 PavelSindler
|
1eeb960f44
Xyz details added to support menu
|
7 tahun lalu |
|
PavelSindler
|
db11abf5e5
T? code initial version
|
7 tahun lalu |
|
PavelSindler
|
362d7ba833
unload filament reverted
|
7 tahun lalu |
|
PavelSindler
|
6af95141f5
xyz calibation improvements: user is informed that front point is not reachable during first cal. phase, more info on serial, arithmetic mean used over iterations, initial points position changed for second ant third iteration
|
7 tahun lalu |
|
PavelSindler
|
7005c6d685
selftest for heater/heatbed thermistor updated (prolonged heating times, changed target temperature for heater)
|
7 tahun lalu |
|
PavelSindler
|
0c4b5795fa
G4: in case that there is no dwell time set, "Sleep..." message is not printed on LCD
|
7 tahun lalu |
|
PavelSindler
|
11a86a6a9a
snmm: M702 (unload filament) extended, snmm stop print: user is asked which filaments to unload
|
7 tahun lalu |
|
PavelSindler
|
bc61622d21
snmm: stop print unloads only used filaments, disable steppers (M84) resets used filaments
|
8 tahun lalu |
|
PavelSindler
|
36091dcde4
M117 command fixed to be able to print strings without restrictions
|
8 tahun lalu |
|
PavelSindler
|
86e4056680
removed unused gcode description
|
8 tahun lalu |
|
PavelSindler
|
e5d10074cf
stop print during auto home and mesh bed leveling improved
|
8 tahun lalu |
|
PavelSindler
|
12f9afce74
tset heatbed target temperature to zero at the end of temp. calibration, before final message is shown
|
8 tahun lalu |
|
PavelSindler
|
8f904f90d0
Italian bed correction messages corrected
|
8 tahun lalu |
|
PavelSindler
|
fefa240cd7
czech messages corrected; temp. calibration: improved serial communication, disable steppers after calibration, preheat phase on start print when running from octoprint,
|
8 tahun lalu |
|
PavelSindler
|
57ef9cf59b
unloading filaments and M600 messages updated
|
8 tahun lalu |
|
PavelSindler
|
bb3887fe1b
calibration status and pinda probe calibration status were split
|
8 tahun lalu |
|
PavelSindler
|
9fdd23aaa5
snmm: czech messages corrected, M600 filament not loaded, timers updated, updated behavior when choosing "change filament" from menu
|
8 tahun lalu |
|
PavelSindler
|
134a50f5b3
messages updated, different bowden lengths for SNMM used, M600 for SNMM updated, stop print for SNMM updated, load all filaments added
|
8 tahun lalu |
|
PavelSindler
|
df9f063f99
snmm: removed detection if print was terminated by reset/blackout; initial version of stop print for snmm
|
8 tahun lalu |
|
PavelSindler
|
2fa97d5dfe
Added messages in czech and english for SNMM, service menu for adjusting bowden lengths; updated service menu to be extendable; M600: loading filament for SNMM updated; unload all filaments updated
|
8 tahun lalu |
|
PavelSindler
|
032f2637a7
adding edits made by akukan
|
8 tahun lalu |
|
PavelSindler
|
32df4f68a1
messages translated, invalidate calibration status at the beginning of temp. calibration
|
8 tahun lalu |
|
PavelSindler
|
397039270a
PINDA Preheating countdown updated
|
8 tahun lalu |
|
PavelSindler
|
50b7f627cd
pinda preheating messages changed
|
8 tahun lalu |
|
PavelSindler
|
7e8780ba61
long press compatible with timeout to status, temp compensation extrapolation, preheat Z coordinate added, G75 for showing interpolation table
|
8 tahun lalu |
|
PavelSindler
|
7ec45271c2
timeout to status, better print time counting when using pause print
|
8 tahun lalu |
|
PavelSindler
|
c03a18f8c3
czech messages added, temperature calibration is off in fresh eeprom, pinda preheat phase is not used unless calibration was run, pause print works with gcode absolute and relative extruder mode, move z higher after selftest
|
8 tahun lalu |
|
PavelSindler
|
329e1ac9bb
waiting for PINDA to cool down
|
8 tahun lalu |
|
PavelSindler
|
4de9b1c9f6
temp calibration on/off initialization when updating firmware
|
8 tahun lalu |
|
PavelSindler
|
70b6e13de4
farm mode activation and farm number initialization handled when upgrading firmware versions and when flashing to new eeprom
|
8 tahun lalu |
