1_75mm_MK2-RAMBo10a-E3Dv6full.h 15 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452
  1. #ifndef CONFIGURATION_PRUSA_H
  2. #define CONFIGURATION_PRUSA_H
  3. #include <limits.h>
  4. #include "printers.h"
  5. /*------------------------------------
  6. GENERAL SETTINGS
  7. *------------------------------------*/
  8. // Printer revision
  9. #define PRINTER_TYPE PRINTER_MK2
  10. #define PRINTER_NAME PRINTER_MK2_NAME
  11. #define PRINTER_MMU_TYPE PRINTER_MK2 // dummy item (due to successfully compilation / building only)
  12. #define PRINTER_MMU_NAME PRINTER_MK2_NAME // dummy item (due to successfully compilation / building only)
  13. #define FILAMENT_SIZE "1_75mm_MK2"
  14. #define NOZZLE_TYPE "E3Dv6full"
  15. // Developer flag
  16. #define DEVELOPER
  17. // Printer name
  18. #define CUSTOM_MENDEL_NAME "Prusa i3 MK2"
  19. // Electronics
  20. #define MOTHERBOARD BOARD_RAMBO_MINI_1_0
  21. // Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
  22. //#define E3D_PT100_EXTRUDER_WITH_AMP
  23. //#define E3D_PT100_EXTRUDER_NO_AMP
  24. //#define E3D_PT100_BED_WITH_AMP
  25. //#define E3D_PT100_BED_NO_AMP
  26. /*------------------------------------
  27. AXIS SETTINGS
  28. *------------------------------------*/
  29. // Steps per unit {X,Y,Z,E}
  30. #define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,161.3}
  31. // Endstop inverting
  32. #define X_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  33. #define Y_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  34. #define Z_MIN_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  35. // Direction inverting
  36. #define INVERT_X_DIR 0 // for Mendel set to 0, for Orca set to 1
  37. #define INVERT_Y_DIR 0 // for Mendel set to 1, for Orca set to 0
  38. #define INVERT_Z_DIR 0 // for Mendel set to 0, for Orca set to 1
  39. #define INVERT_E0_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0
  40. #define INVERT_E1_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0
  41. #define INVERT_E2_DIR 1 // for direct drive extruder v9 set to 1, for geared extruder set to 0
  42. // Home position
  43. #define MANUAL_X_HOME_POS 0
  44. #define MANUAL_Y_HOME_POS -2.2
  45. #define MANUAL_Z_HOME_POS 0.15
  46. // Travel limits after homing
  47. #define X_MAX_POS 250
  48. #define X_MIN_POS 0
  49. #define Y_MAX_POS 210
  50. #define Y_MIN_POS -2.2
  51. #define Z_MAX_POS 210
  52. #define Z_MIN_POS 0.15
  53. // Canceled home position
  54. #define X_CANCEL_POS 50
  55. #define Y_CANCEL_POS 190
  56. //Pause print position
  57. #define X_PAUSE_POS 50
  58. #define Y_PAUSE_POS 190
  59. #define Z_PAUSE_LIFT 20
  60. #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
  61. #define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min)
  62. #define DEFAULT_MAX_FEEDRATE {500, 500, 12, 120} // (mm/sec)
  63. #define DEFAULT_MAX_FEEDRATE_SILENT {172, 172, 12, 120} // (mm/sec) max feedrate (M203), silent mode
  64. #define DEFAULT_MAX_ACCELERATION {9000,9000,500,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
  65. #define DEFAULT_MAX_ACCELERATION_SILENT {960, 960, 200, 5000} // (mm/sec^2) max acceleration (M201), silent mode
  66. #define DEFAULT_ACCELERATION 1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
  67. #define DEFAULT_RETRACT_ACCELERATION 1500 // X, Y, Z and E max acceleration in mm/s^2 for retracts
  68. #define DEFAULT_TRAVEL_ACCELERATION 1500 // X, Y, Z and E max acceleration in mm/s^2 for travels
  69. #define MANUAL_FEEDRATE {3000, 3000, 1000, 100} // set the speeds for manual moves (mm/min)
  70. #define Z_AXIS_ALWAYS_ON 1
  71. // New XYZ calibration
  72. //#define NEW_XYZCAL
  73. // Watchdog support
  74. #define WATCHDOG
  75. /*------------------------------------
  76. EXTRUDER SETTINGS
  77. *------------------------------------*/
  78. // Mintemps
  79. #define HEATER_0_MINTEMP 30
  80. #define HEATER_1_MINTEMP 5
  81. #define HEATER_2_MINTEMP 5
  82. #define HEATER_MINTEMP_DELAY 15000 // [ms] ! if changed, check maximal allowed value @ ShortTimer
  83. #if HEATER_MINTEMP_DELAY>USHRT_MAX
  84. #error "Check maximal allowed value @ ShortTimer (see HEATER_MINTEMP_DELAY definition)"
  85. #endif
  86. #define BED_MINTEMP 30
  87. #define BED_MINTEMP_DELAY 50000 // [ms] ! if changed, check maximal allowed value @ ShortTimer
  88. #if BED_MINTEMP_DELAY>USHRT_MAX
  89. #error "Check maximal allowed value @ ShortTimer (see BED_MINTEMP_DELAY definition)"
  90. #endif
  91. // Maxtemps
  92. #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
  93. #define HEATER_0_MAXTEMP 410
  94. #else
  95. #define HEATER_0_MAXTEMP 305
  96. #endif
  97. #define HEATER_1_MAXTEMP 305
  98. #define HEATER_2_MAXTEMP 305
  99. #define BED_MAXTEMP 150
  100. #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
  101. // Define PID constants for extruder with PT100
  102. #define DEFAULT_Kp 21.70
  103. #define DEFAULT_Ki 1.60
  104. #define DEFAULT_Kd 73.76
  105. #else
  106. // Define PID constants for extruder
  107. #define DEFAULT_Kp 40.925
  108. #define DEFAULT_Ki 4.875
  109. #define DEFAULT_Kd 86.085
  110. #endif
  111. // Extrude mintemp
  112. #define EXTRUDE_MINTEMP 175
  113. // Extruder cooling fans
  114. #define EXTRUDER_0_AUTO_FAN_PIN 8
  115. #define EXTRUDER_1_AUTO_FAN_PIN -1
  116. #define EXTRUDER_2_AUTO_FAN_PIN -1
  117. #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
  118. #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
  119. /*------------------------------------
  120. CHANGE FILAMENT SETTINGS
  121. *------------------------------------*/
  122. // Filament change configuration
  123. #define FILAMENTCHANGEENABLE
  124. #ifdef FILAMENTCHANGEENABLE
  125. #define FILAMENTCHANGE_XPOS 211
  126. #define FILAMENTCHANGE_YPOS 0
  127. #define FILAMENTCHANGE_ZADD 2
  128. #define FILAMENTCHANGE_FIRSTRETRACT -2
  129. #define FILAMENTCHANGE_FINALRETRACT -80
  130. #define FILAMENTCHANGE_FIRSTFEED 70 //E distance in mm for fast filament loading sequence used used in filament change (M600)
  131. #define FILAMENTCHANGE_FINALFEED 50 //E distance in mm for slow filament loading sequence used used in filament change (M600) and filament load (M701)
  132. #define FILAMENTCHANGE_RECFEED 5
  133. #define FILAMENTCHANGE_XYFEED 50
  134. #define FILAMENTCHANGE_EFEED_FIRST 20 // feedrate in mm/s for fast filament loading sequence used in filament change (M600)
  135. #define FILAMENTCHANGE_EFEED_FINAL 3.3f // feedrate in mm/s for slow filament loading sequence used in filament change (M600) and filament load (M701)
  136. #define FILAMENTCHANGE_RFEED 400
  137. #define FILAMENTCHANGE_EXFEED 2
  138. #define FILAMENTCHANGE_ZFEED 15
  139. #endif
  140. /*------------------------------------
  141. ADDITIONAL FEATURES SETTINGS
  142. *------------------------------------*/
  143. // Define Prusa filament runout sensor
  144. //#define FILAMENT_RUNOUT_SUPPORT
  145. #ifdef FILAMENT_RUNOUT_SUPPORT
  146. #define FILAMENT_RUNOUT_SENSOR 1
  147. #define FILAMENT_RUNOUT_SCRIPT "M600"
  148. #endif
  149. // temperature runaway
  150. #define TEMP_RUNAWAY_BED_HYSTERESIS 5
  151. #define TEMP_RUNAWAY_BED_TIMEOUT 360
  152. #define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15
  153. #define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45
  154. /*------------------------------------
  155. MOTOR CURRENT SETTINGS
  156. *------------------------------------*/
  157. // Motor Current setting for BIG RAMBo
  158. #define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
  159. #define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135}
  160. // Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range
  161. #if MOTHERBOARD == BOARD_RAMBO_MINI_1_0 || MOTHERBOARD == BOARD_RAMBO_MINI_1_3
  162. #define MOTOR_CURRENT_PWM_RANGE 2000
  163. #define DEFAULT_PWM_MOTOR_CURRENT {270, 830, 450} // {XY,Z,E}
  164. #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 830, 500} // {XY,Z,E}
  165. #define Z_SILENT 0
  166. #define Z_HIGH_POWER 200
  167. #endif
  168. /*------------------------------------
  169. BED SETTINGS
  170. *------------------------------------*/
  171. // Define Mesh Bed Leveling system to enable it
  172. #define MESH_BED_LEVELING
  173. #ifdef MESH_BED_LEVELING
  174. #define MBL_Z_STEP 0.01
  175. // Mesh definitions
  176. #define MESH_MIN_X 35
  177. #define MESH_MAX_X 238
  178. #define MESH_MIN_Y 6
  179. #define MESH_MAX_Y 202
  180. // Mesh upsample definition
  181. #define MESH_NUM_X_POINTS 7
  182. #define MESH_NUM_Y_POINTS 7
  183. // Mesh measure definition
  184. #define MESH_MEAS_NUM_X_POINTS 3
  185. #define MESH_MEAS_NUM_Y_POINTS 3
  186. // Maximum bed level correction value
  187. #define BED_ADJUSTMENT_UM_MAX 100
  188. #define MESH_HOME_Z_CALIB 0.2
  189. #define MESH_HOME_Z_SEARCH 5.0f // Z lift for homing, mesh bed leveling etc.
  190. #define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right
  191. #define Y_PROBE_OFFSET_FROM_EXTRUDER 9 // Z probe to nozzle Y offset: -front +behind
  192. #define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!)
  193. #endif
  194. // Bed Temperature Control
  195. // Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
  196. //
  197. // Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
  198. // If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
  199. // which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
  200. // This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
  201. // If your configuration is significantly different than this and you don't understand the issues involved, you probably
  202. // shouldn't use bed PID until someone else verifies your hardware works.
  203. // If this is enabled, find your own PID constants below.
  204. #define PIDTEMPBED
  205. //
  206. //#define BED_LIMIT_SWITCHING
  207. // This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
  208. // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
  209. // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
  210. // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
  211. #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
  212. // Bed temperature compensation settings
  213. #define BED_OFFSET 10
  214. #define BED_OFFSET_START 40
  215. #define BED_OFFSET_CENTER 50
  216. #ifdef PIDTEMPBED
  217. //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  218. //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
  219. #if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP)
  220. // Define PID constants for extruder with PT100
  221. #define DEFAULT_bedKp 21.70
  222. #define DEFAULT_bedKi 1.60
  223. #define DEFAULT_bedKd 73.76
  224. #else
  225. #define DEFAULT_bedKp 126.13
  226. #define DEFAULT_bedKi 4.30
  227. #define DEFAULT_bedKd 924.76
  228. #endif
  229. //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  230. //from pidautotune
  231. // #define DEFAULT_bedKp 97.1
  232. // #define DEFAULT_bedKi 1.41
  233. // #define DEFAULT_bedKd 1675.16
  234. // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
  235. #endif // PIDTEMPBED
  236. /*-----------------------------------
  237. PREHEAT SETTINGS
  238. *------------------------------------*/
  239. #define FARM_PREHEAT_HOTEND_TEMP 250
  240. #define FARM_PREHEAT_HPB_TEMP 80
  241. #define FARM_PREHEAT_FAN_SPEED 0
  242. #define PLA_PREHEAT_HOTEND_TEMP 215
  243. #define PLA_PREHEAT_HPB_TEMP 55
  244. #define PLA_PREHEAT_FAN_SPEED 0
  245. #define PVB_PREHEAT_HOTEND_TEMP 215
  246. #define PVB_PREHEAT_HPB_TEMP 75
  247. #define PVB_PREHEAT_FAN_SPEED 0
  248. #define ASA_PREHEAT_HOTEND_TEMP 260
  249. #define ASA_PREHEAT_HPB_TEMP 105
  250. #define ASA_PREHEAT_FAN_SPEED 0
  251. #define PC_PREHEAT_HOTEND_TEMP 275
  252. #define PC_PREHEAT_HPB_TEMP 105
  253. #define PC_PREHEAT_FAN_SPEED 0
  254. #define ABS_PREHEAT_HOTEND_TEMP 255
  255. #define ABS_PREHEAT_HPB_TEMP 100
  256. #define ABS_PREHEAT_FAN_SPEED 0
  257. #define HIPS_PREHEAT_HOTEND_TEMP 220
  258. #define HIPS_PREHEAT_HPB_TEMP 100
  259. #define HIPS_PREHEAT_FAN_SPEED 0
  260. #define PP_PREHEAT_HOTEND_TEMP 254
  261. #define PP_PREHEAT_HPB_TEMP 100
  262. #define PP_PREHEAT_FAN_SPEED 0
  263. #define PET_PREHEAT_HOTEND_TEMP 240
  264. #define PET_PREHEAT_HPB_TEMP 90
  265. #define PET_PREHEAT_FAN_SPEED 0
  266. #define FLEX_PREHEAT_HOTEND_TEMP 230
  267. #define FLEX_PREHEAT_HPB_TEMP 50
  268. #define FLEX_PREHEAT_FAN_SPEED 0
  269. /*------------------------------------
  270. THERMISTORS SETTINGS
  271. *------------------------------------*/
  272. //
  273. //--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
  274. //
  275. //// Temperature sensor settings:
  276. // -2 is thermocouple with MAX6675 (only for sensor 0)
  277. // -1 is thermocouple with AD595
  278. // 0 is not used
  279. // 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  280. // 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  281. // 3 is Mendel-parts thermistor (4.7k pullup)
  282. // 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  283. // 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
  284. // 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  285. // 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  286. // 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
  287. // 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  288. // 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  289. // 10 is 100k RS thermistor 198-961 (4.7k pullup)
  290. // 11 is 100k beta 3950 1% thermistor (4.7k pullup)
  291. // 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
  292. // 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
  293. // 20 is the PT100 circuit found in the Ultimainboard V2.x
  294. // 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
  295. //
  296. // 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
  297. // (but gives greater accuracy and more stable PID)
  298. // 51 is 100k thermistor - EPCOS (1k pullup)
  299. // 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
  300. // 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
  301. //
  302. // 1047 is Pt1000 with 4k7 pullup
  303. // 1010 is Pt1000 with 1k pullup (non standard)
  304. // 147 is Pt100 with 4k7 pullup
  305. // 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a
  306. // 247 is Pt100 with 4k7 pullup and PT100 Amplifier
  307. // 110 is Pt100 with 1k pullup (non standard)
  308. #if defined(E3D_PT100_EXTRUDER_WITH_AMP)
  309. #define TEMP_SENSOR_0 247
  310. #elif defined(E3D_PT100_EXTRUDER_NO_AMP)
  311. #define TEMP_SENSOR_0 148
  312. #else
  313. #define TEMP_SENSOR_0 5
  314. #endif
  315. #define TEMP_SENSOR_1 0
  316. #define TEMP_SENSOR_2 0
  317. #if defined(E3D_PT100_BED_WITH_AMP)
  318. #define TEMP_SENSOR_BED 247
  319. #elif defined(E3D_PT100_BED_NO_AMP)
  320. #define TEMP_SENSOR_BED 148
  321. #else
  322. #define TEMP_SENSOR_BED 1
  323. #endif
  324. #define STACK_GUARD_TEST_VALUE 0xA2A2
  325. #define STACK_GUARD_MARGIN 32
  326. #define MAX_BED_TEMP_CALIBRATION 50
  327. #define MAX_HOTEND_TEMP_CALIBRATION 50
  328. #define MAX_E_STEPS_PER_UNIT 250
  329. #define MIN_E_STEPS_PER_UNIT 100
  330. #define Z_BABYSTEP_MIN -3999
  331. #define Z_BABYSTEP_MAX 0
  332. #define PINDA_PREHEAT_X 70
  333. #define PINDA_PREHEAT_Y -3
  334. #define PINDA_PREHEAT_Z 1
  335. #define PINDA_HEAT_T 120 //time in s
  336. #define PINDA_MIN_T 50
  337. #define PINDA_STEP_T 10
  338. #define PINDA_MAX_T 100
  339. #define PING_TIME 60 //time in s
  340. #define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid 0 triggering when dealing with long gcodes
  341. #define PING_ALLERT_PERIOD 60 //time in s
  342. #define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
  343. #define NC_BUTTON_LONG_PRESS 15 //time in s
  344. #define LONG_PRESS_TIME 1000 //time in ms for button long press
  345. #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
  346. #define DEFAULT_PID_TEMP 210
  347. #define END_FILE_SECTION 20000 //number of bytes from end of file used for checking if file is complete
  348. // Safety timer
  349. #define SAFETYTIMER
  350. #define DEFAULT_SAFETYTIMER_TIME_MINS 30
  351. #define FARM_DEFAULT_SAFETYTIMER_TIME_ms (45*60*1000ul)
  352. #define M600_TIMEOUT 600 //seconds
  353. #define MMU_FILAMENT_COUNT 5
  354. #define MMU_REQUIRED_FW_BUILDNR 132
  355. //#define SUPPORT_VERBOSITY
  356. #define MMU_IDLER_SENSOR_ATTEMPTS_NR 21 //max. number of attempts to load filament if first load failed; value for max bowden length and case when loading fails right at the beginning
  357. #endif //__CONFIGURATION_PRUSA_H