Configuration.h 23 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420421422423424425426427428429430431432433434435436437438439440441442443444445446447448449450451452453454455456457458459460461462463464465466467468469470471472473474475476477478479480481482483484485486487488489490491492493494495496497498499500501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530531532533534535536537538539540541542543544545546547548549550551552553554555556557558559560561562563564565566567
  1. #ifndef CONFIGURATION_H
  2. #define CONFIGURATION_H
  3. #include "boards.h"
  4. #define STR_HELPER(x) #x
  5. #define STR(x) STR_HELPER(x)
  6. //-//
  7. #include <avr/pgmspace.h>
  8. extern const uint16_t _nPrinterType;
  9. extern const char _sPrinterName[] PROGMEM;
  10. extern const uint16_t _nPrinterMmuType;
  11. extern const char _sPrinterMmuName[] PROGMEM;
  12. // Firmware version
  13. #define FW_MAJOR 3
  14. #define FW_MINOR 13
  15. #define FW_REVISION 0
  16. #define FW_FLAVOR ALPHA //uncomment if DEBUG, DEVEL, ALPHA, BETA or RC
  17. #define FW_FLAVERSION 1 //uncomment if FW_FLAVOR is defined and versioning is needed. Limited to max 8.
  18. #ifndef FW_FLAVOR
  19. #define FW_VERSION STR(FW_MAJOR) "." STR(FW_MINOR) "." STR(FW_REVISION)
  20. #else
  21. #define FW_VERSION STR(FW_MAJOR) "." STR(FW_MINOR) "." STR(FW_REVISION) "-" STR(FW_FLAVOR) "" STR(FW_FLAVERSION)
  22. #endif
  23. #define FW_COMMIT_NR 6054
  24. // FW_VERSION_UNKNOWN means this is an unofficial build.
  25. // The firmware should only be checked into github with this symbol.
  26. #define FW_DEV_VERSION FW_VERSION_UNKNOWN
  27. #define FW_REPOSITORY "Unknown"
  28. #define FW_VERSION_FULL FW_VERSION "-" STR(FW_COMMIT_NR)
  29. // G-code language level
  30. #define GCODE_LEVEL 1
  31. // Debug version has debugging enabled (the symbol DEBUG_BUILD is set).
  32. // The debug build may be a bit slower than the non-debug build, therefore the debug build should
  33. // not be shipped to a customer.
  34. #define FW_VERSION_DEBUG 6
  35. // This is a development build. A development build is either built from an unofficial git repository,
  36. // or from an unofficial branch, or it does not have a label set. Only the build server should set this build type.
  37. #define FW_VERSION_DEVEL 5
  38. // This is an alpha release. Only the build server should set this build type.
  39. #define FW_VERSION_ALPHA 4
  40. // This is a beta release. Only the build server should set this build type.
  41. #define FW_VERSION_BETA 3
  42. // This is a release candidate build. Only the build server should set this build type.
  43. #define FW_VERSION_RC 2
  44. // This is a final release. Only the build server should set this build type.
  45. #define FW_VERSION_GOLD 1
  46. // This is an unofficial build. The firmware should only be checked into github with this symbol,
  47. // the build server shall never produce builds with this build type.
  48. #define FW_VERSION_UNKNOWN 0
  49. #if FW_DEV_VERSION == FW_VERSION_DEBUG
  50. #define DEBUG_BUILD
  51. #else
  52. #undef DEBUG_BUILD
  53. #endif
  54. #ifndef SOURCE_DATE_EPOCH
  55. #define SOURCE_DATE_EPOCH __DATE__
  56. #endif
  57. #ifndef SOURCE_TIME_EPOCH
  58. #define SOURCE_TIME_EPOCH __TIME__
  59. #endif
  60. #include "Configuration_var.h"
  61. #define FW_PRUSA3D_MAGIC "PRUSA3DFW"
  62. #define FW_PRUSA3D_MAGIC_LEN 10
  63. #include "eeprom.h"
  64. // This configuration file contains the basic settings.
  65. // Advanced settings can be found in Configuration_adv.h
  66. // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
  67. // User-specified version info of this build to display in [Pronterface, etc] terminal window during
  68. // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
  69. // build by the user have been successfully uploaded into firmware.
  70. #define STRING_VERSION_CONFIG_H SOURCE_DATE_EPOCH " " SOURCE_TIME_EPOCH // build date and time
  71. #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
  72. // SERIAL_PORT selects which serial port should be used for communication with the host.
  73. // This allows the connection of wireless adapters (for instance) to non-default port pins.
  74. // Serial port 0 is still used by the Arduino bootloader regardless of this setting.
  75. #define SERIAL_PORT 0
  76. // This determines the communication speed of the printer
  77. #define BAUDRATE 115200
  78. // This enables the serial port associated to the Bluetooth interface
  79. //#define BTENABLED // Enable BT interface on AT90USB devices
  80. // The following define selects which electronics board you have.
  81. // Please choose the name from boards.h that matches your setup
  82. // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
  83. // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
  84. // #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
  85. // This defines the number of extruders
  86. #define EXTRUDERS 1
  87. //// The following define selects which power supply you have. Please choose the one that matches your setup
  88. // 1 = ATX
  89. // 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
  90. #define POWER_SUPPLY 1
  91. // Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
  92. // #define PS_DEFAULT_OFF
  93. // Actual temperature must be close to target for this long before M109 returns success
  94. #define TEMP_RESIDENCY_TIME 3 // (seconds)
  95. #define TEMP_HYSTERESIS 5 // (degC) range of +/- temperatures considered "close" to the target one
  96. #define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
  97. // If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
  98. // average current. The value should be an integer and the heat bed will be turned on for 1 interval of
  99. // HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
  100. //#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
  101. // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
  102. //#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
  103. //#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
  104. // PID settings:
  105. // Comment the following line to disable PID and enable bang-bang.
  106. #define PIDTEMP
  107. #define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
  108. #define PID_MAX BANG_MAX // limits current to nozzle while PID is active; 255=full current
  109. #ifdef PIDTEMP
  110. //#define PID_DEBUG // Sends debug data to the serial port.
  111. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
  112. //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
  113. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
  114. #define PID_K1 0.95 //smoothing factor within the PID
  115. #define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
  116. // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
  117. // Ultimaker
  118. // MakerGear
  119. // #define DEFAULT_Kp 7.0
  120. // #define DEFAULT_Ki 0.1
  121. // #define DEFAULT_Kd 12
  122. // Mendel Parts V9 on 12V
  123. // #define DEFAULT_Kp 63.0
  124. // #define DEFAULT_Ki 2.25
  125. // #define DEFAULT_Kd 440
  126. #endif // PIDTEMP
  127. //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
  128. //can be software-disabled for whatever purposes by
  129. #define PREVENT_DANGEROUS_EXTRUDE
  130. //if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
  131. #define PREVENT_LENGTHY_EXTRUDE
  132. #ifdef DEBUG_DISABLE_PREVENT_EXTRUDER
  133. #undef PREVENT_DANGEROUS_EXTRUDE
  134. #undef PREVENT_LENGTHY_EXTRUDE
  135. #endif //DEBUG_DISABLE_PREVENT_EXTRUDER
  136. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
  137. /*================== Thermal Runaway Protection ==============================
  138. This is a feature to protect your printer from burn up in flames if it has
  139. a thermistor coming off place (this happened to a friend of mine recently and
  140. motivated me writing this feature).
  141. The issue: If a thermistor come off, it will read a lower temperature than actual.
  142. The system will turn the heater on forever, burning up the filament and anything
  143. else around.
  144. After the temperature reaches the target for the first time, this feature will
  145. start measuring for how long the current temperature stays below the target
  146. minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
  147. If it stays longer than _PERIOD, it means the thermistor temperature
  148. cannot catch up with the target, so something *may be* wrong. Then, to be on the
  149. safe side, the system will he halt.
  150. Bear in mind the count down will just start AFTER the first time the
  151. thermistor temperature is over the target, so you will have no problem if
  152. your extruder heater takes 2 minutes to hit the target on heating.
  153. */
  154. // If you want to enable this feature for all your extruder heaters,
  155. // uncomment the 2 defines below:
  156. // Parameters for all extruder heaters
  157. //#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
  158. //#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
  159. // If you want to enable this feature for your bed heater,
  160. // uncomment the 2 defines below:
  161. // Parameters for the bed heater
  162. //#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
  163. //#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
  164. //===========================================================================
  165. //===========================================================================
  166. //=============================Mechanical Settings===========================
  167. //===========================================================================
  168. // Uncomment the following line to enable CoreXY kinematics
  169. // #define COREXY
  170. // coarse Endstop Settings
  171. #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
  172. #ifndef ENDSTOPPULLUPS
  173. // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
  174. // #define ENDSTOPPULLUP_XMAX
  175. // #define ENDSTOPPULLUP_YMAX
  176. // #define ENDSTOPPULLUP_ZMAX
  177. // #define ENDSTOPPULLUP_XMIN
  178. // #define ENDSTOPPULLUP_YMIN
  179. // #define ENDSTOPPULLUP_ZMIN
  180. #endif
  181. #ifdef ENDSTOPPULLUPS
  182. #define ENDSTOPPULLUP_XMAX
  183. #define ENDSTOPPULLUP_YMAX
  184. #define ENDSTOPPULLUP_ZMAX
  185. #define ENDSTOPPULLUP_XMIN
  186. #define ENDSTOPPULLUP_YMIN
  187. #define ENDSTOPPULLUP_ZMIN
  188. #endif
  189. // The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
  190. #define X_MAX_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  191. #define Y_MAX_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
  192. #define Z_MAX_ENDSTOP_INVERTING 1 // set to 1 to invert the logic of the endstop.
  193. //#define DISABLE_MAX_ENDSTOPS
  194. //#define DISABLE_MIN_ENDSTOPS
  195. // Disable max endstops for compatibility with endstop checking routine
  196. #if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
  197. #define DISABLE_MAX_ENDSTOPS
  198. #endif
  199. // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
  200. #define X_ENABLE_ON 0
  201. #define Y_ENABLE_ON 0
  202. #define Z_ENABLE_ON 0
  203. #define E_ENABLE_ON 0 // For all extruders
  204. // Disables axis when it's not being used.
  205. #define DISABLE_X 0
  206. #define DISABLE_Y 0
  207. #define DISABLE_Z 0
  208. #define DISABLE_E 0// For all extruders
  209. #define DISABLE_INACTIVE_EXTRUDER 1 //disable only inactive extruders and keep active extruder enabled
  210. // ENDSTOP SETTINGS:
  211. // Sets direction of endstops when homing; 1=MAX, -1=MIN
  212. #define X_HOME_DIR -1
  213. #define Y_HOME_DIR -1
  214. #define Z_HOME_DIR -1
  215. #ifdef DEBUG_DISABLE_SWLIMITS
  216. #define min_software_endstops 0
  217. #define max_software_endstops 0
  218. #else
  219. #define min_software_endstops 1 // If true, axis won't move to coordinates less than HOME_POS.
  220. #define max_software_endstops 1 // If true, axis won't move to coordinates greater than the defined lengths below.
  221. #endif //DEBUG_DISABLE_SWLIMITS
  222. #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
  223. #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
  224. #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
  225. #define Z_HEIGHT_HIDE_LIVE_ADJUST_MENU 2.0f
  226. #define HOME_Z_SEARCH_THRESHOLD 0.15f // Threshold of the Z height in calibration
  227. //============================= Bed Auto Leveling ===========================
  228. //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
  229. #define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
  230. #ifdef ENABLE_AUTO_BED_LEVELING
  231. // There are 2 different ways to pick the X and Y locations to probe:
  232. // - "grid" mode
  233. // Probe every point in a rectangular grid
  234. // You must specify the rectangle, and the density of sample points
  235. // This mode is preferred because there are more measurements.
  236. // It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
  237. // - "3-point" mode
  238. // Probe 3 arbitrary points on the bed (that aren't colinear)
  239. // You must specify the X & Y coordinates of all 3 points
  240. #define AUTO_BED_LEVELING_GRID
  241. // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
  242. // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
  243. // and least squares solution is calculated
  244. // Note: this feature occupies 10'206 byte
  245. #ifdef AUTO_BED_LEVELING_GRID
  246. // set the rectangle in which to probe
  247. #define LEFT_PROBE_BED_POSITION 15
  248. #define RIGHT_PROBE_BED_POSITION 170
  249. #define BACK_PROBE_BED_POSITION 180
  250. #define FRONT_PROBE_BED_POSITION 20
  251. // set the number of grid points per dimension
  252. // I wouldn't see a reason to go above 3 (=9 probing points on the bed)
  253. #define AUTO_BED_LEVELING_GRID_POINTS 2
  254. #else // not AUTO_BED_LEVELING_GRID
  255. // with no grid, just probe 3 arbitrary points. A simple cross-product
  256. // is used to esimate the plane of the print bed
  257. #define ABL_PROBE_PT_1_X 15
  258. #define ABL_PROBE_PT_1_Y 180
  259. #define ABL_PROBE_PT_2_X 15
  260. #define ABL_PROBE_PT_2_Y 20
  261. #define ABL_PROBE_PT_3_X 170
  262. #define ABL_PROBE_PT_3_Y 20
  263. #endif // AUTO_BED_LEVELING_GRID
  264. // these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
  265. // X and Y offsets must be integers
  266. #define X_PROBE_OFFSET_FROM_EXTRUDER -25
  267. #define Y_PROBE_OFFSET_FROM_EXTRUDER -29
  268. #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
  269. #define Z_RAISE_BEFORE_HOMING 5 // (in mm) Raise Z before homing (G28) for Probe Clearance.
  270. // Be sure you have this distance over your Z_MAX_POS in case
  271. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min
  272. #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
  273. #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
  274. //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
  275. //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
  276. //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
  277. //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
  278. // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
  279. // #define PROBE_SERVO_DEACTIVATION_DELAY 300
  280. //If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
  281. //it is highly recommended you let this Z_SAFE_HOMING enabled!
  282. //#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area.
  283. // When defined, it will:
  284. // - Allow Z homing only after X and Y homing AND stepper drivers still enabled
  285. // - If stepper drivers timeout, it will need X and Y homing again before Z homing
  286. // - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
  287. // - Block Z homing only when the probe is outside bed area.
  288. #ifdef Z_SAFE_HOMING
  289. #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28)
  290. #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28)
  291. #endif
  292. #ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
  293. #if X_PROBE_OFFSET_FROM_EXTRUDER < 0
  294. #if (-(X_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
  295. #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
  296. #endif
  297. #else
  298. #if ((X_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
  299. #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
  300. #endif
  301. #endif
  302. #if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
  303. #if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
  304. #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
  305. #endif
  306. #else
  307. #if ((Y_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
  308. #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
  309. #endif
  310. #endif
  311. #endif
  312. #endif // ENABLE_AUTO_BED_LEVELING
  313. // The position of the homing switches
  314. //#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
  315. //#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
  316. //Manual homing switch locations:
  317. // For deltabots this means top and center of the Cartesian print volume.
  318. // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
  319. // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
  320. // For the other hotends it is their distance from the extruder 0 hotend.
  321. // #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
  322. // #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
  323. // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
  324. #define DEFAULT_XJERK 10 // (mm/sec)
  325. #define DEFAULT_YJERK 10 // (mm/sec)
  326. #define DEFAULT_ZJERK 0.4 // (mm/sec)
  327. #define DEFAULT_EJERK 4.5 // (mm/sec)
  328. //===========================================================================
  329. //=============================Additional Features===========================
  330. //===========================================================================
  331. // Custom M code points
  332. #define CUSTOM_M_CODES
  333. #ifdef CUSTOM_M_CODES
  334. #ifdef ENABLE_AUTO_BED_LEVELING
  335. #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
  336. #define Z_PROBE_OFFSET_RANGE_MIN -15
  337. #define Z_PROBE_OFFSET_RANGE_MAX -5
  338. #endif // ENABLE_AUTO_BED_LEVELING
  339. #endif // CUSTOM_M_CODES
  340. // Host Keepalive
  341. //
  342. // When enabled Marlin will send a busy status message to the host
  343. // every couple of seconds when it can't accept commands.
  344. //
  345. #ifndef HEATBED_ANALYSIS
  346. #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
  347. #endif //HEATBED_ANALYSIS
  348. #define HOST_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
  349. //LCD and SD support
  350. #define SDSUPPORT // Enable SD Card Support in Hardware Console
  351. //#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
  352. #define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
  353. #define ENCODER_PULSES_PER_STEP 4 // Increase if you have a high resolution encoder
  354. //#define ENCODER_STEPS_PER_MENU_ITEM 1 // Set according to ENCODER_PULSES_PER_STEP or your liking
  355. // The RepRapDiscount Smart Controller (white PCB)
  356. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
  357. #define REPRAP_DISCOUNT_SMART_CONTROLLER
  358. #define SDSUPPORT
  359. #define LCD_WIDTH 20
  360. #define LCD_HEIGHT 4
  361. // Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
  362. //#define FAST_PWM_FAN
  363. // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
  364. // which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
  365. // is too low, you should also increment SOFT_PWM_SCALE.
  366. #define FAN_SOFT_PWM
  367. #define FAN_SOFT_PWM_BITS 4 //PWM bit resolution = 4bits, freq = 62.5Hz
  368. // Bed soft pwm
  369. #define HEATER_BED_SOFT_PWM_BITS 5 //PWM bit resolution = 5bits, freq = 31.25Hz
  370. // Incrementing this by 1 will double the software PWM frequency,
  371. // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
  372. // However, control resolution will be halved for each increment;
  373. // at zero value, there are 128 effective control positions.
  374. #define SOFT_PWM_SCALE 0
  375. // M240 Triggers a camera by emulating a Canon RC-1 Remote
  376. // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
  377. // #define PHOTOGRAPH_PIN 23
  378. // SF send wrong arc g-codes when using Arc Point as fillet procedure
  379. //#define SF_ARC_FIX
  380. //define BlinkM/CyzRgb Support
  381. //#define BLINKM
  382. /*********************************************************************\
  383. * R/C SERVO support
  384. * Sponsored by TrinityLabs, Reworked by codexmas
  385. **********************************************************************/
  386. // Number of servos
  387. //
  388. // If you select a configuration below, this will receive a default value and does not need to be set manually
  389. // set it manually if you have more servos than extruders and wish to manually control some
  390. // leaving it undefined or defining as 0 will disable the servo subsystem
  391. // If unsure, leave commented / disabled
  392. //
  393. //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
  394. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm). Used by the volumetric extrusion.
  395. // Calibration status of the machine, to be stored into the EEPROM,
  396. // (unsigned char*)EEPROM_CALIBRATION_STATUS
  397. enum CalibrationStatus
  398. {
  399. // Freshly assembled, needs to peform a self-test and the XYZ calibration.
  400. CALIBRATION_STATUS_ASSEMBLED = 255,
  401. // For the wizard: self test has been performed, now the XYZ calibration is needed.
  402. CALIBRATION_STATUS_XYZ_CALIBRATION = 250,
  403. // For the wizard: factory assembled, needs to run Z calibration.
  404. CALIBRATION_STATUS_Z_CALIBRATION = 240,
  405. #ifdef TEMP_MODEL
  406. // The XYZ calibration has been performed, needs to run Temp model calibration.
  407. CALIBRATION_STATUS_TEMP_MODEL_CALIBRATION = 235,
  408. #endif //TEMP_MODEL
  409. // The XYZ calibration AND OR Temp model calibration has been performed, now it remains to run the V2Calibration.gcode.
  410. CALIBRATION_STATUS_LIVE_ADJUST = 230,
  411. // Calibrated, ready to print.
  412. CALIBRATION_STATUS_CALIBRATED = 1,
  413. // Legacy: resetted by issuing a G86 G-code.
  414. // This value can only be expected after an upgrade from the initial MK2 firmware releases.
  415. // Currently the G86 sets the calibration status to
  416. CALIBRATION_STATUS_UNKNOWN = 0,
  417. };
  418. // Try to maintain a minimum distance from the bed even when Z is
  419. // unknown when doing the following operations
  420. #define MIN_Z_FOR_LOAD 50 // lcd filament loading or autoload
  421. #define MIN_Z_FOR_UNLOAD 50 // lcd filament unloading
  422. #define MIN_Z_FOR_SWAP 27 // filament change (including M600)
  423. #define MIN_Z_FOR_PREHEAT 10 // lcd preheat
  424. #include "Configuration_adv.h"
  425. #include "thermistortables.h"
  426. #endif //__CONFIGURATION_H