eeprom.h 12 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204
  1. #ifndef EEPROM_H
  2. #define EEPROM_H
  3. // The total size of the EEPROM is
  4. // 4096 for the Atmega2560
  5. #define EEPROM_TOP 4096
  6. #define EEPROM_SILENT 4095
  7. #define EEPROM_LANG 4094
  8. #define EEPROM_BABYSTEP_X 4092
  9. #define EEPROM_BABYSTEP_Y 4090
  10. #define EEPROM_BABYSTEP_Z 4088
  11. #define EEPROM_CALIBRATION_STATUS 4087
  12. #define EEPROM_BABYSTEP_Z0 4085
  13. #define EEPROM_FILAMENTUSED 4081
  14. // uint32_t
  15. #define EEPROM_TOTALTIME 4077
  16. #define EEPROM_BED_CALIBRATION_CENTER (EEPROM_TOTALTIME-2*4)
  17. #define EEPROM_BED_CALIBRATION_VEC_X (EEPROM_BED_CALIBRATION_CENTER-2*4)
  18. #define EEPROM_BED_CALIBRATION_VEC_Y (EEPROM_BED_CALIBRATION_VEC_X-2*4)
  19. // Offsets of the Z heiths of the calibration points from the first point.
  20. // The offsets are saved as 16bit signed int, scaled to tenths of microns.
  21. #define EEPROM_BED_CALIBRATION_Z_JITTER (EEPROM_BED_CALIBRATION_VEC_Y-2*8)
  22. #define EEPROM_FARM_MODE (EEPROM_BED_CALIBRATION_Z_JITTER-1)
  23. #define EEPROM_FARM_NUMBER (EEPROM_FARM_MODE-3)
  24. // Correction of the bed leveling, in micrometers.
  25. // Maximum 50 micrometers allowed.
  26. // Bed correction is valid if set to 1. If set to zero or 255, the successive 4 bytes are invalid.
  27. #define EEPROM_BED_CORRECTION_VALID (EEPROM_FARM_NUMBER-1)
  28. #define EEPROM_BED_CORRECTION_LEFT (EEPROM_BED_CORRECTION_VALID-1)
  29. #define EEPROM_BED_CORRECTION_RIGHT (EEPROM_BED_CORRECTION_LEFT-1)
  30. #define EEPROM_BED_CORRECTION_FRONT (EEPROM_BED_CORRECTION_RIGHT-1)
  31. #define EEPROM_BED_CORRECTION_REAR (EEPROM_BED_CORRECTION_FRONT-1)
  32. #define EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY (EEPROM_BED_CORRECTION_REAR-1)
  33. #define EEPROM_PRINT_FLAG (EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY-1)
  34. #define EEPROM_PROBE_TEMP_SHIFT (EEPROM_PRINT_FLAG - 2*5) //5 x int for storing pinda probe temp shift relative to 50 C; unit: motor steps
  35. #define EEPROM_TEMP_CAL_ACTIVE (EEPROM_PROBE_TEMP_SHIFT - 1)
  36. #define EEPROM_BOWDEN_LENGTH (EEPROM_TEMP_CAL_ACTIVE - 2*4) //4 x int for bowden lengths for multimaterial
  37. #define EEPROM_CALIBRATION_STATUS_PINDA (EEPROM_BOWDEN_LENGTH - 1) //0 - not calibrated; 1 - calibrated
  38. #define EEPROM_UVLO (EEPROM_CALIBRATION_STATUS_PINDA - 1) //1 - uvlo during print
  39. #define EEPROM_UVLO_CURRENT_POSITION (EEPROM_UVLO-2*4) // 2 x float for current_position in X and Y axes
  40. #define EEPROM_FILENAME (EEPROM_UVLO_CURRENT_POSITION - 8) //8chars to store filename without extension
  41. #define EEPROM_FILE_POSITION (EEPROM_FILENAME - 4) //32 bit for uint32_t file position
  42. #define EEPROM_UVLO_CURRENT_POSITION_Z (EEPROM_FILE_POSITION - 4) //float for current position in Z
  43. #define EEPROM_UVLO_TARGET_HOTEND (EEPROM_UVLO_CURRENT_POSITION_Z - 1)
  44. #define EEPROM_UVLO_TARGET_BED (EEPROM_UVLO_TARGET_HOTEND - 1)
  45. #define EEPROM_UVLO_FEEDRATE (EEPROM_UVLO_TARGET_BED - 2)
  46. #define EEPROM_UVLO_FAN_SPEED (EEPROM_UVLO_FEEDRATE - 1)
  47. #define EEPROM_FAN_CHECK_ENABLED (EEPROM_UVLO_FAN_SPEED - 1)
  48. #define EEPROM_UVLO_MESH_BED_LEVELING (EEPROM_FAN_CHECK_ENABLED - 9*2)
  49. #define EEPROM_UVLO_Z_MICROSTEPS (EEPROM_UVLO_MESH_BED_LEVELING - 2)
  50. #define EEPROM_UVLO_E_ABS (EEPROM_UVLO_Z_MICROSTEPS - 1)
  51. #define EEPROM_UVLO_CURRENT_POSITION_E (EEPROM_UVLO_E_ABS - 4) //float for current position in E
  52. // Crash detection mode EEPROM setting
  53. #define EEPROM_CRASH_DET (EEPROM_UVLO_CURRENT_POSITION_E - 5) // float (orig EEPROM_UVLO_MESH_BED_LEVELING-12)
  54. // Crash detection counter Y (last print)
  55. #define EEPROM_CRASH_COUNT_Y (EEPROM_CRASH_DET - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-15)
  56. // Filament sensor on/off EEPROM setting
  57. #define EEPROM_FSENSOR (EEPROM_CRASH_COUNT_Y - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-14)
  58. // Crash detection counter X (last print)
  59. #define EEPROM_CRASH_COUNT_X (EEPROM_FSENSOR - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-15)
  60. // Filament runout/error coutner (last print)
  61. #define EEPROM_FERROR_COUNT (EEPROM_CRASH_COUNT_X - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-16)
  62. // Power loss errors (last print)
  63. #define EEPROM_POWER_COUNT (EEPROM_FERROR_COUNT - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-17)
  64. #define EEPROM_XYZ_CAL_SKEW (EEPROM_POWER_COUNT - 4) // float for skew backup
  65. #define EEPROM_WIZARD_ACTIVE (EEPROM_XYZ_CAL_SKEW - 1)
  66. #define EEPROM_BELTSTATUS_X (EEPROM_WIZARD_ACTIVE - 2) // uint16
  67. #define EEPROM_BELTSTATUS_Y (EEPROM_BELTSTATUS_X - 2) // uint16
  68. #define EEPROM_DIR_DEPTH (EEPROM_BELTSTATUS_Y-1)
  69. #define EEPROM_DIRS (EEPROM_DIR_DEPTH-80) //8 chars for each dir name, max 10 levels
  70. #define EEPROM_SD_SORT (EEPROM_DIRS - 1) //0 -time, 1-alpha, 2-none
  71. #define EEPROM_SECOND_SERIAL_ACTIVE (EEPROM_SD_SORT - 1)
  72. #define EEPROM_FSENS_AUTOLOAD_ENABLED (EEPROM_SECOND_SERIAL_ACTIVE - 1)
  73. // Crash detection counter X (total)
  74. #define EEPROM_CRASH_COUNT_X_TOT (EEPROM_FSENS_AUTOLOAD_ENABLED - 2) // uint16
  75. // Crash detection counter Y (total)
  76. #define EEPROM_CRASH_COUNT_Y_TOT (EEPROM_CRASH_COUNT_X_TOT - 2) // uint16
  77. // Filament runout/error coutner (total)
  78. #define EEPROM_FERROR_COUNT_TOT (EEPROM_CRASH_COUNT_Y_TOT - 2) // uint16
  79. // Power loss errors (total)
  80. #define EEPROM_POWER_COUNT_TOT (EEPROM_FERROR_COUNT_TOT - 2) // uint16
  81. ////////////////////////////////////////
  82. // TMC2130 Accurate sensorless homing
  83. // X-axis home origin (stepper phase in microsteps, 0..63 for 16ustep resolution)
  84. #define EEPROM_TMC2130_HOME_X_ORIGIN (EEPROM_POWER_COUNT_TOT - 1) // uint8
  85. // X-axis home bsteps (number of microsteps backward)
  86. #define EEPROM_TMC2130_HOME_X_BSTEPS (EEPROM_TMC2130_HOME_X_ORIGIN - 1) // uint8
  87. // X-axis home fsteps (number of microsteps forward)
  88. #define EEPROM_TMC2130_HOME_X_FSTEPS (EEPROM_TMC2130_HOME_X_BSTEPS - 1) // uint8
  89. // Y-axis home origin (stepper phase in microsteps, 0..63 for 16ustep resolution)
  90. #define EEPROM_TMC2130_HOME_Y_ORIGIN (EEPROM_TMC2130_HOME_X_FSTEPS - 1) // uint8
  91. // X-axis home bsteps (number of microsteps backward)
  92. #define EEPROM_TMC2130_HOME_Y_BSTEPS (EEPROM_TMC2130_HOME_Y_ORIGIN - 1) // uint8
  93. // X-axis home fsteps (number of microsteps forward)
  94. #define EEPROM_TMC2130_HOME_Y_FSTEPS (EEPROM_TMC2130_HOME_Y_BSTEPS - 1) // uint8
  95. // Accurate homing enabled
  96. #define EEPROM_TMC2130_HOME_ENABLED (EEPROM_TMC2130_HOME_Y_FSTEPS - 1) // uint8
  97. ////////////////////////////////////////
  98. // TMC2130 uStep linearity correction
  99. // Linearity correction factor (XYZE)
  100. #define EEPROM_TMC2130_WAVE_X_FAC (EEPROM_TMC2130_HOME_ENABLED - 1) // uint8
  101. #define EEPROM_TMC2130_WAVE_Y_FAC (EEPROM_TMC2130_WAVE_X_FAC - 1) // uint8
  102. #define EEPROM_TMC2130_WAVE_Z_FAC (EEPROM_TMC2130_WAVE_Y_FAC - 1) // uint8
  103. #define EEPROM_TMC2130_WAVE_E_FAC (EEPROM_TMC2130_WAVE_Z_FAC - 1) // uint8
  104. ////////////////////////////////////////
  105. // TMC2130 uStep resolution
  106. // microstep resolution (XYZE): usteps = (256 >> mres)
  107. #define EEPROM_TMC2130_X_MRES (EEPROM_TMC2130_WAVE_E_FAC - 1) // uint8
  108. #define EEPROM_TMC2130_Y_MRES (EEPROM_TMC2130_X_MRES - 1) // uint8
  109. #define EEPROM_TMC2130_Z_MRES (EEPROM_TMC2130_Y_MRES - 1) // uint8
  110. #define EEPROM_TMC2130_E_MRES (EEPROM_TMC2130_Z_MRES - 1) // uint8
  111. // HW
  112. #define EEPROM_PRINTER_TYPE (EEPROM_TMC2130_E_MRES - 2) // uint16
  113. #define EEPROM_BOARD_TYPE (EEPROM_PRINTER_TYPE - 2) // uint16
  114. // Extruder multiplier for power panic
  115. #define EEPROM_EXTRUDER_MULTIPLIER_0 (EEPROM_BOARD_TYPE - 4) //float
  116. #define EEPROM_EXTRUDER_MULTIPLIER_1 (EEPROM_EXTRUDER_MULTIPLIER_0 - 4) //float
  117. #define EEPROM_EXTRUDER_MULTIPLIER_2 (EEPROM_EXTRUDER_MULTIPLIER_1 - 4) //float
  118. #define EEPROM_EXTRUDEMULTIPLY (EEPROM_EXTRUDER_MULTIPLIER_2 - 2) // uint16
  119. //
  120. #define EEPROM_UVLO_TINY_CURRENT_POSITION_Z (EEPROM_EXTRUDEMULTIPLY-4) // float
  121. #define EEPROM_UVLO_TINY_Z_MICROSTEPS (EEPROM_UVLO_TINY_CURRENT_POSITION_Z-2) // uint16
  122. // Sound Mode
  123. //#define EEPROM_SOUND_MODE (EEPROM_EXTRUDEMULTIPLY-1) // uint8
  124. #define EEPROM_SOUND_MODE (EEPROM_UVLO_TINY_Z_MICROSTEPS-1) // uint8
  125. #define EEPROM_AUTO_DEPLETE (EEPROM_SOUND_MODE-1) //bool
  126. #define EEPROM_FSENS_OQ_MEASS_ENABLED (EEPROM_AUTO_DEPLETE - 1) //bool
  127. #define EEPROM_MMU_FAIL_TOT (EEPROM_FSENS_OQ_MEASS_ENABLED - 2) //uint16_t
  128. #define EEPROM_MMU_FAIL (EEPROM_MMU_FAIL_TOT - 1) //uint8_t
  129. #define EEPROM_MMU_LOAD_FAIL_TOT (EEPROM_MMU_FAIL - 2) //uint16_t
  130. #define EEPROM_MMU_LOAD_FAIL (EEPROM_MMU_LOAD_FAIL_TOT - 1) //uint8_t
  131. #define EEPROM_MMU_CUTTER_ENABLED (EEPROM_MMU_LOAD_FAIL - 1)
  132. #define EEPROM_UVLO_MESH_BED_LEVELING_FULL (EEPROM_MMU_CUTTER_ENABLED - 12*12*2) //allow 12 calibration points for future expansion
  133. #define EEPROM_MBL_TYPE (EEPROM_UVLO_MESH_BED_LEVELING_FULL-1) //uint8_t for mesh bed leveling precision
  134. #define EEPROM_MBL_MAGNET_ELIMINATION (EEPROM_MBL_TYPE -1)
  135. #define EEPROM_MBL_POINTS_NR (EEPROM_MBL_MAGNET_ELIMINATION -1) //uint8_t number of points in one exis for mesh bed leveling
  136. #define EEPROM_MBL_PROBE_NR (EEPROM_MBL_POINTS_NR-1)
  137. // !!!!!
  138. // !!!!! this is end of EEPROM section ... all updates MUST BE inserted before this mark !!!!!
  139. // !!!!!
  140. //TMC2130 configuration
  141. #define EEPROM_TMC_AXIS_SIZE //axis configuration block size
  142. #define EEPROM_TMC_X (EEPROM_TMC + 0 * EEPROM_TMC_AXIS_SIZE) //X axis configuration blok
  143. #define EEPROM_TMC_Y (EEPROM_TMC + 1 * EEPROM_TMC_AXIS_SIZE) //Y axis
  144. #define EEPROM_TMC_Z (EEPROM_TMC + 2 * EEPROM_TMC_AXIS_SIZE) //Z axis
  145. #define EEPROM_TMC_E (EEPROM_TMC + 3 * EEPROM_TMC_AXIS_SIZE) //E axis
  146. //TMC2130 - X axis
  147. #define EEPROM_TMC_X_USTEPS_INTPOL (EEPROM_TMC_X + 0) // 1byte, bit 0..4 USTEPS, bit 7 INTPOL
  148. #define EEPROM_TMC_X_PWM_AMPL (EEPROM_TMC_X + 1) // 1byte (0..255)
  149. #define EEPROM_TMC_X_PWM_GRAD_FREQ (EEPROM_TMC_X + 2) // 1byte, bit 0..3 GRAD, bit 4..5 FREQ
  150. #define EEPROM_TMC_X_TCOOLTHRS (EEPROM_TMC_X + 3) // 2bytes (0..)
  151. #define EEPROM_TMC_X_SG_THRS (EEPROM_TMC_X + 5) // 1byte, (-64..+63)
  152. #define EEPROM_TMC_X_CURRENT_H (EEPROM_TMC_X + 6) // 1byte, (0..63)
  153. #define EEPROM_TMC_X_CURRENT_R (EEPROM_TMC_X + 7) // 1byte, (0..63)
  154. #define EEPROM_TMC_X_HOME_SG_THRS (EEPROM_TMC_X + 8) // 1byte, (-64..+63)
  155. #define EEPROM_TMC_X_HOME_CURRENT_R (EEPROM_TMC_X + 9) // 1byte, (-64..+63)
  156. #define EEPROM_TMC_X_HOME_DTCOOLTHRS (EEPROM_TMC_X + 10) // 1byte (-128..+127)
  157. #define EEPROM_TMC_X_DTCOOLTHRS_LOW (EEPROM_TMC_X + 11) // 1byte (-128..+127)
  158. #define EEPROM_TMC_X_DTCOOLTHRS_HIGH (EEPROM_TMC_X + 12) // 1byte (-128..+127)
  159. #define EEPROM_TMC_X_SG_THRS_LOW (EEPROM_TMC_X + 13) // 1byte, (-64..+63)
  160. #define EEPROM_TMC_X_SG_THRS_HIGH (EEPROM_TMC_X + 14) // 1byte, (-64..+63)
  161. // Currently running firmware, each digit stored as uint16_t.
  162. // The flavor differentiates a dev, alpha, beta, release candidate or a release version.
  163. #define EEPROM_FIRMWARE_VERSION_END (FW_PRUSA3D_MAGIC_LEN+8)
  164. #define EEPROM_FIRMWARE_VERSION_FLAVOR (FW_PRUSA3D_MAGIC_LEN+6)
  165. #define EEPROM_FIRMWARE_VERSION_REVISION (FW_PRUSA3D_MAGIC_LEN+4)
  166. #define EEPROM_FIRMWARE_VERSION_MINOR (FW_PRUSA3D_MAGIC_LEN+2)
  167. #define EEPROM_FIRMWARE_VERSION_MAJOR FW_PRUSA3D_MAGIC_LEN
  168. // Magic string, indicating that the current or the previous firmware running was the Prusa3D firmware.
  169. #define EEPROM_FIRMWARE_PRUSA_MAGIC 0
  170. #ifdef __cplusplus
  171. #include "ConfigurationStore.h"
  172. static M500_conf * const EEPROM_M500_base = reinterpret_cast<M500_conf*>(20); //offset for storing settings using M500
  173. #endif
  174. #endif // EEPROM_H