 Marek Bel
|
0b196da6fc
Migrate old vale of EEPROM_BABYSTEP_Z only if active sheet is not initialized.
|
5 vuotta sitten |
|
Marek Bel
|
32f435d1a0
Increase number of configurable steel sheets to 8. Move sheets into sub menu of HW setup.
|
5 vuotta sitten |
|
Marek Bel
|
f3bb72be64
Reset calibration status if there is no calibrated sheet after reset.
|
5 vuotta sitten |
|
Marek Bel
|
f64252b59b
Hide sheet switcher from main menu, if there are less than 2 sheets calibrated.
|
5 vuotta sitten |
|
Marek Bel
|
9692f94683
Move sheet menu up to be after Print from SD.
|
5 vuotta sitten |
|
Marek Bel
|
3903dc819a
Extract function next_initialized_sheet from change_sheet_from_menu(). Make it more general to depend on sizeof(Sheets::s) instead of hard coded value of 2.
|
5 vuotta sitten |
|
Marek Bel
|
33675c6d1e
Change default sheet names.
|
5 vuotta sitten |
|
Marek Bel
|
49bc11037c
Remove statements with no effect.
|
5 vuotta sitten |
|
DRracer
|
2bcffe32c4
Merge pull request #2140 from mkbel/preheat_asa_hotfix
|
5 vuotta sitten |
|
Marek Bel
|
bf2097342d
Add ASA preheat into mFilamentMenu();
|
5 vuotta sitten |
|
DRracer
|
6aaa40b9a3
Merge pull request #2134 from mkbel/fix_power_panic
|
5 vuotta sitten |
|
DRracer
|
a1e68c3d7f
Merge pull request #2135 from prusa3d/MK3_3.8.0
|
5 vuotta sitten |
|
Marek Bel
|
159a1a70d8
Update documentation.
|
5 vuotta sitten |
|
Marek Bel
|
c27fcf9cff
Increase version to 3.8.0-RC2 and build number to 2639.
|
5 vuotta sitten |
|
Marek Běl
|
51d01ddd6f
Merge pull request #2133 from mkbel/fix_cmdqueue_debug
|
5 vuotta sitten |
|
Marek Bel
|
52cb37770b
Fix repeated power panic restarted print from beginning or jumped at most 65536 B back in file printed from SD card.
|
5 vuotta sitten |
|
Marek Bel
|
3eb36ca194
Fix cmdqueue_dump_to_serial.
|
5 vuotta sitten |
|
XPila
|
5bb510dd2a
Merge pull request #2129 from DRracer/bed-noise-performance
|
5 vuotta sitten |
|
DRracer
|
c6df3fe012
Merge pull request #2127 from DRracer/code-size-reduction-1
|
5 vuotta sitten |
|
DRracer
|
7a38a985d7
Merge pull request #2123 from mkbel/fix_disable_crash_detection
|
5 vuotta sitten |
|
DRracer
|
a7c2aec04c
Code size reduced by almost 5KB
|
5 vuotta sitten |
|
Marek Bel
|
3ed6d0637c
Re-enable tmc2130_sg_stop_on_crash only if crash detection enabled from menu.
|
5 vuotta sitten |
|
Marek Bel
|
f204cdea81
Refactor
|
5 vuotta sitten |
|
DRracer
|
f07635d08a
Merge pull request #2116 from mkbel/fix_mmu_lay1cal
|
5 vuotta sitten |
|
DRracer
|
d44a46b349
Merge pull request #2120 from mkbel/fix_power_panic_2
|
5 vuotta sitten |
|
Marek Bel
|
f0642f88f1
Fix power panic broken when PSU_Delta defined.
|
5 vuotta sitten |
|
Marek Bel
|
170c1ea866
Split first layer calibration load filament and intro line into separate steps. If load fails, pause print apparently flushes command buffer and intro line is not printed after issue is resolved.
|
5 vuotta sitten |
|
Marek Bel
|
e53734895f
Make MMU load failed blocking to workaround lack of resume print menu item.
|
5 vuotta sitten |
|
Marek Bel
|
1036c4f755
Do not precede first layer calibration without filament if print is paused due to MMU load failed.
|
5 vuotta sitten |
|
DRracer
|
4c22ec234f
Merge pull request #2109 from mkbel/add_ASA
|
5 vuotta sitten |
