 PavelSindler
|
7306e08471
Merge pull request #215 from PavelSindler/sorting
|
7 jaren geleden |
|
PavelSindler
|
a280447610
improved progress bar, use bubble sort, sort switch moved to settings menu, manage heater, host keepalive messages, timeout prolonged, setup screen improved
|
7 jaren geleden |
|
PavelSindler
|
9e1a61cebc
initial version
|
7 jaren geleden |
|
XPila
|
9a1ecd5f48
Merge branch 'MK2' into filecheck
|
7 jaren geleden |
|
PavelSindler
|
77937ab4bb
wizard :checking if PLA is loaded, user can repeat v2 cal., M117 and M1 hotfix
|
7 jaren geleden |
|
PavelSindler
|
34a1a4d4c7
messages corrected
|
7 jaren geleden |
|
PavelSindler
|
61592f9bfa
initial version
|
7 jaren geleden |
|
PavelSindler
|
e52e8e21b1
initial version of wizard
|
7 jaren geleden |
|
PavelSindler
|
a9e02eb23b
added messages
|
7 jaren geleden |
|
PavelSindler
|
d56db4638c
sorting by creation time, progress bar, sorting type swith
|
8 jaren geleden |
|
PavelSindler
|
df342c646d
dont show message that default settings are used if user has never run M500
|
8 jaren geleden |
|
PavelSindler
|
625b8acc8e
eeprom version for multimaterial changed, show message that hardcoded default settings were loaded during printer setup, improved scrolling in sd card menu
|
8 jaren geleden |
|
PavelSindler
|
2ace5fc827
tranlations of support menu, retrieving settings from eeprom changed to exclude E steps per unit
|
8 jaren geleden |
|
PavelSindler
|
247e1bc1e3
change extruder messages translations
|
8 jaren geleden |
|
PavelSindler
|
db11abf5e5
T? code initial version
|
8 jaren geleden |
|
PavelSindler
|
2be567c0d3
snmm: stop print menu messages updated
|
8 jaren geleden |
|
PavelSindler
|
1e734d361a
selftest static memory error fixed; snmm: updated stop print messages
|
8 jaren geleden |
|
PavelSindler
|
11a86a6a9a
snmm: M702 (unload filament) extended, snmm stop print: user is asked which filaments to unload
|
8 jaren geleden |
|
PavelSindler
|
6d7127cf1c
messages translated, readded changing extruder from menu
|
8 jaren geleden |
|
PavelSindler
|
fefa240cd7
czech messages corrected; temp. calibration: improved serial communication, disable steppers after calibration, preheat phase on start print when running from octoprint,
|
8 jaren geleden |
|
PavelSindler
|
7c2caa0fec
prepare filament message in english, bowden menu updated
|
8 jaren geleden |
|
PavelSindler
|
1db5b43175
snmm: bowden length menu updated
|
8 jaren geleden |
|
PavelSindler
|
134a50f5b3
messages updated, different bowden lengths for SNMM used, M600 for SNMM updated, stop print for SNMM updated, load all filaments added
|
8 jaren geleden |
|
PavelSindler
|
2fa97d5dfe
Added messages in czech and english for SNMM, service menu for adjusting bowden lengths; updated service menu to be extendable; M600: loading filament for SNMM updated; unload all filaments updated
|
8 jaren geleden |
|
PavelSindler
|
32df4f68a1
messages translated, invalidate calibration status at the beginning of temp. calibration
|
8 jaren geleden |
|
PavelSindler
|
397039270a
PINDA Preheating countdown updated
|
8 jaren geleden |
|
PavelSindler
|
50b7f627cd
pinda preheating messages changed
|
8 jaren geleden |
|
PavelSindler
|
7e8780ba61
long press compatible with timeout to status, temp compensation extrapolation, preheat Z coordinate added, G75 for showing interpolation table
|
8 jaren geleden |
|
PavelSindler
|
c03a18f8c3
czech messages added, temperature calibration is off in fresh eeprom, pinda preheat phase is not used unless calibration was run, pause print works with gcode absolute and relative extruder mode, move z higher after selftest
|
8 jaren geleden |
|
PavelSindler
|
fc221fbea5
Merged PINDA temp calibration branch into MK2
|
8 jaren geleden |
