 Marek Bel
|
cd7805ba46
Document
|
преди 5 години |
|
Marek Bel
|
0b196da6fc
Migrate old vale of EEPROM_BABYSTEP_Z only if active sheet is not initialized.
|
преди 5 години |
|
Marek Bel
|
32f435d1a0
Increase number of configurable steel sheets to 8. Move sheets into sub menu of HW setup.
|
преди 5 години |
|
Marek Bel
|
f3bb72be64
Reset calibration status if there is no calibrated sheet after reset.
|
преди 5 години |
|
Marek Bel
|
f64252b59b
Hide sheet switcher from main menu, if there are less than 2 sheets calibrated.
|
преди 5 години |
|
Marek Bel
|
9692f94683
Move sheet menu up to be after Print from SD.
|
преди 5 години |
|
Marek Bel
|
3903dc819a
Extract function next_initialized_sheet from change_sheet_from_menu(). Make it more general to depend on sizeof(Sheets::s) instead of hard coded value of 2.
|
преди 5 години |
|
Marek Bel
|
33675c6d1e
Change default sheet names.
|
преди 5 години |
|
Marek Bel
|
49bc11037c
Remove statements with no effect.
|
преди 5 години |
|
DRracer
|
2bcffe32c4
Merge pull request #2140 from mkbel/preheat_asa_hotfix
|
преди 5 години |
|
Marek Bel
|
bf2097342d
Add ASA preheat into mFilamentMenu();
|
преди 5 години |
|
DRracer
|
6aaa40b9a3
Merge pull request #2134 from mkbel/fix_power_panic
|
преди 5 години |
|
DRracer
|
a1e68c3d7f
Merge pull request #2135 from prusa3d/MK3_3.8.0
|
преди 5 години |
|
Marek Bel
|
159a1a70d8
Update documentation.
|
преди 5 години |
|
Marek Bel
|
c27fcf9cff
Increase version to 3.8.0-RC2 and build number to 2639.
|
преди 5 години |
|
Marek Běl
|
51d01ddd6f
Merge pull request #2133 from mkbel/fix_cmdqueue_debug
|
преди 5 години |
|
Marek Bel
|
52cb37770b
Fix repeated power panic restarted print from beginning or jumped at most 65536 B back in file printed from SD card.
|
преди 5 години |
|
Marek Bel
|
3eb36ca194
Fix cmdqueue_dump_to_serial.
|
преди 5 години |
|
XPila
|
5bb510dd2a
Merge pull request #2129 from DRracer/bed-noise-performance
|
преди 5 години |
|
DRracer
|
c6df3fe012
Merge pull request #2127 from DRracer/code-size-reduction-1
|
преди 5 години |
|
DRracer
|
7a38a985d7
Merge pull request #2123 from mkbel/fix_disable_crash_detection
|
преди 5 години |
|
DRracer
|
a7c2aec04c
Code size reduced by almost 5KB
|
преди 5 години |
|
Marek Bel
|
3ed6d0637c
Re-enable tmc2130_sg_stop_on_crash only if crash detection enabled from menu.
|
преди 5 години |
|
Marek Bel
|
f204cdea81
Refactor
|
преди 5 години |
|
DRracer
|
f07635d08a
Merge pull request #2116 from mkbel/fix_mmu_lay1cal
|
преди 5 години |
|
DRracer
|
d44a46b349
Merge pull request #2120 from mkbel/fix_power_panic_2
|
преди 5 години |
|
Marek Bel
|
f0642f88f1
Fix power panic broken when PSU_Delta defined.
|
преди 5 години |
|
Marek Bel
|
170c1ea866
Split first layer calibration load filament and intro line into separate steps. If load fails, pause print apparently flushes command buffer and intro line is not printed after issue is resolved.
|
преди 5 години |
|
Marek Bel
|
e53734895f
Make MMU load failed blocking to workaround lack of resume print menu item.
|
преди 5 години |
|
Marek Bel
|
1036c4f755
Do not precede first layer calibration without filament if print is paused due to MMU load failed.
|
преди 5 години |
