNOUT_SUPPORT
+
+#ifdef FILAMENT_RUNOUT_SUPPORT
+#define FILAMENT_RUNOUT_SENSOR 1
+#define FILAMENT_RUNOUT_SCRIPT "M600"
+#endif
+
+// temperature runaway
+#define TEMP_RUNAWAY_BED_HYSTERESIS 5
+#define TEMP_RUNAWAY_BED_TIMEOUT 360
+
+#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
+#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
+
+/*------------------------------------
+MOTOR CURRENT SETTINGS
+*------------------------------------*/
+
+// Motor Current setting for BIG RAMBo
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135}
+
+// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range
+#if MOTHERBOARD == BOARD_RAMBO_MINI_1_0 || MOTHERBOARD == BOARD_RAMBO_MINI_1_3
+#define MOTOR_CURRENT_PWM_RANGE 2000
+#define DEFAULT_PWM_MOTOR_CURRENT  {270, 830, 450} // {XY,Z,E}
+#define DEFAULT_PWM_MOTOR_CURRENT_LOUD  {540, 830, 500} // {XY,Z,E}
+#define Z_SILENT 0
+#define Z_HIGH_POWER 200
+#endif
+
+/*------------------------------------
+BED SETTINGS
+*------------------------------------*/
+
+// Define Mesh Bed Leveling system to enable it
+#define MESH_BED_LEVELING
+#ifdef MESH_BED_LEVELING
+
+#define MBL_Z_STEP 0.01
+
+// Mesh definitions
+#define MESH_MIN_X 35
+#define MESH_MAX_X 238
+#define MESH_MIN_Y 6
+#define MESH_MAX_Y 202
+
+// Mesh upsample definition
+#define MESH_NUM_X_POINTS 7
+#define MESH_NUM_Y_POINTS 7
+// Mesh measure definition
+#define MESH_MEAS_NUM_X_POINTS 3
+#define MESH_MEAS_NUM_Y_POINTS 3
+
+#define MESH_HOME_Z_CALIB 0.2
+#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+
+#define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 9     // Z probe to nozzle Y offset: -front +behind
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4  // Z probe to nozzle Z offset: -below (always!)
+#endif
+
+// Bed Temperature Control
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+// Bed temperature compensation settings
+#define BED_OFFSET 10
+#define BED_OFFSET_START 40
+#define BED_OFFSET_CENTER 50
+
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_bedKp 21.70
+#define  DEFAULT_bedKi 1.60
+#define  DEFAULT_bedKd 73.76
+#else
+#define  DEFAULT_bedKp 126.13
+#define  DEFAULT_bedKi 4.30
+#define  DEFAULT_bedKd 924.76
+#endif
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+//    #define  DEFAULT_bedKp 97.1
+//    #define  DEFAULT_bedKi 1.41
+//    #define  DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+/*-----------------------------------
+PREHEAT SETTINGS
+*------------------------------------*/
+
+#define FARM_PREHEAT_HOTEND_TEMP 250
+#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_FAN_SPEED 0
+
+#define PLA_PREHEAT_HOTEND_TEMP 215
+#define PLA_PREHEAT_HPB_TEMP 55
+#define PLA_PREHEAT_FAN_SPEED 0  
+
+#define ABS_PREHEAT_HOTEND_TEMP 255
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 0 
+
+#define HIPS_PREHEAT_HOTEND_TEMP 220
+#define HIPS_PREHEAT_HPB_TEMP 100
+#define HIPS_PREHEAT_FAN_SPEED 0 
+
+#define PP_PREHEAT_HOTEND_TEMP 254
+#define PP_PREHEAT_HPB_TEMP 100
+#define PP_PREHEAT_FAN_SPEED 0 
+
+#define PET_PREHEAT_HOTEND_TEMP 240
+#define PET_PREHEAT_HPB_TEMP 90
+#define PET_PREHEAT_FAN_SPEED 0 
+
+#define FLEX_PREHEAT_HOTEND_TEMP 230
+#define FLEX_PREHEAT_HPB_TEMP 50
+#define FLEX_PREHEAT_FAN_SPEED 0 
+
+/*------------------------------------
+THERMISTORS SETTINGS
+*------------------------------------*/
+
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" 
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a
+// 247 is Pt100 with 4k7 pullup and PT100 Amplifier
+// 110 is Pt100 with 1k pullup (non standard)
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP)
+#define TEMP_SENSOR_0 247
+#elif defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define TEMP_SENSOR_0 148
+#else
+#define TEMP_SENSOR_0 5
+#endif
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#if defined(E3D_PT100_BED_WITH_AMP)
+#define TEMP_SENSOR_BED 247
+#elif defined(E3D_PT100_BED_NO_AMP)
+#define TEMP_SENSOR_BED 148
+#else
+#define TEMP_SENSOR_BED 1
+#endif
+
+#define STACK_GUARD_TEST_VALUE 0xA2A2
+
+#define MAX_BED_TEMP_CALIBRATION 50
+#define MAX_HOTEND_TEMP_CALIBRATION 50
+
+#define MAX_E_STEPS_PER_UNIT 250
+#define MIN_E_STEPS_PER_UNIT 100
+
+#define Z_BABYSTEP_MIN -3999
+#define Z_BABYSTEP_MAX 0
+
+#define PINDA_PREHEAT_X 70
+#define PINDA_PREHEAT_Y -3
+#define PINDA_PREHEAT_Z 1
+#define PINDA_HEAT_T 120 //time in s
+
+#define PINDA_MIN_T 50
+#define PINDA_STEP_T 10
+#define PINDA_MAX_T 100
+
+#define PING_TIME 60 //time in s
+#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes
+#define PING_ALLERT_PERIOD 60 //time in s
+
+#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
+#define NC_BUTTON_LONG_PRESS 15 //time in s
+
+#define LONG_PRESS_TIME 1000 //time in ms for button long press 
+#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
+
+#define DEFAULT_PID_TEMP 210
+
+#ifdef SNMM
+#define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print
+#else
+#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print
+#endif
+
+#define END_FILE_SECTION 10000 //number of bytes from end of file used for checking if file is complete
+
+#define M600_TIMEOUT 600  //seconds
+
+#ifndef SNMM
+#define SUPPORT_VERBOSITY
+#endif
+
+#endif //__CONFIGURATION_PRUSA_H

Firmware/variants/1_75mm_MK25-RAMBo10a-E3Dv6full.h

@@ -0,0 +1,485 @@
+#ifndef CONFIGURATION_PRUSA_H
+#define CONFIGURATION_PRUSA_H
+
+/*------------------------------------
+ GENERAL SETTINGS
+ *------------------------------------*/
+
+// Printer revision
+#define PRINTER_TYPE PRINTER_MK25
+#define FILAMENT_SIZE "1_75mm_MK25"
+#define NOZZLE_TYPE "E3Dv6full"
+
+// Developer flag
+#define DEVELOPER
+
+// Printer name
+#define CUSTOM_MENDEL_NAME "Prusa i3 MK2.5"
+
+// Electronics
+#define MOTHERBOARD BOARD_RAMBO_MINI_1_0
+
+#define HEATBED_V2
+#define STEEL_SHEET
+#define TACH0PULLUP
+
+// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
+//#define E3D_PT100_EXTRUDER_WITH_AMP
+//#define E3D_PT100_EXTRUDER_NO_AMP
+//#define E3D_PT100_BED_WITH_AMP
+//#define E3D_PT100_BED_NO_AMP
+
+
+/*------------------------------------
+ AXIS SETTINGS
+ *------------------------------------*/
+
+// Steps per unit {X,Y,Z,E}
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,133}
+
+// Endstop inverting
+const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
+
+// Direction inverting
+#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_Z_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_E0_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+
+// Home position
+#define MANUAL_X_HOME_POS 0
+#define MANUAL_Y_HOME_POS -2.2
+#define MANUAL_Z_HOME_POS 0.2
+
+// Travel limits after homing
+#define X_MAX_POS 250
+#define X_MIN_POS 0
+#define Y_MAX_POS 210
+#define Y_MIN_POS -4
+#define Z_MAX_POS 210
+#define Z_MIN_POS 0.15
+
+// Canceled home position
+#define X_CANCEL_POS 50
+#define Y_CANCEL_POS 190
+
+//Pause print position
+#define X_PAUSE_POS 50
+#define Y_PAUSE_POS 190
+#define Z_PAUSE_LIFT 20
+
+#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
+#define HOMING_FEEDRATE {3000, 3000, 800, 0}  // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000
+
+#define DEFAULT_MAX_FEEDRATE          {200, 200, 12, 120}      // (mm/sec)   max feedrate (M203)
+#define DEFAULT_MAX_ACCELERATION      {1000, 1000, 200, 5000}  // (mm/sec^2) max acceleration (M201)
+
+
+#define DEFAULT_ACCELERATION          1250   // X, Y, Z and E max acceleration in mm/s^2 for printing moves (M204S)
+#define DEFAULT_RETRACT_ACCELERATION  1250   // X, Y, Z and E max acceleration in mm/s^2 for retracts (M204T)
+
+#define MANUAL_FEEDRATE {2700, 2700, 1000, 100}   // set the speeds for manual moves (mm/min)
+
+//number of bytes from end of the file to start check
+#define END_FILE_SECTION 10000
+
+#define Z_AXIS_ALWAYS_ON 1
+
+// New XYZ calibration
+#define NEW_XYZCAL
+
+// Fan check
+#define FANCHECK
+
+// Safety timer
+#define SAFETYTIMER
+
+// Filament sensor
+#define PAT9125
+
+
+
+//#define DEBUG_BUILD
+#ifdef DEBUG_BUILD
+//#define _NO_ASM
+#define DEBUG_DCODES //D codes
+#define DEBUG_STACK_MONITOR        //Stack monitor in stepper ISR
+//#define DEBUG_FSENSOR_LOG          //Reports fsensor status to serial
+//#define DEBUG_CRASHDET_COUNTERS  //Display crash-detection counters on LCD
+//#define DEBUG_RESUME_PRINT       //Resume/save print debug enable 
+//#define DEBUG_UVLO_AUTOMATIC_RECOVER // Power panic automatic recovery debug output 
+//#define DEBUG_DISABLE_XMINLIMIT  //x min limit ignored
+//#define DEBUG_DISABLE_XMAXLIMIT  //x max limit ignored
+//#define DEBUG_DISABLE_YMINLIMIT  //y min limit ignored
+//#define DEBUG_DISABLE_YMAXLIMIT  //y max limit ignored
+//#define DEBUG_DISABLE_ZMINLIMIT  //z min limit ignored
+//#define DEBUG_DISABLE_ZMAXLIMIT  //z max limit ignored
+//#define DEBUG_DISABLE_STARTMSGS //no startup messages 
+//#define DEBUG_DISABLE_MINTEMP   //mintemp error ignored
+//#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
+//#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
+//#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
+//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
+//#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
+//#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
+//#define DEBUG_BLINK_ACTIVE
+//#define DEBUG_DISABLE_FANCHECK     //disable fan check (no ISR INT7, check disabled)
+//#define DEBUG_DISABLE_FSENSORCHECK //disable fsensor check (no ISR INT7, check disabled)
+//#define DEBUG_DUMP_TO_2ND_SERIAL   //dump received characters to 2nd serial line
+//#define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message.
+//#define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display.
+#endif /* DEBUG_BUILD */
+
+
+/*------------------------------------
+ EXTRUDER SETTINGS
+ *------------------------------------*/
+
+// Mintemps
+#define HEATER_0_MINTEMP 15
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define BED_MINTEMP 15
+
+// Maxtemps
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define HEATER_0_MAXTEMP 410
+#else
+#define HEATER_0_MAXTEMP 305
+#endif
+#define HEATER_1_MAXTEMP 305
+#define HEATER_2_MAXTEMP 305
+#define BED_MAXTEMP 125
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_Kp 21.70
+#define  DEFAULT_Ki 1.60
+#define  DEFAULT_Kd 73.76
+#else
+// Define PID constants for extruder
+//#define  DEFAULT_Kp 40.925
+//#define  DEFAULT_Ki 4.875
+//#define  DEFAULT_Kd 86.085
+#define  DEFAULT_Kp 16.13
+#define  DEFAULT_Ki 1.1625
+#define  DEFAULT_Kd 56.23
+#endif
+
+// Extrude mintemp
+#define EXTRUDE_MINTEMP 180
+
+// Extruder cooling fans
+#define EXTRUDER_0_AUTO_FAN_PIN   8
+#define EXTRUDER_1_AUTO_FAN_PIN   -1
+#define EXTRUDER_2_AUTO_FAN_PIN   -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
+
+
+/*------------------------------------
+ LOAD/UNLOAD FILAMENT SETTINGS
+ *------------------------------------*/
+
+// Load filament commands
+#define LOAD_FILAMENT_0 "M83"
+#define LOAD_FILAMENT_1 "G1 E70 F400"
+#define LOAD_FILAMENT_2 "G1 E40 F100"
+
+// Unload filament commands
+#define UNLOAD_FILAMENT_0 "M83"
+#define UNLOAD_FILAMENT_1 "G1 E-80 F7000"
+
+/*------------------------------------
+ CHANGE FILAMENT SETTINGS
+ *------------------------------------*/
+
+// Filament change configuration
+#define FILAMENTCHANGEENABLE
+#ifdef FILAMENTCHANGEENABLE
+#define FILAMENTCHANGE_XPOS 211
+#define FILAMENTCHANGE_YPOS 0
+#define FILAMENTCHANGE_ZADD 2
+#define FILAMENTCHANGE_FIRSTRETRACT -2
+#define FILAMENTCHANGE_FINALRETRACT -80
+
+#define FILAMENTCHANGE_FIRSTFEED 70
+#define FILAMENTCHANGE_FINALFEED 50
+#define FILAMENTCHANGE_RECFEED 5
+
+#define FILAMENTCHANGE_XYFEED 50
+#define FILAMENTCHANGE_EFEED 20
+//#define FILAMENTCHANGE_RFEED 400
+#define FILAMENTCHANGE_RFEED 7000 / 60
+#define FILAMENTCHANGE_EXFEED 2
+#define FILAMENTCHANGE_ZFEED 15
+
+#endif
+
+/*------------------------------------
+ ADDITIONAL FEATURES SETTINGS
+ *------------------------------------*/
+
+// Define Prusa filament runout sensor
+//#define FILAMENT_RUNOUT_SUPPORT
+
+#ifdef FILAMENT_RUNOUT_SUPPORT
+#define FILAMENT_RUNOUT_SENSOR 1
+#endif
+
+// temperature runaway
+#define TEMP_RUNAWAY_BED_HYSTERESIS 5
+#define TEMP_RUNAWAY_BED_TIMEOUT 360
+
+#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
+#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
+
+/*------------------------------------
+ MOTOR CURRENT SETTINGS
+ *------------------------------------*/
+
+// Motor Current setting for BIG RAMBo
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135}
+
+// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range
+#if MOTHERBOARD == BOARD_RAMBO_MINI_1_0 || MOTHERBOARD == BOARD_RAMBO_MINI_1_3
+#define MOTOR_CURRENT_PWM_RANGE 2000
+#define DEFAULT_PWM_MOTOR_CURRENT  {270, 830, 450} // {XY,Z,E}
+#define DEFAULT_PWM_MOTOR_CURRENT_LOUD  {540, 830, 500} // {XY,Z,E}
+#define Z_SILENT 0
+#define Z_HIGH_POWER 200
+#endif
+
+/*------------------------------------
+ PAT9125 SETTINGS
+ *------------------------------------*/
+
+#define PAT9125_XRES			0
+#define PAT9125_YRES			255
+
+/*------------------------------------
+ BED SETTINGS
+ *------------------------------------*/
+
+// Define Mesh Bed Leveling system to enable it
+#define MESH_BED_LEVELING
+#ifdef MESH_BED_LEVELING
+
+#define MBL_Z_STEP 0.01
+
+// Mesh definitions
+#define MESH_MIN_X 35
+#define MESH_MAX_X 238
+#define MESH_MIN_Y 6
+#define MESH_MAX_Y 202
+
+// Mesh upsample definition
+#define MESH_NUM_X_POINTS 7
+#define MESH_NUM_Y_POINTS 7
+// Mesh measure definition
+#define MESH_MEAS_NUM_X_POINTS 3
+#define MESH_MEAS_NUM_Y_POINTS 3
+
+#define MESH_HOME_Z_CALIB 0.2
+#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+
+#define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
+#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4  // Z probe to nozzle Z offset: -below (always!)
+#endif
+
+// Bed Temperature Control
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+#define PIDTEMPBED
+//
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+// Bed temperature compensation settings
+#define BED_OFFSET 10
+#define BED_OFFSET_START 40
+#define BED_OFFSET_CENTER 50
+
+
+#ifdef PIDTEMPBED
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
+// Define PID constants for extruder with PT100
+#define  DEFAULT_bedKp 21.70
+#define  DEFAULT_bedKi 1.60
+#define  DEFAULT_bedKd 73.76
+#else
+#define  DEFAULT_bedKp 126.13
+#define  DEFAULT_bedKi 4.30
+#define  DEFAULT_bedKd 924.76
+#endif
+
+//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+//from pidautotune
+//    #define  DEFAULT_bedKp 97.1
+//    #define  DEFAULT_bedKi 1.41
+//    #define  DEFAULT_bedKd 1675.16
+
+// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+
+/*-----------------------------------
+ PREHEAT SETTINGS
+ *------------------------------------*/
+
+#define FARM_PREHEAT_HOTEND_TEMP 250
+#define FARM_PREHEAT_HPB_TEMP 40
+#define FARM_PREHEAT_FAN_SPEED 0
+
+#define PLA_PREHEAT_HOTEND_TEMP 215
+#define PLA_PREHEAT_HPB_TEMP 60
+#define PLA_PREHEAT_FAN_SPEED 0
+
+#define ABS_PREHEAT_HOTEND_TEMP 255
+#define ABS_PREHEAT_HPB_TEMP 100
+#define ABS_PREHEAT_FAN_SPEED 0
+
+#define HIPS_PREHEAT_HOTEND_TEMP 220
+#define HIPS_PREHEAT_HPB_TEMP 100
+#define HIPS_PREHEAT_FAN_SPEED 0
+
+#define PP_PREHEAT_HOTEND_TEMP 254
+#define PP_PREHEAT_HPB_TEMP 100
+#define PP_PREHEAT_FAN_SPEED 0
+
+#define PET_PREHEAT_HOTEND_TEMP 230
+#define PET_PREHEAT_HPB_TEMP 85
+#define PET_PREHEAT_FAN_SPEED 0
+
+#define FLEX_PREHEAT_HOTEND_TEMP 240
+#define FLEX_PREHEAT_HPB_TEMP 50
+#define FLEX_PREHEAT_FAN_SPEED 0
+
+/*------------------------------------
+ THERMISTORS SETTINGS
+ *------------------------------------*/
+
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a
+// 247 is Pt100 with 4k7 pullup and PT100 Amplifier
+// 110 is Pt100 with 1k pullup (non standard)
+
+#if defined(E3D_PT100_EXTRUDER_WITH_AMP)
+#define TEMP_SENSOR_0 247
+#elif defined(E3D_PT100_EXTRUDER_NO_AMP)
+#define TEMP_SENSOR_0 148
+#else
+#define TEMP_SENSOR_0 5
+#endif
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#if defined(E3D_PT100_BED_WITH_AMP)
+#define TEMP_SENSOR_BED 247
+#elif defined(E3D_PT100_BED_NO_AMP)
+#define TEMP_SENSOR_BED 148
+#else
+#define TEMP_SENSOR_BED 1
+#endif
+#define TEMP_SENSOR_PINDA 1
+
+#define STACK_GUARD_TEST_VALUE 0xA2A2
+
+#define MAX_BED_TEMP_CALIBRATION 50
+#define MAX_HOTEND_TEMP_CALIBRATION 50
+
+#define MAX_E_STEPS_PER_UNIT 250
+#define MIN_E_STEPS_PER_UNIT 100
+
+#define Z_BABYSTEP_MIN -3999
+#define Z_BABYSTEP_MAX 0
+
+#define PINDA_PREHEAT_X 20
+#define PINDA_PREHEAT_Y 60
+#define PINDA_PREHEAT_Z 0.15
+/*
+#define PINDA_PREHEAT_X 70
+#define PINDA_PREHEAT_Y -3
+#define PINDA_PREHEAT_Z 1*/
+#define PINDA_HEAT_T 120 //time in s
+
+#define PINDA_MIN_T 50
+#define PINDA_STEP_T 10
+#define PINDA_MAX_T 100
+
+#define PING_TIME 60 //time in s
+#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes
+#define PING_ALLERT_PERIOD 60 //time in s
+
+#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
+#define NC_BUTTON_LONG_PRESS 15 //time in s
+
+#define LONG_PRESS_TIME 1000 //time in ms for button long press
+#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
+
+#define DEFAULT_PID_TEMP 210
+
+#define MIN_PRINT_FAN_SPEED 75
+
+#ifdef SNMM
+#define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print
+#else
+#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print
+#endif
+
+#define M600_TIMEOUT 600  //seconds
+
+#define SUPPORT_VERBOSITY
+
+#endif //__CONFIGURATION_PRUSA_H