 3d-gussner
|
0067dc0d9d
Merge branch 'MK3' into MK3_EEPROM_doc
|
4 anos atrás |
|
DRracer
|
73349033d5
Merge pull request #2469 from wavexx/fix_current_pos_init
|
4 anos atrás |
|
DRracer
|
468b0e210c
Merge pull request #2372 from leptun/MK3_fix_verbosity
|
4 anos atrás |
|
3d-gussner
|
2818316366
Started EEPROM Table doxygen documentation
|
4 anos atrás |
|
Yuri D'Elia
|
f1618bfbd6
Initialize current_position correctly during startup
|
4 anos atrás |
|
Yuri D'Elia
|
6fbd632c84
Isolate all PAT9125-specific code, fix build on !MK3 variants
|
4 anos atrás |
|
Yuri D'Elia
|
d47363d85a
Update the filament axis resolution when E resolution is changed
|
4 anos atrás |
|
Yuri D'Elia
|
8fb8ff4bf4
Include fsensor recovery stats in the last print stats
|
5 anos atrás |
|
DRracer
|
007395acb4
Merge pull request #2458 from wavexx/la15_compat
|
4 anos atrás |
|
Yuri D'Elia
|
453f5dd874
Adjust E-jerk in LA10 compatibility mode
|
4 anos atrás |
|
Yuri D'Elia
|
84ecf96be5
Do not clear last print fail stats prematurely
|
4 anos atrás |
|
DRracer
|
d70a147af5
Merge pull request #2436 from leptun/MK3_PSU_DELTA_cleanup
|
4 anos atrás |
|
DRracer
|
1ceadcb162
Merge pull request #2448 from wavexx/save_restore_fix
|
4 anos atrás |
|
DRracer
|
1b7677c768
Merge pull request #2394 from wavexx/fsensor_no_recursion
|
4 anos atrás |
|
Yuri D'Elia
|
1db024f17a
Always raise the extruder 25mm during power recovery
|
4 anos atrás |
|
Yuri D'Elia
|
571906a494
Do not update saved_target if there's no current_block
|
4 anos atrás |
|
Yuri D'Elia
|
02d1525445
Display "POWER PANIC DETECTED" when possible
|
4 anos atrás |
|
Yuri D'Elia
|
2b46fdac2d
Only trigger a quick reset if there's a pending saved state
|
4 anos atrás |
|
Alex Voinea
|
4fd913ddf3
Remove commented out code
|
4 anos atrás |
|
Yuri D'Elia
|
b46dc59fad
Refuse to start a print if power is lost before arming uvlo
|
4 anos atrás |
|
Yuri D'Elia
|
200cdde1af
Setup the UVLO interrupt later during initialization
|
4 anos atrás |
|
Yuri D'Elia
|
3da20db024
Really poweroff Z motors when PSU_Delta is defined
|
4 anos atrás |
|
Yuri D'Elia
|
5d88573711
Save/restore hotend temperatures above 255C in PowerPanic
|
4 anos atrás |
|
Yuri D'Elia
|
50a9fe003a
Bump the unparking speed to 50mm/s (same as M600 recovery)
|
4 anos atrás |
|
Yuri D'Elia
|
eb2ca78167
Rewrite uvlo handling for accurate Z re/positioning
|
4 anos atrás |
|
Yuri D'Elia
|
11a0e95f60
Re-enable the code that moves the extruder during PP
|
4 anos atrás |
|
Yuri D'Elia
|
ec5cbf73b9
During PP keep the watchdog waiting for longer
|
4 anos atrás |
|
Yuri D'Elia
|
ec8b5aaa34
Do not attempt to "zero-phase" the microstep counter
|
4 anos atrás |
|
Yuri D'Elia
|
5310181970
Cancel a recovering print when using the LCD "Stop"
|
4 anos atrás |
|
Alex Voinea
|
4055977a95
Do not clear axis known position when Z is set to silent
|
4 anos atrás |
