README.md 5.2 KB
Table of contents
Build
Linux
Run shell script build.sh to build for MK3 and flash with Slic3er.
If you have a different printer model, follow step 2.b from Windows build first.
If you wish to flash from Arduino, follow step 2.c from Windows build first.
The script downloads Arduino with our modifications and Rambo board support installed, unpacks it into folder PF-build-env-<version> on the same level, as your Prusa-Firmware folder is located, builds firmware for MK3 using that Arduino in Prusa-Firmware-build folder on the same level as Prusa-Firmware, runs secondary language support scripts. Firmware with secondary language support is generated in lang subfolder. Use firmware.hex for MK3 variant. Use firmware_<lang>.hex for other printers. Don't forget to follow step 2.b first for non-MK3 printers.
Windows
1. Development environment preparation
a. install "Arduino Software IDE" for your preferred operating system
https://www.arduino.cc -> Software->Downloads
it is recommended to use version "1.8.5", as it is used on out build server to produce official builds.
note: in the case of persistent compilation problems, check the version of the currently used C/C++ compiler (GCC) - should be 4.8.1; version can be verified by entering the command
avr-gcc --version
if you are not sure where the file is placed (depends on how "Arduino Software IDE" was installed), you can use the search feature within the file system
note: name collision for "LiquidCrystal" library known from previous versions is now obsolete (so there is no need to delete or rename original file/-s)
b. add (UltiMachine) RAMBo board into the list of Arduino target boards
File->Preferences->Settings
into text field "Additional Boards Manager URLs"
type location
"https://raw.githubusercontent.com/ultimachine/ArduinoAddons/master/package_ultimachine_index.json"
or you can 'manually' modify the item
"boardsmanager.additional.urls=....."
at the file "preferences.txt" (this parameter allows you to write a comma-separated list of addresses)
note: you can find location of this file on your disk by doing the following:
File->Preferences->Settings ("More preferences can be edited in file ...")
then choose
Tools->Board->BoardsManager
from viewed list and select the item labeled "RAMBo" (will probably be labeled as "RepRap Arduino-compatible Mother Board (RAMBo) by UltiMachine"
note: select this item for any variant of board used in printers 'Prusa i3 MKx', that is for RAMBo-mini x.y and EINSy x.y to
'clicking' the item will display the installation button; select choice "1.0.1" from the list(last known version as of the date of issue of this document)
(after installation, the item is labeled as "INSTALLED" and can then be used for target board selection)
c. modify platform.txt to enable float printf support:
add "-Wl,-u,vfprintf -lprintf_flt -lm" to "compiler.c.elf.flags=" before existing flag "-Wl,--gc-sections"
example:
"compiler.c.elf.flags=-w -Os -Wl,-u,vfprintf -lprintf_flt -lm -Wl,--gc-sections"
2. Source code compilation
a. place the source codes corresponding to your printer model obtained from the repository into the selected directory on your disk
https://github.com/prusa3d/Prusa-Firmware/
b. In the subdirectory "Firmware/variants/" select the configuration file (.h) corresponding to your printer model, make copy named "Configuration_prusa.h" (or make simple renaming) and copy it into "Firmware/" directory.
c. In file "Firmware/config.h" set LANG_MODE to 0.
run "Arduino IDE"; select the file "Firmware.ino" from the subdirectory "Firmware/" at the location, where you placed the source code
File->Open
make the desired code customizations; all changes are on your own risk!
select the target board "RAMBo"
Tools->Board->RAMBo
note: it is not possible to use any of the variants "Arduino Mega …", even though it is the same MCU
run the compilation
Sketch->Verify/Compile
upload the result code into the connected printer
Sketch->Upload
or you can also save the output code to the file (in so called HEX-format) "Firmware.ino.rambo.hex":
Sketch->ExportCompiledBinary
and then upload it to the printer using the program "FirmwareUpdater"
note: this file is created in the directory "Firmware/"
3. Automated tests
Prerequisites
c++11 compiler e.g. g++ 6.3.1
cmake
build system - ninja or gnu make
Building
Create a folder where you want to build tests.
Example:
cd ..
mkdir Prusa-Firmware-test
Generate build scripts in target folder.
Example:
cd Prusa-Firmware-test
cmake -G "Eclipse CDT4 - Ninja" ../Prusa-Firmware
or for DEBUG build:
cmake -G "Eclipse CDT4 - Ninja" -DCMAKE_BUILD_TYPE=Debug ../Prusa-Firmware
Build it.
Example:
ninja
Runing
./tests
4. Documentation
run doxygen in Firmware folder