Use uint8_t when using axis enum

Saves 76 bytes of flash memory

Firmware/Marlin.h

@@ -294,9 +294,9 @@ extern int8_t lcd_change_fil_state;
 extern float default_retraction;
 
 #ifdef TMC2130
-void homeaxis(int axis, uint8_t cnt = 1, uint8_t* pstep = 0);
+void homeaxis(uint8_t axis, uint8_t cnt = 1, uint8_t* pstep = 0);
 #else
-void homeaxis(int axis, uint8_t cnt = 1);
+void homeaxis(uint8_t axis, uint8_t cnt = 1);
 #endif //TMC2130
 
 

Firmware/Marlin_main.cpp

@@ -2034,9 +2034,9 @@ DEFINE_PGM_READ_ANY(signed char, byte);
 #define XYZ_CONSTS_FROM_CONFIG(type, array, CONFIG) \
 static const PROGMEM type array##_P[3] =        \
     { X_##CONFIG, Y_##CONFIG, Z_##CONFIG };     \
-static inline type array(int axis)              \
+static inline type array(uint8_t axis)              \
     { return pgm_read_any(&array##_P[axis]); }  \
-type array##_ext(int axis)                      \
+type array##_ext(uint8_t axis)                      \
     { return pgm_read_any(&array##_P[axis]); }
 
 XYZ_CONSTS_FROM_CONFIG(float, base_min_pos,    MIN_POS);
@@ -2046,7 +2046,7 @@ XYZ_CONSTS_FROM_CONFIG(float, max_length,      MAX_LENGTH);
 XYZ_CONSTS_FROM_CONFIG(float, home_retract_mm, HOME_RETRACT_MM);
 XYZ_CONSTS_FROM_CONFIG(signed char, home_dir,  HOME_DIR);
 
-static void axis_is_at_home(int axis) {
+static void axis_is_at_home(uint8_t axis) {
   current_position[axis] = base_home_pos(axis) + cs.add_homing[axis];
   min_pos[axis] =          base_min_pos(axis) + cs.add_homing[axis];
   max_pos[axis] =          base_max_pos(axis) + cs.add_homing[axis];
@@ -2362,9 +2362,9 @@ static void check_Z_crash(void)
 #endif //TMC2130
 
 #ifdef TMC2130
-void homeaxis(int axis, uint8_t cnt, uint8_t* pstep)
+void homeaxis(uint8_t axis, uint8_t cnt, uint8_t* pstep)
 #else
-void homeaxis(int axis, uint8_t cnt)
+void homeaxis(uint8_t axis, uint8_t cnt)
 #endif //TMC2130
 {
 	bool endstops_enabled  = enable_endstops(true); //RP: endstops should be allways enabled durring homing
@@ -2835,7 +2835,7 @@ static void gcode_G28(bool home_x_axis, long home_x_value, bool home_y_axis, lon
       {
         current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0;
 
-        int x_axis_home_dir = home_dir(X_AXIS);
+        uint8_t x_axis_home_dir = home_dir(X_AXIS);
 
         plan_set_position_curposXYZE();
         destination[X_AXIS] = 1.5 * max_length(X_AXIS) * x_axis_home_dir;destination[Y_AXIS] = 1.5 * max_length(Y_AXIS) * home_dir(Y_AXIS);

Firmware/ultralcd.cpp

@@ -161,8 +161,8 @@ static void lcd_belttest_v();
 static void lcd_selftest_v();
 
 #ifdef TMC2130
-static void reset_crash_det(unsigned char axis);
-static bool lcd_selfcheck_axis_sg(unsigned char axis);
+static void reset_crash_det(uint8_t axis);
+static bool lcd_selfcheck_axis_sg(uint8_t axis);
 #else
 static bool lcd_selfcheck_axis(int _axis, int _travel);
 static bool lcd_selfcheck_pulleys(int axis);
@@ -7706,14 +7706,14 @@ bool lcd_selftest()
 
 #ifdef TMC2130
 
-static void reset_crash_det(unsigned char axis) {
+static void reset_crash_det(uint8_t axis) {
 	current_position[axis] += 10;
 	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60);
 	st_synchronize();
 	if (eeprom_read_byte((uint8_t*)EEPROM_CRASH_DET)) tmc2130_sg_stop_on_crash = true;
 }
 
-static bool lcd_selfcheck_axis_sg(unsigned char axis) {
+static bool lcd_selfcheck_axis_sg(uint8_t axis) {
 // each axis length is measured twice	
 	float axis_length, current_position_init, current_position_final;
 	float measured_axis_length[2];