czech messages added, temperature calibration is off in fresh eeprom, pinda preheat phase is not used unless calibration was run, pause print works with gcode absolute and relative extruder mode, move z higher after selftest

Firmware/Marlin_main.cpp

@@ -1162,11 +1162,12 @@ void setup()
     if (lang_selected >= LANG_NUM){
       lcd_mylang();
     }
-	temp_cal_active = eeprom_read_byte((uint8_t*)EEPROM_TEMP_CAL_ACTIVE);
-	if (temp_cal_active == 0xFF) {
+	
+	if (eeprom_read_byte((uint8_t*)EEPROM_TEMP_CAL_ACTIVE) == 255) {
 		eeprom_write_byte((uint8_t*)EEPROM_TEMP_CAL_ACTIVE, 0);
-		temp_cal_active = 0;
-	}
+		temp_cal_active = false;
+	} else temp_cal_active = eeprom_read_byte((uint8_t*)EEPROM_TEMP_CAL_ACTIVE);
+
 	check_babystep(); //checking if Z babystep is in allowed range
 	
   if (calibration_status() == CALIBRATION_STATUS_ASSEMBLED ||
@@ -2948,7 +2949,7 @@ void process_commands()
 			break;
 		} 
 		
-		if (run == false && card.sdprinting == true && temp_cal_active == true) {
+		if (run == false && card.sdprinting == true && temp_cal_active == true && calibration_status() < CALIBRATION_STATUS_PINDA) {
 			temp_compensation_start();
 			run = true;
 			repeatcommand_front(); // repeat G80 with all its parameters
@@ -3095,7 +3096,7 @@ void process_commands()
 		}
 		clean_up_after_endstop_move();
 		SERIAL_ECHOLNPGM("clean up finished ");
-		if(temp_cal_active == true) temp_compensation_apply(); //apply PINDA temperature compensation
+		if(temp_cal_active == true && calibration_status() < CALIBRATION_STATUS_PINDA) temp_compensation_apply(); //apply PINDA temperature compensation
 		babystep_apply(); // Apply Z height correction aka baby stepping before mesh bed leveing gets activated.
 		SERIAL_ECHOLNPGM("babystep applied");
 		bool eeprom_bed_correction_valid = eeprom_read_byte((unsigned char*)EEPROM_BED_CORRECTION_VALID) == 1;

Firmware/language_all.cpp

@@ -494,13 +494,25 @@ const char * const MSG_CALIBRATE_E_LANG_TABLE[LANG_NUM] PROGMEM = {
 	MSG_CALIBRATE_E_DE
 };
 
-const char MSG_CALIBRATE_PINDA_EN[] PROGMEM = "Temp. calibration";
-const char * const MSG_CALIBRATE_PINDA_LANG_TABLE[1] PROGMEM = {
+const char MSG_CALIBRATE_PINDA_EN[] PROGMEM = "Calibrate";
+const char MSG_CALIBRATE_PINDA_CZ[] PROGMEM = "Zkalibrovat";
+const char * const MSG_CALIBRATE_PINDA_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_CALIBRATE_PINDA_EN,
+	MSG_CALIBRATE_PINDA_CZ,
+	MSG_CALIBRATE_PINDA_EN,
+	MSG_CALIBRATE_PINDA_EN,
+	MSG_CALIBRATE_PINDA_EN,
 	MSG_CALIBRATE_PINDA_EN
 };
 
 const char MSG_CALIBRATION_PINDA_MENU_EN[] PROGMEM = "Temp. calibration";
-const char * const MSG_CALIBRATION_PINDA_MENU_LANG_TABLE[1] PROGMEM = {
+const char MSG_CALIBRATION_PINDA_MENU_CZ[] PROGMEM = "Teplotni kalibrace";
+const char * const MSG_CALIBRATION_PINDA_MENU_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_CALIBRATION_PINDA_MENU_EN,
+	MSG_CALIBRATION_PINDA_MENU_CZ,
+	MSG_CALIBRATION_PINDA_MENU_EN,
+	MSG_CALIBRATION_PINDA_MENU_EN,
+	MSG_CALIBRATION_PINDA_MENU_EN,
 	MSG_CALIBRATION_PINDA_MENU_EN
 };
 
@@ -702,11 +714,6 @@ const char * const MSG_DWELL_LANG_TABLE[LANG_NUM] PROGMEM = {
 	MSG_DWELL_DE
 };
 
-const char MSG_EEPROM_SAVING_EN[] PROGMEM = "Saving";
-const char * const MSG_EEPROM_SAVING_LANG_TABLE[1] PROGMEM = {
-	MSG_EEPROM_SAVING_EN
-};
-
 const char MSG_ENDSTOPS_HIT_EN[] PROGMEM = "endstops hit: ";
 const char * const MSG_ENDSTOPS_HIT_LANG_TABLE[1] PROGMEM = {
 	MSG_ENDSTOPS_HIT_EN
@@ -1017,7 +1024,13 @@ const char * const MSG_FIND_BED_OFFSET_AND_SKEW_LINE2_LANG_TABLE[LANG_NUM] PROGM
 };
 
 const char MSG_FINISHING_MOVEMENTS_EN[] PROGMEM = "Finishing movements";
-const char * const MSG_FINISHING_MOVEMENTS_LANG_TABLE[1] PROGMEM = {
+const char MSG_FINISHING_MOVEMENTS_CZ[] PROGMEM = "Dokoncovani pohybu";
+const char * const MSG_FINISHING_MOVEMENTS_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_FINISHING_MOVEMENTS_EN,
+	MSG_FINISHING_MOVEMENTS_CZ,
+	MSG_FINISHING_MOVEMENTS_EN,
+	MSG_FINISHING_MOVEMENTS_EN,
+	MSG_FINISHING_MOVEMENTS_EN,
 	MSG_FINISHING_MOVEMENTS_EN
 };
 
@@ -1757,27 +1770,57 @@ const char * const MSG_PICK_Z_LANG_TABLE[LANG_NUM] PROGMEM = {
 };
 
 const char MSG_PID_EXTRUDER_EN[] PROGMEM = "PID calibration";
-const char * const MSG_PID_EXTRUDER_LANG_TABLE[1] PROGMEM = {
+const char MSG_PID_EXTRUDER_CZ[] PROGMEM = "PID kalibrace";
+const char * const MSG_PID_EXTRUDER_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_PID_EXTRUDER_EN,
+	MSG_PID_EXTRUDER_CZ,
+	MSG_PID_EXTRUDER_EN,
+	MSG_PID_EXTRUDER_EN,
+	MSG_PID_EXTRUDER_EN,
 	MSG_PID_EXTRUDER_EN
 };
 
 const char MSG_PID_FINISHED_EN[] PROGMEM = "PID cal. finished";
-const char * const MSG_PID_FINISHED_LANG_TABLE[1] PROGMEM = {
+const char MSG_PID_FINISHED_CZ[] PROGMEM = "PID kal. ukoncena";
+const char * const MSG_PID_FINISHED_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_PID_FINISHED_EN,
+	MSG_PID_FINISHED_CZ,
+	MSG_PID_FINISHED_EN,
+	MSG_PID_FINISHED_EN,
+	MSG_PID_FINISHED_EN,
 	MSG_PID_FINISHED_EN
 };
 
 const char MSG_PID_RUNNING_EN[] PROGMEM = "PID cal.           ";
-const char * const MSG_PID_RUNNING_LANG_TABLE[1] PROGMEM = {
+const char MSG_PID_RUNNING_CZ[] PROGMEM = "PID kal.           ";
+const char * const MSG_PID_RUNNING_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_PID_RUNNING_EN,
+	MSG_PID_RUNNING_CZ,
+	MSG_PID_RUNNING_EN,
+	MSG_PID_RUNNING_EN,
+	MSG_PID_RUNNING_EN,
 	MSG_PID_RUNNING_EN
 };
 
 const char MSG_PINDA_NOT_CALIBRATED_EN[] PROGMEM = "Temperature calibration has not been run yet";
-const char * const MSG_PINDA_NOT_CALIBRATED_LANG_TABLE[1] PROGMEM = {
+const char MSG_PINDA_NOT_CALIBRATED_CZ[] PROGMEM = "Tiskarna nebyla teplotne zkalibrovana";
+const char * const MSG_PINDA_NOT_CALIBRATED_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_PINDA_NOT_CALIBRATED_EN,
+	MSG_PINDA_NOT_CALIBRATED_CZ,
+	MSG_PINDA_NOT_CALIBRATED_EN,
+	MSG_PINDA_NOT_CALIBRATED_EN,
+	MSG_PINDA_NOT_CALIBRATED_EN,
 	MSG_PINDA_NOT_CALIBRATED_EN
 };
 
 const char MSG_PINDA_PREHEAT_EN[] PROGMEM = "Preheating";
-const char * const MSG_PINDA_PREHEAT_LANG_TABLE[1] PROGMEM = {
+const char MSG_PINDA_PREHEAT_CZ[] PROGMEM = "Predehrivani";
+const char * const MSG_PINDA_PREHEAT_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_PINDA_PREHEAT_EN,
+	MSG_PINDA_PREHEAT_CZ,
+	MSG_PINDA_PREHEAT_EN,
+	MSG_PINDA_PREHEAT_EN,
+	MSG_PINDA_PREHEAT_EN,
 	MSG_PINDA_PREHEAT_EN
 };
 
@@ -1877,7 +1920,13 @@ const char * const MSG_PRINT_ABORTED_LANG_TABLE[LANG_NUM] PROGMEM = {
 };
 
 const char MSG_PRINT_PAUSED_EN[] PROGMEM = "Print paused";
-const char * const MSG_PRINT_PAUSED_LANG_TABLE[1] PROGMEM = {
+const char MSG_PRINT_PAUSED_CZ[] PROGMEM = "Tisk pozastaven";
+const char * const MSG_PRINT_PAUSED_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_PRINT_PAUSED_EN,
+	MSG_PRINT_PAUSED_CZ,
+	MSG_PRINT_PAUSED_EN,
+	MSG_PRINT_PAUSED_EN,
+	MSG_PRINT_PAUSED_EN,
 	MSG_PRINT_PAUSED_EN
 };
 
@@ -1988,7 +2037,13 @@ const char * const MSG_RESUMING_LANG_TABLE[LANG_NUM] PROGMEM = {
 };
 
 const char MSG_RESUMING_PRINT_EN[] PROGMEM = "Resuming print";
-const char * const MSG_RESUMING_PRINT_LANG_TABLE[1] PROGMEM = {
+const char MSG_RESUMING_PRINT_CZ[] PROGMEM = "Obnovovani tisku";
+const char * const MSG_RESUMING_PRINT_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_RESUMING_PRINT_EN,
+	MSG_RESUMING_PRINT_CZ,
+	MSG_RESUMING_PRINT_EN,
+	MSG_RESUMING_PRINT_EN,
+	MSG_RESUMING_PRINT_EN,
 	MSG_RESUMING_PRINT_EN
 };
 
@@ -2491,8 +2546,14 @@ const char * const MSG_SET_ORIGIN_LANG_TABLE[1] PROGMEM = {
 	MSG_SET_ORIGIN_EN
 };
 
-const char MSG_SET_TEMPERATURE_EN[] PROGMEM = "Set temperature";
-const char * const MSG_SET_TEMPERATURE_LANG_TABLE[1] PROGMEM = {
+const char MSG_SET_TEMPERATURE_EN[] PROGMEM = "Set temperature:";
+const char MSG_SET_TEMPERATURE_CZ[] PROGMEM = "Nastavte teplotu:";
+const char * const MSG_SET_TEMPERATURE_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_SET_TEMPERATURE_EN,
+	MSG_SET_TEMPERATURE_CZ,
+	MSG_SET_TEMPERATURE_EN,
+	MSG_SET_TEMPERATURE_EN,
+	MSG_SET_TEMPERATURE_EN,
 	MSG_SET_TEMPERATURE_EN
 };
 
@@ -2748,23 +2809,47 @@ const char * const MSG_TEMPERATURE_LANG_TABLE[LANG_NUM] PROGMEM = {
 	MSG_TEMPERATURE_DE
 };
 
-const char MSG_TEMP_CALIBRATION_EN[] PROGMEM = "Temp. calibration   ";
-const char * const MSG_TEMP_CALIBRATION_LANG_TABLE[1] PROGMEM = {
+const char MSG_TEMP_CALIBRATION_EN[] PROGMEM = "Temp. cal.          ";
+const char MSG_TEMP_CALIBRATION_CZ[] PROGMEM = "Tepl. kal.          ";
+const char * const MSG_TEMP_CALIBRATION_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_TEMP_CALIBRATION_EN,
+	MSG_TEMP_CALIBRATION_CZ,
+	MSG_TEMP_CALIBRATION_EN,
+	MSG_TEMP_CALIBRATION_EN,
+	MSG_TEMP_CALIBRATION_EN,
 	MSG_TEMP_CALIBRATION_EN
 };
 
 const char MSG_TEMP_CALIBRATION_DONE_EN[] PROGMEM = "Temperature calibration is finished. Click to continue.";
-const char * const MSG_TEMP_CALIBRATION_DONE_LANG_TABLE[1] PROGMEM = {
+const char MSG_TEMP_CALIBRATION_DONE_CZ[] PROGMEM = "Teplotni kalibrace dokoncena. Pokracujte stiskem tlacitka.";
+const char * const MSG_TEMP_CALIBRATION_DONE_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_TEMP_CALIBRATION_DONE_EN,
+	MSG_TEMP_CALIBRATION_DONE_CZ,
+	MSG_TEMP_CALIBRATION_DONE_EN,
+	MSG_TEMP_CALIBRATION_DONE_EN,
+	MSG_TEMP_CALIBRATION_DONE_EN,
 	MSG_TEMP_CALIBRATION_DONE_EN
 };
 
 const char MSG_TEMP_CALIBRATION_OFF_EN[] PROGMEM = "Temp. cal. [OFF]";
-const char * const MSG_TEMP_CALIBRATION_OFF_LANG_TABLE[1] PROGMEM = {
+const char MSG_TEMP_CALIBRATION_OFF_CZ[] PROGMEM = "Tepl. kal. [OFF]";
+const char * const MSG_TEMP_CALIBRATION_OFF_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_TEMP_CALIBRATION_OFF_EN,
+	MSG_TEMP_CALIBRATION_OFF_CZ,
+	MSG_TEMP_CALIBRATION_OFF_EN,
+	MSG_TEMP_CALIBRATION_OFF_EN,
+	MSG_TEMP_CALIBRATION_OFF_EN,
 	MSG_TEMP_CALIBRATION_OFF_EN
 };
 
 const char MSG_TEMP_CALIBRATION_ON_EN[] PROGMEM = "Temp. cal. [ON]";
-const char * const MSG_TEMP_CALIBRATION_ON_LANG_TABLE[1] PROGMEM = {
+const char MSG_TEMP_CALIBRATION_ON_CZ[] PROGMEM = "Tepl. kal. [ON]";
+const char * const MSG_TEMP_CALIBRATION_ON_LANG_TABLE[LANG_NUM] PROGMEM = {
+	MSG_TEMP_CALIBRATION_ON_EN,
+	MSG_TEMP_CALIBRATION_ON_CZ,
+	MSG_TEMP_CALIBRATION_ON_EN,
+	MSG_TEMP_CALIBRATION_ON_EN,
+	MSG_TEMP_CALIBRATION_ON_EN,
 	MSG_TEMP_CALIBRATION_ON_EN
 };
 

Firmware/language_all.h

@@ -107,10 +107,10 @@ extern const char* const MSG_CALIBRATE_BED_RESET_LANG_TABLE[LANG_NUM];
 #define MSG_CALIBRATE_BED_RESET LANG_TABLE_SELECT(MSG_CALIBRATE_BED_RESET_LANG_TABLE)
 extern const char* const MSG_CALIBRATE_E_LANG_TABLE[LANG_NUM];
 #define MSG_CALIBRATE_E LANG_TABLE_SELECT(MSG_CALIBRATE_E_LANG_TABLE)
-extern const char* const MSG_CALIBRATE_PINDA_LANG_TABLE[1];
-#define MSG_CALIBRATE_PINDA LANG_TABLE_SELECT_EXPLICIT(MSG_CALIBRATE_PINDA_LANG_TABLE, 0)
-extern const char* const MSG_CALIBRATION_PINDA_MENU_LANG_TABLE[1];
-#define MSG_CALIBRATION_PINDA_MENU LANG_TABLE_SELECT_EXPLICIT(MSG_CALIBRATION_PINDA_MENU_LANG_TABLE, 0)
+extern const char* const MSG_CALIBRATE_PINDA_LANG_TABLE[LANG_NUM];
+#define MSG_CALIBRATE_PINDA LANG_TABLE_SELECT(MSG_CALIBRATE_PINDA_LANG_TABLE)
+extern const char* const MSG_CALIBRATION_PINDA_MENU_LANG_TABLE[LANG_NUM];
+#define MSG_CALIBRATION_PINDA_MENU LANG_TABLE_SELECT(MSG_CALIBRATION_PINDA_MENU_LANG_TABLE)
 extern const char* const MSG_CARD_MENU_LANG_TABLE[LANG_NUM];
 #define MSG_CARD_MENU LANG_TABLE_SELECT(MSG_CARD_MENU_LANG_TABLE)
 extern const char* const MSG_CHANGE_EXTR_LANG_TABLE[LANG_NUM];
@@ -143,8 +143,6 @@ extern const char* const MSG_DISABLE_STEPPERS_LANG_TABLE[LANG_NUM];
 #define MSG_DISABLE_STEPPERS LANG_TABLE_SELECT(MSG_DISABLE_STEPPERS_LANG_TABLE)
 extern const char* const MSG_DWELL_LANG_TABLE[LANG_NUM];
 #define MSG_DWELL LANG_TABLE_SELECT(MSG_DWELL_LANG_TABLE)
-extern const char* const MSG_EEPROM_SAVING_LANG_TABLE[1];
-#define MSG_EEPROM_SAVING LANG_TABLE_SELECT_EXPLICIT(MSG_EEPROM_SAVING_LANG_TABLE, 0)
 extern const char* const MSG_ENDSTOPS_HIT_LANG_TABLE[1];
 #define MSG_ENDSTOPS_HIT LANG_TABLE_SELECT_EXPLICIT(MSG_ENDSTOPS_HIT_LANG_TABLE, 0)
 extern const char* const MSG_ENDSTOP_HIT_LANG_TABLE[1];
@@ -213,8 +211,8 @@ extern const char* const MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_LANG_TABLE[LANG_NUM]
 #define MSG_FIND_BED_OFFSET_AND_SKEW_LINE1 LANG_TABLE_SELECT(MSG_FIND_BED_OFFSET_AND_SKEW_LINE1_LANG_TABLE)
 extern const char* const MSG_FIND_BED_OFFSET_AND_SKEW_LINE2_LANG_TABLE[LANG_NUM];
 #define MSG_FIND_BED_OFFSET_AND_SKEW_LINE2 LANG_TABLE_SELECT(MSG_FIND_BED_OFFSET_AND_SKEW_LINE2_LANG_TABLE)
-extern const char* const MSG_FINISHING_MOVEMENTS_LANG_TABLE[1];
-#define MSG_FINISHING_MOVEMENTS LANG_TABLE_SELECT_EXPLICIT(MSG_FINISHING_MOVEMENTS_LANG_TABLE, 0)
+extern const char* const MSG_FINISHING_MOVEMENTS_LANG_TABLE[LANG_NUM];
+#define MSG_FINISHING_MOVEMENTS LANG_TABLE_SELECT(MSG_FINISHING_MOVEMENTS_LANG_TABLE)
 extern const char* const MSG_FLOW_LANG_TABLE[LANG_NUM];
 #define MSG_FLOW LANG_TABLE_SELECT(MSG_FLOW_LANG_TABLE)
 extern const char* const MSG_FLOW0_LANG_TABLE[1];
@@ -353,16 +351,16 @@ extern const char* const MSG_PAUSE_PRINT_LANG_TABLE[LANG_NUM];
 #define MSG_PAUSE_PRINT LANG_TABLE_SELECT(MSG_PAUSE_PRINT_LANG_TABLE)
 extern const char* const MSG_PICK_Z_LANG_TABLE[LANG_NUM];
 #define MSG_PICK_Z LANG_TABLE_SELECT(MSG_PICK_Z_LANG_TABLE)
-extern const char* const MSG_PID_EXTRUDER_LANG_TABLE[1];
-#define MSG_PID_EXTRUDER LANG_TABLE_SELECT_EXPLICIT(MSG_PID_EXTRUDER_LANG_TABLE, 0)
-extern const char* const MSG_PID_FINISHED_LANG_TABLE[1];
-#define MSG_PID_FINISHED LANG_TABLE_SELECT_EXPLICIT(MSG_PID_FINISHED_LANG_TABLE, 0)
-extern const char* const MSG_PID_RUNNING_LANG_TABLE[1];
-#define MSG_PID_RUNNING LANG_TABLE_SELECT_EXPLICIT(MSG_PID_RUNNING_LANG_TABLE, 0)
-extern const char* const MSG_PINDA_NOT_CALIBRATED_LANG_TABLE[1];
-#define MSG_PINDA_NOT_CALIBRATED LANG_TABLE_SELECT_EXPLICIT(MSG_PINDA_NOT_CALIBRATED_LANG_TABLE, 0)
-extern const char* const MSG_PINDA_PREHEAT_LANG_TABLE[1];
-#define MSG_PINDA_PREHEAT LANG_TABLE_SELECT_EXPLICIT(MSG_PINDA_PREHEAT_LANG_TABLE, 0)
+extern const char* const MSG_PID_EXTRUDER_LANG_TABLE[LANG_NUM];
+#define MSG_PID_EXTRUDER LANG_TABLE_SELECT(MSG_PID_EXTRUDER_LANG_TABLE)
+extern const char* const MSG_PID_FINISHED_LANG_TABLE[LANG_NUM];
+#define MSG_PID_FINISHED LANG_TABLE_SELECT(MSG_PID_FINISHED_LANG_TABLE)
+extern const char* const MSG_PID_RUNNING_LANG_TABLE[LANG_NUM];
+#define MSG_PID_RUNNING LANG_TABLE_SELECT(MSG_PID_RUNNING_LANG_TABLE)
+extern const char* const MSG_PINDA_NOT_CALIBRATED_LANG_TABLE[LANG_NUM];
+#define MSG_PINDA_NOT_CALIBRATED LANG_TABLE_SELECT(MSG_PINDA_NOT_CALIBRATED_LANG_TABLE)
+extern const char* const MSG_PINDA_PREHEAT_LANG_TABLE[LANG_NUM];
+#define MSG_PINDA_PREHEAT LANG_TABLE_SELECT(MSG_PINDA_PREHEAT_LANG_TABLE)
 extern const char* const MSG_PLANNER_BUFFER_BYTES_LANG_TABLE[1];
 #define MSG_PLANNER_BUFFER_BYTES LANG_TABLE_SELECT_EXPLICIT(MSG_PLANNER_BUFFER_BYTES_LANG_TABLE, 0)
 extern const char* const MSG_PLEASE_WAIT_LANG_TABLE[LANG_NUM];
@@ -381,8 +379,8 @@ extern const char* const MSG_PRINTER_DISCONNECTED_LANG_TABLE[1];
 #define MSG_PRINTER_DISCONNECTED LANG_TABLE_SELECT_EXPLICIT(MSG_PRINTER_DISCONNECTED_LANG_TABLE, 0)
 extern const char* const MSG_PRINT_ABORTED_LANG_TABLE[LANG_NUM];
 #define MSG_PRINT_ABORTED LANG_TABLE_SELECT(MSG_PRINT_ABORTED_LANG_TABLE)
-extern const char* const MSG_PRINT_PAUSED_LANG_TABLE[1];
-#define MSG_PRINT_PAUSED LANG_TABLE_SELECT_EXPLICIT(MSG_PRINT_PAUSED_LANG_TABLE, 0)
+extern const char* const MSG_PRINT_PAUSED_LANG_TABLE[LANG_NUM];
+#define MSG_PRINT_PAUSED LANG_TABLE_SELECT(MSG_PRINT_PAUSED_LANG_TABLE)
 extern const char* const MSG_PRUSA3D_LANG_TABLE[LANG_NUM];
 #define MSG_PRUSA3D LANG_TABLE_SELECT(MSG_PRUSA3D_LANG_TABLE)
 extern const char* const MSG_PRUSA3D_FORUM_LANG_TABLE[LANG_NUM];
@@ -405,8 +403,8 @@ extern const char* const MSG_RESUME_PRINT_LANG_TABLE[LANG_NUM];
 #define MSG_RESUME_PRINT LANG_TABLE_SELECT(MSG_RESUME_PRINT_LANG_TABLE)
 extern const char* const MSG_RESUMING_LANG_TABLE[LANG_NUM];
 #define MSG_RESUMING LANG_TABLE_SELECT(MSG_RESUMING_LANG_TABLE)
-extern const char* const MSG_RESUMING_PRINT_LANG_TABLE[1];
-#define MSG_RESUMING_PRINT LANG_TABLE_SELECT_EXPLICIT(MSG_RESUMING_PRINT_LANG_TABLE, 0)
+extern const char* const MSG_RESUMING_PRINT_LANG_TABLE[LANG_NUM];
+#define MSG_RESUMING_PRINT LANG_TABLE_SELECT(MSG_RESUMING_PRINT_LANG_TABLE)
 extern const char* const MSG_SD_CANT_ENTER_SUBDIR_LANG_TABLE[1];
 #define MSG_SD_CANT_ENTER_SUBDIR LANG_TABLE_SELECT_EXPLICIT(MSG_SD_CANT_ENTER_SUBDIR_LANG_TABLE, 0)
 extern const char* const MSG_SD_CANT_OPEN_SUBDIR_LANG_TABLE[1];
@@ -501,8 +499,8 @@ extern const char* const MSG_SET_HOME_OFFSETS_LANG_TABLE[1];
 #define MSG_SET_HOME_OFFSETS LANG_TABLE_SELECT_EXPLICIT(MSG_SET_HOME_OFFSETS_LANG_TABLE, 0)
 extern const char* const MSG_SET_ORIGIN_LANG_TABLE[1];
 #define MSG_SET_ORIGIN LANG_TABLE_SELECT_EXPLICIT(MSG_SET_ORIGIN_LANG_TABLE, 0)
-extern const char* const MSG_SET_TEMPERATURE_LANG_TABLE[1];
-#define MSG_SET_TEMPERATURE LANG_TABLE_SELECT_EXPLICIT(MSG_SET_TEMPERATURE_LANG_TABLE, 0)
+extern const char* const MSG_SET_TEMPERATURE_LANG_TABLE[LANG_NUM];
+#define MSG_SET_TEMPERATURE LANG_TABLE_SELECT(MSG_SET_TEMPERATURE_LANG_TABLE)
 extern const char* const MSG_SHOW_END_STOPS_LANG_TABLE[LANG_NUM];
 #define MSG_SHOW_END_STOPS LANG_TABLE_SELECT(MSG_SHOW_END_STOPS_LANG_TABLE)
 extern const char* const MSG_SILENT_MODE_OFF_LANG_TABLE[LANG_NUM];
@@ -543,14 +541,14 @@ extern const char* const MSG_TAKE_EFFECT_LANG_TABLE[LANG_NUM];
 #define MSG_TAKE_EFFECT LANG_TABLE_SELECT(MSG_TAKE_EFFECT_LANG_TABLE)
 extern const char* const MSG_TEMPERATURE_LANG_TABLE[LANG_NUM];
 #define MSG_TEMPERATURE LANG_TABLE_SELECT(MSG_TEMPERATURE_LANG_TABLE)
-extern const char* const MSG_TEMP_CALIBRATION_LANG_TABLE[1];
-#define MSG_TEMP_CALIBRATION LANG_TABLE_SELECT_EXPLICIT(MSG_TEMP_CALIBRATION_LANG_TABLE, 0)
-extern const char* const MSG_TEMP_CALIBRATION_DONE_LANG_TABLE[1];
-#define MSG_TEMP_CALIBRATION_DONE LANG_TABLE_SELECT_EXPLICIT(MSG_TEMP_CALIBRATION_DONE_LANG_TABLE, 0)
-extern const char* const MSG_TEMP_CALIBRATION_OFF_LANG_TABLE[1];
-#define MSG_TEMP_CALIBRATION_OFF LANG_TABLE_SELECT_EXPLICIT(MSG_TEMP_CALIBRATION_OFF_LANG_TABLE, 0)
-extern const char* const MSG_TEMP_CALIBRATION_ON_LANG_TABLE[1];
-#define MSG_TEMP_CALIBRATION_ON LANG_TABLE_SELECT_EXPLICIT(MSG_TEMP_CALIBRATION_ON_LANG_TABLE, 0)
+extern const char* const MSG_TEMP_CALIBRATION_LANG_TABLE[LANG_NUM];
+#define MSG_TEMP_CALIBRATION LANG_TABLE_SELECT(MSG_TEMP_CALIBRATION_LANG_TABLE)
+extern const char* const MSG_TEMP_CALIBRATION_DONE_LANG_TABLE[LANG_NUM];
+#define MSG_TEMP_CALIBRATION_DONE LANG_TABLE_SELECT(MSG_TEMP_CALIBRATION_DONE_LANG_TABLE)
+extern const char* const MSG_TEMP_CALIBRATION_OFF_LANG_TABLE[LANG_NUM];
+#define MSG_TEMP_CALIBRATION_OFF LANG_TABLE_SELECT(MSG_TEMP_CALIBRATION_OFF_LANG_TABLE)
+extern const char* const MSG_TEMP_CALIBRATION_ON_LANG_TABLE[LANG_NUM];
+#define MSG_TEMP_CALIBRATION_ON LANG_TABLE_SELECT(MSG_TEMP_CALIBRATION_ON_LANG_TABLE)
 extern const char* const MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF_LANG_TABLE[LANG_NUM];
 #define MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF LANG_TABLE_SELECT(MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF_LANG_TABLE)
 extern const char* const MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON_LANG_TABLE[LANG_NUM];

Firmware/language_cz.h

@@ -264,4 +264,21 @@
 #define MSG_FILAMENT_CLEAN								"Je barva cista?" 
 #define MSG_UNLOADING_FILAMENT							"Vysouvam filament"
 
-#define MSG_PAPER										"Umistete list papiru na podlozku a udrzujte jej pod tryskou behem mereni prvnich 4 bodu. Pokud tryska zachyti papir, vypnete tiskarnu."
+#define MSG_PAPER										"Umistete list papiru na podlozku a udrzujte jej pod tryskou behem mereni prvnich 4 bodu. Pokud tryska zachyti papir, vypnete tiskarnu."
+
+#define MSG_FINISHING_MOVEMENTS							"Dokoncovani pohybu"
+#define MSG_PRINT_PAUSED								"Tisk pozastaven"
+#define MSG_RESUMING_PRINT								"Obnovovani tisku"
+#define MSG_PID_EXTRUDER								"PID kalibrace"
+#define MSG_SET_TEMPERATURE								"Nastavte teplotu:"
+#define MSG_PID_FINISHED								"PID kal. ukoncena"
+#define MSG_PID_RUNNING									"PID kal.           "
+
+#define MSG_CALIBRATE_PINDA								"Zkalibrovat"
+#define MSG_CALIBRATION_PINDA_MENU						"Teplotni kalibrace"
+#define MSG_PINDA_NOT_CALIBRATED						"Tiskarna nebyla teplotne zkalibrovana"
+#define MSG_PINDA_PREHEAT								"Predehrivani"
+#define MSG_TEMP_CALIBRATION							"Tepl. kal.          "
+#define MSG_TEMP_CALIBRATION_DONE						"Teplotni kalibrace dokoncena. Pokracujte stiskem tlacitka."
+#define MSG_TEMP_CALIBRATION_ON							"Tepl. kal. [ON]"
+#define MSG_TEMP_CALIBRATION_OFF						"Tepl. kal. [OFF]"

Firmware/language_en.h

@@ -267,20 +267,20 @@
 #define MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF					"SD card [normal]"
 #define MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON					"SD card [FlshAir]"
 #define MSG_PRINTER_DISCONNECTED								"Printer disconnected"
-#define MSG_FINISHING_MOVEMENTS									"Finishing movements"
-#define MSG_PRINT_PAUSED										"Print paused"
-#define MSG_RESUMING_PRINT										"Resuming print"
-#define MSG_PID_EXTRUDER										"PID calibration"
-#define MSG_SET_TEMPERATURE										"Set temperature"
-#define MSG_PID_FINISHED										"PID cal. finished"
-#define MSG_PID_RUNNING											"PID cal.           "
-#define MSG_EEPROM_SAVING										"Saving"
+#define(length=20, lines=1) MSG_FINISHING_MOVEMENTS				"Finishing movements"
+#define(length=20, lines=1) MSG_PRINT_PAUSED					"Print paused"
+#define(length=20, lines=1) MSG_RESUMING_PRINT					"Resuming print"
+#define(length=17, lines=1) MSG_PID_EXTRUDER					"PID calibration"
+#define(length=19, lines=1) MSG_SET_TEMPERATURE					"Set temperature:"
+#define(length=20, lines=1) MSG_PID_FINISHED					"PID cal. finished"
+#define(length=20, lines=1) MSG_PID_RUNNING						"PID cal.           "
+
+#define(length=17, lines=1) MSG_CALIBRATE_PINDA					"Calibrate"
+#define(length=17, lines=1) MSG_CALIBRATION_PINDA_MENU			"Temp. calibration"
+#define(length=20, lines=4) MSG_PINDA_NOT_CALIBRATED			"Temperature calibration has not been run yet"
+#define(length=20, lines=1) MSG_PINDA_PREHEAT					"Preheating"
+#define(length=20, lines=1) MSG_TEMP_CALIBRATION				"Temp. cal.          "
+#define(length=20, lines=4) MSG_TEMP_CALIBRATION_DONE			"Temperature calibration is finished. Click to continue."
+#define(length=20, lines=1) MSG_TEMP_CALIBRATION_ON				"Temp. cal. [ON]"
+#define(length=20, lines=1) MSG_TEMP_CALIBRATION_OFF			"Temp. cal. [OFF]"
 
-#define MSG_CALIBRATE_PINDA										"Temp. calibration"
-#define MSG_CALIBRATION_PINDA_MENU								"Temp. calibration"
-#define MSG_PINDA_NOT_CALIBRATED								"Temperature calibration has not been run yet"
-#define MSG_PINDA_PREHEAT										"Preheating"
-#define MSG_TEMP_CALIBRATION									"Temp. calibration   "
-#define MSG_TEMP_CALIBRATION_DONE								"Temperature calibration is finished. Click to continue."
-#define MSG_TEMP_CALIBRATION_ON									"Temp. cal. [ON]"
-#define MSG_TEMP_CALIBRATION_OFF								"Temp. cal. [OFF]"

Firmware/ultralcd.cpp

@@ -556,7 +556,8 @@ void lcd_commands()
 			strcpy(cmd1, "G1 Z");
 			strcat(cmd1, ftostr32(pause_lastpos[Z_AXIS]));
 			enquecommand(cmd1);
-			enquecommand_P(PSTR("M83")); // set extruder to relative mode.
+			if (axis_relative_modes[3] == true) enquecommand_P(PSTR("M83")); // set extruder to relative mode.
+			else enquecommand_P(PSTR("M82")); // set extruder to absolute mode
 			enquecommand_P(PSTR("G1 E"  STRINGIFY(PAUSE_RETRACT))); //unretract
 			enquecommand_P(PSTR("G90")); //absolute positioning
 			lcd_commands_step = 1;
@@ -2620,7 +2621,7 @@ static void lcd_calibration_menu()
 MENU_ITEM(function, MSG_CALIBRATE_BED, lcd_mesh_calibration);
     // "Calibrate Z" with storing the reference values to EEPROM.
     MENU_ITEM(submenu, MSG_HOMEYZ, lcd_mesh_calibration_z);
-	MENU_ITEM(submenu, MSG_CALIBRATION_PINDA_MENU, lcd_pinda_calibration_menu);
+	
 #ifndef SNMM
 	//MENU_ITEM(function, MSG_CALIBRATE_E, lcd_calibrate_extruder);
 #endif
@@ -2629,6 +2630,7 @@ MENU_ITEM(function, MSG_CALIBRATE_BED, lcd_mesh_calibration);
 #endif
     MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28 W"));
     MENU_ITEM(submenu, MSG_BED_CORRECTION_MENU, lcd_adjust_bed);
+	MENU_ITEM(submenu, MSG_CALIBRATION_PINDA_MENU, lcd_pinda_calibration_menu);
 	MENU_ITEM(submenu, MSG_PID_EXTRUDER, pid_extruder);
     MENU_ITEM(submenu, MSG_SHOW_END_STOPS, menu_show_end_stops);
     MENU_ITEM(gcode, MSG_CALIBRATE_BED_RESET, PSTR("M44"));
@@ -3900,6 +3902,7 @@ static void lcd_selftest()
 		_progress = lcd_selftest_screen(4, _progress, 3, true, 1500);
 		_result = lcd_selfcheck_axis(2, Z_MAX_POS);
 		enquecommand_P(PSTR("G28 W"));
+		enquecommand_P(PSTR("G1 Z15"));
 	}
 
 	if (_result)

Firmware/ultralcd_implementation_hitachi_HD44780.h

@@ -964,7 +964,7 @@ static void lcd_implementation_status_screen()
 				char progress[4];
 				lcd.setCursor(0, 3);
 				lcd_printPGM(MSG_TEMP_CALIBRATION);
-				lcd.setCursor(17, 3);
+				lcd.setCursor(12, 3);
 				sprintf(progress, "%d/6", custom_message_state);
 				lcd.print(progress);
 			}