 PavelSindler
|
7306e08471
Merge pull request #215 from PavelSindler/sorting
|
7 lat temu |
|
PavelSindler
|
a280447610
improved progress bar, use bubble sort, sort switch moved to settings menu, manage heater, host keepalive messages, timeout prolonged, setup screen improved
|
7 lat temu |
|
PavelSindler
|
9e1a61cebc
initial version
|
7 lat temu |
|
XPila
|
9a1ecd5f48
Merge branch 'MK2' into filecheck
|
7 lat temu |
|
PavelSindler
|
77937ab4bb
wizard :checking if PLA is loaded, user can repeat v2 cal., M117 and M1 hotfix
|
7 lat temu |
|
PavelSindler
|
34a1a4d4c7
messages corrected
|
7 lat temu |
|
PavelSindler
|
61592f9bfa
initial version
|
7 lat temu |
|
PavelSindler
|
e52e8e21b1
initial version of wizard
|
7 lat temu |
|
PavelSindler
|
a9e02eb23b
added messages
|
7 lat temu |
|
PavelSindler
|
d56db4638c
sorting by creation time, progress bar, sorting type swith
|
7 lat temu |
|
PavelSindler
|
df342c646d
dont show message that default settings are used if user has never run M500
|
7 lat temu |
|
PavelSindler
|
625b8acc8e
eeprom version for multimaterial changed, show message that hardcoded default settings were loaded during printer setup, improved scrolling in sd card menu
|
7 lat temu |
|
PavelSindler
|
2ace5fc827
tranlations of support menu, retrieving settings from eeprom changed to exclude E steps per unit
|
7 lat temu |
|
PavelSindler
|
247e1bc1e3
change extruder messages translations
|
7 lat temu |
|
PavelSindler
|
db11abf5e5
T? code initial version
|
7 lat temu |
|
PavelSindler
|
2be567c0d3
snmm: stop print menu messages updated
|
7 lat temu |
|
PavelSindler
|
1e734d361a
selftest static memory error fixed; snmm: updated stop print messages
|
7 lat temu |
|
PavelSindler
|
11a86a6a9a
snmm: M702 (unload filament) extended, snmm stop print: user is asked which filaments to unload
|
7 lat temu |
|
PavelSindler
|
6d7127cf1c
messages translated, readded changing extruder from menu
|
8 lat temu |
|
PavelSindler
|
fefa240cd7
czech messages corrected; temp. calibration: improved serial communication, disable steppers after calibration, preheat phase on start print when running from octoprint,
|
8 lat temu |
|
PavelSindler
|
7c2caa0fec
prepare filament message in english, bowden menu updated
|
8 lat temu |
|
PavelSindler
|
1db5b43175
snmm: bowden length menu updated
|
8 lat temu |
|
PavelSindler
|
134a50f5b3
messages updated, different bowden lengths for SNMM used, M600 for SNMM updated, stop print for SNMM updated, load all filaments added
|
8 lat temu |
|
PavelSindler
|
2fa97d5dfe
Added messages in czech and english for SNMM, service menu for adjusting bowden lengths; updated service menu to be extendable; M600: loading filament for SNMM updated; unload all filaments updated
|
8 lat temu |
|
PavelSindler
|
32df4f68a1
messages translated, invalidate calibration status at the beginning of temp. calibration
|
8 lat temu |
|
PavelSindler
|
397039270a
PINDA Preheating countdown updated
|
8 lat temu |
|
PavelSindler
|
50b7f627cd
pinda preheating messages changed
|
8 lat temu |
|
PavelSindler
|
7e8780ba61
long press compatible with timeout to status, temp compensation extrapolation, preheat Z coordinate added, G75 for showing interpolation table
|
8 lat temu |
|
PavelSindler
|
c03a18f8c3
czech messages added, temperature calibration is off in fresh eeprom, pinda preheat phase is not used unless calibration was run, pause print works with gcode absolute and relative extruder mode, move z higher after selftest
|
8 lat temu |
|
PavelSindler
|
fc221fbea5
Merged PINDA temp calibration branch into MK2
|
8 lat temu |
