PrusaFirmware/Firmware/tmc2130.h

#ifndef TMC2130_H
#define TMC2130_H

extern uint8_t tmc2130_cs[4];

//mode
extern uint8_t tmc2130_mode;
//holding and running currents
extern uint8_t tmc2130_current_h[4];
extern uint8_t tmc2130_current_r[4];
//flags for axis stall detection
extern uint8_t tmc2130_axis_stalled[4];

extern uint8_t tmc2130_sg_thr[4];

extern bool tmc2130_sg_stop_on_crash;
extern bool tmc2130_sg_crash;

extern uint8_t tmc2130_sg_meassure;
extern uint16_t tmc2130_sg_meassure_cnt;
extern uint32_t tmc2130_sg_meassure_val;

#define TMC2130_MODE_NORMAL 0
#define TMC2130_MODE_SILENT 1

//initialize tmc2130
extern void tmc2130_init();
//check diag pins (called from stepper isr)
extern void tmc2130_st_isr(uint8_t last_step_mask);
//update stall guard (called from st_synchronize inside the loop)
extern bool tmc2130_update_sg();
//temperature watching (called from )
extern void tmc2130_check_overtemp();
//enter homing (called from homeaxis before homing starts)
extern void tmc2130_home_enter(uint8_t axes_mask);
//exit homing (called from homeaxis after homing ends)
extern void tmc2130_home_exit();
//restart homing (called from homeaxis befor move)
extern void tmc2130_home_restart(uint8_t axis);

//start stallguard meassuring for single axis
extern void tmc2130_sg_meassure_start(uint8_t axis);
//stop current stallguard meassuring and report result
extern uint16_t tmc2130_sg_meassure_stop();


//set holding current for any axis (M911)
extern void tmc2130_set_current_h(uint8_t axis, uint8_t current);
//set running current for any axis (M912)
extern void tmc2130_set_current_r(uint8_t axis, uint8_t current);
//print currents (M913)
extern void tmc2130_print_currents();

//set PWM_AMPL for any axis (M917)
extern void tmc2130_set_pwm_ampl(uint8_t axis, uint8_t pwm_ampl);
//set PWM_GRAD for any axis (M918)
extern void tmc2130_set_pwm_grad(uint8_t axis, uint8_t pwm_ampl);


extern uint16_t tmc2130_rd_MSCNT(uint8_t cs);

extern void tmc2130_home_pause(uint8_t axis);
extern void tmc2130_home_resume(uint8_t axis);
extern bool tmc2130_wait_standstill_xy(int timeout);

extern void tmc2130_eeprom_load_config();
extern void tmc2130_eeprom_save_config();

#pragma pack(push)
#pragma pack(1)
struct
{
	uint8_t mres:5;             // mres       - byte 0, bit 0..4     microstep resolution
	uint8_t reserved_0_0:2;     // reserved   - byte 0, bit 5..6
	uint8_t intpol:1;           // intpol     - byte 0, bit 7        linear interpolation to 255 usteps
	uint8_t pwm_ampl:8;         // pwm_ampl   - byte 1, bit 0..7     pwm amplitude for silent mode
	uint8_t pwm_grad:4;         // pwm_grad   - byte 2, bit 0..3     pwm gradient for silent mode
	uint8_t pwm_freq:2;         // pwm_freq   - byte 2, bit 4..5     pwm frequency for silent mode
	uint8_t reserved_2_0:2;     // reserved   - byte 2, bit 6..7
	uint16_t tcoolthrs:16;      // tcoolthrs  - byte 3..4            coolstep threshold / middle sensitivity
	int8_t  sg_thrs:8;          // sg_thrs    - byte 5, bit 0..7     stallguard sensitivity in high power / middle sensitivity
	int8_t  current_h:6;        // current_h  - byte 6, bit 0..5     holding current for high power mode
	uint8_t reserved_6_0:2;     // reserved   - byte 6, bit 6..7
	int8_t  current_r:6;        // current_r  - byte 7, bit 0..5     running current for high power mode
	uint8_t reserved_7_0:2;     // reserved   - byte 7, bit 6..7
	int8_t  home_sg_thrs:8;     // sg_thrs    - byte 8, bit 0..7     stallguard sensitivity for homing
	int8_t  home_current:6;     // current_r  - byte 9, bit 0..5     running current for homing
	uint8_t reserved_9_0:2;     // reserved   - byte 9, bit 6..7
	int8_t  home_dtcoolthrs:8;  // dtcoolthrs - byte 10, bit 0..7    delta tcoolthrs for homing
	int8_t  dtcoolthrs_low:8;   // dtcoolthrs - byte 11, bit 0..7    delta tcoolthrs for low sensitivity (based on value for middle sensitivity)
	int8_t  dtcoolthrs_high:8;  // dtcoolthrs - byte 12, bit 0..7    delta tcoolthrs for high sensitivity (based on value for middle sensitivity)
	int8_t  sg_thrs_low:8;      // sg_thrs    - byte 13, bit 0..7    stallguard sensitivity in high power / low sensitivity
	int8_t  sg_thrs_high:8;     // sg_thrs    - byte 14, bit 0..7    stallguard sensitivity in high power / high sensitivity
} tmc2130_axis_config;
#pragma pack(pop)

#endif //TMC2130_H