# Translation of Prusa-Firmware into German.
#
msgid ""
msgstr ""
"MIME-Version: 1.0\n"
"Content-Type: text/plain; charset=UTF-8\n"
"Content-Transfer-Encoding: 8bit\n"
"Language: de\n"
"Project-Id-Version: Prusa-Firmware\n"
"POT-Creation-Date: čt 1. lis 2018 19:29:33\n"
"PO-Revision-Date: čt 1. lis 2018 19:29:33\n"
"Language-Team: \n"
"X-Generator: Poedit 2.0.7\n"
"X-Poedit-SourceCharset: UTF-8\n"
"Last-Translator: \n"
"Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"

# MSG_PLANNER_BUFFER_BYTES
#: Marlin_main.cpp:1180
msgid "  PlannerBufferBytes: "
msgstr " PlannerPufferBytes: "

# MSG_ERR_COLD_EXTRUDE_STOP
#: planner.cpp:761
msgid " cold extrusion prevented"
msgstr " stopp, Extruder kalt"

# MSG_FREE_MEMORY
#: Marlin_main.cpp:1178
msgid " Free Memory: "
msgstr " Freier Speicher: "

# MSG_CONFIGURATION_VER
#: Marlin_main.cpp:1168
msgid " Last Updated: "
msgstr " Letztes Update: "

# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
#: messages.c:44
msgid " of 4"
msgstr " von 4"

# MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
#: messages.c:61
msgid " of 9"
msgstr " von 9"

# MSG_MEASURED_OFFSET
#: ultralcd.cpp:2698
msgid "[0;0] point offset"
msgstr "[0;0] Punktversatz"

# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
#: ultralcd.cpp:3977
msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
msgstr "\x1b[2JCrash Erkennung kann\x1b[1;0Hnur im Modus Normal\x1b[2;0Hgenutzt werden"

# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
#: ultralcd.cpp:3989
msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
msgstr "\x1b[2JWARNUNG:\x1b[1;0HCrash Erkennung\x1b[2;0Hdeaktiviert im\x1b[3;0HStealth Modus"

# MSG_BABYSTEPPING_Z c=20
#: ultralcd.cpp:2827
msgid "Adjusting Z"
msgstr "Z wurde eingestellt"

# MSG_SELFTEST_CHECK_ALLCORRECT c=20
#: ultralcd.cpp:7018
msgid "All correct      "
msgstr "Alles richtig "

# MSG_WIZARD_DONE c=20 r=8
#: messages.c:104
msgid "All is done. Happy printing!"
msgstr "Alles abgeschlossen. Viel Spass beim Drucken!"

# MSG_PRESS c=20
#: ultralcd.cpp:2251
msgid "and press the knob"
msgstr "und Knopf druecken"

# MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
#: ultralcd.cpp:3125
msgid "Are left and right Z~carriages all up?"
msgstr "Sind linke+rechte Z- Schlitten ganz oben?"

# MSG_AUTO_DEPLETE_ON c=17 r=1
#: ultralcd.cpp:4804
msgid "Auto deplete [on]"
msgstr "Restemodus   [an]"

#  MSG_AUTO_DEPLETE_OFF c=17 r=1
#: ultralcd.cpp:4805
msgid "Auto deplete[off]"
msgstr "Restemodus  [aus]"

# MSG_AUTO_HOME
#: messages.c:11
msgid "Auto home"
msgstr "Startposition"

# MSG_AUTOLOAD_FILAMENT c=17
#: ultralcd.cpp:5782
msgid "AutoLoad filament"
msgstr "Auto-Laden Filament"

# MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
#: ultralcd.cpp:4004
msgid "Autoloading filament available only when filament sensor is turned on..."
msgstr "Automatisches Laden Filament nur bei einge schaltetem Filament- sensor verfuegbar..."

# MSG_AUTOLOADING_ENABLED c=20 r=4
#: ultralcd.cpp:2424
msgid "Autoloading filament is active, just press the knob and insert filament..."
msgstr "Automatisches Laden Filament ist aktiv, Knopf druecken und  Filament einlegen..."

# MSG_SELFTEST_AXIS_LENGTH
#: ultralcd.cpp:6791
msgid "Axis length"
msgstr "Achsenlaenge"

# MSG_SELFTEST_AXIS
#: ultralcd.cpp:6793
msgid "Axis"
msgstr "Achse"

# MSG_SELFTEST_BEDHEATER
#: ultralcd.cpp:6735
msgid "Bed / Heater"
msgstr "Bett / Heizung"

# MSG_BED_DONE
#: messages.c:16
msgid "Bed done"
msgstr "Bett OK"

# MSG_BED_HEATING
#: messages.c:17
msgid "Bed Heating"
msgstr "Bett aufwaermen"

# MSG_BED_CORRECTION_MENU
#: ultralcd.cpp:4906
msgid "Bed level correct"
msgstr "Ausgleich Bett ok"

# MSG_BED_LEVELING_FAILED_POINT_LOW c=20 r=4
#: messages.c:18
msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
msgstr "Z-Kal. fehlgeschlg. Sensor nicht ausgeloest. Schmutzige Duese? Warte auf Reset."

# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
#: Marlin_main.cpp:4445
msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
msgstr "Z-Kalibrierung fehl- geschlagen. Sensor getrennt/Kabelbruch? Warte auf Reset."

# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
#: Marlin_main.cpp:4449
msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
msgstr "Z-Kalibrierung fehl- geschlagen. Sensor zu hoch ausgeloest. Warte auf Reset."

# MSG_BED
#: messages.c:15
msgid "Bed"
msgstr "Bett"

# MSG_MENU_BELT_STATUS c=15 r=1
#: ultralcd.cpp:2050
msgid "Belt status"
msgstr "Gurtstatus"

# MSG_RECOVER_PRINT c=20 r=2
#: messages.c:74
msgid "Blackout occurred. Recover print?"
msgstr "Stromausfall! Druck wiederherstellen?"

# MSG_CALIBRATE_BED
#: ultralcd.cpp:4895
msgid "Calibrate XYZ"
msgstr "Kalibrierung XYZ"

# MSG_HOMEYZ
#: messages.c:53
msgid "Calibrate Z"
msgstr "Kalibrierung Z"

# MSG_CALIBRATE_PINDA c=17 r=1
#: ultralcd.cpp:4185
msgid "Calibrate"
msgstr "Kalibrieren"

# MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
#: ultralcd.cpp:3078
msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
msgstr "XYZ Kalibrieren: Drehen Sie den Knopf bis der obere Anschlag erreicht wird. Anschliessend den Knopf druecken."

# MSG_CALIBRATE_Z_AUTO c=20 r=2
#: messages.c:20
msgid "Calibrating Z"
msgstr "Kalibrierung Z"

# MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
#: ultralcd.cpp:3078
msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
msgstr "Z Kalibrieren: Drehen Sie den Knopf bis der obere Anschlag erreicht wird. Anschliessend den Knopf druecken."

# MSG_HOMEYZ_DONE
#: ultralcd.cpp:738
msgid "Calibration done"
msgstr "Kalibrierung OK"

# MSG_MENU_CALIBRATION
#: messages.c:62
msgid "Calibration"
msgstr "Kalibrierung"

# 
#: ultralcd.cpp:4316
#, fuzzy
msgid "Cancel"
msgstr ""

# MSG_SD_CANT_ENTER_SUBDIR
#: cardreader.cpp:662
msgid "Cannot enter subdir: "
msgstr "Kann Unterverzeichnis nicht oeffnen: "

# MSG_SD_INSERTED
#: ultralcd.cpp:7369
msgid "Card inserted"
msgstr "SD Karte eingesetzt"

# MSG_SD_REMOVED
#: ultralcd.cpp:7375
msgid "Card removed"
msgstr "SD Karte entfernt"

# MSG_NOT_COLOR
#: ultralcd.cpp:2353
msgid "Color not correct"
msgstr "Falsche Farbe"

# MSG_COOLDOWN
#: messages.c:23
msgid "Cooldown"
msgstr "Abkuehlen"

# 
#: ultralcd.cpp:4118
#, fuzzy
msgid "Copy selected language from XFLASH?"
msgstr ""

# MSG_CRASHDETECT_ON
#: messages.c:27
msgid "Crash det.   [on]"
msgstr "Crash Erk.   [an]"

# MSG_CRASHDETECT_NA
#: messages.c:25
msgid "Crash det.  [N/A]"
msgstr "Crash Erk.   [nv]"

# MSG_CRASHDETECT_OFF
#: messages.c:26
msgid "Crash det.  [off]"
msgstr "Crash Erk.  [aus]"

# MSG_CRASH_DETECTED c=20 r=1
#: messages.c:24
msgid "Crash detected."
msgstr "Crash erkannt."

# 
#: Marlin_main.cpp:601
msgid "Crash detected. Resume print?"
msgstr "Crash erkannt. Druck fortsetzen?"

# MSG_CURRENT c=19 r=1
#: ultralcd.cpp:5046
msgid "Current"
msgstr "Aktuelles"

# MSG_DATE c=17 r=1
#: ultralcd.cpp:2150
msgid "Date:"
msgstr "Datum:"

# MSG_DISABLE_STEPPERS
#: ultralcd.cpp:4798
msgid "Disable steppers"
msgstr "Motoren aus"

# MSG_BABYSTEP_Z_NOT_SET c=20 r=12
#: messages.c:14
msgid "Distance between tip of the nozzle and the bed surface has not been set yet. Please follow the manual, chapter First steps, section First layer calibration."
msgstr "Der Abstand zwischen der Spitze der Duese und dem Bett ist noch nicht eingestellt. Bitte folgen Sie dem Handbuch, Kapitel Erste Schritte, Abschnitt Erste Schicht Kalibrierung."

# MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
#: ultralcd.cpp:4561
msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
msgstr "Moechten Sie den letzten Schritt wiederholen, um den Abstand zwischen Duese und Druckbett neu einzustellen?"

# MSG_EXTRUDER_CORRECTION c=9
#: ultralcd.cpp:4621
msgid "E-correct"
msgstr "E-Korrektur"

# MSG_EJECT_FILAMENT c=17 r=1
#: ultralcd.cpp:5769
msgid "Eject filament"
msgstr "Filamentauswurf"

# MSG_EJECT_FILAMENT1 c=17 r=1
#: ultralcd.cpp:5300
msgid "Eject filament 1"
msgstr "Filamentauswurf 1"

# MSG_EJECT_FILAMENT2 c=17 r=1
#: ultralcd.cpp:5301
msgid "Eject filament 2"
msgstr "Filamentauswurf 2"

# MSG_EJECT_FILAMENT3 c=17 r=1
#: ultralcd.cpp:5302
msgid "Eject filament 3"
msgstr "Filamentauswurf 3"

# MSG_EJECT_FILAMENT4 c=17 r=1
#: ultralcd.cpp:5303
msgid "Eject filament 4"
msgstr "Filamentauswurf 4"

# MSG_EJECT_FILAMENT5 c=17 r=1
#: ultralcd.cpp:5304
msgid "Eject filament 5"
msgstr "Filamentauswurf 5"

# 
#: ultralcd.cpp:4516
#, fuzzy
msgid "Eject"
msgstr ""

# MSG_EJECTING_FILAMENT c=20 r=1
#: mmu.cpp:1044
msgid "Ejecting filament"
msgstr "Werfe Filament aus"

# MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
#: ultralcd.cpp:6759
msgid "Endstop not hit"
msgstr "Ende nicht getroffen"

# MSG_SELFTEST_ENDSTOP
#: ultralcd.cpp:6753
msgid "Endstop"
msgstr "Endanschlag"

# MSG_ENDSTOPS_HIT
#: messages.c:30
msgid "endstops hit: "
msgstr "Endanschlag erreicht: "

# MSG_SELFTEST_ENDSTOPS
#: ultralcd.cpp:6741
msgid "Endstops"
msgstr "Endschalter"

# MSG_Enqueing
#: 
#, fuzzy
msgid "enqueing \x22"
msgstr ""

# MSG_STACK_ERROR c=20 r=4
#: ultralcd.cpp:5817
msgid "Error - static memory has been overwritten"
msgstr "Fehler - statischer Speicher wurde ueberschrieben"

# MSG_SD_ERR_WRITE_TO_FILE
#: messages.c:78
msgid "error writing to file"
msgstr "Fehler beim Schreiben in Datei"

# MSG_FSENS_NOT_RESPONDING c=20 r=4
#: ultralcd.cpp:4017
msgid "ERROR: Filament sensor is not responding, please check connection."
msgstr "FEHLER: Filament- sensor reagiert nicht, bitte  Verbindung pruefen."

# MSG_ERROR
#: messages.c:33
msgid "ERROR:"
msgstr "FEHLER:"

# 
#: Marlin_main.cpp:981
#, fuzzy
msgid "External SPI flash W25X20CL not responding."
msgstr ""

# 
#: ultralcd.cpp:5328
#, fuzzy
msgid "Extruder 1"
msgstr ""

# 
#: ultralcd.cpp:5329
#, fuzzy
msgid "Extruder 2"
msgstr ""

# 
#: ultralcd.cpp:5330
#, fuzzy
msgid "Extruder 3"
msgstr ""

# 
#: ultralcd.cpp:5331
#, fuzzy
msgid "Extruder 4"
msgstr ""

# MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
#: ultralcd.cpp:7027
msgid "Extruder fan:"
msgstr "Extruder Luefter:"

# MSG_INFO_EXTRUDER c=15 r=1
#: ultralcd.cpp:2181
msgid "Extruder info"
msgstr "Extruder Info"

# MSG_MOVE_E
#: messages.c:34
#, fuzzy
msgid "Extruder"
msgstr ""

# MSG_FSENS_AUTOLOAD_ON c=17 r=1
#: ultralcd.cpp:4659
msgid "F. autoload  [on]"
msgstr "F.Autoladen  [an]"

# MSG_FSENS_AUTOLOAD_NA c=17 r=1
#: messages.c:48
msgid "F. autoload [N/A]"
msgstr "F. Autoload  [nv]"

# MSG_FSENS_AUTOLOAD_OFF c=17 r=1
#: ultralcd.cpp:4661
msgid "F. autoload [off]"
msgstr "F. Autoload [aus]"

# MSG_FAN_SPEED c=14
#: messages.c:36
msgid "Fan speed"
msgstr "Luefter-Tempo"

# MSG_SELFTEST_FAN c=20
#: messages.c:83
msgid "Fan test"
msgstr "Lueftertest"

# MSG_FANS_CHECK_ON c=17 r=1
#: ultralcd.cpp:4809
msgid "Fans check   [on]"
msgstr "Luefter Chk. [an]"

# MSG_FANS_CHECK_OFF c=17 r=1
#: ultralcd.cpp:4811
msgid "Fans check  [off]"
msgstr "Luefter Chk.[aus]"

# MSG_FSENSOR_ON
#: messages.c:50
msgid "Fil. sensor  [on]"
msgstr "Fil. Sensor  [an]"

# MSG_RESPONSE_POOR c=20 r=2
#: Marlin_main.cpp:3085
msgid "Fil. sensor response is poor, disable it?"
msgstr "Fil. Sensorsignal ist schlecht, ausschalten?"

# MSG_FSENSOR_NA
#: ultralcd.cpp:4639
msgid "Fil. sensor [N/A]"
msgstr "Fil. Sensor  [nv]"

# MSG_FSENSOR_OFF
#: messages.c:49
msgid "Fil. sensor [off]"
msgstr "Fil. Sensor [aus]"

# MSG_FILAMENT_CLEAN c=20 r=2
#: messages.c:37
msgid "Filament extruding & with correct color?"
msgstr "Filament extrudiert + richtige Farbe?"

# MSG_NOT_LOADED c=19
#: ultralcd.cpp:2349
msgid "Filament not loaded"
msgstr "Fil. nicht geladen"

# MSG_FILAMENT_SENSOR c=20
#: ultralcd.cpp:6807
msgid "Filament sensor"
msgstr "Filamentsensor"

# MSG_SELFTEST_FILAMENT_SENSOR c=18
#: ultralcd.cpp:7036
msgid "Filament sensor:"
msgstr "Filamentsensor:"

# MSG_FILAMENT_USED c=19 r=1
#: ultralcd.cpp:2504
msgid "Filament used"
msgstr "Filament benutzt"

# MSG_PRINT_TIME c=19 r=1
#: ultralcd.cpp:2506
msgid "Print time"
msgstr "Druckzeit"

# MSG_FILE_INCOMPLETE c=20 r=2
#: ultralcd.cpp:7153
msgid "File incomplete. Continue anyway?"
msgstr "Datei unvollstaendig Trotzdem fortfahren?"

# MSG_FINISHING_MOVEMENTS c=20 r=1
#: messages.c:45
msgid "Finishing movements"
msgstr "Bewegung beenden"

# MSG_V2_CALIBRATION c=17 r=1
#: ultralcd.cpp:4886
msgid "First layer cal."
msgstr "Erste-Schicht Kal."

# MSG_WIZARD_SELFTEST c=20 r=8
#: ultralcd.cpp:4458
msgid "First, I will run the selftest to check most common assembly problems."
msgstr "Zunaechst fuehre ich den Selbsttest durch, um die haeufigsten Probleme beim Zusammenbau zu ueberpruefen."

# MSG_FLOW
#: ultralcd.cpp:5890
msgid "Flow"
msgstr "Durchfluss"

# MSG_PRUSA3D_FORUM
#: ultralcd.cpp:2143
#, fuzzy
msgid "forum.prusa3d.com"
msgstr ""

# MSG_SELFTEST_COOLING_FAN c=20
#: messages.c:80
msgid "Front print fan?"
msgstr "Vorderer Luefter?"

# MSG_BED_CORRECTION_FRONT c=14 r=1
#: ultralcd.cpp:2887
msgid "Front side[um]"
msgstr "Vorne [um]"

# MSG_SELFTEST_FANS
#: ultralcd.cpp:6799
msgid "Front/left fans"
msgstr "Vorderer/linke Luefter"

# MSG_SELFTEST_HEATERTHERMISTOR
#: ultralcd.cpp:6729
msgid "Heater/Thermistor"
msgstr "Heizung/Thermistor"

# MSG_BED_HEATING_SAFETY_DISABLED
#: Marlin_main.cpp:7316
msgid "Heating disabled by safety timer."
msgstr "Heizung durch Sicherheitstimer deaktiviert."

# MSG_HEATING_COMPLETE c=20
#: messages.c:52
msgid "Heating done."
msgstr "Aufwaermen OK."

# MSG_HEATING
#: messages.c:51
msgid "Heating"
msgstr "Aufwaermen"

# MSG_WIZARD_WELCOME c=20 r=7
#: ultralcd.cpp:4437
msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
msgstr "Hallo, ich bin Ihr Original Prusa i3 Drucker. Moechten Sie, dass ich Sie durch den Einrich- tungsablauf fuehre?"

# MSG_PRUSA3D_HOWTO
#: ultralcd.cpp:2144
#, fuzzy
msgid "howto.prusa3d.com"
msgstr ""

# 
#: ultralcd.cpp:5775
#, fuzzy
msgid "Change extruder"
msgstr ""

# MSG_FILAMENTCHANGE
#: messages.c:42
msgid "Change filament"
msgstr "Filament-Wechsel"

# MSG_CHANGE_SUCCESS
#: ultralcd.cpp:2262
msgid "Change success!"
msgstr "Wechsel erfolgr.!"

# MSG_CORRECTLY c=20
#: ultralcd.cpp:2341
msgid "Changed correctly?"
msgstr "Wechsel ok?"

# MSG_SELFTEST_CHECK_BED c=20
#: messages.c:86
msgid "Checking bed     "
msgstr "Pruefe Bett "

# MSG_SELFTEST_CHECK_ENDSTOPS c=20
#: ultralcd.cpp:7009
msgid "Checking endstops"
msgstr "Pruefe Endschalter"

# MSG_SELFTEST_CHECK_HOTEND c=20
#: ultralcd.cpp:7010
msgid "Checking hotend  "
msgstr "Pruefe Duese  "

# MSG_SELFTEST_CHECK_FSENSOR c=20
#: messages.c:87
msgid "Checking sensors "
msgstr "Pruefe Sensoren "

# MSG_SELFTEST_CHECK_X c=20
#: ultralcd.cpp:7011
msgid "Checking X axis  "
msgstr "Pruefe X Achse "

# MSG_SELFTEST_CHECK_Y c=20
#: ultralcd.cpp:7012
msgid "Checking Y axis  "
msgstr "Pruefe Y Achse "

# MSG_SELFTEST_CHECK_Z c=20
#: ultralcd.cpp:7013
msgid "Checking Z axis  "
msgstr "Pruefe Z Achse "

# MSG_ERR_CHECKSUM_MISMATCH
#: cmdqueue.cpp:444
msgid "checksum mismatch, Last Line: "
msgstr "Pruefsummenfehler, Letzte Zeile: "

# MSG_CHOOSE_EXTRUDER c=20 r=1
#: messages.c:54
msgid "Choose extruder:"
msgstr "Extruder waehlen:"

# MSG_CHOOSE_FILAMENT c=20 r=1
#: messages.c:55
msgid "Choose filament:"
msgstr "Filament waehlen:"

# MSG_FILAMENT c=17 r=1
#: messages.c:35
msgid "Filament"
msgstr "Filament"

# MSG_WIZARD_XYZ_CAL c=20 r=8
#: ultralcd.cpp:4467
msgid "I will run xyz calibration now. It will take approx. 12 mins."
msgstr "Ich werde jetzt die XYZ-Kalibrierung durchfuehren. Es wird ca. 12 Minuten dauern."

# MSG_WIZARD_Z_CAL c=20 r=8
#: ultralcd.cpp:4473
msgid "I will run z calibration now."
msgstr "Ich werde jetzt die Z Kalibrierung durchfuehren."

# MSG_WIZARD_V2_CAL_2 c=20 r=12
#: ultralcd.cpp:4555
msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
msgstr "Ich werde jetzt eine Linie drucken. Waehrend des Druckes koennen Sie die Duese allmaehlich senken, indem Sie den Knopf drehen, bis Sie die optimale Hoehe erreichen. Sehen Sie sich die Bilder in unserem Handbuch im Kapitel Kalibrierung an."

# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
#: mesh_bed_calibration.cpp:2481
msgid "Improving bed calibration point"
msgstr "Verbessere Bett Kalibrierpunkt"

# MSG_WATCH
#: messages.c:102
msgid "Info screen"
msgstr "Infoanzeige"

# MSG_FILAMENT_LOADING_T0 c=20 r=4
#: messages.c:38
msgid "Insert filament into extruder 1. Click when done."
msgstr "Filament in Extruder 1 einlegen. Klicken wenn fertig."

# MSG_FILAMENT_LOADING_T1 c=20 r=4
#: messages.c:39
msgid "Insert filament into extruder 2. Click when done."
msgstr "Filament in Extruder 2 einlegen. Klicken wenn fertig."

# MSG_FILAMENT_LOADING_T2 c=20 r=4
#: messages.c:40
msgid "Insert filament into extruder 3. Click when done."
msgstr "Filament in Extruder 3 einlegen. Klicken wenn fertig."

# MSG_FILAMENT_LOADING_T3 c=20 r=4
#: messages.c:41
msgid "Insert filament into extruder 4. Click when done."
msgstr "Filament in Extruder 4 einlegen. Klicken wenn fertig."

# 
#: ultralcd.cpp:4486
#, fuzzy
msgid "Is filament 1 loaded?"
msgstr ""

# MSG_INSERT_FILAMENT c=20
#: ultralcd.cpp:2248
msgid "Insert filament"
msgstr "Filament einlegen"

# MSG_WIZARD_FILAMENT_LOADED c=20 r=2
#: ultralcd.cpp:4489
msgid "Is filament loaded?"
msgstr "Ist das Filament geladen?"

# MSG_WIZARD_PLA_FILAMENT c=20 r=2
#: ultralcd.cpp:4549
msgid "Is it PLA filament?"
msgstr "Ist es wirklich PLA Filament?"

# MSG_PLA_FILAMENT_LOADED c=20 r=2
#: ultralcd.cpp:4325
msgid "Is PLA filament loaded?"
msgstr "Ist PLA Filament geladen?"

# MSG_STEEL_SHEET_CHECK c=20 r=2
#: messages.c:95
msgid "Is steel sheet on heatbed?"
msgstr "Liegt das Stahlblech auf dem Heizbett?"

# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
#: mesh_bed_calibration.cpp:2223
#, fuzzy
msgid "Iteration "
msgstr ""

# MSG_KILLED
#: Marlin_main.cpp:7479
msgid "KILLED. "
msgstr "ABGEBROCHEN. "

# MSG_SELFTEST_EXTRUDER_FAN c=20
#: messages.c:81
msgid "Left hotend fan?"
msgstr "Linker Luefter?"

# 
#: ultralcd.cpp:2645
#, fuzzy
msgid "Left"
msgstr ""

# MSG_BED_CORRECTION_LEFT c=14 r=1
#: ultralcd.cpp:2885
msgid "Left side [um]"
msgstr "Links [um]"

# 
#: ultralcd.cpp:4816
#, fuzzy
msgid "Lin. correction"
msgstr ""

# MSG_BABYSTEP_Z
#: messages.c:13
msgid "Live adjust Z"
msgstr "Z einstellen"

# MSG_LOAD_FILAMENT c=17
#: messages.c:56
msgid "Load filament"
msgstr "Filament laden"

# MSG_LOADING_COLOR
#: ultralcd.cpp:2274
msgid "Loading color"
msgstr "Lade Farbe"

# MSG_LOADING_FILAMENT c=20
#: messages.c:57
msgid "Loading filament"
msgstr "Filament laedt"

# MSG_LOOSE_PULLEY c=20 r=1
#: ultralcd.cpp:6783
msgid "Loose pulley"
msgstr "Lose Riemenscheibe"

# MSG_M104_INVALID_EXTRUDER
#: Marlin_main.cpp:7602
msgid "M104 Invalid extruder "
msgstr "M104 Falscher Extruder "

# MSG_M105_INVALID_EXTRUDER
#: Marlin_main.cpp:7605
msgid "M105 Invalid extruder "
msgstr "M105 Falscher Extruder "

# MSG_M109_INVALID_EXTRUDER
#: Marlin_main.cpp:7608
msgid "M109 Invalid extruder "
msgstr "M109 Falscher Extruder "

# MSG_M117_V2_CALIBRATION c=25 r=1
#: messages.c:58
msgid "M117 First layer cal."
msgstr "M117 Erste-Schicht Kal."

# MSG_M200_INVALID_EXTRUDER
#: Marlin_main.cpp:5814
msgid "M200 Invalid extruder "
msgstr "M200 Falscher Extruder "

# MSG_M218_INVALID_EXTRUDER
#: Marlin_main.cpp:7611
msgid "M218 Invalid extruder "
msgstr "M218 Falscher Extruder "

# MSG_M221_INVALID_EXTRUDER
#: Marlin_main.cpp:7614
msgid "M221 Invalid extruder "
msgstr "M221 Falscher Extruder "

# MSG_MAIN
#: messages.c:59
msgid "Main"
msgstr "Hauptmenue"

# MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
#: messages.c:60
msgid "Measuring reference height of calibration point"
msgstr "Messen der Referenzhoehe des Kalibrierpunktes"

# MSG_MESH_BED_LEVELING
#: ultralcd.cpp:4901
msgid "Mesh Bed Leveling"
msgstr "Mesh Bett Ausglei."

# MSG_MMU_NEEDS_ATTENTION c=20 r=4
#: mmu.cpp:414
msgid "MMU needs user attention. Fix the issue and then press button on MMU unit."
msgstr "MMU hat eine Stoerung. Beseitigen Sie das Problem und druecken Sie den Knopf an der MMU."

# MSG_MMU_OK_RESUMING_POSITION c=20 r=4
#: mmu.cpp:433
msgid "MMU OK. Resuming position..."
msgstr "MMU OK. Position wiederherstellen..."

# MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
#: mmu.cpp:423
msgid "MMU OK. Resuming temperature..."
msgstr "MMU OK. Temperatur wiederherstellen..."

# 
#: ultralcd.cpp:2680
#, fuzzy
msgid "Measured skew"
msgstr ""

# MSG_MMU_OK_RESUMING c=20 r=4
#: mmu.cpp:444
msgid "MMU OK. Resuming..."
msgstr "MMU OK.  Weiterdrucken..."

# MSG_STEALTH_MODE_OFF
#: messages.c:93
msgid "Mode     [Normal]"
msgstr "Modus    [Normal]"

# MSG_SILENT_MODE_ON
#: messages.c:92
msgid "Mode     [silent]"
msgstr "Modus     [leise]"

# MSG_STEALTH_MODE_ON
#: messages.c:94
msgid "Mode    [Stealth]"
msgstr "Modus   [Stealth]"

# MSG_AUTO_MODE_ON
#: messages.c:12
msgid "Mode [auto power]"
msgstr "Modus[Auto Power]"

# MSG_SILENT_MODE_OFF
#: messages.c:91
msgid "Mode [high power]"
msgstr "Modus[Hohe Leist]"

# MSG_SELFTEST_MOTOR
#: messages.c:88
#, fuzzy
msgid "Motor"
msgstr ""

# MSG_MOVE_AXIS
#: ultralcd.cpp:4796
msgid "Move axis"
msgstr "Achse bewegen"

# MSG_MOVE_X
#: ultralcd.cpp:3922
msgid "Move X"
msgstr "Bewege X"

# MSG_MOVE_Y
#: ultralcd.cpp:3923
msgid "Move Y"
msgstr "Bewege Y"

# MSG_MOVE_Z
#: ultralcd.cpp:3924
msgid "Move Z"
msgstr "Bewege Z"

# MSG_ERR_NO_CHECKSUM
#: cmdqueue.cpp:456
msgid "No Checksum with line number, Last Line: "
msgstr "Keine Pruefsumme mit Zeilennummer, Letzte Zeile: "

# MSG_NO_MOVE
#: Marlin_main.cpp:4812
msgid "No move."
msgstr "Keine Bewegung."

# MSG_NO_CARD
#: ultralcd.cpp:5749
msgid "No SD card"
msgstr "Keine SD Karte"

# MSG_NO
#: messages.c:63
msgid "No"
msgstr "Nein"

# MSG_SELFTEST_NOTCONNECTED
#: ultralcd.cpp:6731
msgid "Not connected"
msgstr "Nicht angeschlossen"

# 
#: util.cpp:293
#, fuzzy
msgid "New firmware version available:"
msgstr ""

# MSG_SELFTEST_FAN_NO c=19
#: messages.c:84
msgid "Not spinning"
msgstr "Dreht sich nicht"

# MSG_WIZARD_V2_CAL c=20 r=8
#: ultralcd.cpp:4554
msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
msgstr "Jetzt werde ich den Abstand zwischen Duesenspitze und Druckbett kalibrieren."

# MSG_WIZARD_WILL_PREHEAT c=20 r=4
#: ultralcd.cpp:4500
msgid "Now I will preheat nozzle for PLA."
msgstr "Jetzt werde ich die Duese fuer PLA vorheizen."

# MSG_NOZZLE
#: messages.c:64
msgid "Nozzle"
msgstr "Duese"

# MSG_OK
#: Marlin_main.cpp:6290
#, fuzzy
msgid "ok"
msgstr ""

# MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
#: Marlin_main.cpp:1485
msgid "Old settings found. Default PID, Esteps etc. will be set."
msgstr "Alte Einstellungen gefunden. Standard PID, E-Steps u.s.w. werden gesetzt."

# MSG_SD_OPEN_FILE_FAIL
#: messages.c:79
msgid "open failed, File: "
msgstr "Fehler beim Oeffnen der Datei: "

# MSG_ENDSTOP_OPEN
#: messages.c:29
msgid "open"
msgstr "offen"

# MSG_SD_OPENROOT_FAIL
#: cardreader.cpp:196
msgid "openRoot failed"
msgstr "Zugriff auf Hauptverzeichnis misslungen"

# MSG_PAUSE_PRINT
#: ultralcd.cpp:5723
msgid "Pause print"
msgstr "Druck pausieren"

# MSG_PID_RUNNING c=20 r=1
#: ultralcd.cpp:1704
msgid "PID cal.           "
msgstr "PID Kal.           "

# MSG_PID_FINISHED c=20 r=1
#: ultralcd.cpp:1710
msgid "PID cal. finished"
msgstr "PID Kalib. fertig"

# MSG_PID_EXTRUDER c=17 r=1
#: ultralcd.cpp:4907
msgid "PID calibration"
msgstr "PID Kalibrierung"

# MSG_PINDA_PREHEAT c=20 r=1
#: ultralcd.cpp:768
msgid "PINDA Heating"
msgstr "PINDA erwaermen"

# MSG_PAPER c=20 r=8
#: messages.c:66
msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
msgstr "Legen Sie ein Blatt Papier unter die Duese waehrend der Kalibrierung der ersten 4 Punkte. Wenn die Duese das Papier erfasst, den Drucker sofort ausschalten."

# MSG_WIZARD_CLEAN_HEATBED c=20 r=8
#: ultralcd.cpp:4563
msgid "Please clean heatbed and then press the knob."
msgstr "Bitte reinigen Sie das Heizbett und druecken Sie dann den Knopf."

# MSG_CONFIRM_NOZZLE_CLEAN c=20 r=8
#: messages.c:22
msgid "Please clean the nozzle for calibration. Click when done."
msgstr "Bitte entfernen Sie ueberstehendes Filament von der Duese. Klicken wenn sauber."

# MSG_SELFTEST_PLEASECHECK
#: ultralcd.cpp:6723
msgid "Please check :"
msgstr "Bitte pruefe:"

# MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
#: messages.c:103
msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
msgstr "Bitte lesen Sie unser Handbuch und beheben Sie das Problem. Fahren Sie dann mit dem Assistenten fort, indem Sie den Drucker neu starten."

# MSG_WIZARD_LOAD_FILAMENT c=20 r=8
#: ultralcd.cpp:4536
msgid "Please insert PLA filament to the extruder, then press knob to load it."
msgstr "Legen Sie bitte PLA Filament in den Extruder und druecken Sie den Knopf,  um es zu laden."

# MSG_WIZARD_INSERT_CORRECT_FILAMENT c=20 r=8
#: 
msgid "Please load PLA filament and then resume Wizard by rebooting the printer."
msgstr "Bitte PLA-Filament laden und Assistent fortsetzen, indem Sie den Drucker neu starten."

# MSG_PLEASE_LOAD_PLA c=20 r=4
#: ultralcd.cpp:4330
msgid "Please load PLA filament first."
msgstr "Bitte laden Sie zuerst PLA Filament."

# MSG_CHECK_IDLER c=20 r=4
#: Marlin_main.cpp:2959
msgid "Please open idler and remove filament manually."
msgstr "Bitte Spannrolle oeffnen und Fila- ment von Hand entfernen"

# MSG_PLACE_STEEL_SHEET c=20 r=4
#: messages.c:67
msgid "Please place steel sheet on heatbed."
msgstr "Bitte legen Sie das Stahlblech auf das Heizbett."

# MSG_PRESS_TO_UNLOAD c=20 r=4
#: messages.c:71
msgid "Please press the knob to unload filament"
msgstr "Bitte druecken Sie den Knopf um das  Filament zu entladen."

# 
#: ultralcd.cpp:4533
#, fuzzy
msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
msgstr ""

# MSG_PULL_OUT_FILAMENT c=20 r=4
#: messages.c:73
msgid "Please pull out filament immediately"
msgstr "Bitte ziehen Sie das Filament sofort heraus"

# MSG_EJECT_REMOVE c=20 r=4
#: mmu.cpp:1052
msgid "Please remove filament and then press the knob."
msgstr "Bitte Filament entfernen und dann den Knopf druecken."

# MSG_REMOVE_STEEL_SHEET c=20 r=4
#: messages.c:77
msgid "Please remove steel sheet from heatbed."
msgstr "Bitte entfernen Sie das Stahlblech vom Heizbett."

# MSG_RUN_XYZ c=20 r=4
#: Marlin_main.cpp:3989
msgid "Please run XYZ calibration first."
msgstr "Bitte zuerst XYZ Kalibrierung ausfuehren."

# MSG_UPDATE_MMU2_FW c=20 r=4
#: mmu.cpp:1029
msgid "Please update firmware in your MMU2. Waiting for reset."
msgstr "Bitte aktualisieren Sie die Firmware in der MMU2. Warte auf Reset."

# MSG_PLEASE_WAIT c=20
#: messages.c:68
msgid "Please wait"
msgstr "Bitte warten"

# MSG_POWERUP
#: messages.c:69
msgid "PowerUp"
msgstr "Einschalten"

# MSG_PREHEAT_NOZZLE c=20
#: messages.c:70
msgid "Preheat the nozzle!"
msgstr "Duese vorheizen!"

# MSG_PREHEAT
#: ultralcd.cpp:5712
msgid "Preheat"
msgstr "Vorheizen"

# MSG_WIZARD_HEATING c=20 r=3
#: messages.c:105
msgid "Preheating nozzle. Please wait."
msgstr "Vorheizen der Duese. Bitte warten."

# 
#: util.cpp:297
#, fuzzy
msgid "Please upgrade."
msgstr ""

# MSG_PRESS_TO_PREHEAT c=20 r=4
#: Marlin_main.cpp:8970
msgid "Press knob to preheat nozzle and continue."
msgstr "Bitte druecken Sie den Knopf um die  Duese vorzuheizen und fortzufahren."

# MSG_PRINT_ABORTED c=20
#: messages.c:72
msgid "Print aborted"
msgstr "Druck abgebrochen"

# MSG_SELFTEST_PRINT_FAN_SPEED c=18
#: ultralcd.cpp:7030
msgid "Print fan:"
msgstr "Druckvent.:"

# MSG_CARD_MENU
#: messages.c:21
msgid "Print from SD"
msgstr "Drucken von SD"

# MSG_PRINT_PAUSED c=20 r=1
#: ultralcd.cpp:982
msgid "Print paused"
msgstr "Druck pausiert"

# MSG_ERR_KILLED
#: Marlin_main.cpp:7474
msgid "Printer halted. kill() called!"
msgstr "Printer gestoppt. kill() aufgerufen!"

# MSG_FOLLOW_CALIBRATION_FLOW c=20 r=8
#: messages.c:46
msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
msgstr "Drucker wurde noch  nicht kalibriert. Bitte folgen Sie dem Handbuch, Kapitel Erste Schritte, Abschnitt Kalibrie- rungsablauf."

# MSG_ERR_STOPPED
#: messages.c:32
msgid "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
msgstr "Drucker aufgrund von Fehlern gestoppt. Fehler beheben und mit M999 neu starten. (Temperatur wird zurueckgesetzt. Nach dem Neustart neu einstellen!)"

# WELCOME_MSG c=20
#: 
msgid "Prusa i3 MK2.5 ready."
msgstr "Prusa i3 MK2.5 bereit"

# WELCOME_MSG c=20
#: 
msgid "Prusa i3 MK3 ready."
msgstr "Prusa i3 MK3 bereit."

# MSG_PRUSA3D
#: ultralcd.cpp:2142
#, fuzzy
msgid "prusa3d.com"
msgstr ""

# MSG_BED_CORRECTION_REAR c=14 r=1
#: ultralcd.cpp:2888
msgid "Rear side [um]"
msgstr "Hinten [um]"

# MSG_RECOVERING_PRINT c=20 r=1
#: Marlin_main.cpp:8404
msgid "Recovering print    "
msgstr "Druck wiederherst    "

# MSG_REMOVE_OLD_FILAMENT c=20 r=4
#: mmu.cpp:489
msgid "Remove old filament and press the knob to start loading new filament."
msgstr "Entfernen Sie das alte Filament und druecken Sie den Knopf, um das neue zu laden."

# MSG_CALIBRATE_BED_RESET
#: ultralcd.cpp:4914
msgid "Reset XYZ calibr."
msgstr "XYZ Kalib.zurueck"

# MSG_BED_CORRECTION_RESET
#: ultralcd.cpp:2889
msgid "Reset"
msgstr "Ruecksetzen"

# MSG_RESUME_PRINT
#: ultralcd.cpp:5727
msgid "Resume print"
msgstr "Druck fortsetzen"

# MSG_RESUMING_PRINT c=20 r=1
#: messages.c:76
msgid "Resuming print"
msgstr "Druck fortgesetzt"

# MSG_BED_CORRECTION_RIGHT c=14 r=1
#: ultralcd.cpp:2886
msgid "Right side[um]"
msgstr "Rechts [um]"

# MSG_SECOND_SERIAL_ON c=17 r=1
#: ultralcd.cpp:4828
msgid "RPi port     [on]"
msgstr "RPi Port     [an]"

# 
#: Marlin_main.cpp:6997
#, fuzzy
msgid "Resend"
msgstr ""

# MSG_SECOND_SERIAL_OFF c=17 r=1
#: ultralcd.cpp:4826
msgid "RPi port    [off]"
msgstr "RPi Port    [aus]"

# MSG_WIZARD_RERUN c=20 r=7
#: ultralcd.cpp:4346
msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
msgstr "Der Assistent wird die aktuellen Kalibrierungsdaten loeschen und von vorne beginnen. Weiterfahren?"

# MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
#: ultralcd.cpp:4732
msgid "SD card  [normal]"
msgstr "SD Karte [normal]"

# MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
#: 
msgid "SD card [FlshAir]"
msgstr "SD Kart.[FlshAir]"

# MSG_SD_CARD_OK
#: cardreader.cpp:202
msgid "SD card ok"
msgstr "SD Karte ok"

# 
#: ultralcd.cpp:2646
#, fuzzy
msgid "Right"
msgstr ""

# MSG_SD_INIT_FAIL
#: cardreader.cpp:186
msgid "SD init fail"
msgstr "SD Init fehlerhaft"

# MSG_FIND_BED_OFFSET_AND_SKEW_LINE1 c=60
#: messages.c:43
msgid "Searching bed calibration point"
msgstr "Suche Bett Kalibrierpunkt"

# MSG_LANGUAGE_SELECT
#: ultralcd.cpp:4835
msgid "Select language"
msgstr "Waehle Sprache"

# MSG_SELFTEST_OK
#: ultralcd.cpp:6295
msgid "Self test OK"
msgstr "Selbsttest OK"

# MSG_SELFTEST_START c=20
#: ultralcd.cpp:6128
msgid "Self test start  "
msgstr "Selbsttest start "

# MSG_SELFTEST
#: ultralcd.cpp:4888
msgid "Selftest         "
msgstr "Selbsttest "

# MSG_SELFTEST_ERROR
#: ultralcd.cpp:6721
msgid "Selftest error !"
msgstr "Selbsttest Fehler!"

# MSG_SELFTEST_FAILED c=20
#: messages.c:82
msgid "Selftest failed  "
msgstr "Selbsttest misslung  "

# MSG_FORCE_SELFTEST c=20 r=8
#: Marlin_main.cpp:1517
msgid "Selftest will be run to calibrate accurate sensorless rehoming."
msgstr "Selbsttest im Gang, um die genaue Rueck- kehr zum Nullpunkt ohne Sensor zu kalibrieren"

# 
#: ultralcd.cpp:4507
#, fuzzy
msgid "Select nozzle preheat temperature which matches your material."
msgstr ""

# 
#: ultralcd.cpp:4316
#, fuzzy
msgid "Select PLA filament:"
msgstr ""

# MSG_SET_TEMPERATURE c=19 r=1
#: ultralcd.cpp:2897
msgid "Set temperature:"
msgstr "Temp. einstellen:"

# MSG_SETTINGS
#: messages.c:90
msgid "Settings"
msgstr "Einstellungen"

# MSG_SHOW_END_STOPS c=17 r=1
#: ultralcd.cpp:4911
msgid "Show end stops"
msgstr "Endschalter Status"

# 
#: ultralcd.cpp:4909
#, fuzzy
msgid "Show pinda state"
msgstr ""

# MSG_DWELL
#: Marlin_main.cpp:3730
msgid "Sleep..."
msgstr "Schlafzustand..."

# MSG_FILE_CNT c=20 r=4
#: cardreader.cpp:738
msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
msgstr "Einige Dateien wur- den nicht sortiert. Max. Dateien pro Verzeichnis = 100."

# MSG_SORT_NONE c=17 r=1
#: ultralcd.cpp:4742
msgid "Sort:      [none]"
msgstr "Sort.:    [Keine]"

# MSG_SORT_TIME c=17 r=1
#: ultralcd.cpp:4740
msgid "Sort:      [time]"
msgstr "Sort.:     [Zeit]"

# 
#: ultralcd.cpp:2683
#, fuzzy
msgid "Severe skew"
msgstr ""

# MSG_SORT_ALPHA c=17 r=1
#: ultralcd.cpp:4741
msgid "Sort:  [alphabet]"
msgstr "Sort.: [Alphabet]"

# MSG_SORTING c=20 r=1
#: cardreader.cpp:745
msgid "Sorting files"
msgstr "Sortiere Dateien"

# MSG_SOUND_LOUD c=17 r=1
#: sound.h:5
msgid "Sound      [loud]"
msgstr "Sound      [laut]"

# 
#: ultralcd.cpp:2682
#, fuzzy
msgid "Slight skew"
msgstr ""

# MSG_SOUND_MUTE c=17 r=1
#: sound.h:8
msgid "Sound      [mute]"
msgstr "Sound     [stumm]"

# MSG_SOUND_ONCE c=17 r=1
#: sound.h:6
msgid "Sound      [once]"
msgstr "Sound    [einmal]"

# MSG_SOUND_SILENT c=17 r=1
#: sound.h:7
msgid "Sound    [silent]"
msgstr "Sound     [leise]"

# MSG_SPEED
#: ultralcd.cpp:5884
msgid "Speed"
msgstr "Geschwindigkeit"

# MSG_SELFTEST_FAN_YES c=19
#: messages.c:85
msgid "Spinning"
msgstr "Dreht sich"

# MSG_TEMP_CAL_WARNING c=20 r=4
#: Marlin_main.cpp:4002
msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
msgstr "Stabile Umgebungs- temperatur 21-26C und feste Stand- flaeche erforderlich"

# MSG_STATISTICS
#: ultralcd.cpp:5795
msgid "Statistics  "
msgstr "Statistiken "

# MSG_STOP_PRINT
#: messages.c:96
msgid "Stop print"
msgstr "Druck abbrechen"

# MSG_STOPPED
#: messages.c:97
msgid "STOPPED. "
msgstr "GESTOPPT. "

# MSG_SUPPORT
#: ultralcd.cpp:5802
#, fuzzy
msgid "Support"
msgstr ""

# MSG_SELFTEST_SWAPPED
#: ultralcd.cpp:6801
msgid "Swapped"
msgstr "Ausgetauscht"

# MSG_TEMP_CALIBRATION c=20 r=1
#: messages.c:98
msgid "Temp. cal.          "
msgstr "Temp Kalib. "

# MSG_TEMP_CALIBRATION_ON c=20 r=1
#: ultralcd.cpp:4822
msgid "Temp. cal.   [on]"
msgstr "Temp. Kal.   [AN]"

# MSG_TEMP_CALIBRATION_OFF c=20 r=1
#: ultralcd.cpp:4820
msgid "Temp. cal.  [off]"
msgstr "Temp. Kal.  [AUS]"

# MSG_CALIBRATION_PINDA_MENU c=17 r=1
#: ultralcd.cpp:4920
msgid "Temp. calibration"
msgstr "Temp. kalibrieren"

# MSG_TEMP_CAL_FAILED c=20 r=8
#: ultralcd.cpp:3535
msgid "Temperature calibration failed"
msgstr "Temperaturkalibrierung fehlgeschlagen"

# MSG_TEMP_CALIBRATION_DONE c=20 r=12
#: messages.c:99
msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
msgstr "Temp.kalibrierung ist fertig + aktiv. Temp.kalibrierung kann ausgeschaltet werden im Menu Einstellungen -> Temp.kal."

# MSG_TEMPERATURE
#: ultralcd.cpp:4794
msgid "Temperature"
msgstr "Temperatur"

# MSG_MENU_TEMPERATURES c=15 r=1
#: ultralcd.cpp:2187
msgid "Temperatures"
msgstr "Temperaturen"

# MSG_FOLLOW_Z_CALIBRATION_FLOW c=20 r=4
#: messages.c:47
msgid "There is still a need to make Z calibration. Please follow the manual, chapter First steps, section Calibration flow."
msgstr "Es ist noch notwendig die Z-Kalibrierung auszufuehren. Bitte befolgen Sie das Handbuch, Kapitel Erste Schritte, Abschnitt Kalibrierablauf."

# 
#: ultralcd.cpp:2531
#, fuzzy
msgid "Total filament"
msgstr ""

# 
#: ultralcd.cpp:2533
#, fuzzy
msgid "Total print time"
msgstr ""

# MSG_ENDSTOP_HIT
#: messages.c:28
msgid "TRIGGERED"
msgstr "AUSGELOEST"

# MSG_TUNE
#: ultralcd.cpp:5709
msgid "Tune"
msgstr "Feineinstellung"

# 
#: ultralcd.cpp:4516
#, fuzzy
msgid "Unload"
msgstr ""

# 
#: ultralcd.cpp:5313
#, fuzzy
msgid "Unload all"
msgstr ""

# MSG_UNLOAD_FILAMENT c=17
#: messages.c:100
msgid "Unload filament"
msgstr "Filament entladen"

# MSG_UNLOADING_FILAMENT c=20 r=1
#: messages.c:101
msgid "Unloading filament"
msgstr "Filament auswerfen"

# MSG_USED c=19 r=1
#: ultralcd.cpp:5045
msgid "Used during print"
msgstr "Beim Druck benutzt"

# MSG_MENU_VOLTAGES c=15 r=1
#: ultralcd.cpp:2190
msgid "Voltages"
msgstr "Spannungen"

# MSG_SD_VOL_INIT_FAIL
#: cardreader.cpp:191
msgid "volume.init failed"
msgstr "Dateisystem Init fehlerhaft"

# MSG_USERWAIT
#: Marlin_main.cpp:4780
msgid "Wait for user..."
msgstr "Warte auf Benutzer.."

# MSG_WAITING_TEMP c=20 r=3
#: ultralcd.cpp:3041
msgid "Waiting for nozzle and bed cooling"
msgstr "Warten bis Heizung und Bett abgekuehlt sind"

# MSG_WAITING_TEMP_PINDA c=20 r=3
#: ultralcd.cpp:3005
msgid "Waiting for PINDA probe cooling"
msgstr "Warten, bis PINDA- Sonde abgekuehlt ist"

# MSG_CHANGED_BOTH c=20 r=4
#: Marlin_main.cpp:1477
msgid "Warning: both printer type and motherboard type changed."
msgstr "Warnung: Druckertyp und Platinentyp wurden beide geaendert."

# MSG_CHANGED_MOTHERBOARD c=20 r=4
#: Marlin_main.cpp:1469
msgid "Warning: motherboard type changed."
msgstr "Warnung: Platinentyp wurde geaendert."

# MSG_CHANGED_PRINTER c=20 r=4
#: Marlin_main.cpp:1473
msgid "Warning: printer type changed."
msgstr "Warnung: Druckertyp wurde geaendert."

# MSG_UNLOAD_SUCCESSFUL c=20 r=2
#: Marlin_main.cpp:2956
msgid "Was filament unload successful?"
msgstr "Konnten Sie das Filament entnehmen?"

# MSG_SELFTEST_WIRINGERROR
#: messages.c:89
msgid "Wiring error"
msgstr "Verdrahtungsfehler"

# MSG_WIZARD c=17 r=1
#: ultralcd.cpp:4885
msgid "Wizard"
msgstr "Assistent"

# MSG_XYZ_DETAILS c=19 r=1
#: ultralcd.cpp:2180
msgid "XYZ cal. details"
msgstr "XYZ Kal. Details"

# MSG_BED_SKEW_OFFSET_DETECTION_FITTING_FAILED c=20 r=8
#: messages.c:19
msgid "XYZ calibration failed. Please consult the manual."
msgstr "XYZ-Kalibrierung fehlgeschlagen. Bitte schauen Sie in das Handbuch."

# MSG_YES
#: messages.c:107
msgid "Yes"
msgstr "Ja"

# MSG_WIZARD_QUIT c=20 r=8
#: messages.c:106
msgid "You can always resume the Wizard from Calibration -> Wizard."
msgstr "Sie koennen den Assistenten immer im Menu neu starten: Kalibrierung -> Assistent"

# MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
#: ultralcd.cpp:3506
msgid "XYZ calibration all right. Skew will be corrected automatically."
msgstr "XYZ Kalibrierung in Ordnung. Schiefheit wird automatisch korrigiert."

# MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
#: ultralcd.cpp:3503
msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
msgstr "XYZ Kalibrierung in Ordnung. X/Y Achsen sind etwas schief."

# MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
#: ultralcd.cpp:3500
msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
msgstr "XYZ-Kalibrierung OK. X/Y-Achsen sind senkrecht zueinander. Glueckwunsch!"

# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
#: ultralcd.cpp:3484
msgid "XYZ calibration compromised. Front calibration points not reachable."
msgstr "XYZ-Kalibrierung ungenau. Vordere Kalibrierpunkte sind zu weit vorne."

# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
#: ultralcd.cpp:3487
msgid "XYZ calibration compromised. Right front calibration point not reachable."
msgstr "XYZ-Kalibrierung ungenau. Rechter vorderer Kalibrierpunkt ist zu weit vorne."

# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
#: ultralcd.cpp:3490
msgid "XYZ calibration compromised. Left front calibration point not reachable."
msgstr "XYZ-Kalibrierung ungenau. Linker vorderer Kalibrierpunkt ist zu weit vorne."

# MSG_LOAD_ALL c=17
#: ultralcd.cpp:5284
msgid "Load all"
msgstr "Alle laden"

# MSG_LOAD_FILAMENT_1 c=17
#: ultralcd.cpp:5285
msgid "Load filament 1"
msgstr "Filament 1 laden"

# MSG_LOAD_FILAMENT_2 c=17
#: ultralcd.cpp:5286
msgid "Load filament 2"
msgstr "Filament 2 laden"

# MSG_LOAD_FILAMENT_3 c=17
#: ultralcd.cpp:5287
msgid "Load filament 3"
msgstr "Filament 3 laden"

# MSG_LOAD_FILAMENT_4 c=17
#: ultralcd.cpp:5288
msgid "Load filament 4"
msgstr "Filament 4 laden"

# MSG_LOAD_FILAMENT_5 c=17
#: ultralcd.cpp:5291
msgid "Load filament 5"
msgstr "Filament 5 laden"