1_75mm_MK3S-EINSy10a-E3Dv6full.h 24 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567568569570571572573574575576577578579580581582583584585586587588589590591592593594595596597598599600601602603604605606607608609610611612613614615616617618619620621622623624625626627628629630631632633634635636637638639640641642643644
  1. #ifndef CONFIGURATION_PRUSA_H
  2. #define CONFIGURATION_PRUSA_H
  3. #include <limits.h>
  4. #include "printers.h"
  5. /*------------------------------------
  6. GENERAL SETTINGS
  7. *------------------------------------*/
  8. // Printer revision
  9. #define PRINTER_TYPE PRINTER_MK3S
  10. #define PRINTER_NAME PRINTER_MK3S_NAME
  11. #define PRINTER_MMU_TYPE PRINTER_MK3S_MMU2
  12. #define PRINTER_MMU_NAME PRINTER_MK3S_MMU2_NAME
  13. #define FILAMENT_SIZE "1_75mm_MK3"
  14. #define NOZZLE_TYPE "E3Dv6full"
  15. // Developer flag
  16. #define DEVELOPER
  17. // Printer name
  18. #define CUSTOM_MENDEL_NAME "Prusa i3 MK3S"
  19. // Electronics
  20. #define MOTHERBOARD BOARD_EINSY_1_0a
  21. #define STEEL_SHEET
  22. #define HAS_SECOND_SERIAL_PORT
  23. // PSU
  24. #define PSU_Delta // uncomment if DeltaElectronics PSU installed
  25. // Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
  26. //#define E3D_PT100_EXTRUDER_WITH_AMP
  27. //#define E3D_PT100_EXTRUDER_NO_AMP
  28. //#define E3D_PT100_BED_WITH_AMP
  29. //#define E3D_PT100_BED_NO_AMP
  30. /*------------------------------------
  31. AXIS SETTINGS
  32. *------------------------------------*/
  33. // Steps per unit {X,Y,Z,E}
  34. //#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,140}
  35. #define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,280}
  36. //#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,560}
  37. // Endstop inverting
  38. #define X_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  39. #define Y_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  40. #define Z_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  41. // Direction inverting
  42. #define INVERT_X_DIR 1 // for Mendel set to 0, for Orca set to 1
  43. #define INVERT_Y_DIR 0 // for Mendel set to 1, for Orca set to 0
  44. #define INVERT_Z_DIR 1 // for Mendel set to 0, for Orca set to 1
  45. #define INVERT_E0_DIR 0 // for direct drive extruder v9 set to 1, for geared extruder set to 0
  46. #define INVERT_E1_DIR 0 // for direct drive extruder v9 set to 1, for geared extruder set to 0
  47. #define INVERT_E2_DIR 0 // for direct drive extruder v9 set to 1, for geared extruder set to 0
  48. // Home position
  49. #define MANUAL_X_HOME_POS 0
  50. #define MANUAL_Y_HOME_POS -2.2
  51. #define MANUAL_Z_HOME_POS 0.2
  52. // Travel limits after homing
  53. #define X_MAX_POS 255
  54. #define X_MIN_POS 0
  55. #define Y_MAX_POS 212.5
  56. #define Y_MIN_POS -4 //orig -4
  57. #define Z_MAX_POS 210
  58. #define Z_MIN_POS 0.15
  59. // Canceled home position
  60. #define X_CANCEL_POS 50
  61. #define Y_CANCEL_POS 190
  62. //Pause print position
  63. #define X_PAUSE_POS 50
  64. #define Y_PAUSE_POS 190
  65. #define Z_PAUSE_LIFT 20
  66. #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
  67. #define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000
  68. //#define DEFAULT_Y_OFFSET 4.f // Default distance of Y_MIN_POS point from endstop, when the printer is not calibrated.
  69. /**
  70. * [0,0] steel sheet print area point X coordinate in bed print area coordinates
  71. */
  72. #define SHEET_PRINT_ZERO_REF_X 0.f
  73. /**
  74. * [0,0] steel sheet print area point Y coordinate in bed print area coordinates
  75. */
  76. #define SHEET_PRINT_ZERO_REF_Y -2.f
  77. #define DEFAULT_MAX_FEEDRATE {200, 200, 12, 120} // (mm/sec) max feedrate (M203)
  78. #define DEFAULT_MAX_FEEDRATE_SILENT {100, 100, 12, 120} // (mm/sec) max feedrate (M203), silent mode
  79. #define DEFAULT_MAX_ACCELERATION {1000, 1000, 200, 5000} // (mm/sec^2) max acceleration (M201)
  80. #define DEFAULT_MAX_ACCELERATION_SILENT {960, 960, 200, 5000} // (mm/sec^2) max acceleration (M201), silent mode
  81. #define DEFAULT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for printing moves (M204S)
  82. #define DEFAULT_RETRACT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for retracts (M204T)
  83. #define MANUAL_FEEDRATE {2700, 2700, 1000, 100} // set the speeds for manual moves (mm/min)
  84. //Silent mode limits
  85. #define SILENT_MAX_ACCEL_XY 960ul // max acceleration in silent mode in mm/s^2
  86. #define SILENT_MAX_FEEDRATE_XY 100 // max feedrate in mm/s
  87. //Normal mode limits
  88. #define NORMAL_MAX_ACCEL_XY 2500ul // max acceleration in normal mode in mm/s^2
  89. #define NORMAL_MAX_FEEDRATE_XY 200 // max feedrate in mm/s
  90. //number of bytes from end of the file to start check
  91. #define END_FILE_SECTION 20000
  92. #define Z_AXIS_ALWAYS_ON 1
  93. //Crash detection
  94. #define CRASHDET_TIMER 45 //seconds
  95. #define CRASHDET_COUNTER_MAX 3
  96. // New XYZ calibration
  97. #define NEW_XYZCAL
  98. // Watchdog support
  99. #define WATCHDOG
  100. // Power panic
  101. #define UVLO_SUPPORT
  102. // Fan check
  103. #define FANCHECK
  104. // Safety timer
  105. #define SAFETYTIMER
  106. #define DEFAULT_SAFETYTIMER_TIME_MINS 30
  107. #define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
  108. // Filament sensor
  109. #define FILAMENT_SENSOR
  110. #define IR_SENSOR
  111. // Backlash -
  112. //#define BACKLASH_X
  113. //#define BACKLASH_Y
  114. // Minimum ambient temperature limit to start triggering MINTEMP errors [C]
  115. // this value is litlebit higher that real limit, because ambient termistor is on the board and is temperated from it,
  116. // temperature inside the case is around 31C for ambient temperature 25C, when the printer is powered on long time and idle
  117. // the real limit is 15C (same as MINTEMP limit), this is because 15C is end of scale for both used thermistors (bed, heater)
  118. #define MINTEMP_MINAMBIENT 25
  119. #define MINTEMP_MINAMBIENT_RAW 978
  120. #define DEBUG_DCODE3
  121. //#define DEBUG_BUILD
  122. //#define DEBUG_SEC_LANG //secondary language debug output at startup
  123. //#define DEBUG_W25X20CL //debug external spi flash
  124. #ifdef DEBUG_BUILD
  125. //#define _NO_ASM
  126. #define DEBUG_DCODES //D codes
  127. #define DEBUG_STACK_MONITOR //Stack monitor in stepper ISR
  128. //#define DEBUG_FSENSOR_LOG //Reports fsensor status to serial
  129. //#define DEBUG_CRASHDET_COUNTERS //Display crash-detection counters on LCD
  130. //#define DEBUG_RESUME_PRINT //Resume/save print debug enable
  131. //#define DEBUG_UVLO_AUTOMATIC_RECOVER // Power panic automatic recovery debug output
  132. //#define DEBUG_DISABLE_XMINLIMIT //x min limit ignored
  133. //#define DEBUG_DISABLE_XMAXLIMIT //x max limit ignored
  134. //#define DEBUG_DISABLE_YMINLIMIT //y min limit ignored
  135. //#define DEBUG_DISABLE_YMAXLIMIT //y max limit ignored
  136. //#define DEBUG_DISABLE_ZMINLIMIT //z min limit ignored
  137. //#define DEBUG_DISABLE_ZMAXLIMIT //z max limit ignored
  138. #define DEBUG_DISABLE_STARTMSGS //no startup messages
  139. //#define DEBUG_DISABLE_MINTEMP //mintemp error ignored
  140. //#define DEBUG_DISABLE_SWLIMITS //sw limits ignored
  141. //#define DEBUG_DISABLE_LCD_STATUS_LINE //empty four lcd line
  142. //#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
  143. //#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
  144. //#define DEBUG_DISABLE_FORCE_SELFTEST //disable force selftest
  145. //#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3)
  146. //#define DEBUG_YSTEP_DUP_PIN 21 //duplicate y-step output to pin 21 (SCL on P3)
  147. //#define DEBUG_DISABLE_FANCHECK //disable fan check (no ISR INT7, check disabled)
  148. //#define DEBUG_DISABLE_FSENSORCHECK //disable fsensor check (no ISR INT7, check disabled)
  149. #define DEBUG_DUMP_TO_2ND_SERIAL //dump received characters to 2nd serial line
  150. #define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message.
  151. #define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display.
  152. #define CMD_DIAGNOSTICS //Show cmd queue length on printer display
  153. #endif /* DEBUG_BUILD */
  154. //#define FSENSOR_QUALITY
  155. #define LINEARITY_CORRECTION
  156. #define TMC2130_LINEARITY_CORRECTION
  157. #define TMC2130_LINEARITY_CORRECTION_XYZ
  158. #define TMC2130_VARIABLE_RESOLUTION
  159. /*------------------------------------
  160. TMC2130 default settings
  161. *------------------------------------*/
  162. #define TMC2130_FCLK 12000000 // fclk = 12MHz
  163. #define TMC2130_USTEPS_XY 16 // microstep resolution for XY axes
  164. #define TMC2130_USTEPS_Z 16 // microstep resolution for Z axis
  165. #define TMC2130_USTEPS_E 32 // microstep resolution for E axis
  166. #define TMC2130_INTPOL_XY 1 // extrapolate 256 for XY axes
  167. #define TMC2130_INTPOL_Z 1 // extrapolate 256 for Z axis
  168. #define TMC2130_INTPOL_E 1 // extrapolate 256 for E axis
  169. #define TMC2130_PWM_GRAD_X 2 // PWMCONF
  170. #define TMC2130_PWM_AMPL_X 230 // PWMCONF
  171. #define TMC2130_PWM_AUTO_X 1 // PWMCONF
  172. #define TMC2130_PWM_FREQ_X 2 // PWMCONF
  173. #define TMC2130_PWM_GRAD_Y 2 // PWMCONF
  174. #define TMC2130_PWM_AMPL_Y 235 // PWMCONF
  175. #define TMC2130_PWM_AUTO_Y 1 // PWMCONF
  176. #define TMC2130_PWM_FREQ_Y 2 // PWMCONF
  177. #define TMC2130_PWM_GRAD_Z 4 // PWMCONF
  178. #define TMC2130_PWM_AMPL_Z 200 // PWMCONF
  179. #define TMC2130_PWM_AUTO_Z 1 // PWMCONF
  180. #define TMC2130_PWM_FREQ_Z 2 // PWMCONF
  181. #define TMC2130_PWM_GRAD_E 4 // PWMCONF
  182. #define TMC2130_PWM_AMPL_E 240 // PWMCONF
  183. #define TMC2130_PWM_AUTO_E 1 // PWMCONF
  184. #define TMC2130_PWM_FREQ_E 2 // PWMCONF
  185. #define TMC2130_TOFF_XYZ 3 // CHOPCONF // fchop = 27.778kHz
  186. #define TMC2130_TOFF_E 3 // CHOPCONF // fchop = 27.778kHz
  187. //#define TMC2130_TOFF_E 4 // CHOPCONF // fchop = 21.429kHz
  188. //#define TMC2130_TOFF_E 5 // CHOPCONF // fchop = 17.442kHz
  189. //#define TMC2130_STEALTH_E // Extruder stealthChop mode
  190. //#define TMC2130_CNSTOFF_E // Extruder constant-off-time mode (similar to MK2)
  191. //#define TMC2130_PWM_DIV 683 // PWM frequency divider (1024, 683, 512, 410)
  192. #define TMC2130_PWM_DIV 512 // PWM frequency divider (1024, 683, 512, 410)
  193. #define TMC2130_PWM_CLK (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk)
  194. #define TMC2130_TPWMTHRS 0 // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode
  195. #define TMC2130_THIGH 0 // THIGH - unused
  196. //#define TMC2130_TCOOLTHRS_X 450 // TCOOLTHRS - coolstep treshold
  197. //#define TMC2130_TCOOLTHRS_Y 450 // TCOOLTHRS - coolstep treshold
  198. #define TMC2130_TCOOLTHRS_X 430 // TCOOLTHRS - coolstep treshold
  199. #define TMC2130_TCOOLTHRS_Y 430 // TCOOLTHRS - coolstep treshold
  200. #define TMC2130_TCOOLTHRS_Z 500 // TCOOLTHRS - coolstep treshold
  201. #define TMC2130_TCOOLTHRS_E 500 // TCOOLTHRS - coolstep treshold
  202. #define TMC2130_SG_HOMING 1 // stallguard homing
  203. #define TMC2130_SG_THRS_X 3 // stallguard sensitivity for X axis
  204. #define TMC2130_SG_THRS_Y 3 // stallguard sensitivity for Y axis
  205. #define TMC2130_SG_THRS_Z 4 // stallguard sensitivity for Z axis
  206. #define TMC2130_SG_THRS_E 3 // stallguard sensitivity for E axis
  207. //new settings is possible for vsense = 1, running current value > 31 set vsense to zero and shift both currents by 1 bit right (Z axis only)
  208. #define TMC2130_CURRENTS_H {16, 20, 35, 30} // default holding currents for all axes
  209. #define TMC2130_CURRENTS_R {16, 20, 35, 30} // default running currents for all axes
  210. #define TMC2130_UNLOAD_CURRENT_R 12 // lowe current for M600 to protect filament sensor
  211. #define TMC2130_STEALTH_Z
  212. //#define TMC2130_SERVICE_CODES_M910_M918
  213. //#define TMC2130_DEBUG
  214. //#define TMC2130_DEBUG_WR
  215. //#define TMC2130_DEBUG_RD
  216. /*------------------------------------
  217. EXTRUDER SETTINGS
  218. *------------------------------------*/
  219. // Mintemps
  220. #define HEATER_0_MINTEMP 15
  221. #define HEATER_1_MINTEMP 5
  222. #define HEATER_2_MINTEMP 5
  223. #define HEATER_MINTEMP_DELAY 15000 // [ms] ! if changed, check maximal allowed value @ ShortTimer
  224. #if HEATER_MINTEMP_DELAY>USHRT_MAX
  225. #error "Check maximal allowed value @ ShortTimer (see HEATER_MINTEMP_DELAY definition)"
  226. #endif
  227. #define BED_MINTEMP 15
  228. #define BED_MINTEMP_DELAY 50000 // [ms] ! if changed, check maximal allowed value @ ShortTimer
  229. #if BED_MINTEMP_DELAY>USHRT_MAX
  230. #error "Check maximal allowed value @ ShortTimer (see BED_MINTEMP_DELAY definition)"
  231. #endif
  232. // Maxtemps
  233. #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
  234. #define HEATER_0_MAXTEMP 410
  235. #else
  236. #define HEATER_0_MAXTEMP 305
  237. #endif
  238. #define HEATER_1_MAXTEMP 305
  239. #define HEATER_2_MAXTEMP 305
  240. #define BED_MAXTEMP 125
  241. #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
  242. // Define PID constants for extruder with PT100
  243. #define DEFAULT_Kp 21.70
  244. #define DEFAULT_Ki 1.60
  245. #define DEFAULT_Kd 73.76
  246. #else
  247. // Define PID constants for extruder
  248. //#define DEFAULT_Kp 40.925
  249. //#define DEFAULT_Ki 4.875
  250. //#define DEFAULT_Kd 86.085
  251. #define DEFAULT_Kp 16.13
  252. #define DEFAULT_Ki 1.1625
  253. #define DEFAULT_Kd 56.23
  254. #endif
  255. // Extrude mintemp
  256. #define EXTRUDE_MINTEMP 175
  257. // Extruder cooling fans
  258. #define EXTRUDER_0_AUTO_FAN_PIN 8
  259. #define EXTRUDER_1_AUTO_FAN_PIN -1
  260. #define EXTRUDER_2_AUTO_FAN_PIN -1
  261. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  262. #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
  263. /*------------------------------------
  264. LOAD/UNLOAD FILAMENT SETTINGS
  265. *------------------------------------*/
  266. // Load filament commands
  267. #define LOAD_FILAMENT_0 "M83"
  268. #define LOAD_FILAMENT_1 "G1 E70 F400"
  269. #define LOAD_FILAMENT_2 "G1 E40 F100"
  270. // Unload filament commands
  271. #define UNLOAD_FILAMENT_0 "M83"
  272. #define UNLOAD_FILAMENT_1 "G1 E-80 F7000"
  273. /*------------------------------------
  274. CHANGE FILAMENT SETTINGS
  275. *------------------------------------*/
  276. // Filament change configuration
  277. #define FILAMENTCHANGEENABLE
  278. #ifdef FILAMENTCHANGEENABLE
  279. #define FILAMENTCHANGE_XPOS 211
  280. #define FILAMENTCHANGE_YPOS 0
  281. #define FILAMENTCHANGE_ZADD 2
  282. #define FILAMENTCHANGE_FIRSTRETRACT -2
  283. #define FILAMENTCHANGE_FINALRETRACT -80
  284. #define FILAMENTCHANGE_FIRSTFEED 70 //E distance in mm for fast filament loading sequence used used in filament change (M600)
  285. #define FILAMENTCHANGE_FINALFEED 25 //E distance in mm for slow filament loading sequence used used in filament change (M600) and filament load (M701)
  286. #define FILAMENTCHANGE_RECFEED 5
  287. #define FILAMENTCHANGE_XYFEED 50
  288. #define FILAMENTCHANGE_EFEED_FIRST 20 // feedrate in mm/s for fast filament loading sequence used in filament change (M600)
  289. #define FILAMENTCHANGE_EFEED_FINAL 3.3f // feedrate in mm/s for slow filament loading sequence used in filament change (M600) and filament load (M701)
  290. //#define FILAMENTCHANGE_RFEED 400
  291. #define FILAMENTCHANGE_RFEED 7000 / 60
  292. #define FILAMENTCHANGE_EXFEED 2
  293. #define FILAMENTCHANGE_ZFEED 15
  294. #endif
  295. /*------------------------------------
  296. ADDITIONAL FEATURES SETTINGS
  297. *------------------------------------*/
  298. // Define Prusa filament runout sensor
  299. //#define FILAMENT_RUNOUT_SUPPORT
  300. #ifdef FILAMENT_RUNOUT_SUPPORT
  301. #define FILAMENT_RUNOUT_SENSOR 1
  302. #endif
  303. // temperature runaway
  304. #define TEMP_RUNAWAY_BED_HYSTERESIS 5
  305. #define TEMP_RUNAWAY_BED_TIMEOUT 360
  306. #define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
  307. #define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
  308. /*------------------------------------
  309. MOTOR CURRENT SETTINGS
  310. *------------------------------------*/
  311. // Motor Current settings for Einsy/tmc = 0..63
  312. #define MOTOR_CURRENT_PWM_RANGE 63
  313. /*------------------------------------
  314. BED SETTINGS
  315. *------------------------------------*/
  316. // Define Mesh Bed Leveling system to enable it
  317. #define MESH_BED_LEVELING
  318. #ifdef MESH_BED_LEVELING
  319. #define MBL_Z_STEP 0.01
  320. // Mesh definitions
  321. #define MESH_MIN_X 24
  322. #define MESH_MAX_X 228
  323. #define MESH_MIN_Y 6
  324. #define MESH_MAX_Y 210
  325. // Mesh upsample definition
  326. #define MESH_NUM_X_POINTS 7
  327. #define MESH_NUM_Y_POINTS 7
  328. // Mesh measure definition
  329. #define MESH_MEAS_NUM_X_POINTS 3
  330. #define MESH_MEAS_NUM_Y_POINTS 3
  331. // Maximum bed level correction value
  332. #define BED_ADJUSTMENT_UM_MAX 100
  333. #define MESH_HOME_Z_CALIB 0.2
  334. #define MESH_HOME_Z_SEARCH 5.0f // Z lift for homing, mesh bed leveling etc.
  335. #define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right
  336. #define Y_PROBE_OFFSET_FROM_EXTRUDER 5 // Z probe to nozzle Y offset: -front +behind
  337. #define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!)
  338. #endif
  339. // Bed Temperature Control
  340. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  341. //
  342. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  343. // If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
  344. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  345. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  346. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  347. // shouldn't use bed PID until someone else verifies your hardware works.
  348. // If this is enabled, find your own PID constants below.
  349. #define PIDTEMPBED
  350. //
  351. //#define BED_LIMIT_SWITCHING
  352. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  353. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  354. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  355. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  356. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  357. // Bed temperature compensation settings
  358. #define BED_OFFSET 10
  359. #define BED_OFFSET_START 40
  360. #define BED_OFFSET_CENTER 50
  361. #ifdef PIDTEMPBED
  362. //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  363. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  364. #if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
  365. // Define PID constants for extruder with PT100
  366. #define DEFAULT_bedKp 21.70
  367. #define DEFAULT_bedKi 1.60
  368. #define DEFAULT_bedKd 73.76
  369. #else
  370. #define DEFAULT_bedKp 126.13
  371. #define DEFAULT_bedKi 4.30
  372. #define DEFAULT_bedKd 924.76
  373. #endif
  374. //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  375. //from pidautotune
  376. // #define DEFAULT_bedKp 97.1
  377. // #define DEFAULT_bedKi 1.41
  378. // #define DEFAULT_bedKd 1675.16
  379. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  380. #endif // PIDTEMPBED
  381. //connect message when communication with monitoring broken
  382. //#define FARM_CONNECT_MESSAGE
  383. /*-----------------------------------
  384. PREHEAT SETTINGS
  385. *------------------------------------*/
  386. #define FARM_PREHEAT_HOTEND_TEMP 250
  387. #define FARM_PREHEAT_HPB_TEMP 80
  388. #define PLA_PREHEAT_HOTEND_TEMP 215
  389. #define PLA_PREHEAT_HPB_TEMP 60
  390. #define ASA_PREHEAT_HOTEND_TEMP 260
  391. #define ASA_PREHEAT_HPB_TEMP 105
  392. #define ABS_PREHEAT_HOTEND_TEMP 255
  393. #define ABS_PREHEAT_HPB_TEMP 100
  394. #define HIPS_PREHEAT_HOTEND_TEMP 220
  395. #define HIPS_PREHEAT_HPB_TEMP 100
  396. #define PP_PREHEAT_HOTEND_TEMP 254
  397. #define PP_PREHEAT_HPB_TEMP 100
  398. #define PET_PREHEAT_HOTEND_TEMP 230
  399. #define PET_PREHEAT_HPB_TEMP 85
  400. #define FLEX_PREHEAT_HOTEND_TEMP 240
  401. #define FLEX_PREHEAT_HPB_TEMP 50
  402. /*------------------------------------
  403. THERMISTORS SETTINGS
  404. *------------------------------------*/
  405. //
  406. //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  407. //
  408. //// Temperature sensor settings:
  409. // -2 is thermocouple with MAX6675 (only for sensor 0)
  410. // -1 is thermocouple with AD595
  411. // 0 is not used
  412. // 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  413. // 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  414. // 3 is Mendel-parts thermistor (4.7k pullup)
  415. // 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  416. // 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  417. // 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  418. // 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  419. // 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  420. // 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  421. // 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  422. // 10 is 100k RS thermistor 198-961 (4.7k pullup)
  423. // 11 is 100k beta 3950 1% thermistor (4.7k pullup)
  424. // 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  425. // 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  426. // 20 is the PT100 circuit found in the Ultimainboard V2.x
  427. // 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  428. //
  429. // 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
  430. // (but gives greater accuracy and more stable PID)
  431. // 51 is 100k thermistor - EPCOS (1k pullup)
  432. // 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  433. // 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  434. //
  435. // 1047 is Pt1000 with 4k7 pullup
  436. // 1010 is Pt1000 with 1k pullup (non standard)
  437. // 147 is Pt100 with 4k7 pullup
  438. // 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a
  439. // 247 is Pt100 with 4k7 pullup and PT100 Amplifier
  440. // 110 is Pt100 with 1k pullup (non standard)
  441. #if defined(E3D_PT100_EXTRUDER_WITH_AMP)
  442. #define TEMP_SENSOR_0 247
  443. #elif defined(E3D_PT100_EXTRUDER_NO_AMP)
  444. #define TEMP_SENSOR_0 148
  445. #else
  446. #define TEMP_SENSOR_0 5
  447. #endif
  448. #define TEMP_SENSOR_1 0
  449. #define TEMP_SENSOR_2 0
  450. #if defined(E3D_PT100_BED_WITH_AMP)
  451. #define TEMP_SENSOR_BED 247
  452. #elif defined(E3D_PT100_BED_NO_AMP)
  453. #define TEMP_SENSOR_BED 148
  454. #else
  455. #define TEMP_SENSOR_BED 1
  456. #endif
  457. #define TEMP_SENSOR_PINDA 1
  458. #define TEMP_SENSOR_AMBIENT 2000
  459. #define STACK_GUARD_TEST_VALUE 0xA2A2
  460. #define MAX_BED_TEMP_CALIBRATION 50
  461. #define MAX_HOTEND_TEMP_CALIBRATION 50
  462. #define MAX_E_STEPS_PER_UNIT 250
  463. #define MIN_E_STEPS_PER_UNIT 100
  464. #define Z_BABYSTEP_MIN -3999
  465. #define Z_BABYSTEP_MAX 0
  466. #define PINDA_PREHEAT_X 20
  467. #define PINDA_PREHEAT_Y 60
  468. #define PINDA_PREHEAT_Z 0.15
  469. /*
  470. #define PINDA_PREHEAT_X 70
  471. #define PINDA_PREHEAT_Y -3
  472. #define PINDA_PREHEAT_Z 1*/
  473. #define PINDA_HEAT_T 120 //time in s
  474. #define PINDA_MIN_T 50
  475. #define PINDA_STEP_T 10
  476. #define PINDA_MAX_T 100
  477. #define PING_TIME 60 //time in s
  478. #define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
  479. #define PING_ALLERT_PERIOD 60 //time in s
  480. #define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
  481. #define NC_BUTTON_LONG_PRESS 15 //time in s
  482. #define LONG_PRESS_TIME 1000 //time in ms for button long press
  483. #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
  484. #define DEFAULT_PID_TEMP 210
  485. #define MIN_PRINT_FAN_SPEED 75
  486. // How much shall the print head be lifted on power panic?
  487. // Ideally the Z axis will reach a zero phase of the stepper driver on power outage. To simplify this,
  488. // UVLO_Z_AXIS_SHIFT shall be an integer multiply of the stepper driver cycle, that is 4x full step.
  489. // For example, the Prusa i3 MK2 with 16 microsteps per full step has Z stepping of 400 microsteps per mm.
  490. // At 400 microsteps per mm, a full step lifts the Z axis by 0.04mm, and a stepper driver cycle is 0.16mm.
  491. // The following example, 12 * (4 * 16 / 400) = 12 * 0.16mm = 1.92mm.
  492. //#define UVLO_Z_AXIS_SHIFT 1.92
  493. #define UVLO_Z_AXIS_SHIFT 0.64
  494. // If power panic occured, and the current temperature is higher then target temperature before interrupt minus this offset, print will be recovered automatically.
  495. #define AUTOMATIC_UVLO_BED_TEMP_OFFSET 5
  496. #define HEATBED_V2
  497. #define M600_TIMEOUT 600 //seconds
  498. //#define SUPPORT_VERBOSITY
  499. #define MMU_REQUIRED_FW_BUILDNR 83
  500. #define MMU_HWRESET
  501. #define MMU_DEBUG //print communication between MMU2 and printer on serial
  502. //#define MMU_HAS_CUTTER
  503. // This is experimental feature requested by our test department.
  504. // There is no known use for ordinary user. If enabled by this macro
  505. // and enabled from printer menu (not enabled by default). It cuts filament
  506. // every time when switching filament from gcode. MMU_HAS_CUTTER needs to be
  507. // defined.
  508. //#define MMU_ALWAYS_CUT
  509. #define MMU_IDLER_SENSOR_ATTEMPTS_NR 21 //max. number of attempts to load filament if first load failed; value for max bowden length and case when loading fails right at the beginning
  510. #endif //__CONFIGURATION_PRUSA_H