Merge branch 'MK2' of https://github.com/Prusa3D/Prusa-Firmware into MK2

Firmware/Configuration.h

@@ -31,6 +31,7 @@
 // The offsets are saved as 16bit signed int, scaled to tenths of microns.
 #define EEPROM_BED_CALIBRATION_Z_JITTER   (EEPROM_BED_CALIBRATION_VEC_Y-2*8)
 
+#define EEPROM_FARM_MODE (EEPROM_BED_CALIBRATION_Z_JITTER-4)
 
 // Currently running firmware, each digit stored as uint16_t.
 // The flavor differentiates a dev, alpha, beta, release candidate or a release version.

Firmware/Marlin_main.cpp

@@ -255,7 +255,7 @@ int extruder_multiply[EXTRUDERS] = {100
 };
 
 bool is_usb_printing = false;
-bool _doMeshL = false;
+
 unsigned int  usb_printing_counter;
 
 int lcd_change_fil_state = 0;
@@ -933,22 +933,58 @@ void setup()
   world2machine_reset();
 
   lcd_init();
-  if(!READ(BTN_ENC) ){
-    _delay_ms(1000);
-    if(!READ(BTN_ENC) ){
-    SET_OUTPUT(BEEPER);
+  if (!READ(BTN_ENC))
+  {
+	  _delay_ms(1000);
+	  if (!READ(BTN_ENC))
+	  {
+		  SET_OUTPUT(BEEPER);
+		  WRITE(BEEPER, HIGH);
 
-    WRITE(BEEPER,HIGH);
-    
-    lcd_force_language_selection();
-    while(!READ(BTN_ENC));
+		  lcd_force_language_selection();
+		  farm_no = 0;
+		  EEPROM_save_B(EEPROM_FARM_MODE, &farm_no);
+		  farm_mode = false;
 
-    WRITE(BEEPER,LOW);
+		  while (!READ(BTN_ENC));
 
-    }
-  }else{
-    _delay_ms(1000);  // wait 1sec to display the splash screen
+		  WRITE(BEEPER, LOW);
+
+#ifdef MESH_BED_LEVELING
+		  _delay_ms(2000);
+
+		  if (!READ(BTN_ENC))
+		  {
+			  WRITE(BEEPER, HIGH);
+			  _delay_ms(100);
+			  WRITE(BEEPER, LOW);
+			  _delay_ms(200);
+			  WRITE(BEEPER, HIGH);
+			  _delay_ms(100);
+			  WRITE(BEEPER, LOW);
+
+			  int _z = 0;
+			  eeprom_write_byte((unsigned char*)EEPROM_BABYSTEP_Z_SET, 0x01);
+			  EEPROM_save_B(EEPROM_BABYSTEP_X, &_z);
+			  EEPROM_save_B(EEPROM_BABYSTEP_Y, &_z);
+			  EEPROM_save_B(EEPROM_BABYSTEP_Z, &_z);
+		  }
+		  else
+		  {
+
+			  WRITE(BEEPER, HIGH);
+			  _delay_ms(100);
+			  WRITE(BEEPER, LOW);
+		  }
+#endif // mesh
+
+	  }
   }
+  else
+  {
+	  _delay_ms(1000);  // wait 1sec to display the splash screen
+  }
+
   
 
   #if defined(CONTROLLERFAN_PIN) && CONTROLLERFAN_PIN > -1
@@ -964,6 +1000,20 @@ void setup()
   enable_z();
 #endif
 
+  EEPROM_read_B(EEPROM_FARM_MODE, &farm_no);
+  if (farm_no > 0)
+  {
+	  farm_mode = true;
+	  farm_no = farm_no;
+	  prusa_statistics(8);
+  }
+  else
+  {
+	  farm_mode = false;
+	  farm_no = 0;
+  }
+
+
   // In the future, somewhere here would one compare the current firmware version against the firmware version stored in the EEPROM.
   // If they differ, an update procedure may need to be performed. At the end of this block, the current firmware version
   // is being written into the EEPROM, so the update procedure will be triggered only once.
@@ -1217,6 +1267,12 @@ void get_command()
         card.printingHasFinished();
         card.checkautostart(true);
 
+		if (farm_mode)
+		{
+			prusa_statistics(6);
+			lcd_commands_type = 4;
+		}
+
       }
       if(serial_char=='#')
         stop_buffering=true;
@@ -1833,7 +1889,7 @@ void process_commands()
       plan_bed_level_matrix.set_to_identity();  //Reset the plane ("erase" all leveling data)
 #endif //ENABLE_AUTO_BED_LEVELING
             
-	      _doMeshL = false;
+	      
         // For mesh bed leveling deactivate the matrix temporarily
         #ifdef MESH_BED_LEVELING
             mbl.active = 0;
@@ -1905,11 +1961,7 @@ void process_commands()
       }
       #endif /* QUICK_HOME */
 
-	  if (home_all_axis)
-	  {
-		  _doMeshL = true;
-	  }
-
+	 
       if((home_all_axis) || (code_seen(axis_codes[X_AXIS])))
         homeaxis(X_AXIS);
 
@@ -1955,7 +2007,6 @@ void process_commands()
               enable_endstops(true);
               endstops_hit_on_purpose();
               homeaxis(Z_AXIS);
-  		        _doMeshL = true;
             #else // MESH_BED_LEVELING
               homeaxis(Z_AXIS);
             #endif // MESH_BED_LEVELING
@@ -2042,22 +2093,21 @@ void process_commands()
     world2machine_update_current();
 
 #ifdef MESH_BED_LEVELING
-	  if (code_seen('W'))
-	  {
-		  _doMeshL = false;
-      SERIAL_ECHOLN("G80 disabled");
-	  }
-
-	  if ( _doMeshL)
-	  {
-		  st_synchronize();
-      // Push the commands to the front of the message queue in the reverse order!
-      // There shall be always enough space reserved for these commands.
-		  // enquecommand_front_P((PSTR("G80")));
-      goto case_G80;
+	if (code_seen(axis_codes[X_AXIS]) || code_seen(axis_codes[Y_AXIS]) || code_seen('W') || code_seen(axis_codes[Z_AXIS]))
+		{
+		}
+	else
+		{
+			st_synchronize();
+			// Push the commands to the front of the message queue in the reverse order!
+			// There shall be always enough space reserved for these commands.
+			// enquecommand_front_P((PSTR("G80")));
+			goto case_G80;
 	  }
 #endif
 
+	  if (farm_mode) { prusa_statistics(20); };
+
       break;
 
 #ifdef ENABLE_AUTO_BED_LEVELING
@@ -2502,6 +2552,25 @@ void process_commands()
         }
       }
       break;
+
+	case 98:
+		farm_no = 21;
+		EEPROM_save_B(EEPROM_FARM_MODE, &farm_no);
+		farm_mode = true;
+		break;
+
+	case 99:
+		farm_no = 0;
+		EEPROM_save_B(EEPROM_FARM_MODE, &farm_no);
+		farm_mode = false;
+		break;
+
+
+
+
+
+
+
     }
   } // end if(code_seen('G'))
 
@@ -3196,6 +3265,7 @@ Sigma_Exit:
       }
       LCD_MESSAGERPGM(MSG_HEATING);
 	  heating_status = 1;
+	  if (farm_mode) { prusa_statistics(1); };
 
 #ifdef AUTOTEMP
         autotemp_enabled=false;
@@ -3274,6 +3344,7 @@ Sigma_Exit:
         }
         LCD_MESSAGERPGM(MSG_HEATING_COMPLETE);
 		heating_status = 2;
+		if (farm_mode) { prusa_statistics(2); };
         
         starttime=millis();
         previous_millis_cmd = millis();
@@ -3283,7 +3354,7 @@ Sigma_Exit:
     #if defined(TEMP_BED_PIN) && TEMP_BED_PIN > -1
         LCD_MESSAGERPGM(MSG_BED_HEATING);
 		heating_status = 3;
-
+		if (farm_mode) { prusa_statistics(1); };
         if (code_seen('S')) 
 		{
           setTargetBed(code_value());

Firmware/ultralcd.cpp

@@ -39,6 +39,10 @@ int8_t SilentModeMenu = 0;
 int lcd_commands_type=0;
 int lcd_commands_step=0;
 bool isPrintPaused = false;
+bool farm_mode = false;
+int farm_no = 0;
+int farm_timer = 30;
+int farm_status = 0;
 
 bool menuExiting = false;
 
@@ -114,6 +118,11 @@ static void lcd_control_temperature_preheat_abs_settings_menu();
 static void lcd_control_motion_menu();
 static void lcd_control_volumetric_menu();
 
+static void prusa_stat_printerstatus(int _status);
+static void prusa_stat_temperatures();
+static void prusa_stat_printinfo();
+static void lcd_farm_no();
+
 #ifdef DOGLCD
 static void lcd_set_contrast();
 #endif
@@ -340,7 +349,27 @@ static void lcd_status_screen()
     lcd_implementation_status_screen();
     //lcd_implementation_clear();
 
-
+	if (farm_mode)
+	{
+		farm_timer--;
+		if (farm_timer < 1)
+		{
+			farm_timer = 90;
+			prusa_statistics(0);
+		}
+		switch (farm_timer)
+		{
+		case 45:
+			prusa_statistics(21);
+			break;
+		case 10:
+			if (IS_SD_PRINTING)
+			{
+				prusa_statistics(20);
+			}
+			break;
+		}
+	}
 
 
 
@@ -504,6 +533,7 @@ void lcd_commands()
 		if (lcd_commands_step == 4 && !blocks_queued())
 		{
 			enquecommand_P(PSTR("G90"));
+			enquecommand_P(PSTR("M83"));
 			#ifdef X_CANCEL_POS 
 			enquecommand_P(PSTR("G1 X"  STRINGIFY(X_CANCEL_POS) " Y" STRINGIFY(Y_CANCEL_POS) " E0 F7000"));
 			#else
@@ -538,6 +568,46 @@ void lcd_commands()
 		lcd_commands_type = 0;
 	}
 
+	if (lcd_commands_type == 4)   /// farm mode confirm
+	{
+
+		if (lcd_commands_step == 0) { lcd_commands_step = 6; custom_message = true; }
+
+		if (lcd_commands_step == 1 && !blocks_queued())
+		{
+			lcd_confirm_print();
+			lcd_commands_step = 0;
+			lcd_commands_type = 0;
+		}
+		if (lcd_commands_step == 2 && !blocks_queued())
+		{
+			lcd_commands_step = 1;
+		}
+		if (lcd_commands_step == 3 && !blocks_queued())
+		{
+			lcd_commands_step = 2;
+		}
+		if (lcd_commands_step == 4 && !blocks_queued())
+		{
+			enquecommand_P(PSTR("G90"));
+			enquecommand_P(PSTR("G1 X"  STRINGIFY(X_CANCEL_POS) " Y" STRINGIFY(Y_CANCEL_POS) " E0 F7000"));
+			lcd_commands_step = 3;
+		}
+		if (lcd_commands_step == 5 && !blocks_queued())
+		{
+			lcd_commands_step = 4;
+		}
+		if (lcd_commands_step == 6 && !blocks_queued())
+		{
+			enquecommand_P(PSTR("G91"));
+			enquecommand_P(PSTR("G1 Z15 F1500"));
+			st_synchronize();
+			lcd_commands_step = 5;
+		}
+
+	}
+
+
 }
 
 static void lcd_return_to_status() {
@@ -924,7 +994,7 @@ static void lcd_menu_statistics()
 		int _t = (millis() - starttime) / 1000;
 
 		int _h = _t / 3600;
-		int _m = (_t - (_h * 60)) / 60;
+		int _m = (_t - (_h * 3600)) / 60;
 		int _s = _t - ((_h * 3600) + (_m * 60));
 		
 		lcd.setCursor(0, 0);
@@ -1486,6 +1556,148 @@ void lcd_diag_show_end_stops()
     lcd_return_to_status();
 }
 
+
+
+void prusa_statistics(int _message) {
+
+	switch (_message)
+	{
+
+	case 0: // default message
+		if (IS_SD_PRINTING)
+		{
+			SERIAL_ECHO("{");
+			prusa_stat_printerstatus(4);
+			prusa_stat_printinfo();
+			SERIAL_ECHOLN("}");
+		}
+		else
+		{
+			SERIAL_ECHO("{");
+			prusa_stat_printerstatus(1);
+			SERIAL_ECHOLN("}");
+		}
+		break;
+
+	case 1:		// 1 heating
+		farm_status = 2;
+		SERIAL_ECHO("{");
+		prusa_stat_printerstatus(2);
+		SERIAL_ECHOLN("}");
+		farm_timer = 1;
+		break;
+
+	case 2:		// heating done
+		farm_status = 3;
+		SERIAL_ECHO("{");
+		prusa_stat_printerstatus(3);
+		SERIAL_ECHOLN("}");
+		farm_timer = 1;
+
+		if (IS_SD_PRINTING)
+		{
+			farm_status = 4;
+			SERIAL_ECHO("{");
+			prusa_stat_printerstatus(4);
+			SERIAL_ECHOLN("}");
+		}
+		else
+		{
+			SERIAL_ECHO("{");
+			prusa_stat_printerstatus(3);
+			SERIAL_ECHOLN("}");;
+		}
+		farm_timer = 1;
+		break;
+
+	case 3:		// filament change
+
+		break;
+	case 4:		// print succesfull
+		SERIAL_ECHOLN("{[RES:1]}");
+		farm_timer = 2;
+		break;
+	case 5:		// print not succesfull
+		SERIAL_ECHOLN("{[RES:0]}");
+		farm_timer = 2;
+		break;
+	case 6:		// print done
+		SERIAL_ECHOLN("{[PRN:8]}");
+		farm_timer = 2;
+		break;
+	case 7:		// print done - stopped
+		SERIAL_ECHOLN("{[PRN:9]}");
+		farm_timer = 2;
+		break;
+	case 8:		// printer started
+		SERIAL_ECHO("{[PRN:0][PFN:");
+		SERIAL_ECHO(farm_no);
+		SERIAL_ECHOLN("]}");
+		farm_timer = 2;
+		break;
+	case 20:		// echo farm no
+		SERIAL_ECHO("{[PFN:");
+		SERIAL_ECHO(farm_no);
+		SERIAL_ECHOLN("]}");
+		farm_timer = 5;
+		break;
+	case 21: // temperatures
+		SERIAL_ECHO("{");
+		prusa_stat_temperatures();
+		SERIAL_ECHOLN("}");
+		break;
+	case 99:		// heartbeat
+		SERIAL_ECHOLN("{[PRN:99]}");
+		break;
+	}
+
+}
+
+static void prusa_stat_printerstatus(int _status)
+{
+	SERIAL_ECHO("[PRN:");
+	SERIAL_ECHO(_status);
+	SERIAL_ECHO("]");
+}
+
+static void prusa_stat_temperatures()
+{
+	SERIAL_ECHO("[ST0:");
+	SERIAL_ECHO(target_temperature[0]);
+	SERIAL_ECHO("][STB:");
+	SERIAL_ECHO(target_temperature_bed);
+	SERIAL_ECHO("][AT0:");
+	SERIAL_ECHO(current_temperature[0]);
+	SERIAL_ECHO("][ATB:");
+	SERIAL_ECHO(current_temperature_bed);
+	SERIAL_ECHO("]");
+}
+
+static void prusa_stat_printinfo()
+{
+	SERIAL_ECHO("[TFU:");
+	SERIAL_ECHO(total_filament_used);
+	SERIAL_ECHO("][PCD:");
+	SERIAL_ECHO(itostr3(card.percentDone()));
+	SERIAL_ECHO("][FEM:");
+	SERIAL_ECHO(itostr3(feedmultiply));
+	SERIAL_ECHO("][FNM:");
+	SERIAL_ECHO(longFilenameOLD);
+	SERIAL_ECHO("][TIM:");
+	if (starttime != 0)
+	{
+		SERIAL_ECHO(millis() / 1000 - starttime / 1000);
+	}
+	else
+	{
+		SERIAL_ECHO(0);
+	}
+	SERIAL_ECHO("][FWR:");
+	SERIAL_ECHO(FW_version);
+	SERIAL_ECHO("]");
+}
+
+
 void lcd_pick_babystep(){
     int enc_dif = 0;
     int cursor_pos = 1;
@@ -1732,7 +1944,10 @@ static void lcd_settings_menu()
     MENU_ITEM(submenu, MSG_CALIBRATE_BED, lcd_mesh_calibration);
     MENU_ITEM(gcode, MSG_CALIBRATE_BED_RESET, PSTR("M44"));
 	}
-  
+	if (farm_mode)
+	{
+		MENU_ITEM(submenu, PSTR("Farm number"), lcd_farm_no);
+	}
 	END_MENU();
 }
 /*
@@ -1920,6 +2135,123 @@ void lcd_mylang() {
 
 
 
+static void lcd_farm_no()
+{
+	int enc_dif = 0;
+	int _farmno = farm_no;
+	int _ret = 0;
+	lcd_implementation_clear();
+
+	lcd.setCursor(0, 0);
+	lcd.print("Farm no");
+
+	do
+	{
+
+		if (abs((enc_dif - encoderDiff)) > 2) {
+			if (enc_dif > encoderDiff) {
+				_farmno--;
+			}
+
+			if (enc_dif < encoderDiff) {
+				_farmno++;
+			}
+			enc_dif = 0;
+			encoderDiff = 0;
+		}
+
+		if (_farmno > 254) { _farmno = 1; }
+		if (_farmno < 1) { _farmno = 254; }
+
+
+		lcd.setCursor(0, 2);
+		lcd.print(_farmno);
+		lcd.print("  ");
+		delay(100);
+
+		if (lcd_clicked())
+		{
+			_ret = 1;
+			farm_no = _farmno;
+			EEPROM_save_B(EEPROM_FARM_MODE, &farm_no);
+			prusa_statistics(20);
+			lcd_return_to_status();
+		}
+
+		manage_heater();
+	} while (_ret == 0);
+
+}
+
+void lcd_confirm_print()
+{
+	int enc_dif = 0;
+	int cursor_pos = 1;
+	int _ret = 0;
+	int _t = 0;
+
+
+	lcd_implementation_clear();
+
+	lcd.setCursor(0, 0);
+	lcd.print("Print ok ?");
+
+	do
+	{
+
+		if (abs((enc_dif - encoderDiff)) > 2) {
+			if (enc_dif > encoderDiff) {
+				cursor_pos--;
+			}
+
+			if (enc_dif < encoderDiff) {
+				cursor_pos++;
+			}
+		}
+
+		if (cursor_pos > 2) { cursor_pos = 2; }
+		if (cursor_pos < 1) { cursor_pos = 1; }
+
+		lcd.setCursor(0, 2); lcd.print("          ");
+		lcd.setCursor(0, 3); lcd.print("          ");
+		lcd.setCursor(2, 2);
+		lcd_printPGM(MSG_YES);
+		lcd.setCursor(2, 3);
+		lcd_printPGM(MSG_NO);
+		lcd.setCursor(0, 1 + cursor_pos);
+		lcd.print(">");
+		delay(100);
+
+		_t = _t + 1;
+		if (_t>100)
+		{
+			prusa_statistics(99);
+			_t = 0;
+		}
+		if (lcd_clicked())
+		{
+			if (cursor_pos == 1)
+			{
+				_ret = 1;
+				prusa_statistics(20);
+				prusa_statistics(4);
+			}
+			if (cursor_pos == 2)
+			{
+				_ret = 2;
+				prusa_statistics(20);
+				prusa_statistics(5);
+			}
+		}
+
+		manage_heater();
+		manage_inactivity();
+
+	} while (_ret == 0);
+
+}
+
+
 
 static void lcd_main_menu()
 {

Firmware/ultralcd.h

@@ -26,6 +26,8 @@
   void lcd_loading_color();
   void lcd_force_language_selection();
   void lcd_sdcard_stop();
+  void prusa_statistics(int _message);
+  void lcd_confirm_print();
   
   bool lcd_detected(void);
 
@@ -76,6 +78,7 @@
   #else
   FORCE_INLINE void lcd_buttons_update() {}
   #endif
+  extern int lcd_commands_type;
 
   extern int plaPreheatHotendTemp;
   extern int plaPreheatHPBTemp;
@@ -85,6 +88,11 @@
   extern int absPreheatHPBTemp;
   extern int absPreheatFanSpeed;
   
+  extern bool farm_mode;
+  extern int farm_no;
+  extern int farm_timer;
+  extern int farm_status;
+
   extern bool cancel_heatup;
   
   #ifdef FILAMENT_LCD_DISPLAY

Firmware/ultralcd_implementation_hitachi_HD44780.h

@@ -711,7 +711,12 @@ static void lcd_implementation_status_screen()
 			lcd.print('%');
 		}
 	}
-    lcd.print("      ");
+	if (farm_mode)
+	{
+		lcd.print(" F");
+		lcd.print(farm_no);
+		lcd.print("  ");
+	}
 
     //Print time elapsed
     lcd.setCursor(LCD_WIDTH - 8 -2, 2);
@@ -885,15 +890,7 @@ static void lcd_implementation_status_screen()
         lcd.print(' ');
       }
     }
-
-	if (is_usb_printing==1 && custom_message==0)
-	{
-		lcd.setCursor(0, 3);
-		lcd.print("                    ");
-		lcd.setCursor(0, 3);
-		lcd_printPGM(MSG_USB_PRINTING);
-	}
-
+	
 }
 
 

Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h

@@ -244,8 +244,8 @@ BED SETTINGS
 PREHEAT SETTINGS
 *------------------------------------*/
 
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP 50
+#define PLA_PREHEAT_HOTEND_TEMP 215
+#define PLA_PREHEAT_HPB_TEMP 55
 #define PLA_PREHEAT_FAN_SPEED 0  
 
 #define ABS_PREHEAT_HOTEND_TEMP 255

Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h

@@ -244,8 +244,8 @@ BED SETTINGS
 PREHEAT SETTINGS
 *------------------------------------*/
 
-#define PLA_PREHEAT_HOTEND_TEMP 210
-#define PLA_PREHEAT_HPB_TEMP 50
+#define PLA_PREHEAT_HOTEND_TEMP 215
+#define PLA_PREHEAT_HPB_TEMP 55
 #define PLA_PREHEAT_FAN_SPEED 0  
 
 #define ABS_PREHEAT_HOTEND_TEMP 255