 bubnikv
|
986b286803
Reworked calculation of the trapezoidal ramps inside the planner.
|
8 years ago |
|
bubnikv
|
5c56e472fe
Show the Toshiba FlashAir IP address in the menu.
|
8 years ago |
|
bubnikv
|
2e66fdf84a
Merge branch 'MK2' of https://github.com/Prusa3D/Prusa-Firmware into MK2
|
8 years ago |
|
bubnikv
|
562c089e17
Initial implementation of the Toshiba FlashAir support:
|
8 years ago |
|
akukan
|
c8c92f8ae5
PLA preheat settings for MK2 set to 215/55
|
8 years ago |
|
akukan
|
e9910a9078
Print farm confirmation
|
8 years ago |
|
akukan
|
1b2676baac
Farm monitoring
|
8 years ago |
|
bubnikv
|
ea6a948c6b
Removed the dual carriage code for readibility.
|
8 years ago |
|
bubnikv
|
2e6e4542c9
Undo babystepping in Z before G28 / G80, if applied already.
|
8 years ago |
|
bubnikv
|
3c21438392
In addition to the firmware version number, store the "PRUSA3D"
|
8 years ago |
|
bubnikv
|
d825c5ffac
Write the current firmware version into first 8 bytes of the EEPROM,
|
8 years ago |
|
bubnikv
|
d4e332112b
Reset babystepping value on startup, if the Z live adjust is off.
|
8 years ago |
|
bubnikv
|
591e81777a
"Printer has not been calibrated yet, calibrate Z" message on startup,
|
8 years ago |
|
bubnikv
|
208976f397
Ignore extended ASCII characters. These characters have no meaning in the G-code apart from the file names
|
8 years ago |
|
bubnikv
|
0b372bfc94
Added a new feature to the "M115" code:
|
8 years ago |
|
bubnikv
|
d7c75f2060
Updated soft end stops with the skew calibration active.
|
8 years ago |
|
bubnikv
|
a88c0a30e7
Fixed a non-C++ implementation of the PRUSA specific G-Codes.
|
8 years ago |
|
bubnikv
|
1394e7efc6
Skew calibration: Yet another improvement of the search algorithm
|
8 years ago |
|
bubnikv
|
58b2aa9fb8
Improvement of the bed skew calibration.
|
8 years ago |
|
bubnikv
|
0389b23514
Rewrote the fitting routine of the induction sensor points to the measured points
|
8 years ago |
|
bubnikv
|
677c13fc9a
Improved the bed auto calibration at the Y=0 edge of the bed.
|
8 years ago |
|
bubnikv
|
80971237b8
Polished the bed skew and shift calibration.
|
8 years ago |
|
bubnikv
|
c24f3369d7
Fixed a bug in babystepping: The babystep value will be written to EEPROM
|
8 years ago |
|
bubnikv
|
78ebd522b6
Removed support for DELTA, SCARA and BARICUDA.
|
8 years ago |
|
bubnikv
|
08bf6acf1b
Fixed ".." label when leaving a subdirectory.
|
8 years ago |
|
bubnikv
|
d9da3c4c7f
Bugfix of the "Move Z carriages up" step.
|
8 years ago |
|
bubnikv
|
6cff4b92ff
Automatic bed calibration by searching the 3x3 point matrix.
|
8 years ago |
|
michalprusa
|
e115c5145f
MK2 Config files and hex output added
|
8 years ago |
|
michalprusa
|
a4a80b3eb7
MK2 Firmware release.
|
8 years ago |
|
michalprusa
|
7361f620d3
Extrude mintemp lowered for wax filaments support
|
8 years ago |
