 espr14
|
1610c96fc4
Fix and report circle divergence
|
3 jaren geleden |
|
DRracer
|
eb44ee0f57
Code size optimization: 2KB down (#2687)
|
4 jaren geleden |
|
leptun
|
8c2902a660
Revert "Mesh bed leveling testing"
|
5 jaren geleden |
|
leptun
|
28e812d91f
Mesh bed leveling testing
|
5 jaren geleden |
|
leptun
|
7650e2b60c
Handle disable_heater()
|
5 jaren geleden |
|
leptun
|
570b5989f4
Disable bed PWM while probing bed.
|
5 jaren geleden |
|
DRracer
|
a7c2aec04c
Code size reduced by almost 5KB
|
5 jaren geleden |
|
Marek Bel
|
4a16fe6902
Save z_offset, bed_temp and pinda_temp with sheet calibration.
|
5 jaren geleden |
|
Ondrej Tuma
|
b7fe43bf68
Deleted bad cols/rows definitions for translation.
|
5 jaren geleden |
|
PavelSindler
|
96a111119b
document
|
5 jaren geleden |
|
PavelSindler
|
8f69d5a501
document
|
5 jaren geleden |
|
PavelSindler
|
e259967991
remove / comment debug code
|
5 jaren geleden |
|
PavelSindler
|
5863297538
if deviation between current Z-probe and avg, value > 50um, enlarge Z-probe movements and repeat measurement
|
5 jaren geleden |
|
PavelSindler
|
a9ce38df71
Function for decision if we have valid Z-calibration data in eeprom fixed, mesh bed leveling: possible crash fix, temporaty debug info on serial line.
|
5 jaren geleden |
|
PavelSindler
|
ef198856a4
increase relative movement in Z to work better with higher hysteresis PINDAs
|
5 jaren geleden |
|
PavelSindler
|
9e0e4198c5
Mesh by 3d-gussner, fixed difference between mbl points coordinates and coordinates used in planner for corrections, mbl settings menu update
|
5 jaren geleden |
|
PavelSindler
|
6c70d59810
mbl settings initialization fix
|
5 jaren geleden |
|
PavelSindler
|
0aa21c362e
compile error fix
|
5 jaren geleden |
|
PavelSindler
|
9a83925a97
fixed bug in counting approximate Z coordinate
|
5 jaren geleden |
|
PavelSindler
|
141b78c048
number of Z-probes defualt value changed from 4 to 3, mmu stealth mode switch in settings menu
|
5 jaren geleden |
|
PavelSindler
|
f293d61d3d
faster Z probe: move Z 150um relatively to last measurement. If PINDA is triggered at the beginning of measurement, move Z 500um higher and repeat measurement
|
5 jaren geleden |
|
PavelSindler
|
6a864ffbab
G80 parameters configurable via settings menu
|
5 jaren geleden |
|
PavelSindler
|
7c187541e1
function for valid points determination improved; simple Z-coordinate estimation; measure all points and use inaccurate Z-coordinate in case that we don't have enought information for counting Z-coordinate estimation
|
5 jaren geleden |
|
PavelSindler
|
d9e93e8a77
measurements points moved 10mm to the left; measure only chosen points (e.g. not points affected by magnets proximity)
|
5 jaren geleden |
|
PavelSindler
|
17f095b957
shorter Z movements (makes calibration faster)
|
5 jaren geleden |
|
PavelSindler
|
e27fdafcec
menu switch - initial
|
5 jaren geleden |
|
Laurentiu
|
51827c578f
MESH_MEAS_NUM_X_POINTS constant correction to MESH_MEAS_NUM_Y_POINTS
|
5 jaren geleden |
|
Laurentiu
|
62875f2e95
MESH_MEAS_NUM_X_POINTS constant correction to MESH_MEAS_NUM_Y_POINTS
|
5 jaren geleden |
|
Laurentiu
|
4835b9b220
7x7 points mesh bed leveling
|
5 jaren geleden |
|
Robert Pelnar
|
9a68501039
MK2 variants compilable
|
6 jaren geleden |
