Update translatable strings to match our extraction macros

Update pot and po files

Firmware/mmu2/errors_list.h

@@ -200,7 +200,7 @@ static const char MSG_DESC_FSENSOR_DIDNT_GO_OFF[] PROGMEM_I1 = ISTR("Filament se
 static const char MSG_DESC_PULLEY_STALLED[] PROGMEM_I1 = ISTR("Pulley motor stalled. Ensure the pulley can move and check the wiring."); ////MSG_DESC_PULLEY_STALLED c=20 r=8
 static const char MSG_DESC_FSENSOR_TOO_EARLY[] PROGMEM_I1 = ISTR("Filament sensor triggered too early while loading to extruder. Check there isn't anything stuck in PTFE tube. Check that sensor reads properly."); ////MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
 static const char MSG_DESC_SELECTOR_CANNOT_HOME[] PROGMEM_I1 = ISTR("The Selector cannot home properly. Check for anything blocking its movement."); ////MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-static const char MSG_DESC_CANNOT_MOVE[] PROGMEM_I1 = ISTR(""); // these errors have been disabled
+static const char MSG_DESC_CANNOT_MOVE[] PROGMEM_I1 = ISTR(" "); /////MSG_DESC_CANNOT_MOVE c=20 //these errors have been disabled
 //static const char MSG_DESC_SELECTOR_CANNOT_MOVE[] PROGMEM_I1 = ISTR("The Selector cannot move. Check for anything blocking its movement. Check the wiring is correct.");
 static const char MSG_DESC_IDLER_CANNOT_HOME[] PROGMEM_I1 = ISTR("The Idler cannot home properly. Check for anything blocking its movement."); ////MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
 //static const char MSG_DESC_IDLER_CANNOT_MOVE[] PROGMEM_I1 = ISTR("The Idler cannot move properly. Check for anything blocking its movement. Check the wiring is correct.");
@@ -233,42 +233,42 @@ static const char MSG_DESC_FW_RUNTIME_ERROR[] PROGMEM_I1 = ISTR("Internal runtim
 static const char MSG_DESC_UNLOAD_MANUALLY[] PROGMEM_I1 = ISTR("Unexpected FINDA reading. Ensure no filament is under FINDA and the selector is free. Check FINDA connection."); ////MSG_DESC_UNLOAD_MANUALLY c=20 r=8
 
 static const char * const errorDescs[] PROGMEM = {
-    MSG_DESC_FINDA_DIDNT_TRIGGER,
-    MSG_DESC_FINDA_DIDNT_GO_OFF,
-    MSG_DESC_FSENSOR_DIDNT_TRIGGER,
-    MSG_DESC_FSENSOR_DIDNT_GO_OFF,
-    MSG_DESC_PULLEY_STALLED,
-    MSG_DESC_FSENSOR_TOO_EARLY,
-    MSG_DESC_SELECTOR_CANNOT_HOME,
-    MSG_DESC_CANNOT_MOVE,
-    MSG_DESC_IDLER_CANNOT_HOME,
-    MSG_DESC_CANNOT_MOVE,
-    MSG_DESC_TMC, // descPULLEY_WARNING_TMC_TOO_HOT,
-    MSG_DESC_TMC, // descSELECTOR_WARNING_TMC_TOO_HOT,
-    MSG_DESC_TMC, // descIDLER_WARNING_TMC_TOO_HOT,
-    MSG_DESC_TMC, // descPULLEY_TMC_OVERHEAT_ERROR,
-    MSG_DESC_TMC, // descSELECTOR_TMC_OVERHEAT_ERROR,
-    MSG_DESC_TMC, // descIDLER_TMC_OVERHEAT_ERROR,
-    MSG_DESC_TMC, // descPULLEY_TMC_DRIVER_ERROR,
-    MSG_DESC_TMC, // descSELECTOR_TMC_DRIVER_ERROR,
-    MSG_DESC_TMC, // descIDLER_TMC_DRIVER_ERROR,
-    MSG_DESC_TMC, // descPULLEY_TMC_DRIVER_RESET,
-    MSG_DESC_TMC, // descSELECTOR_TMC_DRIVER_RESET,
-    MSG_DESC_TMC, // descIDLER_TMC_DRIVER_RESET,
-    MSG_DESC_TMC, // descPULLEY_TMC_UNDERVOLTAGE_ERROR,
-    MSG_DESC_TMC, // descSELECTOR_TMC_UNDERVOLTAGE_ERROR,
-    MSG_DESC_TMC, // descIDLER_TMC_UNDERVOLTAGE_ERROR,
-    MSG_DESC_TMC, // descPULLEY_TMC_DRIVER_SHORTED,
-    MSG_DESC_TMC, // descSELECTOR_TMC_DRIVER_SHORTED,
-    MSG_DESC_TMC, // descIDLER_TMC_DRIVER_SHORTED,
-    MSG_DESC_MMU_NOT_RESPONDING,
-    MSG_DESC_COMMUNICATION_ERROR,
-    MSG_DESC_FILAMENT_ALREADY_LOADED,
-    MSG_DESC_INVALID_TOOL,
-    MSG_DESC_QUEUE_FULL,
-    MSG_DESC_FW_UPDATE_NEEDED,
-    MSG_DESC_FW_RUNTIME_ERROR,
-    MSG_DESC_UNLOAD_MANUALLY
+    _R(MSG_DESC_FINDA_DIDNT_TRIGGER),
+    _R(MSG_DESC_FINDA_DIDNT_GO_OFF),
+    _R(MSG_DESC_FSENSOR_DIDNT_TRIGGER),
+    _R(MSG_DESC_FSENSOR_DIDNT_GO_OFF),
+    _R(MSG_DESC_PULLEY_STALLED),
+    _R(MSG_DESC_FSENSOR_TOO_EARLY),
+    _R(MSG_DESC_SELECTOR_CANNOT_HOME),
+    _R(MSG_DESC_CANNOT_MOVE),
+    _R(MSG_DESC_IDLER_CANNOT_HOME),
+    _R(MSG_DESC_CANNOT_MOVE),
+    _R(MSG_DESC_TMC), // descPULLEY_WARNING_TMC_TOO_HOT
+    _R(MSG_DESC_TMC), // descSELECTOR_WARNING_TMC_TOO_HOT
+    _R(MSG_DESC_TMC), // descIDLER_WARNING_TMC_TOO_HOT
+    _R(MSG_DESC_TMC), // descPULLEY_TMC_OVERHEAT_ERROR
+    _R(MSG_DESC_TMC), // descSELECTOR_TMC_OVERHEAT_ERROR
+    _R(MSG_DESC_TMC), // descIDLER_TMC_OVERHEAT_ERROR
+    _R(MSG_DESC_TMC), // descPULLEY_TMC_DRIVER_ERROR
+    _R(MSG_DESC_TMC), // descSELECTOR_TMC_DRIVER_ERROR
+    _R(MSG_DESC_TMC), // descIDLER_TMC_DRIVER_ERROR
+    _R(MSG_DESC_TMC), // descPULLEY_TMC_DRIVER_RESET
+    _R(MSG_DESC_TMC), // descSELECTOR_TMC_DRIVER_RESET
+    _R(MSG_DESC_TMC), // descIDLER_TMC_DRIVER_RESET
+    _R(MSG_DESC_TMC), // descPULLEY_TMC_UNDERVOLTAGE_ERROR
+    _R(MSG_DESC_TMC), // descSELECTOR_TMC_UNDERVOLTAGE_ERROR
+    _R(MSG_DESC_TMC), // descIDLER_TMC_UNDERVOLTAGE_ERROR
+    _R(MSG_DESC_TMC), // descPULLEY_TMC_DRIVER_SHORTED
+    _R(MSG_DESC_TMC), // descSELECTOR_TMC_DRIVER_SHORTED
+    _R(MSG_DESC_TMC), // descIDLER_TMC_DRIVER_SHORTED
+    _R(MSG_DESC_MMU_NOT_RESPONDING),
+    _R(MSG_DESC_COMMUNICATION_ERROR),
+    _R(MSG_DESC_FILAMENT_ALREADY_LOADED),
+    _R(MSG_DESC_INVALID_TOOL),
+    _R(MSG_DESC_QUEUE_FULL),
+    _R(MSG_DESC_FW_UPDATE_NEEDED),
+    _R(MSG_DESC_FW_RUNTIME_ERROR),
+    _R(MSG_DESC_UNLOAD_MANUALLY)
 };
 
 // we have max 3 buttons/operations to select from

lang/po/Firmware.pot

@@ -6,6 +6,13 @@ msgstr ""
 "Content-Type: text/plain; charset=utf-8\n"
 "Content-Transfer-Encoding: 8bit\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -242,7 +249,7 @@ msgid "Calibration done"
 msgstr ""
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid ""
 "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
@@ -549,14 +556,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -690,21 +697,21 @@ msgid "Filament sensor"
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -920,7 +927,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware."
 " If the issue persists, contact support."
@@ -1045,7 +1052,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1077,14 +1084,14 @@ msgid "MMU load fails"
 msgstr ""
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1157,7 +1164,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1618,7 +1634,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1659,7 +1675,7 @@ msgid "Rename"
 msgstr ""
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2043,20 +2059,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2119,7 +2135,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector"
 " is free. Check FINDA connection."

lang/po/Firmware_cs.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -258,7 +265,7 @@ msgid "Calibration done"
 msgstr "Kalibrace OK"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -570,14 +577,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -711,21 +718,21 @@ msgid "Filament sensor"
 msgstr "Senzor filamentu"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -954,7 +961,7 @@ msgid ""
 msgstr "Vlozte filament (nezavadejte) do extruderu a stisknete tlacitko"
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1079,7 +1086,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1111,14 +1118,14 @@ msgid "MMU load fails"
 msgstr "MMU selhani zav"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1191,7 +1198,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1666,7 +1682,7 @@ msgstr ""
 "Tisk zrusen."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1707,7 +1723,7 @@ msgid "Rename"
 msgstr "Prejmenovat"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2099,20 +2115,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2179,7 +2195,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_da.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -251,7 +258,7 @@ msgid "Calibration done"
 msgstr ""
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -557,14 +564,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -698,21 +705,21 @@ msgid "Filament sensor"
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -929,7 +936,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1054,7 +1061,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1086,14 +1093,14 @@ msgid "MMU load fails"
 msgstr ""
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1166,7 +1173,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1627,7 +1643,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1668,7 +1684,7 @@ msgid "Rename"
 msgstr ""
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2052,20 +2068,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2128,7 +2144,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_de.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -258,7 +265,7 @@ msgid "Calibration done"
 msgstr "Kalibrierung OK"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 "Die Aktion kann nicht ausgeführt werden, das Filament ist bereits geladen. "
@@ -574,7 +581,7 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr "FINDA N. AUSGELÖST"
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
@@ -584,7 +591,7 @@ msgstr ""
 "FINDA funktioniert."
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -720,7 +727,7 @@ msgid "Filament sensor"
 msgstr "Filamentsensor"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
@@ -729,7 +736,7 @@ msgstr ""
 "sicher, dass sich das Fil. bewegen kann und der Sensor funktioniert."
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
@@ -739,7 +746,7 @@ msgstr ""
 "funktioniert."
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -975,7 +982,7 @@ msgstr ""
 "den Knopf."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1103,7 +1110,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr "MMU FW UPDATE NÖTIG"
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr "MMU Firmware interner Fehler, bitte setzen Sie die MMU zurück."
 
@@ -1135,7 +1142,7 @@ msgid "MMU load fails"
 msgstr "MMU Ladefehler"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
@@ -1145,7 +1152,7 @@ msgstr ""
 "Support."
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1221,7 +1228,16 @@ msgid "Model"
 msgstr "Modell"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr "Weiter Details online."
 
@@ -1700,7 +1716,7 @@ msgstr ""
 "den Wert in den Einstellungen. Druck abgebrochen."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 "Der Riemenscheiben- motor ist blockiert. Sicherstellen, dass sich die "
@@ -1745,7 +1761,7 @@ msgid "Rename"
 msgstr "Umbenennen"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2141,7 +2157,7 @@ msgid "Testing filament"
 msgstr "Teste filament"
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2149,7 +2165,7 @@ msgstr ""
 "ob irgendetwas seine Bewegung blockiert."
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
@@ -2159,7 +2175,7 @@ msgstr ""
 "neuesten Stand ist."
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2229,7 +2245,7 @@ msgid "UNLOAD MANUALLY"
 msgstr "ENTLADE MANUELL"
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_es.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -257,7 +264,7 @@ msgid "Calibration done"
 msgstr "Calibracion OK"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -570,14 +577,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -711,21 +718,21 @@ msgid "Filament sensor"
 msgstr "Sensor de fil."
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -956,7 +963,7 @@ msgstr ""
 "Inserte el filamento (no lo cargue) en el extrusor y luego presione el dial."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1081,7 +1088,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1113,14 +1120,14 @@ msgid "MMU load fails"
 msgstr "Carga MMU falla"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1193,7 +1200,16 @@ msgid "Model"
 msgstr "Modelo"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1676,7 +1692,7 @@ msgstr ""
 "ajustes. Impresion cancelada."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1719,7 +1735,7 @@ msgid "Rename"
 msgstr "Renombrar"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2118,20 +2134,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2199,7 +2215,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_fr.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -258,7 +265,7 @@ msgid "Calibration done"
 msgstr "Calibration terminee"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -573,14 +580,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -714,21 +721,21 @@ msgid "Filament sensor"
 msgstr "Capteur de fil."
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -963,7 +970,7 @@ msgstr ""
 "appuyez sur le bouton."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1088,7 +1095,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1120,14 +1127,14 @@ msgid "MMU load fails"
 msgstr "Def. charg. MMU"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1200,7 +1207,16 @@ msgid "Model"
 msgstr "Modele"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1680,7 +1696,7 @@ msgstr ""
 "Code. Merci de verifier le parametre dans les reglages. Impression annulee."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1722,7 +1738,7 @@ msgid "Rename"
 msgstr "Renommer"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2119,20 +2135,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2200,7 +2216,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_hr.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -257,7 +264,7 @@ msgid "Calibration done"
 msgstr "Kalibracija gotova"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -568,14 +575,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -709,21 +716,21 @@ msgid "Filament sensor"
 msgstr "Senzor filamenta"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -954,7 +961,7 @@ msgstr ""
 "Umetnite filament (nemojte ga puniti) u ekstruder i zatim pritisnite gumb."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1079,7 +1086,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1111,14 +1118,14 @@ msgid "MMU load fails"
 msgstr "Neusp. MMU punj"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1191,7 +1198,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1665,7 +1681,7 @@ msgstr ""
 "vrijednost u postavkama. Print je otkazan."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1708,7 +1724,7 @@ msgid "Rename"
 msgstr "Preimenuj"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2106,20 +2122,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2186,7 +2202,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_hu.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -257,7 +264,7 @@ msgid "Calibration done"
 msgstr "Kalibracio kesz"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -571,14 +578,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -712,21 +719,21 @@ msgid "Filament sensor"
 msgstr "Filament szenzor"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -958,7 +965,7 @@ msgstr ""
 "gombot."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1083,7 +1090,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1115,14 +1122,14 @@ msgid "MMU load fails"
 msgstr "MMU bet. hibak"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1195,7 +1202,16 @@ msgid "Model"
 msgstr "Modell"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1672,7 +1688,7 @@ msgstr ""
 "beallitasokban. Nyomtatas megallitva."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1715,7 +1731,7 @@ msgid "Rename"
 msgstr "Atnevezes"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2110,20 +2126,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2191,7 +2207,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_it.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -257,7 +264,7 @@ msgid "Calibration done"
 msgstr "Calibr. completa"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -571,14 +578,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -712,21 +719,21 @@ msgid "Filament sensor"
 msgstr "Sensore filam."
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -957,7 +964,7 @@ msgstr ""
 "Inserire filamento (senza caricarlo) nell'estrusore e premere la manopola."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1082,7 +1089,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1114,14 +1121,14 @@ msgid "MMU load fails"
 msgstr "Car MMU falliti"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1194,7 +1201,16 @@ msgid "Model"
 msgstr "Modello"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1670,7 +1686,7 @@ msgstr ""
 "Stampa annullata."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1713,7 +1729,7 @@ msgid "Rename"
 msgstr "Rinomina"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2110,20 +2126,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2191,7 +2207,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_lb.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -251,7 +258,7 @@ msgid "Calibration done"
 msgstr ""
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -557,14 +564,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -698,21 +705,21 @@ msgid "Filament sensor"
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -929,7 +936,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1054,7 +1061,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1086,14 +1093,14 @@ msgid "MMU load fails"
 msgstr ""
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1166,7 +1173,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1627,7 +1643,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1668,7 +1684,7 @@ msgid "Rename"
 msgstr ""
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2052,20 +2068,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2128,7 +2144,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_lt.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -251,7 +258,7 @@ msgid "Calibration done"
 msgstr ""
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -557,14 +564,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -698,21 +705,21 @@ msgid "Filament sensor"
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -929,7 +936,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1054,7 +1061,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1086,14 +1093,14 @@ msgid "MMU load fails"
 msgstr ""
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1166,7 +1173,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1627,7 +1643,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1668,7 +1684,7 @@ msgid "Rename"
 msgstr ""
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2052,20 +2068,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2128,7 +2144,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_nl.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -258,10 +265,11 @@ msgid "Calibration done"
 msgstr "Kalibratie klaar"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
-"De actie kan niet worden uitgevoerd, de filament is al geladen. Eerst uitladen."
+"De actie kan niet worden uitgevoerd, de filament is al geladen. Eerst "
+"uitladen."
 
 #. MSG_SD_REMOVED c=20
 #: ../../Firmware/ultralcd.cpp:7700
@@ -573,16 +581,16 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
-"De FINDA schakelde niet uit bij het lossen. Probeer Fil. handmatig "
-"te ontladen. Controleer of Fil. kan bewegen en of de FINDA werkt."
+"De FINDA schakelde niet uit bij het lossen. Probeer Fil. handmatig te "
+"ontladen. Controleer of Fil. kan bewegen en of de FINDA werkt."
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -718,7 +726,7 @@ msgid "Filament sensor"
 msgstr "Filamentsensor"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
@@ -727,7 +735,7 @@ msgstr ""
 "Controleer of het filament kan bewegen en de sensor werkt."
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
@@ -736,13 +744,13 @@ msgstr ""
 "Controleer of het filament de fsensor heeft bereikt en de sensor werkt."
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
 msgstr ""
-"Filament sensor te vroeg geactiveerd tijdens laden naar extruder. Controleer of "
-"er niets vastzit in de PTFE-buis. Controleer of de sensor goed leest."
+"Filament sensor te vroeg geactiveerd tijdens laden naar extruder. Controleer "
+"of er niets vastzit in de PTFE-buis. Controleer of de sensor goed leest."
 
 #. MSG_FILAMENT_USED c=19
 #: ../../Firmware/ultralcd.cpp:2363
@@ -969,13 +977,13 @@ msgstr ""
 "Steek a.u.b. filament (maar niet laden) in de extruder en druk op knop."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
 msgstr ""
-"Interne runtime fout. Probeer de MMU-eenheid te resetten of de firmware bij te "
-"werken. Als het probleem aanhoudt, neem dan contact op met support."
+"Interne runtime fout. Probeer de MMU-eenheid te resetten of de firmware bij "
+"te werken. Als het probleem aanhoudt, neem dan contact op met support."
 
 #. MSG_FILAMENT_LOADED c=20 r=2
 #: ../../Firmware/messages.cpp:38 ../../Firmware/ultralcd.cpp:3827
@@ -1096,7 +1104,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1128,7 +1136,7 @@ msgid "MMU load fails"
 msgstr "MMU laadfout"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
@@ -1137,7 +1145,7 @@ msgstr ""
 "Als het probleem aanhoudt, neem dan contact op met support."
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1212,7 +1220,16 @@ msgid "Model"
 msgstr "Model"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1690,7 +1707,7 @@ msgstr ""
 "de waarde in de instellingen. Afdrukken geannuleerd."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1732,7 +1749,7 @@ msgid "Rename"
 msgstr "Hernoem"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2132,20 +2149,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2213,7 +2230,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_no.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -258,7 +265,7 @@ msgid "Calibration done"
 msgstr "Kalibrering ferdig"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -571,14 +578,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -712,21 +719,21 @@ msgid "Filament sensor"
 msgstr "Filamentsensor"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -951,7 +958,7 @@ msgid ""
 msgstr "Sett inn filamentet i ekstruderen og deretter trykk inn valghjulet."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1076,7 +1083,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1108,14 +1115,14 @@ msgid "MMU load fails"
 msgstr "MMU lastefeil"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1188,7 +1195,16 @@ msgid "Model"
 msgstr "Modell"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1660,7 +1676,7 @@ msgstr ""
 "hva som er satt. Print avbrutt."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1701,7 +1717,7 @@ msgid "Rename"
 msgstr "Gi nytt navn"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2092,20 +2108,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2173,7 +2189,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_pl.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -257,7 +264,7 @@ msgid "Calibration done"
 msgstr "Kalibracja OK"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -571,14 +578,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -712,21 +719,21 @@ msgid "Filament sensor"
 msgstr "Czujnik filamentu"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -955,7 +962,7 @@ msgstr ""
 "pokretlo."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1080,7 +1087,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1112,14 +1119,14 @@ msgid "MMU load fails"
 msgstr "Bledy lad. MMU"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1192,7 +1199,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1667,7 +1683,7 @@ msgstr ""
 "Srednica dyszy rozni sie od tej w G-code. Sprawdz ustawienia. Druk anulowany."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1708,7 +1724,7 @@ msgid "Rename"
 msgstr "Zmien nazwe"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2105,20 +2121,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2186,7 +2202,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_ro.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -259,7 +266,7 @@ msgid "Calibration done"
 msgstr "Calibrare gata"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -572,14 +579,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -713,21 +720,21 @@ msgid "Filament sensor"
 msgstr "Senz. de filament"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -956,7 +963,7 @@ msgid ""
 msgstr "Infige filamentul (nu-l incarca) in extruder si apasa butonul."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1081,7 +1088,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1113,14 +1120,14 @@ msgid "MMU load fails"
 msgstr "Err. incarc MMU"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1193,7 +1200,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1668,7 +1684,7 @@ msgstr ""
 "valoarea in setari. Print anulat."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1710,7 +1726,7 @@ msgid "Rename"
 msgstr "Redenumeste"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2107,20 +2123,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2187,7 +2203,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_sk.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -257,7 +264,7 @@ msgid "Calibration done"
 msgstr "Kalibracia OK"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -570,14 +577,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -711,21 +718,21 @@ msgid "Filament sensor"
 msgstr "Senzor filamentu"
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -953,7 +960,7 @@ msgid ""
 msgstr "Vlozte filament (nezavadzajte) do extruderu a stlacte tlacidlo"
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1078,7 +1085,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1110,14 +1117,14 @@ msgid "MMU load fails"
 msgstr "MMU zlyhalo"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1190,7 +1197,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1666,7 +1682,7 @@ msgstr ""
 "Tlac zrusena."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1707,7 +1723,7 @@ msgid "Rename"
 msgstr "Premenovat"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2099,20 +2115,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2179,7 +2195,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_sl.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -251,7 +258,7 @@ msgid "Calibration done"
 msgstr ""
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -557,14 +564,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -698,21 +705,21 @@ msgid "Filament sensor"
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -929,7 +936,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1054,7 +1061,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1086,14 +1093,14 @@ msgid "MMU load fails"
 msgstr ""
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1166,7 +1173,16 @@ msgid "Model"
 msgstr ""
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1627,7 +1643,7 @@ msgid ""
 msgstr ""
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1668,7 +1684,7 @@ msgid "Rename"
 msgstr ""
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2052,20 +2068,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2128,7 +2144,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."

lang/po/Firmware_sv.po

@@ -15,6 +15,13 @@ msgstr ""
 "X-Poedit-SourceCharset: UTF-8\n"
 "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"
 
+#. MSG_DESC_CANNOT_MOVE c=20
+#. these errors have been disabled
+#: ../../Firmware/mmu2/errors_list.h:203 ../../Firmware/mmu2/errors_list.h:243
+#: ../../Firmware/mmu2/errors_list.h:245
+msgid " "
+msgstr ""
+
 #. MSG_IR_03_OR_OLDER c=18
 #: ../../Firmware/Filament_sensor.cpp:287
 #: ../../Firmware/Filament_sensor.cpp:362 ../../Firmware/messages.cpp:165
@@ -258,7 +265,7 @@ msgid "Calibration done"
 msgstr "Kalibraring utförd"
 
 #. MSG_DESC_FILAMENT_ALREADY_LOADED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:228
+#: ../../Firmware/mmu2/errors_list.h:228 ../../Firmware/mmu2/errors_list.h:266
 msgid "Cannot perform the action, filament is already loaded. Unload it first."
 msgstr ""
 
@@ -571,14 +578,14 @@ msgid "FINDA DIDNT TRIGGER"
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:197
+#: ../../Firmware/mmu2/errors_list.h:197 ../../Firmware/mmu2/errors_list.h:237
 msgid ""
 "FINDA didn't switch off while unloading filament. Try unloading manually. "
 "Ensure filament can move and FINDA works."
 msgstr ""
 
 #. MSG_DESC_FINDA_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:196
+#: ../../Firmware/mmu2/errors_list.h:196 ../../Firmware/mmu2/errors_list.h:236
 msgid ""
 "FINDA didn't trigger while loading the filament. Ensure the filament can "
 "move and FINDA works."
@@ -712,21 +719,21 @@ msgid "Filament sensor"
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_GO_OFF c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:199
+#: ../../Firmware/mmu2/errors_list.h:199 ../../Firmware/mmu2/errors_list.h:239
 msgid ""
 "Filament sensor didn't switch off while unloading filament. Ensure filament "
 "can move and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_DIDNT_TRIGGER c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:198
+#: ../../Firmware/mmu2/errors_list.h:198 ../../Firmware/mmu2/errors_list.h:238
 msgid ""
 "Filament sensor didn't trigger while loading the filament. Ensure the "
 "filament reached the fsensor and the sensor works."
 msgstr ""
 
 #. MSG_DESC_FSENSOR_TOO_EARLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:201
+#: ../../Firmware/mmu2/errors_list.h:201 ../../Firmware/mmu2/errors_list.h:241
 msgid ""
 "Filament sensor triggered too early while loading to extruder. Check there "
 "isn't anything stuck in PTFE tube. Check that sensor reads properly."
@@ -958,7 +965,7 @@ msgstr ""
 "Infoga filamentet (ladda inte in det) i extrudern och tryck sedan på knappen."
 
 #. MSG_DESC_FW_RUNTIME_ERROR c=20 r=11
-#: ../../Firmware/mmu2/errors_list.h:232
+#: ../../Firmware/mmu2/errors_list.h:232 ../../Firmware/mmu2/errors_list.h:270
 msgid ""
 "Internal runtime error. Try resetting the MMU unit or updating the firmware. "
 "If the issue persists, contact support."
@@ -1083,7 +1090,7 @@ msgid "MMU FW UPDATE NEEDED"
 msgstr ""
 
 #. MSG_DESC_QUEUE_FULL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:230
+#: ../../Firmware/mmu2/errors_list.h:230 ../../Firmware/mmu2/errors_list.h:268
 msgid "MMU Firmware internal error, please reset the MMU."
 msgstr ""
 
@@ -1115,14 +1122,14 @@ msgid "MMU load fails"
 msgstr "MMU-laddn felar"
 
 #. MSG_DESC_COMMUNICATION_ERROR c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:227
+#: ../../Firmware/mmu2/errors_list.h:227 ../../Firmware/mmu2/errors_list.h:265
 msgid ""
 "MMU unit not responding correctly. Check the wiring and connectors. If the "
 "issue persists, contact support."
 msgstr ""
 
 #. MSG_DESC_MMU_NOT_RESPONDING c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:226
+#: ../../Firmware/mmu2/errors_list.h:226 ../../Firmware/mmu2/errors_list.h:264
 msgid ""
 "MMU unit not responding. Check the wiring and connectors. If the issue "
 "persists, contact support."
@@ -1195,7 +1202,16 @@ msgid "Model"
 msgstr "Modell"
 
 #. MSG_DESC_TMC c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:207
+#: ../../Firmware/mmu2/errors_list.h:207 ../../Firmware/mmu2/errors_list.h:246
+#: ../../Firmware/mmu2/errors_list.h:247 ../../Firmware/mmu2/errors_list.h:248
+#: ../../Firmware/mmu2/errors_list.h:249 ../../Firmware/mmu2/errors_list.h:250
+#: ../../Firmware/mmu2/errors_list.h:251 ../../Firmware/mmu2/errors_list.h:252
+#: ../../Firmware/mmu2/errors_list.h:253 ../../Firmware/mmu2/errors_list.h:254
+#: ../../Firmware/mmu2/errors_list.h:255 ../../Firmware/mmu2/errors_list.h:256
+#: ../../Firmware/mmu2/errors_list.h:257 ../../Firmware/mmu2/errors_list.h:258
+#: ../../Firmware/mmu2/errors_list.h:259 ../../Firmware/mmu2/errors_list.h:260
+#: ../../Firmware/mmu2/errors_list.h:261 ../../Firmware/mmu2/errors_list.h:262
+#: ../../Firmware/mmu2/errors_list.h:263
 msgid "More details online."
 msgstr ""
 
@@ -1673,7 +1689,7 @@ msgstr ""
 "inställningarna. Utskriften avbröts."
 
 #. MSG_DESC_PULLEY_STALLED c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:200
+#: ../../Firmware/mmu2/errors_list.h:200 ../../Firmware/mmu2/errors_list.h:240
 msgid "Pulley motor stalled. Ensure the pulley can move and check the wiring."
 msgstr ""
 
@@ -1716,7 +1732,7 @@ msgid "Rename"
 msgstr "Döp om"
 
 #. MSG_DESC_INVALID_TOOL c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:229
+#: ../../Firmware/mmu2/errors_list.h:229 ../../Firmware/mmu2/errors_list.h:267
 msgid ""
 "Requested filament tool is not available on this hardware. Check the G-code "
 "for tool index out of range (T0-T4)."
@@ -2110,20 +2126,20 @@ msgid "Testing filament"
 msgstr ""
 
 #. MSG_DESC_IDLER_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:205
+#: ../../Firmware/mmu2/errors_list.h:205 ../../Firmware/mmu2/errors_list.h:244
 msgid ""
 "The Idler cannot home properly. Check for anything blocking its movement."
 msgstr ""
 
 #. MSG_DESC_FW_UPDATE_NEEDED c=20 r=9
-#: ../../Firmware/mmu2/errors_list.h:231
+#: ../../Firmware/mmu2/errors_list.h:231 ../../Firmware/mmu2/errors_list.h:269
 msgid ""
 "The MMU unit reports its FW version incompatible with the printer's "
 "firmware. Make sure the MMU firmware is up to date."
 msgstr ""
 
 #. MSG_DESC_SELECTOR_CANNOT_HOME c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:202
+#: ../../Firmware/mmu2/errors_list.h:202 ../../Firmware/mmu2/errors_list.h:242
 msgid ""
 "The Selector cannot home properly. Check for anything blocking its movement."
 msgstr ""
@@ -2190,7 +2206,7 @@ msgid "UNLOAD MANUALLY"
 msgstr ""
 
 #. MSG_DESC_UNLOAD_MANUALLY c=20 r=8
-#: ../../Firmware/mmu2/errors_list.h:233
+#: ../../Firmware/mmu2/errors_list.h:233 ../../Firmware/mmu2/errors_list.h:271
 msgid ""
 "Unexpected FINDA reading. Ensure no filament is under FINDA and the selector "
 "is free. Check FINDA connection."