PrusaFirmware/lang/po/Firmware_fr.po

# Translation of Prusa-Firmware into French.
#
msgid ""
msgstr ""
"MIME-Version: 1.0\n"
"Content-Type: text/plain; charset=UTF-8\n"
"Content-Transfer-Encoding: 8bit\n"
"Language: fr\n"
"Project-Id-Version: Prusa-Firmware\n"
"POT-Creation-Date: Mo 1. Mär 08:42:29 CET 2021\n"
"PO-Revision-Date: Mo 1. Mär 08:42:29 CET 2021\n"
"Language-Team: \n"
"X-Generator: Poedit 2.0.7\n"
"X-Poedit-SourceCharset: UTF-8\n"
"Last-Translator: \n"
"Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"

# 
#: 
msgid "[%.7s]Live adj. Z\x0avalue set, continue\x0aor start from zero?\x0a%cContinue%cReset"
msgstr "[%.7s]Ajust. du Z\x0aValeur enreg, contin\x0aou depart a zero?\x0a%cContinuer%cReset"

# MSG_IR_03_OR_OLDER c=18
#: messages.c:168
msgid " 0.3 or older"
msgstr " 0.3 ou +ancien"

#  c=18
#: Marlin_main.cpp:9669
msgid "FS v0.3 or older"
msgstr "FS v0.3 ou +ancien"

# MSG_IR_04_OR_NEWER c=18
#: messages.c:167
msgid " 0.4 or newer"
msgstr " 0.4 ou +recent"

#  c=18
#: Marlin_main.cpp:9668
msgid "FS v0.4 or newer"
msgstr "FS v0.4 ou +recent"

# MSG_IR_UNKNOWN c=18
#: messages.c:169
msgid "unknown state"
msgstr "Etat inconnu"

# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE2 c=14
#: messages.c:44
msgid " of 4"
msgstr " de 4"

# MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
#: messages.c:67
msgid " of 9"
msgstr " de 9"

# MSG_MEASURED_OFFSET
#: ultralcd.cpp:3015
msgid "[0;0] point offset"
msgstr "Offset point [0;0]"

# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
#: 
msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
msgstr "La detection de\x0acrash peut etre\x0aactive seulement en\x0amode Normal"

# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
#: 
msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
msgstr "ATTENTION:\x0aDetection de crash\x0adesactivee en\x0amode furtif"

# 
#: ultralcd.cpp:2430
msgid ">Cancel"
msgstr ">Annuler"

# MSG_BABYSTEPPING_Z c=15
#: ultralcd.cpp:3135
msgid "Adjusting Z:"
msgstr "Ajuster Z:"

# MSG_SELFTEST_CHECK_ALLCORRECT c=20
#: ultralcd.cpp:8507
msgid "All correct      "
msgstr "Tout est correct"

# MSG_WIZARD_DONE c=20 r=8
#: messages.c:118
msgid "All is done. Happy printing!"
msgstr "Tout est pret. Bonne impression!"

# 
#: ultralcd.cpp:1915
msgid "Ambient"
msgstr "Ambiant"

# MSG_AUTO c=6
#: messages.c:164
msgid "Auto"
msgstr ""

# MSG_PRESS c=20 r=2
#: ultralcd.cpp:2594
msgid "and press the knob"
msgstr "et appuyez sur le bouton"

# MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
#: ultralcd.cpp:3456
msgid "Are left and right Z~carriages all up?"
msgstr "Z~carriages gauche + droite tout en haut?"

# MSG_AUTO_DEPLETE c=17 r=1
#: messages.c:129
msgid "SpoolJoin"
msgstr ""

# MSG_AUTO_HOME
#: messages.c:11
msgid "Auto home"
msgstr "Mise a 0 des axes"

# MSG_AUTOLOAD_FILAMENT c=18
#: ultralcd.cpp:6837
msgid "AutoLoad filament"
msgstr "Autocharge du fil."

# MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
#: ultralcd.cpp:4418
msgid "Autoloading filament available only when filament sensor is turned on..."
msgstr "Chargement auto du filament uniquement si le capteur de filament est active."

# MSG_AUTOLOADING_ENABLED c=20 r=4
#: ultralcd.cpp:2757
msgid "Autoloading filament is active, just press the knob and insert filament..."
msgstr "Chargement auto. du fil. active, appuyez sur le bouton et inserez le fil."

# MSG_SELFTEST_AXIS_LENGTH
#: ultralcd.cpp:8190
msgid "Axis length"
msgstr "Longueur de l'axe"

# MSG_SELFTEST_AXIS
#: ultralcd.cpp:8191
msgid "Axis"
msgstr "Axe"

# MSG_SELFTEST_BEDHEATER
#: ultralcd.cpp:8148
msgid "Bed / Heater"
msgstr "Lit / Chauffage"

# MSG_BED_DONE
#: messages.c:15
msgid "Bed done"
msgstr "Plateau termine"

# MSG_BED_HEATING
#: messages.c:16
msgid "Bed Heating"
msgstr "Chauffe du lit"

# MSG_BED_CORRECTION_MENU
#: ultralcd.cpp:5904
msgid "Bed level correct"
msgstr "Corr. niveau plateau"

# MSG_BELTTEST c=17
#: ultralcd.cpp:5884
msgid "Belt test        "
msgstr "Test de courroie "

# MSG_BED_LEVELING_FAILED_POINT_LOW c=20 r=5
#: messages.c:17
msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
msgstr "Capt. non declenche pendant que je nivele le plateau. Debris sur buse? En attente d'un reset."

# MSG_BRIGHT c=6
#: messages.c:162
msgid "Bright"
msgstr "Brill."

# MSG_BRIGHTNESS c=18
#: messages.c:158
msgid "Brightness"
msgstr "Luminosite"

# MSG_BED
#: messages.c:14
msgid "Bed"
msgstr "Lit"

# MSG_BELT_STATUS c=18
#: messages.c:19
msgid "Belt status"
msgstr "Statut courroie"

# MSG_RECOVER_PRINT c=20 r=2
#: messages.c:82
msgid "Blackout occurred. Recover print?"
msgstr "Coupure detectee. Reprendre impression?"

# 
#: ultralcd.cpp:8509
msgid "Calibrating home"
msgstr "Calib. mise a 0"

# MSG_CALIBRATE_BED
#: ultralcd.cpp:5893
msgid "Calibrate XYZ"
msgstr "Calibrer XYZ"

# MSG_HOMEYZ
#: messages.c:52
msgid "Calibrate Z"
msgstr "Calibrer Z"

# MSG_CALIBRATE_PINDA c=17 r=1
#: ultralcd.cpp:4637
msgid "Calibrate"
msgstr "Calibrer"

# MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
#: ultralcd.cpp:3419
msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
msgstr "Calibration de XYZ. Tournez le bouton pour faire monter l'extrudeur dans l'axe Z jusqu'aux butees. Cliquez une fois fait."

# MSG_CALIBRATE_Z_AUTO c=20 r=2
#: messages.c:20
msgid "Calibrating Z"
msgstr "Calibration Z"

# MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
#: ultralcd.cpp:3419
msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
msgstr "Calibration de Z. Tournez le bouton pour faire monter l'extrudeur dans l'axe Z jusqu'aux butees. Cliquez une fois fait."

# MSG_HOMEYZ_DONE
#: ultralcd.cpp:843
msgid "Calibration done"
msgstr "Calibration terminee"

# MSG_MENU_CALIBRATION
#: messages.c:68
msgid "Calibration"
msgstr ""

# 
#: ultralcd.cpp:4815
msgid "Cancel"
msgstr "Annuler"

# MSG_SD_REMOVED
#: ultralcd.cpp:8955
msgid "Card removed"
msgstr "Carte retiree"

# 
#: ultralcd.cpp:8599
msgid "Checking file"
msgstr ""

# MSG_NOT_COLOR
#: ultralcd.cpp:2674
msgid "Color not correct"
msgstr "Couleur incorrecte"

# MSG_COOLDOWN
#: messages.c:26
msgid "Cooldown"
msgstr "Refroidissement"

# 
#: ultralcd.cpp:4543
msgid "Copy selected language?"
msgstr "Copier la langue choisie?"

# MSG_CRASHDETECT c=13
#: messages.c:29
msgid "Crash det."
msgstr "Detect.crash"

# 
#: ultralcd.cpp:4950
msgid "Choose a filament for the First Layer Calibration and select it in the on-screen menu."
msgstr "Choisissez un filament pour la Calibration de la Premiere Couche et selectionnez-le depuis le menu a l'ecran."

# MSG_CRASH_DETECTED c=20 r=1
#: messages.c:28
msgid "Crash detected."
msgstr "Crash detecte."

# 
#: Marlin_main.cpp:653
msgid "Crash detected. Resume print?"
msgstr "Crash detecte. Poursuivre l'impression?"

# MSG_CRASH c=7
#: messages.c:27
msgid "Crash"
msgstr ""

# MSG_CURRENT c=19 r=1
#: ultralcd.cpp:6035
msgid "Current"
msgstr "Actuel"

# MSG_DATE c=17 r=1
#: ultralcd.cpp:2118
msgid "Date:"
msgstr "Date:"

# MSG_COMMUNITY_MADE c=18
#: messages.c:24
msgid "Community made"
msgstr ""

# MSG_DISABLE_STEPPERS
#: ultralcd.cpp:5785
msgid "Disable steppers"
msgstr "Desactiver moteurs"

# MSG_BABYSTEP_Z_NOT_SET c=20 r=12
#: messages.c:13
msgid "Distance between tip of the nozzle and the bed surface has not been set yet. Please follow the manual, chapter First steps, section First layer calibration."
msgstr "La distance entre la pointe de la buse et la surface du plateau n'a pas encore ete reglee. Suivez le manuel, chapitre Premiers pas, section Calibration de la premiere couche."

# MSG_FS_CONTINUE c=5
#: messages.c:156
msgid "Cont."
msgstr ""

# MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
#: ultralcd.cpp:5129
msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
msgstr "Voulez-vous refaire l'etape pour reajuster la hauteur entre la buse et le plateau chauffant?"

# MSG_EXTRUDER_CORRECTION c=13
#: ultralcd.cpp:5198
msgid "E-correct:"
msgstr "Correct-E:"

# MSG_EJECT_FILAMENT c=16
#: messages.c:59
msgid "Eject filament"
msgstr "Remonter le fil."

# MSG_EJECTING_FILAMENT c=20 r=1
#: mmu.cpp:1414
msgid "Ejecting filament"
msgstr "Le fil. remonte"

# MSG_SELFTEST_ENDSTOP_NOTHIT c=20
#: ultralcd.cpp:8166
msgid "Endstop not hit"
msgstr "Butee non atteinte"

# MSG_SELFTEST_ENDSTOP
#: ultralcd.cpp:8161
msgid "Endstop"
msgstr "Butee"

# MSG_SELFTEST_ENDSTOPS
#: ultralcd.cpp:8152
msgid "Endstops"
msgstr "Butees"

# MSG_STACK_ERROR c=20 r=4
#: ultralcd.cpp:6872
msgid "Error - static memory has been overwritten"
msgstr "Erreur - la memoire statique a ete ecrasee"

# MSG_CUT_FILAMENT c=16
#: messages.c:60
msgid "Cut filament"
msgstr "Coupe filament"

# MSG_CUTTER c=9
#: messages.c:130
msgid "Cutter"
msgstr "Coupeur"

#  c=18
#: mmu.cpp:1386
msgid "Cutting filament"
msgstr "Je coupe filament"

# MSG_FSENS_NOT_RESPONDING c=20 r=4
#: ultralcd.cpp:4431
msgid "ERROR: Filament sensor is not responding, please check connection."
msgstr "ERREUR: Le capteur de filament ne repond pas, verifiez le branchement."

# MSG_DIM c=6
#: messages.c:163
msgid "Dim"
msgstr ""

# MSG_ERROR
#: messages.c:30
msgid "ERROR:"
msgstr "ERREUR:"

# MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
#: ultralcd.cpp:8515
msgid "Extruder fan:"
msgstr "Ventilo extrudeur:"

# MSG_INFO_EXTRUDER c=18
#: ultralcd.cpp:2173
msgid "Extruder info"
msgstr "Infos extrudeur"

# MSG_EXTRUDER c=17
#: messages.c:31
msgid "Extruder"
msgstr "Extrudeur"

# 
#: ultralcd.cpp:6859
msgid "Fail stats MMU"
msgstr "Stat. d'echec MMU"

# MSG_FSENSOR_AUTOLOAD c=13
#: messages.c:48
msgid "F. autoload"
msgstr "F. autocharg."

# 
#: ultralcd.cpp:6856
msgid "Fail stats"
msgstr "Stat. d'echec"

# MSG_FAN_SPEED c=14
#: messages.c:35
msgid "Fan speed"
msgstr "Vitesse vent."

# MSG_SELFTEST_FAN c=20
#: messages.c:91
msgid "Fan test"
msgstr "Test du ventilateur"

# MSG_FANS_CHECK c=13
#: messages.c:32
msgid "Fans check"
msgstr "Verif vent."

# MSG_FSENSOR
#: messages.c:49
msgid "Fil. sensor"
msgstr "Capteur Fil."

# MSG_FIL_RUNOUTS c=15
#: messages.c:33
msgid "Fil. runouts"
msgstr "Fins filament"

# MSG_FILAMENT_CLEAN c=20 r=2
#: messages.c:36
msgid "Filament extruding & with correct color?"
msgstr "Filament extrude et avec bonne couleur?"

# MSG_NOT_LOADED c=19
#: ultralcd.cpp:2673
msgid "Filament not loaded"
msgstr "Filament non charge"

# MSG_FILAMENT_SENSOR c=20
#: messages.c:97
msgid "Filament sensor"
msgstr "Capteur de filament"

# MSG_FILAMENT_USED c=19
#: ultralcd.cpp:2822
msgid "Filament used"
msgstr "Filament utilise"

# MSG_PRINT_TIME c=19 r=1
#: ultralcd.cpp:2823
msgid "Print time"
msgstr "Temps d'impression"

# MSG_FS_ACTION c=10
#: messages.c:155
msgid "FS Action"
msgstr ""

# MSG_FILE_INCOMPLETE c=20 r=3
#: ultralcd.cpp:8657
msgid "File incomplete. Continue anyway?"
msgstr "Fichier incomplet. Continuer qd meme?"

# MSG_FINISHING_MOVEMENTS c=20
#: messages.c:45
msgid "Finishing movements"
msgstr "Mouvement final"

# MSG_V2_CALIBRATION c=18
#: messages.c:124
msgid "First layer cal."
msgstr "Cal. 1ere couche"

# MSG_WIZARD_SELFTEST c=20 r=8
#: ultralcd.cpp:5050
msgid "First, I will run the selftest to check most common assembly problems."
msgstr "D'abord, je vais lancer le Auto-test pour verifier les problemes d'assemblage les plus communs."

# 
#: mmu.cpp:726
msgid "Fix the issue and then press button on MMU unit."
msgstr "Corrigez le probleme et appuyez sur le bouton sur la MMU."

# MSG_FLOW
#: ultralcd.cpp:6999
msgid "Flow"
msgstr "Flux"

# MSG_PRUSA3D_FORUM
#: ultralcd.cpp:2111
msgid "forum.prusa3d.com"
msgstr ""

# MSG_SELFTEST_COOLING_FAN c=20
#: messages.c:88
msgid "Front print fan?"
msgstr "Ventilo impr avant?"

# MSG_BED_CORRECTION_FRONT c=14 r=1
#: ultralcd.cpp:3217
msgid "Front side[um]"
msgstr "Avant [um]"

# MSG_SELFTEST_FANS
#: ultralcd.cpp:8196
msgid "Front/left fans"
msgstr "Ventilos avt/gauche"

# MSG_SELFTEST_HEATERTHERMISTOR
#: ultralcd.cpp:8144
msgid "Heater/Thermistor"
msgstr "Chauffage/Thermistor"

# MSG_BED_HEATING_SAFETY_DISABLED
#: Marlin_main.cpp:9659
msgid "Heating disabled by safety timer."
msgstr "Chauffage desactivee par le compteur de securite."

# MSG_HEATING_COMPLETE c=20
#: messages.c:51
msgid "Heating done."
msgstr "Chauffe terminee."

# MSG_HEATING
#: messages.c:50
msgid "Heating"
msgstr "Chauffe"

# MSG_WIZARD_WELCOME c=20 r=7
#: messages.c:121
msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
msgstr "Bonjour, je suis votre imprimante Original Prusa i3. Voulez-vous que je vous guide a travers le processus d'installation?"

# MSG_PRUSA3D_HOWTO
#: ultralcd.cpp:2112
msgid "howto.prusa3d.com"
msgstr ""

# MSG_FILAMENTCHANGE
#: messages.c:42
msgid "Change filament"
msgstr "Changer filament"

# MSG_CHANGE_SUCCESS
#: ultralcd.cpp:2603
msgid "Change success!"
msgstr "Changement reussi!"

# MSG_CORRECTLY c=20
#: ultralcd.cpp:2671
msgid "Changed correctly?"
msgstr "Change correctement?"

# MSG_SELFTEST_CHECK_BED c=20
#: messages.c:94
msgid "Checking bed     "
msgstr "Verif. plateau chauf"

# MSG_SELFTEST_CHECK_ENDSTOPS c=20
#: ultralcd.cpp:8498
msgid "Checking endstops"
msgstr "Verification butees"

# MSG_SELFTEST_CHECK_HOTEND c=20
#: ultralcd.cpp:8504
msgid "Checking hotend  "
msgstr "Verif. du hotend"

# MSG_SELFTEST_CHECK_FSENSOR c=20
#: messages.c:95
msgid "Checking sensors "
msgstr "Verif. des capteurs"

# MSG_CHECKING_X c=20
#: messages.c:22
msgid "Checking X axis"
msgstr "Verification axe X"

# MSG_CHECKING_Y c=20
#: messages.c:23
msgid "Checking Y axis"
msgstr "Verification axe Y"

# MSG_SELFTEST_CHECK_Z c=20
#: ultralcd.cpp:8501
msgid "Checking Z axis"
msgstr "Verification axe Z"

# MSG_CHOOSE_EXTRUDER c=20 r=1
#: messages.c:53
msgid "Choose extruder:"
msgstr "Choisir extrudeur:"

# MSG_CHOOSE_FILAMENT c=20 r=1
#: messages.c:54
msgid "Choose filament:"
msgstr "Choix du filament:"

# MSG_FILAMENT c=17 r=1
#: messages.c:34
msgid "Filament"
msgstr ""

# MSG_WIZARD_XYZ_CAL c=20 r=8
#: ultralcd.cpp:5059
msgid "I will run xyz calibration now. It will take approx. 12 mins."
msgstr "Je vais maintenant lancer la calibration XYZ. Cela prendra 12 min environ."

# MSG_WIZARD_Z_CAL c=20 r=8
#: ultralcd.cpp:5067
msgid "I will run z calibration now."
msgstr "Je vais maintenant lancer la calibration Z."

# MSG_WATCH
#: messages.c:116
msgid "Info screen"
msgstr "Ecran d'info"

# MSG_INSERT_FILAMENT c=20
#: ultralcd.cpp:2591
msgid "Insert filament"
msgstr "Inserez le filament"

# MSG_FILAMENT_LOADED c=20 r=2
#: messages.c:37
msgid "Is filament loaded?"
msgstr "Fil. est-il charge?"

# MSG_STEEL_SHEET_CHECK c=20 r=2
#: messages.c:109
msgid "Is steel sheet on heatbed?"
msgstr "Est la plaque sur le plat. chauffant?"

# MSG_LAST_PRINT_FAILURES c=20
#: messages.c:56
msgid "Last print failures"
msgstr "Echecs derniere imp."

# MSG_WIZARD_WELCOME_SHIPPING c=20 r=16
#: messages.c:122
msgid "Hi, I am your Original Prusa i3 printer. I will guide you through a short setup process, in which the Z-axis will be calibrated. Then, you will be ready to print."
msgstr "Bonjour, je suis votre imprimante Original Prusa i3. Je vais vous accompagner au cours d'un bref processus de reglage, qui permettra de calibrer le Z-axis. Apres cela, tout sera pret pour imprimer."

# 
#: ultralcd.cpp:5137
msgid "If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets."
msgstr "Si vous avez d'autres feuilles d'acier,  calibrez leurs pre-reglages dans Reglages - Config HW - Plaque en acier."

# MSG_LAST_PRINT c=18
#: messages.c:55
msgid "Last print"
msgstr "Derniere impres."

# MSG_SELFTEST_EXTRUDER_FAN c=20
#: messages.c:89
msgid "Left hotend fan?"
msgstr "Ventilo gauche?"

# 
#: ultralcd.cpp:2946
msgid "Left"
msgstr "Gauche"

# MSG_BED_CORRECTION_LEFT c=14 r=1
#: ultralcd.cpp:3215
msgid "Left side [um]"
msgstr "Gauche [um]"

# 
#: ultralcd.cpp:5808
msgid "Lin. correction"
msgstr "Correction lin."

# MSG_BABYSTEP_Z
#: messages.c:12
msgid "Live adjust Z"
msgstr "Ajuster Z en dir."

#  c=20 r=6
#: ultralcd.cpp:7397
msgid "Insert the filament (do not load it) into the extruder and then press the knob."
msgstr "Veuillez inserer le filament ( ne le chargez pas) dans l'extrudeur, puis appuyez sur le bouton."

# MSG_LOAD_FILAMENT c=17
#: messages.c:57
msgid "Load filament"
msgstr "Charger filament"

# MSG_LOADING_COLOR
#: ultralcd.cpp:2625
msgid "Loading color"
msgstr "Charg. de la couleur"

# MSG_LOADING_FILAMENT c=20
#: messages.c:58
msgid "Loading filament"
msgstr "Chargement du fil."

# MSG_LOOSE_PULLEY c=20 r=1
#: ultralcd.cpp:8184
msgid "Loose pulley"
msgstr "Poulie lache"

# 
#: ultralcd.cpp:6822
msgid "Load to nozzle"
msgstr "Charger la buse"

# MSG_M117_V2_CALIBRATION c=25
#: messages.c:61
msgid "M117 First layer cal."
msgstr "M117 Cal. 1ere couche"

# MSG_MAIN
#: messages.c:62
msgid "Main"
msgstr "Menu principal"

# MSG_BL_HIGH c=12
#: messages.c:159
msgid "Level Bright"
msgstr "Niveau brill"

# MSG_BL_LOW c=12
#: messages.c:160
msgid "Level Dimmed"
msgstr ""

# MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
#: messages.c:66
msgid "Measuring reference height of calibration point"
msgstr "Je mesure la hauteur de reference du point de calibrage"

# MSG_MESH_BED_LEVELING c=18
#: messages.c:152
msgid "Mesh Bed Leveling"
msgstr ""

# MSG_MMU_OK_RESUMING_POSITION c=20 r=4
#: mmu.cpp:764
msgid "MMU OK. Resuming position..."
msgstr "MMU OK. Reprise de la position ..."

# MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
#: mmu.cpp:757
msgid "MMU OK. Resuming temperature..."
msgstr "MMU OK. Rechauffage de la buse..."

# 
#: ultralcd.cpp:2987
msgid "Measured skew"
msgstr "Deviat.mesuree"

# MSG_MMU_FAILS c=15
#: messages.c:69
msgid "MMU fails"
msgstr "Echecs MMU"

# 
#: mmu.cpp:1586
msgid "MMU load failed     "
msgstr "Echec chargement MMU"

# MSG_MMU_LOAD_FAILS c=15
#: messages.c:70
msgid "MMU load fails"
msgstr "Echecs charg. MMU"

# MSG_MMU_OK_RESUMING c=20 r=4
#: mmu.cpp:775
msgid "MMU OK. Resuming..."
msgstr "MMU OK. Reprise ..."

# MSG_MODE
#: messages.c:103
msgid "Mode"
msgstr ""

#  c=20 r=3
#: Marlin_main.cpp:899
msgid "MK3 firmware detected on MK3S printer"
msgstr "Firmware MK3 detecte sur imprimante MK3S"

# MSG_NORMAL
#: messages.c:107
msgid "Normal"
msgstr ""

# MSG_SILENT
#: messages.c:106
msgid "Silent"
msgstr "Furtif"

# 
#: mmu.cpp:721
msgid "MMU needs user attention."
msgstr "Le MMU necessite l'attention de l'utilisateur."

# 
#: ultralcd.cpp:1705
msgid "MMU power fails"
msgstr "Echecs alim. MMU"

# MSG_STEALTH
#: messages.c:108
msgid "Stealth"
msgstr "Furtif"

# MSG_AUTO_POWER
#: messages.c:105
msgid "Auto power"
msgstr "Puiss.auto"

# MSG_HIGH_POWER
#: messages.c:104
msgid "High power"
msgstr "Haute puiss"

# 
#: ultralcd.cpp:2130
msgid "MMU2 connected"
msgstr "MMU2 connecte"

# MSG_SELFTEST_MOTOR
#: messages.c:96
msgid "Motor"
msgstr "Moteur"

# MSG_MOVE_AXIS
#: ultralcd.cpp:5783
msgid "Move axis"
msgstr "Deplacer l'axe"

# MSG_MOVE_X
#: ultralcd.cpp:4334
msgid "Move X"
msgstr "Deplacer X"

# MSG_MOVE_Y
#: ultralcd.cpp:4335
msgid "Move Y"
msgstr "Deplacer Y"

# MSG_MOVE_Z
#: ultralcd.cpp:4336
msgid "Move Z"
msgstr "Deplacer Z"

# MSG_NO_MOVE
#: Marlin_main.cpp:5720
msgid "No move."
msgstr "Pas de mouvement."

# MSG_NO_CARD
#: ultralcd.cpp:6802
msgid "No SD card"
msgstr "Pas de carte SD"

# MSG_NA
#: messages.c:128
msgid "N/A"
msgstr ""

# MSG_NO
#: messages.c:71
msgid "No"
msgstr "Non"

# MSG_SELFTEST_NOTCONNECTED
#: ultralcd.cpp:8145
msgid "Not connected"
msgstr "Non connecte"

# 
#: util.cpp:294
msgid "New firmware version available:"
msgstr "Nouvelle version de firmware disponible:"

# MSG_SELFTEST_FAN_NO c=19
#: messages.c:92
msgid "Not spinning"
msgstr "Ne tourne pas"

# MSG_WIZARD_V2_CAL c=20 r=8
#: ultralcd.cpp:4946
msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
msgstr "Maintenant je vais calibrer la distance entre la pointe de la buse et la surface du plateau chauffant."

# MSG_WIZARD_WILL_PREHEAT c=20 r=4
#: ultralcd.cpp:5075
msgid "Now I will preheat nozzle for PLA."
msgstr "Maintenant je vais prechauffer la buse pour du PLA."

# MSG_NOZZLE
#: messages.c:72
msgid "Nozzle"
msgstr "Buse"

# MSG_DEFAULT_SETTINGS_LOADED c=20 r=5
#: Marlin_main.cpp:1564
msgid "Old settings found. Default PID, Esteps etc. will be set."
msgstr "Anciens reglages trouves. Le PID, les Esteps etc. par defaut seront regles"

# 
#: ultralcd.cpp:5066
msgid "Now remove the test print from steel sheet."
msgstr "Retirez maintenant l'impression de test de la plaque en acier."

# 
#: ultralcd.cpp:1634
msgid "Nozzle FAN"
msgstr "Vent. buse"

# MSG_PAUSE_PRINT c=18
#: messages.c:74
msgid "Pause print"
msgstr "Pause de l'impr."

# MSG_PID_RUNNING c=20 r=1
#: ultralcd.cpp:1514
msgid "PID cal.           "
msgstr "Calib. PID"

# MSG_PID_FINISHED c=20 r=1
#: ultralcd.cpp:1520
msgid "PID cal. finished"
msgstr "Calib. PID terminee"

# MSG_PID_EXTRUDER c=17 r=1
#: ultralcd.cpp:5905
msgid "PID calibration"
msgstr "Calibration PID"

# MSG_PINDA_PREHEAT c=20 r=1
#: ultralcd.cpp:870
msgid "PINDA Heating"
msgstr "Chauffe de la PINDA"

# MSG_PAPER c=20 r=10
#: messages.c:73
msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
msgstr "Placez une feuille de papier sous la buse pendant la calibration des 4 premiers points. Si la buse accroche le papier, eteignez vite l'imprimante."

# MSG_WIZARD_CLEAN_HEATBED c=20 r=8
#: ultralcd.cpp:5132
msgid "Please clean heatbed and then press the knob."
msgstr "Nettoyez plateau chauffant en acier et appuyez sur le bouton."

# MSG_CONFIRM_NOZZLE_CLEAN c=20 r=8
#: messages.c:25
msgid "Please clean the nozzle for calibration. Click when done."
msgstr "Nettoyez la buse pour la calibration. Cliquez une fois fait."

# MSG_SELFTEST_PLEASECHECK
#: ultralcd.cpp:8139
msgid "Please check :"
msgstr "Verifiez:"

# MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
#: messages.c:117
msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
msgstr "Merci de consulter notre manuel et de corriger le probleme. Poursuivez alors l'assistant en redemarrant l'imprimante."

# MSG_CHECK_IDLER c=20 r=4
#: Marlin_main.cpp:3301
msgid "Please open idler and remove filament manually."
msgstr "Ouvrez l'idler et retirez le filament manuellement."

# MSG_PLACE_STEEL_SHEET c=20 r=4
#: messages.c:75
msgid "Please place steel sheet on heatbed."
msgstr "Placez la plaque en acier sur le plateau chauffant."

# MSG_PRESS_TO_UNLOAD c=20 r=4
#: messages.c:79
msgid "Please press the knob to unload filament"
msgstr "Appuyez sur le bouton pour decharger le filament"

# MSG_PULL_OUT_FILAMENT c=20 r=4
#: messages.c:81
msgid "Please pull out filament immediately"
msgstr "Retirez immediatement le filament"

# MSG_EJECT_REMOVE c=20 r=4
#: mmu.cpp:1420
msgid "Please remove filament and then press the knob."
msgstr "Veuillez retirer le filament puis appuyez sur le bouton."

# MSG_REMOVE_STEEL_SHEET c=20 r=4
#: messages.c:84
msgid "Please remove steel sheet from heatbed."
msgstr "Retirez la plaque en acier du plateau chauffant."

# MSG_RUN_XYZ c=20 r=4
#: Marlin_main.cpp:4817
msgid "Please run XYZ calibration first."
msgstr "Veuillez d'abord lancer la calibration XYZ."

# MSG_UPDATE_MMU2_FW c=20 r=4
#: mmu.cpp:1340
msgid "Please update firmware in your MMU2. Waiting for reset."
msgstr "Veuillez mettre a jour le firmware de votre MMU2. En attente d'un reset."

# MSG_PLEASE_WAIT c=20
#: messages.c:76
msgid "Please wait"
msgstr "Merci de patienter"

# 
#: ultralcd.cpp:5065
msgid "Please remove shipping helpers first."
msgstr "Retirez d'abord les protections de transport."

# MSG_PREHEAT_NOZZLE c=20
#: messages.c:78
msgid "Preheat the nozzle!"
msgstr "Prechauffez la buse!"

# MSG_PREHEAT
#: ultralcd.cpp:6760
msgid "Preheat"
msgstr "Prechauffage"

# MSG_WIZARD_HEATING c=20 r=3
#: messages.c:119
msgid "Preheating nozzle. Please wait."
msgstr "Prechauffage de la buse. Merci de patienter."

#  c=14
#: ultralcd.cpp:1918
msgid "PINDA"
msgstr ""

# 
#: util.cpp:298
msgid "Please upgrade."
msgstr "Mettez a jour le FW."

# MSG_PRESS_TO_PREHEAT c=20 r=4
#: Marlin_main.cpp:11761
msgid "Press the knob to preheat nozzle and continue."
msgstr "Appuyez sur le bouton pour prechauffer la buse et continuer."

# MSG_FS_PAUSE c=5
#: fsensor.cpp:730
msgid "Pause"
msgstr ""

# MSG_POWER_FAILURES c=15
#: messages.c:77
msgid "Power failures"
msgstr "Coup.de courant"

# MSG_PRINT_ABORTED c=20
#: messages.c:80
msgid "Print aborted"
msgstr "Impression annulee"

#  c=20
#: ultralcd.cpp:2410
msgid "Preheating to load"
msgstr "Chauffe pour charger"

#  c=20
#: ultralcd.cpp:2415
msgid "Preheating to unload"
msgstr "Chauf.pour decharger"

# MSG_SELFTEST_PRINT_FAN_SPEED c=18
#: ultralcd.cpp:8518
msgid "Print fan:"
msgstr "Vent. impr:"

# MSG_CARD_MENU
#: messages.c:21
msgid "Print from SD"
msgstr "Impr. depuis la SD"

#  c=20
#: ultralcd.cpp:2251
msgid "Press the knob"
msgstr "App. sur sur bouton"

# MSG_PRINT_PAUSED c=20 r=1
#: ultralcd.cpp:1094
msgid "Print paused"
msgstr "Impression en pause"

# 
#: mmu.cpp:725
msgid "Press the knob to resume nozzle temperature."
msgstr "Appuyez sur le bouton pour rechauffer la buse."

# MSG_FOLLOW_CALIBRATION_FLOW c=20 r=8
#: messages.c:46
msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
msgstr "L'imprimante n'a pas encore ete calibree. Suivez le manuel, chapitre Premiers pas, section Processus de calibration."

# 
#: ultralcd.cpp:1635
msgid "Print FAN"
msgstr "Vent. impr"

# 
#: ultralcd.cpp:4926
msgid "Please insert filament into the extruder, then press the knob to load it."
msgstr "Veuillez inserer le filament dans l'extrudeur, puis appuyez sur le bouton pour le charger."

# 
#: ultralcd.cpp:4921
msgid "Please insert filament into the first tube of the MMU, then press the knob to load it."
msgstr "Veuillez inserer le filament dans le premier tube du MMU, puis appuyez sur le bouton pour le charger."

# 
#: ultralcd.cpp:4843
msgid "Please load filament first."
msgstr "Veuillez d'abord charger un filament."

# MSG_PRUSA3D
#: ultralcd.cpp:2110
msgid "prusa3d.com"
msgstr ""

# MSG_BED_CORRECTION_REAR c=14 r=1
#: ultralcd.cpp:3218
msgid "Rear side [um]"
msgstr "Arriere [um]"

#  c=20 r=4
#: ultralcd.cpp:7421
msgid "Please unload the filament first, then repeat this action."
msgstr "SVP, dechargez le filament et reessayez."

#  c=20 r=4
#: ultralcd.cpp:7424
msgid "Please check the IR sensor connection, unload filament if present."
msgstr "SVP, verifiez la connexion du capteur IR et decharge le filament."

# MSG_RECOVERING_PRINT c=20
#: Marlin_main.cpp:11118
msgid "Recovering print    "
msgstr "Recup. impression   "

# MSG_REMOVE_OLD_FILAMENT c=20 r=5
#: mmu.cpp:832
msgid "Remove old filament and press the knob to start loading new filament."
msgstr "Retirez l'ancien filament puis appuyez sur le bouton pour charger le nouveau."

#  c=20
#: 
msgid "Prusa i3 MK3S OK."
msgstr ""

# MSG_CALIBRATE_BED_RESET
#: ultralcd.cpp:5910
msgid "Reset XYZ calibr."
msgstr "Reinit. calib. XYZ"

# MSG_RESET c=14
#: messages.c:85
msgid "Reset"
msgstr "Reinitialiser"

# MSG_RESUME_PRINT c=18
#: messages.c:86
msgid "Resume print"
msgstr "Reprendre impression"

# MSG_RESUMING_PRINT c=20
#: messages.c:87
msgid "Resuming print"
msgstr "Reprise de l'impr."

# MSG_BED_CORRECTION_RIGHT c=14 r=1
#: ultralcd.cpp:3216
msgid "Right side[um]"
msgstr "Droite [um]"

# MSG_RPI_PORT
#: messages.c:146
msgid "RPi port"
msgstr "Port RPi"

# MSG_WIZARD_RERUN c=20 r=7
#: ultralcd.cpp:4864
msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
msgstr "Lancement de l'Assistant supprimera les resultats actuels de calibration et commencera du debut. Continuer?"

# MSG_SD_CARD
#: messages.c:141
msgid "SD card"
msgstr "Carte SD"

# MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY
#: messages.c:142
msgid "FlashAir"
msgstr "FlshAir"

# 
#: ultralcd.cpp:2947
msgid "Right"
msgstr "Droite"

# MSG_FIND_BED_OFFSET_AND_SKEW_LINE1 c=60
#: messages.c:43
msgid "Searching bed calibration point"
msgstr "Recherche du point de calibration du plateau chauffant"

# MSG_LANGUAGE_SELECT
#: ultralcd.cpp:4559
msgid "Select language"
msgstr "Choisir langue"

# MSG_SELFTEST_OK
#: ultralcd.cpp:7696
msgid "Self test OK"
msgstr "Auto-test OK"

# MSG_SELFTEST_START c=20
#: ultralcd.cpp:7464
msgid "Self test start  "
msgstr "Debut auto-test"

# MSG_SELFTEST
#: ultralcd.cpp:5886
msgid "Selftest         "
msgstr "Auto-test"

# MSG_SELFTEST_ERROR
#: ultralcd.cpp:8138
msgid "Selftest error !"
msgstr "Erreur auto-test!"

# MSG_SELFTEST_FAILED c=20
#: messages.c:90
msgid "Selftest failed  "
msgstr "Echec de l'auto-test"

# MSG_FORCE_SELFTEST c=20 r=8
#: Marlin_main.cpp:1596
msgid "Selftest will be run to calibrate accurate sensorless rehoming."
msgstr "Le Selftest sera lance pour calibrer la remise a zero precise sans capteur"

# 
#: ultralcd.cpp:5106
msgid "Select nozzle preheat temperature which matches your material."
msgstr "Selectionnez la temperature de prechauffage de la buse qui correspond a votre materiau."

# MSG_SET_TEMPERATURE c=19 r=1
#: ultralcd.cpp:3236
msgid "Set temperature:"
msgstr "Regler temp.:"

#  c=20
#: 
msgid "Prusa i3 MK2.5 OK."
msgstr ""

#  c=20
#: 
msgid "Prusa i3 MK2.5S OK."
msgstr ""

#  c=20
#: 
msgid "Prusa i3 MK3 OK."
msgstr ""

# MSG_SETTINGS
#: messages.c:99
msgid "Settings"
msgstr "Reglages"

# MSG_SHOW_END_STOPS c=18
#: ultralcd.cpp:5907
msgid "Show end stops"
msgstr "Afficher butees"

# 
#: ultralcd.cpp:3949
msgid "Sensor state"
msgstr "Etat capteur"

# MSG_FILE_CNT c=20 r=6
#: cardreader.cpp:821
msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
msgstr "Certains fichiers ne seront pas tries. Max 100 fichiers tries par dossier."

# MSG_SORT
#: messages.c:143
msgid "Sort"
msgstr "Tri"

# MSG_NONE
#: messages.c:131
msgid "None"
msgstr "Aucun"

# MSG_SORT_TIME
#: messages.c:144
msgid "Time"
msgstr "Heure"

# 
#: ultralcd.cpp:2990
msgid "Severe skew:"
msgstr "Deviat.sev.:"

# MSG_SORT_ALPHA
#: messages.c:145
msgid "Alphabet"
msgstr ""

# MSG_SORTING c=20 r=1
#: cardreader.cpp:828
msgid "Sorting files"
msgstr "Tri des fichiers"

# MSG_SOUND_LOUD
#: messages.c:148
msgid "Loud"
msgstr "Fort"

# 
#: ultralcd.cpp:2989
msgid "Slight skew:"
msgstr "Deviat.leg.:"

# MSG_SOUND
#: messages.c:147
msgid "Sound"
msgstr "Son"

#  c=7
#: ultralcd.cpp:1781
msgid "Runouts"
msgstr ""

# 
#: Marlin_main.cpp:5331
msgid "Some problem encountered, Z-leveling enforced ..."
msgstr "Probleme rencontre, cliquez sur le bouton pour niveller l'axe Z..."

# MSG_SOUND_ONCE
#: messages.c:149
msgid "Once"
msgstr "Une fois"

# MSG_SPEED
#: ultralcd.cpp:6993
msgid "Speed"
msgstr "Vitesse"

# MSG_SELFTEST_FAN_YES c=19
#: messages.c:93
msgid "Spinning"
msgstr "Tourne"

# MSG_TEMP_CAL_WARNING c=20 r=4
#: Marlin_main.cpp:4830
msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
msgstr "Une temperature ambiante stable de 21-26C et un support stable sont requis."

# MSG_STATISTICS
#: ultralcd.cpp:6852
msgid "Statistics  "
msgstr "Statistiques"

# MSG_STOP_PRINT
#: messages.c:110
msgid "Stop print"
msgstr "Arreter impression"

# MSG_STOPPED
#: messages.c:111
msgid "STOPPED. "
msgstr "ARRETE."

# MSG_SUPPORT
#: ultralcd.cpp:6861
msgid "Support"
msgstr ""

# MSG_SELFTEST_SWAPPED
#: ultralcd.cpp:8197
msgid "Swapped"
msgstr "Echange"

# 
#: ultralcd.cpp:4814
msgid "Select filament:"
msgstr "Selectionnez le filament:"

# MSG_TEMP_CALIBRATION c=14
#: messages.c:112
msgid "Temp. cal."
msgstr "Calib. Temp."

# 
#: ultralcd.cpp:4955
msgid "Select temperature which matches your material."
msgstr "Selectionnez la temperature qui correspond a votre materiau."

# MSG_CALIBRATION_PINDA_MENU c=17 r=1
#: ultralcd.cpp:5918
msgid "Temp. calibration"
msgstr "Calibration temp."

# MSG_TEMP_CAL_FAILED c=20 r=8
#: ultralcd.cpp:3872
msgid "Temperature calibration failed"
msgstr "Echec de la calibration en temperature"

# MSG_TEMP_CALIBRATION_DONE c=20 r=12
#: messages.c:113
msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
msgstr "La calibration en temperature est terminee et activee. La calibration en temperature peut etre desactivee dans le menu Reglages-> Cal. Temp."

#  c=20 r=3
#: ultralcd.cpp:7428
msgid "Sensor verified, remove the filament now."
msgstr "Capteur verifie, retirez le filament maintenant."

# MSG_TEMPERATURE
#: ultralcd.cpp:5781
msgid "Temperature"
msgstr ""

# MSG_MENU_TEMPERATURES c=15 r=1
#: ultralcd.cpp:2180
msgid "Temperatures"
msgstr ""

# MSG_FOLLOW_Z_CALIBRATION_FLOW c=20 r=9
#: messages.c:47
msgid "There is still a need to make Z calibration. Please follow the manual, chapter First steps, section Calibration flow."
msgstr "Il faut toujours effectuer la Calibration Z. Veuillez suivre le manuel, chapitre Premiers pas, section Processus de calibration."

# 
#: ultralcd.cpp:2844
msgid "Total filament"
msgstr "Filament total"

# 
#: ultralcd.cpp:2845
msgid "Total print time"
msgstr "Temps total impr."

# MSG_TUNE
#: ultralcd.cpp:6758
msgid "Tune"
msgstr "Regler"

# 
#: 
msgid "Unload"
msgstr "Decharger"

# MSG_TOTAL_FAILURES c=20
#: messages.c:101
msgid "Total failures"
msgstr "Total des echecs"

#  c=20
#: ultralcd.cpp:2258
msgid "to load filament"
msgstr "pour charger le fil."

#  c=20
#: ultralcd.cpp:2262
msgid "to unload filament"
msgstr "pour decharger fil."

# MSG_UNLOAD_FILAMENT c=17
#: messages.c:114
msgid "Unload filament"
msgstr "Decharger fil."

# MSG_UNLOADING_FILAMENT c=20 r=1
#: messages.c:115
msgid "Unloading filament"
msgstr "Dechargement fil."

# MSG_TOTAL c=6
#: messages.c:100
msgid "Total"
msgstr "Totale"

# MSG_USED c=19 r=1
#: ultralcd.cpp:6034
msgid "Used during print"
msgstr "Utilise pdt impr."

# MSG_MENU_VOLTAGES c=15 r=1
#: ultralcd.cpp:2183
msgid "Voltages"
msgstr "Tensions"

# 
#: ultralcd.cpp:2138
msgid "unknown"
msgstr "inconnu"

# MSG_USERWAIT
#: Marlin_main.cpp:3834
msgid "Wait for user..."
msgstr "Attente utilisateur..."

# MSG_WAITING_TEMP c=20 r=3
#: ultralcd.cpp:3384
msgid "Waiting for nozzle and bed cooling"
msgstr "Attente du refroidissement des buse et plateau chauffant"

# MSG_WAITING_TEMP_PINDA c=20 r=3
#: ultralcd.cpp:3345
msgid "Waiting for PINDA probe cooling"
msgstr "Attente du refroidissement de la sonde PINDA"

# 
#: 
msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
msgstr "Utilisez Remonter le fil. pour retirer le filament 1 s'il depasse du tube arriere du MMU. Utilisez ejecter s'il est cache dans le tube."

# MSG_CHANGED_BOTH c=20 r=4
#: Marlin_main.cpp:1556
msgid "Warning: both printer type and motherboard type changed."
msgstr "Attention: Types d'imprimante et de carte mere modifies"

# MSG_CHANGED_MOTHERBOARD c=20 r=4
#: Marlin_main.cpp:1548
msgid "Warning: motherboard type changed."
msgstr "Attention: Type de carte mere modifie."

# MSG_CHANGED_PRINTER c=20 r=4
#: Marlin_main.cpp:1552
msgid "Warning: printer type changed."
msgstr "Attention: Type d'imprimante modifie"

# MSG_UNLOAD_SUCCESSFUL c=20 r=2
#: Marlin_main.cpp:3292
msgid "Was filament unload successful?"
msgstr "Dechargement du filament reussi?"

# MSG_SELFTEST_WIRINGERROR
#: messages.c:98
msgid "Wiring error"
msgstr "Erreur de cablage"

# MSG_WIZARD c=17 r=1
#: ultralcd.cpp:5877
msgid "Wizard"
msgstr "Assistant"

# MSG_XYZ_DETAILS c=18
#: ultralcd.cpp:2172
msgid "XYZ cal. details"
msgstr "Details calib. XYZ"

# MSG_BED_SKEW_OFFSET_DETECTION_FITTING_FAILED c=20 r=8
#: messages.c:18
msgid "XYZ calibration failed. Please consult the manual."
msgstr "Echec calibration XYZ. Consultez le manuel."

# MSG_YES
#: messages.c:123
msgid "Yes"
msgstr "Oui"

# MSG_WIZARD_QUIT c=20 r=8
#: messages.c:120
msgid "You can always resume the Wizard from Calibration -> Wizard."
msgstr "Vous pouvez toujours relancer l'Assistant dans Calibration > Assistant."

# MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
#: ultralcd.cpp:3844
msgid "XYZ calibration all right. Skew will be corrected automatically."
msgstr "Calibration XYZ OK. L'ecart sera corrige automatiquement."

# MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
#: ultralcd.cpp:3841
msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
msgstr "Calibration XYZ OK. Les axes X/Y sont legerement non perpendiculaires. Bon boulot!"

# MSG_TIMEOUT c=12
#: messages.c:161
msgid "Timeout"
msgstr ""

# MSG_X_CORRECTION c=13
#: ultralcd.cpp:5194
msgid "X-correct:"
msgstr "Correct-X:"

# MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
#: ultralcd.cpp:3838
msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
msgstr "Calibration XYZ OK. Les axes X/Y sont perpendiculaires. Felicitations!"

# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
#: ultralcd.cpp:3822
msgid "XYZ calibration compromised. Front calibration points not reachable."
msgstr "Calibration XYZ compromise. Les points de calibration en avant ne sont pas atteignables."

# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
#: ultralcd.cpp:3825
msgid "XYZ calibration compromised. Right front calibration point not reachable."
msgstr "Calibration XYZ compromise. Le point de calibration avant droit n'est pas atteignable."

# MSG_LOAD_ALL c=17
#: ultralcd.cpp:6273
msgid "Load all"
msgstr "Charger un par un"

# 
#: ultralcd.cpp:3804
msgid "XYZ calibration failed. Bed calibration point was not found."
msgstr "Echec calibration XYZ. Le point de calibration du plateau n'a pas ete trouve."

# 
#: ultralcd.cpp:3810
msgid "XYZ calibration failed. Front calibration points not reachable."
msgstr "Echec calibration XYZ. Les points de calibration en avant ne sont pas atteignables."

# 
#: ultralcd.cpp:3813
msgid "XYZ calibration failed. Right front calibration point not reachable."
msgstr "Echec calibration XYZ. Le point de calibration avant droit n'est pas atteignable."

# 
#: ultralcd.cpp:2944
msgid "Y distance from min"
msgstr "Distance Y du min"

# 
#: ultralcd.cpp:4958
msgid "The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)."
msgstr "L'imprimante commencera a  imprimer une ligne en zig-zag. Tournez le bouton jusqu'a atteindre la hauteur optimale. Consultez les photos dans le manuel (chapitre Calibration)."

#  c=20 r=5
#: ultralcd.cpp:7432
msgid "Verification failed, remove the filament and try again."
msgstr "Verification en echec, retirez le filament et reessayez."

# MSG_Y_CORRECTION c=13
#: ultralcd.cpp:5195
msgid "Y-correct:"
msgstr "Correct-Y:"

# MSG_OFF
#: messages.c:126
msgid "Off"
msgstr ""

# MSG_ON
#: messages.c:127
msgid "On"
msgstr ""

# 
#: messages.c:63
msgid "Back"
msgstr "Retour"

# 
#: ultralcd.cpp:5749
msgid "Checks"
msgstr "Verifications"

# 
#: ultralcd.cpp:8207
msgid "False triggering"
msgstr "Faux declenchement"

# 
#: 
msgid "FINDA:"
msgstr "FINDA:"

# MSG_FIRMWARE
#: language.h:24
msgid "Firmware"
msgstr ""

# MSG_STRICT
#: messages.c:133
msgid "Strict"
msgstr "Stricte"

# MSG_WARN
#: messages.c:132
msgid "Warn"
msgstr "Avert"

# MSG_HW_SETUP c=18
#: messages.c:102
msgid "HW Setup"
msgstr "Config HW"

# 
#: 
msgid "IR:"
msgstr "IR:"

# MSG_MAGNETS_COMP
#: messages.c:154
msgid "Magnets comp."
msgstr "Compens. aim."

# MSG_MESH
#: messages.c:151
msgid "Mesh"
msgstr ""

# 
#: Marlin_main.cpp:892
msgid "MK3S firmware detected on MK3 printer"
msgstr "Firmware MK3S detecte sur imprimante MK3"

# MSG_MMU_MODE
#: messages.c:140
msgid "MMU Mode"
msgstr "Mode MMU"

# 
#: ultralcd.cpp:4467
msgid "Mode change in progress ..."
msgstr "Changement de mode en cours..."

# MSG_MODEL
#: messages.c:134
msgid "Model"
msgstr "Modele"

# MSG_NOZZLE_DIAMETER
#: messages.c:139
msgid "Nozzle d."
msgstr "Diam. buse"

# 
#: util.cpp:515
msgid "G-code sliced for a different level. Continue?"
msgstr "Le G-code a ete prepare pour un niveau different. Continuer?"

# 
#: util.cpp:521
msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
msgstr "Le G-code a ete prepare pour un niveau different. Veuillez decouper le modele a nouveau. L'impression a ete annulee."

# MSG_GCODE_DIFF_PRINTER_CONTINUE c=20 r=5
#: messages.c:137
msgid "G-code sliced for a different printer type. Continue?"
msgstr "Le G-code a ete prepare pour une autre version de l'imprimante. Continuer?"

# MSG_GCODE_DIFF_PRINTER_CANCELLED c=20 r=7
#: messages.c:138
msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
msgstr "Le G-code a ete prepare pour une autre version de l'imprimante. Veuillez decouper le modele a nouveau. L'impression a ete annulee."

# 
#: util.cpp:482
msgid "G-code sliced for a newer firmware. Continue?"
msgstr "Le G-code a ete prepare pour une version plus recente du firmware. Continuer?"

# 
#: util.cpp:488
msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
msgstr "Le G-code a ete prepare pour une version plus recente du firmware. Veuillez mettre a jour le firmware. L'impression annulee."

# 
#: 
msgid "PINDA:"
msgstr "PINDA:"

#  c=20
#: ultralcd.cpp:2422
msgid "Preheating to cut"
msgstr "Chauffe pour couper"

#  c=20
#: ultralcd.cpp:2419
msgid "Preheating to eject"
msgstr "Chauf. pour remonter"

# 
#: util.cpp:395
msgid "Printer nozzle diameter differs from the G-code. Continue?"
msgstr "Diametre de la buse dans les reglages ne correspond pas a celui dans le G-Code. Continuer?"

# 
#: util.cpp:402
msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
msgstr "Diametre de la buse dans les reglages ne correspond pas a celui dans le G-Code. Merci de verifier le parametre dans les reglages. Impression annulee."

#  c=20
#: ultralcd.cpp:8212
msgid "%s level expected"
msgstr ""

# 
#: ultralcd.cpp:6684
msgid "Rename"
msgstr "Renommer"

# 
#: ultralcd.cpp:6677
msgid "Select"
msgstr "Selectionner"

# 
#: ultralcd.cpp:2174
msgid "Sensor info"
msgstr "Info capteur"

# MSG_SHEET c=10
#: messages.c:64
msgid "Sheet"
msgstr "Plaque"

# MSG_SOUND_BLIND
#: messages.c:150
msgid "Assist"
msgstr ""

# MSG_STEEL_SHEET c=18
#: messages.c:65
msgid "Steel sheets"
msgstr "Plaques en acier"

# MSG_Z_CORRECTION c=13
#: ultralcd.cpp:5196
msgid "Z-correct:"
msgstr "Correct-Z:"

# MSG_Z_PROBE_NR
#: messages.c:153
msgid "Z-probe nr."
msgstr "Mesurer x-fois"