Ver Fonte

Merge pull request #2017 from NotaRobotexe/octoprint_fix

Octoprint fix
DRracer há 5 anos atrás
pai
commit
b0c41ec979

+ 14 - 4
Firmware/Marlin_main.cpp

@@ -3392,8 +3392,15 @@ void process_commands()
   if (fan_check_error){
 	if( fan_check_error == EFCE_DETECTED ){
 		fan_check_error = EFCE_REPORTED;
-		lcd_pause_print();
-	} // otherwise it has already been reported, so just ignore further processing
+      
+      if(is_usb_printing){
+        SERIAL_PROTOCOLLNRPGM(MSG_OCTOPRINT_PAUSE);
+      }
+      else{
+        lcd_pause_print();
+      }
+
+    } // otherwise it has already been reported, so just ignore further processing
     return;
   }
   #endif
@@ -6733,6 +6740,10 @@ Sigma_Exit:
 	}
 	break;
 
+  case 603: { //! M603 - Stop print
+		lcd_print_stop();
+	}
+
 #ifdef PINDA_THERMISTOR
 	case 860: // M860 - Wait for PINDA thermistor to reach target temperature.
 	{
@@ -9427,7 +9438,6 @@ void stop_and_save_print_to_ram(float z_move, float e_move)
 	if(!saved_extruder_relative_mode){
 		enquecommand(PSTR("M83"), true);
 	}
-	
 	//retract 45mm/s
 	// A single sprintf may not be faster, but is definitely 20B shorter
 	// than a sequence of commands building the string piece by piece
@@ -9511,7 +9521,6 @@ void restore_print_from_ram_and_continue(float e_move)
 		card.setIndex(saved_sdpos);
 		sdpos_atomic = saved_sdpos;
 		card.sdprinting = true;
-		printf_P(PSTR("ok\n")); //dummy response because of octoprint is waiting for this
 	}
 	else if (saved_printing_type == PRINTING_TYPE_USB) { //was usb printing
 		gcode_LastN = saved_sdpos; //saved_sdpos was reused for storing line number when usb printing
@@ -9521,6 +9530,7 @@ void restore_print_from_ram_and_continue(float e_move)
 	else {
 		//not sd printing nor usb printing
 	}
+	printf_P(PSTR("ok\n")); //dummy response because of octoprint is waiting for this
 	lcd_setstatuspgm(_T(WELCOME_MSG));
 	saved_printing = false;
 }

+ 1 - 0
Firmware/messages.c

@@ -129,3 +129,4 @@ const char MSG_ENDSTOP_OPEN[] PROGMEM_N1 = "open"; ////
 const char MSG_POWERUP[] PROGMEM_N1 = "PowerUp"; ////
 const char MSG_ERR_STOPPED[] PROGMEM_N1 = "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"; ////
 const char MSG_ENDSTOP_HIT[] PROGMEM_N1 = "TRIGGERED"; ////
+const char MSG_OCTOPRINT_PAUSE[] PROGMEM_N1 = "// action:pause"; ////

+ 1 - 0
Firmware/messages.h

@@ -130,6 +130,7 @@ extern const char MSG_ERR_STOPPED[];
 extern const char MSG_ENDSTOP_HIT[];
 extern const char MSG_EJECT_FILAMENT[];
 extern const char MSG_CUT_FILAMENT[];
+extern const char MSG_OCTOPRINT_PAUSE[];
 
 #if defined(__cplusplus)
 }

+ 6 - 4
Firmware/temperature.cpp

@@ -40,7 +40,7 @@
 #include <avr/wdt.h>
 #include "adc.h"
 #include "ConfigurationStore.h"
-
+#include "messages.h"
 #include "Timer.h"
 #include "Configuration_prusa.h"
 
@@ -525,6 +525,8 @@ void checkFanSpeed()
 		fan_speed_errors[1] = 0;
 		fanSpeedError(1); //print fan
 	}
+
+  SERIAL_PROTOCOLLNRPGM(MSG_OK); //for octoprint
 }
 
 //! Prints serialMsg to serial port, displays lcdMsg onto the LCD and beeps.
@@ -542,18 +544,17 @@ static void fanSpeedErrorBeep(const char *serialMsg, const char *lcdMsg){
 void fanSpeedError(unsigned char _fan) {
 	if (get_message_level() != 0 && isPrintPaused) return; 
 	//to ensure that target temp. is not set to zero in case taht we are resuming print 
-	if (card.sdprinting) {
+	if (card.sdprinting || is_usb_printing) {
 		if (heating_status != 0) {
 			lcd_print_stop();
 		}
 		else {
 			fan_check_error = EFCE_DETECTED;
-
 		}
 	}
 	else {
+			SERIAL_PROTOCOLLNRPGM(MSG_OCTOPRINT_PAUSE); //for octoprint
 			setTargetHotend0(0);
-			SERIAL_ECHOLNPGM("// action:pause"); //for octoprint
       heating_status = 0;
       fan_check_error = EFCE_REPORTED;
 	}
@@ -565,6 +566,7 @@ void fanSpeedError(unsigned char _fan) {
 		fanSpeedErrorBeep(PSTR("Print fan speed is lower than expected"), PSTR("Err: PRINT FAN ERROR") );
 		break;
 	}
+  SERIAL_PROTOCOLLNRPGM(MSG_OK);
 }
 #endif //(defined(TACH_0) && TACH_0 >-1) || (defined(TACH_1) && TACH_1 > -1)
 

+ 1 - 1
Firmware/ultralcd.cpp

@@ -1658,6 +1658,7 @@ void lcd_pause_print()
     {
         lcd_commands_type = LcdCommands::LongPause;
     }
+	SERIAL_PROTOCOLLNRPGM(MSG_OCTOPRINT_PAUSE); //pause for octoprint
 }
 
 
@@ -6970,7 +6971,6 @@ void lcd_print_stop()
      if(!card.sdprinting)
           {
           SERIAL_ECHOLNPGM("// action:cancel");   // for Octoprint
-          return;
           }
 	saved_printing = false;
 	cancel_heatup = true;