Merge remote-tracking branch 'upstream/MK3' into translations-doc

Firmware/Configuration.h

@@ -17,7 +17,7 @@ extern PGM_P sPrinterName;
 
 // Firmware version
 #define FW_VERSION "3.8.0"
-#define FW_COMMIT_NR   2608
+#define FW_COMMIT_NR   2684
 // FW_VERSION_UNKNOWN means this is an unofficial build.
 // The firmware should only be checked into github with this symbol.
 #define FW_DEV_VERSION FW_VERSION_UNKNOWN
@@ -113,11 +113,6 @@ extern PGM_P sPrinterName;
 // #define PS_DEFAULT_OFF
 
 
-
-// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
-//#define TEMP_SENSOR_1_AS_REDUNDANT
-#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
-
 // Actual temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 3  // (seconds)
 #define TEMP_HYSTERESIS 5       // (degC) range of +/- temperatures considered "close" to the target one
@@ -291,6 +286,8 @@ your extruder heater takes 2 minutes to hit the target on heating.
 
 #define Z_HEIGHT_HIDE_LIVE_ADJUST_MENU 2.0f
 
+#define HOME_Z_SEARCH_THRESHOLD 0.15f             // Threshold of the Z height in calibration
+
 //============================= Bed Auto Leveling ===========================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

Firmware/Configuration_adv.h

@@ -10,14 +10,6 @@
 #endif
 #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control
 
-//// Heating sanity check:
-// This waits for the watch period in milliseconds whenever an M104 or M109 increases the target temperatureLCD_PROGRESS_BAR
-// If the temperature has not increased at the end of that period, the target temperature is set to zero.
-// It can be reset with another M104/M109. This check is also only triggered if the target temperature and the current temperature
-//  differ by at least 2x WATCH_TEMP_INCREASE
-//#define WATCH_TEMP_PERIOD 40000 //40 seconds
-//#define WATCH_TEMP_INCREASE 10  //Heat up at least 10 degree in 20 seconds
-
 #ifdef PIDTEMP
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
   // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@@ -400,10 +392,6 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 //=============================  Define Defines  ============================
 //===========================================================================
 
-#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
-  #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
-#endif
-
 #if EXTRUDERS > 1 && defined HEATERS_PARALLEL
   #error "You cannot use HEATERS_PARALLEL if EXTRUDERS > 1"
 #endif

Firmware/Marlin.h

@@ -308,11 +308,6 @@ extern bool axis_known_position[3];
 extern int fanSpeed;
 extern int8_t lcd_change_fil_state;
 
-const char smooth1[] PROGMEM = "Smooth1";
-const char smooth2[] PROGMEM = "Smooth2";
-const char textured[] PROGMEM = "Textur1";
-const char *const defaultSheetNames[] PROGMEM = {smooth1,smooth2,textured};
-
 #ifdef TMC2130
 void homeaxis(int axis, uint8_t cnt = 1, uint8_t* pstep = 0);
 #else

Firmware/Marlin_main.cpp

@@ -524,24 +524,6 @@ bool fans_check_enabled = true;
 
 #ifdef TMC2130
 
-extern int8_t CrashDetectMenu;
-
-void crashdet_enable()
-{
-	tmc2130_sg_stop_on_crash = true;
-	eeprom_update_byte((uint8_t*)EEPROM_CRASH_DET, 0xFF); 
-	CrashDetectMenu = 1;
-
-}
-
-void crashdet_disable()
-{
-	tmc2130_sg_stop_on_crash = false;
-	tmc2130_sg_crash = 0;
-	eeprom_update_byte((uint8_t*)EEPROM_CRASH_DET, 0x00); 
-	CrashDetectMenu = 0;
-}
-
 void crashdet_stop_and_save_print()
 {
 	stop_and_save_print_to_ram(10, -default_retraction); //XY - no change, Z 10mm up, E -1mm retract
@@ -631,7 +613,7 @@ void crashdet_detected(uint8_t mask)
 void crashdet_recover()
 {
 	crashdet_restore_print_and_continue();
-	tmc2130_sg_stop_on_crash = true;
+	if (lcd_crash_detect_enabled()) tmc2130_sg_stop_on_crash = true;
 }
 
 void crashdet_cancel()
@@ -1262,15 +1244,15 @@ void setup()
 	uint8_t silentMode = eeprom_read_byte((uint8_t*)EEPROM_SILENT);
 	if (silentMode == 0xff) silentMode = 0;
 	tmc2130_mode = TMC2130_MODE_NORMAL;
-	uint8_t crashdet = eeprom_read_byte((uint8_t*)EEPROM_CRASH_DET);
-	if (crashdet && !farm_mode)
+
+	if (lcd_crash_detect_enabled() && !farm_mode)
 	{
-		crashdet_enable();
+		lcd_crash_detect_enable();
 	    puts_P(_N("CrashDetect ENABLED!"));
 	}
 	else
 	{
-		crashdet_disable();
+	    lcd_crash_detect_disable();
 	    puts_P(_N("CrashDetect DISABLED"));
 	}
 
@@ -2025,14 +2007,14 @@ static void do_blocking_move_to(float x, float y, float z) {
     feedrate = homing_feedrate[Z_AXIS];
 
     current_position[Z_AXIS] = z;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate/60, active_extruder);
+    plan_buffer_line_curposXYZE(feedrate/60, active_extruder);
     st_synchronize();
 
     feedrate = XY_TRAVEL_SPEED;
 
     current_position[X_AXIS] = x;
     current_position[Y_AXIS] = y;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate/60, active_extruder);
+    plan_buffer_line_curposXYZE(feedrate/60, active_extruder);
     st_synchronize();
 
     feedrate = oldFeedRate;
@@ -2362,77 +2344,77 @@ void ramming() {
 
 		max_feedrate[E_AXIS] = 50;
 		//current_position[E_AXIS] -= 8;
-		//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2100 / 60, active_extruder);
+		//plan_buffer_line_curposXYZE(2100 / 60, active_extruder);
 		//current_position[E_AXIS] += 8;
-		//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2100 / 60, active_extruder);
+		//plan_buffer_line_curposXYZE(2100 / 60, active_extruder);
 		current_position[E_AXIS] += 5.4;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2800 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(2800 / 60, active_extruder);
 		current_position[E_AXIS] += 3.2;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 		current_position[E_AXIS] += 3;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3400 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(3400 / 60, active_extruder);
 		st_synchronize();
 		max_feedrate[E_AXIS] = 80;
 		current_position[E_AXIS] -= 82;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 9500 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(9500 / 60, active_extruder);
 		max_feedrate[E_AXIS] = 50;//tmp[E_AXIS];
 		current_position[E_AXIS] -= 20;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 1200 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(1200 / 60, active_extruder);
 		current_position[E_AXIS] += 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(400 / 60, active_extruder);
 		current_position[E_AXIS] += 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		current_position[E_AXIS] -= 10;
 		st_synchronize();
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		current_position[E_AXIS] += 10;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		current_position[E_AXIS] -= 10;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 800 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(800 / 60, active_extruder);
 		current_position[E_AXIS] += 10;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 800 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(800 / 60, active_extruder);
 		current_position[E_AXIS] -= 10;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 800 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(800 / 60, active_extruder);
 		st_synchronize();
 	}
 	else {
 		//ABS
 		max_feedrate[E_AXIS] = 50;
 		//current_position[E_AXIS] -= 8;
-		//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2100 / 60, active_extruder);
+		//plan_buffer_line_curposXYZE(2100 / 60, active_extruder);
 		//current_position[E_AXIS] += 8;
-		//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2100 / 60, active_extruder);
+		//plan_buffer_line_curposXYZE(2100 / 60, active_extruder);
 		current_position[E_AXIS] += 3.1;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2000 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(2000 / 60, active_extruder);
 		current_position[E_AXIS] += 3.1;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2500 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(2500 / 60, active_extruder);
 		current_position[E_AXIS] += 4;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 		st_synchronize();
 		//current_position[X_AXIS] += 23; //delay
-		//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600/60, active_extruder); //delay
+		//plan_buffer_line_curposXYZE(600/60, active_extruder); //delay
 		//current_position[X_AXIS] -= 23; //delay
-		//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600/60, active_extruder); //delay
+		//plan_buffer_line_curposXYZE(600/60, active_extruder); //delay
 		_delay(4700);
 		max_feedrate[E_AXIS] = 80;
 		current_position[E_AXIS] -= 92;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 9900 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(9900 / 60, active_extruder);
 		max_feedrate[E_AXIS] = 50;//tmp[E_AXIS];
 		current_position[E_AXIS] -= 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 800 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(800 / 60, active_extruder);
 		current_position[E_AXIS] += 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(400 / 60, active_extruder);
 		current_position[E_AXIS] -= 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		st_synchronize();
 		current_position[E_AXIS] += 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		current_position[E_AXIS] -= 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		current_position[E_AXIS] += 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		current_position[E_AXIS] -= 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(600 / 60, active_extruder);
 		st_synchronize();
 
 	}
@@ -2491,7 +2473,7 @@ static void gcode_G28(bool home_x_axis, long home_x_value, bool home_y_axis, lon
 	if (home_all_axes) {
 		current_position[Z_AXIS] += MESH_HOME_Z_SEARCH;
 		feedrate = homing_feedrate[Z_AXIS];
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate / 60, active_extruder);
+		plan_buffer_line_curposXYZE(feedrate / 60, active_extruder);
 		st_synchronize();
 	}
 #ifdef ENABLE_AUTO_BED_LEVELING
@@ -2809,7 +2791,7 @@ bool gcode_M45(bool onlyZ, int8_t verbosity_level)
 	enable_endstops(false);
 	current_position[X_AXIS] += 5;
 	current_position[Y_AXIS] += 5;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 40, active_extruder);
+	plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 40, active_extruder);
 	st_synchronize();
 
 	// Let the user move the Z axes up to the end stoppers.
@@ -2859,7 +2841,7 @@ bool gcode_M45(bool onlyZ, int8_t verbosity_level)
 			
 		bool endstops_enabled  = enable_endstops(false);
         current_position[Z_AXIS] -= 1; //move 1mm down with disabled endstop
-        plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 40, active_extruder);
+        plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 40, active_extruder);
         st_synchronize();
 
 		// Move the print head close to the bed.
@@ -2870,7 +2852,7 @@ bool gcode_M45(bool onlyZ, int8_t verbosity_level)
 		tmc2130_home_enter(Z_AXIS_MASK);
 #endif //TMC2130
 
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 40, active_extruder);
+		plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 40, active_extruder);
 
 		st_synchronize();
 #ifdef TMC2130
@@ -2878,7 +2860,8 @@ bool gcode_M45(bool onlyZ, int8_t verbosity_level)
 #endif //TMC2130
 		enable_endstops(endstops_enabled);
 
-		if (st_get_position_mm(Z_AXIS) == MESH_HOME_Z_SEARCH)
+		if ((st_get_position_mm(Z_AXIS) <= (MESH_HOME_Z_SEARCH + HOME_Z_SEARCH_THRESHOLD)) &&
+		    (st_get_position_mm(Z_AXIS) >= (MESH_HOME_Z_SEARCH - HOME_Z_SEARCH_THRESHOLD)))
 		{
 			if (onlyZ)
 			{
@@ -2910,7 +2893,7 @@ bool gcode_M45(bool onlyZ, int8_t verbosity_level)
 				clean_up_after_endstop_move(l_feedmultiply);
 				// Print head up.
 				current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 40, active_extruder);
+				plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 40, active_extruder);
 				st_synchronize();
 //#ifndef NEW_XYZCAL
 				if (result >= 0)
@@ -2930,7 +2913,7 @@ bool gcode_M45(bool onlyZ, int8_t verbosity_level)
 					clean_up_after_endstop_move(l_feedmultiply);
 					// Print head up.
 					current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-					plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 40, active_extruder);
+					plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 40, active_extruder);
 					st_synchronize();
 					// if (result >= 0) babystep_apply();					
 					#endif //HEATBED_V2
@@ -3040,21 +3023,18 @@ static void gcode_M600(bool automatic, float x_position, float y_position, float
 
     //Retract E
     current_position[E_AXIS] += e_shift;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-            current_position[E_AXIS], FILAMENTCHANGE_RFEED, active_extruder);
+    plan_buffer_line_curposXYZE(FILAMENTCHANGE_RFEED, active_extruder);
     st_synchronize();
 
     //Lift Z
     current_position[Z_AXIS] += z_shift;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-            current_position[E_AXIS], FILAMENTCHANGE_ZFEED, active_extruder);
+    plan_buffer_line_curposXYZE(FILAMENTCHANGE_ZFEED, active_extruder);
     st_synchronize();
 
     //Move XY to side
     current_position[X_AXIS] = x_position;
     current_position[Y_AXIS] = y_position;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-            current_position[E_AXIS], FILAMENTCHANGE_XYFEED, active_extruder);
+    plan_buffer_line_curposXYZE(FILAMENTCHANGE_XYFEED, active_extruder);
     st_synchronize();
 
     //Beep, manage nozzle heater and wait for user to start unload filament
@@ -3079,8 +3059,7 @@ static void gcode_M600(bool automatic, float x_position, float y_position, float
 			lcd_set_cursor(0, 2);
 			lcd_puts_P(_T(MSG_PLEASE_WAIT));
 			current_position[X_AXIS] -= 100;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-				current_position[E_AXIS], FILAMENTCHANGE_XYFEED, active_extruder);
+			plan_buffer_line_curposXYZE(FILAMENTCHANGE_XYFEED, active_extruder);
 			st_synchronize();
 			lcd_show_fullscreen_message_and_wait_P(_i("Please open idler and remove filament manually."));////MSG_CHECK_IDLER c=20 r=4
         }
@@ -3117,8 +3096,7 @@ static void gcode_M600(bool automatic, float x_position, float y_position, float
     if (!automatic)
     {
         current_position[E_AXIS] += FILAMENTCHANGE_RECFEED;
-        plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-                current_position[E_AXIS], FILAMENTCHANGE_EXFEED, active_extruder);
+        plan_buffer_line_curposXYZE(FILAMENTCHANGE_EXFEED, active_extruder);
     }
 
     //Move XY back
@@ -3185,12 +3163,12 @@ void gcode_M701()
 
 		lcd_setstatuspgm(_T(MSG_LOADING_FILAMENT));
 		current_position[E_AXIS] += 40;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400 / 60, active_extruder); //fast sequence
+		plan_buffer_line_curposXYZE(400 / 60, active_extruder); //fast sequence
 		st_synchronize();
 
 		marlin_rise_z();
 		current_position[E_AXIS] += 30;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400 / 60, active_extruder); //fast sequence
+		plan_buffer_line_curposXYZE(400 / 60, active_extruder); //fast sequence
 		
 		load_filament_final_feed(); //slow sequence
 		st_synchronize();
@@ -3284,7 +3262,7 @@ static void gcode_PRUSA_SN()
 //! May be that's why the bad RAMBo's still produce some fan RPM reading, but not corresponding to reality
 static void gcode_PRUSA_BadRAMBoFanTest(){
     //printf_P(PSTR("Enter fan pin test\n"));
-#if !defined(DEBUG_DISABLE_FANCHECK) && defined(FANCHECK) && defined(TACH_1) && TACH_1 >-1 && defined(IR_SENSOR)
+#if !defined(DEBUG_DISABLE_FANCHECK) && defined(FANCHECK) && defined(TACH_1) && TACH_1 >-1
 	fan_measuring = false; // prevent EXTINT7 breaking into the measurement
 	unsigned long tach1max = 0;
 	uint8_t tach1cntr = 0;
@@ -3838,10 +3816,14 @@ eeprom_update_word((uint16_t*)EEPROM_NOZZLE_DIAMETER_uM,0xFFFF);
 		//  lcd_calibration();
 	  // }
 
-  }  
-  else if (code_seen('^')) {
-    // nothing, this is a version line
-  } else if(code_seen('G'))
+  } 
+  // This prevents reading files with "^" in their names.
+  // Since it is unclear, if there is some usage of this construct,
+  // it will be deprecated in 3.9 alpha a possibly completely removed in the future:
+  // else if (code_seen('^')) {
+  //  // nothing, this is a version line
+  // }
+  else if(code_seen('G'))
   {
 	gcode_in_progress = (int)code_value();
 //	printf_P(_N("BEGIN G-CODE=%u\n"), gcode_in_progress);
@@ -4389,15 +4371,15 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			if (result)
 			{
 				current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				current_position[Z_AXIS] = 50;
 				current_position[Y_AXIS] = 180;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				st_synchronize();
 				lcd_show_fullscreen_message_and_wait_P(_T(MSG_REMOVE_STEEL_SHEET));
 				current_position[Y_AXIS] = pgm_read_float(bed_ref_points_4 + 1);
 				current_position[X_AXIS] = pgm_read_float(bed_ref_points_4);
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				st_synchronize();
 				gcode_G28(false, false, true);
 
@@ -4405,7 +4387,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			if ((current_temperature_pinda > 35) && (farm_mode == false)) {
 				//waiting for PIDNA probe to cool down in case that we are not in farm mode
 				current_position[Z_AXIS] = 100;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				if (lcd_wait_for_pinda(35) == false) { //waiting for PINDA probe to cool, if this takes more then time expected, temp. cal. fails
 					lcd_temp_cal_show_result(false);
 					break;
@@ -4429,12 +4411,12 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			custom_message_state = 1;
 			lcd_setstatuspgm(_T(MSG_TEMP_CALIBRATION));
 			current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			current_position[X_AXIS] = PINDA_PREHEAT_X;
 			current_position[Y_AXIS] = PINDA_PREHEAT_Y;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			current_position[Z_AXIS] = PINDA_PREHEAT_Z;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			st_synchronize();
 
 			while (current_temperature_pinda < start_temp)
@@ -4446,10 +4428,10 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			eeprom_update_byte((uint8_t*)EEPROM_CALIBRATION_STATUS_PINDA, 0); //invalidate temp. calibration in case that in will be aborted during the calibration process 
 
 			current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			current_position[X_AXIS] = pgm_read_float(bed_ref_points_4);
 			current_position[Y_AXIS] = pgm_read_float(bed_ref_points_4 + 1);
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			st_synchronize();
 
 			bool find_z_result = find_bed_induction_sensor_point_z(-1.f);
@@ -4477,12 +4459,12 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 				setTargetBed(50 + 10 * (temp - 30) / 5);
 //				setTargetHotend(255, 0);
 				current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				current_position[X_AXIS] = PINDA_PREHEAT_X;
 				current_position[Y_AXIS] = PINDA_PREHEAT_Y;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				current_position[Z_AXIS] = PINDA_PREHEAT_Z;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				st_synchronize();
 				while (current_temperature_pinda < temp)
 				{
@@ -4490,10 +4472,10 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 					serialecho_temperatures();
 				}
 				current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				current_position[X_AXIS] = pgm_read_float(bed_ref_points_4);
 				current_position[Y_AXIS] = pgm_read_float(bed_ref_points_4 + 1);
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+				plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 				st_synchronize();
 				find_z_result = find_bed_induction_sensor_point_z(-1.f);
 				if (find_z_result == false) {
@@ -4533,7 +4515,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 		current_position[X_AXIS] = PINDA_PREHEAT_X;
 		current_position[Y_AXIS] = PINDA_PREHEAT_Y;
 		current_position[Z_AXIS] = PINDA_PREHEAT_Z;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 		st_synchronize();
 		
 		while (abs(degBed() - PINDA_MIN_T) > 1) {
@@ -4549,11 +4531,11 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 		eeprom_update_byte((uint8_t*)EEPROM_CALIBRATION_STATUS_PINDA, 0); //invalidate temp. calibration in case that in will be aborted during the calibration process 
 
 		current_position[Z_AXIS] = 5;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 
 		current_position[X_AXIS] = BED_X0;
 		current_position[Y_AXIS] = BED_Y0;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+		plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 		st_synchronize();
 		
 		find_bed_induction_sensor_point_z(-1.f);
@@ -4570,7 +4552,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			current_position[X_AXIS] = PINDA_PREHEAT_X;
 			current_position[Y_AXIS] = PINDA_PREHEAT_Y;
 			current_position[Z_AXIS] = PINDA_PREHEAT_Z;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			st_synchronize();
 			while (degBed() < t_c) {
 				delay_keep_alive(1000);
@@ -4581,10 +4563,10 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 				serialecho_temperatures();
 			}
 			current_position[Z_AXIS] = 5;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			current_position[X_AXIS] = BED_X0;
 			current_position[Y_AXIS] = BED_Y0;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			st_synchronize();
 			find_bed_induction_sensor_point_z(-1.f);
 			z_shift = (int)((current_position[Z_AXIS] - zero_z)*cs.axis_steps_per_unit[Z_AXIS]);
@@ -4725,7 +4707,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 		// Cycle through all points and probe them
 		// First move up. During this first movement, the babystepping will be reverted.
 		current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 60, active_extruder);
+		plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 60, active_extruder);
 		// The move to the first calibration point.
 		current_position[X_AXIS] = BED_X0;
 		current_position[Y_AXIS] = BED_Y0;
@@ -4740,7 +4722,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			world2machine_clamp(current_position[X_AXIS], current_position[Y_AXIS]);
 		#endif //SUPPORT_VERBOSITY
 
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[X_AXIS] / 30, active_extruder);
+		plan_buffer_line_curposXYZE(homing_feedrate[X_AXIS] / 30, active_extruder);
 		// Wait until the move is finished.
 		st_synchronize();
 
@@ -4792,7 +4774,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			if((ix == 0) && (iy == 0)) current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
 			else current_position[Z_AXIS] += 2.f / nMeasPoints; //use relative movement from Z coordinate where PINDa triggered on previous point. This makes calibration faster.
 			float init_z_bckp = current_position[Z_AXIS];
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
+			plan_buffer_line_curposXYZE(Z_LIFT_FEEDRATE, active_extruder);
 			st_synchronize();
 
 			// Move to XY position of the sensor point.
@@ -4813,7 +4795,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			#endif // SUPPORT_VERBOSITY
 
 			//printf_P(PSTR("after clamping: [%f;%f]\n"), current_position[X_AXIS], current_position[Y_AXIS]);
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], XY_AXIS_FEEDRATE, active_extruder);
+			plan_buffer_line_curposXYZE(XY_AXIS_FEEDRATE, active_extruder);
 			st_synchronize();
 
 			// Go down until endstop is hit
@@ -4825,7 +4807,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			if (init_z_bckp - current_position[Z_AXIS] < 0.1f) { //broken cable or initial Z coordinate too low. Go to MESH_HOME_Z_SEARCH and repeat last step (z-probe) again to distinguish between these two cases.
 				//printf_P(PSTR("Another attempt! Current Z position: %f\n"), current_position[Z_AXIS]);
 				current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
+				plan_buffer_line_curposXYZE(Z_LIFT_FEEDRATE, active_extruder);
 				st_synchronize();
 
 				if (!find_bed_induction_sensor_point_z((has_z && mesh_point > 0) ? z0 - Z_CALIBRATION_THRESHOLD : -10.f, nProbeRetry)) { //if we have data from z calibration max allowed difference is 1mm for each point, if we dont have data max difference is 10mm from initial point  
@@ -4880,7 +4862,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 			MYSERIAL.print(current_position[Z_AXIS], 5);
 		}
 		#endif // SUPPORT_VERBOSITY
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
+		plan_buffer_line_curposXYZE(Z_LIFT_FEEDRATE, active_extruder);
 		st_synchronize();
 		if (mesh_point != nMeasPoints * nMeasPoints) {
                Sound_MakeSound(e_SOUND_TYPE_StandardAlert);
@@ -4897,14 +4879,14 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
                     // ~ Z-homing (can not be used "G28", because X & Y-homing would have been done before (Z-homing))
                     bState=enable_z_endstop(false);
                     current_position[Z_AXIS] -= 1;
-                    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 40, active_extruder);
+                    plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 40, active_extruder);
                     st_synchronize();
                     enable_z_endstop(true);
 #ifdef TMC2130
                     tmc2130_home_enter(Z_AXIS_MASK);
 #endif // TMC2130
                     current_position[Z_AXIS] = MESH_HOME_Z_SEARCH;
-                    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 40, active_extruder);
+                    plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 40, active_extruder);
                     st_synchronize();
 #ifdef TMC2130
                     tmc2130_home_exit();
@@ -5037,7 +5019,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
 		//unretract (after PINDA preheat retraction)
 		if (degHotend(active_extruder) > EXTRUDE_MINTEMP && temp_cal_active == true && calibration_status_pinda() == true && target_temperature_bed >= 50) {
 			current_position[E_AXIS] += default_retraction;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400, active_extruder);
+			plan_buffer_line_curposXYZE(400, active_extruder);
 		}
 		KEEPALIVE_STATE(NOT_BUSY);
 		// Restore custom message state
@@ -5342,7 +5324,7 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
     // -----------------------------------
     case 23: 
       starpos = (strchr(strchr_pointer + 4,'*'));
-      if(starpos!=NULL)
+	  if(starpos!=NULL)
         *(starpos)='\0';
       card.openFile(strchr_pointer + 4,true);
       break;
@@ -5362,11 +5344,18 @@ if(eSoundMode!=e_SOUND_MODE_SILENT)
       card.pauseSDPrint();
       break;
 
-    //! ### M26 - Set SD index
+    //! ### M26 S\<index\> - Set SD index
+    //! Set position in SD card file to index in bytes.
+    //! This command is expected to be called after M23 and before M24.
+    //! Otherwise effect of this command is undefined.
     // ----------------------------------
     case 26: 
       if(card.cardOK && code_seen('S')) {
-        card.setIndex(code_value_long());
+        long index = code_value_long();
+        card.setIndex(index);
+        // We don't disable interrupt during update of sdpos_atomic
+        // as we expect, that SD card print is not active in this moment
+        sdpos_atomic = index;
       }
       break;
 
@@ -5903,7 +5892,6 @@ Sigma_Exit:
           {
               setTargetHotendSafe(code_value(), extruder);
           }
-          setWatch();
           break;
     }
 
@@ -6048,7 +6036,6 @@ Sigma_Exit:
         }
       #endif
 
-      setWatch();
       codenum = _millis();
 
       /* See if we are heating up or cooling down */
@@ -7768,7 +7755,7 @@ Sigma_Exit:
 	  	if (mmu_enabled) 
 		{
 			st_synchronize();
-			mmu_continue_loading(is_usb_printing);
+			mmu_continue_loading(is_usb_printing  || (lcd_commands_type == LcdCommands::Layer1Cal));
 			mmu_extruder = tmp_extruder; //filament change is finished
 			mmu_load_to_nozzle();
 		}
@@ -7812,7 +7799,7 @@ Sigma_Exit:
 #endif //defined(MMU_HAS_CUTTER) && defined(MMU_ALWAYS_CUT)
 				  mmu_command(MmuCmd::T0 + tmp_extruder);
 				  manage_response(true, true, MMU_TCODE_MOVE);
-		          mmu_continue_loading(is_usb_printing);
+		          mmu_continue_loading(is_usb_printing  || (lcd_commands_type == LcdCommands::Layer1Cal));
 
 				  mmu_extruder = tmp_extruder; //filament change is finished
 
@@ -9022,7 +9009,7 @@ void bed_check(float x_dimension, float y_dimension, int x_points_num, int y_poi
 	card.openFile(filename_wldsd, false);
 
 	/*destination[Z_AXIS] = mesh_home_z_search;
-	//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
+	//plan_buffer_line_curposXYZE(Z_LIFT_FEEDRATE, active_extruder);
 
 	plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
 	for(int8_t i=0; i < NUM_AXIS; i++) {
@@ -9056,7 +9043,7 @@ void bed_check(float x_dimension, float y_dimension, int x_points_num, int y_poi
 		if (iy & 1) ix = (x_points_num - 1) - ix; // Zig zag
 		float z0 = 0.f;
 		/*destination[Z_AXIS] = mesh_home_z_search;
-		//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
+		//plan_buffer_line_curposXYZE(Z_LIFT_FEEDRATE, active_extruder);
 
 		plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
 		for(int8_t i=0; i < NUM_AXIS; i++) {
@@ -9220,7 +9207,7 @@ void bed_analysis(float x_dimension, float y_dimension, int x_points_num, int y_
 	card.openFile(filename_wldsd, false);
 
 	current_position[Z_AXIS] = mesh_home_z_search;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 60, active_extruder);
 
 	int XY_AXIS_FEEDRATE = homing_feedrate[X_AXIS] / 20;
 	int Z_LIFT_FEEDRATE = homing_feedrate[Z_AXIS] / 40;
@@ -9245,14 +9232,14 @@ void bed_analysis(float x_dimension, float y_dimension, int x_points_num, int y_
 		if (iy & 1) ix = (x_points_num - 1) - ix; // Zig zag
 		float z0 = 0.f;
 		current_position[Z_AXIS] = mesh_home_z_search;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], Z_LIFT_FEEDRATE, active_extruder);
+		plan_buffer_line_curposXYZE(Z_LIFT_FEEDRATE, active_extruder);
 		st_synchronize();
 
 
 		current_position[X_AXIS] = 13.f + ix * (x_dimension / (x_points_num - 1)) - bed_zero_ref_x + shift_x;
 		current_position[Y_AXIS] = 6.4f + iy * (y_dimension / (y_points_num - 1)) - bed_zero_ref_y + shift_y;
 
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], XY_AXIS_FEEDRATE, active_extruder);
+		plan_buffer_line_curposXYZE(XY_AXIS_FEEDRATE, active_extruder);
 		st_synchronize();
 
 		if (!find_bed_induction_sensor_point_z(-10.f)) { //if we have data from z calibration max allowed difference is 1mm for each point, if we dont have data max difference is 10mm from initial point  
@@ -9366,12 +9353,12 @@ void temp_compensation_start() {
 	if (degHotend(active_extruder) > EXTRUDE_MINTEMP) {
 		current_position[E_AXIS] -= default_retraction;
 	}
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400, active_extruder);
+	plan_buffer_line_curposXYZE(400, active_extruder);
 	
 	current_position[X_AXIS] = PINDA_PREHEAT_X;
 	current_position[Y_AXIS] = PINDA_PREHEAT_Y;
 	current_position[Z_AXIS] = PINDA_PREHEAT_Z;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+	plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 	st_synchronize();
 	while (fabs(degBed() - target_temperature_bed) > 1) delay_keep_alive(1000);
 
@@ -9492,17 +9479,17 @@ void long_pause() //long pause print
 
 	//retract
 	current_position[E_AXIS] -= default_retraction;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400, active_extruder);
+	plan_buffer_line_curposXYZE(400, active_extruder);
 
 	//lift z
 	current_position[Z_AXIS] += Z_PAUSE_LIFT;
 	if (current_position[Z_AXIS] > Z_MAX_POS) current_position[Z_AXIS] = Z_MAX_POS;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 15, active_extruder);
+	plan_buffer_line_curposXYZE(15, active_extruder);
 
 	//Move XY to side
 	current_position[X_AXIS] = X_PAUSE_POS;
 	current_position[Y_AXIS] = Y_PAUSE_POS;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 50, active_extruder);
+	plan_buffer_line_curposXYZE(50, active_extruder);
 
 	// Turn off the print fan
 	fanSpeed = 0;
@@ -9520,7 +9507,7 @@ void serialecho_temperatures() {
 	SERIAL_PROTOCOL_F(degBed(), 1);
 	SERIAL_PROTOCOLLN("");
 }
-extern uint32_t sdpos_atomic;
+
 #ifdef UVLO_SUPPORT
 
 void uvlo_()
@@ -9607,7 +9594,6 @@ void uvlo_()
     st_synchronize();
 
     disable_e0();
-    disable_z();
     // Move Z up to the next 0th full step.
     // Write the file position.
     eeprom_update_dword((uint32_t*)(EEPROM_FILE_POSITION), sd_position);
@@ -9646,8 +9632,6 @@ void uvlo_()
 
     st_synchronize();
     printf_P(_N("stps%d\n"), tmc2130_rd_MSCNT(Z_AXIS));
-
-    disable_z();
     
     // Increment power failure counter
 	eeprom_update_byte((uint8_t*)EEPROM_POWER_COUNT, eeprom_read_byte((uint8_t*)EEPROM_POWER_COUNT) + 1);
@@ -9657,7 +9641,7 @@ void uvlo_()
 #if 0
     // Move the print head to the side of the print until all the power stored in the power supply capacitors is depleted.
     current_position[X_AXIS] = (current_position[X_AXIS] < 0.5f * (X_MIN_POS + X_MAX_POS)) ? X_MIN_POS : X_MAX_POS;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 500, active_extruder);
+    plan_buffer_line_curposXYZE(500, active_extruder);
     st_synchronize();
 #endif
 wdt_enable(WDTO_500MS);
@@ -9686,7 +9670,6 @@ tmc2130_set_current_r(Z_AXIS, 20);
 z_microsteps=tmc2130_rd_MSCNT(Z_TMC2130_CS);
 #endif //TMC2130
 planner_abort_hard();
-disable_z();
 
 //save current position only in case, where the printer is moving on Z axis, which is only when EEPROM_UVLO is 1
 //EEPROM_UVLO is 1 after normal uvlo or after recover_print(), when the extruder is moving on Z axis after rehome
@@ -10223,7 +10206,7 @@ void restore_print_from_ram_and_continue(float e_move)
 	else {
 		//not sd printing nor usb printing
 	}
-	printf_P(PSTR("ok\n")); //dummy response because of octoprint is waiting for this
+	SERIAL_PROTOCOLLNRPGM(MSG_OK); //dummy response because of octoprint is waiting for this
 	lcd_setstatuspgm(_T(WELCOME_MSG));
 	saved_printing = false;
 }
@@ -10294,7 +10277,7 @@ static void print_time_remaining_init()
 void load_filament_final_feed()
 {
 	current_position[E_AXIS]+= FILAMENTCHANGE_FINALFEED;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], FILAMENTCHANGE_EFEED_FINAL, active_extruder);
+	plan_buffer_line_curposXYZE(FILAMENTCHANGE_EFEED_FINAL, active_extruder);
 }
 
 //! @brief Wait for user to check the state
@@ -10424,22 +10407,22 @@ void M600_load_filament_movements()
 	do
 	{
 		current_position[E_AXIS] += 0.002;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 500, active_extruder);
+		plan_buffer_line_curposXYZE(500, active_extruder);
 		delay_keep_alive(2);
 	}
 	while (!lcd_clicked());
 	st_synchronize();
 	current_position[E_AXIS] += bowden_length[mmu_extruder];
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000, active_extruder);
+	plan_buffer_line_curposXYZE(3000, active_extruder);
 	current_position[E_AXIS] += FIL_LOAD_LENGTH - 60;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 1400, active_extruder);
+	plan_buffer_line_curposXYZE(1400, active_extruder);
 	current_position[E_AXIS] += 40;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 400, active_extruder);
+	plan_buffer_line_curposXYZE(400, active_extruder);
 	current_position[E_AXIS] += 10;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 50, active_extruder);
+	plan_buffer_line_curposXYZE(50, active_extruder);
 #else
 	current_position[E_AXIS]+= FILAMENTCHANGE_FIRSTFEED ;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], FILAMENTCHANGE_EFEED_FIRST, active_extruder); 
+	plan_buffer_line_curposXYZE(FILAMENTCHANGE_EFEED_FIRST, active_extruder); 
 #endif                
 	load_filament_final_feed();
 	lcd_loading_filament();
@@ -10534,34 +10517,20 @@ if(!(bEnableForce_z||eeprom_read_byte((uint8_t*)EEPROM_SILENT)))
 
 void disable_force_z()
 {
-uint16_t z_microsteps=0;
+    uint16_t z_microsteps=0;
 
-if(!bEnableForce_z)
-     return;                                      // motor already disabled (may be ;-p )
-bEnableForce_z=false;
+    if(!bEnableForce_z) return;   // motor already disabled (may be ;-p )
 
-// alignment to full-step
-#ifdef TMC2130
-z_microsteps=tmc2130_rd_MSCNT(Z_TMC2130_CS);
-#endif // TMC2130
-planner_abort_hard();
-sei();
-plan_buffer_line(
-     current_position[X_AXIS], 
-     current_position[Y_AXIS], 
-     current_position[Z_AXIS]+float((1024-z_microsteps+7)>>4)/cs.axis_steps_per_unit[Z_AXIS], 
-     current_position[E_AXIS],
-     40, active_extruder);
-st_synchronize();
-
-// switching to silent mode
+    bEnableForce_z=false;
+
+    // switching to silent mode
 #ifdef TMC2130
-tmc2130_mode=TMC2130_MODE_SILENT;
-update_mode_profile();
-tmc2130_init(true);
+    tmc2130_mode=TMC2130_MODE_SILENT;
+    update_mode_profile();
+    tmc2130_init(true);
 #endif // TMC2130
 
-axis_known_position[Z_AXIS]=false; 
+    axis_known_position[Z_AXIS]=false;
 }
 
 

Firmware/SdBaseFile.cpp

@@ -394,7 +394,10 @@ bool SdBaseFile::make83Name(const char* str, uint8_t* name, const char** ptr) {
       i = 8;   // place for extension
     } else {
       // illegal FAT characters
-      PGM_P p = PSTR("|<>^+=?/[];,*\"\\");
+      //PGM_P p = PSTR("|<>^+=?/[];,*\"\\");
+      // 2019-08-27 really?
+      // Microsoft defines, that only a subset of these characters is not allowed.
+      PGM_P p = PSTR("|<>?/*\"\\");
       uint8_t b;
       while ((b = pgm_read_byte(p++))) if (b == c) goto fail;
       // check size and only allow ASCII printable characters

Firmware/cmdqueue.cpp

@@ -224,9 +224,13 @@ void cmdqueue_dump_to_serial_single_line(int nr, const char *p)
     SERIAL_ECHOPGM("Entry nr: ");
     SERIAL_ECHO(nr);
     SERIAL_ECHOPGM(", type: ");
-    SERIAL_ECHO(int(*p));
+    int type = *p;
+    SERIAL_ECHO(type);
+    SERIAL_ECHOPGM(", size: ");
+    unsigned int size = *(unsigned int*)(p + 1);
+    SERIAL_ECHO(size);
     SERIAL_ECHOPGM(", cmd: ");
-    SERIAL_ECHO(p+1);  
+    SERIAL_ECHO(p + CMDHDRSIZE);
     SERIAL_ECHOLNPGM("");
 }
 
@@ -247,7 +251,7 @@ void cmdqueue_dump_to_serial()
             for (const char *p = cmdbuffer + bufindr; p < cmdbuffer + bufindw; ++ nr) {
                 cmdqueue_dump_to_serial_single_line(nr, p);
                 // Skip the command.
-                for (++p; *p != 0; ++ p);
+                for (p += CMDHDRSIZE; *p != 0; ++ p);
                 // Skip the gaps.
                 for (++p; p < cmdbuffer + bufindw && *p == 0; ++ p);
             }
@@ -255,14 +259,14 @@ void cmdqueue_dump_to_serial()
             for (const char *p = cmdbuffer + bufindr; p < cmdbuffer + sizeof(cmdbuffer); ++ nr) {
                 cmdqueue_dump_to_serial_single_line(nr, p);
                 // Skip the command.
-                for (++p; *p != 0; ++ p);
+                for (p += CMDHDRSIZE; *p != 0; ++ p);
                 // Skip the gaps.
                 for (++p; p < cmdbuffer + sizeof(cmdbuffer) && *p == 0; ++ p);
             }
             for (const char *p = cmdbuffer; p < cmdbuffer + bufindw; ++ nr) {
                 cmdqueue_dump_to_serial_single_line(nr, p);
                 // Skip the command.
-                for (++p; *p != 0; ++ p);
+                for (p += CMDHDRSIZE; *p != 0; ++ p);
                 // Skip the gaps.
                 for (++p; p < cmdbuffer + bufindw && *p == 0; ++ p);
             }

Firmware/cmdqueue.h

@@ -45,6 +45,8 @@ extern bool cmdbuffer_front_already_processed;
 // Debugging information will be sent to serial line.
 //#define CMDBUFFER_DEBUG
 
+extern uint32_t sdpos_atomic;
+
 extern int serial_count;
 extern boolean comment_mode;
 extern char *strchr_pointer;

Firmware/config.h

@@ -49,7 +49,7 @@
 //#define LANG_MODE              0 // primary language only
 #define LANG_MODE              1 // sec. language support
 
-#define LANG_SIZE_RESERVED     0x2800 // reserved space for secondary language (10240 bytes)
+#define LANG_SIZE_RESERVED     0x3000 // reserved space for secondary language (12288 bytes)
 
 
 #endif //_CONFIG_H

Firmware/eeprom.cpp

@@ -41,7 +41,8 @@ bool eeprom_is_uninitialized<char>(char *address)
     return (0xff == eeprom_read_byte(reinterpret_cast<uint8_t*>(address)));
 }
 
-bool is_sheet_initialized(uint8_t sheet_num){
+bool eeprom_is_sheet_initialized(uint8_t sheet_num)
+{
   return (0xffff != eeprom_read_word(reinterpret_cast<uint16_t*>(&(EEPROM_Sheets_base->
   s[sheet_num].z_offset))));
 }
@@ -61,7 +62,14 @@ void eeprom_init()
     if (eeprom_read_word((uint16_t*)EEPROM_MMU_LOAD_FAIL_TOT) == 0xffff) eeprom_update_word((uint16_t *)EEPROM_MMU_LOAD_FAIL_TOT, 0);
     if (eeprom_read_byte((uint8_t*)EEPROM_MMU_FAIL) == 0xff) eeprom_update_byte((uint8_t *)EEPROM_MMU_FAIL, 0);
     if (eeprom_read_byte((uint8_t*)EEPROM_MMU_LOAD_FAIL) == 0xff) eeprom_update_byte((uint8_t *)EEPROM_MMU_LOAD_FAIL, 0);
-    if (eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)) == 0xff) eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), 0);
+    if (eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)) == 0xff)
+    {
+        eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), 0);
+        // When upgrading from version older version (before multiple sheets were implemented in v3.8.0)
+        // Sheet 1 uses the previous Live adjust Z (@EEPROM_BABYSTEP_Z)
+        int last_babystep = eeprom_read_word((uint16_t *)EEPROM_BABYSTEP_Z);
+        eeprom_update_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->s[0].z_offset)), last_babystep);
+    }
     
     for (uint_least8_t i = 0; i < (sizeof(Sheets::s)/sizeof(Sheets::s[0])); ++i)
     {
@@ -72,24 +80,108 @@ void eeprom_init()
         }
         if(is_uninitialized)
         {
+            SheetName sheetName;
+            eeprom_default_sheet_name(i,sheetName);
 
-            char sheet_PROGMEM_buffer[8];
-            strcpy_P(sheet_PROGMEM_buffer, (char *)pgm_read_word(&(defaultSheetNames[i])));
             for (uint_least8_t a = 0; a < sizeof(Sheet::name); ++a){
-                eeprom_write(&(EEPROM_Sheets_base->s[i].name[a]), sheet_PROGMEM_buffer[a]);
-            }
-          
-            // When upgrading from version older version (before multiple sheets were implemented in v3.8.0)
-	    // Sheet 1 uses the previous Live adjust Z (@EEPROM_BABYSTEP_Z)
-            if(i == 0){
-                int last_babystep = eeprom_read_word((uint16_t *)EEPROM_BABYSTEP_Z);
-                eeprom_write_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->s[i].z_offset)), last_babystep);
+                eeprom_write(&(EEPROM_Sheets_base->s[i].name[a]), sheetName.c[a]);
             }
         }
     }
+    if(!eeprom_is_sheet_initialized(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet))))
+    {
+        eeprom_switch_to_next_sheet();
+    }
     check_babystep();
 }
 
+//! @brief Get default sheet name for index
+//!
+//! | index | sheetName |
+//! | ----- | --------- |
+//! | 0     | Smooth1   |
+//! | 1     | Smooth2   |
+//! | 2     | Textur1   |
+//! | 3     | Textur2   |
+//! | 4     | Custom1   |
+//! | 5     | Custom2   |
+//! | 6     | Custom3   |
+//! | 7     | Custom4   |
+//!
+//! @param[in] index
+//! @param[out] sheetName
+void eeprom_default_sheet_name(uint8_t index, SheetName &sheetName)
+{
+    static_assert(8 == sizeof(SheetName),"Default sheet name needs to be adjusted.");
 
+    if (index < 2)
+    {
+        strcpy_P(sheetName.c, PSTR("Smooth"));
+    }
+    else if (index < 4)
+    {
+        strcpy_P(sheetName.c, PSTR("Textur"));
+    }
+    else
+    {
+        strcpy_P(sheetName.c, PSTR("Custom"));
+    }
 
+    switch (index)
+    {
+    case 0:
+        sheetName.c[6] = '1';
+        break;
+    case 1:
+        sheetName.c[6] = '2';
+        break;
+    case 2:
+        sheetName.c[6] = '1';
+        break;
+    case 3:
+        sheetName.c[6] = '2';
+        break;
+    case 4:
+        sheetName.c[6] = '1';
+        break;
+    case 5:
+        sheetName.c[6] = '2';
+        break;
+    case 6:
+        sheetName.c[6] = '3';
+        break;
+    case 7:
+        sheetName.c[6] = '4';
+        break;
+    default:
+        break;
+    }
+
+    sheetName.c[7] = '\0';
+}
+
+//! @brief Get next initialized sheet
+//!
+//! If current sheet is the only sheet initialized, current sheet is returned.
+//!
+//! @param sheet Current sheet
+//! @return next initialized sheet
+//! @retval -1 no sheet is initialized
+int8_t eeprom_next_initialized_sheet(int8_t sheet)
+{
+    for (int8_t i = 0; i < static_cast<int8_t>(sizeof(Sheets::s)/sizeof(Sheet)); ++i)
+    {
+        ++sheet;
+        if (sheet >= static_cast<int8_t>(sizeof(Sheets::s)/sizeof(Sheet))) sheet = 0;
+        if (eeprom_is_sheet_initialized(sheet)) return sheet;
+    }
+    return -1;
+}
 
+void eeprom_switch_to_next_sheet()
+{
+    int8_t sheet = eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet));
+
+    sheet = eeprom_next_initialized_sheet(sheet);
+    if (sheet >= 0) eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), sheet);
+}

Firmware/eeprom.h

@@ -3,12 +3,6 @@
 
 #include <stdint.h>
 
-#ifdef __cplusplus
-void eeprom_init();
-extern bool is_sheet_initialized(uint8_t sheet_num);
-#endif
-
-
 typedef struct
 {
     char name[7];     //!< Can be null terminated, doesn't need to be null terminated
@@ -19,12 +13,12 @@ typedef struct
 
 typedef struct
 {
-    Sheet s[3];
+    Sheet s[8];
     uint8_t active_sheet;
 } Sheets;
 // sizeof(Sheets). Do not change it unless EEPROM_Sheets_base is last item in EEPROM.
 // Otherwise it would move following items.
-#define EEPROM_SHEETS_SIZEOF 34
+#define EEPROM_SHEETS_SIZEOF 89
 
 #ifdef __cplusplus
 static_assert(sizeof(Sheets) == EEPROM_SHEETS_SIZEOF, "Sizeof(Sheets) is not EEPROM_SHEETS_SIZEOF.");
@@ -36,9 +30,9 @@ static_assert(sizeof(Sheets) == EEPROM_SHEETS_SIZEOF, "Sizeof(Sheets) is not EEP
 #define EEPROM_TOP 4096
 #define EEPROM_SILENT 4095
 #define EEPROM_LANG 4094
-#define EEPROM_BABYSTEP_X 4092
-#define EEPROM_BABYSTEP_Y 4090
-#define EEPROM_BABYSTEP_Z 4088
+#define EEPROM_BABYSTEP_X 4092 //unused
+#define EEPROM_BABYSTEP_Y 4090 //unused
+#define EEPROM_BABYSTEP_Z 4088 //legacy, multiple values stored now in EEPROM_Sheets_base
 #define EEPROM_CALIBRATION_STATUS 4087
 #define EEPROM_BABYSTEP_Z0 4085
 #define EEPROM_FILAMENTUSED 4081
@@ -235,5 +229,16 @@ enum
     EEPROM_MMU_CUTTER_ENABLED_always = 2,
 };
 
+#ifdef __cplusplus
+void eeprom_init();
+bool eeprom_is_sheet_initialized(uint8_t sheet_num);
+struct SheetName
+{
+    char c[sizeof(Sheet::name) + 1];
+};
+void eeprom_default_sheet_name(uint8_t index, SheetName &sheetName);
+int8_t eeprom_next_initialized_sheet(int8_t sheet);
+void eeprom_switch_to_next_sheet();
+#endif
 
 #endif // EEPROM_H

Firmware/first_lay_cal.cpp

@@ -40,15 +40,26 @@ void lay1cal_preheat()
 
 }
 
-//! @brief Print intro line
+//! @brief Load filament
 //! @param cmd_buffer character buffer needed to format gcodes
 //! @param filament filament to use (applies for MMU only)
-void lay1cal_intro_line(char *cmd_buffer, uint8_t filament)
+void lay1cal_load_filament(char *cmd_buffer, uint8_t filament)
+{
+    if (mmu_enabled)
+    {
+        enquecommand_P(PSTR("M83"));
+        enquecommand_P(PSTR("G1 Y-3.0 F1000.0"));
+        enquecommand_P(PSTR("G1 Z0.4 F1000.0"));
+        sprintf_P(cmd_buffer, PSTR("T%d"), filament);
+        enquecommand(cmd_buffer);
+    }
+
+}
+
+//! @brief Print intro line
+void lay1cal_intro_line()
 {
-    static const char cmd_intro_mmu_0[] PROGMEM = "M83";
-    static const char cmd_intro_mmu_1[] PROGMEM = "G1 Y-3.0 F1000.0";
-    static const char cmd_intro_mmu_2[] PROGMEM = "G1 Z0.4 F1000.0";
-    static const char cmd_intro_mmu_3[] PROGMEM = "G1 X55.0 E32.0 F1073.0"; // call T code before
+    static const char cmd_intro_mmu_3[] PROGMEM = "G1 X55.0 E32.0 F1073.0";
     static const char cmd_intro_mmu_4[] PROGMEM = "G1 X5.0 E32.0 F1800.0";
     static const char cmd_intro_mmu_5[] PROGMEM = "G1 X55.0 E8.0 F2000.0";
     static const char cmd_intro_mmu_6[] PROGMEM = "G1 Z0.3 F1000.0";
@@ -61,10 +72,7 @@ void lay1cal_intro_line(char *cmd_buffer, uint8_t filament)
 
     static const char * const intro_mmu_cmd[] PROGMEM =
     {
-        cmd_intro_mmu_0,
-        cmd_intro_mmu_1,
-        cmd_intro_mmu_2,
-        cmd_intro_mmu_3, // call T code before
+        cmd_intro_mmu_3,
         cmd_intro_mmu_4,
         cmd_intro_mmu_5,
         cmd_intro_mmu_6,
@@ -80,11 +88,6 @@ void lay1cal_intro_line(char *cmd_buffer, uint8_t filament)
     {
         for (uint8_t i = 0; i < (sizeof(intro_mmu_cmd)/sizeof(intro_mmu_cmd[0])); ++i)
         {
-            if (3 == i)
-                {
-                    sprintf_P(cmd_buffer, PSTR("T%d"), filament);
-                    enquecommand(cmd_buffer);
-                }
             enquecommand_P(static_cast<char*>(pgm_read_ptr(&intro_mmu_cmd[i])));
         }
     }

Firmware/first_lay_cal.h

@@ -7,7 +7,8 @@
 #include <stdint.h>
 
 void lay1cal_preheat();
-void lay1cal_intro_line(char *cmd_buffer, uint8_t filament);
+void lay1cal_load_filament(char *cmd_buffer, uint8_t filament);
+void lay1cal_intro_line();
 void lay1cal_before_meander();
 void lay1cal_meander(char *cmd_buffer);
 void lay1cal_square(char *cmd_buffer, uint8_t i);

Firmware/heatbed_pwm.cpp

@@ -19,91 +19,162 @@
 // So the automaton runs atop of inner 8 (or 16) cycles.
 // The finite automaton is running in the ISR(TIMER0_OVF_vect)
 
+// 2019-08-14 update: the original algorithm worked very well, however there were 2 regressions:
+// 1. 62kHz ISR requires considerable amount of processing power, 
+//    USB transfer speed dropped by 20%, which was most notable when doing short G-code segments.
+// 2. Some users reported TLed PSU started clicking when running at 120V/60Hz. 
+//    This looks like the original algorithm didn't maintain base PWM 30Hz, but only 15Hz
+// To address both issues, there is an improved approach based on the idea of leveraging
+// different CLK prescalers in some automaton states - i.e. when holding LOW or HIGH on the output pin,
+// we don't have to clock 62kHz, but we can increase the CLK prescaler for these states to 8 (or even 64).
+// That shall result in the ISR not being called that much resulting in regained performance
+// Theoretically this is relatively easy, however one must be very carefull handling the AVR's timer
+// control registers correctly, especially setting them in a correct order.
+// Some registers are double buffered, some changes are applied in next cycles etc.
+// The biggest problem was with the CLK prescaler itself - this circuit is shared among almost all timers,
+// we don't want to reset the prescaler counted value when transiting among automaton states.
+// Resetting the prescaler would make the PWM more precise, right now there are temporal segments
+// of variable period ranging from 0 to 7 62kHz ticks - that's logical, the timer must "sync"
+// to the new slower CLK after setting the slower prescaler value.
+// In our application, this isn't any significant problem and may be ignored.
+// Doing changes in timer's registers non-correctly results in artefacts on the output pin
+// - it can toggle unnoticed, which will result in bed clicking again.
+// That's why there are special transition states ZERO_TO_RISE and ONE_TO_FALL, which enable the
+// counter change its operation atomically and without artefacts on the output pin.
+// The resulting signal on the output pin was checked with an osciloscope. 
+// If there are any change requirements in the future, the signal must be checked with an osciloscope again,
+// ad-hoc changes may completely screw things up!
+
 ///! Definition off finite automaton states
 enum class States : uint8_t {
-  ZERO = 0,
-  RISE = 1,
-  ONE = 2,
-  FALL = 3
-};
-
-///! State table for the inner part of the finite automaton
-///! Basically it specifies what shall happen if the outer automaton is requesting setting the heat pin to 0 (OFF) or 1 (ON)
-///! ZERO: steady 0 (OFF), no change for the whole period
-///! RISE: 8 (16) fast PWM cycles with increasing duty up to steady ON
-///! ONE:  steady 1 (ON), no change for the whole period 
-///! FALL: 8 (16) fast PWM cycles with decreasing duty down to steady OFF
-///! @@TODO move it into progmem
-static States stateTable[4*2] = {
-// off             on
-States::ZERO,      States::RISE, // ZERO
-States::FALL,      States::ONE,  // RISE
-States::FALL,      States::ONE,  // ONE
-States::ZERO,      States::RISE  // FALL
+	ZERO_START = 0,///< entry point of the automaton - reads the soft_pwm_bed value for the next whole PWM cycle
+	ZERO,          ///< steady 0 (OFF), no change for the whole period
+	ZERO_TO_RISE,  ///< metastate allowing the timer change its state atomically without artefacts on the output pin
+	RISE,          ///< 16 fast PWM cycles with increasing duty up to steady ON
+	RISE_TO_ONE,   ///< metastate allowing the timer change its state atomically without artefacts on the output pin
+	ONE,           ///< steady 1 (ON), no change for the whole period 
+	ONE_TO_FALL,   ///< metastate allowing the timer change its state atomically without artefacts on the output pin
+	FALL,          ///< 16 fast PWM cycles with decreasing duty down to steady OFF
+	FALL_TO_ZERO   ///< metastate allowing the timer change its state atomically without artefacts on the output pin
 };
 
 ///! Inner states of the finite automaton
-static States state = States::ZERO;
+static States state = States::ZERO_START;
 
-///! Inner and outer PWM counters
-static uint8_t outer = 0;
-static uint8_t inner = 0;
+///! Fast PWM counter is used in the RISE and FALL states (62.5kHz)
+static uint8_t slowCounter = 0;
+///! Slow PWM counter is used in the ZERO and ONE states (62.5kHz/8 or 64)
+static uint8_t fastCounter = 0;
+///! PWM counter for the whole cycle - a cache for soft_pwm_bed
 static uint8_t pwm = 0;
 
-///! the slow PWM duty for the next 30Hz cycle
+///! The slow PWM duty for the next 30Hz cycle
 ///! Set in the whole firmware at various places
 extern unsigned char soft_pwm_bed;
 
-/// Fine tuning of automaton cycles
-#if 1
-static const uint8_t innerMax = 16;
-static const uint8_t innerShift = 4;
-#else
-static const uint8_t innerMax = 8;
-static const uint8_t innerShift = 5;
-#endif
+/// fastMax - how many fast PWM steps to do in RISE and FALL states
+/// 16 is a good compromise between silenced bed ("smooth" edges)
+/// and not burning the switching MOSFET
+static const uint8_t fastMax = 16;
+
+/// Scaler 16->256 for fast PWM
+static const uint8_t fastShift = 4;
+
+/// Increment slow PWM counter by slowInc every ZERO or ONE state
+/// This allows for fine-tuning the basic PWM switching frequency
+/// A possible further optimization - use a 64 prescaler (instead of 8)
+/// increment slowCounter by 1
+/// but use less bits of soft PWM - something like soft_pwm_bed >> 2
+/// that may further reduce the CPU cycles required by the bed heating automaton
+/// Due to the nature of bed heating the reduced PID precision may not be a major issue, however doing 8x less ISR(timer0_ovf) may significantly improve the performance 
+static const uint8_t slowInc = 1;
 
 ISR(TIMER0_OVF_vect)          // timer compare interrupt service routine
 {
-  if( inner ){
-    switch(state){
-    case States::ZERO:
-      OCR0B = 255;
-	  // Commenting the following code saves 6B, but it is left here for reference
-	  // It is not necessary to set it all over again, because we can only get into the ZERO state from the FALL state (which sets this register)
-//       TCCR0A |= (1 << COM0B1) | (1 << COM0B0);
-      break;
-    case States::RISE:
-      OCR0B = (innerMax - inner) << innerShift;
-//       TCCR0A |= (1 << COM0B1); // this bit is always 1
-      TCCR0A &= ~(1 << COM0B0);
-      break;  
-    case States::ONE:
-      OCR0B = 255;
-	  // again - may be skipped, because we get into the ONE state only from RISE (which sets this register)
-//       TCCR0A |= (1 << COM0B1);
-       TCCR0A &= ~(1 << COM0B0);
-      break;
-    case States::FALL:
-      OCR0B = (innerMax - inner) << innerShift; // this is the same as in RISE, because now we are setting the zero part of duty due to inverting mode
-      // must switch to inverting mode already here, because it takes a whole PWM cycle and it would make a "1" at the end of this pwm cycle
-	  TCCR0A |= /*(1 << COM0B1) |*/ (1 << COM0B0); 
-      break;
-    }
-    --inner;
-  } else {
-    if( ! outer ){ // at the end of 30Hz PWM period
-      // synchro is not needed (almost), soft_pwm_bed is just 1 byte, 1-byte write instruction is atomic
-      pwm = soft_pwm_bed << 1;
-    }
-	if( pwm > outer || pwm >= 254 ){
-      // soft_pwm_bed has a range of 0-127, that why a <<1 is done here. That also means that we may get only up to 254 which we want to be full-time 1 (ON)
-      state = stateTable[ uint8_t(state) * 2 + 1 ];
-    } else {
-      // switch OFF
-      state = stateTable[ uint8_t(state) * 2 + 0 ];
+	switch(state){
+	case States::ZERO_START:
+		pwm = soft_pwm_bed << 1;// expecting soft_pwm_bed to be 7bit!
+		if( pwm != 0 ){
+			state = States::ZERO;     // do nothing, let it tick once again after the 30Hz period
+		}
+		break;
+	case States::ZERO: // end of state ZERO - we'll either stay in ZERO or change to RISE
+		// In any case update our cache of pwm value for the next whole cycle from soft_pwm_bed
+		slowCounter += slowInc; // this does software timer_clk/256 or less (depends on slowInc)
+		if( slowCounter > pwm ){
+			return;
+		} // otherwise moving towards RISE
+		state = States::ZERO_TO_RISE; // and finalize the change in a transitional state RISE0
+		break;
+	// even though it may look like the ZERO state may be glued together with the ZERO_TO_RISE, don't do it
+	// the timer must tick once more in order to get rid of occasional output pin toggles.
+	case States::ZERO_TO_RISE:  // special state for handling transition between prescalers and switching inverted->non-inverted fast-PWM without toggling the output pin.
+		// It must be done in consequent steps, otherwise the pin will get flipped up and down during one PWM cycle.
+		// Also beware of the correct sequence of the following timer control registers initialization - it really matters!
+		state = States::RISE;     // prepare for standard RISE cycles
+		fastCounter = fastMax - 1;// we'll do 16-1 cycles of RISE
+		TCNT0 = 255;              // force overflow on the next clock cycle
+		TCCR0B = (1 << CS00);     // change prescaler to 1, i.e. 62.5kHz
+		TCCR0A &= ~(1 << COM0B0); // Clear OC0B on Compare Match, set OC0B at BOTTOM (non-inverting mode)
+		break;
+	case States::RISE:
+		OCR0B = (fastMax - fastCounter) << fastShift;
+		if( fastCounter ){
+			--fastCounter;
+		} else { // end of RISE cycles, changing into state ONE
+			state = States::RISE_TO_ONE;
+			OCR0B = 255;          // full duty
+			TCNT0 = 254;          // make the timer overflow in the next cycle
+			// @@TODO these constants are still subject to investigation
+		}
+		break;
+	case States::RISE_TO_ONE:
+		state = States::ONE;
+		OCR0B = 255;              // full duty
+		TCNT0 = 255;              // make the timer overflow in the next cycle
+		TCCR0B = (1 << CS01);     // change prescaler to 8, i.e. 7.8kHz
+		break;
+	case States::ONE:             // state ONE - we'll either stay in ONE or change to FALL
+		OCR0B = 255;
+		slowCounter += slowInc;   // this does software timer_clk/256 or less
+		if( slowCounter < pwm ){
+			return;
+		}
+		if( (soft_pwm_bed << 1) >= (255 - slowInc - 1) ){  //@@TODO simplify & explain
+			// if slowInc==2, soft_pwm == 251 will be the first to do short drops to zero. 252 will keep full heating
+			return;           // want full duty for the next ONE cycle again - so keep on heating and just wait for the next timer ovf
+		}
+		// otherwise moving towards FALL
+		// @@TODO it looks like ONE_TO_FALL isn't necessary, there are no artefacts at all
+		state = States::ONE;//_TO_FALL;
+//		TCCR0B = (1 << CS00);      // change prescaler to 1, i.e. 62.5kHz
+//		break;
+//	case States::ONE_TO_FALL:
+//		OCR0B = 255;              // zero duty
+		state=States::FALL;
+		fastCounter = fastMax - 1;// we'll do 16-1 cycles of RISE
+		TCNT0 = 255;              // force overflow on the next clock cycle
+		TCCR0B = (1 << CS00);     // change prescaler to 1, i.e. 62.5kHz
+		// must switch to inverting mode already here, because it takes a whole PWM cycle and it would make a "1" at the end of this pwm cycle
+		// COM0B1 remains set both in inverting and non-inverting mode
+		TCCR0A |= (1 << COM0B0);  // inverting mode
+		break;
+	case States::FALL:
+		OCR0B = (fastMax - fastCounter) << fastShift; // this is the same as in RISE, because now we are setting the zero part of duty due to inverting mode
+		//TCCR0A |= (1 << COM0B0); // already set in ONE_TO_FALL
+		if( fastCounter ){
+			--fastCounter;
+		} else {   // end of FALL cycles, changing into state ZERO
+			state = States::FALL_TO_ZERO;
+			TCNT0 = 128; //@@TODO again - need to wait long enough to propagate the timer state changes
+			OCR0B = 255;
+		}
+		break;
+	case States::FALL_TO_ZERO:
+		state = States::ZERO_START; // go to read new soft_pwm_bed value for the next cycle
+		TCNT0 = 128;
+		OCR0B = 255;
+		TCCR0B = (1 << CS01); // change prescaler to 8, i.e. 7.8kHz
+		break;		
     }
-    ++outer;
-    inner = innerMax;
-  }
 }

Firmware/lcd.cpp

@@ -189,9 +189,10 @@ static void lcd_begin(uint8_t clear)
 	#endif
 }
 
-static void lcd_putchar(char c, FILE *)
+static int lcd_putchar(char c, FILE *)
 {
 	lcd_write(c);
+	return 0;
 }
 
 void lcd_init(void)

Firmware/lcd.h

@@ -11,7 +11,6 @@
 extern FILE _lcdout;
 
 #define lcdout (&_lcdout)
-extern void lcd_putchar(char c, FILE *stream);
 
 extern void lcd_init(void);
 

Firmware/menu.cpp

@@ -203,9 +203,13 @@ void menu_format_sheet_E(const Sheet &sheet_E, SheetFormatBuffer &buffer)
 void menu_format_sheet_select_E(const Sheet &sheet_E, SheetFormatBuffer &buffer)
 {
     uint_least8_t index = sprintf_P(buffer.c,PSTR("%-9.9S["), _T(MSG_SHEET));
-    eeprom_read_block(&(buffer.c[index]), sheet_E.name, 7);
-	buffer.c[index + 7] = ']';
-    buffer.c[index + 8] = '\0';
+    eeprom_read_block(&(buffer.c[index]), sheet_E.name, sizeof(sheet_E.name)/sizeof(sheet_E.name[0]));
+    for (const uint_least8_t start = index; static_cast<uint_least8_t>(index - start) < sizeof(sheet_E.name)/sizeof(sheet_E.name[0]); ++index)
+    {
+        if (buffer.c[index] == '\0') break;
+    }
+	buffer.c[index] = ']';
+    buffer.c[index + 1] = '\0';
 }
 
 static void menu_draw_item_select_sheet_E(char type_char, const Sheet &sheet)
@@ -290,14 +294,18 @@ uint8_t menu_item_submenu_E(const Sheet &sheet, menu_func_t submenu)
     return 0;
 }
 
-uint8_t menu_item_submenu_select_sheet_E(const Sheet &sheet, menu_func_t submenu)
+uint8_t menu_item_function_E(const Sheet &sheet, menu_func_t func)
 {
     if (menu_item == menu_line)
     {
-        if (lcd_draw_update) menu_draw_item_select_sheet_E(LCD_STR_ARROW_RIGHT[0], sheet);
+        if (lcd_draw_update) menu_draw_item_select_sheet_E(' ', sheet);
         if (menu_clicked && (lcd_encoder == menu_item))
         {
-            menu_submenu(submenu);
+            menu_clicked = false;
+            lcd_consume_click();
+            lcd_update_enabled = 0;
+            if (func) func();
+            lcd_update_enabled = 1;
             return menu_item_ret();
         }
     }

Firmware/menu.h

@@ -103,8 +103,8 @@ extern uint8_t menu_item_submenu_P(const char* str, menu_func_t submenu);
 #define MENU_ITEM_SUBMENU_E(sheet, submenu) do { if (menu_item_submenu_E(sheet, submenu)) return; } while (0)
 extern uint8_t menu_item_submenu_E(const Sheet &sheet, menu_func_t submenu);
 
-#define MENU_ITEM_SUBMENU_SELECT_SHEET_E(sheet, submenu) do { if (menu_item_submenu_select_sheet_E(sheet, submenu)) return; } while (0)
-extern uint8_t menu_item_submenu_select_sheet_E(const Sheet &sheet, menu_func_t submenu);
+#define MENU_ITEM_FUNCTION_E(sheet, submenu) do { if (menu_item_function_E(sheet, submenu)) return; } while (0)
+extern uint8_t menu_item_function_E(const Sheet &sheet, menu_func_t func);
 
 #define MENU_ITEM_BACK_P(str) do { if (menu_item_back_P(str)) return; } while (0)
 extern uint8_t menu_item_back_P(const char* str);

Firmware/mesh_bed_calibration.cpp

@@ -919,7 +919,7 @@ static inline void go_xy(float x, float y, float fr)
 
 static inline void go_to_current(float fr)
 {
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], fr, active_extruder);
+    plan_buffer_line_curposXYZE(fr, active_extruder);
     st_synchronize();
 }
 
@@ -2769,7 +2769,7 @@ bool sample_z() {
 	//make space
 	current_position[Z_AXIS] += 150;
 	go_to_current(homing_feedrate[Z_AXIS] / 60);
-	//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate, active_extruder););
+	//plan_buffer_line_curposXYZE(feedrate, active_extruder););
 
 	lcd_show_fullscreen_message_and_wait_P(_T(MSG_PLACE_STEEL_SHEET));
 

Firmware/mmu.cpp

@@ -537,7 +537,7 @@ void mmu_command(MmuCmd cmd)
 void mmu_load_step(bool synchronize)
 {
 		current_position[E_AXIS] = current_position[E_AXIS] + MMU_LOAD_FEEDRATE * 0.1;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+		plan_buffer_line_curposXYZE(MMU_LOAD_FEEDRATE, active_extruder);
 		if (synchronize) st_synchronize();
 }
 
@@ -602,7 +602,7 @@ bool mmu_get_response(uint8_t move)
 				    {
                         printf_P(PSTR("Unload 1\n"));
                         current_position[E_AXIS] = current_position[E_AXIS] - MMU_LOAD_FEEDRATE * MMU_LOAD_TIME_MS*0.001;
-                        plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+                        plan_buffer_line_curposXYZE(MMU_LOAD_FEEDRATE, active_extruder);
                         st_synchronize();
 				    }
 				}
@@ -620,7 +620,7 @@ bool mmu_get_response(uint8_t move)
                     {
                         printf_P(PSTR("Unload 2\n"));
                         current_position[E_AXIS] = current_position[E_AXIS] - MMU_LOAD_FEEDRATE * MMU_LOAD_TIME_MS*0.001;
-                        plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+                        plan_buffer_line_curposXYZE(MMU_LOAD_FEEDRATE, active_extruder);
                         st_synchronize();
                     }
 				}
@@ -698,13 +698,13 @@ void manage_response(bool move_axes, bool turn_off_nozzle, uint8_t move)
 					  //lift z
 					  current_position[Z_AXIS] += Z_PAUSE_LIFT;
 					  if (current_position[Z_AXIS] > Z_MAX_POS) current_position[Z_AXIS] = Z_MAX_POS;
-					  plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 15, active_extruder);
+					  plan_buffer_line_curposXYZE(15, active_extruder);
 					  st_synchronize();
 					  					  
 					  //Move XY to side
 					  current_position[X_AXIS] = X_PAUSE_POS;
 					  current_position[Y_AXIS] = Y_PAUSE_POS;
-					  plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 50, active_extruder);
+					  plan_buffer_line_curposXYZE(50, active_extruder);
 					  st_synchronize();
 				  }
 				  if (turn_off_nozzle) {
@@ -762,10 +762,10 @@ void manage_response(bool move_axes, bool turn_off_nozzle, uint8_t move)
 				  lcd_display_message_fullscreen_P(_i("MMU OK. Resuming position..."));
 				  current_position[X_AXIS] = x_position_bckp;
 				  current_position[Y_AXIS] = y_position_bckp;
-				  plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 50, active_extruder);
+				  plan_buffer_line_curposXYZE(50, active_extruder);
 				  st_synchronize();
 				  current_position[Z_AXIS] = z_position_bckp;
-				  plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 15, active_extruder);
+				  plan_buffer_line_curposXYZE(15, active_extruder);
 				  st_synchronize();
 			  }
 			  else {
@@ -804,19 +804,19 @@ void mmu_load_to_nozzle()
 		current_position[E_AXIS] += 7.2f;
 	}
     float feedrate = 562;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate / 60, active_extruder);
+	plan_buffer_line_curposXYZE(feedrate / 60, active_extruder);
     st_synchronize();
 	current_position[E_AXIS] += 14.4f;
 	feedrate = 871;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate / 60, active_extruder);
+	plan_buffer_line_curposXYZE(feedrate / 60, active_extruder);
     st_synchronize();
 	current_position[E_AXIS] += 36.0f;
 	feedrate = 1393;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate / 60, active_extruder);
+	plan_buffer_line_curposXYZE(feedrate / 60, active_extruder);
     st_synchronize();
 	current_position[E_AXIS] += 14.4f;
 	feedrate = 871;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate / 60, active_extruder);
+	plan_buffer_line_curposXYZE(feedrate / 60, active_extruder);
     st_synchronize();
 	if (!saved_e_relative_mode) axis_relative_modes[E_AXIS] = false;
 }
@@ -889,7 +889,7 @@ void mmu_M600_load_filament(bool automatic, float nozzle_temp)
     mmu_command(MmuCmd::T0 + tmp_extruder);
 
     manage_response(false, true, MMU_LOAD_MOVE);
-    mmu_continue_loading(is_usb_printing);
+    mmu_continue_loading(is_usb_printing || (lcd_commands_type == LcdCommands::Layer1Cal));
     mmu_extruder = tmp_extruder; //filament change is finished
 
     mmu_load_to_nozzle();
@@ -903,7 +903,7 @@ void extr_mov(float shift, float feed_rate)
 { //move extruder no matter what the current heater temperature is
 	set_extrude_min_temp(.0);
 	current_position[E_AXIS] += shift;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feed_rate, active_extruder);
+	plan_buffer_line_curposXYZE(feed_rate, active_extruder);
 	set_extrude_min_temp(EXTRUDE_MINTEMP);
 }
 #endif //SNMM
@@ -1069,8 +1069,7 @@ void mmu_filament_ramming()
     for(uint8_t i = 0; i < (sizeof(ramming_sequence)/sizeof(E_step));++i)
     {
         current_position[E_AXIS] += pgm_read_float(&(ramming_sequence[i].extrude));
-        plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-                current_position[E_AXIS], pgm_read_float(&(ramming_sequence[i].feed_rate)), active_extruder);
+        plan_buffer_line_curposXYZE(pgm_read_float(&(ramming_sequence[i].feed_rate)), active_extruder);
         st_synchronize();
     }
 }
@@ -1140,39 +1139,39 @@ void extr_unload()
 		lcd_set_cursor(0, 2); lcd_puts_P(_T(MSG_PLEASE_WAIT));
 		if (current_position[Z_AXIS] < 15) {
 			current_position[Z_AXIS] += 15; //lifting in Z direction to make space for extrusion
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 25, active_extruder);
+			plan_buffer_line_curposXYZE(25, active_extruder);
 		}
 		
 		current_position[E_AXIS] += 10; //extrusion
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 10, active_extruder);
+		plan_buffer_line_curposXYZE(10, active_extruder);
 		st_current_set(2, E_MOTOR_HIGH_CURRENT);
 		if (current_temperature[0] < 230) { //PLA & all other filaments
 			current_position[E_AXIS] += 5.4;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2800 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(2800 / 60, active_extruder);
 			current_position[E_AXIS] += 3.2;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			current_position[E_AXIS] += 3;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3400 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3400 / 60, active_extruder);
 		}
 		else { //ABS
 			current_position[E_AXIS] += 3.1;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(2000 / 60, active_extruder);
 			current_position[E_AXIS] += 3.1;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 2500 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(2500 / 60, active_extruder);
 			current_position[E_AXIS] += 4;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 3000 / 60, active_extruder);
+			plan_buffer_line_curposXYZE(3000 / 60, active_extruder);
 			/*current_position[X_AXIS] += 23; //delay
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder); //delay
+			plan_buffer_line_curposXYZE(600 / 60, active_extruder); //delay
 			current_position[X_AXIS] -= 23; //delay
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 600 / 60, active_extruder); //delay*/
+			plan_buffer_line_curposXYZE(600 / 60, active_extruder); //delay*/
 			delay_keep_alive(4700);
 		}
 	
 		max_feedrate[E_AXIS] = 80;
 		current_position[E_AXIS] -= (bowden_length[mmu_extruder] + 60 + FIL_LOAD_LENGTH) / 2;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 500, active_extruder);
+		plan_buffer_line_curposXYZE(500, active_extruder);
 		current_position[E_AXIS] -= (bowden_length[mmu_extruder] + 60 + FIL_LOAD_LENGTH) / 2;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 500, active_extruder);
+		plan_buffer_line_curposXYZE(500, active_extruder);
 		st_synchronize();
 		//st_current_init();
 		if (SilentMode != SILENT_MODE_OFF) st_current_set(2, tmp_motor[2]); //set back to normal operation currents
@@ -1465,11 +1464,9 @@ bFilamentAction=false;                            // NOT in "mmu_fil_eject_menu(
 static bool can_load()
 {
     current_position[E_AXIS] += 60;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-            current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+    plan_buffer_line_curposXYZE(MMU_LOAD_FEEDRATE, active_extruder);
     current_position[E_AXIS] -= 52;
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-            current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+    plan_buffer_line_curposXYZE(MMU_LOAD_FEEDRATE, active_extruder);
     st_synchronize();
 
     uint_least8_t filament_detected_count = 0;
@@ -1479,8 +1476,7 @@ static bool can_load()
     for(uint_least8_t i = 0; i < steps; ++i)
     {
         current_position[E_AXIS] -= e_increment;
-        plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
-                current_position[E_AXIS], MMU_LOAD_FEEDRATE, active_extruder);
+        plan_buffer_line_curposXYZE(MMU_LOAD_FEEDRATE, active_extruder);
         st_synchronize();
         if(0 == PIN_GET(IR_SENSOR_PIN))
         {
@@ -1601,13 +1597,13 @@ void mmu_continue_loading(bool blocking)
             //lift z
             current_position[Z_AXIS] += Z_PAUSE_LIFT;
             if (current_position[Z_AXIS] > Z_MAX_POS) current_position[Z_AXIS] = Z_MAX_POS;
-            plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 15, active_extruder);
+            plan_buffer_line_curposXYZE(15, active_extruder);
             st_synchronize();
 
             //Move XY to side
             current_position[X_AXIS] = X_PAUSE_POS;
             current_position[Y_AXIS] = Y_PAUSE_POS;
-            plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 50, active_extruder);
+            plan_buffer_line_curposXYZE(50, active_extruder);
             st_synchronize();
 
             mmu_command(MmuCmd::U0);

Firmware/planner.cpp

@@ -651,11 +651,15 @@ void planner_abort_hard()
     waiting_inside_plan_buffer_line_print_aborted = true;
 }
 
+void plan_buffer_line_curposXYZE(float feed_rate, uint8_t extruder) { 
+	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feed_rate, extruder );
+}
+
 float junction_deviation = 0.1;
 // Add a new linear movement to the buffer. steps_x, _y and _z is the absolute position in 
 // mm. Microseconds specify how many microseconds the move should take to perform. To aid acceleration
 // calculation the caller must also provide the physical length of the line in millimeters.
-void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, const uint8_t &extruder)
+void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, uint8_t extruder)
 {
     // Calculate the buffer head after we push this byte
   int next_buffer_head = next_block_index(block_buffer_head);

Firmware/planner.h

@@ -140,7 +140,14 @@ void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate
 // Get the position applying the bed level matrix if enabled
 vector_3 plan_get_position();
 #else
-void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, const uint8_t &extruder);
+
+/// Extracting common call of 
+/// plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], ...
+/// saves almost 5KB.
+/// The performance penalty is negligible, since these planned lines are usually maintenance moves with the extruder.
+void plan_buffer_line_curposXYZE(float feed_rate, uint8_t extruder);
+
+void plan_buffer_line(float x, float y, float z, const float &e, float feed_rate, uint8_t extruder);
 //void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate, const uint8_t &extruder);
 #endif // ENABLE_AUTO_BED_LEVELING
 

Firmware/sound.h

@@ -3,10 +3,10 @@
 #define SOUND_H
 
 
-#define MSG_SOUND_MODE_LOUD "Sound      [loud]"
-#define MSG_SOUND_MODE_ONCE "Sound      [once]"
+#define MSG_SOUND_MODE_LOUD   "Sound      [loud]"
+#define MSG_SOUND_MODE_ONCE   "Sound      [once]"
 #define MSG_SOUND_MODE_SILENT "Sound    [silent]"
-#define MSG_SOUND_MODE_BLIND "Sound     [blind]" 
+#define MSG_SOUND_MODE_BLIND  "Sound    [assist]" 
 
 
 #define e_SOUND_MODE_NULL 0xFF

Firmware/stepper.cpp

@@ -1562,7 +1562,8 @@ void EEPROM_read_st(int pos, uint8_t* value, uint8_t size)
 
 void st_current_init() //Initialize Digipot Motor Current
 {  
-uint8_t SilentMode = eeprom_read_byte((uint8_t*)EEPROM_SILENT);
+  uint8_t SilentMode = eeprom_read_byte((uint8_t*)EEPROM_SILENT);
+  if (SilentMode == 0xff) SilentMode = 0; //set power to High Power (MK2.5) or Normal Power (MK3, unused)
   SilentModeMenu = SilentMode;
   #ifdef MOTOR_CURRENT_PWM_XY_PIN
     pinMode(MOTOR_CURRENT_PWM_XY_PIN, OUTPUT);

Firmware/temperature.cpp

@@ -73,10 +73,6 @@ int current_voltage_raw_bed = 0;
 
 int current_temperature_bed_raw = 0;
 float current_temperature_bed = 0.0;
-#ifdef TEMP_SENSOR_1_AS_REDUNDANT
-  int redundant_temperature_raw = 0;
-  float redundant_temperature = 0.0;
-#endif
   
 
 #ifdef PIDTEMP
@@ -175,13 +171,8 @@ static int bed_minttemp_raw = HEATER_BED_RAW_LO_TEMP;
 static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP;
 #endif
 
-#ifdef TEMP_SENSOR_1_AS_REDUNDANT
-  static void *heater_ttbl_map[2] = {(void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE };
-  static uint8_t heater_ttbllen_map[2] = { HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN };
-#else
-  static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE );
-  static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN );
-#endif
+static void *heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( (void *)HEATER_0_TEMPTABLE, (void *)HEATER_1_TEMPTABLE, (void *)HEATER_2_TEMPTABLE );
+static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS( HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN );
 
 static float analog2temp(int raw, uint8_t e);
 static float analog2tempBed(int raw);
@@ -195,11 +186,6 @@ enum TempRunawayStates
 	TempRunaway_ACTIVE = 2,
 };
 
-#ifdef WATCH_TEMP_PERIOD
-int watch_start_temp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0);
-unsigned long watchmillis[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0);
-#endif //WATCH_TEMP_PERIOD
-
 #ifndef SOFT_PWM_SCALE
 #define SOFT_PWM_SCALE 0
 #endif
@@ -728,34 +714,6 @@ void manage_heater()
     {
       soft_pwm[e] = 0;
     }
-
-    #ifdef WATCH_TEMP_PERIOD
-    if(watchmillis[e] && _millis() - watchmillis[e] > WATCH_TEMP_PERIOD)
-    {
-        if(degHotend(e) < watch_start_temp[e] + WATCH_TEMP_INCREASE)
-        {
-            setTargetHotend(0, e);
-            LCD_MESSAGEPGM("Heating failed");
-            SERIAL_ECHO_START;
-            SERIAL_ECHOLN("Heating failed");
-        }else{
-            watchmillis[e] = 0;
-        }
-    }
-    #endif
-    #ifdef TEMP_SENSOR_1_AS_REDUNDANT
-      if(fabs(current_temperature[0] - redundant_temperature) > MAX_REDUNDANT_TEMP_SENSOR_DIFF) {
-        disable_heater();
-        if(IsStopped() == false) {
-          SERIAL_ERROR_START;
-          SERIAL_ERRORLNPGM("Extruder switched off. Temperature difference between temp sensors is too high !");
-          LCD_ALERTMESSAGEPGM("Err: REDUNDANT TEMP ERROR");
-        }
-        #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
-          Stop();
-        #endif
-      }
-    #endif
   } // End extruder for loop
 
 #define FAN_CHECK_PERIOD 5000 //5s
@@ -907,11 +865,7 @@ void manage_heater()
 // Derived from RepRap FiveD extruder::getTemperature()
 // For hot end temperature measurement.
 static float analog2temp(int raw, uint8_t e) {
-#ifdef TEMP_SENSOR_1_AS_REDUNDANT
-  if(e > EXTRUDERS)
-#else
   if(e >= EXTRUDERS)
-#endif
   {
       SERIAL_ERROR_START;
       SERIAL_ERROR((int)e);
@@ -1054,10 +1008,6 @@ static void updateTemperaturesFromRawValues()
 	current_temperature_bed = analog2tempBed(current_temperature_bed_raw);
 #endif //DEBUG_HEATER_BED_SIM
 
-    #ifdef TEMP_SENSOR_1_AS_REDUNDANT
-      redundant_temperature = analog2temp(redundant_temperature_raw, 1);
-    #endif
-
     CRITICAL_SECTION_START;
     temp_meas_ready = false;
     CRITICAL_SECTION_END;
@@ -1221,20 +1171,6 @@ void tp_init()
 #endif //BED_MAXTEMP
 }
 
-void setWatch() 
-{  
-#ifdef WATCH_TEMP_PERIOD
-  for (int e = 0; e < EXTRUDERS; e++)
-  {
-    if(degHotend(e) < degTargetHotend(e) - (WATCH_TEMP_INCREASE * 2))
-    {
-      watch_start_temp[e] = degHotend(e);
-      watchmillis[e] = _millis();
-    } 
-  }
-#endif 
-}
-
 #if (defined (TEMP_RUNAWAY_BED_HYSTERESIS) && TEMP_RUNAWAY_BED_TIMEOUT > 0) || (defined (TEMP_RUNAWAY_EXTRUDER_HYSTERESIS) && TEMP_RUNAWAY_EXTRUDER_TIMEOUT > 0)
 void temp_runaway_check(int _heater_id, float _target_temperature, float _current_temperature, float _output, bool _isbed)
 {

Firmware/temperature.h

@@ -74,9 +74,6 @@ extern int current_voltage_raw_pwr;
 extern int current_voltage_raw_bed;
 #endif
 
-#ifdef TEMP_SENSOR_1_AS_REDUNDANT
-  extern float redundant_temperature;
-#endif
 
 #if defined(CONTROLLERFAN_PIN) && CONTROLLERFAN_PIN > -1
   extern unsigned char soft_pwm_bed;
@@ -220,7 +217,6 @@ FORCE_INLINE bool isCoolingBed() {
 
 int getHeaterPower(int heater);
 void disable_heater();
-void setWatch();
 void updatePID();
 
 

Firmware/timer02.c

@@ -26,7 +26,7 @@ void timer0_init(void)
 	OCR0B = 255;
 	// Set fast PWM mode and inverting mode.
 	TCCR0A = (1 << WGM01) | (1 << WGM00) | (1 << COM0B1) | (1 << COM0B0);  
-	TCCR0B = (1 << CS00);    // no clock prescaling
+	TCCR0B = (1 << CS01);    // CLK/8 prescaling
 	TIMSK0 |= (1 << TOIE0);  // enable timer overflow interrupt
 	
 	// Everything, that used to be on timer0 was moved to timer2 (delay, beeping, millis etc.)

Firmware/ultralcd.cpp

@@ -61,17 +61,9 @@ uint8_t SilentModeMenu_MMU = 1; //activate mmu unit stealth mode
 
 int8_t FSensorStateMenu = 1;
 
-int8_t CrashDetectMenu = 1;
-
-
 extern bool fsensor_enable();
 extern void fsensor_disable();
 
-#ifdef TMC2130
-extern void crashdet_enable();
-extern void crashdet_disable();
-#endif //TMC2130
-
 
 #ifdef SDCARD_SORT_ALPHA
 bool presort_flag = false;
@@ -255,10 +247,6 @@ void lcd_finishstatus();
 static void lcd_sdcard_menu();
 static void lcd_sheet_menu();
 
-static void lcd_select_sheet_0_menu();
-static void lcd_select_sheet_1_menu();
-static void lcd_select_sheet_2_menu();
-
 #ifdef DELTA_CALIBRATION_MENU
 static void lcd_delta_calibrate_menu();
 #endif // DELTA_CALIBRATION_MENU
@@ -1362,42 +1350,46 @@ void lcd_commands()
 
 		if(lcd_commands_step>1) lcd_timeoutToStatus.start(); //if user dont confirm live adjust Z value by pressing the knob, we are saving last value by timeout to status screen
 
-        if (!blocks_queued() && cmd_buffer_empty())
+        if (!blocks_queued() && cmd_buffer_empty() && !saved_printing)
         {
             switch(lcd_commands_step)
             {
             case 0:
-                lcd_commands_step = 10;
+                lcd_commands_step = 11;
                 break;
             case 20:
                 filament = 0;
-                lcd_commands_step = 10;
+                lcd_commands_step = 11;
                 break;
             case 21:
                 filament = 1;
-                lcd_commands_step = 10;
+                lcd_commands_step = 11;
                 break;
             case 22:
                 filament = 2;
-                lcd_commands_step = 10;
+                lcd_commands_step = 11;
                 break;
             case 23:
                 filament = 3;
-                lcd_commands_step = 10;
+                lcd_commands_step = 11;
                 break;
             case 24:
                 filament = 4;
+                lcd_commands_step = 11;
+                break;
+            case 11:
+                lay1cal_preheat();
                 lcd_commands_step = 10;
                 break;
             case 10:
-                lay1cal_preheat();
+                lay1cal_load_filament(cmd1, filament);
                 lcd_commands_step = 9;
                 break;
             case 9:
                 lcd_clear();
                 menu_depth = 0;
                 menu_submenu(lcd_babystep_z);
-                lay1cal_intro_line(cmd1, filament);
+                lay1cal_intro_line();
                 lcd_commands_step = 8;
                 break;
             case 8:
@@ -1677,100 +1669,12 @@ static void lcd_move_menu_axis();
 
 /* Menu implementation */
 
-static void lcd_preheat_farm()
-{
-  setTargetHotend0(FARM_PREHEAT_HOTEND_TEMP);
-  setTargetBed(FARM_PREHEAT_HPB_TEMP);
-  fanSpeed = 0;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-}
-
-static void lcd_preheat_farm_nozzle()
-{
-	setTargetHotend0(FARM_PREHEAT_HOTEND_TEMP);
-	setTargetBed(0);
-	fanSpeed = 0;
-	lcd_return_to_status();
-	setWatch(); // heater sanity check timer
-}
-
-static void lcd_preheat_pla()
-{
-  setTargetHotend0(PLA_PREHEAT_HOTEND_TEMP);
-  if (!wizard_active) setTargetBed(PLA_PREHEAT_HPB_TEMP);
-  fanSpeed = PLA_PREHEAT_FAN_SPEED;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-  if (wizard_active) lcd_wizard(WizState::Unload);
-}
-
-static void lcd_preheat_asa()
-{
-  setTargetHotend0(ASA_PREHEAT_HOTEND_TEMP);
-  if (!wizard_active) setTargetBed(ASA_PREHEAT_HPB_TEMP);
-  fanSpeed = ASA_PREHEAT_FAN_SPEED;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-  if (wizard_active) lcd_wizard(WizState::Unload);
-}
-
-static void lcd_preheat_abs()
-{
-  setTargetHotend0(ABS_PREHEAT_HOTEND_TEMP);
-  if (!wizard_active) setTargetBed(ABS_PREHEAT_HPB_TEMP);
-  fanSpeed = ABS_PREHEAT_FAN_SPEED;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-  if (wizard_active) lcd_wizard(WizState::Unload);
-}
-
-static void lcd_preheat_pp()
-{
-  setTargetHotend0(PP_PREHEAT_HOTEND_TEMP);
-  if (!wizard_active) setTargetBed(PP_PREHEAT_HPB_TEMP);
-  fanSpeed = PP_PREHEAT_FAN_SPEED;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-  if (wizard_active) lcd_wizard(WizState::Unload);
-}
-
-static void lcd_preheat_pet()
-{
-  setTargetHotend0(PET_PREHEAT_HOTEND_TEMP);
-  if (!wizard_active) setTargetBed(PET_PREHEAT_HPB_TEMP);
-  fanSpeed = PET_PREHEAT_FAN_SPEED;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-  if (wizard_active) lcd_wizard(WizState::Unload);
-}
-
-static void lcd_preheat_hips()
-{
-  setTargetHotend0(HIPS_PREHEAT_HOTEND_TEMP);
-  if (!wizard_active) setTargetBed(HIPS_PREHEAT_HPB_TEMP);
-  fanSpeed = HIPS_PREHEAT_FAN_SPEED;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-  if (wizard_active) lcd_wizard(WizState::Unload);
-}
-
-static void lcd_preheat_flex()
-{
-  setTargetHotend0(FLEX_PREHEAT_HOTEND_TEMP);
-  if (!wizard_active) setTargetBed(FLEX_PREHEAT_HPB_TEMP);
-  fanSpeed = FLEX_PREHEAT_FAN_SPEED;
-  lcd_return_to_status();
-  setWatch(); // heater sanity check timer
-  if (wizard_active) lcd_wizard(WizState::Unload);
-}
-
-
 static void lcd_cooldown()
 {
   setAllTargetHotends(0);
   setTargetBed(0);
   fanSpeed = 0;
+  eFilamentAction = FilamentAction::None;
   lcd_return_to_status();
 }
 
@@ -2127,27 +2031,8 @@ static void lcd_menu_test_restore()
 //! @brief Show Preheat Menu
 static void lcd_preheat_menu()
 {
-  MENU_BEGIN();
-
-  if (!wizard_active) MENU_ITEM_BACK_P(_T(MSG_MAIN));
-
-  if (farm_mode) {
-	  MENU_ITEM_FUNCTION_P(PSTR("farm   -  " STRINGIFY(FARM_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(FARM_PREHEAT_HPB_TEMP)), lcd_preheat_farm);
-	  MENU_ITEM_FUNCTION_P(PSTR("nozzle -  " STRINGIFY(FARM_PREHEAT_HOTEND_TEMP) "/0"), lcd_preheat_farm_nozzle);
-	  MENU_ITEM_FUNCTION_P(_T(MSG_COOLDOWN), lcd_cooldown);
-  } else {
-	  MENU_ITEM_FUNCTION_P(PSTR("PLA  -  " STRINGIFY(PLA_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PLA_PREHEAT_HPB_TEMP)), lcd_preheat_pla);
-	  MENU_ITEM_FUNCTION_P(PSTR("PET  -  " STRINGIFY(PET_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PET_PREHEAT_HPB_TEMP)), lcd_preheat_pet);
-	  MENU_ITEM_FUNCTION_P(PSTR("ASA  -  " STRINGIFY(ASA_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(ASA_PREHEAT_HPB_TEMP)), lcd_preheat_asa);
-	  MENU_ITEM_FUNCTION_P(PSTR("ABS  -  " STRINGIFY(ABS_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(ABS_PREHEAT_HPB_TEMP)), lcd_preheat_abs);
-	  MENU_ITEM_FUNCTION_P(PSTR("HIPS -  " STRINGIFY(HIPS_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(HIPS_PREHEAT_HPB_TEMP)), lcd_preheat_hips);
-	  MENU_ITEM_FUNCTION_P(PSTR("PP   -  " STRINGIFY(PP_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PP_PREHEAT_HPB_TEMP)), lcd_preheat_pp);
-	  MENU_ITEM_FUNCTION_P(PSTR("FLEX -  " STRINGIFY(FLEX_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(FLEX_PREHEAT_HPB_TEMP)), lcd_preheat_flex);
-	  if (!wizard_active) MENU_ITEM_FUNCTION_P(_T(MSG_COOLDOWN), lcd_cooldown);
-  }
-  
-
-  MENU_END();
+    eFilamentAction = FilamentAction::Preheat;
+    mFilamentMenu();
 }
 
 //! @brief Show Support Menu
@@ -2372,7 +2257,7 @@ FilamentAction eFilamentAction=FilamentAction::None; // must be initialized as '
 bool bFilamentFirstRun;
 bool bFilamentPreheatState;
 bool bFilamentAction=false;
-bool bFilamentWaitingFlag=false;
+static bool bFilamentWaitingFlag=false;
 
 static void mFilamentPrompt()
 {
@@ -2397,6 +2282,7 @@ switch(eFilamentAction)
      case FilamentAction::MmuEject:
      case FilamentAction::MmuCut:
      case FilamentAction::None:
+     case FilamentAction::Preheat:
           break;
      }
 if(lcd_clicked())
@@ -2425,284 +2311,221 @@ if(lcd_clicked())
           case FilamentAction::MmuEject:
           case FilamentAction::MmuCut:
           case FilamentAction::None:
+          case FilamentAction::Preheat:
                break;
           }
      }
 }
 
-/*
-void _mFilamentItem(uint16_t nTemp,uint16_t nTempBed)
+void mFilamentItem(uint16_t nTemp, uint16_t nTempBed)
 {
-static int nTargetOld,nTargetBedOld;
-uint8_t nLevel;
-static bool bBeep=false;
-
-//if(bPreheatState)                                 // not necessary
-     nTargetOld=target_temperature[0];
-     nTargetBedOld=target_temperature_bed;
-setTargetHotend0((float)nTemp);
-setTargetBed((float)nTempBed);
-lcd_timeoutToStatus.stop();
-lcd_set_cursor(0,0);
-lcdui_print_temp(LCD_STR_THERMOMETER[0],(int)degHotend(0),(int)degTargetHotend(0));
-lcd_set_cursor(0,1);
-switch(eFilamentAction)
-     {
-     case eFILAMENT_ACTION::load:
-     case eFILAMENT_ACTION::autoLoad:
-     case eFILAMENT_ACTION::mmuLoad:
-          lcd_puts_P(_i("Preheating to load"));   ////MSG_ c=20 r=1
-          break;
-     case eFILAMENT_ACTION::unLoad:
-     case eFILAMENT_ACTION::mmuUnLoad:
-          lcd_puts_P(_i("Preheating to unload")); ////MSG_ c=20 r=1
-          break;
-     case eFILAMENT_ACTION::mmuEject:
-          lcd_puts_P(_i("Preheating to eject"));  ////MSG_ c=20 r=1
-          break;
-     case eFILAMENT_ACTION::mmuCut:
-          lcd_puts_P(_i("Preheating to cut"));  ////MSG_ c=20 r=1
-          break;
-     }
-lcd_set_cursor(0,3);
-lcd_puts_P(_i(">Cancel"));                        ////MSG_ c=20 r=1
-if(lcd_clicked())
-     {
-     if(!bFilamentPreheatState)
-          {
-          setTargetHotend0(0.0);
-          setTargetBed(0.0);
-          menu_back();
-          }
-     else {
-          setTargetHotend0((float)nTargetOld);
-          setTargetBed((float)nTargetBedOld);
-          }
-     menu_back();
-     if(eFilamentAction==eFILAMENT_ACTION::autoLoad)
-          eFilamentAction=eFILAMENT_ACTION::none; // i.e. non-autoLoad
-     }
-else {
-     if(current_temperature[0]>(target_temperature[0]*0.95))
-          {
-          switch(eFilamentAction)
-               {
-               case eFILAMENT_ACTION::load:
-               case eFILAMENT_ACTION::autoLoad:
-               case eFILAMENT_ACTION::unLoad:
-                    menu_submenu(mFilamentPrompt);
-                    break;
-               case eFILAMENT_ACTION::mmuLoad:
-                    nLevel=1;
-                    if(!bFilamentPreheatState)
-                         nLevel++;
-                    bFilamentAction=true;
-                    menu_back(nLevel);
-                    menu_submenu(mmu_load_to_nozzle_menu);
-                    break;
-               case eFILAMENT_ACTION::mmuUnLoad:
-                    nLevel=1;
-                    if(!bFilamentPreheatState)
-                         nLevel++;
-                    bFilamentAction=true;
-                    menu_back(nLevel);
-                    extr_unload();
-                    break;
-               case eFILAMENT_ACTION::mmuEject:
-                    nLevel=1;
-                    if(!bFilamentPreheatState)
-                         nLevel++;
-                    bFilamentAction=true;
-                    menu_back(nLevel);
-                    menu_submenu(mmu_fil_eject_menu);
-                    break;
-               case eFILAMENT_ACTION::mmuCut:
-                    nLevel=1;
-                    if(!bFilamentPreheatState)
-                         nLevel++;
-                    bFilamentAction=true;
-                    menu_back(nLevel);
-                    menu_submenu(mmu_cut_filament_menu);
-                    break;
-               }
-          if(bBeep)
-               Sound_MakeSound(e_SOUND_TYPE_StandardPrompt);
-          bBeep=false;
-          }
-     else bBeep=true;
-     }
-}
-*/
+    static int nTargetOld;
+    static int nTargetBedOld;
+    uint8_t nLevel;
 
-void mFilamentItem(uint16_t nTemp,uint16_t nTempBed)
-{
-static int nTargetOld,nTargetBedOld;
-uint8_t nLevel;
+    nTargetOld = target_temperature[0];
+    nTargetBedOld = target_temperature_bed;
+    setTargetHotend0((float )nTemp);
+    if (!wizard_active) setTargetBed((float) nTempBed);
 
-//if(bPreheatState)                                 // not necessary
-     nTargetOld=target_temperature[0];
-     nTargetBedOld=target_temperature_bed;
-setTargetHotend0((float)nTemp);
-setTargetBed((float)nTempBed);
-lcd_timeoutToStatus.stop();
-if(current_temperature[0]>(target_temperature[0]*0.95))
-     {
-     switch(eFilamentAction)
-          {
-          case FilamentAction::Load:
-          case FilamentAction::AutoLoad:
-          case FilamentAction::UnLoad:
-               if(bFilamentWaitingFlag)
-                    menu_submenu(mFilamentPrompt);
-               else {
-                    nLevel=bFilamentPreheatState?1:2;
-                    menu_back(nLevel);
-                    if((eFilamentAction==FilamentAction::Load)||(eFilamentAction==FilamentAction::AutoLoad))
-                         {
-                         loading_flag=true;
-                         enquecommand_P(PSTR("M701")); // load filament
-                         if(eFilamentAction==FilamentAction::AutoLoad)
-                              eFilamentAction=FilamentAction::None; // i.e. non-autoLoad
-                         }
-                    if(eFilamentAction==FilamentAction::UnLoad)
-                         enquecommand_P(PSTR("M702")); // unload filament
-                    }
-               break;
-          case FilamentAction::MmuLoad:
-               nLevel=bFilamentPreheatState?1:2;
-               bFilamentAction=true;
-               menu_back(nLevel);
-               menu_submenu(mmu_load_to_nozzle_menu);
-               break;
-          case FilamentAction::MmuUnLoad:
-               nLevel=bFilamentPreheatState?1:2;
-               bFilamentAction=true;
-               menu_back(nLevel);
-               extr_unload();
-               break;
-          case FilamentAction::MmuEject:
-               nLevel=bFilamentPreheatState?1:2;
-               bFilamentAction=true;
-               menu_back(nLevel);
-               menu_submenu(mmu_fil_eject_menu);
-               break;
-          case FilamentAction::MmuCut:
+    if (eFilamentAction == FilamentAction::Preheat)
+    {
+        eFilamentAction = FilamentAction::None;
+        lcd_return_to_status();
+        if (wizard_active) lcd_wizard(WizState::Unload);
+        return;
+    }
+
+    lcd_timeoutToStatus.stop();
+
+    if (current_temperature[0] > (target_temperature[0] * 0.95))
+    {
+        switch (eFilamentAction)
+        {
+        case FilamentAction::Load:
+        case FilamentAction::AutoLoad:
+        case FilamentAction::UnLoad:
+            if (bFilamentWaitingFlag) menu_submenu(mFilamentPrompt);
+            else
+            {
+                nLevel = bFilamentPreheatState ? 1 : 2;
+                menu_back(nLevel);
+                if ((eFilamentAction == FilamentAction::Load) || (eFilamentAction == FilamentAction::AutoLoad))
+                {
+                    loading_flag = true;
+                    enquecommand_P(PSTR("M701")); // load filament
+                    if (eFilamentAction == FilamentAction::AutoLoad) eFilamentAction = FilamentAction::None; // i.e. non-autoLoad
+                }
+                if (eFilamentAction == FilamentAction::UnLoad)
+                enquecommand_P(PSTR("M702")); // unload filament
+            }
+            break;
+        case FilamentAction::MmuLoad:
+            nLevel = bFilamentPreheatState ? 1 : 2;
+            bFilamentAction = true;
+            menu_back(nLevel);
+            menu_submenu(mmu_load_to_nozzle_menu);
+            break;
+        case FilamentAction::MmuUnLoad:
+            nLevel = bFilamentPreheatState ? 1 : 2;
+            bFilamentAction = true;
+            menu_back(nLevel);
+            extr_unload();
+            break;
+        case FilamentAction::MmuEject:
+            nLevel = bFilamentPreheatState ? 1 : 2;
+            bFilamentAction = true;
+            menu_back(nLevel);
+            menu_submenu(mmu_fil_eject_menu);
+            break;
+        case FilamentAction::MmuCut:
 #ifdef MMU_HAS_CUTTER
-               nLevel=bFilamentPreheatState?1:2;
-               bFilamentAction=true;
-               menu_back(nLevel);
-               menu_submenu(mmu_cut_filament_menu);
+            nLevel=bFilamentPreheatState?1:2;
+            bFilamentAction=true;
+            menu_back(nLevel);
+            menu_submenu(mmu_cut_filament_menu);
 #endif //MMU_HAS_CUTTER
-               break;
-          case FilamentAction::None:
-               break;
-          }
-     if(bFilamentWaitingFlag)
-          Sound_MakeSound(e_SOUND_TYPE_StandardPrompt);
-     bFilamentWaitingFlag=false;
-     }
-else {
-     bFilamentWaitingFlag=true;
-     lcd_set_cursor(0,0);
-     lcdui_print_temp(LCD_STR_THERMOMETER[0],(int)degHotend(0),(int)degTargetHotend(0));
-     lcd_set_cursor(0,1);
-     switch(eFilamentAction)
-          {
-          case FilamentAction::Load:
-          case FilamentAction::AutoLoad:
-          case FilamentAction::MmuLoad:
-               lcd_puts_P(_i("Preheating to load")); ////MSG_ c=20 r=1
-               break;
-          case FilamentAction::UnLoad:
-          case FilamentAction::MmuUnLoad:
-               lcd_puts_P(_i("Preheating to unload")); ////MSG_ c=20 r=1
-               break;
-          case FilamentAction::MmuEject:
-               lcd_puts_P(_i("Preheating to eject")); ////MSG_ c=20 r=1
-               break;
-          case FilamentAction::MmuCut:
-               lcd_puts_P(_i("Preheating to cut")); ////MSG_ c=20 r=1
-               break;
-          case FilamentAction::None:
-               break;
-          }
-     lcd_set_cursor(0,3);
-     lcd_puts_P(_i(">Cancel"));                   ////MSG_ c=20 r=1
-     if(lcd_clicked())
-          {
-          bFilamentWaitingFlag=false;
-          if(!bFilamentPreheatState)
-               {
-               setTargetHotend0(0.0);
-               setTargetBed(0.0);
-               menu_back();
-               }
-          else {
-               setTargetHotend0((float)nTargetOld);
-               setTargetBed((float)nTargetBedOld);
-               }
-          menu_back();
-          if(eFilamentAction==FilamentAction::AutoLoad)
-               eFilamentAction=FilamentAction::None; // i.e. non-autoLoad
-          }
-     }
+            break;
+        case FilamentAction::None:
+        case FilamentAction::Preheat:
+            break;
+        }
+        if (bFilamentWaitingFlag) Sound_MakeSound(e_SOUND_TYPE_StandardPrompt);
+        bFilamentWaitingFlag = false;
+    }
+    else
+    {
+        bFilamentWaitingFlag = true;
+        lcd_set_cursor(0, 0);
+        lcdui_print_temp(LCD_STR_THERMOMETER[0], (int) degHotend(0), (int) degTargetHotend(0));
+        lcd_set_cursor(0, 1);
+        switch (eFilamentAction)
+        {
+        case FilamentAction::Load:
+        case FilamentAction::AutoLoad:
+        case FilamentAction::MmuLoad:
+            lcd_puts_P(_i("Preheating to load")); ////MSG_ c=20 r=1
+            break;
+        case FilamentAction::UnLoad:
+        case FilamentAction::MmuUnLoad:
+            lcd_puts_P(_i("Preheating to unload")); ////MSG_ c=20 r=1
+            break;
+        case FilamentAction::MmuEject:
+            lcd_puts_P(_i("Preheating to eject")); ////MSG_ c=20 r=1
+            break;
+        case FilamentAction::MmuCut:
+            lcd_puts_P(_i("Preheating to cut")); ////MSG_ c=20 r=1
+            break;
+        case FilamentAction::None:
+        case FilamentAction::Preheat:
+            break;
+        }
+        lcd_set_cursor(0, 3);
+        lcd_puts_P(_i(">Cancel"));                   ////MSG_ c=20 r=1
+        if (lcd_clicked())
+        {
+            bFilamentWaitingFlag = false;
+            if (!bFilamentPreheatState)
+            {
+                setTargetHotend0(0.0);
+                setTargetBed(0.0);
+                menu_back();
+            }
+            else
+            {
+                setTargetHotend0((float )nTargetOld);
+                setTargetBed((float) nTargetBedOld);
+            }
+            menu_back();
+            if (eFilamentAction == FilamentAction::AutoLoad) eFilamentAction = FilamentAction::None; // i.e. non-autoLoad
+        }
+    }
+}
+
+static void mFilamentItem_farm()
+{
+    bFilamentPreheatState = false;
+    mFilamentItem(FARM_PREHEAT_HOTEND_TEMP, FARM_PREHEAT_HPB_TEMP);
+}
+static void mFilamentItem_farm_nozzle()
+{
+    bFilamentPreheatState = false;
+    mFilamentItem(FARM_PREHEAT_HOTEND_TEMP, 0);
 }
 
 static void mFilamentItem_PLA()
 {
-bFilamentPreheatState=false;
-mFilamentItem(PLA_PREHEAT_HOTEND_TEMP,PLA_PREHEAT_HPB_TEMP);
+    bFilamentPreheatState = false;
+    mFilamentItem(PLA_PREHEAT_HOTEND_TEMP, PLA_PREHEAT_HPB_TEMP);
 }
 
 static void mFilamentItem_PET()
 {
-bFilamentPreheatState=false;
-mFilamentItem(PET_PREHEAT_HOTEND_TEMP,PET_PREHEAT_HPB_TEMP);
+    bFilamentPreheatState = false;
+    mFilamentItem(PET_PREHEAT_HOTEND_TEMP, PET_PREHEAT_HPB_TEMP);
+}
+
+static void mFilamentItem_ASA()
+{
+    bFilamentPreheatState = false;
+    mFilamentItem(ASA_PREHEAT_HOTEND_TEMP, ASA_PREHEAT_HPB_TEMP);
 }
 
 static void mFilamentItem_ABS()
 {
-bFilamentPreheatState=false;
-mFilamentItem(ABS_PREHEAT_HOTEND_TEMP,ABS_PREHEAT_HPB_TEMP);
+    bFilamentPreheatState = false;
+    mFilamentItem(ABS_PREHEAT_HOTEND_TEMP, ABS_PREHEAT_HPB_TEMP);
 }
 
 static void mFilamentItem_HIPS()
 {
-bFilamentPreheatState=false;
-mFilamentItem(HIPS_PREHEAT_HOTEND_TEMP,HIPS_PREHEAT_HPB_TEMP);
+    bFilamentPreheatState = false;
+    mFilamentItem(HIPS_PREHEAT_HOTEND_TEMP, HIPS_PREHEAT_HPB_TEMP);
 }
 
 static void mFilamentItem_PP()
 {
-bFilamentPreheatState=false;
-mFilamentItem(PP_PREHEAT_HOTEND_TEMP,PP_PREHEAT_HPB_TEMP);
+    bFilamentPreheatState = false;
+    mFilamentItem(PP_PREHEAT_HOTEND_TEMP, PP_PREHEAT_HPB_TEMP);
 }
 
 static void mFilamentItem_FLEX()
 {
-bFilamentPreheatState=false;
-mFilamentItem(FLEX_PREHEAT_HOTEND_TEMP,FLEX_PREHEAT_HPB_TEMP);
+    bFilamentPreheatState = false;
+    mFilamentItem(FLEX_PREHEAT_HOTEND_TEMP, FLEX_PREHEAT_HPB_TEMP);
 }
 
-
 void mFilamentBack()
 {
-menu_back();
-if(eFilamentAction==FilamentAction::AutoLoad)
-     eFilamentAction=FilamentAction::None; // i.e. non-autoLoad
+    menu_back();
+    if (eFilamentAction == FilamentAction::AutoLoad ||
+            eFilamentAction == FilamentAction::Preheat)
+    {
+        eFilamentAction = FilamentAction::None; // i.e. non-autoLoad
+    }
 }
 
 void mFilamentMenu()
 {
-MENU_BEGIN();
-MENU_ITEM_FUNCTION_P(_T(MSG_MAIN),mFilamentBack);
-MENU_ITEM_SUBMENU_P(PSTR("PLA  -  " STRINGIFY(PLA_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PLA_PREHEAT_HPB_TEMP)),mFilamentItem_PLA);
-MENU_ITEM_SUBMENU_P(PSTR("PET  -  " STRINGIFY(PET_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PET_PREHEAT_HPB_TEMP)),mFilamentItem_PET);
-MENU_ITEM_SUBMENU_P(PSTR("ABS  -  " STRINGIFY(ABS_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(ABS_PREHEAT_HPB_TEMP)),mFilamentItem_ABS);
-MENU_ITEM_SUBMENU_P(PSTR("HIPS -  " STRINGIFY(HIPS_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(HIPS_PREHEAT_HPB_TEMP)),mFilamentItem_HIPS);
-MENU_ITEM_SUBMENU_P(PSTR("PP   -  " STRINGIFY(PP_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PP_PREHEAT_HPB_TEMP)),mFilamentItem_PP);
-MENU_ITEM_SUBMENU_P(PSTR("FLEX -  " STRINGIFY(FLEX_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(FLEX_PREHEAT_HPB_TEMP)),mFilamentItem_FLEX);
-MENU_END();
+    MENU_BEGIN();
+    if (!wizard_active) MENU_ITEM_FUNCTION_P(_T(MSG_MAIN),mFilamentBack);
+    if (farm_mode)
+    {
+        MENU_ITEM_FUNCTION_P(PSTR("farm   -  " STRINGIFY(FARM_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(FARM_PREHEAT_HPB_TEMP)), mFilamentItem_farm);
+        MENU_ITEM_FUNCTION_P(PSTR("nozzle -  " STRINGIFY(FARM_PREHEAT_HOTEND_TEMP) "/0"), mFilamentItem_farm_nozzle);
+    }
+    else
+    {
+        MENU_ITEM_SUBMENU_P(PSTR("PLA  -  " STRINGIFY(PLA_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PLA_PREHEAT_HPB_TEMP)),mFilamentItem_PLA);
+        MENU_ITEM_SUBMENU_P(PSTR("PET  -  " STRINGIFY(PET_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PET_PREHEAT_HPB_TEMP)),mFilamentItem_PET);
+        MENU_ITEM_SUBMENU_P(PSTR("ASA  -  " STRINGIFY(ASA_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(ASA_PREHEAT_HPB_TEMP)),mFilamentItem_ASA);
+        MENU_ITEM_SUBMENU_P(PSTR("ABS  -  " STRINGIFY(ABS_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(ABS_PREHEAT_HPB_TEMP)),mFilamentItem_ABS);
+        MENU_ITEM_SUBMENU_P(PSTR("HIPS -  " STRINGIFY(HIPS_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(HIPS_PREHEAT_HPB_TEMP)),mFilamentItem_HIPS);
+        MENU_ITEM_SUBMENU_P(PSTR("PP   -  " STRINGIFY(PP_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(PP_PREHEAT_HPB_TEMP)),mFilamentItem_PP);
+        MENU_ITEM_SUBMENU_P(PSTR("FLEX -  " STRINGIFY(FLEX_PREHEAT_HOTEND_TEMP) "/" STRINGIFY(FLEX_PREHEAT_HPB_TEMP)),mFilamentItem_FLEX);
+    }
+    if (!wizard_active && eFilamentAction == FilamentAction::Preheat) MENU_ITEM_FUNCTION_P(_T(MSG_COOLDOWN), lcd_cooldown);
+    MENU_END();
 }
 
 void mFilamentItemForce()
@@ -3071,7 +2894,7 @@ static void _lcd_move(const char *name, int axis, int min, int max)
 			if (max_software_endstops && current_position[axis] > max) current_position[axis] = max;
 			lcd_encoder = 0;
 			world2machine_clamp(current_position[X_AXIS], current_position[Y_AXIS]);
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], manual_feedrate[axis] / 60, active_extruder);
+			plan_buffer_line_curposXYZE(manual_feedrate[axis] / 60, active_extruder);
 			lcd_draw_update = 1;
 		}
 	}
@@ -3096,7 +2919,7 @@ static void lcd_move_e()
 			{
 				current_position[E_AXIS] += float((int)lcd_encoder) * move_menu_scale;
 				lcd_encoder = 0;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], manual_feedrate[E_AXIS] / 60, active_extruder);
+				plan_buffer_line_curposXYZE(manual_feedrate[E_AXIS] / 60, active_extruder);
 				lcd_draw_update = 1;
 			}
 		}
@@ -3287,7 +3110,7 @@ static void lcd_babystep_z()
 		_md->status = 1;
 		check_babystep();
 		
-		if(!is_sheet_initialized(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))){
+		if(!eeprom_is_sheet_initialized(eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))){
 			_md->babystepMemZ = 0;
 		}
 		else{
@@ -3634,7 +3457,7 @@ bool lcd_calibrate_z_end_stop_manual(bool only_z)
                     // Only move up, whatever direction the user rotates the encoder.
                     current_position[Z_AXIS] += fabs(lcd_encoder);
                     lcd_encoder = 0;
-                    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], manual_feedrate[Z_AXIS] / 60, active_extruder);
+                    plan_buffer_line_curposXYZE(manual_feedrate[Z_AXIS] / 60, active_extruder);
                 }
             }
             if (lcd_clicked()) {
@@ -4654,24 +4477,25 @@ static void lcd_silent_mode_set() {
 #endif //TMC2130
   st_current_init();
 #ifdef TMC2130
-  if (CrashDetectMenu && (SilentModeMenu != SILENT_MODE_NORMAL))
+  if (lcd_crash_detect_enabled() && (SilentModeMenu != SILENT_MODE_NORMAL))
 	  menu_submenu(lcd_crash_mode_info2);
   lcd_encoder_diff=0;                             // reset 'encoder buffer'
 #endif //TMC2130
 }
 
 #ifdef TMC2130
-static void lcd_crash_mode_set()
+static void crash_mode_switch()
 {
-	CrashDetectMenu = !CrashDetectMenu; //set also from crashdet_enable() and crashdet_disable()
-    if (CrashDetectMenu==0) {
-        crashdet_disable();
-    }else{
-        crashdet_enable();
+    if (lcd_crash_detect_enabled())
+    {
+        lcd_crash_detect_disable();
+    }
+    else
+    {
+        lcd_crash_detect_enable();
     }
 	if (IS_SD_PRINTING || is_usb_printing || (lcd_commands_type == LcdCommands::Layer1Cal)) menu_goto(lcd_tune_menu, 9, true, true);
 	else menu_goto(lcd_settings_menu, 9, true, true);
-    
 }
 #endif //TMC2130
  
@@ -4827,7 +4651,7 @@ void lcd_calibrate_pinda() {
 		
 		lcd_set_cursor(0, 1); lcd_puts_P(_T(MSG_PLEASE_WAIT));
 		current_position[E_AXIS] += e_shift_calibration;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate, active_extruder);
+		plan_buffer_line_curposXYZE(feedrate, active_extruder);
 		st_synchronize();
 
 		lcd_display_message_fullscreen_P(msg_e_cal_knob);
@@ -4850,7 +4674,7 @@ void lcd_calibrate_pinda() {
 				if (!planner_queue_full()) {
 					current_position[E_AXIS] += float(abs((int)lcd_encoder)) * 0.01; //0.05
 					lcd_encoder = 0;
-					plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate, active_extruder);
+					plan_buffer_line_curposXYZE(feedrate, active_extruder);
 					
 				}
 			}	
@@ -4900,7 +4724,6 @@ void lcd_toshiba_flash_air_compatibility_toggle()
 
 void lcd_v2_calibration()
 {
-	eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), selected_sheet);
 	if (mmu_enabled)
 	{
 	    const uint8_t filament = choose_menu_P(_i("Select PLA filament:"),_T(MSG_FILAMENT),_i("Cancel")); ////c=20 r=1  ////c=19 r=1
@@ -4970,7 +4793,7 @@ void lcd_language()
 static void wait_preheat()
 {
     current_position[Z_AXIS] = 100; //move in z axis to make space for loading filament
-    plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], homing_feedrate[Z_AXIS] / 60, active_extruder);
+    plan_buffer_line_curposXYZE(homing_feedrate[Z_AXIS] / 60, active_extruder);
     delay_keep_alive(2000);
     lcd_display_message_fullscreen_P(_T(MSG_WIZARD_HEATING));
 	lcd_set_custom_characters();
@@ -5385,11 +5208,11 @@ do\
         else MENU_ITEM_FUNCTION_P(_T(MSG_STEALTH_MODE_ON), lcd_silent_mode_set);\
         if (SilentModeMenu == SILENT_MODE_NORMAL)\
         {\
-            if (CrashDetectMenu == 0)\
+            if (lcd_crash_detect_enabled())\
             {\
-                MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_OFF), lcd_crash_mode_set);\
+                MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_ON), crash_mode_switch);\
             }\
-            else MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_ON), lcd_crash_mode_set);\
+            else MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_OFF), crash_mode_switch);\
         }\
         else MENU_ITEM_SUBMENU_P(_T(MSG_CRASHDETECT_NA), lcd_crash_mode_info);\
     }\
@@ -5732,37 +5555,38 @@ SETTINGS_VERSION;
 MENU_END();
 }
 
-void lcd_hw_setup_menu(void)                      // can not be "static"
+template <uint8_t number>
+static void select_sheet_menu()
 {
-MENU_BEGIN();
-MENU_ITEM_BACK_P(_T(bSettings?MSG_SETTINGS:MSG_BACK)); // i.e. default menu-item / menu-item after checking mismatch
-
-//strncpy(buffer,_i("Sheet"),sizeof(buffer));
-//strncpy(buffer,_i(" "),sizeof(buffer));
-//strncpy(buffer,EEPROM_Sheets_base->s[0].name,sizeof(buffer));
-
-//const char* menu = EEPROM_Sheets_base->s[0].name.c_str();
-
-//const char *b = new char(buffer);
-//const char *b = const char *b = new char(buffer);(buffer);
-//printf_P(_N("UVLO - end %d\n"), _millis() - time_start);
-//SERIAL_ECHOPGM(buffer);
-//SERIAL_ECHOPGM(reinterpret_cast<const char*>(buffer));
-//SERIAL_ECHOPGM("lakdjushasdjaljsdakjsdn");
-//char* p = &buffer[0];
-
-//MENU_ITEM_SUBMENU_P(reinterpret_cast<const char*>(p),lcd_sheet_menu);
+    selected_sheet = number;
+    lcd_sheet_menu();
+}
 
-//delete(b);
+static void sheets_menu()
+{
+    MENU_BEGIN();
+    MENU_ITEM_BACK_P(_i("HW Setup"));
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[0], select_sheet_menu<0>);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[1], select_sheet_menu<1>);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[2], select_sheet_menu<2>);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[3], select_sheet_menu<3>);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[4], select_sheet_menu<4>);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[5], select_sheet_menu<5>);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[6], select_sheet_menu<6>);
+    MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[7], select_sheet_menu<7>);
+    MENU_END();
+}
 
-MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[0], lcd_select_sheet_0_menu);
-MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[1], lcd_select_sheet_1_menu);
-MENU_ITEM_SUBMENU_E(EEPROM_Sheets_base->s[2], lcd_select_sheet_2_menu);   
+void lcd_hw_setup_menu(void)                      // can not be "static"
+{
+    MENU_BEGIN();
+    MENU_ITEM_BACK_P(_T(bSettings?MSG_SETTINGS:MSG_BACK)); // i.e. default menu-item / menu-item after checking mismatch
 
-SETTINGS_NOZZLE;
-MENU_ITEM_SUBMENU_P(_i("Checks"), lcd_checking_menu);
+    MENU_ITEM_SUBMENU_P(_i("Steel sheets"), sheets_menu);
+    SETTINGS_NOZZLE;
+    MENU_ITEM_SUBMENU_P(_i("Checks"), lcd_checking_menu);
 
-MENU_END();
+    MENU_END();
 }
 
 static void lcd_settings_menu()
@@ -6115,27 +5939,30 @@ uint8_t choose_menu_P(const char *header, const char *item, const char *last_ite
                 cursor_pos++;
             }
             enc_dif = lcd_encoder_diff;
+			Sound_MakeSound(e_SOUND_TYPE_EncoderMove);
 		}
 
 		if (cursor_pos > 3)
 		{		
-			Sound_MakeSound(e_SOUND_TYPE_BlindAlert);
             cursor_pos = 3;
             if (first < items_no - 3)
             {
                 first++;
                 lcd_clear();
+            } else { // here we are at the very end of the list
+				Sound_MakeSound(e_SOUND_TYPE_BlindAlert);
             }
         }
 
         if (cursor_pos < 1)
         {
-					Sound_MakeSound(e_SOUND_TYPE_BlindAlert);
             cursor_pos = 1;
             if (first > 0)
             {
                 first--;
                 lcd_clear();
+            } else { // here we are at the very end of the list
+				Sound_MakeSound(e_SOUND_TYPE_BlindAlert);
             }
         }
 
@@ -6165,7 +5992,6 @@ uint8_t choose_menu_P(const char *header, const char *item, const char *last_ite
         lcd_print(" ");
         lcd_set_cursor(0, cursor_pos);
         lcd_print(">");
-				Sound_MakeSound(e_SOUND_TYPE_EncoderMove);
         _delay(100);
 
 		if (lcd_clicked())
@@ -6424,13 +6250,13 @@ void unload_filament()
 	//		extr_unload2();
 
 	current_position[E_AXIS] -= 45;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 5200 / 60, active_extruder);
+	plan_buffer_line_curposXYZE(5200 / 60, active_extruder);
 	st_synchronize();
 	current_position[E_AXIS] -= 15;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 1000 / 60, active_extruder);
+	plan_buffer_line_curposXYZE(1000 / 60, active_extruder);
 	st_synchronize();
 	current_position[E_AXIS] -= 20;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], 1000 / 60, active_extruder);
+	plan_buffer_line_curposXYZE(1000 / 60, active_extruder);
 	st_synchronize();
 
 	lcd_display_message_fullscreen_P(_T(MSG_PULL_OUT_FILAMENT));
@@ -6721,40 +6547,7 @@ static void change_sheet()
     menu_back(3);
 }
 
-static void change_sheet_from_menu(){
-	uint8_t next_sheet = eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet))+1;
-	while(true){
-		if(next_sheet > 2) next_sheet = 0;
-		if(is_sheet_initialized(next_sheet)){
-			eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), next_sheet);
-			selected_sheet = next_sheet;
-			break;
-		}
-		else if (next_sheet == selected_sheet){
-			break;
-		}
-		else{
-			next_sheet++;
-		}
-	}
-	menu_back();
-}
 
-static void lcd_select_sheet_0_menu()
-{
-	selected_sheet = 0;
-	lcd_sheet_menu();
-}
-static void lcd_select_sheet_1_menu()
-{
-	selected_sheet = 1;
-	lcd_sheet_menu();
-}
-static void lcd_select_sheet_2_menu()
-{
-	selected_sheet = 2;
-	lcd_sheet_menu();
-}
 
 static void lcd_rename_sheet_menu()
 {
@@ -6802,37 +6595,41 @@ static void lcd_rename_sheet_menu()
 
 static void lcd_reset_sheet()
 {
-    struct MenuData
-    {
-        bool initialized;
-        uint8_t selected;
-        char name[sizeof(Sheet::name)];
-    };
-    static_assert(sizeof(menu_data)>= sizeof(MenuData),"MenuData doesn't fit into menu_data");
-    MenuData* menuData = (MenuData*)&(menu_data[0]);
-    eeprom_read_block(menuData->name, EEPROM_Sheets_base->s[selected_sheet].name, sizeof(Sheet::name));
-    
-	menuData->initialized = false;
-    strcpy_P(menuData->name, (char *)pgm_read_word(&(defaultSheetNames[selected_sheet])));
+    SheetName sheetName;
+    eeprom_default_sheet_name(selected_sheet, sheetName);
+	eeprom_update_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->s[selected_sheet].z_offset)),0xffff);
+	eeprom_update_block(sheetName.c,EEPROM_Sheets_base->s[selected_sheet].name,sizeof(Sheet::name));
+	if (selected_sheet == eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet)))
+	{
+        eeprom_switch_to_next_sheet();
+        if((-1 == eeprom_next_initialized_sheet(0)) && (CALIBRATION_STATUS_CALIBRATED == calibration_status()))
+        {
+            calibration_status_store(CALIBRATION_STATUS_LIVE_ADJUST);
+        }
+	}
 
+	menu_back();
+}
 
-	eeprom_update_word(reinterpret_cast<uint16_t *>(&(EEPROM_Sheets_base->s[selected_sheet].z_offset)),0xffff);
-	eeprom_update_block(menuData->name,EEPROM_Sheets_base->s[selected_sheet].name,sizeof(Sheet::name));
-	menu_back(2);
+//! @brief Activate selected_sheet and run first layer calibration
+static void activate_calibrate_sheet()
+{
+    eeprom_update_byte(&(EEPROM_Sheets_base->active_sheet), selected_sheet);
+    lcd_v2_calibration();
 }
 
 static void lcd_sheet_menu()
 {
     MENU_BEGIN();
-    MENU_ITEM_BACK_P(_T(MSG_HW_SETUP));
+    MENU_ITEM_BACK_P(_i("Steel sheets"));
 
-	if(is_sheet_initialized(selected_sheet)){
+	if(eeprom_is_sheet_initialized(selected_sheet)){
 	    MENU_ITEM_SUBMENU_P(_i("Select"), change_sheet); //// c=18
 	}
 
-    MENU_ITEM_SUBMENU_P(_T(MSG_V2_CALIBRATION), lcd_v2_calibration);
+    MENU_ITEM_SUBMENU_P(_T(MSG_V2_CALIBRATION), activate_calibrate_sheet);
     MENU_ITEM_SUBMENU_P(_i("Rename"), lcd_rename_sheet_menu); //// c=18
-	MENU_ITEM_SUBMENU_P(_i("Reset"), lcd_reset_sheet); //// c=18
+	MENU_ITEM_FUNCTION_P(_i("Reset"), lcd_reset_sheet); //// c=18
 
     MENU_END();
 }
@@ -6927,6 +6724,19 @@ static void lcd_main_menu()
   }
 #endif
 
+  if(!isPrintPaused && !IS_SD_PRINTING && !is_usb_printing && (lcd_commands_type != LcdCommands::Layer1Cal))
+  {
+    if (!farm_mode)
+    {
+        const int8_t sheet = eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet));
+        const int8_t nextSheet = eeprom_next_initialized_sheet(sheet);
+        if ((nextSheet >= 0) && (sheet != nextSheet)) // show menu only if we have 2 or more sheets initialized
+        {
+            MENU_ITEM_FUNCTION_E(EEPROM_Sheets_base->s[sheet], eeprom_switch_to_next_sheet);
+        }
+    }
+  }
+
 
   if (IS_SD_PRINTING || is_usb_printing || (lcd_commands_type == LcdCommands::Layer1Cal))
   {
@@ -6971,14 +6781,6 @@ static void lcd_main_menu()
     if(!isPrintPaused) MENU_ITEM_SUBMENU_P(_T(MSG_MENU_CALIBRATION), lcd_calibration_menu);
 
   }
-
-  if(!isPrintPaused && !IS_SD_PRINTING && !is_usb_printing && (lcd_commands_type != LcdCommands::Layer1Cal))
-  {
-    if (!farm_mode)
-    {
-	  MENU_ITEM_SUBMENU_SELECT_SHEET_E(EEPROM_Sheets_base->s[eeprom_read_byte(&(EEPROM_Sheets_base->active_sheet))], change_sheet_from_menu);
-    }
-  }
   
   if (!is_usb_printing && (lcd_commands_type != LcdCommands::Layer1Cal))
   {
@@ -7109,8 +6911,8 @@ static void lcd_tune_menu()
 
           if (SilentModeMenu == SILENT_MODE_NORMAL)
           {
-               if (CrashDetectMenu == 0) MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_OFF), lcd_crash_mode_set);
-               else MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_ON), lcd_crash_mode_set);
+               if (lcd_crash_detect_enabled()) MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_ON), crash_mode_switch);
+               else MENU_ITEM_FUNCTION_P(_T(MSG_CRASHDETECT_OFF), crash_mode_switch);
           }
           else MENU_ITEM_SUBMENU_P(_T(MSG_CRASHDETECT_NA), lcd_crash_mode_info);
      }
@@ -7514,7 +7316,7 @@ bool lcd_selftest()
 		//homeaxis(X_AXIS);
 		//homeaxis(Y_AXIS);
 		current_position[Z_AXIS] = current_position[Z_AXIS] + 10;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+		plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 		st_synchronize();
 		_progress = lcd_selftest_screen(TestScreen::AxisZ, _progress, 3, true, 1500);
 		_result = lcd_selfcheck_axis(2, Z_MAX_POS);
@@ -7528,7 +7330,7 @@ bool lcd_selftest()
 	if (_result)
 	{
 		current_position[Z_AXIS] = current_position[Z_AXIS] + 10;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+		plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 		st_synchronize();
 		_progress = lcd_selftest_screen(TestScreen::Home, 0, 2, true, 0);
 		bool bres = tmc2130_home_calibrate(X_AXIS);
@@ -7612,7 +7414,7 @@ bool lcd_selftest()
 
 static void reset_crash_det(unsigned char axis) {
 	current_position[axis] += 10;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 	st_synchronize();
 	if (eeprom_read_byte((uint8_t*)EEPROM_CRASH_DET)) tmc2130_sg_stop_on_crash = true;
 }
@@ -7636,7 +7438,7 @@ static bool lcd_selfcheck_axis_sg(unsigned char axis) {
 	if (axis == X_AXIS) { //there is collision between cables and PSU cover in X axis if Z coordinate is too low
 		
 		current_position[Z_AXIS] += 17;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+		plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 		tmc2130_home_enter(Z_AXIS_MASK);
 		st_synchronize();
 		tmc2130_home_exit();
@@ -7645,7 +7447,7 @@ static bool lcd_selfcheck_axis_sg(unsigned char axis) {
 // first axis length measurement begin	
 	
 	current_position[axis] -= (axis_length + margin);
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 
 	
 	st_synchronize();
@@ -7655,11 +7457,11 @@ static bool lcd_selfcheck_axis_sg(unsigned char axis) {
 	current_position_init = st_get_position_mm(axis);
 
 	current_position[axis] += 2 * margin;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 	st_synchronize();
 
 	current_position[axis] += axis_length;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 
 	st_synchronize();
 
@@ -7675,11 +7477,11 @@ static bool lcd_selfcheck_axis_sg(unsigned char axis) {
 
 
 	current_position[axis] -= margin;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 	st_synchronize();	
 
 	current_position[axis] -= (axis_length + margin);
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 		
 	st_synchronize();
 
@@ -7748,13 +7550,13 @@ static bool lcd_selfcheck_axis(int _axis, int _travel)
 
 	if (_axis == X_AXIS) {
 		current_position[Z_AXIS] += 17;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+		plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 	}
 
 	do {
 		current_position[_axis] = current_position[_axis] - 1;
 
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+		plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 		st_synchronize();
 #ifdef TMC2130
 		if ((READ(Z_MIN_PIN) ^ (bool)Z_MIN_ENDSTOP_INVERTING))
@@ -7808,7 +7610,7 @@ static bool lcd_selfcheck_axis(int _axis, int _travel)
 
 
 	//current_position[_axis] = current_position[_axis] + 15;
-	//plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	//plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 
 	if (!_stepresult)
 	{
@@ -7856,17 +7658,17 @@ static bool lcd_selfcheck_pulleys(int axis)
 	current_position_init = current_position[axis];
 
 	current_position[axis] += 2;
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 	for (i = 0; i < 5; i++) {
 		refresh_cmd_timeout();
 		current_position[axis] = current_position[axis] + move;
 		st_current_set(0, 850); //set motor current higher
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], 200, active_extruder);
+		plan_buffer_line_curposXYZE(200, active_extruder);
 		st_synchronize();
           if (SilentModeMenu != SILENT_MODE_OFF) st_current_set(0, tmp_motor[0]); //set back to normal operation currents
 		else st_current_set(0, tmp_motor_loud[0]); //set motor current back			
 		current_position[axis] = current_position[axis] - move;
-		plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], 50, active_extruder);
+		plan_buffer_line_curposXYZE(50, active_extruder);
 		st_synchronize();
 		if (((READ(X_MIN_PIN) ^ X_MIN_ENDSTOP_INVERTING) == 1) ||
 			((READ(Y_MIN_PIN) ^ Y_MIN_ENDSTOP_INVERTING) == 1)) {
@@ -7883,7 +7685,7 @@ static bool lcd_selfcheck_pulleys(int axis)
 			endstop_triggered = true;
 			if (current_position_init - 1 <= current_position[axis] && current_position_init + 1 >= current_position[axis]) {
 				current_position[axis] += (axis == X_AXIS) ? 13 : 9;
-				plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+				plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 				st_synchronize();
 				return(true);
 			}
@@ -7894,7 +7696,7 @@ static bool lcd_selfcheck_pulleys(int axis)
 		}
 		else {
 			current_position[axis] -= 1;
-			plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[3], manual_feedrate[0] / 60, active_extruder);
+			plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 			st_synchronize();
 			if (_millis() > timeout_counter) {
 				lcd_selftest_error(TestError::Pulley, (axis == 0) ? "X" : "Y", "");
@@ -7918,7 +7720,7 @@ static bool lcd_selfcheck_endstops()
 		if ((READ(Y_MIN_PIN) ^ Y_MIN_ENDSTOP_INVERTING) == 1) current_position[1] += 10;
 		if ((READ(Z_MIN_PIN) ^ Z_MIN_ENDSTOP_INVERTING) == 1) current_position[2] += 10;
 	}
-	plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], manual_feedrate[0] / 60, active_extruder);
+	plan_buffer_line_curposXYZE(manual_feedrate[0] / 60, active_extruder);
 	_delay(500);
 
 	if (((READ(X_MIN_PIN) ^ X_MIN_ENDSTOP_INVERTING) == 1) ||
@@ -8755,8 +8557,23 @@ uint8_t get_message_level()
 
 void menu_lcd_longpress_func(void)
 {
-	move_menu_scale = 1.0;
-	menu_submenu(lcd_move_z);
+    if (homing_flag || mesh_bed_leveling_flag || menu_menu == lcd_babystep_z || menu_menu == lcd_move_z)
+    {
+        // disable longpress during re-entry, while homing or calibration
+        lcd_quick_feedback();
+        return;
+    }
+
+    if (current_position[Z_AXIS] < Z_HEIGHT_HIDE_LIVE_ADJUST_MENU && (moves_planned() || IS_SD_PRINTING || is_usb_printing ))
+    {
+        lcd_clear();
+        menu_submenu(lcd_babystep_z);
+    }
+    else
+    {
+        move_menu_scale = 1.0;
+        menu_submenu(lcd_move_z);
+    }
 }
 
 void menu_lcd_charsetup_func(void)
@@ -8851,3 +8668,27 @@ void menu_lcd_lcdupdate_func(void)
 	lcd_send_status();
 	if (lcd_commands_type == LcdCommands::Layer1Cal) lcd_commands();
 }
+
+#ifdef TMC2130
+//! @brief Is crash detection enabled?
+//!
+//! @retval true crash detection enabled
+//! @retval false crash detection disabled
+bool lcd_crash_detect_enabled()
+{
+    return eeprom_read_byte((uint8_t*)EEPROM_CRASH_DET);
+}
+
+void lcd_crash_detect_enable()
+{
+    tmc2130_sg_stop_on_crash = true;
+    eeprom_update_byte((uint8_t*)EEPROM_CRASH_DET, 0xFF);
+}
+
+void lcd_crash_detect_disable()
+{
+    tmc2130_sg_stop_on_crash = false;
+    tmc2130_sg_crash = 0;
+    eeprom_update_byte((uint8_t*)EEPROM_CRASH_DET, 0x00);
+}
+#endif

Firmware/ultralcd.h

@@ -53,6 +53,11 @@ void lcd_menu_statistics();
 
 void lcd_menu_extruder_info();                    // NOT static due to using inside "Marlin_main" module ("manage_inactivity()")
 void lcd_menu_show_sensors_state();               // NOT static due to using inside "Marlin_main" module ("manage_inactivity()")
+#ifdef TMC2130
+bool lcd_crash_detect_enabled();
+void lcd_crash_detect_enable();
+void lcd_crash_detect_disable();
+#endif
 
 extern const char* lcd_display_message_fullscreen_P(const char *msg, uint8_t &nlines);
 extern const char* lcd_display_message_fullscreen_P(const char *msg);
@@ -162,6 +167,7 @@ enum class FilamentAction : uint_least8_t
     MmuUnLoad,
     MmuEject,
     MmuCut,
+    Preheat,
 };
 
 extern FilamentAction eFilamentAction;

Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h

@@ -257,7 +257,7 @@ BED SETTINGS
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 9     // Z probe to nozzle Y offset: -front +behind

Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h

@@ -256,7 +256,7 @@ BED SETTINGS
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 9     // Z probe to nozzle Y offset: -front +behind
@@ -319,35 +319,27 @@ PREHEAT SETTINGS
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
 #define FARM_PREHEAT_HPB_TEMP 80
-#define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
 #define PLA_PREHEAT_HPB_TEMP 55
-#define PLA_PREHEAT_FAN_SPEED 0  
 
 #define ASA_PREHEAT_HOTEND_TEMP 260
 #define ASA_PREHEAT_HPB_TEMP 105
-#define ASA_PREHEAT_FAN_SPEED 0
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
 #define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 0 
 
 #define HIPS_PREHEAT_HOTEND_TEMP 220
 #define HIPS_PREHEAT_HPB_TEMP 100
-#define HIPS_PREHEAT_FAN_SPEED 0 
 
 #define PP_PREHEAT_HOTEND_TEMP 254
 #define PP_PREHEAT_HPB_TEMP 100
-#define PP_PREHEAT_FAN_SPEED 0 
 
 #define PET_PREHEAT_HOTEND_TEMP 240
 #define PET_PREHEAT_HPB_TEMP 90
-#define PET_PREHEAT_FAN_SPEED 0 
 
 #define FLEX_PREHEAT_HOTEND_TEMP 230
 #define FLEX_PREHEAT_HPB_TEMP 50
-#define FLEX_PREHEAT_FAN_SPEED 0 
 
 /*------------------------------------
 THERMISTORS SETTINGS

Firmware/variants/1_75mm_MK25-RAMBo10a-E3Dv6full.h

@@ -314,7 +314,7 @@
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
@@ -377,35 +377,27 @@
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
 #define FARM_PREHEAT_HPB_TEMP 80
-#define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
 #define PLA_PREHEAT_HPB_TEMP 60
-#define PLA_PREHEAT_FAN_SPEED 0
 
 #define ASA_PREHEAT_HOTEND_TEMP 260
 #define ASA_PREHEAT_HPB_TEMP 105
-#define ASA_PREHEAT_FAN_SPEED 0
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
 #define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 0
 
 #define HIPS_PREHEAT_HOTEND_TEMP 220
 #define HIPS_PREHEAT_HPB_TEMP 100
-#define HIPS_PREHEAT_FAN_SPEED 0
 
 #define PP_PREHEAT_HOTEND_TEMP 254
 #define PP_PREHEAT_HPB_TEMP 100
-#define PP_PREHEAT_FAN_SPEED 0
 
 #define PET_PREHEAT_HOTEND_TEMP 230
 #define PET_PREHEAT_HPB_TEMP 85
-#define PET_PREHEAT_FAN_SPEED 0
 
 #define FLEX_PREHEAT_HOTEND_TEMP 240
 #define FLEX_PREHEAT_HPB_TEMP 50
-#define FLEX_PREHEAT_FAN_SPEED 0
 
 /*------------------------------------
  THERMISTORS SETTINGS

Firmware/variants/1_75mm_MK25-RAMBo13a-E3Dv6full.h

@@ -315,7 +315,7 @@
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
@@ -378,35 +378,27 @@
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
 #define FARM_PREHEAT_HPB_TEMP 80
-#define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
 #define PLA_PREHEAT_HPB_TEMP 60
-#define PLA_PREHEAT_FAN_SPEED 0
 
 #define ASA_PREHEAT_HOTEND_TEMP 260
 #define ASA_PREHEAT_HPB_TEMP 105
-#define ASA_PREHEAT_FAN_SPEED 0
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
 #define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 0
 
 #define HIPS_PREHEAT_HOTEND_TEMP 220
 #define HIPS_PREHEAT_HPB_TEMP 100
-#define HIPS_PREHEAT_FAN_SPEED 0
 
 #define PP_PREHEAT_HOTEND_TEMP 254
 #define PP_PREHEAT_HPB_TEMP 100
-#define PP_PREHEAT_FAN_SPEED 0
 
 #define PET_PREHEAT_HOTEND_TEMP 230
 #define PET_PREHEAT_HPB_TEMP 85
-#define PET_PREHEAT_FAN_SPEED 0
 
 #define FLEX_PREHEAT_HOTEND_TEMP 240
 #define FLEX_PREHEAT_HPB_TEMP 50
-#define FLEX_PREHEAT_FAN_SPEED 0
 
 /*------------------------------------
  THERMISTORS SETTINGS

Firmware/variants/1_75mm_MK25S-RAMBo10a-E3Dv6full.h

@@ -314,7 +314,7 @@
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
@@ -377,35 +377,27 @@
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
 #define FARM_PREHEAT_HPB_TEMP 80
-#define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
 #define PLA_PREHEAT_HPB_TEMP 60
-#define PLA_PREHEAT_FAN_SPEED 0
 
 #define ASA_PREHEAT_HOTEND_TEMP 260
 #define ASA_PREHEAT_HPB_TEMP 105
-#define ASA_PREHEAT_FAN_SPEED 0
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
 #define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 0
 
 #define HIPS_PREHEAT_HOTEND_TEMP 220
 #define HIPS_PREHEAT_HPB_TEMP 100
-#define HIPS_PREHEAT_FAN_SPEED 0
 
 #define PP_PREHEAT_HOTEND_TEMP 254
 #define PP_PREHEAT_HPB_TEMP 100
-#define PP_PREHEAT_FAN_SPEED 0
 
 #define PET_PREHEAT_HOTEND_TEMP 230
 #define PET_PREHEAT_HPB_TEMP 85
-#define PET_PREHEAT_FAN_SPEED 0
 
 #define FLEX_PREHEAT_HOTEND_TEMP 240
 #define FLEX_PREHEAT_HPB_TEMP 50
-#define FLEX_PREHEAT_FAN_SPEED 0
 
 /*------------------------------------
  THERMISTORS SETTINGS

Firmware/variants/1_75mm_MK25S-RAMBo13a-E3Dv6full.h

@@ -315,7 +315,7 @@
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
@@ -378,35 +378,27 @@
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
 #define FARM_PREHEAT_HPB_TEMP 80
-#define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
 #define PLA_PREHEAT_HPB_TEMP 60
-#define PLA_PREHEAT_FAN_SPEED 0
 
 #define ASA_PREHEAT_HOTEND_TEMP 260
 #define ASA_PREHEAT_HPB_TEMP 105
-#define ASA_PREHEAT_FAN_SPEED 0
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
 #define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 0
 
 #define HIPS_PREHEAT_HOTEND_TEMP 220
 #define HIPS_PREHEAT_HPB_TEMP 100
-#define HIPS_PREHEAT_FAN_SPEED 0
 
 #define PP_PREHEAT_HOTEND_TEMP 254
 #define PP_PREHEAT_HPB_TEMP 100
-#define PP_PREHEAT_FAN_SPEED 0
 
 #define PET_PREHEAT_HOTEND_TEMP 230
 #define PET_PREHEAT_HPB_TEMP 85
-#define PET_PREHEAT_FAN_SPEED 0
 
 #define FLEX_PREHEAT_HOTEND_TEMP 240
 #define FLEX_PREHEAT_HPB_TEMP 50
-#define FLEX_PREHEAT_FAN_SPEED 0
 
 /*------------------------------------
  THERMISTORS SETTINGS

Firmware/variants/1_75mm_MK3-EINSy10a-E3Dv6full.h

@@ -422,7 +422,7 @@
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
@@ -487,35 +487,27 @@
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
 #define FARM_PREHEAT_HPB_TEMP 80
-#define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
 #define PLA_PREHEAT_HPB_TEMP 60
-#define PLA_PREHEAT_FAN_SPEED 0
 
 #define ASA_PREHEAT_HOTEND_TEMP 260
 #define ASA_PREHEAT_HPB_TEMP 105
-#define ASA_PREHEAT_FAN_SPEED 0
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
 #define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 0
 
 #define HIPS_PREHEAT_HOTEND_TEMP 220
 #define HIPS_PREHEAT_HPB_TEMP 100
-#define HIPS_PREHEAT_FAN_SPEED 0
 
 #define PP_PREHEAT_HOTEND_TEMP 254
 #define PP_PREHEAT_HPB_TEMP 100
-#define PP_PREHEAT_FAN_SPEED 0
 
 #define PET_PREHEAT_HOTEND_TEMP 230
 #define PET_PREHEAT_HPB_TEMP 85
-#define PET_PREHEAT_FAN_SPEED 0
 
 #define FLEX_PREHEAT_HOTEND_TEMP 240
 #define FLEX_PREHEAT_HPB_TEMP 50
-#define FLEX_PREHEAT_FAN_SPEED 0
 
 /*------------------------------------
  THERMISTORS SETTINGS

Firmware/variants/1_75mm_MK3S-EINSy10a-E3Dv6full.h

@@ -424,7 +424,7 @@
 #define BED_ADJUSTMENT_UM_MAX 100
 
 #define MESH_HOME_Z_CALIB 0.2
-#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
+#define MESH_HOME_Z_SEARCH 5.0f           // Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
 #define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
@@ -489,35 +489,27 @@
 
 #define FARM_PREHEAT_HOTEND_TEMP 250
 #define FARM_PREHEAT_HPB_TEMP 80
-#define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
 #define PLA_PREHEAT_HPB_TEMP 60
-#define PLA_PREHEAT_FAN_SPEED 0
 
 #define ASA_PREHEAT_HOTEND_TEMP 260
 #define ASA_PREHEAT_HPB_TEMP 105
-#define ASA_PREHEAT_FAN_SPEED 0
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
 #define ABS_PREHEAT_HPB_TEMP 100
-#define ABS_PREHEAT_FAN_SPEED 0
 
 #define HIPS_PREHEAT_HOTEND_TEMP 220
 #define HIPS_PREHEAT_HPB_TEMP 100
-#define HIPS_PREHEAT_FAN_SPEED 0
 
 #define PP_PREHEAT_HOTEND_TEMP 254
 #define PP_PREHEAT_HPB_TEMP 100
-#define PP_PREHEAT_FAN_SPEED 0
 
 #define PET_PREHEAT_HOTEND_TEMP 230
 #define PET_PREHEAT_HPB_TEMP 85
-#define PET_PREHEAT_FAN_SPEED 0
 
 #define FLEX_PREHEAT_HOTEND_TEMP 240
 #define FLEX_PREHEAT_HPB_TEMP 50
-#define FLEX_PREHEAT_FAN_SPEED 0
 
 /*------------------------------------
  THERMISTORS SETTINGS

lang/lang-export.sh

@@ -1,4 +1,4 @@
-#!/bin/sh
+#!/bin/bash
 #
 # lang-export.sh - multi-language support script
 #  for generating lang_xx.po

lang/lang-import.sh

@@ -1,4 +1,4 @@
-#!/bin/sh
+#!/bin/bash
 #
 # lang-import.sh - multi-language support script
 #  for importing translated xx.po

lang/lang_en.txt

@@ -930,3 +930,147 @@
 
 #MSG_OFF
 " [off]"
+
+#
+"Back"
+
+#
+"Checks"
+
+#
+"False triggering"
+
+#
+"FINDA:"
+
+#
+"Firmware   [none]"
+
+#
+"Firmware [strict]"
+
+#
+"Firmware   [warn]"
+
+#
+"HW Setup"
+
+#
+"IR:"
+
+#
+"Magnets comp.[N/A]"
+
+#
+"Magnets comp.[Off]"
+
+#
+"Magnets comp. [On]"
+
+#
+"Mesh         [3x3]"
+
+#
+"Mesh         [7x7]"
+
+#
+"Mesh bed leveling"
+
+#
+"MK3S firmware detected on MK3 printer"
+
+#
+"MMU Mode [Normal]"
+
+#
+"MMU Mode[Stealth]"
+
+#
+"Mode change in progress ..."
+
+#
+"Model      [none]"
+
+#
+"Model    [strict]"
+
+#
+"Model      [warn]"
+
+#
+"Nozzle d.  [0.25]"
+
+#
+"Nozzle d.  [0.40]"
+
+#
+"Nozzle d.  [0.60]"
+
+#
+"Nozzle     [none]"
+
+#
+"Nozzle   [strict]"
+
+#
+"Nozzle     [warn]"
+
+#
+"G-code sliced for a different level. Continue?"
+
+#
+"G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+
+#
+"G-code sliced for a different printer type. Continue?"
+
+#
+"G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+
+#
+"G-code sliced for a newer firmware. Continue?"
+
+#
+"G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+
+#
+"PINDA:"
+
+#
+"Preheating to cut"
+
+#
+"Preheating to eject"
+
+#
+"Printer nozzle diameter differs from the G-code. Continue?"
+
+#
+"Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+
+#
+"Rename"
+
+#
+"Select"
+
+#
+"Sensor info"
+
+#
+"Sheet"
+
+#
+"Sound     [assist]"
+
+#
+"Steel sheets"
+
+#
+"Z-correct:"
+
+#
+"Z-probe nr.    [1]"
+
+#
+"Z-probe nr.    [3]"

lang/lang_en_cz.txt

@@ -24,7 +24,7 @@
 
 #MSG_BABYSTEPPING_Z c=15
 "Adjusting Z:"
-"Dostavovani Z:"
+"Doladeni Z:"
 
 #MSG_SELFTEST_CHECK_ALLCORRECT c=20
 "All correct      "
@@ -316,7 +316,7 @@
 
 #
 "Filam. runouts"
-"Vypadky filamentu"
+"Vypadky filam."
 
 #MSG_FILAMENT_CLEAN c=20 r=2
 "Filament extruding & with correct color?"
@@ -688,7 +688,7 @@
 
 #
 "Nozzle FAN"
-"Trysk. vent."
+"Tryska V."
 
 #MSG_PAUSE_PRINT
 "Pause print"
@@ -792,7 +792,7 @@
 
 #MSG_WIZARD_HEATING c=20 r=3
 "Preheating nozzle. Please wait."
-"Predehrivam trysku. Prosim cekejte."
+"Predehrev trysky. Prosim cekejte."
 
 #
 "Please upgrade."
@@ -812,15 +812,15 @@
 
 #
 "Preheating to load"
-"Predehrivam k zavedeni"
+"Predehrev k zavedeni"
 
 #
 "Preheating to unload"
-"Predehrivam k vyjmuti"
+"Predehrev k vyjmuti"
 
 #MSG_SELFTEST_PRINT_FAN_SPEED c=18
 "Print fan:"
-"Tiskovy vent.:"
+"Tiskovy v:"
 
 #MSG_CARD_MENU
 "Print from SD"
@@ -828,7 +828,7 @@
 
 #
 "Press the knob"
-"Stisknete tlacitko"
+"Stisknete hl. tlacitko"
 
 #MSG_PRINT_PAUSED c=20 r=1
 "Print paused"
@@ -844,7 +844,7 @@
 
 #
 "Print FAN"
-"Tiskovy vent."
+"Tiskovy v"
 
 #MSG_PRUSA3D
 "prusa3d.com"
@@ -1240,4 +1240,196 @@
 
 #MSG_OFF
 " [off]"
+" [vyp]"
+
+#
+"Back"
+"Zpet"
+
+#
+"Checks"
+"Kontrola"
+
+#
+"False triggering"
+"Falesne spusteni"
+
+#
+"FINDA:"
+"\x00"
+
+#
+"Firmware   [none]"
+"Firmware  [Zadne]"
+
+#
+"Firmware [strict]"
+"Firmware [Prisne]"
+
+#
+"Firmware   [warn]"
+"Firmware[Varovat]"
+
+#
+"HW Setup"
+"HW nastaveni"
+
+#
+"IR:"
 "\x00"
+
+#
+"Magnets comp.[N/A]"
+"Komp. magnetu[N/A]"
+
+#
+"Magnets comp.[Off]"
+"Komp. magnetu[Vyp]"
+
+#
+"Magnets comp. [On]"
+"Komp. magnetu[Zap]"
+
+#
+"Mesh         [3x3]"
+"Mesh         [3x3]"
+
+#
+"Mesh         [7x7]"
+"Mesh         [7x7]"
+
+#
+"Mesh bed leveling"
+"Mesh Bed Leveling"
+
+#
+"MK3S firmware detected on MK3 printer"
+"MK3S firmware detekovan na tiskarne MK3"
+
+#
+"MMU Mode [Normal]"
+"MMU mod  [Normal]"
+
+#
+"MMU Mode[Stealth]"
+"MMU Mod   [Tichy]"
+
+#
+"Mode change in progress ..."
+"Probiha zmena modu..."
+
+#
+"Model      [none]"
+"Model     [Zadne]"
+
+#
+"Model    [strict]"
+"Model    [Prisne]"
+
+#
+"Model      [warn]"
+"Model   [Varovat]"
+
+#
+"Nozzle d.  [0.25]"
+"Tryska     [0.25]"
+
+#
+"Nozzle d.  [0.40]"
+"Tryska     [0.40]"
+
+#
+"Nozzle d.  [0.60]"
+"Tryska     [0.60]"
+
+#
+"Nozzle     [none]"
+"Tryska    [Zadne]"
+
+#
+"Nozzle   [strict]"
+"Tryska   [Prisne]"
+
+#
+"Nozzle     [warn]"
+"Tryska  [Varovat]"
+
+#
+"G-code sliced for a different level. Continue?"
+"\x00"
+
+#
+"G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+"\x00"
+
+#
+"G-code sliced for a different printer type. Continue?"
+"G-code je pripraven pro jiny typ tiskarny. Pokracovat?"
+
+#
+"G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+"G-code je pripraven pro jiny typ tiskarny. Prosim preslicujte model znovu. Tisk zrusen."
+
+#
+"G-code sliced for a newer firmware. Continue?"
+"G-code je pripraven pro novejsi firmware. Pokracovat?"
+
+#
+"G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+"G-code je pripraven pro novejsi firmware. Prosim aktualizujte firmware. Tisk zrusen."
+
+#
+"PINDA:"
+"\x00"
+
+#
+"Preheating to cut"
+"Predehrev k ustrizeni"
+
+#
+"Preheating to eject"
+"Predehrev k vysunuti"
+
+#
+"Printer nozzle diameter differs from the G-code. Continue?"
+"Prumer trysky tiskarny se lisi od G-code. Pokracovat?"
+
+#
+"Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+"Prumer trysky tiskarny se lisi od G-code. Prosim zkontrolujte nastaveni. Tisk zrusen."
+
+#
+"Rename"
+"Prejmenovat"
+
+#
+"Select"
+"Vybrat"
+
+#
+"Sensor info"
+"Senzor info"
+
+#
+"Sheet"
+"Plat"
+
+#
+"Sound     [assist]"
+"Zvuk      [Asist.]"
+
+#
+"Steel sheets"
+"Tiskove platy"
+
+#
+"Z-correct:"
+"Korekce Z:"
+
+#
+"Z-probe nr.    [1]"
+"Pocet mereni Z [1]"
+
+#
+"Z-probe nr.    [3]"
+"Pocet mereni Z [3]"

lang/lang_en_de.txt

@@ -24,11 +24,11 @@
 
 #MSG_BABYSTEPPING_Z c=15
 "Adjusting Z:"
-"Z Einstellung:"
+"Z Anpassen:"
 
 #MSG_SELFTEST_CHECK_ALLCORRECT c=20
 "All correct      "
-"Alles richtig "
+"Alles richtig    "
 
 #MSG_WIZARD_DONE c=20 r=8
 "All is done. Happy printing!"
@@ -688,7 +688,7 @@
 
 #
 "Nozzle FAN"
-"Duesen Luefter"
+"Duesevent."
 
 #MSG_PAUSE_PRINT
 "Pause print"
@@ -844,7 +844,7 @@
 
 #
 "Print FAN"
-"Druckluefter"
+"Druckvent"
 
 #MSG_PRUSA3D
 "prusa3d.com"
@@ -884,7 +884,7 @@
 
 #MSG_BED_CORRECTION_RIGHT c=14 r=1
 "Right side[um]"
-"Rechts [um]"
+"Rechts    [um]"
 
 #MSG_SECOND_SERIAL_ON c=17 r=1
 "RPi port     [on]"
@@ -928,7 +928,7 @@
 
 #MSG_SELFTEST
 "Selftest         "
-"Selbsttest "
+"Selbsttest       "
 
 #MSG_SELFTEST_ERROR
 "Selftest error !"
@@ -972,7 +972,7 @@
 
 #MSG_SORT_NONE c=17 r=1
 "Sort       [none]"
-"Sort.     [Keine]"
+"Sort.      [ohne]"
 
 #MSG_SORT_TIME c=17 r=1
 "Sort       [time]"
@@ -980,7 +980,7 @@
 
 #
 "Severe skew"
-"Schwerer Schraeglauf"
+"Schwer.Schr"
 
 #MSG_SORT_ALPHA c=17 r=1
 "Sort   [alphabet]"
@@ -996,7 +996,7 @@
 
 #
 "Slight skew"
-"Leichter Schraeglauf"
+"Leicht.Schr"
 
 #MSG_SOUND_MUTE c=17 r=1
 "Sound      [mute]"
@@ -1036,7 +1036,7 @@
 
 #MSG_STOPPED
 "STOPPED. "
-"GESTOPPT. "
+"GESTOPPT."
 
 #MSG_SUPPORT
 "Support"
@@ -1048,15 +1048,15 @@
 
 #MSG_TEMP_CALIBRATION c=20 r=1
 "Temp. cal.          "
-"Temp Kalib. "
+"Temp Kalib.         "
 
 #MSG_TEMP_CALIBRATION_ON c=20 r=1
 "Temp. cal.   [on]"
-"Temp. Kal.   [AN]"
+"Temp. Kal.   [an]"
 
 #MSG_TEMP_CALIBRATION_OFF c=20 r=1
 "Temp. cal.  [off]"
-"Temp. Kal.  [AUS]"
+"Temp. Kal.  [aus]"
 
 #MSG_CALIBRATION_PINDA_MENU c=17 r=1
 "Temp. calibration"
@@ -1241,4 +1241,196 @@
 
 #MSG_OFF
 " [off]"
+" [aus]"
+
+#
+"Back"
+"Zurueck"
+
+#
+"Checks"
+"\x00"
+
+#
+"False triggering"
+"Falschtriggerung"
+
+#
+"FINDA:"
+"\x00"
+
+#
+"Firmware   [none]"
+"Firmware   [ohne]"
+
+#
+"Firmware [strict]"
+"Firmware [streng]"
+
+#
+"Firmware   [warn]"
+"\x00"
+
+#
+"HW Setup"
+"HW Einstellungen"
+
+#
+"IR:"
+"\x00"
+
+#
+"Magnets comp.[N/A]"
+"Magnet Komp.  [nv]"
+
+#
+"Magnets comp.[Off]"
+"Magnet Komp. [Aus]"
+
+#
+"Magnets comp. [On]"
+"Magnet Komp.  [An]"
+
+#
+"Mesh         [3x3]"
+"\x00"
+
+#
+"Mesh         [7x7]"
 "\x00"
+
+#
+"Mesh bed leveling"
+"Mesh Bett Ausgleich"
+
+#
+"MK3S firmware detected on MK3 printer"
+"MK3S-Firmware auf MK3-Drucker erkannt"
+
+#
+"MMU Mode [Normal]"
+"MMU Modus[Normal]"
+
+#
+"MMU Mode[Stealth]"
+"MMU Mod.[Stealth]"
+
+#
+"Mode change in progress ..."
+"Moduswechsel erfolgt..."
+
+#
+"Model      [none]"
+"Modell     [ohne]"
+
+#
+"Model    [strict]"
+"Modell   [streng]"
+
+#
+"Model      [warn]"
+"Modell     [warn]"
+
+#
+"Nozzle d.  [0.25]"
+"Duese D.   [0.25]"
+
+#
+"Nozzle d.  [0.40]"
+"Duese D.   [0.40]"
+
+#
+"Nozzle d.  [0.60]"
+"Duese D.   [0.60]"
+
+#
+"Nozzle     [none]"
+"Duese      [ohne]"
+
+#
+"Nozzle   [strict]"
+"Duese    [streng]"
+
+#
+"Nozzle     [warn]"
+"Duese      [warn]"
+
+#
+"G-code sliced for a different level. Continue?"
+"G-Code ist fuer einen anderen Level geslict. Fortfahren?"
+
+#
+"G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+"G-Code ist fuer einen anderen Level geslict. Bitte slicen Sie das Modell erneut. Druck abgebrochen."
+
+#
+"G-code sliced for a different printer type. Continue?"
+"G-Code ist fuer einen anderen Drucker geslict. Fortfahren?"
+
+#
+"G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+"G-Code ist fuer einen anderen Drucker geslict. Bitte slicen Sie das Modell erneut. Druck abgebrochen."
+
+#
+"G-code sliced for a newer firmware. Continue?"
+"G-Code ist fuer eine neuere Firmware geslict. Fortfahren?"
+
+#
+"G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+"G-Code ist fuer eine neuere Firmware geslict. Bitte die Firmware updaten. Druck abgebrochen."
+
+#
+"PINDA:"
+"\x00"
+
+#
+"Preheating to cut"
+"Heizen zum Schnitt"
+
+#
+"Preheating to eject"
+"Heizen zum Auswurf"
+
+#
+"Printer nozzle diameter differs from the G-code. Continue?"
+"Der Durchmesser der Druckerduese weicht vom G-Code ab. Fortfahren?"
+
+#
+"Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+"Der Durchmesser der Druckerduese weicht vom G-Code ab. Bitte ueberpruefen Sie den Wert in den Einstellungen. Druck abgebrochen."
+
+#
+"Rename"
+"Umbenennen"
+
+#
+"Select"
+"Auswahl"
+
+#
+"Sensor info"
+"Sensor Info"
+
+#
+"Sheet"
+"Blech"
+
+#
+"Sound     [assist]"
+"Sound     [Assist]"
+
+#
+"Steel sheets"
+"Stahlbleche"
+
+#
+"Z-correct:"
+"Z-Korrektur:"
+
+#
+"Z-probe nr.    [1]"
+"Z-Probe Nr.    [1]"
+
+#
+"Z-probe nr.    [3]"
+"Z-Probe Nr.    [3]"

lang/lang_en_es.txt

@@ -24,7 +24,7 @@
 
 #MSG_BABYSTEPPING_Z c=15
 "Adjusting Z:"
-"Ajustar Z:"
+"Ajustando Z:"
 
 #MSG_SELFTEST_CHECK_ALLCORRECT c=20
 "All correct      "
@@ -104,7 +104,7 @@
 
 #MSG_BED
 "Bed"
-"Base calefactable "
+"Base"
 
 #MSG_MENU_BELT_STATUS c=15 r=1
 "Belt status"
@@ -216,7 +216,7 @@
 
 #MSG_EXTRUDER_CORRECTION c=10
 "E-correct:"
-"E-correcion:"
+"Correccion-E:"
 
 #MSG_EJECT_FILAMENT c=17 r=1
 "Eject filament"
@@ -256,7 +256,7 @@
 
 #MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
 "Extruder fan:"
-"Ventilador del extrusor:"
+"Vent.extrusor:"
 
 #MSG_INFO_EXTRUDER c=15 r=1
 "Extruder info"
@@ -568,7 +568,7 @@
 
 #
 "Measured skew"
-"Desviacion medida:"
+"Desviacion med:"
 
 #
 "MMU fails"
@@ -648,7 +648,7 @@
 
 #
 "N/A"
-"No disponible"
+"N/A"
 
 #MSG_NO
 "No"
@@ -672,7 +672,7 @@
 
 #MSG_WIZARD_WILL_PREHEAT c=20 r=4
 "Now I will preheat nozzle for PLA."
-"Voy a precalentar la boquilla para PLA ahora."
+"Ahora precalentare la boquilla para PLA."
 
 #MSG_NOZZLE
 "Nozzle"
@@ -688,7 +688,7 @@
 
 #
 "Nozzle FAN"
-"Ventilador de capa"
+"Vent. capa"
 
 #MSG_PAUSE_PRINT
 "Pause print"
@@ -820,7 +820,7 @@
 
 #MSG_SELFTEST_PRINT_FAN_SPEED c=18
 "Print fan:"
-"Ventilador del fusor:"
+"Vent.fusor:"
 
 #MSG_CARD_MENU
 "Print from SD"
@@ -844,7 +844,7 @@
 
 #
 "Print FAN"
-"Ventilador del extrusor"
+"Vent.extr"
 
 #MSG_PRUSA3D
 "prusa3d.com"
@@ -880,7 +880,7 @@
 
 #MSG_RESUMING_PRINT c=20 r=1
 "Resuming print"
-"Resumiendo impresion"
+"Continuando impresion"
 
 #MSG_BED_CORRECTION_RIGHT c=14 r=1
 "Right side[um]"
@@ -972,15 +972,15 @@
 
 #MSG_SORT_NONE c=17 r=1
 "Sort       [none]"
-"Ordenar    [nada]"
+"Ordenar [ninguno]"
 
 #MSG_SORT_TIME c=17 r=1
 "Sort       [time]"
-"Ordenar   [Fecha]"
+"Ordenar  [tiempo]"
 
 #
 "Severe skew"
-"Inclinacion severa"
+"Incl.severa"
 
 #MSG_SORT_ALPHA c=17 r=1
 "Sort   [alphabet]"
@@ -996,7 +996,7 @@
 
 #
 "Slight skew"
-"Ligeramente inclinado"
+"Liger.incl."
 
 #MSG_SOUND_MUTE c=17 r=1
 "Sound      [mute]"
@@ -1052,11 +1052,11 @@
 
 #MSG_TEMP_CALIBRATION_ON c=20 r=1
 "Temp. cal.   [on]"
-"Cal. temp.   [ON]"
+"Cal. temp.   [on]"
 
 #MSG_TEMP_CALIBRATION_OFF c=20 r=1
 "Temp. cal.  [off]"
-"Cal. temp.  [OFF]"
+"Cal. temp.  [off]"
 
 #MSG_CALIBRATION_PINDA_MENU c=17 r=1
 "Temp. calibration"
@@ -1200,7 +1200,7 @@
 
 #
 "X-correct:"
-"X-correcion:"
+"Correccion-X:"
 
 #MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
 "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
@@ -1236,8 +1236,200 @@
 
 #
 "Y-correct:"
-"Y-correcion:"
+"Correccion-Y:"
 
 #MSG_OFF
 " [off]"
+" [apagado]"
+
+#
+"Back"
+"atras"
+
+#
+"Checks"
+"Comprobaciones"
+
+#
+"False triggering"
+"Falsa activacion"
+
+#
+"FINDA:"
+"FINDA:"
+
+#
+"Firmware   [none]"
+"Firmware[ninguno]"
+
+#
+"Firmware [strict]"
+"Firmware[estrict]"
+
+#
+"Firmware   [warn]"
+"Firmware  [aviso]"
+
+#
+"HW Setup"
+"Configuracion HW"
+
+#
+"IR:"
 "\x00"
+
+#
+"Magnets comp.[N/A]"
+"Comp. imanes [N/A]"
+
+#
+"Magnets comp.[Off]"
+"Comp. imanes [Off]"
+
+#
+"Magnets comp. [On]"
+"Comp. imanes  [On]"
+
+#
+"Mesh         [3x3]"
+"Malla        [3x3]"
+
+#
+"Mesh         [7x7]"
+"Malla        [7x7]"
+
+#
+"Mesh bed leveling"
+"Nivelacion Malla Base"
+
+#
+"MK3S firmware detected on MK3 printer"
+"Firmware MK3S detectado en impresora MK3"
+
+#
+"MMU Mode [Normal]"
+"Modo MMU [Normal]"
+
+#
+"MMU Mode[Stealth]"
+"Modo MMU[Silenci]"
+
+#
+"Mode change in progress ..."
+"Cambio de modo progresando ..."
+
+#
+"Model      [none]"
+"Modelo  [ninguno]"
+
+#
+"Model    [strict]"
+"Modelo [estricto]"
+
+#
+"Model      [warn]"
+"Modelo    [aviso]"
+
+#
+"Nozzle d.  [0.25]"
+"Diam. nozzl[0.25]"
+
+#
+"Nozzle d.  [0.40]"
+"Diam. nozzl[0.40]"
+
+#
+"Nozzle d.  [0.60]"
+"Diam. nozzl[0.60]"
+
+#
+"Nozzle     [none]"
+"Nozzle  [ninguno]"
+
+#
+"Nozzle   [strict]"
+"Nozzle [estricto]"
+
+#
+"Nozzle     [warn]"
+"Nozzle    [aviso]"
+
+#
+"G-code sliced for a different level. Continue?"
+"Codigo G laminado para un nivel diferente. ?Continuar?"
+
+#
+"G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+"Codigo G laminado para un nivel diferente. Por favor relamina el modelo de nuevo. Impresion cancelada."
+
+#
+"G-code sliced for a different printer type. Continue?"
+"Codigo G laminado para un tipo de impresora diferente. ?Continuar?"
+
+#
+"G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+"Codigo G laminado para una impresora diferente. Por favor relamina el modelo de nuevo. Impresion cancelada."
+
+#
+"G-code sliced for a newer firmware. Continue?"
+"Codigo G laminado para nuevo firmware. ?Continuar?"
+
+#
+"G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+"Codigo G laminado para nuevo firmware. Por favor actualiza el firmware. Impresion cancelada."
+
+#
+"PINDA:"
+"PINDA:"
+
+#
+"Preheating to cut"
+"Precalentando para laminar"
+
+#
+"Preheating to eject"
+"Precalentar para expulsar"
+
+#
+"Printer nozzle diameter differs from the G-code. Continue?"
+"Diametro nozzle impresora difiere de cod.G. ?Continuar?"
+
+#
+"Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+"Diametro nozzle Impresora difiere de cod.G. Comprueba los valores en ajustes. Impresion cancelada."
+
+#
+"Rename"
+"Renombrar"
+
+#
+"Select"
+"Seleccionar"
+
+#
+"Sensor info"
+"Info sensor"
+
+#
+"Sheet"
+"Lamina"
+
+#
+"Sound     [assist]"
+"Sonido  [asistido]"
+
+#
+"Steel sheets"
+"Lamina de acero"
+
+#
+"Z-correct:"
+"Correccion-Z:"
+
+#
+"Z-probe nr.    [1]"
+"Z-sensor nr.   [1]"
+
+#
+"Z-probe nr.    [3]"
+"Z-sensor nr.   [3]"

lang/lang_en_fr.txt

@@ -24,7 +24,7 @@
 
 #MSG_BABYSTEPPING_Z c=15
 "Adjusting Z:"
-"Ajust. de Z:"
+"Ajuster Z :"
 
 #MSG_SELFTEST_CHECK_ALLCORRECT c=20
 "All correct      "
@@ -172,15 +172,15 @@
 
 #MSG_CRASHDETECT_ON
 "Crash det.   [on]"
-"Detect. crash[on]"
+"Detect.crash [on]"
 
 #MSG_CRASHDETECT_NA
 "Crash det.  [N/A]"
-"Detect. crash [N/A]"
+"Detect.crash[N/A]"
 
 #MSG_CRASHDETECT_OFF
 "Crash det.  [off]"
-"Detect. crash[off]"
+"Detect.crash[off]"
 
 #MSG_CRASH_DETECTED c=20 r=1
 "Crash detected."
@@ -288,7 +288,7 @@
 
 #MSG_FAN_SPEED c=14
 "Fan speed"
-"Vitesse ventil"
+"Vitesse vent."
 
 #MSG_SELFTEST_FAN c=20
 "Fan test"
@@ -604,7 +604,7 @@
 
 #MSG_STEALTH_MODE_ON
 "Mode    [Stealth]"
-"Mode [Furtif]"
+"Mode     [Furtif]"
 
 #MSG_AUTO_MODE_ON
 "Mode [auto power]"
@@ -612,7 +612,7 @@
 
 #MSG_SILENT_MODE_OFF
 "Mode [high power]"
-"Mode [haute puiss]"
+"Mode[haute puiss]"
 
 #
 "MMU2 connected"
@@ -688,7 +688,7 @@
 
 #
 "Nozzle FAN"
-"Ventilateur buse"
+"Vent. buse"
 
 #MSG_PAUSE_PRINT
 "Pause print"
@@ -804,7 +804,7 @@
 
 #
 "Power failures"
-"Coupures de courant"
+"Coup.de courant"
 
 #MSG_PRINT_ABORTED c=20
 "Print aborted"
@@ -820,7 +820,7 @@
 
 #MSG_SELFTEST_PRINT_FAN_SPEED c=18
 "Print fan:"
-"Ventilo impr. :"
+"Vent.impr:"
 
 #MSG_CARD_MENU
 "Print from SD"
@@ -844,7 +844,7 @@
 
 #
 "Print FAN"
-"Ventilo impression"
+"Vent.impr"
 
 #MSG_PRUSA3D
 "prusa3d.com"
@@ -868,7 +868,7 @@
 
 #MSG_CALIBRATE_BED_RESET
 "Reset XYZ calibr."
-"Reinit. calibr. XYZ"
+"Reinit.calibr. XYZ"
 
 #MSG_BED_CORRECTION_RESET
 "Reset"
@@ -888,11 +888,11 @@
 
 #MSG_SECOND_SERIAL_ON c=17 r=1
 "RPi port     [on]"
-"Port RPi [on]"
+"Port RPi     [on]"
 
 #MSG_SECOND_SERIAL_OFF c=17 r=1
 "RPi port    [off]"
-"Port RPi [off]"
+"Port RPi    [off]"
 
 #MSG_WIZARD_RERUN c=20 r=7
 "Running Wizard will delete current calibration results and start from the beginning. Continue?"
@@ -904,7 +904,7 @@
 
 #MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
 "SD card [flshAir]"
-"Carte SD [flashAir]"
+"CarteSD[flashAir]"
 
 #
 "Right"
@@ -972,7 +972,7 @@
 
 #MSG_SORT_NONE c=17 r=1
 "Sort       [none]"
-"Tri :     [aucun]"
+"Tri       [aucun]"
 
 #MSG_SORT_TIME c=17 r=1
 "Sort       [time]"
@@ -980,7 +980,7 @@
 
 #
 "Severe skew"
-"Deviation severe"
+"Deviat.sev."
 
 #MSG_SORT_ALPHA c=17 r=1
 "Sort   [alphabet]"
@@ -992,15 +992,15 @@
 
 #MSG_SOUND_LOUD c=17 r=1
 "Sound      [loud]"
-"Son [fort]"
+"Son        [fort]"
 
 #
 "Slight skew"
-"Deviation legere"
+"Deviat.leg."
 
 #MSG_SOUND_MUTE c=17 r=1
 "Sound      [mute]"
-"Son [muet]"
+"Son        [muet]"
 
 #
 "Some problem encountered, Z-leveling enforced ..."
@@ -1008,11 +1008,11 @@
 
 #MSG_SOUND_ONCE c=17 r=1
 "Sound      [once]"
-"Son [une fois]"
+"Son    [une fois]"
 
 #MSG_SOUND_SILENT c=17 r=1
 "Sound    [silent]"
-"Son [silencieux]"
+"Son  [silencieux]"
 
 #MSG_SPEED
 "Speed"
@@ -1240,4 +1240,196 @@
 
 #MSG_OFF
 " [off]"
+" [off]"
+
+#
+"Back"
+"Retour"
+
+#
+"Checks"
+"Verifications"
+
+#
+"False triggering"
+"Faux declenchement"
+
+#
+"FINDA:"
+"FINDA:"
+
+#
+"Firmware   [none]"
+"Firmware [aucune]"
+
+#
+"Firmware [strict]"
+"Firmware[stricte]"
+
+#
+"Firmware   [warn]"
+"Firmware  [avert]"
+
+#
+"HW Setup"
+"Config HW"
+
+#
+"IR:"
+"IR:"
+
+#
+"Magnets comp.[N/A]"
+"Comp. aimants[N/A]"
+
+#
+"Magnets comp.[Off]"
+"Comp. aimants[Off]"
+
+#
+"Magnets comp. [On]"
+"Comp. aimants [On]"
+
+#
+"Mesh         [3x3]"
+"\x00"
+
+#
+"Mesh         [7x7]"
+"\x00"
+
+#
+"Mesh bed leveling"
 "\x00"
+
+#
+"MK3S firmware detected on MK3 printer"
+"Firmware MK3S detecte sur imprimante MK3"
+
+#
+"MMU Mode [Normal]"
+"Mode MMU [Normal]"
+
+#
+"MMU Mode[Stealth]"
+"Mode MMU [Furtif]"
+
+#
+"Mode change in progress ..."
+"Changement de mode en cours..."
+
+#
+"Model      [none]"
+"Modele   [aucune]"
+
+#
+"Model    [strict]"
+"Modele  [stricte]"
+
+#
+"Model      [warn]"
+"Modele    [avert]"
+
+#
+"Nozzle d.  [0.25]"
+"Diam. buse [0.25]"
+
+#
+"Nozzle d.  [0.40]"
+"Diam. buse [0.40]"
+
+#
+"Nozzle d.  [0.60]"
+"Diam. buse [0.60]"
+
+#
+"Nozzle     [none]"
+"Buse     [aucune]"
+
+#
+"Nozzle   [strict]"
+"Buse    [stricte]"
+
+#
+"Nozzle     [warn]"
+"Buse      [avert]"
+
+#
+"G-code sliced for a different level. Continue?"
+"\x00"
+
+#
+"G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+"\x00"
+
+#
+"G-code sliced for a different printer type. Continue?"
+"Le G-code a ete prepare pour une autre version de l'imprimante. Continuer?"
+
+#
+"G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+"Le G-code a ete prepare pour une autre version de l'imprimante. Veuillez decouper le modele a nouveau. L'impression a ete annulee. "
+
+#
+"G-code sliced for a newer firmware. Continue?"
+"Le G-code a ete prepare pour une version plus recente du firmware. Continuer?"
+
+#
+"G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+"Le G-code a ete prepare pour une version plus recente du firmware. Veuillez mettre a jour le firmware. L'impression  annulee."
+
+#
+"PINDA:"
+"PINDA:"
+
+#
+"Preheating to cut"
+"Prechauffage pour couper"
+
+#
+"Preheating to eject"
+"Prechauffage pour ejecter"
+
+#
+"Printer nozzle diameter differs from the G-code. Continue?"
+"Diametre de la  buse de l'imprimante different du G-Code. Continuer ?"
+
+#
+"Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+"Diametre de la  buse de l'imprimante different du G-Code. Merci de verifier le parametre dans les reglages. Impression annulee."
+
+#
+"Rename"
+"Renommer"
+
+#
+"Select"
+"Selectionner"
+
+#
+"Sensor info"
+"Info capteur"
+
+#
+"Sheet"
+"Feuille"
+
+#
+"Sound     [assist]"
+"Son       [Assist]"
+
+#
+"Steel sheets"
+"Plaques en acier"
+
+#
+"Z-correct:"
+"Correct-Z:"
+
+#
+"Z-probe nr.    [1]"
+"Sonde-Z num.   [1]"
+
+#
+"Z-probe nr.    [3]"
+"Sonde-Z num.   [3]"

lang/lang_en_it.txt

@@ -15,7 +15,7 @@
 "Rilev. impatto\x0aattivabile solo\x0ain Modalita normale"
 
 #MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-"WARNING:\x0aCrash detection disabled in Stealth mode"
+"WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
 "ATTENZIONE:\x0aRilev. impatto\x0adisattivato in\x0aModalita silenziosa"
 
 #
@@ -256,7 +256,7 @@
 
 #MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
 "Extruder fan:"
-"Ventola estrusore:"
+"Ventola estr:"
 
 #MSG_INFO_EXTRUDER c=15 r=1
 "Extruder info"
@@ -268,7 +268,7 @@
 
 #
 "Fail stats MMU"
-"Statistiche fallimenti MMU"
+"Stat.fall. MMU"
 
 #MSG_FSENS_AUTOLOAD_ON c=17 r=1
 "F. autoload  [on]"
@@ -284,11 +284,11 @@
 
 #
 "Fail stats"
-"Statistiche fallimenti"
+"Stat. fallimenti"
 
 #MSG_FAN_SPEED c=14
 "Fan speed"
-"Velocita ventola"
+"Velocita vent."
 
 #MSG_SELFTEST_FAN c=20
 "Fan test"
@@ -296,7 +296,7 @@
 
 #MSG_FANS_CHECK_ON c=17 r=1
 "Fans check   [on]"
-"Controllo ventole [on]"
+"Control.vent [on]"
 
 #MSG_FANS_CHECK_OFF c=17 r=1
 "Fans check  [off]"
@@ -304,7 +304,7 @@
 
 #MSG_FSENSOR_ON
 "Fil. sensor  [on]"
-"Sensor filam.[On]"
+"Sensor filam.[on]"
 
 #MSG_FSENSOR_NA
 "Fil. sensor [N/A]"
@@ -512,7 +512,7 @@
 
 #MSG_BED_CORRECTION_LEFT c=14 r=1
 "Left side [um]"
-"Lato sinistro [um]"
+"Sinistra  [um]"
 
 #
 "Lin. correction"
@@ -568,7 +568,7 @@
 
 #
 "Measured skew"
-"Disassamento misurato"
+"Deviazione mis"
 
 #
 "MMU fails"
@@ -600,7 +600,7 @@
 
 #
 "MMU power fails"
-"Mancanza corrente MMU"
+"Manc. corr. MMU"
 
 #MSG_STEALTH_MODE_ON
 "Mode    [Stealth]"
@@ -628,15 +628,15 @@
 
 #MSG_MOVE_X
 "Move X"
-"Muovi X"
+"Sposta X"
 
 #MSG_MOVE_Y
 "Move Y"
-"Muovi Y"
+"Sposta Y"
 
 #MSG_MOVE_Z
 "Move Z"
-"Muovi Z"
+"Sposta Z"
 
 #MSG_NO_MOVE
 "No move."
@@ -680,7 +680,7 @@
 
 #MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
 "Old settings found. Default PID, Esteps etc. will be set."
-"Sono state trovate impostazioni vecchie. I valori di default di PID, Esteps etc. saranno impostati"
+"Sono state trovate impostazioni vecchie. Verranno impostati i valori predefiniti di PID, Esteps etc."
 
 #
 "Now remove the test print from steel sheet."
@@ -820,7 +820,7 @@
 
 #MSG_SELFTEST_PRINT_FAN_SPEED c=18
 "Print fan:"
-"Ventola di stampa:"
+"Vent.stam:"
 
 #MSG_CARD_MENU
 "Print from SD"
@@ -972,19 +972,19 @@
 
 #MSG_SORT_NONE c=17 r=1
 "Sort       [none]"
-"Ordina     [none]"
+"Ordina  [nessuno]"
 
 #MSG_SORT_TIME c=17 r=1
 "Sort       [time]"
-"Ordina     [time]"
+"Ordina    [tempo]"
 
 #
 "Severe skew"
-"Disassamento grave"
+"Devia.grave"
 
 #MSG_SORT_ALPHA c=17 r=1
 "Sort   [alphabet]"
-"Ordine  [alfabet]"
+"Ordine [alfabeti]"
 
 #MSG_SORTING c=20 r=1
 "Sorting files"
@@ -996,7 +996,7 @@
 
 #
 "Slight skew"
-"Disassamento lieve"
+"Devia.lieve"
 
 #MSG_SOUND_MUTE c=17 r=1
 "Sound      [mute]"
@@ -1052,11 +1052,11 @@
 
 #MSG_TEMP_CALIBRATION_ON c=20 r=1
 "Temp. cal.   [on]"
-"Calib. temp. [ON]"
+"Calib. temp. [on]"
 
 #MSG_TEMP_CALIBRATION_OFF c=20 r=1
 "Temp. cal.  [off]"
-"Calib. temp.[OFF]"
+"Calib. temp.[off]"
 
 #MSG_CALIBRATION_PINDA_MENU c=17 r=1
 "Temp. calibration"
@@ -1088,7 +1088,7 @@
 
 #
 "Total print time"
-"Tempo di stampa totale"
+"Tempo stampa totale"
 
 #MSG_TUNE
 "Tune"
@@ -1112,7 +1112,7 @@
 
 #MSG_UNLOAD_FILAMENT c=17
 "Unload filament"
-"Scarica filam."
+"Scarica filamento"
 
 #MSG_UNLOADING_FILAMENT c=20 r=1
 "Unloading filament"
@@ -1241,3 +1241,195 @@
 #MSG_OFF
 " [off]"
 "\x00"
+
+#
+"Back"
+"Indietro"
+
+#
+"Checks"
+"Controlli"
+
+#
+"False triggering"
+"Falso innesco"
+
+#
+"FINDA:"
+"\x00"
+
+#
+"Firmware   [none]"
+"Firmware[nessuno]"
+
+#
+"Firmware [strict]"
+"Firmware [esatto]"
+
+#
+"Firmware   [warn]"
+"Firmware [avviso]"
+
+#
+"HW Setup"
+"Installazione HW"
+
+#
+"IR:"
+"\x00"
+
+#
+"Magnets comp.[N/A]"
+"Comp. Magneti[N/A]"
+
+#
+"Magnets comp.[Off]"
+"Comp. Magneti[off]"
+
+#
+"Magnets comp. [On]"
+"Comp. Magneti [on]"
+
+#
+"Mesh         [3x3]"
+"Griglia      [3x3]"
+
+#
+"Mesh         [7x7]"
+"Griglia      [7x7]"
+
+#
+"Mesh bed leveling"
+"Mesh livel. letto"
+
+#
+"MK3S firmware detected on MK3 printer"
+"Firmware MK3S rilevato su stampante MK3"
+
+#
+"MMU Mode [Normal]"
+"Modalita MMU [Normale]"
+
+#
+"MMU Mode[Stealth]"
+"Modalita MMU [Silenziosa]"
+
+#
+"Mode change in progress ..."
+"Cambio modalita in corso ..."
+
+#
+"Model      [none]"
+"Modello [nessuno]"
+
+#
+"Model    [strict]"
+"Modello  [esatto]"
+
+#
+"Model      [warn]"
+"Modello  [avviso]"
+
+#
+"Nozzle d.  [0.25]"
+"Diam.Ugello[0.25]"
+
+#
+"Nozzle d.  [0.40]"
+"Diam.Ugello[0.40]"
+
+#
+"Nozzle d.  [0.60]"
+"Diam.Ugello[0.60]"
+
+#
+"Nozzle     [none]"
+"Ugello  [nessuno]"
+
+#
+"Nozzle   [strict]"
+"Ugello   [esatto]"
+
+#
+"Nozzle     [warn]"
+"Ugello   [avviso]"
+
+#
+"G-code sliced for a different level. Continue?"
+"G-code processato per un livello diverso. Continuare?"
+
+#
+"G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+"G-code processato per un livello diverso. Per favore esegui nuovamente lo slice del modello. Stampa annullata."
+
+#
+"G-code sliced for a different printer type. Continue?"
+"G-code processato per una stampante diversa. Continuare?"
+
+#
+"G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+"G-code processato per una stampante diversa. Per favore esegui nuovamente lo slice del modello. Stampa annullata."
+
+#
+"G-code sliced for a newer firmware. Continue?"
+"G-code processato per un firmware piu recente. Continuare?"
+
+#
+"G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+"G-code processato per un firmware piu recente. Per favore aggiorna il firmware. Stampa annullata."
+
+#
+"PINDA:"
+"\x00"
+
+#
+"Preheating to cut"
+"Preriscaldamento per taglio"
+
+#
+"Preheating to eject"
+"Preriscaldamento per espulsione"
+
+#
+"Printer nozzle diameter differs from the G-code. Continue?"
+"Diametro ugello diverso da G-Code. Continuare?"
+
+#
+"Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+"Diametro ugello diverso dal G-Code. Controlla il valore nelle impostazioni. Stampa annullata."
+
+#
+"Rename"
+"Rinomina"
+
+#
+"Select"
+"Seleziona"
+
+#
+"Sensor info"
+"Info Sensore"
+
+#
+"Sheet"
+"Piano"
+
+#
+"Sound     [assist]"
+"Suono  [assistito]"
+
+#
+"Steel sheets"
+"Piani d'acciaio"
+
+#
+"Z-correct:"
+"Correzione-Z:"
+
+#
+"Z-probe nr.    [1]"
+"Z-probe nr.    [1]"
+
+#
+"Z-probe nr.    [3]"
+"Z-probe nr.    [3]"

lang/lang_en_pl.txt

@@ -8,7 +8,7 @@
 
 #MSG_MEASURED_OFFSET
 "[0;0] point offset"
-"[0;0] przesuniecie punktu"
+"[0;0] przesun.punktu"
 
 #MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
 "Crash detection can\x0abe turned on only in\x0aNormal mode"
@@ -24,7 +24,7 @@
 
 #MSG_BABYSTEPPING_Z c=15
 "Adjusting Z:"
-"Dostrajanie Z:"
+"Ustawianie Z:"
 
 #MSG_SELFTEST_CHECK_ALLCORRECT c=20
 "All correct      "
@@ -44,7 +44,7 @@
 
 #MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
 "Are left and right Z~carriages all up?"
-"Obydwa konce osi dojechaly do gornych ogranicznikow?"
+"Obydwa konce osi sa na szczycie?"
 
 #MSG_AUTO_DEPLETE_ON c=17 r=1
 "SpoolJoin    [on]"
@@ -216,7 +216,7 @@
 
 #MSG_EXTRUDER_CORRECTION c=10
 "E-correct:"
-"Korekcja E:"
+"Korekcja-E:"
 
 #MSG_EJECT_FILAMENT c=17 r=1
 "Eject filament"
@@ -256,7 +256,7 @@
 
 #MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
 "Extruder fan:"
-"Went. ekstrudera:"
+"Went. ekstr:"
 
 #MSG_INFO_EXTRUDER c=15 r=1
 "Extruder info"
@@ -688,7 +688,7 @@
 
 #
 "Nozzle FAN"
-"Went. hotendu"
+"Went. Hotend"
 
 #MSG_PAUSE_PRINT
 "Pause print"
@@ -820,7 +820,7 @@
 
 #MSG_SELFTEST_PRINT_FAN_SPEED c=18
 "Print fan:"
-"Went. wydruku:"
+"Went.wydr:"
 
 #MSG_CARD_MENU
 "Print from SD"
@@ -844,7 +844,7 @@
 
 #
 "Print FAN"
-"Went. wydruku"
+"Went.wydr"
 
 #MSG_PRUSA3D
 "prusa3d.com"
@@ -972,19 +972,19 @@
 
 #MSG_SORT_NONE c=17 r=1
 "Sort       [none]"
-"Sortuj     [brak]"
+"Sortowanie [brak]"
 
 #MSG_SORT_TIME c=17 r=1
 "Sort       [time]"
-"Sortuj     [czas]"
+"Sortowanie [czas]"
 
 #
 "Severe skew"
-"Znaczny skos"
+"ZnacznySkos"
 
 #MSG_SORT_ALPHA c=17 r=1
 "Sort   [alphabet]"
-"Sortuj  [alfabet]"
+"Sortowan[alfabet]"
 
 #MSG_SORTING c=20 r=1
 "Sorting files"
@@ -1032,7 +1032,7 @@
 
 #MSG_STOP_PRINT
 "Stop print"
-"Zatrzymac druk"
+"Przerwanie druku"
 
 #MSG_STOPPED
 "STOPPED. "
@@ -1052,7 +1052,7 @@
 
 #MSG_TEMP_CALIBRATION_ON c=20 r=1
 "Temp. cal.   [on]"
-"Kalibr. temp.[wl]"
+"Kalibr.temp. [wl]"
 
 #MSG_TEMP_CALIBRATION_OFF c=20 r=1
 "Temp. cal.  [off]"
@@ -1200,7 +1200,7 @@
 
 #
 "X-correct:"
-"Korekcja X:"
+"Korekcja-X:"
 
 #MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
 "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
@@ -1236,8 +1236,200 @@
 
 #
 "Y-correct:"
-"Korekcja Y:"
+"Korekcja-Y:"
 
 #MSG_OFF
 " [off]"
+" [wyl]"
+
+#
+"Back"
+"Wstecz"
+
+#
+"Checks"
+"Testy"
+
+#
+"False triggering"
+"Falszywy alarm"
+
+#
+"FINDA:"
 "\x00"
+
+#
+"Firmware   [none]"
+"Firmware   [brak]"
+
+#
+"Firmware [strict]"
+"Firmware [restr.]"
+
+#
+"Firmware   [warn]"
+"Firmware[ostrzez]"
+
+#
+"HW Setup"
+"Ustawienia HW"
+
+#
+"IR:"
+"\x00"
+
+#
+"Magnets comp.[N/A]"
+"Kor. magnesow [nd]"
+
+#
+"Magnets comp.[Off]"
+"Kor. magnesow[wyl]"
+
+#
+"Magnets comp. [On]"
+"Kor. magnesow [wl]"
+
+#
+"Mesh         [3x3]"
+"Siatka       [3x3]"
+
+#
+"Mesh         [7x7]"
+"Siatka       [7x7]"
+
+#
+"Mesh bed leveling"
+"Poziomowanie wg siatki"
+
+#
+"MK3S firmware detected on MK3 printer"
+"Wykryto firmware MK3S w drukarce MK3"
+
+#
+"MMU Mode [Normal]"
+"Tryb MMU[Normaln]"
+
+#
+"MMU Mode[Stealth]"
+"Tryb MMU[Stealth]"
+
+#
+"Mode change in progress ..."
+"Trwa zmiana trybu..."
+
+#
+"Model      [none]"
+"Model      [brak]"
+
+#
+"Model    [strict]"
+"Model [restrykc.]"
+
+#
+"Model      [warn]"
+"Model  [ostrzez.]"
+
+#
+"Nozzle d.  [0.25]"
+"Sr. dyszy  [0,25]"
+
+#
+"Nozzle d.  [0.40]"
+"Sr. dyszy  [0,40]"
+
+#
+"Nozzle d.  [0.60]"
+"Sr. dyszy  [0,60]"
+
+#
+"Nozzle     [none]"
+"Dysza      [brak]"
+
+#
+"Nozzle   [strict]"
+"Dysza [restrykc.]"
+
+#
+"Nozzle     [warn]"
+"Dysza  [ostrzez.]"
+
+#
+"G-code sliced for a different level. Continue?"
+"\x00"
+
+#
+"G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+"G-code pociety na innym poziomie. Potnij model ponownie. Druk anulowany."
+
+#
+"G-code sliced for a different printer type. Continue?"
+"G-code pociety dla innej drukarki. Kontynuowac?"
+
+#
+"G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+"G-code pociety dla drukarki innego typu. Potnij model ponownie. Druk anulowany."
+
+#
+"G-code sliced for a newer firmware. Continue?"
+"G-code pociety dla nowszego firmware. Kontynuowac?"
+
+#
+"G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+"G-code pociety dla nowszego firmware. Zaktualizuj firmware. Druk anulowany."
+
+#
+"PINDA:"
+"\x00"
+
+#
+"Preheating to cut"
+"Nagrzewanie do obciecia"
+
+#
+"Preheating to eject"
+"Nagrzewanie do wysuniecia"
+
+#
+"Printer nozzle diameter differs from the G-code. Continue?"
+"Srednica dyszy drukarki rozni sie od tej w G-code. Kontynuowac?"
+
+#
+"Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+"Srednica dyszy rozni sie od tej w G-code. Sprawdz ustawienia. Druk anulowany."
+
+#
+"Rename"
+"Zmien nazwe"
+
+#
+"Select"
+"Wybierz"
+
+#
+"Sensor info"
+"Info o sensorach"
+
+#
+"Sheet"
+"Plyta"
+
+#
+"Sound     [assist]"
+"Dzwiek    [asyst.]"
+
+#
+"Steel sheets"
+"Plyty stalowe"
+
+#
+"Z-correct:"
+"Korekcja-Z:"
+
+#
+"Z-probe nr.    [1]"
+"Pomiar-Z       [1]"
+
+#
+"Z-probe nr.    [3]"
+"Pomiar-Z       [3]"

lang/po/Firmware.pot

@@ -7,8 +7,8 @@ msgstr ""
 "Content-Transfer-Encoding: 8bit\n"
 "Language: en\n"
 "Project-Id-Version: Prusa-Firmware\n"
-"POT-Creation-Date: čt 7. úno 2019 14:41:39\n"
-"PO-Revision-Date: čt 7. úno 2019 14:41:39\n"
+"POT-Creation-Date: Wed Sep 4 16:13:32 CEST 2019\n"
+"PO-Revision-Date: Wed Sep 4 16:13:32 CEST 2019\n"
 "Language-Team: \n"
 "X-Generator: Poedit 2.0.7\n"
 "X-Poedit-SourceCharset: UTF-8\n"
@@ -21,72 +21,72 @@ msgid " of 4"
 msgstr ""
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr ""
 
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3027
 msgid "[0;0] point offset"
 msgstr ""
 
 # MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
-#: ultralcd.cpp:4219
-msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
+#: 
+msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
 msgstr ""
 
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-#: ultralcd.cpp:4231
-msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
+#: 
+msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2290
 msgid ">Cancel"
 msgstr ""
 
-# MSG_BABYSTEPPING_Z c=20
-#: ultralcd.cpp:3043
-msgid "Adjusting Z"
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3147
+msgid "Adjusting Z:"
 msgstr ""
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr ""
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1974
 msgid "Ambient"
 msgstr ""
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2576
 msgid "and press the knob"
 msgstr ""
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3445
 msgid "Are left and right Z~carriages all up?"
 msgstr ""
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5114
 msgid "SpoolJoin    [on]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5110
 msgid "SpoolJoin   [N/A]"
 msgstr ""
 
-#  MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+# MSG_AUTO_DEPLETE_OFF c=17 r=1
+#: ultralcd.cpp:5118
 msgid "SpoolJoin   [off]"
 msgstr ""
 
@@ -96,32 +96,32 @@ msgid "Auto home"
 msgstr ""
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6736
 msgid "AutoLoad filament"
 msgstr ""
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4378
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr ""
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2771
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr ""
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr ""
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr ""
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr ""
 
@@ -136,7 +136,7 @@ msgid "Bed Heating"
 msgstr ""
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5682
 msgid "Bed level correct"
 msgstr ""
 
@@ -145,38 +145,28 @@ msgstr ""
 msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
 msgstr ""
 
-# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
-#: Marlin_main.cpp:4508
-msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
-msgstr ""
-
-# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
-#: Marlin_main.cpp:4512
-msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
-msgstr ""
-
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr ""
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2002
 msgid "Belt status"
 msgstr ""
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr ""
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
 msgstr ""
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5671
 msgid "Calibrate XYZ"
 msgstr ""
 
@@ -186,12 +176,12 @@ msgid "Calibrate Z"
 msgstr ""
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4570
 msgid "Calibrate"
 msgstr ""
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr ""
 
@@ -201,37 +191,32 @@ msgid "Calibrating Z"
 msgstr ""
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr ""
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:813
 msgid "Calibration done"
 msgstr ""
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Cancel"
 msgstr ""
 
-# MSG_SD_INSERTED
-#: 
-msgid "Card inserted"
-msgstr ""
-
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr ""
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2676
 msgid "Color not correct"
 msgstr ""
 
@@ -241,7 +226,7 @@ msgid "Cooldown"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4503
 msgid "Copy selected language?"
 msgstr ""
 
@@ -266,27 +251,27 @@ msgid "Crash detected."
 msgstr ""
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:600
 msgid "Crash detected. Resume print?"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Crash"
 msgstr ""
 
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5823
 msgid "Current"
 msgstr ""
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2102
 msgid "Date:"
 msgstr ""
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5568
 msgid "Disable steppers"
 msgstr ""
 
@@ -296,77 +281,52 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr ""
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4984
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr ""
 
-# MSG_EXTRUDER_CORRECTION c=9
-#: ultralcd.cpp:4889
-msgid "E-correct"
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5048
+msgid "E-correct:"
 msgstr ""
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr ""
 
-# MSG_EJECT_FILAMENT1 c=17 r=1
-#: ultralcd.cpp:5603
-msgid "Eject filament 1"
-msgstr ""
-
-# MSG_EJECT_FILAMENT2 c=17 r=1
-#: ultralcd.cpp:5604
-msgid "Eject filament 2"
-msgstr ""
-
-# MSG_EJECT_FILAMENT3 c=17 r=1
-#: ultralcd.cpp:5605
-msgid "Eject filament 3"
-msgstr ""
-
-# MSG_EJECT_FILAMENT4 c=17 r=1
-#: ultralcd.cpp:5606
-msgid "Eject filament 4"
-msgstr ""
-
-# MSG_EJECT_FILAMENT5 c=17 r=1
-#: ultralcd.cpp:5607
-msgid "Eject filament 5"
-msgstr ""
-
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Eject"
 msgstr ""
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1434
 msgid "Ejecting filament"
 msgstr ""
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr ""
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr ""
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr ""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr ""
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4391
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr ""
 
@@ -375,38 +335,13 @@ msgstr ""
 msgid "ERROR:"
 msgstr ""
 
-# 
-#: Marlin_main.cpp:1006
-msgid "External SPI flash W25X20CL not responding."
-msgstr ""
-
-# 
-#: ultralcd.cpp:5633
-msgid "Extruder 1"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5634
-msgid "Extruder 2"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5635
-msgid "Extruder 3"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5636
-msgid "Extruder 4"
-msgstr ""
-
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr ""
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2133
 msgid "Extruder info"
 msgstr ""
 
@@ -416,12 +351,12 @@ msgid "Extruder"
 msgstr ""
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
 msgstr ""
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5082
 msgid "F. autoload  [on]"
 msgstr ""
 
@@ -431,12 +366,12 @@ msgid "F. autoload [N/A]"
 msgstr ""
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5084
 msgid "F. autoload [off]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr ""
 
@@ -446,17 +381,17 @@ msgid "Fan speed"
 msgstr ""
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr ""
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5577
 msgid "Fans check   [on]"
 msgstr ""
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5579
 msgid "Fans check  [off]"
 msgstr ""
 
@@ -465,13 +400,8 @@ msgstr ""
 msgid "Fil. sensor  [on]"
 msgstr ""
 
-# MSG_RESPONSE_POOR c=20 r=2
-#: Marlin_main.cpp:3146
-msgid "Fil. sensor response is poor, disable it?"
-msgstr ""
-
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5062
 msgid "Fil. sensor [N/A]"
 msgstr ""
 
@@ -481,7 +411,7 @@ msgid "Fil. sensor [off]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Filam. runouts"
 msgstr ""
 
@@ -491,32 +421,27 @@ msgid "Filament extruding & with correct color?"
 msgstr ""
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2672
 msgid "Filament not loaded"
 msgstr ""
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr ""
 
-# MSG_SELFTEST_FILAMENT_SENSOR c=18
-#: ultralcd.cpp:7477
-msgid "Filament sensor:"
-msgstr ""
-
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2841
 msgid "Filament used"
 msgstr ""
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2841
 msgid "Print time"
 msgstr ""
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr ""
 
@@ -526,52 +451,52 @@ msgid "Finishing movements"
 msgstr ""
 
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr ""
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4896
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr ""
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr ""
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr ""
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2095
 msgid "forum.prusa3d.com"
 msgstr ""
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr ""
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3220
 msgid "Front side[um]"
 msgstr ""
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr ""
 
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr ""
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8468
 msgid "Heating disabled by safety timer."
 msgstr ""
 
@@ -586,67 +511,62 @@ msgid "Heating"
 msgstr ""
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4875
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr ""
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2096
 msgid "howto.prusa3d.com"
 msgstr ""
 
-# 
-#: ultralcd.cpp:6087
-msgid "Change extruder"
-msgstr ""
-
 # MSG_FILAMENTCHANGE
 #: messages.c:37
 msgid "Change filament"
 msgstr ""
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2587
 msgid "Change success!"
 msgstr ""
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2664
 msgid "Changed correctly?"
 msgstr ""
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr ""
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr ""
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr ""
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr ""
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr ""
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr ""
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr ""
 
@@ -666,112 +586,82 @@ msgid "Filament"
 msgstr ""
 
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4905
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr ""
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4913
 msgid "I will run z calibration now."
 msgstr ""
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4978
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr ""
 
-# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
-#: mesh_bed_calibration.cpp:2481
-msgid "Improving bed calibration point"
-msgstr ""
-
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr ""
 
-# MSG_FILAMENT_LOADING_T0 c=20 r=4
-#: messages.c:33
-msgid "Insert filament into extruder 1. Click when done."
-msgstr ""
-
-# MSG_FILAMENT_LOADING_T1 c=20 r=4
-#: messages.c:34
-msgid "Insert filament into extruder 2. Click when done."
-msgstr ""
-
-# MSG_FILAMENT_LOADING_T2 c=20 r=4
-#: messages.c:35
-msgid "Insert filament into extruder 3. Click when done."
-msgstr ""
-
-# MSG_FILAMENT_LOADING_T3 c=20 r=4
-#: messages.c:36
-msgid "Insert filament into extruder 4. Click when done."
-msgstr ""
-
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:4938
 msgid "Is filament 1 loaded?"
 msgstr ""
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2572
 msgid "Insert filament"
 msgstr ""
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4941
 msgid "Is filament loaded?"
 msgstr ""
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4972
 msgid "Is it PLA filament?"
 msgstr ""
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4704
 msgid "Is PLA filament loaded?"
 msgstr ""
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr ""
 
-# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
-#: mesh_bed_calibration.cpp:2223
-msgid "Iteration "
-msgstr ""
-
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1840
 msgid "Last print failures"
 msgstr ""
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1823
 msgid "Last print"
 msgstr ""
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2970
 msgid "Left"
 msgstr ""
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3218
 msgid "Left side [um]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5594
 msgid "Lin. correction"
 msgstr ""
 
@@ -786,7 +676,7 @@ msgid "Load filament"
 msgstr ""
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2612
 msgid "Loading color"
 msgstr ""
 
@@ -796,92 +686,92 @@ msgid "Loading filament"
 msgstr ""
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr ""
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6719
 msgid "Load to nozzle"
 msgstr ""
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr ""
 
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr ""
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr ""
 
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5677
 msgid "Mesh Bed Leveling"
 msgstr ""
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr ""
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr ""
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3005
 msgid "Measured skew"
 msgstr ""
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU fails"
 msgstr ""
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1613
 msgid "MMU load failed     "
 msgstr ""
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU load fails"
 msgstr ""
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr ""
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr ""
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr ""
 
 # 
-#: mmu.cpp:635
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr ""
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "MMU power fails"
 msgstr ""
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr ""
 
@@ -891,62 +781,62 @@ msgid "Mode [auto power]"
 msgstr ""
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2108
 msgid "MMU2 connected"
 msgstr ""
 
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr ""
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5566
 msgid "Move axis"
 msgstr ""
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4294
 msgid "Move X"
 msgstr ""
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4295
 msgid "Move Y"
 msgstr ""
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4296
 msgid "Move Z"
 msgstr ""
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5291
 msgid "No move."
 msgstr ""
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6686
 msgid "No SD card"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2976
 msgid "N/A"
 msgstr ""
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr ""
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr ""
 
@@ -955,78 +845,73 @@ msgstr ""
 msgid "New firmware version available:"
 msgstr ""
 
-# 
-#: 
-msgid "No "
-msgstr ""
-
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr ""
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4977
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr ""
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4921
 msgid "Now I will preheat nozzle for PLA."
 msgstr ""
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr ""
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1519
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr ""
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4912
 msgid "Now remove the test print from steel sheet."
 msgstr ""
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:1782
 msgid "Nozzle FAN"
 msgstr ""
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6649
 msgid "Pause print"
 msgstr ""
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1598
 msgid "PID cal.           "
 msgstr ""
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1604
 msgid "PID cal. finished"
 msgstr ""
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5683
 msgid "PID calibration"
 msgstr ""
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:843
 msgid "PINDA Heating"
 msgstr ""
 
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr ""
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4986
 msgid "Please clean heatbed and then press the knob."
 msgstr ""
 
@@ -1036,92 +921,92 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr ""
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr ""
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr ""
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4808
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr ""
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4709
 msgid "Please load PLA filament first."
 msgstr ""
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3063
 msgid "Please open idler and remove filament manually."
 msgstr ""
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr ""
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4803
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr ""
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr ""
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1440
 msgid "Please remove filament and then press the knob."
 msgstr ""
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr ""
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4354
 msgid "Please run XYZ calibration first."
 msgstr ""
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1359
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr ""
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4911
 msgid "Please remove shipping helpers first."
 msgstr ""
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr ""
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6636
 msgid "Preheat"
 msgstr ""
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr ""
 
@@ -1131,32 +1016,32 @@ msgid "Please upgrade."
 msgstr ""
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10365
 msgid "Press knob to preheat nozzle and continue."
 msgstr ""
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Power failures"
 msgstr ""
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2276
 msgid "Preheating to load"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2280
 msgid "Preheating to unload"
 msgstr ""
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr ""
 
@@ -1166,17 +1051,17 @@ msgid "Print from SD"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2206
 msgid "Press the knob"
 msgstr ""
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1061
 msgid "Print paused"
 msgstr ""
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr ""
 
@@ -1186,37 +1071,27 @@ msgid "Printer has not been calibrated yet. Please follow the manual, chapter Fi
 msgstr ""
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1784
 msgid "Print FAN"
 msgstr ""
 
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK2.5 ready."
-msgstr ""
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK3 ready."
-msgstr ""
-
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2094
 msgid "prusa3d.com"
 msgstr ""
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3221
 msgid "Rear side [um]"
 msgstr ""
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9765
 msgid "Recovering print    "
 msgstr ""
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr ""
 
@@ -1225,63 +1100,58 @@ msgstr ""
 msgid "Prusa i3 MK3S OK."
 msgstr ""
 
-# 
-#: 
-msgid "Prusa i3 MK2 ready."
-msgstr ""
-
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5688
 msgid "Reset XYZ calibr."
 msgstr ""
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3222
 msgid "Reset"
 msgstr ""
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6656
 msgid "Resume print"
 msgstr ""
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr ""
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3219
 msgid "Right side[um]"
 msgstr ""
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5606
 msgid "RPi port     [on]"
 msgstr ""
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5604
 msgid "RPi port    [off]"
 msgstr ""
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4726
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr ""
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5236
 msgid "SD card  [normal]"
 msgstr ""
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5234
 msgid "SD card [flshAir]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2971
 msgid "Right"
 msgstr ""
 
@@ -1291,217 +1161,207 @@ msgid "Searching bed calibration point"
 msgstr ""
 
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5613
 msgid "Select language"
 msgstr ""
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr ""
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr ""
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5664
 msgid "Selftest         "
 msgstr ""
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr ""
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr ""
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1551
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr ""
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4959
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr ""
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Select PLA filament:"
 msgstr ""
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3230
 msgid "Set temperature:"
 msgstr ""
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr ""
 
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5685
 msgid "Show end stops"
 msgstr ""
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:3941
 msgid "Sensor state"
 msgstr ""
 
-# 
-#: 
-msgid "Sensors info"
-msgstr ""
-
-# 
-#: 
-msgid "Show pinda state"
-msgstr ""
-
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr ""
 
 # MSG_SORT_NONE c=17 r=1
-#: ultralcd.cpp:5043
-msgid "Sort:      [none]"
+#: ultralcd.cpp:5246
+msgid "Sort       [none]"
 msgstr ""
 
 # MSG_SORT_TIME c=17 r=1
-#: ultralcd.cpp:5041
-msgid "Sort:      [time]"
+#: ultralcd.cpp:5244
+msgid "Sort       [time]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3008
 msgid "Severe skew"
 msgstr ""
 
 # MSG_SORT_ALPHA c=17 r=1
-#: ultralcd.cpp:5042
-msgid "Sort:  [alphabet]"
+#: ultralcd.cpp:5245
+msgid "Sort   [alphabet]"
 msgstr ""
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr ""
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3007
 msgid "Slight skew"
 msgstr ""
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#: 
 msgid "Sound      [mute]"
 msgstr ""
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4870
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr ""
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr ""
 
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr ""
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr ""
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr ""
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4367
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr ""
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr ""
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr ""
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr ""
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr ""
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr ""
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr ""
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5600
 msgid "Temp. cal.   [on]"
 msgstr ""
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5598
 msgid "Temp. cal.  [off]"
 msgstr ""
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5694
 msgid "Temp. calibration"
 msgstr ""
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3867
 msgid "Temperature calibration failed"
 msgstr ""
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr ""
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5564
 msgid "Temperature"
 msgstr ""
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2140
 msgid "Temperatures"
 msgstr ""
 
@@ -1511,127 +1371,122 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr ""
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2863
 msgid "Total filament"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2863
 msgid "Total print time"
 msgstr ""
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6633
 msgid "Tune"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Unload"
 msgstr ""
 
 # 
-#: ultralcd.cpp:5617
-msgid "Unload all"
-msgstr ""
-
-# 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "Total failures"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2213
 msgid "to load filament"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2217
 msgid "to unload filament"
 msgstr ""
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr ""
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr ""
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1824
 msgid "Total"
 msgstr ""
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5822
 msgid "Used during print"
 msgstr ""
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2143
 msgid "Voltages"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2116
 msgid "unknown"
 msgstr ""
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5262
 msgid "Wait for user..."
 msgstr ""
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3374
 msgid "Waiting for nozzle and bed cooling"
 msgstr ""
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3338
 msgid "Waiting for PINDA probe cooling"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4782
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr ""
 
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1511
 msgid "Warning: both printer type and motherboard type changed."
 msgstr ""
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1503
 msgid "Warning: motherboard type changed."
 msgstr ""
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1507
 msgid "Warning: printer type changed."
 msgstr ""
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3053
 msgid "Was filament unload successful?"
 msgstr ""
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr ""
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5661
 msgid "Wizard"
 msgstr ""
 
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2132
 msgid "XYZ cal. details"
 msgstr ""
 
@@ -1641,107 +1496,312 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr ""
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr ""
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr ""
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3838
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr ""
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4885
-msgid "X-correct"
+#: ultralcd.cpp:5044
+msgid "X-correct:"
 msgstr ""
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3832
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr ""
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr ""
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3819
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr ""
 
-# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
-#: ultralcd.cpp:3699
-msgid "XYZ calibration compromised. Left front calibration point not reachable."
-msgstr ""
-
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6080
 msgid "Load all"
 msgstr ""
 
-# MSG_LOAD_FILAMENT_1 c=17
-#: ultralcd.cpp:5576
-msgid "Load filament 1"
-msgstr ""
-
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3798
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr ""
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr ""
 
 # 
-#: ultralcd.cpp:3687
-msgid "XYZ calibration failed. Left front calibration point not reachable."
+#: ultralcd.cpp:3807
+msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr ""
 
-# MSG_LOAD_FILAMENT_2 c=17
-#: ultralcd.cpp:5577
-msgid "Load filament 2"
+# 
+#: ultralcd.cpp:2968
+msgid "Y distance from min"
 msgstr ""
 
 # 
-#: ultralcd.cpp:3684
-msgid "XYZ calibration failed. Right front calibration point not reachable."
+#: ultralcd.cpp:5045
+msgid "Y-correct:"
 msgstr ""
 
-# MSG_LOAD_FILAMENT_3 c=17
-#: ultralcd.cpp:5578
-msgid "Load filament 3"
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
 msgstr ""
 
 # 
-#: ultralcd.cpp:2859
-msgid "Y distance from min"
+#: messages.c:57
+msgid "Back"
 msgstr ""
 
 # 
-#: ultralcd.cpp:4886
-msgid "Y-correct"
+#: ultralcd.cpp:5553
+msgid "Checks"
 msgstr ""
 
-# MSG_LOAD_FILAMENT_4 c=17
-#: ultralcd.cpp:5579
-msgid "Load filament 4"
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr ""
+
+# 
+#: ultralcd.cpp:3946
+msgid "FINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5459
+msgid "Firmware   [none]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5465
+msgid "Firmware [strict]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5462
+msgid "Firmware   [warn]"
+msgstr ""
+
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr ""
+
+# 
+#: ultralcd.cpp:3950
+msgid "IR:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5591
+msgid "Mesh bed leveling"
+msgstr ""
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5220
+msgid "MMU Mode [Normal]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5221
+msgid "MMU Mode[Stealth]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:4427
+msgid "Mode change in progress ..."
+msgstr ""
+
+# 
+#: ultralcd.cpp:5420
+msgid "Model      [none]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5426
+msgid "Model    [strict]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5423
+msgid "Model      [warn]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5381
+msgid "Nozzle d.  [0.25]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5384
+msgid "Nozzle d.  [0.40]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5387
+msgid "Nozzle d.  [0.60]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5335
+msgid "Nozzle     [none]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5341
+msgid "Nozzle   [strict]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5338
+msgid "Nozzle     [warn]"
+msgstr ""
+
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
 msgstr ""
 
-# MSG_LOAD_FILAMENT_5 c=17
-#: ultralcd.cpp:5582
-msgid "Load filament 5"
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:3942
+msgid "PINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2286
+msgid "Preheating to cut"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2283
+msgid "Preheating to eject"
+msgstr ""
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:6597
+msgid "Rename"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6593
+msgid "Select"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2134
+msgid "Sensor info"
+msgstr ""
+
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr ""
+
+# 
+#: 
+msgid "Sound     [assist]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5046
+msgid "Z-correct:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
 msgstr ""
 

lang/po/Firmware_cs.po

@@ -7,8 +7,8 @@ msgstr ""
 "Content-Transfer-Encoding: 8bit\n"
 "Language: cs\n"
 "Project-Id-Version: Prusa-Firmware\n"
-"POT-Creation-Date: čt 7. úno 2019 14:43:00\n"
-"PO-Revision-Date: čt 7. úno 2019 14:43:00\n"
+"POT-Creation-Date: Wed Sep 4 16:13:39 CEST 2019\n"
+"PO-Revision-Date: Wed Sep 4 16:13:39 CEST 2019\n"
 "Language-Team: \n"
 "X-Generator: Poedit 2.0.7\n"
 "X-Poedit-SourceCharset: UTF-8\n"
@@ -21,72 +21,72 @@ msgid " of 4"
 msgstr " z 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " z 9"
 
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3027
 msgid "[0;0] point offset"
 msgstr "[0;0] odsazeni bodu"
 
 # MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
-#: ultralcd.cpp:4219
-msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
-msgstr "\x1b[2JCrash detekce muze\x1b[1;0Hbyt zapnuta pouze v\x1b[2;0HNormal modu"
+#: 
+msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
+msgstr "Crash detekce muze\x0abyt zapnuta pouze v\x0aNormal modu"
 
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-#: ultralcd.cpp:4231
-msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
-msgstr "\x1b[2JPOZOR:\x1b[1;0HCrash detekce\x1b[2;0Hdeaktivovana ve\x1b[3;0HStealth modu"
+#: 
+msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
+msgstr "POZOR:\x0aCrash detekce\x0adeaktivovana ve\x0aStealth modu"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2290
 msgid ">Cancel"
-msgstr ""
+msgstr ">Zrusit"
 
-# MSG_BABYSTEPPING_Z c=20
-#: ultralcd.cpp:3043
-msgid "Adjusting Z"
-msgstr "Dostavovani Z"
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3147
+msgid "Adjusting Z:"
+msgstr "Dostavovani Z:"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Vse OK "
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Vse je hotovo."
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1974
 msgid "Ambient"
-msgstr ""
+msgstr "Okoli"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2576
 msgid "and press the knob"
 msgstr "a stisknete tlacitko"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3445
 msgid "Are left and right Z~carriages all up?"
 msgstr "Dojely oba Z voziky k~hornimu dorazu?"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5114
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin   [zap]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5110
 msgid "SpoolJoin   [N/A]"
-msgstr "SpoolJoin   [N/A]"
+msgstr ""
 
-#  MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+# MSG_AUTO_DEPLETE_OFF c=17 r=1
+#: ultralcd.cpp:5118
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [vyp]"
 
@@ -96,32 +96,32 @@ msgid "Auto home"
 msgstr ""
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6736
 msgid "AutoLoad filament"
 msgstr "AutoZavedeni fil."
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4378
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Automaticke zavadeni filamentu je dostupne pouze pri zapnutem filament senzoru..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2771
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Automaticke zavadeni filamentu aktivni, stisknete tlacitko a vlozte filament..."
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Delka osy"
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Osa"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Podlozka / Topeni"
 
@@ -136,7 +136,7 @@ msgid "Bed Heating"
 msgstr "Zahrivani bed"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5682
 msgid "Bed level correct"
 msgstr "Korekce podlozky"
 
@@ -145,38 +145,28 @@ msgstr "Korekce podlozky"
 msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
 msgstr "Kalibrace Z selhala. Sensor nesepnul. Znecistena tryska? Cekam na reset."
 
-# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
-#: Marlin_main.cpp:4508
-msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
-msgstr "Kalibrace Z selhala. Sensor je odpojeny nebo preruseny kabel. Cekam na reset."
-
-# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
-#: Marlin_main.cpp:4512
-msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
-msgstr "Kalibrace Z selhala. Sensor sepnul prilis vysoko. Cekam na reset."
-
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Podlozka"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2002
 msgid "Belt status"
 msgstr "Stav remenu"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Detekovan vypadek proudu.Obnovit tisk?"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
-msgstr ""
+msgstr "Kalibruji vychozi poz."
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5671
 msgid "Calibrate XYZ"
 msgstr "Kalibrace XYZ"
 
@@ -186,12 +176,12 @@ msgid "Calibrate Z"
 msgstr "Kalibrovat Z"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4570
 msgid "Calibrate"
 msgstr "Zkalibrovat"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibrace XYZ. Otacenim tlacitka posunte Z osu az k~hornimu dorazu. Potvrdte tlacitkem."
 
@@ -201,37 +191,32 @@ msgid "Calibrating Z"
 msgstr "Kalibruji Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibrace Z. Otacenim tlacitka posunte Z osu az k~hornimu dorazu. Potvrdte tlacitkem."
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:813
 msgid "Calibration done"
 msgstr "Kalibrace OK"
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Kalibrace"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Cancel"
 msgstr "Zrusit"
 
-# MSG_SD_INSERTED
-#: 
-msgid "Card inserted"
-msgstr "Karta vlozena"
-
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Karta vyjmuta"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2676
 msgid "Color not correct"
 msgstr "Barva neni cista"
 
@@ -241,7 +226,7 @@ msgid "Cooldown"
 msgstr "Zchladit"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4503
 msgid "Copy selected language?"
 msgstr "Kopirovat vybrany jazyk?"
 
@@ -253,7 +238,7 @@ msgstr "Crash det.  [zap]"
 # MSG_CRASHDETECT_NA
 #: messages.c:25
 msgid "Crash det.  [N/A]"
-msgstr "Crash det.  [N/A]"
+msgstr ""
 
 # MSG_CRASHDETECT_OFF
 #: messages.c:26
@@ -266,27 +251,27 @@ msgid "Crash detected."
 msgstr "Detekovan naraz."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:600
 msgid "Crash detected. Resume print?"
 msgstr "Detekovan naraz. Obnovit tisk?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Crash"
-msgstr ""
+msgstr "Naraz"
 
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5823
 msgid "Current"
 msgstr "Pouze aktualni"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2102
 msgid "Date:"
 msgstr "Datum:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5568
 msgid "Disable steppers"
 msgstr "Vypnout motory"
 
@@ -296,77 +281,52 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Neni zkalibrovana vzdalenost trysky od tiskove podlozky. Postupujte prosim podle manualu, kapitola Zaciname, odstavec Nastaveni prvni vrstvy."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4984
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Chcete opakovat posledni krok a pozmenit vzdalenost mezi tryskou a podlozkou?"
 
-# MSG_EXTRUDER_CORRECTION c=9
-#: ultralcd.cpp:4889
-msgid "E-correct"
-msgstr "Korekce E"
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5048
+msgid "E-correct:"
+msgstr "Korekce E:"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Vysunout filament"
 
-# MSG_EJECT_FILAMENT1 c=17 r=1
-#: ultralcd.cpp:5603
-msgid "Eject filament 1"
-msgstr "Vysunout filament 1"
-
-# MSG_EJECT_FILAMENT2 c=17 r=1
-#: ultralcd.cpp:5604
-msgid "Eject filament 2"
-msgstr "Vysunout filament 2"
-
-# MSG_EJECT_FILAMENT3 c=17 r=1
-#: ultralcd.cpp:5605
-msgid "Eject filament 3"
-msgstr "Vysunout filament 3"
-
-# MSG_EJECT_FILAMENT4 c=17 r=1
-#: ultralcd.cpp:5606
-msgid "Eject filament 4"
-msgstr "Vysunout filament 4"
-
-# MSG_EJECT_FILAMENT5 c=17 r=1
-#: ultralcd.cpp:5607
-msgid "Eject filament 5"
-msgstr "Vysunout filament 5"
-
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Eject"
 msgstr "Vysunout"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1434
 msgid "Ejecting filament"
 msgstr "Vysouvam filament"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Kon. spinac nesepnut"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Koncovy spinac"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Konc. spinace"
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Chyba - Doslo k prepisu staticke pameti!"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4391
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "CHYBA: Filament senzor nereaguje, zkontrolujte zapojeni."
 
@@ -375,38 +335,13 @@ msgstr "CHYBA: Filament senzor nereaguje, zkontrolujte zapojeni."
 msgid "ERROR:"
 msgstr "CHYBA:"
 
-# 
-#: Marlin_main.cpp:1006
-msgid "External SPI flash W25X20CL not responding."
-msgstr "Externi SPI flash W25X20CL neodpovida."
-
-# 
-#: ultralcd.cpp:5633
-msgid "Extruder 1"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5634
-msgid "Extruder 2"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5635
-msgid "Extruder 3"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5636
-msgid "Extruder 4"
-msgstr ""
-
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Levy vent.:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2133
 msgid "Extruder info"
 msgstr ""
 
@@ -416,12 +351,12 @@ msgid "Extruder"
 msgstr ""
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
-msgstr ""
+msgstr "Selhani MMU"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5082
 msgid "F. autoload  [on]"
 msgstr "F. autozav. [zap]"
 
@@ -431,14 +366,14 @@ msgid "F. autoload [N/A]"
 msgstr "F. autozav. [N/A]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5084
 msgid "F. autoload [off]"
 msgstr "F. autozav. [vyp]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
-msgstr ""
+msgstr "Selhani"
 
 # MSG_FAN_SPEED c=14
 #: messages.c:31
@@ -446,17 +381,17 @@ msgid "Fan speed"
 msgstr "Rychlost vent."
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventilatoru"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5577
 msgid "Fans check   [on]"
 msgstr "Kontr. vent.[zap]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5579
 msgid "Fans check  [off]"
 msgstr "Kontr. vent.[vyp]"
 
@@ -465,13 +400,8 @@ msgstr "Kontr. vent.[vyp]"
 msgid "Fil. sensor  [on]"
 msgstr "Fil. senzor [zap]"
 
-# MSG_RESPONSE_POOR c=20 r=2
-#: Marlin_main.cpp:3146
-msgid "Fil. sensor response is poor, disable it?"
-msgstr "Senzor nerozpoznal filament, vypnout?"
-
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5062
 msgid "Fil. sensor [N/A]"
 msgstr "Fil. senzor [N/A]"
 
@@ -481,9 +411,9 @@ msgid "Fil. sensor [off]"
 msgstr "Fil. senzor [vyp]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Filam. runouts"
-msgstr ""
+msgstr "Vypadky filamentu"
 
 # MSG_FILAMENT_CLEAN c=20 r=2
 #: messages.c:32
@@ -491,32 +421,27 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament vytlacen a spravne barvy?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2672
 msgid "Filament not loaded"
 msgstr "Filament nezaveden"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Senzor filamentu"
 
-# MSG_SELFTEST_FILAMENT_SENSOR c=18
-#: ultralcd.cpp:7477
-msgid "Filament sensor:"
-msgstr "Senzor filamentu:"
-
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2841
 msgid "Filament used"
 msgstr "Spotrebovano filamentu"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2841
 msgid "Print time"
 msgstr "Cas tisku"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Soubor nekompletni. Pokracovat?"
 
@@ -526,52 +451,52 @@ msgid "Finishing movements"
 msgstr "Dokoncovani pohybu"
 
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Kal. prvni vrstvy"
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4896
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Nejdriv pomoci selftestu zkontoluji nejcastejsi chyby vznikajici pri sestaveni tiskarny."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Opravte chybu a pote stisknete tlacitko na jednotce MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Prutok"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2095
 msgid "forum.prusa3d.com"
 msgstr ""
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Predni tiskovy vent?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3220
 msgid "Front side[um]"
 msgstr "Vpredu [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Predni/levy vent."
 
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Topeni/Termistor"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8468
 msgid "Heating disabled by safety timer."
 msgstr "Zahrivani preruseno bezpecnostnim casovacem."
 
@@ -586,67 +511,62 @@ msgid "Heating"
 msgstr "Zahrivani"
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4875
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Dobry den, jsem vase tiskarna Original Prusa i3. Chcete abych Vas provedla kalibracnim procesem?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2096
 msgid "howto.prusa3d.com"
 msgstr ""
 
-# 
-#: ultralcd.cpp:6087
-msgid "Change extruder"
-msgstr "Zmenit extruder"
-
 # MSG_FILAMENTCHANGE
 #: messages.c:37
 msgid "Change filament"
 msgstr "Vymenit filament"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2587
 msgid "Change success!"
 msgstr "Zmena uspesna!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2664
 msgid "Changed correctly?"
 msgstr "Vymena ok?"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Kontrola podlozky"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Kontrola endstopu"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Kontrola hotend "
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Kontrola senzoru"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Kontrola osy X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Kontrola osy Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Kontrola osy Z"
 
@@ -666,112 +586,82 @@ msgid "Filament"
 msgstr ""
 
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4905
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Nyni provedu xyz kalibraci. Zabere to priblizne 12 min."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4913
 msgid "I will run z calibration now."
 msgstr "Nyni provedu z kalibraci."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4978
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Zacnu tisknout linku a Vy budete postupne snizovat trysku otacenim tlacitka dokud nedosahnete optimalni vysky. Prohlednete si obrazky v nasi prirucce v kapitole Kalibrace."
 
-# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
-#: mesh_bed_calibration.cpp:2481
-msgid "Improving bed calibration point"
-msgstr "Zlepsuji presnost kalibracniho bodu"
-
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Informace"
 
-# MSG_FILAMENT_LOADING_T0 c=20 r=4
-#: messages.c:33
-msgid "Insert filament into extruder 1. Click when done."
-msgstr "Vlozte filament do extruderu 1. Potvrdte tlacitkem."
-
-# MSG_FILAMENT_LOADING_T1 c=20 r=4
-#: messages.c:34
-msgid "Insert filament into extruder 2. Click when done."
-msgstr "Vlozte filament do extruderu 2. Potvrdte tlacitkem."
-
-# MSG_FILAMENT_LOADING_T2 c=20 r=4
-#: messages.c:35
-msgid "Insert filament into extruder 3. Click when done."
-msgstr "Vlozte filament do extruderu 3. Potvrdte tlacitkem."
-
-# MSG_FILAMENT_LOADING_T3 c=20 r=4
-#: messages.c:36
-msgid "Insert filament into extruder 4. Click when done."
-msgstr "Vlozte filament do extruderu 4. Potvrdte tlacitkem."
-
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:4938
 msgid "Is filament 1 loaded?"
 msgstr "Je filament 1 zaveden?"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2572
 msgid "Insert filament"
 msgstr "Vlozte filament"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4941
 msgid "Is filament loaded?"
 msgstr "Je filament zaveden?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4972
 msgid "Is it PLA filament?"
 msgstr "Je to PLA filament?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4704
 msgid "Is PLA filament loaded?"
 msgstr "Je PLA filament zaveden?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "Je tiskovy plat na podlozce?"
 
-# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
-#: mesh_bed_calibration.cpp:2223
-msgid "Iteration "
-msgstr "Iterace "
-
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1840
 msgid "Last print failures"
-msgstr ""
+msgstr "Selhani posl. tisku"
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1823
 msgid "Last print"
-msgstr ""
+msgstr "Posledni tisk"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Levy vent na trysce?"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2970
 msgid "Left"
 msgstr "Vlevo:"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3218
 msgid "Left side [um]"
 msgstr "Vlevo [um]"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5594
 msgid "Lin. correction"
 msgstr "Korekce lin."
 
@@ -786,7 +676,7 @@ msgid "Load filament"
 msgstr "Zavest filament"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2612
 msgid "Loading color"
 msgstr "Cisteni barvy"
 
@@ -796,92 +686,92 @@ msgid "Loading filament"
 msgstr "Zavadeni filamentu"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Uvolnena remenicka"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6719
 msgid "Load to nozzle"
 msgstr "Zavest do trysky"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Kal. prvni vrstvy"
 
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Hlavni nabidka"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Merim referencni vysku kalibracniho bodu"
 
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5677
 msgid "Mesh Bed Leveling"
 msgstr ""
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Pokracuji v tisku..."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Pokracuji v nahrivani..."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3005
 msgid "Measured skew"
 msgstr "Merene zkoseni"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU fails"
-msgstr ""
+msgstr "Selhani MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1613
 msgid "MMU load failed     "
-msgstr ""
+msgstr "Zavedeni MMU selhalo"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU load fails"
-msgstr ""
+msgstr "MMU selhani zavadeni"
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Pokracuji..."
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Mod      [Normal]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Mod       [tichy]"
 
 # 
-#: mmu.cpp:635
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU potrebuje zasah uzivatele."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "MMU power fails"
-msgstr ""
+msgstr "MMU vypadky proudu"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Mod       [tichy]"
 
@@ -891,62 +781,62 @@ msgid "Mode [auto power]"
 msgstr "Mod [automaticky]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Mod  [vys. vykon]"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2108
 msgid "MMU2 connected"
-msgstr ""
+msgstr "MMU2 pripojeno"
 
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr ""
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5566
 msgid "Move axis"
 msgstr "Posunout osu"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4294
 msgid "Move X"
 msgstr "Posunout X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4295
 msgid "Move Y"
 msgstr "Posunout Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4296
 msgid "Move Z"
 msgstr "Posunout Z"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5291
 msgid "No move."
 msgstr "Bez pohybu."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6686
 msgid "No SD card"
 msgstr "Zadna SD karta"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2976
 msgid "N/A"
 msgstr ""
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Ne"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Nezapojeno "
 
@@ -955,78 +845,73 @@ msgstr "Nezapojeno "
 msgid "New firmware version available:"
 msgstr "Vysla nova verze firmware:"
 
-# 
-#: 
-msgid "No "
-msgstr "Ne"
-
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Netoci se"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4977
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Nyni zkalibruji vzdalenost mezi koncem trysky a povrchem podlozky."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4921
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Nyni predehreji trysku pro PLA."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Tryska"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1519
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Neplatne hodnoty nastaveni. Bude pouzito vychozi PID, Esteps atd."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4912
 msgid "Now remove the test print from steel sheet."
 msgstr "Nyni odstrante testovaci vytisk z tiskoveho platu."
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:1782
 msgid "Nozzle FAN"
-msgstr ""
+msgstr "Trysk. vent."
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6649
 msgid "Pause print"
 msgstr "Pozastavit tisk"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1598
 msgid "PID cal.           "
 msgstr "PID kal. "
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1604
 msgid "PID cal. finished"
 msgstr "PID kal. ukoncena"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5683
 msgid "PID calibration"
 msgstr "PID kalibrace"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:843
 msgid "PINDA Heating"
 msgstr "Nahrivani PINDA"
 
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Umistete list papiru na podlozku a udrzujte jej pod tryskou behem mereni prvnich 4 bodu. Pokud tryska zachyti papir, okamzite vypnete tiskarnu."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4986
 msgid "Please clean heatbed and then press the knob."
 msgstr "Prosim ocistete podlozku a stisknete tlacitko."
 
@@ -1036,92 +921,92 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Pro uspesnou kalibraci ocistete prosim tiskovou trysku. Potvrdte tlacitkem."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Zkontrolujte :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Prosim nahlednete do prirucky 3D tiskare a opravte problem. Pote obnovte Pruvodce restartovanim tiskarny."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4808
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Prosim vlozte PLA filament do extruderu, pote stisknete tlacitko pro zavedeni filamentu."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4709
 msgid "Please load PLA filament first."
 msgstr "Nejdrive prosim zavedte PLA filament."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3063
 msgid "Please open idler and remove filament manually."
 msgstr "Prosim otevrete idler a manualne odstrante filament."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Umistete prosim tiskovy plat na podlozku"
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Pro vysunuti filamentu stisknete prosim tlacitko"
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4803
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Prosim vlozte PLA filament do trubicky MMU, pote stisknete tlacitko pro zavedeni filamentu."
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Prosim vyjmete urychlene filament"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1440
 msgid "Please remove filament and then press the knob."
 msgstr "Prosim vyjmete filament a pote stisknete tlacitko."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Odstrante prosim tiskovy plat z podlozky."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4354
 msgid "Please run XYZ calibration first."
 msgstr "Nejprve spustte kalibraci XYZ."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1359
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Prosim aktualizujte firmware ve vasi MMU2 jednotce. Cekam na reset."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Prosim cekejte"
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4911
 msgid "Please remove shipping helpers first."
 msgstr "Nejprve prosim sundejte transportni soucastky."
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Predehrejte trysku!"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6636
 msgid "Preheat"
 msgstr "Predehrev"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Predehrivam trysku. Prosim cekejte."
 
@@ -1131,32 +1016,32 @@ msgid "Please upgrade."
 msgstr "Prosim aktualizujte."
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10365
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Pro nahrati trysky a pokracovani stisknete tlacitko."
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Power failures"
-msgstr ""
+msgstr "Vypadky proudu"
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Tisk prerusen"
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2276
 msgid "Preheating to load"
-msgstr ""
+msgstr "Predehrivam k zavedeni"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2280
 msgid "Preheating to unload"
-msgstr ""
+msgstr "Predehrivam k vyjmuti"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Tiskovy vent.:"
 
@@ -1166,17 +1051,17 @@ msgid "Print from SD"
 msgstr "Tisk z SD"
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2206
 msgid "Press the knob"
-msgstr ""
+msgstr "Stisknete hl. tlacitko"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1061
 msgid "Print paused"
 msgstr "Tisk pozastaven"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Pro pokracovani nahrivani trysky stisknete tlacitko."
 
@@ -1186,37 +1071,27 @@ msgid "Printer has not been calibrated yet. Please follow the manual, chapter Fi
 msgstr "Tiskarna nebyla jeste zkalibrovana. Postupujte prosim podle manualu, kapitola Zaciname, odstavec Postup kalibrace."
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1784
 msgid "Print FAN"
-msgstr ""
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK2.5 ready."
-msgstr "Prusa i3 MK2.5 ok."
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK3 ready."
-msgstr "Prusa i3 MK3 ok."
+msgstr "Tiskovy vent."
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2094
 msgid "prusa3d.com"
 msgstr ""
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3221
 msgid "Rear side [um]"
 msgstr "Vzadu [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9765
 msgid "Recovering print    "
 msgstr "Obnovovani tisku "
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Vyjmete stary filament a stisknete tlacitko pro zavedeni noveho."
 
@@ -1225,63 +1100,58 @@ msgstr "Vyjmete stary filament a stisknete tlacitko pro zavedeni noveho."
 msgid "Prusa i3 MK3S OK."
 msgstr ""
 
-# 
-#: 
-msgid "Prusa i3 MK2 ready."
-msgstr "Prusa i3 MK2 ok."
-
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5688
 msgid "Reset XYZ calibr."
 msgstr "Reset XYZ kalibr."
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3222
 msgid "Reset"
 msgstr ""
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6656
 msgid "Resume print"
 msgstr "Pokracovat"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Obnoveni tisku"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3219
 msgid "Right side[um]"
 msgstr "Vpravo [um]"
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5606
 msgid "RPi port     [on]"
 msgstr "RPi port    [zap]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5604
 msgid "RPi port    [off]"
 msgstr "RPi port    [vyp]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4726
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Spusteni Pruvodce vymaze ulozene vysledky vsech kalibraci a spusti kalibracni proces od zacatku. Pokracovat?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5236
 msgid "SD card  [normal]"
-msgstr "SD card  [normal]"
+msgstr ""
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5234
 msgid "SD card [flshAir]"
 msgstr "SD card [FlshAir]"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2971
 msgid "Right"
 msgstr "Vpravo"
 
@@ -1291,217 +1161,207 @@ msgid "Searching bed calibration point"
 msgstr "Hledam kalibracni bod podlozky"
 
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5613
 msgid "Select language"
 msgstr "Vyber jazyka"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr ""
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Self test start "
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5664
 msgid "Selftest         "
 msgstr "Selftest "
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Chyba Selftestu!"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Selftest selhal "
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1551
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Pro kalibraci presneho rehomovani bude nyni spusten selftest."
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4959
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Vyberte teplotu predehrati trysky ktera odpovida vasemu materialu."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Select PLA filament:"
 msgstr "Vyberte PLA filament:"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3230
 msgid "Set temperature:"
 msgstr "Nastavte teplotu:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Nastaveni"
 
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5685
 msgid "Show end stops"
 msgstr "Stav konc. spin."
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:3941
 msgid "Sensor state"
-msgstr ""
-
-# 
-#: 
-msgid "Sensors info"
-msgstr ""
-
-# 
-#: 
-msgid "Show pinda state"
-msgstr "Zobrazit stav PINDA"
+msgstr "Stav senzoru"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Nektere soubory nebudou setrideny. Maximalni pocet souboru ve slozce pro setrideni je 100."
 
 # MSG_SORT_NONE c=17 r=1
-#: ultralcd.cpp:5043
-msgid "Sort:      [none]"
+#: ultralcd.cpp:5246
+msgid "Sort       [none]"
 msgstr "Trideni   [Zadne]"
 
 # MSG_SORT_TIME c=17 r=1
-#: ultralcd.cpp:5041
-msgid "Sort:      [time]"
-msgstr "Trideni:    [cas]"
+#: ultralcd.cpp:5244
+msgid "Sort       [time]"
+msgstr "Trideni     [cas]"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3008
 msgid "Severe skew"
 msgstr "Tezke zkoseni"
 
 # MSG_SORT_ALPHA c=17 r=1
-#: ultralcd.cpp:5042
-msgid "Sort:  [alphabet]"
+#: ultralcd.cpp:5245
+msgid "Sort   [alphabet]"
 msgstr "Trideni [Abeceda]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Trideni souboru"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Zvuk    [hlasity]"
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3007
 msgid "Slight skew"
 msgstr "Lehke zkoseni"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#: 
 msgid "Sound      [mute]"
 msgstr "Zvuk    [vypnuto]"
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4870
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Vyskytl se problem, srovnavam osu Z ..."
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Zvuk     [jednou]"
 
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Zvuk      [tichy]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Rychlost"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Toci se"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4367
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Je vyzadovana stabilni pokojova teplota 21-26C a pevna podlozka."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistika "
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Zastavit tisk"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ZASTAVENO."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Podpora"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Prohozene"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Tepl. kal. "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5600
 msgid "Temp. cal.   [on]"
 msgstr "Tepl. kal.  [zap]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5598
 msgid "Temp. cal.  [off]"
 msgstr "Tepl. kal.  [vyp]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5694
 msgid "Temp. calibration"
 msgstr "Teplot. kalibrace"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3867
 msgid "Temperature calibration failed"
 msgstr "Teplotni kalibrace selhala"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Teplotni kalibrace dokoncena a je nyni aktivni. Teplotni kalibraci je mozno deaktivovat v menu Nastaveni->Tepl. kal."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5564
 msgid "Temperature"
 msgstr "Teplota"
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2140
 msgid "Temperatures"
 msgstr "Teploty"
 
@@ -1511,127 +1371,122 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Je potreba kalibrovat osu Z. Prosim postupujte dle prirucky, kapitola Zaciname, sekce Postup kalibrace."
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2863
 msgid "Total filament"
 msgstr "Filament celkem"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2863
 msgid "Total print time"
 msgstr "Celkovy cas tisku"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6633
 msgid "Tune"
 msgstr "Ladit"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Unload"
 msgstr "Vysunout"
 
 # 
-#: ultralcd.cpp:5617
-msgid "Unload all"
-msgstr "Vyjmout vse"
-
-# 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "Total failures"
-msgstr ""
+msgstr "Celkem selhani"
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2213
 msgid "to load filament"
-msgstr ""
+msgstr "k zavedeni filamentu"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2217
 msgid "to unload filament"
-msgstr ""
+msgstr "k vyjmuti filamentu"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Vyjmout filament"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Vysouvam filament"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1824
 msgid "Total"
-msgstr ""
+msgstr "Celkem"
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5822
 msgid "Used during print"
 msgstr "Pouzite behem tisku"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2143
 msgid "Voltages"
 msgstr "Napeti"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2116
 msgid "unknown"
-msgstr ""
+msgstr "neznamy"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5262
 msgid "Wait for user..."
 msgstr "Ceka se na uzivatele..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3374
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Cekani na zchladnuti trysky a podlozky."
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3338
 msgid "Waiting for PINDA probe cooling"
 msgstr "Cekani na zchladnuti PINDA"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4782
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Pouzijte vyjmout pro odstraneni filamentu 1 pokud presahuje z PTFE trubicky za tiskarnou. Pouzijte vysunout, pokud neni videt."
 
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1511
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Varovani: doslo ke zmene typu tiskarny a motherboardu."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1503
 msgid "Warning: motherboard type changed."
 msgstr "Varovani: doslo ke zmene typu motherboardu."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1507
 msgid "Warning: printer type changed."
 msgstr "Varovani: doslo ke zmene typu tiskarny."
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3053
 msgid "Was filament unload successful?"
 msgstr "Bylo vysunuti filamentu uspesne?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Chyba zapojeni"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5661
 msgid "Wizard"
 msgstr "Pruvodce"
 
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2132
 msgid "XYZ cal. details"
 msgstr "Detaily XYZ kal."
 
@@ -1641,107 +1496,312 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Kalibrace XYZ selhala. Nahlednete do manualu."
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Ano"
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Pruvodce muzete kdykoliv znovu spustit z menu Kalibrace -> Pruvodce"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3838
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Kalibrace XYZ v poradku. Zkoseni bude automaticky vyrovnano pri tisku."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Kalibrace XYZ v poradku. X/Y osy mirne zkosene. Dobra prace!"
 
 # 
-#: ultralcd.cpp:4885
-msgid "X-correct"
-msgstr "Korekce X"
+#: ultralcd.cpp:5044
+msgid "X-correct:"
+msgstr "Korekce X:"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3832
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Kalibrace XYZ v poradku. X/Y osy jsou kolme. Gratuluji!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Kalibrace XYZ nepresna. Predni kalibracni body moc vpredu."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3819
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Kalibrace XYZ nepresna. Pravy predni bod moc vpredu."
 
-# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
-#: ultralcd.cpp:3699
-msgid "XYZ calibration compromised. Left front calibration point not reachable."
-msgstr "Kalibrace XYZ nepresna. Levy predni bod moc vpredu."
-
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6080
 msgid "Load all"
 msgstr "Zavest vse"
 
-# MSG_LOAD_FILAMENT_1 c=17
-#: ultralcd.cpp:5576
-msgid "Load filament 1"
-msgstr "Zavest filament 1"
-
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3798
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Kalibrace XYZ selhala. Kalibracni bod podlozky nenalezen."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Kalibrace XYZ selhala. Predni kalibracni body moc vpredu. Srovnejte tiskarnu."
 
 # 
-#: ultralcd.cpp:3687
-msgid "XYZ calibration failed. Left front calibration point not reachable."
-msgstr "Kalibrace XYZ selhala. Levy predni bod moc vpredu. Srovnejte tiskarnu."
-
-# MSG_LOAD_FILAMENT_2 c=17
-#: ultralcd.cpp:5577
-msgid "Load filament 2"
-msgstr "Zavest filament 2"
-
-# 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3807
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Kalibrace XYZ selhala. Pravy predni bod moc vpredu. Srovnejte tiskarnu."
 
-# MSG_LOAD_FILAMENT_3 c=17
-#: ultralcd.cpp:5578
-msgid "Load filament 3"
-msgstr "Zavest filament 3"
-
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2968
 msgid "Y distance from min"
 msgstr "Y vzdalenost od min"
 
 # 
-#: ultralcd.cpp:4886
-msgid "Y-correct"
-msgstr "Korekce Y"
+#: ultralcd.cpp:5045
+msgid "Y-correct:"
+msgstr "Korekce Y:"
 
-# MSG_LOAD_FILAMENT_4 c=17
-#: ultralcd.cpp:5579
-msgid "Load filament 4"
-msgstr "Zavest filament 4"
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr ""
+
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Zpet"
+
+# 
+#: ultralcd.cpp:5553
+msgid "Checks"
+msgstr "Kontrola"
+
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falesne spusteni"
+
+# 
+#: ultralcd.cpp:3946
+msgid "FINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5459
+msgid "Firmware   [none]"
+msgstr "Firmware  [Zadne]"
+
+# 
+#: ultralcd.cpp:5465
+msgid "Firmware [strict]"
+msgstr "Firmware [Prisne]"
+
+# 
+#: ultralcd.cpp:5462
+msgid "Firmware   [warn]"
+msgstr "Firmware[Varovat]"
+
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "HW nastaveni"
+
+# 
+#: ultralcd.cpp:3950
+msgid "IR:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Komp. magnetu[N/A]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Komp. magnetu[Vyp]"
+
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Komp. magnetu[Zap]"
+
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Mesh         [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Mesh         [7x7]"
+
+# 
+#: ultralcd.cpp:5591
+msgid "Mesh bed leveling"
+msgstr "Mesh Bed Leveling"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5220
+msgid "MMU Mode [Normal]"
+msgstr "MMU mod  [Normal]"
+
+# 
+#: ultralcd.cpp:5221
+msgid "MMU Mode[Stealth]"
+msgstr "MMU Mod   [Tichy]"
+
+# 
+#: ultralcd.cpp:4427
+msgid "Mode change in progress ..."
+msgstr "Probiha zmena modu..."
+
+# 
+#: ultralcd.cpp:5420
+msgid "Model      [none]"
+msgstr "Model     [Zadne]"
+
+# 
+#: ultralcd.cpp:5426
+msgid "Model    [strict]"
+msgstr "Model    [Prisne]"
+
+# 
+#: ultralcd.cpp:5423
+msgid "Model      [warn]"
+msgstr "Model   [Varovat]"
+
+# 
+#: ultralcd.cpp:5381
+msgid "Nozzle d.  [0.25]"
+msgstr "Tryska     [0.25]"
+
+# 
+#: ultralcd.cpp:5384
+msgid "Nozzle d.  [0.40]"
+msgstr "Tryska     [0.40]"
+
+# 
+#: ultralcd.cpp:5387
+msgid "Nozzle d.  [0.60]"
+msgstr "Tryska     [0.60]"
+
+# 
+#: ultralcd.cpp:5335
+msgid "Nozzle     [none]"
+msgstr "Tryska    [Zadne]"
+
+# 
+#: ultralcd.cpp:5341
+msgid "Nozzle   [strict]"
+msgstr "Tryska   [Prisne]"
+
+# 
+#: ultralcd.cpp:5338
+msgid "Nozzle     [warn]"
+msgstr "Tryska  [Varovat]"
+
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:3942
+msgid "PINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2286
+msgid "Preheating to cut"
+msgstr "Predehrivam k ustrizeni"
+
+# 
+#: ultralcd.cpp:2283
+msgid "Preheating to eject"
+msgstr "Predehrivam k vysunuti"
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Prumer trysky tiskarny se lisi od G-code. Pokracovat?"
 
-# MSG_LOAD_FILAMENT_5 c=17
-#: ultralcd.cpp:5582
-msgid "Load filament 5"
-msgstr "Zavest filament 5"
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Prumer trysky tiskarny se lisi od G-code. Prosim zkontrolujte nastaveni. Tisk zrusen."
+
+# 
+#: ultralcd.cpp:6597
+msgid "Rename"
+msgstr "Prejmenovat"
+
+# 
+#: ultralcd.cpp:6593
+msgid "Select"
+msgstr "Vybrat"
+
+# 
+#: ultralcd.cpp:2134
+msgid "Sensor info"
+msgstr "Senzor info"
+
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Plech"
+
+# 
+#: 
+msgid "Sound     [assist]"
+msgstr "Zvuk   [asistence]"
+
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr "Tiskove plechy"
+
+# 
+#: ultralcd.cpp:5046
+msgid "Z-correct:"
+msgstr "Korekce Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Pocet mereni Z [1]"
 

lang/po/Firmware_de.po

@@ -7,8 +7,8 @@ msgstr ""
 "Content-Transfer-Encoding: 8bit\n"
 "Language: de\n"
 "Project-Id-Version: Prusa-Firmware\n"
-"POT-Creation-Date: čt 7. úno 2019 14:44:19\n"
-"PO-Revision-Date: čt 7. úno 2019 14:44:19\n"
+"POT-Creation-Date: Wed Sep 4 16:13:46 CEST 2019\n"
+"PO-Revision-Date: Wed Sep 4 16:13:46 CEST 2019\n"
 "Language-Team: \n"
 "X-Generator: Poedit 2.0.7\n"
 "X-Poedit-SourceCharset: UTF-8\n"
@@ -21,72 +21,72 @@ msgid " of 4"
 msgstr " von 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " von 9"
 
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3027
 msgid "[0;0] point offset"
 msgstr "[0;0] Punktversatz"
 
 # MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
-#: ultralcd.cpp:4219
-msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
-msgstr "\x1b[2JCrash Erkennung kann\x1b[1;0Hnur im Modus Normal\x1b[2;0Hgenutzt werden"
+#: 
+msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
+msgstr "Crash Erkennung kann\x0anur im Modus Normal\x0agenutzt werden"
 
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-#: ultralcd.cpp:4231
-msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
-msgstr "\x1b[2JWARNUNG:\x1b[1;0HCrash Erkennung\x1b[2;0Hdeaktiviert im\x1b[3;0HStealth Modus"
+#: 
+msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
+msgstr "WARNUNG:\x0aCrash Erkennung\x0adeaktiviert im\x0aStealth Modus"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2290
 msgid ">Cancel"
-msgstr ""
+msgstr ">Abbruch"
 
-# MSG_BABYSTEPPING_Z c=20
-#: ultralcd.cpp:3043
-msgid "Adjusting Z"
-msgstr "Z wurde eingestellt"
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3147
+msgid "Adjusting Z:"
+msgstr "Z Anpassen:"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Alles richtig "
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Alles abgeschlossen. Viel Spass beim Drucken!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1974
 msgid "Ambient"
-msgstr ""
+msgstr "Raumtemp."
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2576
 msgid "and press the knob"
 msgstr "und Knopf druecken"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3445
 msgid "Are left and right Z~carriages all up?"
 msgstr "Sind linke+rechte Z- Schlitten ganz oben?"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5114
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin    [an]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5110
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin   [N/V]"
 
-#  MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+# MSG_AUTO_DEPLETE_OFF c=17 r=1
+#: ultralcd.cpp:5118
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [aus]"
 
@@ -96,32 +96,32 @@ msgid "Auto home"
 msgstr "Startposition"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6736
 msgid "AutoLoad filament"
 msgstr "Auto-Laden Filament"
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4378
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Automatisches Laden Filament nur bei einge schaltetem Filament- sensor verfuegbar..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2771
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Automatisches Laden Filament ist aktiv, Knopf druecken und Filament einlegen..."
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Achsenlaenge"
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Achse"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Bett / Heizung"
 
@@ -136,7 +136,7 @@ msgid "Bed Heating"
 msgstr "Bett aufwaermen"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5682
 msgid "Bed level correct"
 msgstr "Ausgleich Bett ok"
 
@@ -145,38 +145,28 @@ msgstr "Ausgleich Bett ok"
 msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
 msgstr "Z-Kal. fehlgeschlg. Sensor nicht ausgeloest. Schmutzige Duese? Warte auf Reset."
 
-# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
-#: Marlin_main.cpp:4508
-msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
-msgstr "Z-Kalibrierung fehl- geschlagen. Sensor getrennt/Kabelbruch? Warte auf Reset."
-
-# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
-#: Marlin_main.cpp:4512
-msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
-msgstr "Z-Kalibrierung fehl- geschlagen. Sensor zu hoch ausgeloest. Warte auf Reset."
-
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Bett"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2002
 msgid "Belt status"
 msgstr "Gurtstatus"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Stromausfall! Druck wiederherstellen?"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
-msgstr ""
+msgstr "Kalibriere Start"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5671
 msgid "Calibrate XYZ"
 msgstr "Kalibrierung XYZ"
 
@@ -186,12 +176,12 @@ msgid "Calibrate Z"
 msgstr "Kalibrierung Z"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4570
 msgid "Calibrate"
 msgstr "Kalibrieren"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "XYZ Kalibrieren: Drehen Sie den Knopf bis der obere Anschlag erreicht wird. Anschliessend den Knopf druecken."
 
@@ -201,37 +191,32 @@ msgid "Calibrating Z"
 msgstr "Kalibrierung Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Z Kalibrieren: Drehen Sie den Knopf bis der obere Anschlag erreicht wird. Anschliessend den Knopf druecken."
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:813
 msgid "Calibration done"
 msgstr "Kalibrierung OK"
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Kalibrierung"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Cancel"
 msgstr "Abbruch"
 
-# MSG_SD_INSERTED
-#: 
-msgid "Card inserted"
-msgstr "SD Karte eingesetzt"
-
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "SD Karte entfernt"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2676
 msgid "Color not correct"
 msgstr "Falsche Farbe"
 
@@ -241,7 +226,7 @@ msgid "Cooldown"
 msgstr "Abkuehlen"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4503
 msgid "Copy selected language?"
 msgstr "Gewaehlte Sprache kopieren?"
 
@@ -266,27 +251,27 @@ msgid "Crash detected."
 msgstr "Crash erkannt."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:600
 msgid "Crash detected. Resume print?"
 msgstr "Crash erkannt. Druck fortfuehren?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Crash"
 msgstr ""
 
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5823
 msgid "Current"
 msgstr "Aktuelles"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2102
 msgid "Date:"
 msgstr "Datum:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5568
 msgid "Disable steppers"
 msgstr "Motoren aus"
 
@@ -296,77 +281,52 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Der Abstand zwischen der Spitze der Duese und dem Bett ist noch nicht eingestellt. Bitte folgen Sie dem Handbuch, Kapitel Erste Schritte, Abschnitt Erste Schicht Kalibrierung."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4984
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Moechten Sie den letzten Schritt wiederholen, um den Abstand zwischen Duese und Druckbett neu einzustellen?"
 
-# MSG_EXTRUDER_CORRECTION c=9
-#: ultralcd.cpp:4889
-msgid "E-correct"
-msgstr "E-Korrektur"
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5048
+msgid "E-correct:"
+msgstr "E-Korrektur:"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Filamentauswurf"
 
-# MSG_EJECT_FILAMENT1 c=17 r=1
-#: ultralcd.cpp:5603
-msgid "Eject filament 1"
-msgstr "Filamentauswurf 1"
-
-# MSG_EJECT_FILAMENT2 c=17 r=1
-#: ultralcd.cpp:5604
-msgid "Eject filament 2"
-msgstr "Fil.2 auswerfen"
-
-# MSG_EJECT_FILAMENT3 c=17 r=1
-#: ultralcd.cpp:5605
-msgid "Eject filament 3"
-msgstr "Fil.3 auswerfen"
-
-# MSG_EJECT_FILAMENT4 c=17 r=1
-#: ultralcd.cpp:5606
-msgid "Eject filament 4"
-msgstr "Fil.4 auswerfen"
-
-# MSG_EJECT_FILAMENT5 c=17 r=1
-#: ultralcd.cpp:5607
-msgid "Eject filament 5"
-msgstr "Fil.5 auswerfen"
-
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Eject"
 msgstr "Auswurf"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1434
 msgid "Ejecting filament"
 msgstr "werfe Filament aus"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Ende nicht getroffen"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Endanschlag"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Endschalter"
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Fehler - statischer Speicher wurde ueberschrieben"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4391
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "FEHLER: Filament- sensor reagiert nicht, bitte Verbindung pruefen."
 
@@ -375,38 +335,13 @@ msgstr "FEHLER: Filament- sensor reagiert nicht, bitte Verbindung pruefen."
 msgid "ERROR:"
 msgstr "FEHLER:"
 
-# 
-#: Marlin_main.cpp:1006
-msgid "External SPI flash W25X20CL not responding."
-msgstr "Der externe SPI Flash W25X20CL antwortet nicht."
-
-# 
-#: ultralcd.cpp:5633
-msgid "Extruder 1"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5634
-msgid "Extruder 2"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5635
-msgid "Extruder 3"
-msgstr ""
-
-# 
-#: ultralcd.cpp:5636
-msgid "Extruder 4"
-msgstr ""
-
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Extruder Luefter:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2133
 msgid "Extruder info"
 msgstr "Extruder Info"
 
@@ -416,12 +351,12 @@ msgid "Extruder"
 msgstr ""
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
-msgstr ""
+msgstr "MMU-Fehler"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5082
 msgid "F. autoload  [on]"
 msgstr "F.Autoladen  [an]"
 
@@ -431,14 +366,14 @@ msgid "F. autoload [N/A]"
 msgstr "F. Autoload  [nv]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5084
 msgid "F. autoload [off]"
 msgstr "F. Autoload [aus]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
-msgstr ""
+msgstr "Fehlerstatistik"
 
 # MSG_FAN_SPEED c=14
 #: messages.c:31
@@ -446,17 +381,17 @@ msgid "Fan speed"
 msgstr "Luefter-Tempo"
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Lueftertest"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5577
 msgid "Fans check   [on]"
 msgstr "Luefter Chk. [an]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5579
 msgid "Fans check  [off]"
 msgstr "Luefter Chk.[aus]"
 
@@ -465,13 +400,8 @@ msgstr "Luefter Chk.[aus]"
 msgid "Fil. sensor  [on]"
 msgstr "Fil. Sensor  [an]"
 
-# MSG_RESPONSE_POOR c=20 r=2
-#: Marlin_main.cpp:3146
-msgid "Fil. sensor response is poor, disable it?"
-msgstr "Fil. Sensorsignal ist schlecht, ausschalten?"
-
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5062
 msgid "Fil. sensor [N/A]"
 msgstr "Fil. Sensor  [nv]"
 
@@ -481,9 +411,9 @@ msgid "Fil. sensor [off]"
 msgstr "Fil. Sensor [aus]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Filam. runouts"
-msgstr ""
+msgstr "Filam. Maengel"
 
 # MSG_FILAMENT_CLEAN c=20 r=2
 #: messages.c:32
@@ -491,32 +421,27 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament extrudiert + richtige Farbe?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2672
 msgid "Filament not loaded"
 msgstr "Fil. nicht geladen"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Filamentsensor"
 
-# MSG_SELFTEST_FILAMENT_SENSOR c=18
-#: ultralcd.cpp:7477
-msgid "Filament sensor:"
-msgstr "Filamentsensor:"
-
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2841
 msgid "Filament used"
 msgstr "Filament benutzt"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2841
 msgid "Print time"
 msgstr "Druckzeit"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Datei unvollstaendig Trotzdem fortfahren?"
 
@@ -526,52 +451,52 @@ msgid "Finishing movements"
 msgstr "Bewegung beenden"
 
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Erste-Schicht Kal."
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4896
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Zunaechst fuehre ich den Selbsttest durch, um die haeufigsten Probleme beim Zusammenbau zu ueberpruefen."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Beseitigen Sie das Problem und druecken Sie dann den Knopf am MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Durchfluss"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2095
 msgid "forum.prusa3d.com"
 msgstr ""
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Vorderer Luefter?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3220
 msgid "Front side[um]"
 msgstr "Vorne [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Vorderer/linke Luefter"
 
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Heizung/Thermistor"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8468
 msgid "Heating disabled by safety timer."
 msgstr "Heizung durch Sicherheitstimer deaktiviert."
 
@@ -586,67 +511,62 @@ msgid "Heating"
 msgstr "Aufwaermen"
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4875
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Hallo, ich bin Ihr Original Prusa i3 Drucker. Moechten Sie, dass ich Sie durch den Einrich- tungsablauf fuehre?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2096
 msgid "howto.prusa3d.com"
 msgstr ""
 
-# 
-#: ultralcd.cpp:6087
-msgid "Change extruder"
-msgstr "Wechsel Extruder"
-
 # MSG_FILAMENTCHANGE
 #: messages.c:37
 msgid "Change filament"
 msgstr "Filament-Wechsel"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2587
 msgid "Change success!"
 msgstr "Wechsel erfolgr.!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2664
 msgid "Changed correctly?"
 msgstr "Wechsel ok?"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Pruefe Bett "
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Pruefe Endschalter"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Pruefe Duese  "
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Pruefe Sensoren "
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Pruefe X Achse "
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Pruefe Y Achse "
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Pruefe Z Achse "
 
@@ -666,112 +586,82 @@ msgid "Filament"
 msgstr ""
 
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4905
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Ich werde jetzt die XYZ-Kalibrierung durchfuehren. Es wird ca. 12 Minuten dauern."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4913
 msgid "I will run z calibration now."
 msgstr "Ich werde jetzt die Z Kalibrierung durchfuehren."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4978
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Ich werde jetzt eine Linie drucken. Waehrend des Druckes koennen Sie die Duese allmaehlich senken, indem Sie den Knopf drehen, bis Sie die optimale Hoehe erreichen. Sehen Sie sich die Bilder in unserem Handbuch im Kapitel Kalibrierung an."
 
-# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
-#: mesh_bed_calibration.cpp:2481
-msgid "Improving bed calibration point"
-msgstr "Verbessere Bett Kalibrierpunkt"
-
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Infoanzeige"
 
-# MSG_FILAMENT_LOADING_T0 c=20 r=4
-#: messages.c:33
-msgid "Insert filament into extruder 1. Click when done."
-msgstr "Filament in Extruder 1 einlegen. Klicken wenn fertig."
-
-# MSG_FILAMENT_LOADING_T1 c=20 r=4
-#: messages.c:34
-msgid "Insert filament into extruder 2. Click when done."
-msgstr "Filament in Extruder 2 einlegen. Klicken wenn fertig."
-
-# MSG_FILAMENT_LOADING_T2 c=20 r=4
-#: messages.c:35
-msgid "Insert filament into extruder 3. Click when done."
-msgstr "Filament in Extruder 3 einlegen. Klicken wenn fertig."
-
-# MSG_FILAMENT_LOADING_T3 c=20 r=4
-#: messages.c:36
-msgid "Insert filament into extruder 4. Click when done."
-msgstr "Filament in Extruder 4 einlegen. Klicken wenn fertig."
-
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:4938
 msgid "Is filament 1 loaded?"
 msgstr "Wurde Filament 1 geladen?"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2572
 msgid "Insert filament"
 msgstr "Filament einlegen"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4941
 msgid "Is filament loaded?"
 msgstr "Ist das Filament geladen?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4972
 msgid "Is it PLA filament?"
 msgstr "Ist es wirklich PLA Filament?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4704
 msgid "Is PLA filament loaded?"
 msgstr "Ist PLA Filament geladen?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "Liegt das Stahlblech auf dem Heizbett?"
 
-# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
-#: mesh_bed_calibration.cpp:2223
-msgid "Iteration "
-msgstr ""
-
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1840
 msgid "Last print failures"
-msgstr ""
+msgstr "Letzte Druckfehler"
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1823
 msgid "Last print"
-msgstr ""
+msgstr "Letzter Druck"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Linker Luefter?"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2970
 msgid "Left"
 msgstr "Links"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3218
 msgid "Left side [um]"
 msgstr "Links [um]"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5594
 msgid "Lin. correction"
 msgstr "Lineare Korrektur"
 
@@ -786,7 +676,7 @@ msgid "Load filament"
 msgstr "Filament laden"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2612
 msgid "Loading color"
 msgstr "Lade Farbe"
 
@@ -796,92 +686,92 @@ msgid "Loading filament"
 msgstr "Filament laedt"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Lose Riemenscheibe"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6719
 msgid "Load to nozzle"
 msgstr "In Druckduese laden"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Erste-Schicht Kal."
 
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Hauptmenue"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Messen der Referenzhoehe des Kalibrierpunktes"
 
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5677
 msgid "Mesh Bed Leveling"
 msgstr "Mesh Bett Ausgleich"
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Position    wiederherstellen... "
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Temperatur wiederherstellen..."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3005
 msgid "Measured skew"
 msgstr "Schraeglauf"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU fails"
-msgstr ""
+msgstr "MMU Fehler"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1613
 msgid "MMU load failed     "
-msgstr ""
+msgstr "MMU Ladefehler"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU load fails"
-msgstr ""
+msgstr "MMU Ladefehler"
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK.  Weiterdrucken..."
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Modus    [Normal]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Modus     [leise]"
 
 # 
-#: mmu.cpp:635
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU erfordert Benutzereingriff."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "MMU power fails"
-msgstr ""
+msgstr "MMU Netzfehler"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Modus   [Stealth]"
 
@@ -891,62 +781,62 @@ msgid "Mode [auto power]"
 msgstr "Modus[Auto Power]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Modus[Hohe Leist]"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2108
 msgid "MMU2 connected"
-msgstr ""
+msgstr "MMU2 verbunden"
 
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr ""
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5566
 msgid "Move axis"
 msgstr "Achse bewegen"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4294
 msgid "Move X"
 msgstr "Bewege X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4295
 msgid "Move Y"
 msgstr "Bewege Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4296
 msgid "Move Z"
 msgstr "Bewege Z"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5291
 msgid "No move."
 msgstr "Keine Bewegung."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6686
 msgid "No SD card"
 msgstr "Keine SD Karte"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2976
 msgid "N/A"
-msgstr ""
+msgstr "N.V."
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Nein"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Nicht angeschlossen"
 
@@ -955,78 +845,73 @@ msgstr "Nicht angeschlossen"
 msgid "New firmware version available:"
 msgstr "Neue Firmware- Version verfuegbar:"
 
-# 
-#: 
-msgid "No "
-msgstr "Nein"
-
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Dreht sich nicht"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4977
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Jetzt werde ich den Abstand zwischen Duesenspitze und Druckbett kalibrieren."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4921
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Jetzt werde ich die Duese fuer PLA vorheizen."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Duese"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1519
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Alte Einstellungen gefunden. Standard PID, E-Steps u.s.w. werden gesetzt."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4912
 msgid "Now remove the test print from steel sheet."
 msgstr "Testdruck jetzt von Stahlblech entfernen."
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:1782
 msgid "Nozzle FAN"
-msgstr ""
+msgstr "Duesen Luefter"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6649
 msgid "Pause print"
 msgstr "Druck pausieren"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1598
 msgid "PID cal.           "
 msgstr "PID Kal.           "
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1604
 msgid "PID cal. finished"
 msgstr "PID Kalib. fertig"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5683
 msgid "PID calibration"
 msgstr "PID Kalibrierung"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:843
 msgid "PINDA Heating"
 msgstr "PINDA erwaermen"
 
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Legen Sie ein Blatt Papier unter die Duese waehrend der Kalibrierung der ersten 4 Punkte. Wenn die Duese das Papier erfasst, den Drucker sofort ausschalten."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4986
 msgid "Please clean heatbed and then press the knob."
 msgstr "Bitte reinigen Sie das Heizbett und druecken Sie dann den Knopf."
 
@@ -1036,92 +921,92 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Bitte entfernen Sie ueberstehendes Filament von der Duese. Klicken wenn sauber."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Bitte pruefe:"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Bitte lesen Sie unser Handbuch und beheben Sie das Problem. Fahren Sie dann mit dem Assistenten fort, indem Sie den Drucker neu starten."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4808
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Legen Sie bitte PLA Filament in den Extruder und druecken Sie den Knopf,  um es zu laden."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4709
 msgid "Please load PLA filament first."
 msgstr "Bitte laden Sie zuerst PLA Filament."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3063
 msgid "Please open idler and remove filament manually."
 msgstr "Bitte Spannrolle oeffnen und Fila- ment von Hand entfernen"
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Bitte legen Sie das Stahlblech auf das Heizbett."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Bitte druecken Sie den Knopf um das Filament zu entladen."
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4803
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Legen Sie bitte PLA Filament in den ersten Schlauch der MMU und druecken Sie den Knopf,  um es zu laden."
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Bitte ziehen Sie das Filament sofort heraus"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1440
 msgid "Please remove filament and then press the knob."
 msgstr "Bitte Filament entfernen und dann den Knopf druecken"
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Bitte entfernen Sie das Stahlblech vom Heizbett."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4354
 msgid "Please run XYZ calibration first."
 msgstr "Bitte zuerst XYZ Kalibrierung ausfuehren."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1359
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Bitte aktualisieren Sie die Firmware in der MMU2. Warte auf Reset."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Bitte warten"
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4911
 msgid "Please remove shipping helpers first."
 msgstr "Bitte zuerst Transportsicherungen entfernen."
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Duese vorheizen!"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6636
 msgid "Preheat"
 msgstr "Vorheizen"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Vorheizen der Duese. Bitte warten."
 
@@ -1131,32 +1016,32 @@ msgid "Please upgrade."
 msgstr "Bitte aktualisieren."
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10365
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Bitte druecken Sie den Knopf um die Duese vorzuheizen und fortzufahren."
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Power failures"
-msgstr ""
+msgstr "Netzfehler"
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Druck abgebrochen"
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2276
 msgid "Preheating to load"
-msgstr ""
+msgstr "Heizen zum Laden"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2280
 msgid "Preheating to unload"
-msgstr ""
+msgstr "Heizen zum Entladen"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Druckvent.:"
 
@@ -1166,17 +1051,17 @@ msgid "Print from SD"
 msgstr "Drucken von SD"
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2206
 msgid "Press the knob"
-msgstr ""
+msgstr "Knopf druecken"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1061
 msgid "Print paused"
 msgstr "Druck pausiert"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Druecken Sie den Knopf um die Duesentemperatur wiederherzustellen"
 
@@ -1186,37 +1071,27 @@ msgid "Printer has not been calibrated yet. Please follow the manual, chapter Fi
 msgstr "Drucker wurde noch nicht kalibriert. Bitte folgen Sie dem Handbuch, Kapitel Erste Schritte, Abschnitt Kalibrie- rungsablauf."
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1784
 msgid "Print FAN"
-msgstr ""
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK2.5 ready."
-msgstr "Prusa i3 MK2.5 bereit."
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK3 ready."
-msgstr "Prusa i3 MK3 bereit."
+msgstr "Druckluefter"
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2094
 msgid "prusa3d.com"
 msgstr ""
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3221
 msgid "Rear side [um]"
 msgstr "Hinten [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9765
 msgid "Recovering print    "
 msgstr "Druck wiederherst    "
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Entfernen Sie das alte Filament und druecken Sie den Knopf, um das neue zu laden."
 
@@ -1225,63 +1100,58 @@ msgstr "Entfernen Sie das alte Filament und druecken Sie den Knopf, um das neue
 msgid "Prusa i3 MK3S OK."
 msgstr ""
 
-# 
-#: 
-msgid "Prusa i3 MK2 ready."
-msgstr "Prusa i3 MK2 bereit."
-
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5688
 msgid "Reset XYZ calibr."
 msgstr "XYZ Kalibr. zuruecksetzen."
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3222
 msgid "Reset"
 msgstr "Ruecksetzen"
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6656
 msgid "Resume print"
 msgstr "Druck fortsetzen"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Druck fortgesetzt"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3219
 msgid "Right side[um]"
-msgstr "Rechts [um]"
+msgstr "Rechts    [um]"
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5606
 msgid "RPi port     [on]"
 msgstr "RPi Port     [an]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5604
 msgid "RPi port    [off]"
 msgstr "RPi Port    [aus]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4726
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Der Assistent wird die aktuellen Kalibrierungsdaten loeschen und von vorne beginnen. Weiterfahren?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5236
 msgid "SD card  [normal]"
 msgstr "SD Karte [normal]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5234
 msgid "SD card [flshAir]"
 msgstr "SD Karte[flshAir]"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2971
 msgid "Right"
 msgstr "Rechts"
 
@@ -1291,217 +1161,207 @@ msgid "Searching bed calibration point"
 msgstr "Suche Bett Kalibrierpunkt"
 
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5613
 msgid "Select language"
 msgstr "Waehle Sprache"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Selbsttest OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Selbsttest start "
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5664
 msgid "Selftest         "
-msgstr "Selbsttest "
+msgstr "Selbsttest       "
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Selbsttest Fehler!"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
-msgstr "Selbsttest misslung  "
+msgstr "Selbsttest misslang"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1551
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Selbsttest im Gang, um die genaue Rueck- kehr zum Nullpunkt ohne Sensor zu kalibrieren"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4959
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Bitte Vorheiztemperatur auswaehlen, die Ihrem Material entspricht."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Select PLA filament:"
 msgstr "PLA Filament auswaehlen:"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3230
 msgid "Set temperature:"
 msgstr "Temp. einstellen:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Einstellungen"
 
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5685
 msgid "Show end stops"
 msgstr "Endschalter Status"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:3941
 msgid "Sensor state"
-msgstr ""
-
-# 
-#: 
-msgid "Sensors info"
-msgstr ""
-
-# 
-#: 
-msgid "Show pinda state"
-msgstr "Pinda-Status anzeigen"
+msgstr "Sensorstatus"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Einige Dateien wur- den nicht sortiert. Max. Dateien pro Verzeichnis = 100."
 
 # MSG_SORT_NONE c=17 r=1
-#: ultralcd.cpp:5043
-msgid "Sort:      [none]"
-msgstr "Sort.:    [Keine]"
+#: ultralcd.cpp:5246
+msgid "Sort       [none]"
+msgstr "Sort.     [Keine]"
 
 # MSG_SORT_TIME c=17 r=1
-#: ultralcd.cpp:5041
-msgid "Sort:      [time]"
-msgstr "Sort.:     [Zeit]"
+#: ultralcd.cpp:5244
+msgid "Sort       [time]"
+msgstr "Sort.      [Zeit]"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3008
 msgid "Severe skew"
 msgstr "Schwerer Schraeglauf"
 
 # MSG_SORT_ALPHA c=17 r=1
-#: ultralcd.cpp:5042
-msgid "Sort:  [alphabet]"
-msgstr "Sort.: [Alphabet]"
+#: ultralcd.cpp:5245
+msgid "Sort   [alphabet]"
+msgstr "Sort.  [Alphabet]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Sortiere Dateien"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Sound      [laut]"
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3007
 msgid "Slight skew"
 msgstr "Leichter Schraeglauf"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#: 
 msgid "Sound      [mute]"
 msgstr "Sound     [stumm]"
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4870
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Fehler aufgetreten, Z-Kalibrierung erforderlich..."
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Sound    [einmal]"
 
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Sound     [leise]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Geschwindigkeit"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Dreht sich"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4367
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Stabile Umgebungs- temperatur 21-26C und feste Stand- flaeche erforderlich"
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistiken "
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Druck abbrechen"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
-msgstr "GESTOPPT. "
+msgstr "GESTOPPT."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr ""
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Ausgetauscht"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
-msgstr "Temp Kalib. "
+msgstr "Temp Kalib.         "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5600
 msgid "Temp. cal.   [on]"
 msgstr "Temp. Kal.   [AN]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5598
 msgid "Temp. cal.  [off]"
 msgstr "Temp. Kal.  [AUS]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5694
 msgid "Temp. calibration"
 msgstr "Temp. kalibrieren"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3867
 msgid "Temperature calibration failed"
 msgstr "Temperaturkalibrierung fehlgeschlagen"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Temp.kalibrierung ist fertig + aktiv. Temp.kalibrierung kann ausgeschaltet werden im Menu Einstellungen -> Temp.kal."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5564
 msgid "Temperature"
 msgstr "Temperatur"
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2140
 msgid "Temperatures"
 msgstr "Temperaturen"
 
@@ -1511,127 +1371,122 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Es ist noch notwendig die Z-Kalibrierung auszufuehren. Bitte befolgen Sie das Handbuch, Kapitel Erste Schritte, Abschnitt Kalibrierablauf."
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2863
 msgid "Total filament"
 msgstr "Gesamtes Filament"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2863
 msgid "Total print time"
 msgstr "Gesamte Druckzeit"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6633
 msgid "Tune"
 msgstr "Feineinstellung"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Unload"
 msgstr "Entladen"
 
 # 
-#: ultralcd.cpp:5617
-msgid "Unload all"
-msgstr "Alles entladen"
-
-# 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "Total failures"
-msgstr ""
+msgstr "Gesamte Fehler"
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2213
 msgid "to load filament"
-msgstr ""
+msgstr "zum Filament laden"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2217
 msgid "to unload filament"
-msgstr ""
+msgstr "zum Filament entladen"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Filament entladen"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Filament auswerfen"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1824
 msgid "Total"
-msgstr ""
+msgstr "Gesamt"
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5822
 msgid "Used during print"
 msgstr "Beim Druck benutzt"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2143
 msgid "Voltages"
 msgstr "Spannungen"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2116
 msgid "unknown"
-msgstr ""
+msgstr "unbekannt"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5262
 msgid "Wait for user..."
 msgstr "Warte auf Benutzer.."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3374
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Warten bis Heizung und Bett abgekuehlt sind"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3338
 msgid "Waiting for PINDA probe cooling"
 msgstr "Warten, bis PINDA- Sonde abgekuehlt ist"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4782
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Entladen Sie das Filament 1, wenn er aus dem hinteren MMU-Rohr herausragt. Verwenden Sie den Auswurf, wenn er im Rohr versteckt ist."
 
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1511
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Warnung: Druckertyp und Platinentyp wurden beide geaendert."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1503
 msgid "Warning: motherboard type changed."
 msgstr "Warnung: Platinentyp wurde geaendert."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1507
 msgid "Warning: printer type changed."
 msgstr "Warnung: Druckertyp wurde geaendert."
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3053
 msgid "Was filament unload successful?"
 msgstr "Konnten Sie das Filament entnehmen?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Verdrahtungsfehler"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5661
 msgid "Wizard"
 msgstr "Assistent"
 
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2132
 msgid "XYZ cal. details"
 msgstr "XYZ Kal. Details"
 
@@ -1641,107 +1496,317 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Bitte schauen Sie in das Handbuch."
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Ja"
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Sie koennen den Assistenten immer im Menu neu starten: Kalibrierung -> Assistent"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3838
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "XYZ Kalibrierung in Ordnung. Schraeglauf wird automatisch korrigiert."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "XYZ Kalibrierung in Ordnung. X/Y Achsen sind etwas schraeg."
 
 # 
-#: ultralcd.cpp:4885
-msgid "X-correct"
-msgstr "X-Korrektur"
+#: ultralcd.cpp:5044
+msgid "X-correct:"
+msgstr "X-Korrektur:"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3832
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "XYZ-Kalibrierung ok. X/Y-Achsen sind senkrecht zueinander Glueckwunsch!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "XYZ-Kalibrierung beeintraechtigt. Vordere Kalibrierpunkte nicht erreichbar."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3819
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "XYZ-Kalibrierung beeintraechtigt. Rechter vorderer Kalibrierpunkt nicht erreichbar."
 
-# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
-#: ultralcd.cpp:3699
-msgid "XYZ calibration compromised. Left front calibration point not reachable."
-msgstr "XYZ-Kalibrierung beeintraechtigt. Linker vorderer Kalibrierpunkt nicht erreichbar."
-
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6080
 msgid "Load all"
 msgstr "Alle laden"
 
-# MSG_LOAD_FILAMENT_1 c=17
-#: ultralcd.cpp:5576
-msgid "Load filament 1"
-msgstr "Filament 1 laden"
-
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3798
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Bett-Kalibrierpunkt nicht gefunden."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Vordere Kalibrierpunkte nicht erreichbar."
 
 # 
-#: ultralcd.cpp:3687
-msgid "XYZ calibration failed. Left front calibration point not reachable."
-msgstr "XYZ-Kalibrierung fehlgeschlagen. Linker vorderer Kalibrierpunkt nicht erreichbar."
-
-# MSG_LOAD_FILAMENT_2 c=17
-#: ultralcd.cpp:5577
-msgid "Load filament 2"
-msgstr "Filament 2 laden"
-
-# 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3807
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Rechter vorderer Kalibrierpunkt ist nicht erreichbar."
 
-# MSG_LOAD_FILAMENT_3 c=17
-#: ultralcd.cpp:5578
-msgid "Load filament 3"
-msgstr "Filament 3 laden"
+"XYZ calibration failed. Right front calibration point not reachable."
+#: 
+msgid "XYZ-Kalibrierung fehlgeschlagen. Rechter vorderer Kalibrierpunkt ist nicht erreichbar."
+msgstr 
 
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2968
 msgid "Y distance from min"
 msgstr "Y Entfernung vom Min"
 
 # 
-#: ultralcd.cpp:4886
-msgid "Y-correct"
-msgstr "Y-Korrektur"
+#: ultralcd.cpp:5045
+msgid "Y-correct:"
+msgstr "Y-Korrektur:"
 
-# MSG_LOAD_FILAMENT_4 c=17
-#: ultralcd.cpp:5579
-msgid "Load filament 4"
-msgstr "Filament 4 laden"
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr ""
+
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Zurueck"
+
+# 
+#: ultralcd.cpp:5553
+msgid "Checks"
+msgstr ""
+
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falschtriggerung"
+
+# 
+#: ultralcd.cpp:3946
+msgid "FINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5459
+msgid "Firmware   [none]"
+msgstr "Firmware   [ohne]"
+
+# 
+#: ultralcd.cpp:5465
+msgid "Firmware [strict]"
+msgstr "Firmware [streng]"
+
+# 
+#: ultralcd.cpp:5462
+msgid "Firmware   [warn]"
+msgstr ""
+
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "HW Einstellungen"
+
+# 
+#: ultralcd.cpp:3950
+msgid "IR:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Magnet Komp.  [nv]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Magnet Komp. [Aus]"
+
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Magnet Komp.  [An]"
+
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5591
+msgid "Mesh bed leveling"
+msgstr "Mesh Bett Ausgleich"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5220
+msgid "MMU Mode [Normal]"
+msgstr "MMU Modus[Normal]"
+
+# 
+#: ultralcd.cpp:5221
+msgid "MMU Mode[Stealth]"
+msgstr "MMU Mod.[Stealth]"
+
+# 
+#: ultralcd.cpp:4427
+msgid "Mode change in progress ..."
+msgstr "Moduswechsel erfolgt..."
+
+# 
+#: ultralcd.cpp:5420
+msgid "Model      [none]"
+msgstr "Modell     [ohne]"
+
+# 
+#: ultralcd.cpp:5426
+msgid "Model    [strict]"
+msgstr "Modell   [streng]"
+
+# 
+#: ultralcd.cpp:5423
+msgid "Model      [warn]"
+msgstr "Modell     [warn]"
+
+# 
+#: ultralcd.cpp:5381
+msgid "Nozzle d.  [0.25]"
+msgstr "Duese D.   [0.25]"
+
+# 
+#: ultralcd.cpp:5384
+msgid "Nozzle d.  [0.40]"
+msgstr "Duese D.   [0.40]"
+
+# 
+#: ultralcd.cpp:5387
+msgid "Nozzle d.  [0.60]"
+msgstr "Duese D.   [0.60]"
+
+# 
+#: ultralcd.cpp:5335
+msgid "Nozzle     [none]"
+msgstr "Duese      [ohne]"
+
+# 
+#: ultralcd.cpp:5341
+msgid "Nozzle   [strict]"
+msgstr "Duese    [streng]"
+
+# 
+#: ultralcd.cpp:5338
+msgid "Nozzle     [warn]"
+msgstr "Duese      [warn]"
+
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr ""
 
-# MSG_LOAD_FILAMENT_5 c=17
-#: ultralcd.cpp:5582
-msgid "Load filament 5"
-msgstr "Filament 5 laden"
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:3942
+msgid "PINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2286
+msgid "Preheating to cut"
+msgstr "Heizen zum Schnitt"
+
+# 
+#: ultralcd.cpp:2283
+msgid "Preheating to eject"
+msgstr "Heizen zum Auswurf"
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Der Durchmesser der Druckerduese weicht vom G-Code ab. Fortfahren?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Der Durchmesser der Druckerduese weicht vom G-Code ab. Bitte ueberpruefen Sie den Wert in den Einstellungen. Druck abgebrochen."
+
+# 
+#: ultralcd.cpp:6597
+msgid "Rename"
+msgstr "Umbenennen"
+
+# 
+#: ultralcd.cpp:6593
+msgid "Select"
+msgstr "Auswahl"
+
+# 
+#: ultralcd.cpp:2134
+msgid "Sensor info"
+msgstr "Sensor Info"
+
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Blech"
+
+# 
+#: 
+msgid "Sound     [assist]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5046
+msgid "Z-correct:"
+msgstr "Z-Korrektur:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Z-Probe Nr.    [1]"
 

lang/po/Firmware_es.po

@@ -7,8 +7,8 @@ msgstr ""
 "Content-Transfer-Encoding: 8bit\n"
 "Language: es\n"
 "Project-Id-Version: Prusa-Firmware\n"
-"POT-Creation-Date: čt 7. úno 2019 14:45:41\n"
-"PO-Revision-Date: čt 7. úno 2019 14:45:41\n"
+"POT-Creation-Date: Wed Sep 4 16:13:52 CEST 2019\n"
+"PO-Revision-Date: Wed Sep 4 16:13:52 CEST 2019\n"
 "Language-Team: \n"
 "X-Generator: Poedit 2.0.7\n"
 "X-Poedit-SourceCharset: UTF-8\n"
@@ -21,74 +21,74 @@ msgid " of 4"
 msgstr " de 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " de 9"
 
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3027
 msgid "[0;0] point offset"
 msgstr "[0;0] punto offset"
 
 # MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
-#: ultralcd.cpp:4219
-msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
-msgstr "\x1b[2JDec. choque\x1b[1;0Hpuede ser activada solo en\x1b[2;0HModo normal"
+#: 
+msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
+msgstr "Dec. choque puede\x0aser activada solo en\x0aModo normal"
 
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-#: ultralcd.cpp:4231
-msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
-msgstr "\x1b[2JATENCION:\x1b[1;0HDec. choque\x1b[2;0Hdesactivada en\x1b[3;0HModo silencio"
+#: 
+msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
+msgstr "ATENCION:\x0aDec. choque\x0adesactivada en\x0aModo silencio"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2290
 msgid ">Cancel"
-msgstr ""
+msgstr ">Cancelar"
 
-# MSG_BABYSTEPPING_Z c=20
-#: ultralcd.cpp:3043
-msgid "Adjusting Z"
-msgstr "Ajustar Z"
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3147
+msgid "Adjusting Z:"
+msgstr "Ajustar Z:"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Todo bien"
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Terminado! Feliz impresion!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1974
 msgid "Ambient"
-msgstr ""
+msgstr "Ambiente"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2576
 msgid "and press the knob"
 msgstr "Haz clic"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3445
 msgid "Are left and right Z~carriages all up?"
 msgstr "Carros Z izq./der. estan arriba maximo?"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5114
 msgid "SpoolJoin    [on]"
-msgstr "SpoolJoin    [on]"
+msgstr ""
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5110
 msgid "SpoolJoin   [N/A]"
-msgstr "SpoolJoin   [N/A]"
+msgstr ""
 
-#  MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+# MSG_AUTO_DEPLETE_OFF c=17 r=1
+#: ultralcd.cpp:5118
 msgid "SpoolJoin   [off]"
-msgstr "SpoolJoin   [off]"
+msgstr ""
 
 # MSG_AUTO_HOME
 #: messages.c:11
@@ -96,32 +96,32 @@ msgid "Auto home"
 msgstr "Llevar al origen"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6736
 msgid "AutoLoad filament"
 msgstr "Carga automatica de filamento"
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4378
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "La carga automatica de filamento solo funciona si el sensor de filamento esta activado..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2771
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "La carga automatica de filamento esta activada, pulse el dial e inserte el filamento..."
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Longitud del eje"
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Eje"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Base / Calentador"
 
@@ -136,7 +136,7 @@ msgid "Bed Heating"
 msgstr "Calentando Base"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5682
 msgid "Bed level correct"
 msgstr "Corr. de la cama"
 
@@ -145,38 +145,28 @@ msgstr "Corr. de la cama"
 msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
 msgstr "Nivelacion fallada. Sensor no funciona. Restos en boquilla? Esperando reset."
 
-# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
-#: Marlin_main.cpp:4508
-msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
-msgstr "Nivelacion fallada. Sensor desconectado o cables danados. Esperando reset."
-
-# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
-#: Marlin_main.cpp:4512
-msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
-msgstr "Nivelacion fallada. Sensor funciona demasiado pronto. Esperando reset."
-
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Base calefactable "
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2002
 msgid "Belt status"
 msgstr "Estado de la correa"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Se fue la luz. ?Reanudar la impresion?"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
-msgstr ""
+msgstr "Calibrando posicion inicial"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5671
 msgid "Calibrate XYZ"
 msgstr "Calibrar XYZ"
 
@@ -186,12 +176,12 @@ msgid "Calibrate Z"
 msgstr "Calibrar Z"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4570
 msgid "Calibrate"
 msgstr "Calibrar"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrando XYZ. Gira el dial para subir el extrusor hasta tocar los topes superiores. Despues haz clic."
 
@@ -201,37 +191,32 @@ msgid "Calibrating Z"
 msgstr "Calibrando Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrando Z. Gira el dial para subir el extrusor hasta tocar los topes superiores. Despues haz clic."
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:813
 msgid "Calibration done"
 msgstr "Calibracion OK"
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Calibracion"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Cancel"
 msgstr "Cancelar"
 
-# MSG_SD_INSERTED
-#: 
-msgid "Card inserted"
-msgstr "Tarjeta insertada"
-
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Tarjeta retirada"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2676
 msgid "Color not correct"
 msgstr "Color no homogeneo"
 
@@ -241,7 +226,7 @@ msgid "Cooldown"
 msgstr "Enfriar"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4503
 msgid "Copy selected language?"
 msgstr "Copiar idioma seleccionado?"
 
@@ -266,27 +251,27 @@ msgid "Crash detected."
 msgstr "Choque detectado."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:600
 msgid "Crash detected. Resume print?"
 msgstr "Choque detectado. Continuar impresion?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Crash"
-msgstr ""
+msgstr "Choque"
 
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5823
 msgid "Current"
 msgstr "Actual"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2102
 msgid "Date:"
 msgstr "Fecha:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5568
 msgid "Disable steppers"
 msgstr "Apagar motores"
 
@@ -296,77 +281,52 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Distancia entre la punta del boquilla y la superficie de la base aun no fijada. Por favor siga el manual, capitulo Primeros Pasos, Calibracion primera capa."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4984
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Quieres repetir el ultimo paso para reajustar la distancia boquilla-base?"
 
-# MSG_EXTRUDER_CORRECTION c=9
-#: ultralcd.cpp:4889
-msgid "E-correct"
-msgstr "E-correcion"
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5048
+msgid "E-correct:"
+msgstr "E-correcion:"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Expulsar filamento"
 
-# MSG_EJECT_FILAMENT1 c=17 r=1
-#: ultralcd.cpp:5603
-msgid "Eject filament 1"
-msgstr "Expulsar filamento 1"
-
-# MSG_EJECT_FILAMENT2 c=17 r=1
-#: ultralcd.cpp:5604
-msgid "Eject filament 2"
-msgstr "Expulsar filamento 2"
-
-# MSG_EJECT_FILAMENT3 c=17 r=1
-#: ultralcd.cpp:5605
-msgid "Eject filament 3"
-msgstr "Expulsar filamento 3"
-
-# MSG_EJECT_FILAMENT4 c=17 r=1
-#: ultralcd.cpp:5606
-msgid "Eject filament 4"
-msgstr "Expulsar filamento 4"
-
-# MSG_EJECT_FILAMENT5 c=17 r=1
-#: ultralcd.cpp:5607
-msgid "Eject filament 5"
-msgstr "Expulsar filamento 5"
-
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Eject"
 msgstr "Expulsar"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1434
 msgid "Ejecting filament"
 msgstr "Expulsando filamento"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Endstop no alcanzado"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr ""
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr ""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Error - se ha sobre-escrito la memoria estatica"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4391
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "ERROR: El sensor de filamento no responde, por favor comprueba la conexion."
 
@@ -375,38 +335,13 @@ msgstr "ERROR: El sensor de filamento no responde, por favor comprueba la conexi
 msgid "ERROR:"
 msgstr ""
 
-# 
-#: Marlin_main.cpp:1006
-msgid "External SPI flash W25X20CL not responding."
-msgstr "No responde el flasheo externo SPI W25X20CL"
-
-# 
-#: ultralcd.cpp:5633
-msgid "Extruder 1"
-msgstr "Extrusor 1"
-
-# 
-#: ultralcd.cpp:5634
-msgid "Extruder 2"
-msgstr "Extrusor 2"
-
-# 
-#: ultralcd.cpp:5635
-msgid "Extruder 3"
-msgstr "Extrusor 3"
-
-# 
-#: ultralcd.cpp:5636
-msgid "Extruder 4"
-msgstr "Extrusor 4"
-
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Ventilador del extrusor:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2133
 msgid "Extruder info"
 msgstr "Informacion del extrusor"
 
@@ -416,12 +351,12 @@ msgid "Extruder"
 msgstr "Extruir"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
-msgstr ""
+msgstr "Estadistica de fallos MMU"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5082
 msgid "F. autoload  [on]"
 msgstr "Autocarg.Fil[act]"
 
@@ -431,14 +366,14 @@ msgid "F. autoload [N/A]"
 msgstr "Autocarg.Fil[N/D]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5084
 msgid "F. autoload [off]"
 msgstr "Autocarg.Fil[ina]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
-msgstr ""
+msgstr "Estadistica de fallos"
 
 # MSG_FAN_SPEED c=14
 #: messages.c:31
@@ -446,17 +381,17 @@ msgid "Fan speed"
 msgstr "Velocidad Vent."
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventiladores"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5577
 msgid "Fans check   [on]"
 msgstr "Comprob.vent[act]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5579
 msgid "Fans check  [off]"
 msgstr "Comprob.vent[ina]"
 
@@ -465,13 +400,8 @@ msgstr "Comprob.vent[ina]"
 msgid "Fil. sensor  [on]"
 msgstr "Sensor Fil. [act]"
 
-# MSG_RESPONSE_POOR c=20 r=2
-#: Marlin_main.cpp:3146
-msgid "Fil. sensor response is poor, disable it?"
-msgstr "La respuesta del sensor de fil es deficiente, ?desactivarlo?"
-
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5062
 msgid "Fil. sensor [N/A]"
 msgstr "Sensor Fil. [N/D]"
 
@@ -481,9 +411,9 @@ msgid "Fil. sensor [off]"
 msgstr "Sensor Fil. [ina]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Filam. runouts"
-msgstr ""
+msgstr "Filam. acabado"
 
 # MSG_FILAMENT_CLEAN c=20 r=2
 #: messages.c:32
@@ -491,32 +421,27 @@ msgid "Filament extruding & with correct color?"
 msgstr "Es nitido el color nuevo?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2672
 msgid "Filament not loaded"
 msgstr "Fil. no introducido"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Sensor de filamento"
 
-# MSG_SELFTEST_FILAMENT_SENSOR c=18
-#: ultralcd.cpp:7477
-msgid "Filament sensor:"
-msgstr "Sensor de filamento:"
-
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2841
 msgid "Filament used"
 msgstr "Filamento usado"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2841
 msgid "Print time"
 msgstr "Tiempo de imp.:"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Archivo incompleto. ?Continuar de todos modos?"
 
@@ -526,52 +451,52 @@ msgid "Finishing movements"
 msgstr "Term. movimientos"
 
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Cal. primera cap."
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4896
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Primero, hare el Selftest para comprobar los problemas de montaje mas comunes."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Corrige el problema y pulsa el boton en la unidad MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Flujo"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2095
 msgid "forum.prusa3d.com"
 msgstr ""
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Vent. frontal?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3220
 msgid "Front side[um]"
 msgstr "Frontal [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Ventiladores frontal/izquierdo"
 
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Calentador/Termistor"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8468
 msgid "Heating disabled by safety timer."
 msgstr "Calentadores desactivados por el temporizador de seguridad."
 
@@ -586,67 +511,62 @@ msgid "Heating"
 msgstr "Calentando..."
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4875
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Hola, soy tu impresora Original Prusa i3. Quieres que te guie a traves de la configuracion?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2096
 msgid "howto.prusa3d.com"
 msgstr ""
 
-# 
-#: ultralcd.cpp:6087
-msgid "Change extruder"
-msgstr "Cambiar extrusor."
-
 # MSG_FILAMENTCHANGE
 #: messages.c:37
 msgid "Change filament"
 msgstr "Cambiar filamento"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2587
 msgid "Change success!"
 msgstr "Cambio correcto"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2664
 msgid "Changed correctly?"
 msgstr "Cambio correcto?"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Control base cal."
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Control endstops"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Control fusor"
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Comprobando los sensores"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Control sensor X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Control sensor Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Control sensor Z"
 
@@ -666,112 +586,82 @@ msgid "Filament"
 msgstr "Filamento"
 
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4905
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Hare la calibracion XYZ. Tardara 12 min. aproximadamente."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4913
 msgid "I will run z calibration now."
 msgstr "Voy a hacer Calibracion Z ahora."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4978
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Voy a comenzar a imprimir la linea y tu bajaras el nozzle gradualmente al rotar el dial, hasta que llegues a la altura optima. Mira las imagenes del capitulo Calibracion en el manual."
 
-# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
-#: mesh_bed_calibration.cpp:2481
-msgid "Improving bed calibration point"
-msgstr "Mejorando punto de calibracion base"
-
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Monitorizar"
 
-# MSG_FILAMENT_LOADING_T0 c=20 r=4
-#: messages.c:33
-msgid "Insert filament into extruder 1. Click when done."
-msgstr "Insertar filamento en el extrusor 1. Haz clic una vez terminado."
-
-# MSG_FILAMENT_LOADING_T1 c=20 r=4
-#: messages.c:34
-msgid "Insert filament into extruder 2. Click when done."
-msgstr "Insertar filamento en el extrusor 2. Haz clic una vez terminado."
-
-# MSG_FILAMENT_LOADING_T2 c=20 r=4
-#: messages.c:35
-msgid "Insert filament into extruder 3. Click when done."
-msgstr "Insertar filamento en el extrusor 3. Haz clic una vez terminado."
-
-# MSG_FILAMENT_LOADING_T3 c=20 r=4
-#: messages.c:36
-msgid "Insert filament into extruder 4. Click when done."
-msgstr "Insertar filamento en el extrusor 4. Haz clic una vez terminado."
-
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:4938
 msgid "Is filament 1 loaded?"
 msgstr "?Esta cargado el filamento 1?"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2572
 msgid "Insert filament"
 msgstr "Introducir filamento"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4941
 msgid "Is filament loaded?"
 msgstr "Esta el filamento cargado?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4972
 msgid "Is it PLA filament?"
 msgstr "Es el filamento PLA?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4704
 msgid "Is PLA filament loaded?"
 msgstr "Esta el filamento PLA cargado?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "?Esta colocada la lamina de acero sobre la base?"
 
-# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
-#: mesh_bed_calibration.cpp:2223
-msgid "Iteration "
-msgstr "Reiteracion "
-
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1840
 msgid "Last print failures"
-msgstr ""
+msgstr "Ultimas impresiones fallidas"
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1823
 msgid "Last print"
-msgstr ""
+msgstr "Ultima impresion"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Vent. izquierdo?"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2970
 msgid "Left"
 msgstr "Izquierda"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3218
 msgid "Left side [um]"
 msgstr "Izquierda [um]"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5594
 msgid "Lin. correction"
 msgstr "Correccion de Linealidad"
 
@@ -786,7 +676,7 @@ msgid "Load filament"
 msgstr "Introducir filam."
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2612
 msgid "Loading color"
 msgstr "Cambiando color"
 
@@ -796,92 +686,92 @@ msgid "Loading filament"
 msgstr "Introduciendo filam."
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Polea suelta"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6719
 msgid "Load to nozzle"
 msgstr "Cargar a la boquilla"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Cal. primera cap."
 
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Menu principal"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Midiendo altura del punto de calibracion"
 
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5677
 msgid "Mesh Bed Leveling"
 msgstr "Nivelacion Mesh Level"
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Restaurando posicion..."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Restaurando temperatura..."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3005
 msgid "Measured skew"
 msgstr "Desviacion medida:"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU fails"
-msgstr ""
+msgstr "Fallos MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1613
 msgid "MMU load failed     "
-msgstr ""
+msgstr "Carga MMU fallida"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU load fails"
-msgstr ""
+msgstr "Carga MMU falla"
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Resumiendo..."
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Modo     [Normal]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Modo   [silencio]"
 
 # 
-#: mmu.cpp:635
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU necesita atencion del usuario."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "MMU power fails"
-msgstr ""
+msgstr "Fallo de energia en MMU"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Modo   [Silencio]"
 
@@ -891,62 +781,62 @@ msgid "Mode [auto power]"
 msgstr "Modo[fuerza auto]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Modo [rend.pleno]"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2108
 msgid "MMU2 connected"
-msgstr ""
+msgstr "MMU2 conectado"
 
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr ""
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5566
 msgid "Move axis"
 msgstr "Mover ejes"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4294
 msgid "Move X"
 msgstr "Mover X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4295
 msgid "Move Y"
 msgstr "Mover Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4296
 msgid "Move Z"
 msgstr "Mover Z"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5291
 msgid "No move."
 msgstr "Sin movimiento"
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6686
 msgid "No SD card"
 msgstr "No hay tarjeta SD"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2976
 msgid "N/A"
-msgstr ""
+msgstr "No disponible"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr ""
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "No hay conexion "
 
@@ -955,78 +845,73 @@ msgstr "No hay conexion "
 msgid "New firmware version available:"
 msgstr "Nuevo firmware disponible:"
 
-# 
-#: 
-msgid "No "
-msgstr "No"
-
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Ventilador no gira"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4977
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Voy a calibrar la distancia entre la punta de la boquilla y la superficie de la base."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4921
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Voy a precalentar la boquilla para PLA ahora."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Boquilla"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1519
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Se han encontrado ajustes anteriores. Se ajustara el PID, los pasos del extrusor, etc"
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4912
 msgid "Now remove the test print from steel sheet."
 msgstr "Ahora retira la prueba de la lamina de acero."
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:1782
 msgid "Nozzle FAN"
-msgstr ""
+msgstr "Ventilador de capa"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6649
 msgid "Pause print"
 msgstr "Pausar impresion"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1598
 msgid "PID cal.           "
 msgstr "Cal. PID "
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1604
 msgid "PID cal. finished"
 msgstr "Cal. PID terminada"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5683
 msgid "PID calibration"
 msgstr "Calibracion PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:843
 msgid "PINDA Heating"
 msgstr "Calentando PINDA"
 
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Colocar una hoja de papel sobre la superficie de impresion durante la calibracion de los primeros 4 puntos. Si la boquilla mueve el papel, apagar impresora inmediatamente."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4986
 msgid "Please clean heatbed and then press the knob."
 msgstr "Limpia la superficie de la base, por favor, y haz clic"
 
@@ -1036,92 +921,92 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Limpia boquilla para calibracion. Click cuando acabes."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Controla :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Lee el manual y resuelve el problema. Despues, reinicia la impresora y continua con el Wizard"
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4808
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Inserta, por favor, filamento PLA en el extrusor. Despues haz clic para cargarlo."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4709
 msgid "Please load PLA filament first."
 msgstr "Carga el filamento PLA primero por favor."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3063
 msgid "Please open idler and remove filament manually."
 msgstr "Por favor abate el rodillo de empuje (idler) y retira el filamento manualmente."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Por favor coloca la chapa de acero en la base calefactable."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Por favor, pulsa el dial para descargar el filamento"
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4803
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Por favor introduce el filamento al primer tubo MMU, despues presiona el dial para imprimirlo."
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Por favor retire el filamento de inmediato"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1440
 msgid "Please remove filament and then press the knob."
 msgstr "Por favor quite el filamento y luego presione el dial."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Por favor retire la chapa de acero de la base calefactable."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4354
 msgid "Please run XYZ calibration first."
 msgstr "Por favor realiza la calibracion XYZ primero."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1359
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Por favor actualice el firmware en tu MMU2. Esperando el reseteo."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Por Favor Espere"
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4911
 msgid "Please remove shipping helpers first."
 msgstr "Por favor retira los soportes de envio primero."
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Precalienta extrusor!"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6636
 msgid "Preheat"
 msgstr "Precalentar"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Precalentando nozzle. Espera por favor."
 
@@ -1131,32 +1016,32 @@ msgid "Please upgrade."
 msgstr "Actualize por favor"
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10365
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Pulsa el dial para precalentar la boquilla y continue."
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Power failures"
-msgstr ""
+msgstr "Cortes de energia"
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Impresion cancelada"
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2276
 msgid "Preheating to load"
-msgstr ""
+msgstr "Precalentar para cargar"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2280
 msgid "Preheating to unload"
-msgstr ""
+msgstr "Precalentar para descargar"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Ventilador del fusor:"
 
@@ -1166,17 +1051,17 @@ msgid "Print from SD"
 msgstr "Menu tarjeta SD"
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2206
 msgid "Press the knob"
-msgstr ""
+msgstr "Pulsa el dial"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1061
 msgid "Print paused"
 msgstr "Impresion en pausa"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Presiona el dial para continuar con la temperatura de la boquilla."
 
@@ -1186,37 +1071,27 @@ msgid "Printer has not been calibrated yet. Please follow the manual, chapter Fi
 msgstr "Impresora no esta calibrada todavia. Por favor usa el manual capitulo Primeros pasos Calibracion flujo."
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1784
 msgid "Print FAN"
-msgstr ""
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK2.5 ready."
-msgstr "Preparado para Prusa i3 MK2.5."
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK3 ready."
-msgstr "Prusa i3 MK3 prep."
+msgstr "Ventilador del extrusor"
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2094
 msgid "prusa3d.com"
 msgstr "prusa3d.es"
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3221
 msgid "Rear side [um]"
 msgstr "Trasera [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9765
 msgid "Recovering print    "
 msgstr "Recuperando impresion"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Retire el filamento viejo y presione el dial para comenzar a cargar el nuevo filamento."
 
@@ -1225,63 +1100,58 @@ msgstr "Retire el filamento viejo y presione el dial para comenzar a cargar el n
 msgid "Prusa i3 MK3S OK."
 msgstr ""
 
-# 
-#: 
-msgid "Prusa i3 MK2 ready."
-msgstr "Preparado para i3 MK2."
-
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5688
 msgid "Reset XYZ calibr."
 msgstr ""
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3222
 msgid "Reset"
 msgstr ""
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6656
 msgid "Resume print"
 msgstr "Reanudar impres."
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Resumiendo impresion"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3219
 msgid "Right side[um]"
 msgstr "Derecha [um]"
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5606
 msgid "RPi port     [on]"
 msgstr "Puerto RPi  [act]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5604
 msgid "RPi port    [off]"
 msgstr "Puerto RPi  [ina]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4726
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Ejecutar el Wizard borrara los valores de calibracion actuales y comenzara de nuevo. Continuar?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5236
 msgid "SD card  [normal]"
 msgstr "Tarj. SD [normal]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5234
 msgid "SD card [flshAir]"
 msgstr "Tarj. SD[FlshAir]"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2971
 msgid "Right"
 msgstr "Derecha"
 
@@ -1291,217 +1161,207 @@ msgid "Searching bed calibration point"
 msgstr "Buscando punto de calibracion base"
 
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5613
 msgid "Select language"
 msgstr "Cambiar el idioma"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr ""
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Iniciar Selftest"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5664
 msgid "Selftest         "
 msgstr "Selftest"
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Error Selftest !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Fallo Selftest"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1551
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Se realizara el auto-test para calibrar con precision la vuelta a la posicion inicial sin sensores."
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4959
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Selecciona la temperatura para precalentar la boquilla que se ajuste a tu material. "
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Select PLA filament:"
 msgstr "Seleccionar filamento PLA:"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3230
 msgid "Set temperature:"
 msgstr "Establecer temp.:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Configuracion"
 
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5685
 msgid "Show end stops"
 msgstr "Mostrar endstops"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:3941
 msgid "Sensor state"
-msgstr ""
-
-# 
-#: 
-msgid "Sensors info"
-msgstr ""
-
-# 
-#: 
-msgid "Show pinda state"
-msgstr "Mostrar estado pinda"
+msgstr "Estado del sensor"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Algunos archivos no se ordenaran. Maximo 100 archivos por carpeta para ordenar. "
 
 # MSG_SORT_NONE c=17 r=1
-#: ultralcd.cpp:5043
-msgid "Sort:      [none]"
-msgstr "Ordenar:   [nada]"
+#: ultralcd.cpp:5246
+msgid "Sort       [none]"
+msgstr "Ordenar    [nada]"
 
 # MSG_SORT_TIME c=17 r=1
-#: ultralcd.cpp:5041
-msgid "Sort:      [time]"
-msgstr "Orden:    [Fecha]"
+#: ultralcd.cpp:5244
+msgid "Sort       [time]"
+msgstr "Ordenar   [Fecha]"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3008
 msgid "Severe skew"
 msgstr "Inclinacion severa"
 
 # MSG_SORT_ALPHA c=17 r=1
-#: ultralcd.cpp:5042
-msgid "Sort:  [alphabet]"
-msgstr "Ordenar:[alfabet]"
+#: ultralcd.cpp:5245
+msgid "Sort   [alphabet]"
+msgstr "Ordenar [alfabet]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Ordenando archivos"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Sonido     [alto]"
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3007
 msgid "Slight skew"
 msgstr "Ligeramente inclinado"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#: 
 msgid "Sound      [mute]"
 msgstr "Sonido[silenciad]"
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4870
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Problema encontrado, nivelacion Z forzosa ..."
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Sonido  [una vez]"
 
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Sonido[silencios]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Velocidad"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Ventilador girando"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4367
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Se necesita una temperatura ambiente ente 21 y 26C y un soporte rigido."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Estadisticas "
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Detener impresion"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "PARADA"
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Soporte"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Intercambiado"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Cal. temp. "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5600
 msgid "Temp. cal.   [on]"
 msgstr "Cal. temp.   [ON]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5598
 msgid "Temp. cal.  [off]"
 msgstr "Cal. temp.  [OFF]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5694
 msgid "Temp. calibration"
 msgstr "Calibracion temp."
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3867
 msgid "Temperature calibration failed"
 msgstr "Fallo de la calibracion de temperatura"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Calibracion temperatura terminada. Haz clic para continuar."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5564
 msgid "Temperature"
 msgstr "Temperatura"
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2140
 msgid "Temperatures"
 msgstr "Temperaturas"
 
@@ -1511,127 +1371,122 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Todavia es necesario hacer una calibracion Z. Por favor siga el manual, capitulo Primeros pasos, seccion Calibracion del flujo."
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2863
 msgid "Total filament"
 msgstr "Filamento total:"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2863
 msgid "Total print time"
 msgstr "Tiempo total :"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6633
 msgid "Tune"
 msgstr "Ajustar"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Unload"
 msgstr "Descargar"
 
 # 
-#: ultralcd.cpp:5617
-msgid "Unload all"
-msgstr "Soltar todos fil."
-
-# 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "Total failures"
-msgstr ""
+msgstr "Fallos totales"
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2213
 msgid "to load filament"
-msgstr ""
+msgstr "para cargar el filamento"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2217
 msgid "to unload filament"
-msgstr ""
+msgstr "para descargar el filamento"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Soltar filamento"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Soltando filamento"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1824
 msgid "Total"
 msgstr ""
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5822
 msgid "Used during print"
 msgstr "Usado en impresion"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2143
 msgid "Voltages"
 msgstr "Voltajes"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2116
 msgid "unknown"
-msgstr ""
+msgstr "desconocido"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5262
 msgid "Wait for user..."
 msgstr "Esperando ordenes"
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3374
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Esperando enfriamiento de la base y extrusor."
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3338
 msgid "Waiting for PINDA probe cooling"
 msgstr "Esperando a que se enfrie la sonda PINDA"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4782
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Usa unload para retirar el filamento 1 si sobresale por fuera de la parte trasera del tubo MMU. Usa Expulsar si esta escondido dentro del tubo"
 
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1511
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Aviso: tanto el tipo de impresora como el tipo de la placa han cambiado."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1503
 msgid "Warning: motherboard type changed."
 msgstr "Cuidado: el tipo de placa ha cambiado."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1507
 msgid "Warning: printer type changed."
 msgstr "Cuidado: Ha cambiado el tipo de impresora."
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3053
 msgid "Was filament unload successful?"
 msgstr "?Se cargocon exito el filamento?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Error de conexion"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5661
 msgid "Wizard"
 msgstr ""
 
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2132
 msgid "XYZ cal. details"
 msgstr "Detalles de calibracion XYZ"
 
@@ -1641,107 +1496,312 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Calibracion XYZ fallada. Consulta el manual por favor."
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Si"
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Siempre puedes acceder al asistente desde Calibracion -> Wizard"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3838
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Calibracion XYZ correcta. La inclinacion se corregira automaticamente."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Calibracion XYZ correcta. Los ejes X / Y estan ligeramente inclinados. Buen trabajo!"
 
 # 
-#: ultralcd.cpp:4885
-msgid "X-correct"
-msgstr "X-correcion"
+#: ultralcd.cpp:5044
+msgid "X-correct:"
+msgstr "X-correcion:"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3832
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Calibracion XYZ ok. Ejes X/Y perpendiculares. Enhorabuena!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Calibrazion XYZ comprometida. Puntos frontales no alcanzables."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3819
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Calibrazion XYZ comprometida. Punto frontal derecho no alcanzable."
 
-# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
-#: ultralcd.cpp:3699
-msgid "XYZ calibration compromised. Left front calibration point not reachable."
-msgstr "Calibrazion XYZ comprometida. Punto frontal izquierdo no alcanzable."
-
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6080
 msgid "Load all"
 msgstr "Intr. todos fil."
 
-# MSG_LOAD_FILAMENT_1 c=17
-#: ultralcd.cpp:5576
-msgid "Load filament 1"
-msgstr "Introducir fil. 1"
-
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3798
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Calibracion XYZ fallada. Puntos de calibracion en la base no encontrados."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Calibracion XYZ fallada. Puntos frontales no alcanzables."
 
 # 
-#: ultralcd.cpp:3687
-msgid "XYZ calibration failed. Left front calibration point not reachable."
-msgstr "Calibracion XYZ fallada. Punto frontal izquierdo no alcanzable."
-
-# MSG_LOAD_FILAMENT_2 c=17
-#: ultralcd.cpp:5577
-msgid "Load filament 2"
-msgstr "Introducir fil. 2"
-
-# 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3807
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Calibracion XYZ fallad. Punto frontal derecho no alcanzable."
 
-# MSG_LOAD_FILAMENT_3 c=17
-#: ultralcd.cpp:5578
-msgid "Load filament 3"
-msgstr "Introducir fil. 3"
-
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2968
 msgid "Y distance from min"
 msgstr "Distancia en Y desde el min"
 
 # 
-#: ultralcd.cpp:4886
-msgid "Y-correct"
-msgstr "Y-correcion"
+#: ultralcd.cpp:5045
+msgid "Y-correct:"
+msgstr "Y-correcion:"
 
-# MSG_LOAD_FILAMENT_4 c=17
-#: ultralcd.cpp:5579
-msgid "Load filament 4"
-msgstr "Introducir fil. 4"
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr ""
+
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "atras"
+
+# 
+#: ultralcd.cpp:5553
+msgid "Checks"
+msgstr "Comprobaciones"
+
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falsa activacion"
+
+# 
+#: ultralcd.cpp:3946
+msgid "FINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5459
+msgid "Firmware   [none]"
+msgstr "Firmware[ninguno]"
+
+# 
+#: ultralcd.cpp:5465
+msgid "Firmware [strict]"
+msgstr "Firmware[estrict]"
+
+# 
+#: ultralcd.cpp:5462
+msgid "Firmware   [warn]"
+msgstr "Firmware  [aviso]"
+
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "Configuracion HW"
+
+# 
+#: ultralcd.cpp:3950
+msgid "IR:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Comp. imanes [N/A]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Comp. imanes [Off]"
+
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Comp. imanes  [On]"
+
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Malla        [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Malla        [7x7]"
+
+# 
+#: ultralcd.cpp:5591
+msgid "Mesh bed leveling"
+msgstr "Nivelacion Malla Base"
 
-# MSG_LOAD_FILAMENT_5 c=17
-#: ultralcd.cpp:5582
-msgid "Load filament 5"
-msgstr "Cargar filamento 5"
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5220
+msgid "MMU Mode [Normal]"
+msgstr "Modo MMU [Normal]"
+
+# 
+#: ultralcd.cpp:5221
+msgid "MMU Mode[Stealth]"
+msgstr "Modo MMU[Silenci]"
+
+# 
+#: ultralcd.cpp:4427
+msgid "Mode change in progress ..."
+msgstr "Cambio de modo progresando ..."
+
+# 
+#: ultralcd.cpp:5420
+msgid "Model      [none]"
+msgstr "Modelo  [ninguno]"
+
+# 
+#: ultralcd.cpp:5426
+msgid "Model    [strict]"
+msgstr "Modelo [estricto]"
+
+# 
+#: ultralcd.cpp:5423
+msgid "Model      [warn]"
+msgstr "Modelo    [aviso]"
+
+# 
+#: ultralcd.cpp:5381
+msgid "Nozzle d.  [0.25]"
+msgstr "Diam. nozzl[0.25]"
+
+# 
+#: ultralcd.cpp:5384
+msgid "Nozzle d.  [0.40]"
+msgstr "Diam. nozzl[0.40]"
+
+# 
+#: ultralcd.cpp:5387
+msgid "Nozzle d.  [0.60]"
+msgstr "Diam. nozzl[0.60]"
+
+# 
+#: ultralcd.cpp:5335
+msgid "Nozzle     [none]"
+msgstr "Nozzle  [ninguno]"
+
+# 
+#: ultralcd.cpp:5341
+msgid "Nozzle   [strict]"
+msgstr "Nozzle [estricto]"
+
+# 
+#: ultralcd.cpp:5338
+msgid "Nozzle     [warn]"
+msgstr "Nozzle    [aviso]"
+
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:3942
+msgid "PINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2286
+msgid "Preheating to cut"
+msgstr "Precalentando para laminar"
+
+# 
+#: ultralcd.cpp:2283
+msgid "Preheating to eject"
+msgstr "Precalentar para expulsar"
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Diametro nozzle impresora difiere de cod.G. ?Continuar?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Diametro nozzle Impresora difiere de cod.G. Comprueba los valores en ajustes. Impresion cancelada."
+
+# 
+#: ultralcd.cpp:6597
+msgid "Rename"
+msgstr "Renombrar"
+
+# 
+#: ultralcd.cpp:6593
+msgid "Select"
+msgstr "Seleccionar"
+
+# 
+#: ultralcd.cpp:2134
+msgid "Sensor info"
+msgstr "Info sensor"
+
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Lamina"
+
+# 
+#: 
+msgid "Sound     [assist]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5046
+msgid "Z-correct:"
+msgstr "Correccion-Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Z-sensor nr.   [1]"
 

lang/po/Firmware_fr.po

@@ -7,8 +7,8 @@ msgstr ""
 "Content-Transfer-Encoding: 8bit\n"
 "Language: fr\n"
 "Project-Id-Version: Prusa-Firmware\n"
-"POT-Creation-Date: �t 7. úno 2019 14:47:01\n"
-"PO-Revision-Date: �t 7. úno 2019 14:47:01\n"
+"POT-Creation-Date: Wed Sep 4 16:13:59 CEST 2019\n"
+"PO-Revision-Date: Wed Sep 4 16:13:59 CEST 2019\n"
 "Language-Team: \n"
 "X-Generator: Poedit 2.0.7\n"
 "X-Poedit-SourceCharset: UTF-8\n"
@@ -21,74 +21,74 @@ msgid " of 4"
 msgstr "de 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr "de 9"
 
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3027
 msgid "[0;0] point offset"
 msgstr "Offset point [0;0]"
 
 # MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
-#: ultralcd.cpp:4219
-msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
-msgstr "\x1b[2JLa detection de crash\x1b[1;0Hpeut etre active\x1b[2;0Hqu'en mode Normal"
+#: 
+msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
+msgstr "La detection de\x0acrash peut etre\x0aactive seulement en\x0amode Normal"
 
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-#: ultralcd.cpp:4231
-msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
-msgstr "\x1b[2JATTENTION :\x1b[1;0H Detection de crash\x1b[2;0H desactivee en mode\x1b[3;0H Furtif"
+#: 
+msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
+msgstr "ATTENTION:\x0aDetection de crash\x0adesactivee en\x0amode Furtif"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2290
 msgid ">Cancel"
-msgstr ""
+msgstr ">Annuler"
 
-# MSG_BABYSTEPPING_Z c=20
-#: ultralcd.cpp:3043
-msgid "Adjusting Z"
-msgstr "Ajustement de Z"
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3147
+msgid "Adjusting Z:"
+msgstr "Ajust. de Z:"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Tout est correct"
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
-msgstr "Tout est termine. Bonne impression !"
+msgstr "Tout est pret. Bonne impression !"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1974
 msgid "Ambient"
 msgstr "Ambiant"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2576
 msgid "and press the knob"
 msgstr "et pressez le bouton"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3445
 msgid "Are left and right Z~carriages all up?"
-msgstr "Chariots Z gauche et droite tout en haut?"
+msgstr "Z~carriages gauche + droite tout en haut?"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5114
 msgid "SpoolJoin    [on]"
-msgstr "SpoolJoin    [on]"
+msgstr ""
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5110
 msgid "SpoolJoin   [N/A]"
-msgstr "SpoolJoin   [N/A]"
+msgstr ""
 
-#  MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+# MSG_AUTO_DEPLETE_OFF c=17 r=1
+#: ultralcd.cpp:5118
 msgid "SpoolJoin   [off]"
-msgstr "SpoolJoin   [off]"
+msgstr ""
 
 # MSG_AUTO_HOME
 #: messages.c:11
@@ -96,39 +96,39 @@ msgid "Auto home"
 msgstr "Mise a 0 des axes"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6736
 msgid "AutoLoad filament"
 msgstr "AutoCharge du filament"
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4378
 msgid "Autoloading filament available only when filament sensor is turned on..."
-msgstr "AutoCharge du filament uniquement si le capteur de filament est active."
+msgstr "Chargement auto du filament uniquement si le capteur de filament est active."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2771
 msgid "Autoloading filament is active, just press the knob and insert filament..."
-msgstr "AutoCharge actif, appuyez sur le bouton et inserez le filament."
+msgstr "Chargement auto du filament actif, appuyez sur le btn et inserez le fil."
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Longueur de l'axe"
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Axe"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Lit / Chauffage"
 
 # MSG_BED_DONE
 #: messages.c:16
 msgid "Bed done"
-msgstr "Lit termine"
+msgstr "Plateau termine"
 
 # MSG_BED_HEATING
 #: messages.c:17
@@ -136,24 +136,14 @@ msgid "Bed Heating"
 msgstr "Chauffe du lit"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5682
 msgid "Bed level correct"
-msgstr "Cor courbure du lit"
+msgstr "Corr. niveau plateau"
 
 # MSG_BED_LEVELING_FAILED_POINT_LOW c=20 r=4
 #: messages.c:18
 msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
-msgstr "Echec du nivellement. Capt. non declenche. Debris sur buse ? En attente d'un reset."
-
-# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
-#: Marlin_main.cpp:4508
-msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
-msgstr "Echec du nivellement. Capteur deconnecte ou cable casse. En attente d'un reset."
-
-# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
-#: Marlin_main.cpp:4512
-msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
-msgstr "Echec du nivellement. Capt. declenche trop trop haut. En attente d'un reset."
+msgstr "Echec bed leveling. Capt. non declenche. Debris sur buse ? En attente d'un reset."
 
 # MSG_BED
 #: messages.c:15
@@ -161,22 +151,22 @@ msgid "Bed"
 msgstr "Lit"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2002
 msgid "Belt status"
 msgstr "Statut courroie"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Coupure detectee. Recup. impression ?"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
-msgstr ""
+msgstr "Calib. mise a 0"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5671
 msgid "Calibrate XYZ"
 msgstr "Calibrer XYZ"
 
@@ -186,12 +176,12 @@ msgid "Calibrate Z"
 msgstr "Calibrer Z"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4570
 msgid "Calibrate"
 msgstr "Calibrer"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibration de XYZ. Tournez le bouton pour monter le chariot de l'axe Z jusqu'aux butees. Cliquez une fois fait."
 
@@ -201,37 +191,32 @@ msgid "Calibrating Z"
 msgstr "Calibration de Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibration de Z. Tournez le bouton pour monter le chariot de l'axe Z jusqu'aux butees. Cliquez une fois fait."
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:813
 msgid "Calibration done"
 msgstr "Calibration terminee"
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
-msgstr "Calibration"
+msgstr ""
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Cancel"
 msgstr "Annuler"
 
-# MSG_SD_INSERTED
-#: 
-msgid "Card inserted"
-msgstr "Carte  inseree"
-
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Carte retiree"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2676
 msgid "Color not correct"
 msgstr "Couleur incorrecte"
 
@@ -241,9 +226,9 @@ msgid "Cooldown"
 msgstr "Refroidissement"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4503
 msgid "Copy selected language?"
-msgstr "Copier la langue selectionne?"
+msgstr "Copier la langue selectionne ?"
 
 # MSG_CRASHDETECT_ON
 #: messages.c:27
@@ -253,12 +238,12 @@ msgstr "Detect. crash[on]"
 # MSG_CRASHDETECT_NA
 #: messages.c:25
 msgid "Crash det.  [N/A]"
-msgstr "Detect.crash[N/A]"
+msgstr "Detect. crash [N/A]"
 
 # MSG_CRASHDETECT_OFF
 #: messages.c:26
 msgid "Crash det.  [off]"
-msgstr "Detect.crash[off]"
+msgstr "Detect. crash[off]"
 
 # MSG_CRASH_DETECTED c=20 r=1
 #: messages.c:24
@@ -266,147 +251,97 @@ msgid "Crash detected."
 msgstr "Crash detecte."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:600
 msgid "Crash detected. Resume print?"
 msgstr "Crash detecte. Poursuivre l'impression ?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Crash"
-msgstr "Colision"
+msgstr ""
 
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5823
 msgid "Current"
 msgstr "Actuel"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2102
 msgid "Date:"
 msgstr "Date :"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5568
 msgid "Disable steppers"
 msgstr "Desactiver moteurs"
 
 # MSG_BABYSTEP_Z_NOT_SET c=20 r=12
 #: messages.c:14
 msgid "Distance between tip of the nozzle and the bed surface has not been set yet. Please follow the manual, chapter First steps, section First layer calibration."
-msgstr "La distance entre la pointe de la buse et la surface du lit n'a pas encore ete reglee. Suivez le manuel, chapitre Premiers pas, section Calibration de la premiere couche."
+msgstr "La distance entre la pointe de la buse et la surface du plateau n'a pas encore ete reglee. Suivez le manuel, chapitre Premiers pas, section Calibration de la premiere couche."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4984
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
-msgstr "Voulez-vous repeter la derniere etape pour reajuster la distance entre la buse et le lit chauffant ?"
+msgstr "Voulez-vous repeter la derniere etape pour reajuster la distance entre la buse et le plateau chauffant ?"
 
-# MSG_EXTRUDER_CORRECTION c=9
-#: ultralcd.cpp:4889
-msgid "E-correct"
-msgstr "Correct-E"
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5048
+msgid "E-correct:"
+msgstr "Correct-E:"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
-msgstr "Ejecter le fil"
-
-# MSG_EJECT_FILAMENT1 c=17 r=1
-#: ultralcd.cpp:5603
-msgid "Eject filament 1"
-msgstr "Ejecter fil. 1"
-
-# MSG_EJECT_FILAMENT2 c=17 r=1
-#: ultralcd.cpp:5604
-msgid "Eject filament 2"
-msgstr "Ejecter fil. 2"
-
-# MSG_EJECT_FILAMENT3 c=17 r=1
-#: ultralcd.cpp:5605
-msgid "Eject filament 3"
-msgstr "Ejecter fil. 3"
-
-# MSG_EJECT_FILAMENT4 c=17 r=1
-#: ultralcd.cpp:5606
-msgid "Eject filament 4"
-msgstr "Ejecter fil. 4"
-
-# MSG_EJECT_FILAMENT5 c=17 r=1
-#: ultralcd.cpp:5607
-msgid "Eject filament 5"
-msgstr "Ejecter fil. 5"
+msgstr "Ejecter le fil."
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Eject"
 msgstr "Ejecter"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1434
 msgid "Ejecting filament"
-msgstr "Filament en cours d'ejection"
+msgstr "Ejection filament"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Butee non atteinte"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Butee"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Butees"
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Erreur - la memoire statique a ete ecrasee"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4391
 msgid "ERROR: Filament sensor is not responding, please check connection."
-msgstr "ERREUR : Le capteur de filament ne repond pas, verifiez la connexion."
+msgstr "ERREUR : Le capteur de filament ne repond pas, verifiez le branchement."
 
 # MSG_ERROR
 #: messages.c:28
 msgid "ERROR:"
 msgstr "ERREUR :"
 
-# 
-#: Marlin_main.cpp:1006
-msgid "External SPI flash W25X20CL not responding."
-msgstr "La Flash SPI externe W25X20CL ne repond pas."
-
-# 
-#: ultralcd.cpp:5633
-msgid "Extruder 1"
-msgstr "Extrudeur 1"
-
-# 
-#: ultralcd.cpp:5634
-msgid "Extruder 2"
-msgstr "Extrudeur 2"
-
-# 
-#: ultralcd.cpp:5635
-msgid "Extruder 3"
-msgstr "Extrudeur 3"
-
-# 
-#: ultralcd.cpp:5636
-msgid "Extruder 4"
-msgstr "Extrudeur 4"
-
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Ventilo extrudeur:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2133
 msgid "Extruder info"
 msgstr "Infos extrudeur"
 
@@ -416,14 +351,14 @@ msgid "Extruder"
 msgstr "Extrudeur"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
-msgstr ""
+msgstr "Stat. echecs MMU"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5082
 msgid "F. autoload  [on]"
-msgstr "AutoCharg F  [on]"
+msgstr "ChargAuto f. [on]"
 
 # MSG_FSENS_AUTOLOAD_NA c=17 r=1
 #: messages.c:43
@@ -431,12 +366,12 @@ msgid "F. autoload [N/A]"
 msgstr "AutoCharg F [N/A]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5084
 msgid "F. autoload [off]"
 msgstr "AutoCharg F [off]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr "Statist. d'echec"
 
@@ -446,17 +381,17 @@ msgid "Fan speed"
 msgstr "Vitesse ventil"
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventilateur"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5577
 msgid "Fans check   [on]"
-msgstr "Verif venti  [on]"
+msgstr "Verif ventilo[on]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5579
 msgid "Fans check  [off]"
 msgstr "Verif venti [off]"
 
@@ -465,15 +400,10 @@ msgstr "Verif venti [off]"
 msgid "Fil. sensor  [on]"
 msgstr "Capteur Fil. [on]"
 
-# MSG_RESPONSE_POOR c=20 r=2
-#: Marlin_main.cpp:3146
-msgid "Fil. sensor response is poor, disable it?"
-msgstr "La reponse du capteur de fil. est pauvre, le desactiver ?"
-
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5062
 msgid "Fil. sensor [N/A]"
-msgstr "Capteur Fil.[N/A]"
+msgstr "Capteur Fil. [N/A]"
 
 # MSG_FSENSOR_OFF
 #: messages.c:44
@@ -481,9 +411,9 @@ msgid "Fil. sensor [off]"
 msgstr "Capteur Fil.[off]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Filam. runouts"
-msgstr "Manque de flm"
+msgstr "Fins de filament"
 
 # MSG_FILAMENT_CLEAN c=20 r=2
 #: messages.c:32
@@ -491,32 +421,27 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament extrude et avec bonne couleur ?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2672
 msgid "Filament not loaded"
 msgstr "Filament non charge"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Capteur de filament"
 
-# MSG_SELFTEST_FILAMENT_SENSOR c=18
-#: ultralcd.cpp:7477
-msgid "Filament sensor:"
-msgstr "Capteur filament :"
-
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2841
 msgid "Filament used"
 msgstr "Filament utilise"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2841
 msgid "Print time"
 msgstr "Temps d'impression"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Fichier incomplet. Continuer qd meme ?"
 
@@ -526,52 +451,52 @@ msgid "Finishing movements"
 msgstr "Mouvements de fin"
 
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Cal. 1ere couche"
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4896
 msgid "First, I will run the selftest to check most common assembly problems."
-msgstr "D'abord, je vais lancer l'autotest pour verifier les problemes d'assemblage les plus communs."
+msgstr "D'abord, je vais lancer le Selftest pour verifier les problemes d'assemblage les plus communs."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Corrigez le probleme et appuyez sur le bouton de l'unite MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Flux"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2095
 msgid "forum.prusa3d.com"
 msgstr ""
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Ventilo impr avant ?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3220
 msgid "Front side[um]"
 msgstr "Avant [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Ventilos avt/gauche"
 
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Chauffage/Thermistor"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8468
 msgid "Heating disabled by safety timer."
 msgstr "Chauffe desactivee par le compteur de securite."
 
@@ -586,67 +511,62 @@ msgid "Heating"
 msgstr "Chauffe"
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4875
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Bonjour, je suis votre imprimante Original Prusa i3. Voulez-vous que je vous guide a travers le processus d'installation ?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2096
 msgid "howto.prusa3d.com"
 msgstr ""
 
-# 
-#: ultralcd.cpp:6087
-msgid "Change extruder"
-msgstr "Changer extrudeur"
-
 # MSG_FILAMENTCHANGE
 #: messages.c:37
 msgid "Change filament"
 msgstr "Changer filament"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2587
 msgid "Change success!"
 msgstr "Changement reussi!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2664
 msgid "Changed correctly?"
 msgstr "Change correctement?"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Verification du lit"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Verifications butees"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Verif. tete impr."
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Verif. des capteurs"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Verification axe X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Verification axe Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Verification axe Z"
 
@@ -666,119 +586,89 @@ msgid "Filament"
 msgstr ""
 
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4905
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Je vais maintenant lancer la calibration xyz. Cela prendra 12 min environ."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4913
 msgid "I will run z calibration now."
 msgstr "Je vais maintenant lancer la calibration z."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4978
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
-msgstr "Je vais commencer a imprimer une ligne et vous baisserez au fur et a mesure la buse en tournant le bouton jusqu'a atteindre la hauteur optimale. Regardez les photos dans notre manuel au chapitre Calibration."
-
-# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
-#: mesh_bed_calibration.cpp:2481
-msgid "Improving bed calibration point"
-msgstr "Amelioration du point de calibration du lit"
+msgstr "Je vais commencer a imprimer une ligne et vous baisserez au fur et a mesure la buse en tournant le bouton jusqu'a atteindre la hauteur optimale. Regardez les photos dans notre manuel au chapitre Calibration"
 
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Ecran d'info"
 
-# MSG_FILAMENT_LOADING_T0 c=20 r=4
-#: messages.c:33
-msgid "Insert filament into extruder 1. Click when done."
-msgstr "Inserez le filament dans l'extrudeur 1. Cliquez une fois fait."
-
-# MSG_FILAMENT_LOADING_T1 c=20 r=4
-#: messages.c:34
-msgid "Insert filament into extruder 2. Click when done."
-msgstr "Inserez le filament dans l'extrudeur 2. Cliquez une fois fait."
-
-# MSG_FILAMENT_LOADING_T2 c=20 r=4
-#: messages.c:35
-msgid "Insert filament into extruder 3. Click when done."
-msgstr "Inserez le filament dans l'extrudeur 3. Cliquez une fois fait."
-
-# MSG_FILAMENT_LOADING_T3 c=20 r=4
-#: messages.c:36
-msgid "Insert filament into extruder 4. Click when done."
-msgstr "Inserez le filament dans l'extrudeur 4. Cliquez une fois fait."
-
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:4938
 msgid "Is filament 1 loaded?"
 msgstr "Le filament 1 est-il charge ?"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2572
 msgid "Insert filament"
 msgstr "Inserez le filament"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4941
 msgid "Is filament loaded?"
 msgstr "Le filament est-il charge ?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4972
 msgid "Is it PLA filament?"
 msgstr "Est-ce du filament PLA ?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4704
 msgid "Is PLA filament loaded?"
 msgstr "Le filament PLA est-il charge ?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
-msgstr "Feuille d'acier sur le lit chauffant ?"
-
-# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
-#: mesh_bed_calibration.cpp:2223
-msgid "Iteration "
-msgstr ""
+msgstr "Feuille d'acier sur plateau chauffant ?"
 
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1840
 msgid "Last print failures"
-msgstr "Echecs d'impr. dern."
+msgstr "Echecs derniere impr"
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1823
 msgid "Last print"
-msgstr "Derniere impress."
+msgstr "Derniere impression"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Ventilo tete gauche?"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2970
 msgid "Left"
 msgstr "Gauche"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3218
 msgid "Left side [um]"
 msgstr "Gauche [um]"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5594
 msgid "Lin. correction"
 msgstr "Correction lin."
 
 # MSG_BABYSTEP_Z
 #: messages.c:13
 msgid "Live adjust Z"
-msgstr "Ajuster Z en dir"
+msgstr "Ajuster Z en direct"
 
 # MSG_LOAD_FILAMENT c=17
 #: messages.c:51
@@ -786,7 +676,7 @@ msgid "Load filament"
 msgstr "Charger filament"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2612
 msgid "Loading color"
 msgstr "Chargement couleur"
 
@@ -796,239 +686,234 @@ msgid "Loading filament"
 msgstr "Chargement filament"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Poulie lache"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6719
 msgid "Load to nozzle"
-msgstr "Charger le fil"
+msgstr "Charger dans la buse"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Cal. 1ere couche"
 
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Principal"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Mesure de la hauteur de reference du point de calibration"
 
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5677
 msgid "Mesh Bed Leveling"
-msgstr "Nivelage du lit"
+msgstr ""
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Reprise de la position ..."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
-msgstr "MMU OK. Reprise de la temperature ..."
+msgstr "MMU OK. Remontee en temperature..."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3005
 msgid "Measured skew"
 msgstr "Deviation mesuree"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU fails"
-msgstr ""
+msgstr "Echec MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1613
 msgid "MMU load failed     "
-msgstr ""
+msgstr "Echec chargement MMU"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU load fails"
-msgstr ""
+msgstr "Echecs charg. MMU"
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Reprise ..."
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
-msgstr "Mode     [Normal]"
+msgstr ""
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Mode [silencieux]"
 
 # 
-#: mmu.cpp:635
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "Le MMU necessite l'attention de l'utilisateur."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "MMU power fails"
-msgstr ""
+msgstr "Echecs alim. MMU"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
-msgstr "Mode     [Furtif]"
+msgstr "Mode [Furtif]"
 
 # MSG_AUTO_MODE_ON
 #: messages.c:12
 msgid "Mode [auto power]"
-msgstr "Mode[puissan.aut]"
+msgstr "Mode [puiss.auto]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
-msgstr "Mode[haute puiss]"
+msgstr "Mode [haute puiss]"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2108
 msgid "MMU2 connected"
-msgstr "MMU2 connectée"
+msgstr "MMU2 connecte"
 
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Moteur"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5566
 msgid "Move axis"
 msgstr "Deplacer l'axe"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4294
 msgid "Move X"
 msgstr "Deplacer X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4295
 msgid "Move Y"
 msgstr "Deplacer Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4296
 msgid "Move Z"
 msgstr "Deplacer Z"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5291
 msgid "No move."
 msgstr "Pas de mouvement."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6686
 msgid "No SD card"
 msgstr "Pas de carte SD"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2976
 msgid "N/A"
 msgstr ""
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Non"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Non connecte"
 
 # 
 #: util.cpp:293
 msgid "New firmware version available:"
-msgstr "Nouvelle version de firmware disponible :"
-
-# 
-#: 
-msgid "No "
-msgstr "Non"
+msgstr "Nouvelle version de firmware disponible:"
 
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Ne tourne pas"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4977
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
-msgstr "Maintenant je vais calibrer la distance entre la pointe de la buse et le surface du lit chauffant."
+msgstr "Maintenant je vais calibrer la distance entre la pointe de la buse et la surface du plateau chauffant."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4921
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Maintenant je vais prechauffer la buse pour du PLA."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Buse"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1519
 msgid "Old settings found. Default PID, Esteps etc. will be set."
-msgstr "Anciens reglages trouves. Le PID, les Esteps etc. par defaut seront pris."
+msgstr "Anciens reglages trouves. Le PID, les Esteps etc. par defaut seront regles"
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4912
 msgid "Now remove the test print from steel sheet."
 msgstr "Retirez maintenant l'impression de test de la feuille d'acier."
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:1782
 msgid "Nozzle FAN"
-msgstr "Vent buse"
+msgstr "Ventilateur buse"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6649
 msgid "Pause print"
-msgstr "Pause de l'impres"
+msgstr "Pause de l'impr."
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1598
 msgid "PID cal.           "
 msgstr "Calib. PID"
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1604
 msgid "PID cal. finished"
 msgstr "Calib. PID terminee"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5683
 msgid "PID calibration"
 msgstr "Calibration PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:843
 msgid "PINDA Heating"
 msgstr "Chauffe de la PINDA"
 
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
-msgstr "Placez une feuille de papier sous la buse pendant la calibration des 4 premiers points. Si la buse accroche le papier, eteignez de suite l'imprimante."
+msgstr "Placez une feuille de papier sous la buse pendant la calibration des 4 premiers points. Si la buse accroche le papier, eteignez vite l'imprimante."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4986
 msgid "Please clean heatbed and then press the knob."
-msgstr "Nettoyez le lit chauffant et appuyez sur le bouton."
+msgstr "Nettoyez le plateau chauffant et appuyez sur le bouton."
 
 # MSG_CONFIRM_NOZZLE_CLEAN c=20 r=8
 #: messages.c:22
@@ -1036,92 +921,92 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Nettoyez la buse pour la calibration. Cliquez une fois fait."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Verifiez :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Merci de verifier notre manuel et de corriger le probleme. Poursuivez alors l'assistant en redemarrant l'imprimante."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4808
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
-msgstr "Inserez du filament PLA dans l'extrudeur, puis appuyez sur le bouton pour le charger."
+msgstr "Inserez du filament PLA dans l'extrudeur puis appuyez sur le bouton pour le charger."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4709
 msgid "Please load PLA filament first."
 msgstr "Chargez d'abord le filament PLA."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3063
 msgid "Please open idler and remove filament manually."
-msgstr "Ouvrez le support de poulie et retirez le filament manuellement."
+msgstr "Ouvrez l'idler et retirez le filament manuellement."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
-msgstr "Placez la feuille d'acier sur le lit chauffant."
+msgstr "Placez la feuille d'acier sur le plateau chauffant."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Appuyez sur le bouton pour decharger le filament"
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4803
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Veuillez inserer du filament PLA dans le premier tube du MMU, et pressez sur le bouton pour le charger."
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Retirez immediatement le filament"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1440
 msgid "Please remove filament and then press the knob."
 msgstr "Veuillez retirer le filament puis appuyez sur le bouton."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
-msgstr "Retirez la feuille d'acier du lit chauffant"
+msgstr "Retirez la feuille d'acier du plateau chauffant."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4354
 msgid "Please run XYZ calibration first."
 msgstr "Veuillez d'abord lancer la calibration XYZ."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1359
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Veuillez mettre a jour le firmware de votre MMU2. En attente d'un reset."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Merci de patienter"
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4911
 msgid "Please remove shipping helpers first."
 msgstr "Veuillez retirer d'abord les protections d'envoi."
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Prechauffez la buse!"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6636
 msgid "Preheat"
 msgstr "Prechauffage"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Prechauffage de la buse. Merci de patienter."
 
@@ -1131,32 +1016,32 @@ msgid "Please upgrade."
 msgstr "Mettez a jour le FW."
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10365
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Appuyez sur le bouton pour prechauffer la buse et continuer."
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Power failures"
-msgstr "Coupures"
+msgstr "Coupures de courant"
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Impression annulee"
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2276
 msgid "Preheating to load"
-msgstr ""
+msgstr "Chauffe pour charger"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2280
 msgid "Preheating to unload"
-msgstr ""
+msgstr "Chauffe pr decharger"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Ventilo impr. :"
 
@@ -1166,57 +1051,47 @@ msgid "Print from SD"
 msgstr "Impr depuis la SD"
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2206
 msgid "Press the knob"
-msgstr ""
+msgstr "App. sur sur bouton"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1061
 msgid "Print paused"
 msgstr "Impression en pause"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Appuyez sur le bouton pour poursuivre la mise en temperature de la buse."
 
 # MSG_FOLLOW_CALIBRATION_FLOW c=20 r=8
 #: messages.c:41
 msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
-msgstr "L'imprimante n'a pas encore ete calibree. Suivez le manuel, chapitre Premiers pas, section Processus de calibration"
+msgstr "L'imprimante n'a pas encore ete calibree. Suivez le manuel, chapitre Premiers pas, section Processus de calibration."
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1784
 msgid "Print FAN"
-msgstr "Vent extru"
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK2.5 ready."
-msgstr "Prusa i3 MK2.5 prete."
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK3 ready."
-msgstr "Prusa i3 MK3 prete."
+msgstr "Ventilo impression"
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2094
 msgid "prusa3d.com"
 msgstr ""
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3221
 msgid "Rear side [um]"
 msgstr "Arriere [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9765
 msgid "Recovering print    "
 msgstr "Recup. impression"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Retirez l'ancien filament puis appuyez sur le bouton pour charger le nouveau."
 
@@ -1225,63 +1100,58 @@ msgstr "Retirez l'ancien filament puis appuyez sur le bouton pour charger le nou
 msgid "Prusa i3 MK3S OK."
 msgstr ""
 
-# 
-#: 
-msgid "Prusa i3 MK2 ready."
-msgstr "Prusa i3 MK2 prete."
-
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5688
 msgid "Reset XYZ calibr."
 msgstr "Reinit. calibr. XYZ"
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3222
 msgid "Reset"
 msgstr "Reinitialiser"
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6656
 msgid "Resume print"
 msgstr "Reprendre impression"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Reprise de l'impr."
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3219
 msgid "Right side[um]"
 msgstr "Droite [um]"
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5606
 msgid "RPi port     [on]"
-msgstr "Port RPi     [on]"
+msgstr "Port RPi [on]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5604
 msgid "RPi port    [off]"
-msgstr "Port RPi    [off]"
+msgstr "Port RPi [off]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4726
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Lancer l'Assistant supprimera les resultats actuels de calibration et commencera du debut. Continuer ?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5236
 msgid "SD card  [normal]"
 msgstr "Carte SD [normal]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5234
 msgid "SD card [flshAir]"
-msgstr "Carte SD[flshAir]"
+msgstr "Carte SD [flashAir]"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2971
 msgid "Right"
 msgstr "Droite"
 
@@ -1291,217 +1161,207 @@ msgid "Searching bed calibration point"
 msgstr "Recherche du point de calibration du lit"
 
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5613
 msgid "Select language"
 msgstr "Choisir langue"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Auto-test OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Debut auto-test"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5664
 msgid "Selftest         "
 msgstr "Auto-test"
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Erreur auto-test !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Echec de l'auto-test"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1551
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
-msgstr "L'auto-test sera lance pour calibrer la remise a zero precise sans capteur."
+msgstr "Le Selftest sera lance pour calibrer la remise a zero precise sans capteur"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4959
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Selectionnez la temperature de prechauffage de la buse qui correspond a votre materiau."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Select PLA filament:"
 msgstr "Selectionnez le filament PLA :"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3230
 msgid "Set temperature:"
 msgstr "Regler temp. :"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Reglages"
 
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5685
 msgid "Show end stops"
 msgstr "Afficher butees"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:3941
 msgid "Sensor state"
-msgstr ""
-
-# 
-#: 
-msgid "Sensors info"
-msgstr ""
-
-# 
-#: 
-msgid "Show pinda state"
-msgstr "Etat de la PINDA"
+msgstr "Etat capteur"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Certains fichiers ne seront pas tries. Max 100 fichiers tries par dossier."
 
 # MSG_SORT_NONE c=17 r=1
-#: ultralcd.cpp:5043
-msgid "Sort:      [none]"
+#: ultralcd.cpp:5246
+msgid "Sort       [none]"
 msgstr "Tri :     [aucun]"
 
 # MSG_SORT_TIME c=17 r=1
-#: ultralcd.cpp:5041
-msgid "Sort:      [time]"
-msgstr "Tri :     [heure]"
+#: ultralcd.cpp:5244
+msgid "Sort       [time]"
+msgstr "Tri       [heure]"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3008
 msgid "Severe skew"
 msgstr "Deviation severe"
 
 # MSG_SORT_ALPHA c=17 r=1
-#: ultralcd.cpp:5042
-msgid "Sort:  [alphabet]"
-msgstr "Tri :  [alphabet]"
+#: ultralcd.cpp:5245
+msgid "Sort   [alphabet]"
+msgstr "Tri    [alphabet]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Tri des fichiers"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
-msgstr "Son        [fort]"
+msgstr "Son [fort]"
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3007
 msgid "Slight skew"
 msgstr "Deviation legere"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#: 
 msgid "Sound      [mute]"
-msgstr "Son        [muet]"
+msgstr "Son [muet]"
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4870
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Problemes rencontres, nivellement de l'axe Z applique..."
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
-msgstr "Son    [une fois]"
+msgstr "Son [une fois]"
 
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
-msgstr "Son  [silencieux]"
+msgstr "Son [silencieux]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Vitesse"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Tourne"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4367
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
-msgstr "Une temperature ambiante stable de 21-26C et une base stable sont requis."
+msgstr "Une temperature ambiante stable de 21-26C et un support stable sont requis."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistiques"
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Arreter impression"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ARRETE."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr ""
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Echange"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Calib. Temp."
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5600
 msgid "Temp. cal.   [on]"
 msgstr "Calib. Temp. [on]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5598
 msgid "Temp. cal.  [off]"
 msgstr "Calib. Temp.[off]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5694
 msgid "Temp. calibration"
 msgstr "Calibration temp."
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3867
 msgid "Temperature calibration failed"
-msgstr "Echec calibration en temperature"
+msgstr "Echec de la calibration en temperature"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
-msgstr "La calibration en temperature est terminee et active. La calibration en temperature peut etre desactivee dans le menu Reglages->Cal. Temp."
+msgstr "La calibration en temperature est terminee et activee. La calibration en temperature peut etre desactivee dans le menu Reglages-> Cal. Temp."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5564
 msgid "Temperature"
 msgstr ""
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2140
 msgid "Temperatures"
 msgstr ""
 
@@ -1511,127 +1371,122 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Il y a encore besoin d'effectuer la calibration Z. Veuillez suivre le manuel, chapitre Premiers pas, section Processus de calibration."
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2863
 msgid "Total filament"
 msgstr "Filament total"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2863
 msgid "Total print time"
-msgstr "Temps total"
+msgstr "Temps total impr."
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6633
 msgid "Tune"
 msgstr "Regler"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Unload"
 msgstr "Decharger"
 
 # 
-#: ultralcd.cpp:5617
-msgid "Unload all"
-msgstr "Decharger tout"
-
-# 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "Total failures"
-msgstr "Echecs au total"
+msgstr "Total des echecs"
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2213
 msgid "to load filament"
-msgstr ""
+msgstr "pour charger le fil."
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2217
 msgid "to unload filament"
-msgstr ""
+msgstr "pour decharger fil."
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Decharger fil."
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Dechargement fil."
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1824
 msgid "Total"
-msgstr "Total"
+msgstr ""
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5822
 msgid "Used during print"
 msgstr "Utilise pdt impr."
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2143
 msgid "Voltages"
 msgstr "Tensions"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2116
 msgid "unknown"
-msgstr ""
+msgstr "inconnu"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5262
 msgid "Wait for user..."
 msgstr "Attente utilisateur..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3374
 msgid "Waiting for nozzle and bed cooling"
-msgstr "Attente du refroidissement de la buse et du lit"
+msgstr "Attente du refroidissement des buse et plateau"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3338
 msgid "Waiting for PINDA probe cooling"
 msgstr "Attente du refroidissement de la sonde PINDA"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4782
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Utilisez decharger pour retirer le filament 1 s'il depasse du  tube arriere du MMU. Utilisez ejecter s'il est cache dans le tube."
 
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1511
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Attention : Types d'imprimante et de carte mere modifies"
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1503
 msgid "Warning: motherboard type changed."
 msgstr "Attention : Type de carte mere modifie."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1507
 msgid "Warning: printer type changed."
 msgstr "Attention : Type d'imprimante modifie"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3053
 msgid "Was filament unload successful?"
 msgstr "Dechargement du filament reussi ?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Erreur de cablage"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5661
 msgid "Wizard"
 msgstr "Assistant"
 
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2132
 msgid "XYZ cal. details"
 msgstr "Details calib. XYZ"
 
@@ -1641,107 +1496,312 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Echec calibration XYZ. Consultez le manuel."
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Oui"
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
-msgstr "Vous pouvez toujours poursuivre l'assistant dans Calibration-> Assistant."
+msgstr "Vous pouvez toujours relancer l'assistant dans Calibration-> Assistant."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3838
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Calibration XYZ OK. L'ecart sera corrige automatiquement."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Calibration XYZ OK. Les axes X/Y sont legerement non perpendiculaires. Bon boulot !"
 
 # 
-#: ultralcd.cpp:4885
-msgid "X-correct"
-msgstr "Correction-X"
+#: ultralcd.cpp:5044
+msgid "X-correct:"
+msgstr "Correct-X:"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3832
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Calibration XYZ OK. Les axes X/Y sont perpendiculaires. Felicitations !"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Calibration XYZ compromise. Les points de calibration avant ne sont pas atteignables."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3819
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
-msgstr "Calibration XYZ compromise. Le point de calibration avant droite n'est pas atteignable."
-
-# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
-#: ultralcd.cpp:3699
-msgid "XYZ calibration compromised. Left front calibration point not reachable."
-msgstr "Calibration XYZ compromise. Le point de calibration avant gauche n'est pas atteignable."
+msgstr "Calibration XYZ compromise. Le point de calibration avant droit n'est pas atteignable."
 
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6080
 msgid "Load all"
 msgstr "Tout charger"
 
-# MSG_LOAD_FILAMENT_1 c=17
-#: ultralcd.cpp:5576
-msgid "Load filament 1"
-msgstr "Charger fil. 1"
-
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3798
 msgid "XYZ calibration failed. Bed calibration point was not found."
-msgstr "Echec calibration XYZ. Le point de calibration du lit n'a pas ete trouve."
+msgstr "Echec calibration XYZ. Le point de calibration du plateau n'a pas ete trouve."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Echec calibration XYZ. Les points de calibration avant ne sont pas atteignables."
 
 # 
-#: ultralcd.cpp:3687
-msgid "XYZ calibration failed. Left front calibration point not reachable."
-msgstr "Echec calibration XYZ. Le point de calibration avant gauche n'est pas atteignable."
+#: ultralcd.cpp:3807
+msgid "XYZ calibration failed. Right front calibration point not reachable."
+msgstr "Echec calibration XYZ. Le point de calibration avant droit n'est pas atteignable."
 
-# MSG_LOAD_FILAMENT_2 c=17
-#: ultralcd.cpp:5577
-msgid "Load filament 2"
-msgstr "Charger fil. 2"
+# 
+#: ultralcd.cpp:2968
+msgid "Y distance from min"
+msgstr "Distance Y du min"
 
 # 
-#: ultralcd.cpp:3684
-msgid "XYZ calibration failed. Right front calibration point not reachable."
-msgstr "Echec calibration XYZ. Le point de calibration avant droite n'est pas atteignable."
+#: ultralcd.cpp:5045
+msgid "Y-correct:"
+msgstr "Correct-Y:"
 
-# MSG_LOAD_FILAMENT_3 c=17
-#: ultralcd.cpp:5578
-msgid "Load filament 3"
-msgstr "Charger fil. 3"
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr ""
 
 # 
-#: ultralcd.cpp:2859
-msgid "Y distance from min"
-msgstr "Distance Y du min"
+#: messages.c:57
+msgid "Back"
+msgstr ""
 
 # 
-#: ultralcd.cpp:4886
-msgid "Y-correct"
-msgstr "Correction-Y"
+#: ultralcd.cpp:5553
+msgid "Checks"
+msgstr ""
 
-# MSG_LOAD_FILAMENT_4 c=17
-#: ultralcd.cpp:5579
-msgid "Load filament 4"
-msgstr "Charger fil. 4"
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr ""
+
+# 
+#: ultralcd.cpp:3946
+msgid "FINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5459
+msgid "Firmware   [none]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5465
+msgid "Firmware [strict]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5462
+msgid "Firmware   [warn]"
+msgstr ""
+
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr ""
+
+# 
+#: ultralcd.cpp:3950
+msgid "IR:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5591
+msgid "Mesh bed leveling"
+msgstr ""
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5220
+msgid "MMU Mode [Normal]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5221
+msgid "MMU Mode[Stealth]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:4427
+msgid "Mode change in progress ..."
+msgstr ""
+
+# 
+#: ultralcd.cpp:5420
+msgid "Model      [none]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5426
+msgid "Model    [strict]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5423
+msgid "Model      [warn]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5381
+msgid "Nozzle d.  [0.25]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5384
+msgid "Nozzle d.  [0.40]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5387
+msgid "Nozzle d.  [0.60]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5335
+msgid "Nozzle     [none]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5341
+msgid "Nozzle   [strict]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5338
+msgid "Nozzle     [warn]"
+msgstr ""
+
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:3942
+msgid "PINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2286
+msgid "Preheating to cut"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2283
+msgid "Preheating to eject"
+msgstr ""
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:6597
+msgid "Rename"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6593
+msgid "Select"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2134
+msgid "Sensor info"
+msgstr ""
 
-# MSG_LOAD_FILAMENT_5 c=17
-#: ultralcd.cpp:5582
-msgid "Load filament 5"
-msgstr "Charger fil. 5"
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr ""
+
+# 
+#: 
+msgid "Sound     [assist]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5046
+msgid "Z-correct:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr ""
 

lang/po/Firmware_it.po

@@ -7,8 +7,8 @@ msgstr ""
 "Content-Transfer-Encoding: 8bit\n"
 "Language: it\n"
 "Project-Id-Version: Prusa-Firmware\n"
-"POT-Creation-Date: čt 7. úno 2019 14:48:23\n"
-"PO-Revision-Date: čt 7. úno 2019 14:48:23\n"
+"POT-Creation-Date: Wed Sep 4 16:14:05 CEST 2019\n"
+"PO-Revision-Date: Wed Sep 4 16:14:05 CEST 2019\n"
 "Language-Team: \n"
 "X-Generator: Poedit 2.0.7\n"
 "X-Poedit-SourceCharset: UTF-8\n"
@@ -21,74 +21,74 @@ msgid " of 4"
 msgstr " su 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr "su 9"
 
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3027
 msgid "[0;0] point offset"
 msgstr "[0;0] punto offset"
 
 # MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
-#: ultralcd.cpp:4219
-msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
-msgstr "\x1b[2JRilev. impatto\x1b[1;0Hattivabile solo\x1b[2;0Hin Modalita normale"
+#: 
+msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
+msgstr "Rilev. impatto\x0aattivabile solo\x0ain Modalita normale"
 
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-#: ultralcd.cpp:4231
-msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
-msgstr "\x1b[2JATTENZIONE:\x1b[1;0HRilev. impatto\x1b[2;0Hdisattivato in\x1b[3;0HModalita silenziosa"
+#: 
+msgid "WARNING:\x0aCrash detection disabled in Stealth mode"
+msgstr "ATTENZIONE:\x0aRilev. impatto\x0adisattivato in\x0aModalita silenziosa"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2290
 msgid ">Cancel"
-msgstr ""
+msgstr ">Annulla"
 
-# MSG_BABYSTEPPING_Z c=20
-#: ultralcd.cpp:3043
-msgid "Adjusting Z"
-msgstr "Compensazione Z"
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3147
+msgid "Adjusting Z:"
+msgstr "Compensaz. Z:"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Nessun errore"
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Tutto fatto. Buona stampa!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1974
 msgid "Ambient"
-msgstr ""
+msgstr "Ambiente"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2576
 msgid "and press the knob"
 msgstr "e cliccare manopola"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3445
 msgid "Are left and right Z~carriages all up?"
 msgstr "I carrelli Z sin/des sono altezza max?"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5114
 msgid "SpoolJoin    [on]"
-msgstr "SpoolJoin    [on]"
+msgstr ""
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5110
 msgid "SpoolJoin   [N/A]"
-msgstr "SpoolJoin   [N/A]"
+msgstr ""
 
-#  MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+# MSG_AUTO_DEPLETE_OFF c=17 r=1
+#: ultralcd.cpp:5118
 msgid "SpoolJoin   [off]"
-msgstr "SpoolJoin   [off]"
+msgstr ""
 
 # MSG_AUTO_HOME
 #: messages.c:11
@@ -96,32 +96,32 @@ msgid "Auto home"
 msgstr "Trova origine"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6736
 msgid "AutoLoad filament"
 msgstr "Autocaric. filam."
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4378
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Caricamento auto. filam. disp. solo con il sensore attivo..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2771
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Il caricamento automatico e attivo, premete la manopola e inserite il filamento..."
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Lunghezza dell'asse"
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Assi"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Letto/Riscald."
 
@@ -136,7 +136,7 @@ msgid "Bed Heating"
 msgstr "Riscald. letto"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5682
 msgid "Bed level correct"
 msgstr "Correz. liv.letto"
 
@@ -145,38 +145,28 @@ msgstr "Correz. liv.letto"
 msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
 msgstr "Livellamento letto fallito.NoRispSensore.Residui su ugello? In attesa di reset."
 
-# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
-#: Marlin_main.cpp:4508
-msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
-msgstr "Livellamento piano fallito. Sensore disconnesso o Cavo Danneggiato. In attesa di reset."
-
-# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
-#: Marlin_main.cpp:4512
-msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
-msgstr "Livellamento piano fallito. Risposta sensore troppo presto. In attesa di reset."
-
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Letto"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2002
 msgid "Belt status"
 msgstr "Stato delle cinghie"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "C'e stato un Blackout. Recuperare la stampa?"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
-msgstr ""
+msgstr "Calibrazione Home"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5671
 msgid "Calibrate XYZ"
 msgstr "Calibra XYZ"
 
@@ -186,12 +176,12 @@ msgid "Calibrate Z"
 msgstr "Calibra Z"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4570
 msgid "Calibrate"
 msgstr "Calibra"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrazione XYZ. Ruotare la manopola per alzare il carrello Z fino all'altezza massima. Click per terminare."
 
@@ -201,37 +191,32 @@ msgid "Calibrating Z"
 msgstr "Calibrando Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrazione Z. Ruotare la manopola per alzare il carrello Z fino all'altezza massima. Click per terminare."
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:813
 msgid "Calibration done"
 msgstr "Calibrazione completa"
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Calibrazione"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Cancel"
 msgstr "Annulla"
 
-# MSG_SD_INSERTED
-#: 
-msgid "Card inserted"
-msgstr "SD inserita"
-
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "SD rimossa"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2676
 msgid "Color not correct"
 msgstr "Colore non puro"
 
@@ -241,7 +226,7 @@ msgid "Cooldown"
 msgstr "Raffredda"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4503
 msgid "Copy selected language?"
 msgstr "Copiare la lingua selezionata?"
 
@@ -266,27 +251,27 @@ msgid "Crash detected."
 msgstr "Rilevato impatto."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:600
 msgid "Crash detected. Resume print?"
 msgstr "Scontro rilevato. Riprendere la stampa?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Crash"
-msgstr ""
+msgstr "Impatto"
 
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5823
 msgid "Current"
 msgstr "Attuale"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2102
 msgid "Date:"
 msgstr "Data:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5568
 msgid "Disable steppers"
 msgstr "Disabilita motori"
 
@@ -296,77 +281,52 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Distanza tra la punta dell'ugello e la superficie del letto non ancora imposta. Si prega di seguire il manuale, capitolo Primi Passi, sezione Calibrazione primo layer."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4984
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Desideri ripetere l'ultimo passaggio per migliorare la distanza fra ugello e piatto?"
 
-# MSG_EXTRUDER_CORRECTION c=9
-#: ultralcd.cpp:4889
-msgid "E-correct"
-msgstr "Correzione-E"
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5048
+msgid "E-correct:"
+msgstr "Correzione-E:"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Espelli filamento "
 
-# MSG_EJECT_FILAMENT1 c=17 r=1
-#: ultralcd.cpp:5603
-msgid "Eject filament 1"
-msgstr "Espelli filamento 1"
-
-# MSG_EJECT_FILAMENT2 c=17 r=1
-#: ultralcd.cpp:5604
-msgid "Eject filament 2"
-msgstr "Espellere filamento 2"
-
-# MSG_EJECT_FILAMENT3 c=17 r=1
-#: ultralcd.cpp:5605
-msgid "Eject filament 3"
-msgstr "Espelli filamento 3"
-
-# MSG_EJECT_FILAMENT4 c=17 r=1
-#: ultralcd.cpp:5606
-msgid "Eject filament 4"
-msgstr "Espellere filamento 4"
-
-# MSG_EJECT_FILAMENT5 c=17 r=1
-#: ultralcd.cpp:5607
-msgid "Eject filament 5"
-msgstr "Espelli filamento 5"
-
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Eject"
 msgstr "Espellere"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1434
 msgid "Ejecting filament"
 msgstr "Espellendo filamento "
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Finecorsa fuori portata"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Finecorsa"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Finecorsa"
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Errore - la memoria statica e stata sovrascritta"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4391
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "ERRORE: il sensore filam. non risponde,Controllare conness."
 
@@ -375,38 +335,13 @@ msgstr "ERRORE: il sensore filam. non risponde,Controllare conness."
 msgid "ERROR:"
 msgstr "ERRORE:"
 
-# 
-#: Marlin_main.cpp:1006
-msgid "External SPI flash W25X20CL not responding."
-msgstr "Flash SPI W25X20CL esterno non risponde."
-
-# 
-#: ultralcd.cpp:5633
-msgid "Extruder 1"
-msgstr "Estrusore 1"
-
-# 
-#: ultralcd.cpp:5634
-msgid "Extruder 2"
-msgstr "Estrusore 2"
-
-# 
-#: ultralcd.cpp:5635
-msgid "Extruder 3"
-msgstr "Estrusore 3"
-
-# 
-#: ultralcd.cpp:5636
-msgid "Extruder 4"
-msgstr "Estrusore 4"
-
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Ventola estrusore:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2133
 msgid "Extruder info"
 msgstr "Info estrusore"
 
@@ -416,12 +351,12 @@ msgid "Extruder"
 msgstr "Estrusore"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
-msgstr ""
+msgstr "Statistiche fallimenti MMU"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5082
 msgid "F. autoload  [on]"
 msgstr "Autocar.filam[on]"
 
@@ -431,14 +366,14 @@ msgid "F. autoload [N/A]"
 msgstr "Autocar.fil.[N/A]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5084
 msgid "F. autoload [off]"
 msgstr "Autocar.fil.[off]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
-msgstr ""
+msgstr "Statistiche fallimenti"
 
 # MSG_FAN_SPEED c=14
 #: messages.c:31
@@ -446,17 +381,17 @@ msgid "Fan speed"
 msgstr "Velocita ventola"
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventola"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5577
 msgid "Fans check   [on]"
 msgstr "Controllo ventole [on]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5579
 msgid "Fans check  [off]"
 msgstr "Control.vent[off]"
 
@@ -465,13 +400,8 @@ msgstr "Control.vent[off]"
 msgid "Fil. sensor  [on]"
 msgstr "Sensor filam.[On]"
 
-# MSG_RESPONSE_POOR c=20 r=2
-#: Marlin_main.cpp:3146
-msgid "Fil. sensor response is poor, disable it?"
-msgstr "Risposta Sens. Fil. debole, disattivare? "
-
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5062
 msgid "Fil. sensor [N/A]"
 msgstr "Sensor filam[N/A]"
 
@@ -481,9 +411,9 @@ msgid "Fil. sensor [off]"
 msgstr "Sensor filam[off]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Filam. runouts"
-msgstr ""
+msgstr "Filam. esauriti"
 
 # MSG_FILAMENT_CLEAN c=20 r=2
 #: messages.c:32
@@ -491,32 +421,27 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filamento estruso & con il giusto colore?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2672
 msgid "Filament not loaded"
 msgstr "Fil. non caricato"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Sensore filam."
 
-# MSG_SELFTEST_FILAMENT_SENSOR c=18
-#: ultralcd.cpp:7477
-msgid "Filament sensor:"
-msgstr "Sensore filam.:"
-
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2841
 msgid "Filament used"
 msgstr "Filamento utilizzato"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2841
 msgid "Print time"
 msgstr "Tempo di stampa"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "File incompleto. Continuare comunque?"
 
@@ -526,52 +451,52 @@ msgid "Finishing movements"
 msgstr "Finalizzando gli spostamenti"
 
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Calibrazione primo layer."
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4896
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Per primo avviero l'autotest per controllare gli errori di assemblaggio piu comuni."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Risolvi il problema e quindi premi il bottone sull'unita MMU. "
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Flusso"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2095
 msgid "forum.prusa3d.com"
 msgstr ""
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Ventola frontale?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3220
 msgid "Front side[um]"
 msgstr "Fronte [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Ventola frontale/sinistra"
 
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Riscald./Termist."
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8468
 msgid "Heating disabled by safety timer."
 msgstr "Riscaldamento fermato dal timer di sicurezza."
 
@@ -586,67 +511,62 @@ msgid "Heating"
 msgstr "Riscaldamento..."
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4875
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Ciao, sono la tua stampante Original Prusa i3. Gradiresti un aiuto nel processo di configurazione?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2096
 msgid "howto.prusa3d.com"
 msgstr ""
 
-# 
-#: ultralcd.cpp:6087
-msgid "Change extruder"
-msgstr "Cambio estrusore"
-
 # MSG_FILAMENTCHANGE
 #: messages.c:37
 msgid "Change filament"
 msgstr "Cambia filamento"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2587
 msgid "Change success!"
 msgstr "Cambio riuscito!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2664
 msgid "Changed correctly?"
 msgstr "Cambiato correttamente?"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Verifica piano"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Verifica finecorsa"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Verifica ugello"
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Controllo sensori"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Verifica asse X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Verifica asse Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Verifica asse Z"
 
@@ -666,112 +586,82 @@ msgid "Filament"
 msgstr "Filamento"
 
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4905
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Adesso avviero una Calibrazione XYZ. Puo durare circa 12 min."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4913
 msgid "I will run z calibration now."
 msgstr "Adesso avviero la Calibrazione Z."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4978
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Adesso iniziero a stampare una linea e tu dovrai abbassare l'ugello poco per volta ruotando la manopola sino a raggiungere una altezza ottimale. Per favore dai uno sguardo all'immagine del nostro manuale, cap.Calibrazione."
 
-# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
-#: mesh_bed_calibration.cpp:2481
-msgid "Improving bed calibration point"
-msgstr "Perfezion. punto di calibraz. letto"
-
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Schermata info"
 
-# MSG_FILAMENT_LOADING_T0 c=20 r=4
-#: messages.c:33
-msgid "Insert filament into extruder 1. Click when done."
-msgstr "Inserire filamento nell'estrusore 1. Click per continuare"
-
-# MSG_FILAMENT_LOADING_T1 c=20 r=4
-#: messages.c:34
-msgid "Insert filament into extruder 2. Click when done."
-msgstr "Inserire filamento nell'estrusore 2. Click per continuare"
-
-# MSG_FILAMENT_LOADING_T2 c=20 r=4
-#: messages.c:35
-msgid "Insert filament into extruder 3. Click when done."
-msgstr "Inserire filamento nell'estrusore 3. Click per continuare"
-
-# MSG_FILAMENT_LOADING_T3 c=20 r=4
-#: messages.c:36
-msgid "Insert filament into extruder 4. Click when done."
-msgstr "Inserire filamento nell'estrusore 4. Click per continuare"
-
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:4938
 msgid "Is filament 1 loaded?"
 msgstr "Il filamento 1 e caricato?"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2572
 msgid "Insert filament"
 msgstr "Inserire filamento"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4941
 msgid "Is filament loaded?"
 msgstr "Il filamento e stato caricato?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4972
 msgid "Is it PLA filament?"
 msgstr "E' un filamento di PLA?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4704
 msgid "Is PLA filament loaded?"
 msgstr "E' stato caricato il filamento di PLA?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "La piastra d'acciaio e sul piano riscaldato?"
 
-# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
-#: mesh_bed_calibration.cpp:2223
-msgid "Iteration "
-msgstr "Iterazione"
-
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1840
 msgid "Last print failures"
-msgstr ""
+msgstr "Fallimenti ultima stampa"
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1823
 msgid "Last print"
-msgstr ""
+msgstr "Ultima stampa"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Vent SX hotend?"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2970
 msgid "Left"
 msgstr "Sinistra"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3218
 msgid "Left side [um]"
 msgstr "Lato sinistro [um]"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5594
 msgid "Lin. correction"
 msgstr "Correzione lin."
 
@@ -786,7 +676,7 @@ msgid "Load filament"
 msgstr "Carica filamento"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2612
 msgid "Loading color"
 msgstr "Caricando colore"
 
@@ -796,92 +686,92 @@ msgid "Loading filament"
 msgstr "Caricando filamento"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Puleggia lenta"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6719
 msgid "Load to nozzle"
 msgstr "Carica ugello"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Calibrazione primo layer."
 
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Menu principale"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Misura altezza di rif. del punto di calib."
 
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5677
 msgid "Mesh Bed Leveling"
 msgstr "Mesh livel. letto"
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. riprendendo la posizione... "
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Ripristino temperatura... "
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3005
 msgid "Measured skew"
 msgstr "Disassamento misurato"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU fails"
-msgstr ""
+msgstr "Fallimenti MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1613
 msgid "MMU load failed     "
-msgstr ""
+msgstr "Caricamento MMU fallito"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU load fails"
-msgstr ""
+msgstr "Caricamenti MMU falliti"
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Riprendendo... "
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Modo    [normale]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Modo [silenzioso]"
 
 # 
-#: mmu.cpp:635
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "Il MMU richiede attenzione dall'utente."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "MMU power fails"
-msgstr ""
+msgstr "Mancanza corrente MMU"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Modo [Silenziosa]"
 
@@ -891,62 +781,62 @@ msgid "Mode [auto power]"
 msgstr "Modo       [auto]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Mode      [forte]"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2108
 msgid "MMU2 connected"
-msgstr ""
+msgstr "MMU2 connessa"
 
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Motore"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5566
 msgid "Move axis"
 msgstr "Muovi asse"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4294
 msgid "Move X"
 msgstr "Muovi X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4295
 msgid "Move Y"
 msgstr "Muovi Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4296
 msgid "Move Z"
 msgstr "Muovi Z"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5291
 msgid "No move."
 msgstr "Nessun movimento."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6686
 msgid "No SD card"
 msgstr "Nessuna SD"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2976
 msgid "N/A"
 msgstr ""
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr ""
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Non connesso"
 
@@ -955,78 +845,73 @@ msgstr "Non connesso"
 msgid "New firmware version available:"
 msgstr "Nuova versione firmware disponibile:"
 
-# 
-#: 
-msgid "No "
-msgstr "No"
-
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Non gira"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4977
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Adesso calibro la distanza fra ugello e superfice del piatto."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4921
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Adesso preriscaldero l'ugello per PLA."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Ugello"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1519
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Sono state trovate impostazioni vecchie. I valori di default di PID, Esteps etc. saranno impostati"
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4912
 msgid "Now remove the test print from steel sheet."
 msgstr "Ora rimuovete la stampa di prova dalla piastra in acciaio."
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:1782
 msgid "Nozzle FAN"
-msgstr ""
+msgstr "Ventola estrusore"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6649
 msgid "Pause print"
 msgstr "Metti in pausa"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1598
 msgid "PID cal.           "
 msgstr "Calibrazione PID"
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1604
 msgid "PID cal. finished"
 msgstr "Calib. PID completa"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5683
 msgid "PID calibration"
 msgstr "Calibrazione PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:843
 msgid "PINDA Heating"
 msgstr "Riscaldamento PINDA"
 
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Posizionare un foglio sotto l'ugello durante la calibrazione dei primi 4 punti. In caso l'ugello muova il foglio spegnere subito la stampante."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4986
 msgid "Please clean heatbed and then press the knob."
 msgstr "Per favore pulisci il piatto, poi premi la manopola."
 
@@ -1036,92 +921,92 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Pulire l'ugello per la calibrazione, poi fare click."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Verifica:"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Per favore consulta il nostro manuale per risolvere il problema. Poi riprendi il Wizard dopo aver riavviato la stampante."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4808
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Per favore inserisci il filamento di PLA nell'estrusore, poi premi la manopola per caricare."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4709
 msgid "Please load PLA filament first."
 msgstr "Per favore prima carica il filamento di PLA."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3063
 msgid "Please open idler and remove filament manually."
 msgstr "Aprire la guida filam. e rimuovere il filam. a mano"
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Per favore posizionate la piastra d'acciaio sul piano riscaldato."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Premete la manopola per scaricare il filamento "
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4803
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Per favore inserite del filamento PLA nel primo tubo del MMU, poi premete la manopola per caricarlo."
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Estrarre il filamento immediatamente"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1440
 msgid "Please remove filament and then press the knob."
 msgstr "Rimuovi il filamento e quindi premi la manopola. "
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Rimuovete la piastra di acciaio dal piano riscaldato"
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4354
 msgid "Please run XYZ calibration first."
 msgstr "Esegui la calibrazione XYZ prima. "
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1359
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Aggiorna il firmware sul tuo MMU2. In attesa di reset. "
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Attendere"
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4911
 msgid "Please remove shipping helpers first."
 msgstr "Per favore rimuovete i materiali da spedizione"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Prerisc. ugello!"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6636
 msgid "Preheat"
 msgstr "Preriscalda"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Preriscaldando l'ugello. Attendere prego."
 
@@ -1131,32 +1016,32 @@ msgid "Please upgrade."
 msgstr "Prego aggiornare."
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10365
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Premete la manopola per preriscaldare l'ugello e continuare."
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Power failures"
-msgstr ""
+msgstr "Mancanza corrente"
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Stampa interrotta"
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2276
 msgid "Preheating to load"
-msgstr ""
+msgstr "Preriscaldamento per caricare"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2280
 msgid "Preheating to unload"
-msgstr ""
+msgstr "Preriscaldamento per scaricare"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Ventola di stampa:"
 
@@ -1166,17 +1051,17 @@ msgid "Print from SD"
 msgstr "Stampa da SD"
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2206
 msgid "Press the knob"
-msgstr ""
+msgstr "Premere la manopola"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1061
 msgid "Print paused"
 msgstr "Stampa in pausa"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Premete la manopola per recuperare la temperatura dell'ugello."
 
@@ -1186,37 +1071,27 @@ msgid "Printer has not been calibrated yet. Please follow the manual, chapter Fi
 msgstr "Stampante non ancora calibrata. Si prega di seguire il manuale, capitolo Primi Passi, sezione Sequenza di Calibrazione."
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1784
 msgid "Print FAN"
-msgstr ""
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK2.5 ready."
-msgstr ""
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK3 ready."
-msgstr "Prusa i3 MK3 pronta."
+msgstr "Ventola di stampa"
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2094
 msgid "prusa3d.com"
 msgstr ""
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3221
 msgid "Rear side [um]"
 msgstr "Retro [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9765
 msgid "Recovering print    "
 msgstr "Recupero stampa"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Rimuovi il filamento precedente e premi la manopola per caricare il nuovo filamento. "
 
@@ -1225,63 +1100,58 @@ msgstr "Rimuovi il filamento precedente e premi la manopola per caricare il nuov
 msgid "Prusa i3 MK3S OK."
 msgstr ""
 
-# 
-#: 
-msgid "Prusa i3 MK2 ready."
-msgstr "Prusa i3 MK2 pronta."
-
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5688
 msgid "Reset XYZ calibr."
 msgstr "Reset calibrazione XYZ."
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3222
 msgid "Reset"
 msgstr ""
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6656
 msgid "Resume print"
 msgstr "Riprendi stampa"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Riprendi stampa"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3219
 msgid "Right side[um]"
 msgstr "Destra [um]"
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5606
 msgid "RPi port     [on]"
 msgstr "Porta RPi    [on]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5604
 msgid "RPi port    [off]"
 msgstr "Porta RPi   [off]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4726
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Se avvi il Wizard perderai la calibrazione preesistente e dovrai ricominciare dall'inizio. Continuare?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5236
 msgid "SD card  [normal]"
 msgstr "Mem. SD [normale]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5234
 msgid "SD card [flshAir]"
 msgstr "Mem. SD [flshAir]"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2971
 msgid "Right"
 msgstr "Destra"
 
@@ -1291,217 +1161,207 @@ msgid "Searching bed calibration point"
 msgstr "Ricerca dei punti di calibrazione del piano"
 
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5613
 msgid "Select language"
 msgstr "Seleziona lingua"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Autotest OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Avvia autotest"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5664
 msgid "Selftest         "
 msgstr "Autotest"
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Errore Autotest !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Autotest fallito"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1551
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Verra effettuato un self test per calibrare l'homing senza sensori"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4959
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Selezionate la temperatura per il preriscaldamento dell'ugello adatta al vostro materiale."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Select PLA filament:"
 msgstr "Selezionate filamento PLA:"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3230
 msgid "Set temperature:"
 msgstr "Imposta temperatura:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Impostazioni"
 
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5685
 msgid "Show end stops"
 msgstr "Stato finecorsa"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:3941
 msgid "Sensor state"
-msgstr ""
-
-# 
-#: 
-msgid "Sensors info"
-msgstr ""
-
-# 
-#: 
-msgid "Show pinda state"
-msgstr "Mostra stato pinda"
+msgstr "Stato sensore"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Alcuni file non saranno ordinati. Il numero massimo di file in una cartella e 100 perche siano ordinati."
 
 # MSG_SORT_NONE c=17 r=1
-#: ultralcd.cpp:5043
-msgid "Sort:      [none]"
-msgstr "Ordina:    [none]"
+#: ultralcd.cpp:5246
+msgid "Sort       [none]"
+msgstr "Ordina     [none]"
 
 # MSG_SORT_TIME c=17 r=1
-#: ultralcd.cpp:5041
-msgid "Sort:      [time]"
-msgstr "Ordina:    [time]"
+#: ultralcd.cpp:5244
+msgid "Sort       [time]"
+msgstr "Ordina     [time]"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3008
 msgid "Severe skew"
 msgstr "Disassamento grave"
 
 # MSG_SORT_ALPHA c=17 r=1
-#: ultralcd.cpp:5042
-msgid "Sort:  [alphabet]"
-msgstr "Ordine: [alfabet]"
+#: ultralcd.cpp:5245
+msgid "Sort   [alphabet]"
+msgstr "Ordine  [alfabet]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Ordinando i file"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Suono     [forte]"
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3007
 msgid "Slight skew"
 msgstr "Disassamento lieve"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#: 
 msgid "Sound      [mute]"
 msgstr "Suono      [mute]"
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4870
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Sono stati rilevati problemi, avviato livellamento Z ..."
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Suono   [singolo]"
 
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Suono[silenzioso]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Velocita"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Gira"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4367
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Sono necessari una temperatura ambiente di 21-26C e una superficie rigida "
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistiche"
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Arresta stampa"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ARRESTATO."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Supporto"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Scambiato"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Calib. temp. "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5600
 msgid "Temp. cal.   [on]"
 msgstr "Calib. temp. [ON]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5598
 msgid "Temp. cal.  [off]"
 msgstr "Calib. temp.[OFF]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5694
 msgid "Temp. calibration"
 msgstr "Calib. Temp."
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3867
 msgid "Temperature calibration failed"
 msgstr "Calibrazione temperatura fallita"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Calibrazione temperatura completata e attiva. Puo essere disattivata dal menu Impostazioni ->Cal. Temp."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5564
 msgid "Temperature"
 msgstr ""
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2140
 msgid "Temperatures"
 msgstr "Temperature"
 
@@ -1511,127 +1371,122 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "E ancora necessario effettuare la calibrazione Z. Segui il manuale, capitolo Primi Passi, sezione Sequenza di Calibrazione. "
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2863
 msgid "Total filament"
 msgstr "Filamento totale"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2863
 msgid "Total print time"
 msgstr "Tempo di stampa totale"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6633
 msgid "Tune"
 msgstr "Regola"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Unload"
 msgstr "Scarica"
 
 # 
-#: ultralcd.cpp:5617
-msgid "Unload all"
-msgstr "Rilasciare tutti"
-
-# 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "Total failures"
-msgstr ""
+msgstr "Totale fallimenti"
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2213
 msgid "to load filament"
-msgstr ""
+msgstr "per caricare il filamento"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2217
 msgid "to unload filament"
-msgstr ""
+msgstr "per scaricare il filamento"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Scarica filam."
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Scaricando filamento"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1824
 msgid "Total"
-msgstr ""
+msgstr "Totale"
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5822
 msgid "Used during print"
 msgstr "Usati nella stampa"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2143
 msgid "Voltages"
 msgstr "Voltaggi"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2116
 msgid "unknown"
-msgstr ""
+msgstr "sconosciuto"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5262
 msgid "Wait for user..."
 msgstr "Attendendo utente..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3374
 msgid "Waiting for nozzle and bed cooling"
 msgstr "In attesa del raffreddamento dell'ugello e del piano"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3338
 msgid "Waiting for PINDA probe cooling"
 msgstr "In attesa del raffreddamento della sonda PINDA"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4782
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Usate lo scaricamento per rimuovere il filamento 1 se protrude dal retro del tubo posteriore del MMu. Utilizzate l'espulsione se e nascosto nel tubo."
 
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1511
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Attenzione: tipo di stampante e di scheda madre cambiati."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1503
 msgid "Warning: motherboard type changed."
 msgstr "Avviso: tipo di scheda madre cambiato"
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1507
 msgid "Warning: printer type changed."
 msgstr "Avviso: tipo di stampante cambiato."
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3053
 msgid "Was filament unload successful?"
 msgstr "Filamento scaricato con successo?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Errore cablaggio"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5661
 msgid "Wizard"
 msgstr ""
 
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2132
 msgid "XYZ cal. details"
 msgstr "XYZ Cal. dettagli"
 
@@ -1641,107 +1496,312 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Calibrazione XYZ fallita. Si prega di consultare il manuale."
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Si"
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "E possibile riprendere il Wizard in qualsiasi momento attraverso Calibrazione -> Wizard."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3838
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Calibrazione XYZ corretta. La distorsione verra compensata automaticamente."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Calibrazion XYZ corretta. Assi X/Y leggermente storti. Ben fatto!"
 
 # 
-#: ultralcd.cpp:4885
-msgid "X-correct"
-msgstr "Correzione-X"
+#: ultralcd.cpp:5044
+msgid "X-correct:"
+msgstr "Correzione-X:"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3832
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Calibrazione XYZ OK. Gli assi X/Y sono perpendicolari. Complimenti!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Calibrazione XYZ compromessa. Punti anteriori non raggiungibili."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3819
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Calibrazione XYZ compromessa. Punto anteriore destro non raggiungibile."
 
-# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
-#: ultralcd.cpp:3699
-msgid "XYZ calibration compromised. Left front calibration point not reachable."
-msgstr "Calibrazione XYZ compromessa. Punto anteriore sinistro non raggiungibile."
-
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6080
 msgid "Load all"
 msgstr "Caricare tutti"
 
-# MSG_LOAD_FILAMENT_1 c=17
-#: ultralcd.cpp:5576
-msgid "Load filament 1"
-msgstr "Caricare fil. 1"
-
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3798
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Calibrazione XYZ fallita. Il punto di calibrazione sul letto non e' stato trovato."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Calibrazione XYZ fallita. Punti anteriori non raggiungibili."
 
 # 
-#: ultralcd.cpp:3687
-msgid "XYZ calibration failed. Left front calibration point not reachable."
-msgstr "Calibrazione XYZ fallita. Punto anteriore sinistro non raggiungibile."
-
-# MSG_LOAD_FILAMENT_2 c=17
-#: ultralcd.cpp:5577
-msgid "Load filament 2"
-msgstr "Caricare fil. 2"
-
-# 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3807
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Calibrazione XYZ fallita. Punto anteriore destro non raggiungibile."
 
-# MSG_LOAD_FILAMENT_3 c=17
-#: ultralcd.cpp:5578
-msgid "Load filament 3"
-msgstr "Carica fil. 3"
-
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2968
 msgid "Y distance from min"
 msgstr "Distanza Y dal min"
 
 # 
-#: ultralcd.cpp:4886
-msgid "Y-correct"
-msgstr "Correzione-Y"
+#: ultralcd.cpp:5045
+msgid "Y-correct:"
+msgstr "Correzione-Y:"
 
-# MSG_LOAD_FILAMENT_4 c=17
-#: ultralcd.cpp:5579
-msgid "Load filament 4"
-msgstr "Caricare fil. 4"
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr ""
+
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Indietro"
+
+# 
+#: ultralcd.cpp:5553
+msgid "Checks"
+msgstr "Controlli"
+
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falso innesco"
+
+# 
+#: ultralcd.cpp:3946
+msgid "FINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5459
+msgid "Firmware   [none]"
+msgstr "Firmware[nessuno]"
+
+# 
+#: ultralcd.cpp:5465
+msgid "Firmware [strict]"
+msgstr "Firmware [esatto]"
+
+# 
+#: ultralcd.cpp:5462
+msgid "Firmware   [warn]"
+msgstr "Firmware [avviso]"
+
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "Installazione HW"
+
+# 
+#: ultralcd.cpp:3950
+msgid "IR:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Comp. Magneti[N/A]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Comp. Magneti[off]"
+
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Comp. Magneti [on]"
+
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Griglia      [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Griglia      [7x7]"
+
+# 
+#: ultralcd.cpp:5591
+msgid "Mesh bed leveling"
+msgstr "Mesh livel. letto"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5220
+msgid "MMU Mode [Normal]"
+msgstr "Modalita MMU [Normale]"
+
+# 
+#: ultralcd.cpp:5221
+msgid "MMU Mode[Stealth]"
+msgstr "Modalita MMU [Silenziosa]"
+
+# 
+#: ultralcd.cpp:4427
+msgid "Mode change in progress ..."
+msgstr "Cambio modalita in corso ..."
+
+# 
+#: ultralcd.cpp:5420
+msgid "Model      [none]"
+msgstr "Modello [nessuno]"
+
+# 
+#: ultralcd.cpp:5426
+msgid "Model    [strict]"
+msgstr "Modello  [esatto]"
+
+# 
+#: ultralcd.cpp:5423
+msgid "Model      [warn]"
+msgstr "Modello  [avviso]"
+
+# 
+#: ultralcd.cpp:5381
+msgid "Nozzle d.  [0.25]"
+msgstr "Diam. Ugell[0.25]"
+
+# 
+#: ultralcd.cpp:5384
+msgid "Nozzle d.  [0.40]"
+msgstr "Diam. Ugell[0.40]"
+
+# 
+#: ultralcd.cpp:5387
+msgid "Nozzle d.  [0.60]"
+msgstr "Diam. Ugell[0.60]"
+
+# 
+#: ultralcd.cpp:5335
+msgid "Nozzle     [none]"
+msgstr "Ugello  [nessuno]"
+
+# 
+#: ultralcd.cpp:5341
+msgid "Nozzle   [strict]"
+msgstr "Ugello   [esatto]"
+
+# 
+#: ultralcd.cpp:5338
+msgid "Nozzle     [warn]"
+msgstr "Ugello   [avviso]"
+
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr ""
 
-# MSG_LOAD_FILAMENT_5 c=17
-#: ultralcd.cpp:5582
-msgid "Load filament 5"
-msgstr "Caricare fil. 5"
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:3942
+msgid "PINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2286
+msgid "Preheating to cut"
+msgstr "Preriscaldamento per taglio"
+
+# 
+#: ultralcd.cpp:2283
+msgid "Preheating to eject"
+msgstr "Preriscaldamento per espulsione"
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Diametro ugello diverso da G-Code. Continuare?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Diametro ugello diverso dal G-Code. Controlla il valore nelle impostazioni. Stampa annullata."
+
+# 
+#: ultralcd.cpp:6597
+msgid "Rename"
+msgstr "Rinomina"
+
+# 
+#: ultralcd.cpp:6593
+msgid "Select"
+msgstr "Seleziona"
+
+# 
+#: ultralcd.cpp:2134
+msgid "Sensor info"
+msgstr "Info Sensore"
+
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Piano"
+
+# 
+#: 
+msgid "Sound     [assist]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5046
+msgid "Z-correct:"
+msgstr "Correzione-Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Z-probe nr.    [1]"
 

lang/po/Firmware_pl.po

@@ -7,8 +7,8 @@ msgstr ""
 "Content-Transfer-Encoding: 8bit\n"
 "Language: pl\n"
 "Project-Id-Version: Prusa-Firmware\n"
-"POT-Creation-Date: čt 7. úno 2019 14:49:46\n"
-"PO-Revision-Date: čt 7. úno 2019 14:49:46\n"
+"POT-Creation-Date: Wed Sep 4 16:14:12 CEST 2019\n"
+"PO-Revision-Date: Wed Sep 4 16:14:12 CEST 2019\n"
 "Language-Team: \n"
 "X-Generator: Poedit 2.0.7\n"
 "X-Poedit-SourceCharset: UTF-8\n"
@@ -21,72 +21,72 @@ msgid " of 4"
 msgstr " z 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " z 9"
 
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3027
 msgid "[0;0] point offset"
 msgstr "[0;0] przesuniecie punktu"
 
 # MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
-#: ultralcd.cpp:4219
-msgid "\x1b[2JCrash detection can\x1b[1;0Hbe turned on only in\x1b[2;0HNormal mode"
-msgstr "\x1b[2JWykrywanie zderzen moze\x1b[1;0Hbyc wlaczone tylko w\x1b[2;0Htrybie Normalnym"
+#: 
+msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
+msgstr "Wykrywanie zderzen\x0amoze byc wlaczone\x0atylko w\x0atrybie Normalnym"
 
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
-#: ultralcd.cpp:4231
-msgid "\x1b[2JWARNING:\x1b[1;0HCrash detection\x1b[2;0Hdisabled in\x1b[3;0HStealth mode"
-msgstr "\x1b[2JUWAGA:\x1b[1;0HWykrywanie zderzen\x1b[2;0Hwylaczone w\x1b[3;0Htrybie Stealth"
+#: 
+msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
+msgstr "UWAGA:\x0aWykrywanie zderzen\x0awylaczone w\x0atrybie Stealth"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2290
 msgid ">Cancel"
-msgstr ""
+msgstr ">Anuluj"
 
-# MSG_BABYSTEPPING_Z c=20
-#: ultralcd.cpp:3043
-msgid "Adjusting Z"
-msgstr "Dostrajanie Z"
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3147
+msgid "Adjusting Z:"
+msgstr "Dostrajanie Z:"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Wszystko OK "
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Gotowe. Udanego drukowania!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1974
 msgid "Ambient"
-msgstr ""
+msgstr "Otoczenie"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2576
 msgid "and press the knob"
 msgstr "i nacisnij pokretlo"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3445
 msgid "Are left and right Z~carriages all up?"
 msgstr "Obydwa konce osi dojechaly do gornych ogranicznikow?"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5114
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin    [wl]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5110
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin    [nd]"
 
-#  MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+# MSG_AUTO_DEPLETE_OFF c=17 r=1
+#: ultralcd.cpp:5118
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [wyl]"
 
@@ -96,32 +96,32 @@ msgid "Auto home"
 msgstr "Auto zerowanie"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6736
 msgid "AutoLoad filament"
 msgstr "AutoLadowanie fil."
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4378
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Autoladowanie filamentu dostepne tylko gdy czujnik filamentu jest wlaczony..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2771
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Autoladowanie filamentu wlaczone, nacisnij pokretlo i wsun filament..."
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Dlugosc osi"
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Os"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Stol / Grzanie"
 
@@ -136,7 +136,7 @@ msgid "Bed Heating"
 msgstr "Grzanie stolu.."
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5682
 msgid "Bed level correct"
 msgstr "Korekta poziomowania stolu"
 
@@ -145,38 +145,28 @@ msgstr "Korekta poziomowania stolu"
 msgid "Bed leveling failed. Sensor didnt trigger. Debris on nozzle? Waiting for reset."
 msgstr "Kalibracja nieudana. Sensor nie aktywowal sie. Zanieczysz. dysza? Czekam na reset."
 
-# MSG_BED_LEVELING_FAILED_PROBE_DISCONNECTED c=20 r=4
-#: Marlin_main.cpp:4508
-msgid "Bed leveling failed. Sensor disconnected or cable broken. Waiting for reset."
-msgstr "Poziomowanie stolu nieudane. Sensor odlacz. lub uszkodz. przewod. Czekam na reset."
-
-# MSG_BED_LEVELING_FAILED_POINT_HIGH c=20 r=4
-#: Marlin_main.cpp:4512
-msgid "Bed leveling failed. Sensor triggered too high. Waiting for reset."
-msgstr "Kalibracja Z nieudana. Sensor aktywowal za wysoko. Czekam na reset."
-
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Stol"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2002
 msgid "Belt status"
 msgstr "Stan paskow"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Wykryto zanik napiecia. Kontynowac?"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
-msgstr ""
+msgstr "Zerowanie osi"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5671
 msgid "Calibrate XYZ"
 msgstr "Kalibracja XYZ"
 
@@ -186,12 +176,12 @@ msgid "Calibrate Z"
 msgstr "Kalibruj Z"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4570
 msgid "Calibrate"
 msgstr "Kalibruj"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibracja XYZ. Przekrec pokretlo, aby przesunac os Z do gornych ogranicznikow. Nacisnij, by potwierdzic."
 
@@ -201,37 +191,32 @@ msgid "Calibrating Z"
 msgstr "Kalibruje Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3408
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibracja XYZ. Przekrec pokretlo, aby przesunac os Z do gornych ogranicznikow. Nacisnij, by potwierdzic."
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:813
 msgid "Calibration done"
 msgstr "Kalibracja OK"
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Kalibracja"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Cancel"
 msgstr "Anuluj"
 
-# MSG_SD_INSERTED
-#: 
-msgid "Card inserted"
-msgstr "Karta wlozona"
-
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Karta wyjeta"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2676
 msgid "Color not correct"
 msgstr "Kolor zanieczysz."
 
@@ -241,7 +226,7 @@ msgid "Cooldown"
 msgstr "Chlodzenie"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4503
 msgid "Copy selected language?"
 msgstr "Skopiowac wybrany jezyk?"
 
@@ -266,27 +251,27 @@ msgid "Crash detected."
 msgstr "Zderzenie wykryte"
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:600
 msgid "Crash detected. Resume print?"
 msgstr "Wykryto zderzenie. Wznowic druk?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Crash"
-msgstr ""
+msgstr "Zderzenie"
 
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5823
 msgid "Current"
 msgstr "Aktualne"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2102
 msgid "Date:"
 msgstr "Data:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5568
 msgid "Disable steppers"
 msgstr "Wylaczenie silnikow"
 
@@ -296,77 +281,52 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Odleglosc dyszy od powierzchni druku nie jest skalibrowana. Postepuj zgodnie z instrukcja: rozdzial Wprowadzenie - Kalibracja pierwszej warstwy."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4984
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Chcesz powtorzyc ostatni krok i ponownie ustawic odleglosc miedzy dysza a stolikiem?"
 
-# MSG_EXTRUDER_CORRECTION c=9
-#: ultralcd.cpp:4889
-msgid "E-correct"
-msgstr "Korekcja E"
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5048
+msgid "E-correct:"
+msgstr "Korekcja E:"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Wysun filament"
 
-# MSG_EJECT_FILAMENT1 c=17 r=1
-#: ultralcd.cpp:5603
-msgid "Eject filament 1"
-msgstr "Wysun filament 1"
-
-# MSG_EJECT_FILAMENT2 c=17 r=1
-#: ultralcd.cpp:5604
-msgid "Eject filament 2"
-msgstr "Wysun filament 2"
-
-# MSG_EJECT_FILAMENT3 c=17 r=1
-#: ultralcd.cpp:5605
-msgid "Eject filament 3"
-msgstr "Wysun filament 3"
-
-# MSG_EJECT_FILAMENT4 c=17 r=1
-#: ultralcd.cpp:5606
-msgid "Eject filament 4"
-msgstr "Wysun filament 4"
-
-# MSG_EJECT_FILAMENT5 c=17 r=1
-#: ultralcd.cpp:5607
-msgid "Eject filament 5"
-msgstr "Wysun filament 5"
-
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Eject"
 msgstr "Wysun"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1434
 msgid "Ejecting filament"
 msgstr "Wysuwanie filamentu"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Krancowka nie aktyw."
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Krancowka"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Krancowki"
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Blad - pamiec statyczna zostala nadpisana"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4391
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "BLAD: Czujnik filamentu nie odpowiada, sprawdz polaczenie."
 
@@ -375,38 +335,13 @@ msgstr "BLAD: Czujnik filamentu nie odpowiada, sprawdz polaczenie."
 msgid "ERROR:"
 msgstr "BLAD:"
 
-# 
-#: Marlin_main.cpp:1006
-msgid "External SPI flash W25X20CL not responding."
-msgstr "Zewnetrzna pamiec flash SPI W25X20CL nie odpowiada."
-
-# 
-#: ultralcd.cpp:5633
-msgid "Extruder 1"
-msgstr "Ekstruder 1"
-
-# 
-#: ultralcd.cpp:5634
-msgid "Extruder 2"
-msgstr "Ekstruder 2"
-
-# 
-#: ultralcd.cpp:5635
-msgid "Extruder 3"
-msgstr "Ekstruder 3"
-
-# 
-#: ultralcd.cpp:5636
-msgid "Extruder 4"
-msgstr "Ekstruder 4"
-
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Went. ekstrudera:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2133
 msgid "Extruder info"
 msgstr "Informacje o ekstruderze"
 
@@ -416,12 +351,12 @@ msgid "Extruder"
 msgstr "Ekstruder"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
-msgstr ""
+msgstr "Bledy MMU"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5082
 msgid "F. autoload  [on]"
 msgstr "Autolad. fil [wl]"
 
@@ -431,14 +366,14 @@ msgid "F. autoload [N/A]"
 msgstr "Autolad.fil.[N/D]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5084
 msgid "F. autoload [off]"
 msgstr "Autolad.fil.[wyl]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
-msgstr ""
+msgstr "Statystyki bledow"
 
 # MSG_FAN_SPEED c=14
 #: messages.c:31
@@ -446,17 +381,17 @@ msgid "Fan speed"
 msgstr "Predkosc went."
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test wentylatora"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5577
 msgid "Fans check   [on]"
 msgstr "Sprawd.went. [wl]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5579
 msgid "Fans check  [off]"
 msgstr "Sprawd.went.[wyl]"
 
@@ -465,13 +400,8 @@ msgstr "Sprawd.went.[wyl]"
 msgid "Fil. sensor  [on]"
 msgstr "Czuj. filam. [wl]"
 
-# MSG_RESPONSE_POOR c=20 r=2
-#: Marlin_main.cpp:3146
-msgid "Fil. sensor response is poor, disable it?"
-msgstr "Reakcja czujnika slaba, wylaczyc?"
-
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5062
 msgid "Fil. sensor [N/A]"
 msgstr "Czuj. filam.[N/D]"
 
@@ -481,9 +411,9 @@ msgid "Fil. sensor [off]"
 msgstr "Czuj. filam.[wyl]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Filam. runouts"
-msgstr ""
+msgstr "Konc. filamentu"
 
 # MSG_FILAMENT_CLEAN c=20 r=2
 #: messages.c:32
@@ -491,32 +421,27 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament wychodzi z dyszy a kolor jest czysty?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2672
 msgid "Filament not loaded"
 msgstr "Fil. nie zaladowany"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Czujnik filamentu"
 
-# MSG_SELFTEST_FILAMENT_SENSOR c=18
-#: ultralcd.cpp:7477
-msgid "Filament sensor:"
-msgstr "Czujnik filamentu:"
-
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2841
 msgid "Filament used"
 msgstr "Uzyty filament"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2841
 msgid "Print time"
 msgstr "Czas druku"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Plik niekompletny. Kontynowac?"
 
@@ -526,52 +451,52 @@ msgid "Finishing movements"
 msgstr "Konczenie druku"
 
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Kal. 1. warstwy"
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4896
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Najpierw wlacze selftest w celu sprawdzenia najczestszych problemow podczas montazu."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Rozwiaz problem i wcisnij przycisk na MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Przeplyw"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2095
 msgid "forum.prusa3d.com"
 msgstr ""
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Przedni went. druku?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3220
 msgid "Front side[um]"
 msgstr "Przod [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Przedni/lewy wentylator"
 
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Grzalka/Termistor"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8468
 msgid "Heating disabled by safety timer."
 msgstr "Grzanie wylaczone przez wyl. czasowy"
 
@@ -586,67 +511,62 @@ msgid "Heating"
 msgstr "Grzanie..."
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4875
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Czesc, jestem Twoja drukarka Original Prusa i3. Czy potrzebujesz pomocy z ustawieniem?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2096
 msgid "howto.prusa3d.com"
 msgstr ""
 
-# 
-#: ultralcd.cpp:6087
-msgid "Change extruder"
-msgstr "Zmiana ekstrudera"
-
 # MSG_FILAMENTCHANGE
 #: messages.c:37
 msgid "Change filament"
 msgstr "Wymiana filamentu"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2587
 msgid "Change success!"
 msgstr "Wymiana ok!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2664
 msgid "Changed correctly?"
 msgstr "Wymiana ok?"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Kontrola stolu"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Kontrola krancowek"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Kontrola hotendu"
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Sprawdzanie czujnikow"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Kontrola osi X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Kontrola osi Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Kontrola osi Z"
 
@@ -666,112 +586,82 @@ msgid "Filament"
 msgstr ""
 
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4905
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Przeprowadze teraz kalibracje XYZ. Zajmie ok. 12 min."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4913
 msgid "I will run z calibration now."
 msgstr "Przeprowadze kalibracje Z."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4978
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Zaczne drukowac linie. Stopniowo opuszczaj dysze przekrecajac pokretlo, poki nie uzyskasz optymalnej wysokosci. Sprawdz obrazki w naszym Podreczniku w rozdz. Kalibracja"
 
-# MSG_IMPROVE_BED_OFFSET_AND_SKEW_LINE1 c=60
-#: mesh_bed_calibration.cpp:2481
-msgid "Improving bed calibration point"
-msgstr "Poprawiam precyzje punktu kalibracyjnego"
-
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Ekran informacyjny"
 
-# MSG_FILAMENT_LOADING_T0 c=20 r=4
-#: messages.c:33
-msgid "Insert filament into extruder 1. Click when done."
-msgstr "Wloz filament do ekstrudera 1. Potwierdz naciskajac pokretlo."
-
-# MSG_FILAMENT_LOADING_T1 c=20 r=4
-#: messages.c:34
-msgid "Insert filament into extruder 2. Click when done."
-msgstr "Wloz filament do ekstrudera 2. Potwierdz naciskajac pokretlo."
-
-# MSG_FILAMENT_LOADING_T2 c=20 r=4
-#: messages.c:35
-msgid "Insert filament into extruder 3. Click when done."
-msgstr "Wloz filament do ekstrudera 3. Potwierdz naciskajac pokretlo."
-
-# MSG_FILAMENT_LOADING_T3 c=20 r=4
-#: messages.c:36
-msgid "Insert filament into extruder 4. Click when done."
-msgstr "Wloz filament do ekstrudera 4. Potwierdz naciskajac pokretlo."
-
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:4938
 msgid "Is filament 1 loaded?"
 msgstr "Filament 1 zaladowany?"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2572
 msgid "Insert filament"
 msgstr "Wprowadz filament"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4941
 msgid "Is filament loaded?"
 msgstr "Filament jest zaladowany?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4972
 msgid "Is it PLA filament?"
 msgstr "Czy to filament PLA?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4704
 msgid "Is PLA filament loaded?"
 msgstr "Fialment PLA jest zaladowany?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "Czy plyta stal. jest na podgrzew. stole?"
 
-# MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
-#: mesh_bed_calibration.cpp:2223
-msgid "Iteration "
-msgstr "Iteracja "
-
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1840
 msgid "Last print failures"
-msgstr ""
+msgstr "Ostatnie bledy druku"
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1823
 msgid "Last print"
-msgstr ""
+msgstr "Ost. wydruk"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Lewy went hotendu?"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2970
 msgid "Left"
 msgstr "Lewa"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3218
 msgid "Left side [um]"
 msgstr "Lewo [um]"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5594
 msgid "Lin. correction"
 msgstr "Korekcja lin."
 
@@ -786,7 +676,7 @@ msgid "Load filament"
 msgstr "Ladowanie fil."
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2612
 msgid "Loading color"
 msgstr "Czyszcz. koloru"
 
@@ -796,92 +686,92 @@ msgid "Loading filament"
 msgstr "Laduje filament"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Luzne kolo pasowe"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6719
 msgid "Load to nozzle"
 msgstr "Zaladuj do dyszy"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Kal. 1. warstwy"
 
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Menu glowne"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Okreslam wysokosc odniesienia punktu kalibracyjnego"
 
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5677
 msgid "Mesh Bed Leveling"
 msgstr "Poziomowanie stolu wg siatki"
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Wznawianie pozycji."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Wznawiam nagrzewanie..."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3005
 msgid "Measured skew"
 msgstr "Zmierzony skos"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU fails"
-msgstr ""
+msgstr "Bledy MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1613
 msgid "MMU load failed     "
-msgstr ""
+msgstr "Blad ladowania MMU"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1840
 msgid "MMU load fails"
-msgstr ""
+msgstr "Bledy ladow. MMU"
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Wznawianie..."
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Tryb   [normalny]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Tryb      [cichy]"
 
 # 
-#: mmu.cpp:635
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU wymaga uwagi uzytkownika."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "MMU power fails"
-msgstr ""
+msgstr "Zaniki zasil. MMU"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Tryb    [Stealth]"
 
@@ -891,62 +781,62 @@ msgid "Mode [auto power]"
 msgstr "Tryb [automatycz]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Tryb[wysoka wyd.]"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2108
 msgid "MMU2 connected"
-msgstr ""
+msgstr "MMU podlaczone"
 
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Silnik"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5566
 msgid "Move axis"
 msgstr "Ruch osi"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4294
 msgid "Move X"
 msgstr "Ruch osi X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4295
 msgid "Move Y"
 msgstr "Ruch osi Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4296
 msgid "Move Z"
 msgstr "Ruch osi Z"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5291
 msgid "No move."
 msgstr "Brak ruchu."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6686
 msgid "No SD card"
 msgstr "Brak karty SD"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2976
 msgid "N/A"
-msgstr ""
+msgstr "N/D"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Nie"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Nie podlaczono "
 
@@ -955,78 +845,73 @@ msgstr "Nie podlaczono "
 msgid "New firmware version available:"
 msgstr "Dostepna nowa wersja firmware:"
 
-# 
-#: 
-msgid "No "
-msgstr "Nie"
-
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Nie kreci sie"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4977
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Kalibruje odleglosc miedzy koncowka dyszy a powierzchnia druku."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4921
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Nagrzewam dysze dla PLA."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Dysza"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1519
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Znaleziono stare ustawienia. Zostana przywrocone domyslne ust. PID, Esteps, itp."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4912
 msgid "Now remove the test print from steel sheet."
 msgstr "Teraz zdejmij wydruk testowy ze stolu."
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:1782
 msgid "Nozzle FAN"
-msgstr ""
+msgstr "Went. hotendu"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6649
 msgid "Pause print"
 msgstr "Wstrzymanie wydruku"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1598
 msgid "PID cal.           "
 msgstr "Kalibracja PID"
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1604
 msgid "PID cal. finished"
 msgstr "Kal. PID zakonczona"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5683
 msgid "PID calibration"
 msgstr "Kalibracja PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:843
 msgid "PINDA Heating"
 msgstr "Grzanie sondy PINDA"
 
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Umiesc kartke papieru na stole roboczym i podczas pomiaru pierwszych 4 punktow. Jesli dysza zahaczy o papier, natychmiast wylacz drukarke."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4986
 msgid "Please clean heatbed and then press the knob."
 msgstr "Oczysc powierzchnie druku i nacisnij pokretlo."
 
@@ -1036,92 +921,92 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Dla prawidl. kalibracji nalezy oczyscic dysze. Potw. guzikiem."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Sprawdz :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Przeczytaj nasz Podrecznik druku 3D aby naprawic problem. Potem wznow Asystenta przez restart drukarki."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4808
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Umiesc filament PLA w ekstruderze i nacisnij pokretlo, aby zaladowac."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4709
 msgid "Please load PLA filament first."
 msgstr "Najpierw zaladuj filament PLA."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3063
 msgid "Please open idler and remove filament manually."
 msgstr "Prosze odciagnac dzwignie dociskowa ekstrudera i recznie usunac filament."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Prosze umiescic plyte stalowa na stole podgrzewanym."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Nacisnij pokretlo aby rozladowac filament"
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4803
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Wsun filament PLA do pierwszej rurki MMU i nacisnij pokretlo aby go zaladowac."
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Wyciagnij filament teraz"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1440
 msgid "Please remove filament and then press the knob."
 msgstr "Wyciagnij filament i wcisnij pokretlo."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Prosze zdjac plyte stalowa z podgrzewanego stolu."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4354
 msgid "Please run XYZ calibration first."
 msgstr "Prosze najpierw uruchomic kalibracje XYZ"
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1359
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Prosze zaktualizowac Firmware MMU2. Czekam na reset."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Prosze czekac"
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4911
 msgid "Please remove shipping helpers first."
 msgstr "Najpierw usun zabezpieczenia transportowe"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Nagrzej dysze!"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6636
 msgid "Preheat"
 msgstr "Grzanie"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Nagrzewanie dyszy. Prosze czekac."
 
@@ -1131,32 +1016,32 @@ msgid "Please upgrade."
 msgstr "Prosze zaktualizowac."
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10365
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Wcisnij pokretlo aby rozgrzac dysze i kontynuowac."
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1876
 msgid "Power failures"
-msgstr ""
+msgstr "Zaniki zasilania"
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Druk przerwany"
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2276
 msgid "Preheating to load"
-msgstr ""
+msgstr "Nagrzew. do ladowania"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2280
 msgid "Preheating to unload"
-msgstr ""
+msgstr "Nagrzew. do rozlad."
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Went. wydruku:"
 
@@ -1166,17 +1051,17 @@ msgid "Print from SD"
 msgstr "Druk z karty SD"
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2206
 msgid "Press the knob"
-msgstr ""
+msgstr "Wcisnij pokretlo"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1061
 msgid "Print paused"
 msgstr "Druk wstrzymany"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Wcisnij pokretlo aby wznowic podgrzewanie dyszy."
 
@@ -1186,102 +1071,87 @@ msgid "Printer has not been calibrated yet. Please follow the manual, chapter Fi
 msgstr "Drukarka nie zostala jeszcze skalibrowana. Kieruj sie Samouczkiem: rozdzial Pierwsze Kroki, sekcja Konfiguracja przed drukowaniem."
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1784
 msgid "Print FAN"
-msgstr ""
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK2.5 ready."
-msgstr "Prusa i3 MK2.5 gotowa"
-
-# WELCOME_MSG c=20
-#: 
-msgid "Prusa i3 MK3 ready."
-msgstr "Prusa i3 MK3 gotowa"
+msgstr "Went. wydruku"
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2094
 msgid "prusa3d.com"
 msgstr ""
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3221
 msgid "Rear side [um]"
 msgstr "Tyl [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9765
 msgid "Recovering print    "
 msgstr "Wznawianie wydruku"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Wyciagnij poprzedni filament i nacisnij pokretlo aby zaladowac nowy."
 
 # 
 #: 
 msgid "Prusa i3 MK3S OK."
-msgstr ""
-
-# 
-#: 
-msgid "Prusa i3 MK2 ready."
-msgstr "Prusa i3 MK2 gotowa"
+msgstr "Prusa i3 MK3S OK"
 
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5688
 msgid "Reset XYZ calibr."
 msgstr "Reset kalibr. XYZ"
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3222
 msgid "Reset"
 msgstr ""
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6656
 msgid "Resume print"
 msgstr "Wznowic wydruk"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Wznawianie druku"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3219
 msgid "Right side[um]"
 msgstr "Prawo [um]"
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5606
 msgid "RPi port     [on]"
 msgstr "Port RPi     [wl]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5604
 msgid "RPi port    [off]"
 msgstr "Port RPi    [wyl]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4726
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Wlaczenie Asystenta usunie obecne dane kalibracyjne i zacznie od poczatku. Kontynuowac?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5236
 msgid "SD card  [normal]"
 msgstr "Karta SD [normal]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5234
 msgid "SD card [flshAir]"
 msgstr "Karta SD[FlshAir]"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2971
 msgid "Right"
 msgstr "Prawa"
 
@@ -1291,217 +1161,207 @@ msgid "Searching bed calibration point"
 msgstr "Szukam punktu kalibracyjnego na stole"
 
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5613
 msgid "Select language"
 msgstr "Wybor jezyka"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Selftest OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Rozpoczynanie Selftestu"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5664
 msgid "Selftest         "
 msgstr "Selftest "
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Blad selftest !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Selftest nieudany"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1551
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Zostanie uruchomiony Selftest aby dokladnie skalibrowac punkt bazowy bez krancowek"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4959
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Wybierz temperature grzania dyszy odpowiednia dla materialu."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4695
 msgid "Select PLA filament:"
 msgstr "Wybierz filament PLA:"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3230
 msgid "Set temperature:"
 msgstr "Ustaw. temperatury:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Ustawienia"
 
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5685
 msgid "Show end stops"
 msgstr "Pokaz krancowki"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:3941
 msgid "Sensor state"
-msgstr ""
-
-# 
-#: 
-msgid "Sensors info"
-msgstr ""
-
-# 
-#: 
-msgid "Show pinda state"
-msgstr "Stan sondy PINDA"
+msgstr "Stan czujnikow"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Niektore pliki nie zostana posortowane. Max. liczba plikow w 1 folderze = 100."
 
 # MSG_SORT_NONE c=17 r=1
-#: ultralcd.cpp:5043
-msgid "Sort:      [none]"
-msgstr "Sortuj:    [brak]"
+#: ultralcd.cpp:5246
+msgid "Sort       [none]"
+msgstr "Sortuj     [brak]"
 
 # MSG_SORT_TIME c=17 r=1
-#: ultralcd.cpp:5041
-msgid "Sort:      [time]"
-msgstr "Sortuj:    [czas]"
+#: ultralcd.cpp:5244
+msgid "Sort       [time]"
+msgstr "Sortuj     [czas]"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3008
 msgid "Severe skew"
 msgstr "Znaczny skos"
 
 # MSG_SORT_ALPHA c=17 r=1
-#: ultralcd.cpp:5042
-msgid "Sort:  [alphabet]"
-msgstr "Sortuj: [alfabet]"
+#: ultralcd.cpp:5245
+msgid "Sort   [alphabet]"
+msgstr "Sortuj  [alfabet]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Sortowanie plikow"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Dzwiek   [Glosny]"
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3007
 msgid "Slight skew"
 msgstr "Lekki skos"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#: 
 msgid "Sound      [mute]"
 msgstr "Dzwiek[Wylaczony]"
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4870
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Wykryto problem, wymuszono poziomowanie osi Z ..."
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Dzwiek    [1-raz]"
 
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Dzwiek    [Cichy]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Predkosc"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Kreci sie"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4367
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Potrzebna jest stabilna temperatura otoczenia 21-26C i stabilne podloze."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statystyki"
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Zatrzymac druk"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ZATRZYMANO."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Wsparcie"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Zamieniono"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Kalibracja temp."
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5600
 msgid "Temp. cal.   [on]"
 msgstr "Kalibr. temp.[wl]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5598
 msgid "Temp. cal.  [off]"
 msgstr "Kalibr.temp.[wyl]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5694
 msgid "Temp. calibration"
 msgstr "Kalibracja temp."
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3867
 msgid "Temperature calibration failed"
 msgstr "Kalibracja temperaturowa nieudana"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Kalibracja temperaturowa zakonczona i wlaczona. Moze byc wylaczona z menu Ustawienia -> Kalibracja temp."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5564
 msgid "Temperature"
 msgstr "Temperatura"
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2140
 msgid "Temperatures"
 msgstr "Temperatury"
 
@@ -1511,127 +1371,122 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Musimy przeprowadzic kalibracje Z. Kieruj sie Samouczkiem: rozdzial Pierwsze Kroki, sekcja Kalibracja."
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2863
 msgid "Total filament"
 msgstr "Calkowita dlugosc filamentu"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2863
 msgid "Total print time"
 msgstr "Calkowity czas druku"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6633
 msgid "Tune"
 msgstr "Strojenie"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4783
 msgid "Unload"
 msgstr "Rozladuj"
 
 # 
-#: ultralcd.cpp:5617
-msgid "Unload all"
-msgstr "Rozladuj wszystkie"
-
-# 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1857
 msgid "Total failures"
-msgstr ""
+msgstr "Suma bledow"
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2213
 msgid "to load filament"
-msgstr ""
+msgstr "aby zaladow. fil."
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2217
 msgid "to unload filament"
-msgstr ""
+msgstr "aby rozlad. filament"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Rozladowanie fil."
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Rozladowuje filament"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1824
 msgid "Total"
-msgstr ""
+msgstr "Suma"
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5822
 msgid "Used during print"
 msgstr "Uzyte podczas druku"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2143
 msgid "Voltages"
 msgstr "Napiecia"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2116
 msgid "unknown"
-msgstr ""
+msgstr "nieznane"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5262
 msgid "Wait for user..."
 msgstr "Czekam na uzytkownika..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3374
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Oczekiwanie na wychlodzenie dyszy i stolu"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3338
 msgid "Waiting for PINDA probe cooling"
 msgstr "Czekam az spadnie temp. sondy PINDA"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4782
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Uzyj opcji Rozladuj jesli filament wystaje z tylnej rurki MMU. Uzyj opcji Wysun jesli wciaz jest w srodku."
 
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1511
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Ostrzezenie: typ drukarki i plyta glowna ulegly zmianie."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1503
 msgid "Warning: motherboard type changed."
 msgstr "Ostrzezenie: plyta glowna ulegla zmianie."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1507
 msgid "Warning: printer type changed."
 msgstr "Ostrzezenie: rodzaj drukarki ulegl zmianie"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3053
 msgid "Was filament unload successful?"
 msgstr "Rozladowanie fil. ok?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Blad polaczenia"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5661
 msgid "Wizard"
 msgstr "Asystent"
 
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2132
 msgid "XYZ cal. details"
 msgstr "Szczegoly kal. XYZ"
 
@@ -1641,107 +1496,312 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Kalibracja XYZ nieudana. Sprawdz przyczyny i rozwiazania w instrukcji."
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Tak"
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Zawsze mozesz uruchomic Asystenta ponownie przez Kalibracja -> Asystent."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3838
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Kalibracja XYZ pomyslna. Skos bedzie automatycznie korygowany."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Kalibracja XYZ prawidlowa. Osie X/Y lekko skosne. Dobra robota!"
 
 # 
-#: ultralcd.cpp:4885
-msgid "X-correct"
-msgstr "Korekcja X"
+#: ultralcd.cpp:5044
+msgid "X-correct:"
+msgstr "Korekcja X:"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3832
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Kalibracja XYZ ok. Osie X/Y sa prostopadle. Gratulacje!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Kalibr. XYZ niedokladna. Przednie punkty kalibr. nieosiagalne."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3819
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Kalibracja XYZ niedokladna. Prawy przedni punkt nieosiagalny."
 
-# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_LEFT_FAR c=20 r=8
-#: ultralcd.cpp:3699
-msgid "XYZ calibration compromised. Left front calibration point not reachable."
-msgstr "Kalibracja XYZ niedokladna. Lewy przedni punkt nieosiagalny."
-
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6080
 msgid "Load all"
 msgstr "Zalad. wszystkie"
 
-# MSG_LOAD_FILAMENT_1 c=17
-#: ultralcd.cpp:5576
-msgid "Load filament 1"
-msgstr "Zaladuj fil. 1"
-
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3798
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Kalibracja XYZ nieudana. Nie znaleziono punktow kalibracyjnych."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Kalibr. XYZ nieudana. Przednie punkty kalibr. nieosiagalne. Nalezy poprawic montaz drukarki."
 
 # 
-#: ultralcd.cpp:3687
-msgid "XYZ calibration failed. Left front calibration point not reachable."
-msgstr "Kalibr. XYZ nieudana. Lewy przedni punkt nieosiagalny. Nalezy poprawic montaz drukarki."
-
-# MSG_LOAD_FILAMENT_2 c=17
-#: ultralcd.cpp:5577
-msgid "Load filament 2"
-msgstr "Zaladuj fil. 2"
-
-# 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3807
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Kalibr. XYZ nieudana. Prawy przedni punkt nieosiagalny. Nalezy poprawic montaz drukarki."
 
-# MSG_LOAD_FILAMENT_3 c=17
-#: ultralcd.cpp:5578
-msgid "Load filament 3"
-msgstr "Zaladuj fil. 3"
-
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2968
 msgid "Y distance from min"
 msgstr "Dystans od 0 w osi Y"
 
 # 
-#: ultralcd.cpp:4886
-msgid "Y-correct"
-msgstr "Korekcja Y"
+#: ultralcd.cpp:5045
+msgid "Y-correct:"
+msgstr "Korekcja Y:"
 
-# MSG_LOAD_FILAMENT_4 c=17
-#: ultralcd.cpp:5579
-msgid "Load filament 4"
-msgstr "Zaladuj fil. 4"
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr ""
+
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Wstecz"
+
+# 
+#: ultralcd.cpp:5553
+msgid "Checks"
+msgstr "Testy"
+
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falszywy alarm"
+
+# 
+#: ultralcd.cpp:3946
+msgid "FINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5459
+msgid "Firmware   [none]"
+msgstr "Firmware   [brak]"
+
+# 
+#: ultralcd.cpp:5465
+msgid "Firmware [strict]"
+msgstr "Firmware [restr.]"
+
+# 
+#: ultralcd.cpp:5462
+msgid "Firmware   [warn]"
+msgstr "Firmware[ostrzez]"
+
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "Ustawienia HW"
+
+# 
+#: ultralcd.cpp:3950
+msgid "IR:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Kor. magnesow [nd]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Kor. magnesow[wyl]"
+
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Kor. magnesow [wl]"
+
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Siatka       [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Siatka       [7x7]"
+
+# 
+#: ultralcd.cpp:5591
+msgid "Mesh bed leveling"
+msgstr "Poziomowanie wg siatki"
 
-# MSG_LOAD_FILAMENT_5 c=17
-#: ultralcd.cpp:5582
-msgid "Load filament 5"
-msgstr "Laduj filament 5"
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5220
+msgid "MMU Mode [Normal]"
+msgstr "Tryb MMU[Normaln]"
+
+# 
+#: ultralcd.cpp:5221
+msgid "MMU Mode[Stealth]"
+msgstr "Tryb MMU [Stealth]"
+
+# 
+#: ultralcd.cpp:4427
+msgid "Mode change in progress ..."
+msgstr "Trwa zmiana trybu..."
+
+# 
+#: ultralcd.cpp:5420
+msgid "Model      [none]"
+msgstr "Model      [brak]"
+
+# 
+#: ultralcd.cpp:5426
+msgid "Model    [strict]"
+msgstr "Model [restrykc.]"
+
+# 
+#: ultralcd.cpp:5423
+msgid "Model      [warn]"
+msgstr "Model  [ostrzez.]"
+
+# 
+#: ultralcd.cpp:5381
+msgid "Nozzle d.  [0.25]"
+msgstr "Sr. dyszy  [0,25]"
+
+# 
+#: ultralcd.cpp:5384
+msgid "Nozzle d.  [0.40]"
+msgstr "Sr. dyszy  [0,40]"
+
+# 
+#: ultralcd.cpp:5387
+msgid "Nozzle d.  [0.60]"
+msgstr "Sr. dyszy  [0,60]"
+
+# 
+#: ultralcd.cpp:5335
+msgid "Nozzle     [none]"
+msgstr "Dysza      [brak]"
+
+# 
+#: ultralcd.cpp:5341
+msgid "Nozzle   [strict]"
+msgstr "Dysza [restrykc.]"
+
+# 
+#: ultralcd.cpp:5338
+msgid "Nozzle     [warn]"
+msgstr "Dysza  [ostrzez.]"
+
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr ""
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr ""
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr ""
+
+# 
+#: ultralcd.cpp:3942
+msgid "PINDA:"
+msgstr ""
+
+# 
+#: ultralcd.cpp:2286
+msgid "Preheating to cut"
+msgstr "Nagrzewanie do obciecia"
+
+# 
+#: ultralcd.cpp:2283
+msgid "Preheating to eject"
+msgstr "Nagrzewanie do wysuniecia"
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Srednica dyszy drukarki rozni sie od tej w G-code. Kontynuowac?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Srednica dyszy rozni sie od tej w G-code. Sprawdz ustawienia. Druk anulowany."
+
+# 
+#: ultralcd.cpp:6597
+msgid "Rename"
+msgstr "Zmien nazwe"
+
+# 
+#: ultralcd.cpp:6593
+msgid "Select"
+msgstr "Wybierz"
+
+# 
+#: ultralcd.cpp:2134
+msgid "Sensor info"
+msgstr "Info o sensorach"
+
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Plyta"
+
+# 
+#: 
+msgid "Sound     [assist]"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr ""
+
+# 
+#: ultralcd.cpp:5046
+msgid "Z-correct:"
+msgstr "Korekcja-Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Pomiar-Z       [1]"
 

lang/po/new/cs.po

@@ -15,7 +15,12 @@ msgstr "\e[2JCrash detekce muze\e[1;0Hbyt zapnuta pouze v\e[2;0HNormal modu"
 # MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
 #: ultralcd.cpp:4231
 msgid "\e[2JWARNING:\e[1;0HCrash detection\e[2;0Hdisabled in\e[3;0HStealth mode"
-msgstr "\e[2JPOZOR:\e[1;0HCrash detekce\e[2;0Hdeaktivovana ve\e[3;0HStealth modu"
+msgstr "\e[2JPOZOR:\e[1;0HCrash detekce\e[2;0Hdeaktivovana ve\e[3;0Htichem modu"
+
+# 
+#: ultralcd.cpp:3913
+msgid "  1"
+msgstr "1"
 
 # MSG_PLANNER_BUFFER_BYTES
 #: Marlin_main.cpp:1184
@@ -48,10 +53,15 @@ msgid " of 4"
 msgstr " z 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " z 9"
 
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr "[vyp]"
+
 # MSG_FACTOR
 #: ultralcd.cpp:6008
 msgid " \002 Fact"
@@ -68,14 +78,19 @@ msgid " \002 Min"
 msgstr " \002 Min"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2294
 msgid ">Cancel"
 msgstr ">Zrusit"
 
 # MSG_BABYSTEPPING_Z c=20
 #: ultralcd.cpp:3043
 msgid "Adjusting Z"
-msgstr "Dostavovani Z"
+msgstr "Doladeni Z"
+
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3144
+msgid "Adjusting Z:"
+msgstr "Doladeni Z:"
 
 # MSG_ALL c=19 r=1
 #: messages.c:11
@@ -83,27 +98,27 @@ msgid "All"
 msgstr "Vse"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Vse OK "
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Vse je hotovo."
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1979
 msgid "Ambient"
 msgstr "Okoli"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2573
 msgid "and press the knob"
 msgstr "a stisknete tlacitko"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3442
 msgid "Are left and right Z~carriages all up?"
 msgstr "Dojely oba Z voziky k~hornimu dorazu?"
 
@@ -133,27 +148,27 @@ msgid "Auto home"
 msgstr "Auto home"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6731
 msgid "AutoLoad filament"
 msgstr "AutoZavedeni fil."
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4375
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Automaticke zavadeni filamentu je dostupne pouze pri zapnutem filament senzoru..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2768
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Automaticke zavadeni filamentu aktivni, stisknete tlacitko a vlozte filament..."
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Osa"
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Delka osy"
 
@@ -167,13 +182,18 @@ msgstr "Babystepping X"
 msgid "Babystepping Y"
 msgstr "Babystepping Y"
 
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Zpet"
+
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Podlozka"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Podlozka / Topeni"
 
@@ -188,7 +208,7 @@ msgid "Bed Heating"
 msgstr "Zahrivani bed"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5663
 msgid "Bed level correct"
 msgstr "Korekce podlozky"
 
@@ -213,17 +233,17 @@ msgid "Begin file list"
 msgstr "Pocatek seznamu souboru"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2007
 msgid "Belt status"
 msgstr "Stav remenu"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Detekovan vypadek proudu.Obnovit tisk?"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4566
 msgid "Calibrate"
 msgstr "Zkalibrovat"
 
@@ -233,7 +253,7 @@ msgid "Calibrate E"
 msgstr "Kalibrovat E"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5652
 msgid "Calibrate XYZ"
 msgstr "Kalibrace XYZ"
 
@@ -243,12 +263,12 @@ msgid "Calibrate Z"
 msgstr "Kalibrovat Z"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
 msgstr "Kalibruji vychozi poz."
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibrace XYZ. Otacenim tlacitka posunte Z osu az k~hornimu dorazu. Potvrdte tlacitkem."
 
@@ -258,22 +278,22 @@ msgid "Calibrating Z"
 msgstr "Kalibruji Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibrace Z. Otacenim tlacitka posunte Z osu az k~hornimu dorazu. Potvrdte tlacitkem."
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Kalibrace"
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:832
 msgid "Calibration done"
 msgstr "Kalibrace OK"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Cancel"
 msgstr "Zrusit"
 
@@ -293,7 +313,7 @@ msgid "Card inserted"
 msgstr "Karta vlozena"
 
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Karta vyjmuta"
 
@@ -313,12 +333,12 @@ msgid "Change SD card"
 msgstr "Vymenit SD"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2584
 msgid "Change success!"
 msgstr "Zmena uspesna!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2661
 msgid "Changed correctly?"
 msgstr "Vymena ok?"
 
@@ -328,40 +348,45 @@ msgid "Changing filament!"
 msgstr "Vymena filamentu!"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Kontrola podlozky"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Kontrola endstopu"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Kontrola hotend "
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Kontrola senzoru"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Kontrola osy X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Kontrola osy Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Kontrola osy Z"
 
+# 
+#: ultralcd.cpp:5537
+msgid "Checks"
+msgstr "Kontrola"
+
 # MSG_ERR_CHECKSUM_MISMATCH
 #: cmdqueue.cpp:444
 msgid "checksum mismatch, Last Line: "
@@ -378,7 +403,7 @@ msgid "Choose filament:"
 msgstr "Vyber filament:"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2673
 msgid "Color not correct"
 msgstr "Barva neni cista"
 
@@ -393,12 +418,12 @@ msgid "Copy selected language from XFLASH?"
 msgstr "Kopirovat vybrany jazyk do XFLASH?"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4499
 msgid "Copy selected language?"
 msgstr "Kopirovat vybrany jazyk?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Crash"
 msgstr "Naraz"
 
@@ -423,22 +448,27 @@ msgid "Crash detected."
 msgstr "Detekovan naraz."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:618
 msgid "Crash detected. Resume print?"
 msgstr "Detekovan naraz. Obnovit tisk?"
 
+# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
+#:
+msgid "Crash detection can\nbe turned on only in\nNormal mode"
+msgstr "Crash detekce muze byt zapnuta pouze v Normal modu"
+
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5804
 msgid "Current"
 msgstr "Pouze aktualni"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2106
 msgid "Date:"
 msgstr "Datum:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5552
 msgid "Disable steppers"
 msgstr "Vypnout motory"
 
@@ -448,7 +478,7 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Neni zkalibrovana vzdalenost trysky od tiskove podlozky. Postupujte prosim podle manualu, kapitola Zaciname, odstavec Nastaveni prvni vrstvy."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4968
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Chcete opakovat posledni krok a pozmenit vzdalenost mezi tryskou a podlozkou?"
 
@@ -462,13 +492,18 @@ msgstr "E kalibrace ukoncena. Prosim ocistete trysku. Pote potvrdte tlacitkem."
 msgid "E-correct"
 msgstr "Korekce E"
 
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5032
+msgid "E-correct:"
+msgstr "Korekce E:"
+
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Eject"
 msgstr "Vysunout"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Vysunout filament"
 
@@ -498,7 +533,7 @@ msgid "Eject filament 5"
 msgstr "Vysunout filament 5"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1435
 msgid "Ejecting filament"
 msgstr "Vysouvam filament"
 
@@ -508,17 +543,17 @@ msgid "End file list"
 msgstr "Konec sezn. souboru"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Koncovy spinac"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Kon. spinac nesepnut"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Konc. spinace"
 
@@ -538,7 +573,7 @@ msgid "enqueing \""
 msgstr "zarazovani \""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Chyba - Doslo k prepisu staticke pameti!"
 
@@ -553,7 +588,7 @@ msgid "ERROR:"
 msgstr "CHYBA:"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4388
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "CHYBA: Filament senzor nereaguje, zkontrolujte zapojeni."
 
@@ -588,17 +623,17 @@ msgid "Extruder 4"
 msgstr "Extruder 4"
 
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Levy vent.:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2137
 msgid "Extruder info"
 msgstr "Extruder info"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5066
 msgid "F. autoload  [on]"
 msgstr "F. autozav. [zap]"
 
@@ -608,37 +643,42 @@ msgid "F. autoload [N/A]"
 msgstr "F. autozav. [N/A]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5068
 msgid "F. autoload [off]"
 msgstr "F. autozav. [vyp]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr "Selhani"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
 msgstr "Selhani MMU"
 
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falesne spusteni"
+
 # MSG_FAN_SPEED c=14
 #: messages.c:31
 msgid "Fan speed"
 msgstr "Rychlost vent."
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventilatoru"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5561
 msgid "Fans check   [on]"
 msgstr "Kontr. vent.[zap]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5563
 msgid "Fans check  [off]"
 msgstr "Kontr. vent.[vyp]"
 
@@ -653,7 +693,7 @@ msgid "Fil. sensor response is poor, disable it?"
 msgstr "Senzor nerozpoznal filament, vypnout?"
 
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5046
 msgid "Fil. sensor [N/A]"
 msgstr "Fil. senzor [N/A]"
 
@@ -663,9 +703,9 @@ msgid "Fil. sensor [off]"
 msgstr "Fil. senzor [vyp]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Filam. runouts"
-msgstr "Vypadky filamentu"
+msgstr "Vypadky filam."
 
 # MSG_FILAMENT c=17 r=1
 #: messages.c:30
@@ -678,12 +718,12 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament vytlacen a spravne barvy?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2669
 msgid "Filament not loaded"
 msgstr "Filament nezaveden"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Senzor filamentu"
 
@@ -693,7 +733,7 @@ msgid "Filament sensor:"
 msgstr "Senzor filamentu:"
 
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2838
 msgid "Filament used"
 msgstr "Spotrebovano filamentu"
 
@@ -703,7 +743,7 @@ msgid "Filament used:  "
 msgstr "Filament : "
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Soubor nekompletni. Pokracovat?"
 
@@ -717,53 +757,93 @@ msgstr "Soubor otevren:"
 msgid "File selected"
 msgstr "Soubor vybran"
 
+# 
+#: ultralcd.cpp:3943
+msgid "FINDA:"
+msgstr "FINDA:"
+
 # MSG_FINISHING_MOVEMENTS c=20 r=1
 #: messages.c:40
 msgid "Finishing movements"
 msgstr "Dokoncovani pohybu"
 
+# 
+#: ultralcd.cpp:5443
+msgid "Firmware   [none]"
+msgstr "Firmware [Zadne]"
+
+# 
+#: ultralcd.cpp:5446
+msgid "Firmware   [warn]"
+msgstr "Firmware [Varovat]"
+
+# 
+#: ultralcd.cpp:5449
+msgid "Firmware [strict]"
+msgstr "Firmware [Prisne]"
+
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Kal. prvni vrstvy"
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4880
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Nejdriv pomoci selftestu zkontoluji nejcastejsi chyby vznikajici pri sestaveni tiskarny."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Opravte chybu a pote stisknete tlacitko na jednotce MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Prutok"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2099
 msgid "forum.prusa3d.com"
 msgstr "forum.prusa3d.com"
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Predni tiskovy vent?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3217
 msgid "Front side[um]"
 msgstr "Vpredu [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Predni/levy vent."
 
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr "G-code je pripraven pro jiny typ tiskarny. Pokracovat?"
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr "G-code je pripraven pro jiny typ tiskarny. Prosim preslicujte model znovu. Tisk zrusen."
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr "G-code je pripraven pro novejsi firmware. Pokracovat?"
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr "G-code je pripraven pro novejsi firmware. Prosim aktualizujte firmware. Tisk zrusen."
+
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Topeni/Termistor"
 
@@ -773,7 +853,7 @@ msgid "Heating"
 msgstr "Zahrivani"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8411
 msgid "Heating disabled by safety timer."
 msgstr "Zahrivani preruseno bezpecnostnim casovacem."
 
@@ -783,27 +863,32 @@ msgid "Heating done."
 msgstr "Zahrivani OK."
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4859
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Dobry den, jsem vase tiskarna Original Prusa i3. Chcete abych Vas provedla kalibracnim procesem?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2100
 msgid "howto.prusa3d.com"
 msgstr "howto.prusa3d.com"
 
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "HW nastaveni"
+
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4889
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Nyni provedu xyz kalibraci. Zabere to priblizne 12 min."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4897
 msgid "I will run z calibration now."
 msgstr "Nyni provedu z kalibraci."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4962
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Zacnu tisknout linku a Vy budete postupne snizovat trysku otacenim tlacitka dokud nedosahnete optimalni vysky. Prohlednete si obrazky v nasi prirucce v kapitole Kalibrace."
 
@@ -813,7 +898,7 @@ msgid "Improving bed calibration point"
 msgstr "Zlepsuji presnost kalibracniho bodu"
 
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Informace"
 
@@ -823,7 +908,7 @@ msgid "Init. SD card"
 msgstr "Inic. SD"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2569
 msgid "Insert filament"
 msgstr "Vlozte filament"
 
@@ -848,27 +933,32 @@ msgid "Insert filament into extruder 4. Click when done."
 msgstr "Vlozte filament do extruderu 4. Potvrdte tlacitkem."
 
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:3947
+msgid "IR:"
+msgstr "IR:"
+
+# 
+#: ultralcd.cpp:4922
 msgid "Is filament 1 loaded?"
 msgstr "Je filament 1 zaveden?"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4925
 msgid "Is filament loaded?"
 msgstr "Je filament zaveden?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4956
 msgid "Is it PLA filament?"
 msgstr "Je to PLA filament?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4701
 msgid "Is PLA filament loaded?"
 msgstr "Je PLA filament zaveden?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "Je tiskovy plat na podlozce?"
 
@@ -883,27 +973,27 @@ msgid "KILLED. "
 msgstr "ZRUSENO."
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1828
 msgid "Last print"
 msgstr "Posledni tisk"
 
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1845
 msgid "Last print failures"
 msgstr "Selhani posl. tisku"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2967
 msgid "Left"
 msgstr "Vlevo:"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Levy vent na trysce?"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3215
 msgid "Left side [um]"
 msgstr "Vlevo [um]"
 
@@ -913,7 +1003,7 @@ msgid "Left:"
 msgstr "Vlevo:"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5575
 msgid "Lin. correction"
 msgstr "Korekce lin."
 
@@ -923,7 +1013,7 @@ msgid "Live adjust Z"
 msgstr "Doladeni osy Z"
 
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6059
 msgid "Load all"
 msgstr "Zavest vse"
 
@@ -958,12 +1048,12 @@ msgid "Load filament 5"
 msgstr "Zavest filament 5"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6714
 msgid "Load to nozzle"
 msgstr "Zavest do trysky"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2609
 msgid "Loading color"
 msgstr "Cisteni barvy"
 
@@ -973,7 +1063,7 @@ msgid "Loading filament"
 msgstr "Zavadeni filamentu"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Uvolnena remenicka"
 
@@ -993,7 +1083,7 @@ msgid "M109 Invalid extruder "
 msgstr "M109 Neplatny extruder "
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Kal. prvni vrstvy"
 
@@ -1012,8 +1102,23 @@ msgstr "M218 Neplatny extruder "
 msgid "M221 Invalid extruder "
 msgstr "M221 Neplatny extruder "
 
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Komp. magnetu[Zap]"
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Komp. magnetu[N/A]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Komp. magnetu[Vyp]"
+
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Hlavni nabidka"
 
@@ -1023,42 +1128,77 @@ msgid "Mark filament 100mm from extruder body. Click when done."
 msgstr "Oznacte filament 100 mm od tela extruderu a pote potvrdte tlacitkem."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3002
 msgid "Measured skew"
 msgstr "Merene zkoseni"
 
 # MSG_MEASURED_SKEW c=15 r=1
 #: ultralcd.cpp:2335
 msgid "Measured skew:"
-msgstr "Merene zkoseni:"
+msgstr "Merene zkos.:"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Merim referencni vysku kalibracniho bodu"
 
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Mesh [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Mesh [7x7]"
+
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5658
 msgid "Mesh Bed Leveling"
 msgstr "Mesh Bed Leveling"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:5572
+msgid "Mesh bed leveling"
+msgstr "Mesh Bed Leveling"
+
+# 
+#: Marlin_main.cpp:881
+msgid "MK3 firmware detected on MK3S printer"
+msgstr "MK3 firmware detekovan na tiskarne MK3S"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr "MK3S firmware detekovan na tiskarne MK3"
+
+# 
+#: ultralcd.cpp:1845
 msgid "MMU fails"
 msgstr "Selhani MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1617
 msgid "MMU load failed     "
 msgstr "Zavedeni MMU selhalo"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1845
 msgid "MMU load fails"
 msgstr "MMU selhani zavadeni"
 
 # 
-#: mmu.cpp:635
+#: ultralcd.cpp:5204
+msgid "MMU Mode [Normal]"
+msgstr "MMU mod [Normal]"
+
+# 
+#: ultralcd.cpp:5205
+msgid "MMU Mode[Stealth]"
+msgstr "MMU Mod [Tichy]"
+
+# 
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU potrebuje zasah uzivatele."
 
@@ -1068,44 +1208,49 @@ msgid "MMU needs user attention. Fix the issue and then press button on MMU unit
 msgstr "MMU potrebuje zasah uzivatele. Opravte chybu a pote stisknete tlacitko na jednotce MMU."
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Pokracuji v tisku..."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Pokracuji v nahrivani..."
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Pokracuji..."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "MMU power fails"
 msgstr "MMU vypadky proudu"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2112
 msgid "MMU2 connected"
 msgstr "MMU2 pripojeno"
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Mod      [Normal]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Mod       [tichy]"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
-msgstr "Mod       [tichy]"
+msgstr "Mod [Tichy]"
+
+# 
+#: ultralcd.cpp:4424
+msgid "Mode change in progress ..."
+msgstr "Probiha zmena modu..."
 
 # MSG_AUTO_MODE_ON
 #: messages.c:12
@@ -1113,37 +1258,52 @@ msgid "Mode [auto power]"
 msgstr "Mod [automaticky]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Mod  [vys. vykon]"
 
+# 
+#: ultralcd.cpp:5404
+msgid "Model      [none]"
+msgstr "Trideni [Zadne]"
+
+# 
+#: ultralcd.cpp:5407
+msgid "Model      [warn]"
+msgstr "Model [Varovat]"
+
+# 
+#: ultralcd.cpp:5410
+msgid "Model    [strict]"
+msgstr "Model [Prisne]"
+
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Motor"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5550
 msgid "Move axis"
 msgstr "Posunout osu"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4291
 msgid "Move X"
 msgstr "Posunout X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4292
 msgid "Move Y"
 msgstr "Posunout Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4293
 msgid "Move Z"
 msgstr "Posunout Z"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2973
 msgid "N/A"
 msgstr "N/A"
 
@@ -1153,7 +1313,7 @@ msgid "New firmware version available:"
 msgstr "Vysla nova verze firmware:"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Ne"
 
@@ -1168,12 +1328,12 @@ msgid "No Checksum with line number, Last Line: "
 msgstr "Zadny kontrolni soucet s cislem radku, Posl. radek:"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5254
 msgid "No move."
 msgstr "Bez pohybu."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6694
 msgid "No SD card"
 msgstr "Zadna SD karta"
 
@@ -1183,37 +1343,67 @@ msgid "No thermistors - no temperature"
 msgstr "Bez termistoru - bez odectu teploty"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Nezapojeno "
 
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Netoci se"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4961
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Nyni zkalibruji vzdalenost mezi koncem trysky a povrchem podlozky."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4905
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Nyni predehreji trysku pro PLA."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4896
 msgid "Now remove the test print from steel sheet."
 msgstr "Nyni odstrante testovaci vytisk z tiskoveho platu."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Tryska"
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:5319
+msgid "Nozzle     [none]"
+msgstr "Tryska [Zadne]"
+
+# 
+#: ultralcd.cpp:5322
+msgid "Nozzle     [warn]"
+msgstr "Tryska [Varovat]"
+
+# 
+#: ultralcd.cpp:5325
+msgid "Nozzle   [strict]"
+msgstr "Tryska [Prisne]"
+
+# 
+#: ultralcd.cpp:5365
+msgid "Nozzle d.  [0.25]"
+msgstr "Tryska [0.25]"
+
+# 
+#: ultralcd.cpp:5368
+msgid "Nozzle d.  [0.40]"
+msgstr "Tryska [0.40]"
+
+# 
+#: ultralcd.cpp:5371
+msgid "Nozzle d.  [0.60]"
+msgstr "Tryska [0.60]"
+
+# 
+#: ultralcd.cpp:1787
 msgid "Nozzle FAN"
 msgstr "Trysk. vent."
 
@@ -1238,7 +1428,7 @@ msgid "ok"
 msgstr "ok"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1535
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Neplatne hodnoty nastaveni. Bude pouzito vychozi PID, Esteps atd."
 
@@ -1258,7 +1448,7 @@ msgid "openRoot failed"
 msgstr "openRoot selhal"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6657
 msgid "Pause print"
 msgstr "Pozastavit tisk"
 
@@ -1268,42 +1458,47 @@ msgid "Pick print"
 msgstr "Vyberte vytisk"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1613
 msgid "PID cal.           "
 msgstr "PID kal. "
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1619
 msgid "PID cal. finished"
 msgstr "PID kal. ukoncena"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5664
 msgid "PID calibration"
 msgstr "PID kalibrace"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:862
 msgid "PINDA Heating"
 msgstr "Nahrivani PINDA"
 
+# 
+#: ultralcd.cpp:3939
+msgid "PINDA:"
+msgstr "PINDA:"
+
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Umistete list papiru na podlozku a udrzujte jej pod tryskou behem mereni prvnich 4 bodu. Pokud tryska zachyti papir, okamzite vypnete tiskarnu."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Zkontrolujte :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Prosim nahlednete do prirucky 3D tiskare a opravte problem. Pote obnovte Pruvodce restartovanim tiskarny."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4970
 msgid "Please clean heatbed and then press the knob."
 msgstr "Prosim ocistete podlozku a stisknete tlacitko."
 
@@ -1313,12 +1508,12 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Pro uspesnou kalibraci ocistete prosim tiskovou trysku. Potvrdte tlacitkem."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4804
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Prosim vlozte PLA filament do extruderu, pote stisknete tlacitko pro zavedeni filamentu."
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4800
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Prosim vlozte PLA filament do trubicky MMU, pote stisknete tlacitko pro zavedeni filamentu."
 
@@ -1328,52 +1523,52 @@ msgid "Please load PLA filament and then resume Wizard by rebooting the printer.
 msgstr "Prosim zavedte PLA filament a po te obnovte Pruvodce stisknutim reset tlacitka."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4706
 msgid "Please load PLA filament first."
 msgstr "Nejdrive prosim zavedte PLA filament."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3083
 msgid "Please open idler and remove filament manually."
 msgstr "Prosim otevrete idler a manualne odstrante filament."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Umistete prosim tiskovy plat na podlozku"
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Pro vysunuti filamentu stisknete prosim tlacitko"
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Prosim vyjmete urychlene filament"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1441
 msgid "Please remove filament and then press the knob."
 msgstr "Prosim vyjmete filament a pote stisknete tlacitko."
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4895
 msgid "Please remove shipping helpers first."
 msgstr "Nejprve prosim sundejte transportni soucastky."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Odstrante prosim tiskovy plat z podlozky."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4317
 msgid "Please run XYZ calibration first."
 msgstr "Nejprve spustte kalibraci XYZ."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1360
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Prosim aktualizujte firmware ve vasi MMU2 jednotce. Cekam na reset."
 
@@ -1383,12 +1578,12 @@ msgid "Please upgrade."
 msgstr "Prosim aktualizujte."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Prosim cekejte"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Power failures"
 msgstr "Vypadky proudu"
 
@@ -1398,29 +1593,39 @@ msgid "PowerUp"
 msgstr "Zapnuti"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6644
 msgid "Preheat"
 msgstr "Predehrev"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Predehrejte trysku!"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
-msgstr "Predehrivam trysku. Prosim cekejte."
+msgstr "Predehrev trysky. Prosim cekejte."
+
+# 
+#: ultralcd.cpp:2290
+msgid "Preheating to cut"
+msgstr "Predehrev k ustrizeni"
+
+# 
+#: ultralcd.cpp:2287
+msgid "Preheating to eject"
+msgstr "Predehrev k vysunuti"
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2280
 msgid "Preheating to load"
-msgstr "Predehrivam k zavedeni"
+msgstr "Predehrev k zavedeni"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2284
 msgid "Preheating to unload"
-msgstr "Predehrivam k vyjmuti"
+msgstr "Predehrev k vyjmuti"
 
 # MSG_PREPARE_FILAMENT c=20 r=1
 #: ultralcd.cpp:1911
@@ -1428,27 +1633,27 @@ msgid "Prepare new filament"
 msgstr "Pripravte filament"
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10312
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Pro nahrati trysky a pokracovani stisknete tlacitko."
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2210
 msgid "Press the knob"
 msgstr "Stisknete hl. tlacitko"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Pro pokracovani nahrivani trysky stisknete tlacitko."
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Tisk prerusen"
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1789
 msgid "Print FAN"
 msgstr "Tiskovy vent."
 
@@ -1458,7 +1663,7 @@ msgid "Print FAN: "
 msgstr "Tisk. vent:"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Tiskovy vent.:"
 
@@ -1468,12 +1673,12 @@ msgid "Print from SD"
 msgstr "Tisk z SD"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1080
 msgid "Print paused"
 msgstr "Tisk pozastaven"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2838
 msgid "Print time"
 msgstr "Cas tisku"
 
@@ -1487,6 +1692,16 @@ msgstr "Cas tisku: "
 msgid "Printer disconnected"
 msgstr "Tiskarna odpojena"
 
+# 
+#: util.cpp:473
+msgid "Printer FW version differs from the G-code. Continue?"
+msgstr "Firmware tiskarny se lisi od G-code. Pokracovat?"
+
+# 
+#: util.cpp:480
+msgid "Printer FW version differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Firmware tiskarny se lisi od G-code. Prosim zkontrolujte nastaveni. Tisk zrusen."
+
 # MSG_ERR_KILLED
 #: Marlin_main.cpp:7547
 msgid "Printer halted. kill() called!"
@@ -1497,6 +1712,26 @@ msgstr "Tiskarna zastavena. Volano kill()!"
 msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
 msgstr "Tiskarna nebyla jeste zkalibrovana. Postupujte prosim podle manualu, kapitola Zaciname, odstavec Postup kalibrace."
 
+# 
+#: util.cpp:423
+msgid "Printer model differs from the G-code. Continue?"
+msgstr "Model tiskarny se lisi od G-code. Pokracovat?"
+
+# 
+#: util.cpp:430
+msgid "Printer model differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Model tiskarny se lisi od G-code. Prosim zkontrolujte nastaveni. Tisk zrusen."
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Prumer trysky tiskarny se lisi od G-code. Pokracovat?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Prumer trysky tiskarny se lisi od G-code. Prosim zkontrolujte nastaveni. Tisk zrusen."
+
 # MSG_ERR_STOPPED
 #: messages.c:32
 msgid "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
@@ -1512,6 +1747,11 @@ msgstr "Prusa i3 MK2 ok."
 msgid "Prusa i3 MK2.5 ready."
 msgstr "Prusa i3 MK2.5 ok."
 
+# 
+#:
+msgid "Prusa i3 MK3 OK."
+msgstr "Prusa i3 MK3 OK."
+
 # WELCOME_MSG c=20
 #:
 msgid "Prusa i3 MK3 ready."
@@ -1523,17 +1763,17 @@ msgid "Prusa i3 MK3S OK."
 msgstr "Prusa i3 MK3S OK."
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2098
 msgid "prusa3d.com"
 msgstr "prusa3d.com"
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3218
 msgid "Rear side [um]"
 msgstr "Vzadu [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9712
 msgid "Recovering print    "
 msgstr "Obnovovani tisku "
 
@@ -1543,10 +1783,15 @@ msgid "Refresh"
 msgstr "Obnovit"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Vyjmete stary filament a stisknete tlacitko pro zavedeni noveho."
 
+# 
+#: ultralcd.cpp:6605
+msgid "Rename"
+msgstr "Prejmenovat"
+
 # MSG_M119_REPORT
 #: Marlin_main.cpp:5297
 msgid "Reporting endstop status"
@@ -1563,32 +1808,32 @@ msgid "Resend: "
 msgstr "Poslat znovu: "
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3219
 msgid "Reset"
 msgstr "Reset"
 
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5669
 msgid "Reset XYZ calibr."
 msgstr "Reset XYZ kalibr."
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6664
 msgid "Resume print"
 msgstr "Pokracovat"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Obnoveni tisku"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2968
 msgid "Right"
 msgstr "Vpravo"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3216
 msgid "Right side[um]"
 msgstr "Vpravo [um]"
 
@@ -1603,22 +1848,22 @@ msgid "Rotate knob until mark reaches extruder body. Click when done."
 msgstr "Otacejte tlacitkem dokud znacka nedosahne tela extruderu. Potvrdte tlacitkem."
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5587
 msgid "RPi port     [on]"
 msgstr "RPi port    [zap]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5585
 msgid "RPi port    [off]"
 msgstr "RPi port    [vyp]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4723
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Spusteni Pruvodce vymaze ulozene vysledky vsech kalibraci a spusti kalibracni proces od zacatku. Pokracovat?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5220
 msgid "SD card  [normal]"
 msgstr "SD card  [normal]"
 
@@ -1633,7 +1878,7 @@ msgid "SD card [FlshAir]"
 msgstr "SD card [FlshAir]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5218
 msgid "SD card [flshAir]"
 msgstr "SD card [FlshAir]"
 
@@ -1652,53 +1897,63 @@ msgstr "SD printing byte "
 msgid "Searching bed calibration point"
 msgstr "Hledam kalibracni bod podlozky"
 
+# 
+#: ultralcd.cpp:6601
+msgid "Select"
+msgstr "Vybrat"
+
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5594
 msgid "Select language"
 msgstr "Vyber jazyka"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4943
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Vyberte teplotu predehrati trysky ktera odpovida vasemu materialu."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Select PLA filament:"
 msgstr "Vyberte PLA filament:"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Self test OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Self test start "
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5645
 msgid "Selftest         "
 msgstr "Selftest "
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Chyba Selftestu!"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Selftest selhal "
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1567
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Pro kalibraci presneho rehomovani bude nyni spusten selftest."
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:2138
+msgid "Sensor info"
+msgstr "Senzor info"
+
+# 
+#: ultralcd.cpp:3938
 msgid "Sensor state"
 msgstr "Stav senzoru"
 
@@ -1708,17 +1963,17 @@ msgid "Sensors info"
 msgstr "Senzor info"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3227
 msgid "Set temperature:"
 msgstr "Nastavte teplotu:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Nastaveni"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3005
 msgid "Severe skew"
 msgstr "Tezke zkoseni"
 
@@ -1727,8 +1982,13 @@ msgstr "Tezke zkoseni"
 msgid "Severe skew:"
 msgstr "Tezke zkoseni:"
 
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Plech"
+
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5666
 msgid "Show end stops"
 msgstr "Stav konc. spin."
 
@@ -1743,7 +2003,7 @@ msgid "Sleep..."
 msgstr "Spankovy rezim..."
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3004
 msgid "Slight skew"
 msgstr "Lehke zkoseni"
 
@@ -1753,15 +2013,30 @@ msgid "Slight skew:"
 msgstr "Lehke zkoseni:"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Nektere soubory nebudou setrideny. Maximalni pocet souboru ve slozce pro setrideni je 100."
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4833
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Vyskytl se problem, srovnavam osu Z ..."
 
+# MSG_SORT_NONE c=17 r=1
+#: ultralcd.cpp:5230
+msgid "Sort       [none]"
+msgstr "Trideni [Zadne]"
+
+# MSG_SORT_TIME c=17 r=1
+#: ultralcd.cpp:5228
+msgid "Sort       [time]"
+msgstr "Trideni [cas]"
+
+# MSG_SORT_ALPHA c=17 r=1
+#: ultralcd.cpp:5229
+msgid "Sort   [alphabet]"
+msgstr "Trideni [Abeceda]"
+
 # MSG_SORT_NONE c=17 r=1
 #: ultralcd.cpp:4250
 msgid "Sort:      [None]"
@@ -1803,117 +2078,127 @@ msgid "Sort:  [time]"
 msgstr "Trideni [Cas]\n"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Trideni souboru"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Zvuk    [hlasity]"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#:
 msgid "Sound      [mute]"
 msgstr "Zvuk    [vypnuto]"
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Zvuk     [jednou]"
 
+# 
+#:
+msgid "Sound     [assist]"
+msgstr "Zvuk [Asist.]"
+
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Zvuk      [tichy]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Rychlost"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Toci se"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5098
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin   [zap]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5094
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin   [N/A]"
 
 # MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+#: ultralcd.cpp:5102
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [vyp]"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4330
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Je vyzadovana stabilni pokojova teplota 21-26C a pevna podlozka."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistika "
 
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr "Tiskove platy"
+
 # MSG_STEPPER_TOO_HIGH
 #: stepper.cpp:345
 msgid "Steprate too high: "
 msgstr "Krokovani prilis vysoko:"
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Zastavit tisk"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ZASTAVENO."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Podpora"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Prohozene"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Tepl. kal. "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5581
 msgid "Temp. cal.   [on]"
 msgstr "Tepl. kal.  [zap]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5579
 msgid "Temp. cal.  [off]"
 msgstr "Tepl. kal.  [vyp]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5675
 msgid "Temp. calibration"
 msgstr "Teplot. kalibrace"
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5548
 msgid "Temperature"
 msgstr "Teplota"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3864
 msgid "Temperature calibration failed"
 msgstr "Teplotni kalibrace selhala"
 
@@ -1923,12 +2208,12 @@ msgid "Temperature calibration has not been run yet"
 msgstr "Tiskarna nebyla teplotne zkalibrovana"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Teplotni kalibrace dokoncena a je nyni aktivni. Teplotni kalibraci je mozno deaktivovat v menu Nastaveni->Tepl. kal."
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2144
 msgid "Temperatures"
 msgstr "Teploty"
 
@@ -1938,27 +2223,27 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Je potreba kalibrovat osu Z. Prosim postupujte dle prirucky, kapitola Zaciname, sekce Postup kalibrace."
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2217
 msgid "to load filament"
 msgstr "k zavedeni filamentu"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2221
 msgid "to unload filament"
 msgstr "k vyjmuti filamentu"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1829
 msgid "Total"
 msgstr "Celkem"
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "Total failures"
 msgstr "Celkem selhani"
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2860
 msgid "Total filament"
 msgstr "Filament celkem"
 
@@ -1968,7 +2253,7 @@ msgid "Total filament :"
 msgstr "Filament celkem :"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2860
 msgid "Total print time"
 msgstr "Celkovy cas tisku"
 
@@ -1983,17 +2268,17 @@ msgid "TRIGGERED"
 msgstr "AKTIVNI"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6641
 msgid "Tune"
 msgstr "Ladit"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2120
 msgid "unknown"
 msgstr "neznamy"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Unload"
 msgstr "Vysunout"
 
@@ -2003,7 +2288,7 @@ msgid "Unload all"
 msgstr "Vyjmout vse"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Vyjmout filament"
 
@@ -2028,22 +2313,22 @@ msgid "Unload filament 4"
 msgstr "Vyjmout filam. 4"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Vysouvam filament"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4779
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Pouzijte vyjmout pro odstraneni filamentu 1 pokud presahuje z PTFE trubicky za tiskarnou. Pouzijte vysunout, pokud neni videt."
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5803
 msgid "Used during print"
 msgstr "Pouzite behem tisku"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2147
 msgid "Voltages"
 msgstr "Napeti"
 
@@ -2053,32 +2338,37 @@ msgid "volume.init failed"
 msgstr "volume.init selhalo"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5225
 msgid "Wait for user..."
 msgstr "Ceka se na uzivatele..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3371
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Cekani na zchladnuti trysky a podlozky."
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3335
 msgid "Waiting for PINDA probe cooling"
 msgstr "Cekani na zchladnuti PINDA"
 
+# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
+#:
+msgid "WARNING:\nCrash detection\ndisabled in\nStealth mode"
+msgstr "VAROVANI: Crash detekce je zakazana v Tichem rezimu"
+
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1527
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Varovani: doslo ke zmene typu tiskarny a motherboardu."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1519
 msgid "Warning: motherboard type changed."
 msgstr "Varovani: doslo ke zmene typu motherboardu."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1523
 msgid "Warning: printer type changed."
 msgstr "Varovani: doslo ke zmene typu tiskarny."
 
@@ -2088,17 +2378,17 @@ msgid "WARNING: This is an unofficial, unsupported build. Use at your own risk!"
 msgstr "VAROVANI: Neznama, nepodporovana verze firmware. Pouziti na vlastni nebezpeci!"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3072
 msgid "Was filament unload successful?"
 msgstr "Bylo vysunuti filamentu uspesne?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Chyba zapojeni"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5642
 msgid "Wizard"
 msgstr "Pruvodce"
 
@@ -2117,23 +2407,28 @@ msgstr "Zapis do souboru:"
 msgid "X-correct"
 msgstr "Korekce X"
 
+# 
+#: ultralcd.cpp:5028
+msgid "X-correct:"
+msgstr "Korekce X"
+
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2136
 msgid "XYZ cal. details"
 msgstr "Detaily XYZ kal."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Kalibrace XYZ v poradku. Zkoseni bude automaticky vyrovnano pri tisku."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3832
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Kalibrace XYZ v poradku. X/Y osy mirne zkosene. Dobra prace!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3813
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Kalibrace XYZ nepresna. Predni kalibracni body moc vpredu."
 
@@ -2143,17 +2438,17 @@ msgid "XYZ calibration compromised. Left front calibration point not reachable."
 msgstr "Kalibrace XYZ nepresna. Levy predni bod moc vpredu."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Kalibrace XYZ nepresna. Pravy predni bod moc vpredu."
 
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3795
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Kalibrace XYZ selhala. Kalibracni bod podlozky nenalezen."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3801
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Kalibrace XYZ selhala. Predni kalibracni body moc vpredu. Srovnejte tiskarnu."
 
@@ -2168,17 +2463,17 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Kalibrace XYZ selhala. Nahlednete do manualu."
 
 # 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Kalibrace XYZ selhala. Pravy predni bod moc vpredu. Srovnejte tiskarnu."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3829
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Kalibrace XYZ v poradku. X/Y osy jsou kolme. Gratuluji!"
 
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2965
 msgid "Y distance from min"
 msgstr "Y vzdalenost od min"
 
@@ -2192,8 +2487,13 @@ msgstr "Y vzdalenost od min:"
 msgid "Y-correct"
 msgstr "Korekce Y"
 
+# 
+#: ultralcd.cpp:5029
+msgid "Y-correct:"
+msgstr "Korekce Y:"
+
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Ano"
 
@@ -2208,11 +2508,26 @@ msgid "You are using firmware beta version. This is development version. Using t
 msgstr "Pouzivate beta verzi firmwaru. Jedna se o vyvojovou verzi. Pouzivani teto verze firmware neni doporuceno a muze zpusobit poskozeni tiskarny."
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Pruvodce muzete kdykoliv znovu spustit z menu Kalibrace -> Pruvodce"
 
+# 
+#: ultralcd.cpp:5030
+msgid "Z-correct:"
+msgstr "Korekce Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Pocet mereni Z [1]"
+
+# 
+#: ultralcd.cpp:6954
+msgid "Z-probe nr.    [3]"
+msgstr "Pocet mereni Z [3]"
+
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3024
 msgid "[0;0] point offset"
 msgstr "[0;0] odsazeni bodu"

lang/po/new/de.po

@@ -17,6 +17,11 @@ msgstr "\e[2JCrash Erkennung kann\e[1;0Hnur im Modus Normal\e[2;0Hgenutzt werden
 msgid "\e[2JWARNING:\e[1;0HCrash detection\e[2;0Hdisabled in\e[3;0HStealth mode"
 msgstr "\e[2JWARNUNG:\e[1;0HCrash Erkennung\e[2;0Hdeaktiviert im\e[3;0HStealth Modus"
 
+# 
+#: ultralcd.cpp:3913
+msgid "  1"
+msgstr "  1"
+
 # MSG_PLANNER_BUFFER_BYTES
 #: Marlin_main.cpp:1184
 msgid "  PlannerBufferBytes: "
@@ -48,10 +53,15 @@ msgid " of 4"
 msgstr " von 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " von 9"
 
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr "[aus]"
+
 # MSG_FACTOR
 #: ultralcd.cpp:6008
 msgid " \002 Fact"
@@ -68,7 +78,7 @@ msgid " \002 Min"
 msgstr " \002 Min"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2294
 msgid ">Cancel"
 msgstr ">Abbruch"
 
@@ -77,33 +87,38 @@ msgstr ">Abbruch"
 msgid "Adjusting Z"
 msgstr "Z wurde eingestellt"
 
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3144
+msgid "Adjusting Z:"
+msgstr "Z Anpassen:"
+
 # MSG_ALL c=19 r=1
 #: messages.c:11
 msgid "All"
 msgstr "Alle"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Alles richtig "
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Alles abgeschlossen. Viel Spass beim Drucken!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1979
 msgid "Ambient"
 msgstr "Raumtemp."
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2573
 msgid "and press the knob"
 msgstr "und Knopf druecken"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3442
 msgid "Are left and right Z~carriages all up?"
 msgstr "Sind linke+rechte Z- Schlitten ganz oben?"
 
@@ -133,27 +148,27 @@ msgid "Auto home"
 msgstr "Startposition"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6731
 msgid "AutoLoad filament"
 msgstr "Auto-Laden Filament"
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4375
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Automatisches Laden Filament nur bei einge schaltetem Filament- sensor verfuegbar..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2768
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Automatisches Laden Filament ist aktiv, Knopf druecken und Filament einlegen..."
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Achse"
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Achsenlaenge"
 
@@ -167,13 +182,18 @@ msgstr "Babystepping X"
 msgid "Babystepping Y"
 msgstr "Babystepping Y"
 
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Zurueck"
+
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Bett"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Bett / Heizung"
 
@@ -188,7 +208,7 @@ msgid "Bed Heating"
 msgstr "Bett aufwaermen"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5663
 msgid "Bed level correct"
 msgstr "Ausgleich Bett ok"
 
@@ -213,17 +233,17 @@ msgid "Begin file list"
 msgstr "Beginn Dateiliste"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2007
 msgid "Belt status"
 msgstr "Gurtstatus"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Stromausfall! Druck wiederherstellen?"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4566
 msgid "Calibrate"
 msgstr "Kalibrieren"
 
@@ -233,7 +253,7 @@ msgid "Calibrate E"
 msgstr "Kalibrierung E"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5652
 msgid "Calibrate XYZ"
 msgstr "Kalibrierung XYZ"
 
@@ -243,12 +263,12 @@ msgid "Calibrate Z"
 msgstr "Kalibrierung Z"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
 msgstr "Kalibriere Start"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "XYZ Kalibrieren: Drehen Sie den Knopf bis der obere Anschlag erreicht wird. Anschliessend den Knopf druecken."
 
@@ -258,22 +278,22 @@ msgid "Calibrating Z"
 msgstr "Kalibrierung Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Z Kalibrieren: Drehen Sie den Knopf bis der obere Anschlag erreicht wird. Anschliessend den Knopf druecken."
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Kalibrierung"
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:832
 msgid "Calibration done"
 msgstr "Kalibrierung OK"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Cancel"
 msgstr "Abbruch"
 
@@ -293,7 +313,7 @@ msgid "Card inserted"
 msgstr "SD Karte eingesetzt"
 
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "SD Karte entfernt"
 
@@ -313,12 +333,12 @@ msgid "Change SD card"
 msgstr "Wechsel SD Karte"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2584
 msgid "Change success!"
 msgstr "Wechsel erfolgr.!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2661
 msgid "Changed correctly?"
 msgstr "Wechsel ok?"
 
@@ -328,40 +348,45 @@ msgid "Changing filament!"
 msgstr "Filament-Wechsel!"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Pruefe Bett "
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Pruefe Endschalter"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Pruefe Duese  "
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Pruefe Sensoren "
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Pruefe X Achse "
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Pruefe Y Achse "
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Pruefe Z Achse "
 
+# 
+#: ultralcd.cpp:5537
+msgid "Checks"
+msgstr "Checks"
+
 # MSG_ERR_CHECKSUM_MISMATCH
 #: cmdqueue.cpp:444
 msgid "checksum mismatch, Last Line: "
@@ -378,7 +403,7 @@ msgid "Choose filament:"
 msgstr "Waehle Filament:"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2673
 msgid "Color not correct"
 msgstr "Falsche Farbe"
 
@@ -393,12 +418,12 @@ msgid "Copy selected language from XFLASH?"
 msgstr "Gewaehlte Sprache vom Xflash kopieren?"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4499
 msgid "Copy selected language?"
 msgstr "Gewaehlte Sprache kopieren?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Crash"
 msgstr "Crash"
 
@@ -423,22 +448,27 @@ msgid "Crash detected."
 msgstr "Crash erkannt."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:618
 msgid "Crash detected. Resume print?"
 msgstr "Crash erkannt. Druck fortfuehren?"
 
+# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
+#:
+msgid "Crash detection can\nbe turned on only in\nNormal mode"
+msgstr "Crash-Erkennung\nkann nur im Normal\nModus erfolgen"
+
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5804
 msgid "Current"
 msgstr "Aktuelles"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2106
 msgid "Date:"
 msgstr "Datum:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5552
 msgid "Disable steppers"
 msgstr "Motoren aus"
 
@@ -448,7 +478,7 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Der Abstand zwischen der Spitze der Duese und dem Bett ist noch nicht eingestellt. Bitte folgen Sie dem Handbuch, Kapitel Erste Schritte, Abschnitt Erste Schicht Kalibrierung."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4968
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Moechten Sie den letzten Schritt wiederholen, um den Abstand zwischen Duese und Druckbett neu einzustellen?"
 
@@ -462,13 +492,18 @@ msgstr "E-Kalibrierung beendet. Bitte reinigen Sie die Duese. Klicken wenn ferti
 msgid "E-correct"
 msgstr "E-Korrektur"
 
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5032
+msgid "E-correct:"
+msgstr "E-Korrektur:"
+
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Eject"
 msgstr "Auswurf"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Filamentauswurf"
 
@@ -498,7 +533,7 @@ msgid "Eject filament 5"
 msgstr "Fil.5 auswerfen"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1435
 msgid "Ejecting filament"
 msgstr "werfe Filament aus"
 
@@ -508,17 +543,17 @@ msgid "End file list"
 msgstr "Ende Dateiliste"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Endanschlag"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Ende nicht getroffen"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Endschalter"
 
@@ -538,7 +573,7 @@ msgid "enqueing \""
 msgstr "In Warteschlange \""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Fehler - statischer Speicher wurde ueberschrieben"
 
@@ -553,7 +588,7 @@ msgid "ERROR:"
 msgstr "FEHLER:"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4388
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "FEHLER: Filament- sensor reagiert nicht, bitte Verbindung pruefen."
 
@@ -588,17 +623,17 @@ msgid "Extruder 4"
 msgstr "Extruder 4"
 
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Extruder Luefter:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2137
 msgid "Extruder info"
 msgstr "Extruder Info"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5066
 msgid "F. autoload  [on]"
 msgstr "F.Autoladen  [an]"
 
@@ -608,37 +643,42 @@ msgid "F. autoload [N/A]"
 msgstr "F. Autoload  [nv]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5068
 msgid "F. autoload [off]"
 msgstr "F. Autoload [aus]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr "Fehlerstatistik"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
 msgstr "MMU-Fehler"
 
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falschtriggerung"
+
 # MSG_FAN_SPEED c=14
 #: messages.c:31
 msgid "Fan speed"
 msgstr "Luefter-Tempo"
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Lueftertest"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5561
 msgid "Fans check   [on]"
 msgstr "Luefter Chk. [an]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5563
 msgid "Fans check  [off]"
 msgstr "Luefter Chk.[aus]"
 
@@ -653,7 +693,7 @@ msgid "Fil. sensor response is poor, disable it?"
 msgstr "Fil. Sensorsignal ist schlecht, ausschalten?"
 
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5046
 msgid "Fil. sensor [N/A]"
 msgstr "Fil. Sensor  [nv]"
 
@@ -663,7 +703,7 @@ msgid "Fil. sensor [off]"
 msgstr "Fil. Sensor [aus]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Filam. runouts"
 msgstr "Filam. Maengel"
 
@@ -678,12 +718,12 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament extrudiert + richtige Farbe?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2669
 msgid "Filament not loaded"
 msgstr "Fil. nicht geladen"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Filamentsensor"
 
@@ -693,7 +733,7 @@ msgid "Filament sensor:"
 msgstr "Filamentsensor:"
 
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2838
 msgid "Filament used"
 msgstr "Filament benutzt"
 
@@ -703,7 +743,7 @@ msgid "Filament used:  "
 msgstr "Filamentverbrauch:  "
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Datei unvollstaendig Trotzdem fortfahren?"
 
@@ -717,53 +757,103 @@ msgstr "Datei geoeffnet: "
 msgid "File selected"
 msgstr "Datei ausgewaehlt"
 
+# 
+#: ultralcd.cpp:3943
+msgid "FINDA:"
+msgstr "FINDA:"
+
 # MSG_FINISHING_MOVEMENTS c=20 r=1
 #: messages.c:40
 msgid "Finishing movements"
 msgstr "Bewegung beenden"
 
+# 
+#: ultralcd.cpp:5443
+msgid "Firmware   [none]"
+msgstr "Firmware   [ohne]"
+
+# 
+#: ultralcd.cpp:5446
+msgid "Firmware   [warn]"
+msgstr "Firmware   [warn]"
+
+# 
+#: ultralcd.cpp:5449
+msgid "Firmware [strict]"
+msgstr "Firmware [streng]"
+
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Erste-Schicht Kal."
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4880
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Zunaechst fuehre ich den Selbsttest durch, um die haeufigsten Probleme beim Zusammenbau zu ueberpruefen."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Beseitigen Sie das Problem und druecken Sie dann den Knopf am MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Durchfluss"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2099
 msgid "forum.prusa3d.com"
 msgstr "forum.prusa3d.com"
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Vorderer Luefter?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3217
 msgid "Front side[um]"
 msgstr "Vorne [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Vorderer/linke Luefter"
 
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr "G-Code ist für einen anderen Level geslict. Fortfahren?"
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr "G-Code ist für einen anderen Level geslict. Bitte slicen Sie das Modell erneut. Druck abgebrochen."
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr "G-Code ist für einen anderen Drucker geslict. Fortfahren?"
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr "G-Code ist für einen anderen Drucker geslict. Bitte slicen Sie das Modell erneut. Druck abgebrochen."
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr "G-Code ist für eine neuere Firmware geslict. Fortfahren?"
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr "G-Code ist für eine neuere Firmware geslict. Bitte die Firmware updaten. Druck abgebrochen."
+
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Heizung/Thermistor"
 
@@ -773,7 +863,7 @@ msgid "Heating"
 msgstr "Aufwaermen"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8411
 msgid "Heating disabled by safety timer."
 msgstr "Heizung durch Sicherheitstimer deaktiviert."
 
@@ -783,27 +873,32 @@ msgid "Heating done."
 msgstr "Aufwaermen OK."
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4859
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Hallo, ich bin Ihr Original Prusa i3 Drucker. Moechten Sie, dass ich Sie durch den Einrich- tungsablauf fuehre?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2100
 msgid "howto.prusa3d.com"
 msgstr "howto.prusa3d.com"
 
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "HW Einstellungen"
+
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4889
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Ich werde jetzt die XYZ-Kalibrierung durchfuehren. Es wird ca. 12 Minuten dauern."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4897
 msgid "I will run z calibration now."
 msgstr "Ich werde jetzt die Z Kalibrierung durchfuehren."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4962
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Ich werde jetzt eine Linie drucken. Waehrend des Druckes koennen Sie die Duese allmaehlich senken, indem Sie den Knopf drehen, bis Sie die optimale Hoehe erreichen. Sehen Sie sich die Bilder in unserem Handbuch im Kapitel Kalibrierung an."
 
@@ -813,7 +908,7 @@ msgid "Improving bed calibration point"
 msgstr "Verbessere Bett Kalibrierpunkt"
 
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Infoanzeige"
 
@@ -823,7 +918,7 @@ msgid "Init. SD card"
 msgstr "Init. SD Karte"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2569
 msgid "Insert filament"
 msgstr "Filament einlegen"
 
@@ -848,27 +943,32 @@ msgid "Insert filament into extruder 4. Click when done."
 msgstr "Filament in Extruder 4 einlegen. Klicken wenn fertig."
 
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:3947
+msgid "IR:"
+msgstr "IR:"
+
+# 
+#: ultralcd.cpp:4922
 msgid "Is filament 1 loaded?"
 msgstr "Wurde Filament 1 geladen?"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4925
 msgid "Is filament loaded?"
 msgstr "Ist das Filament geladen?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4956
 msgid "Is it PLA filament?"
 msgstr "Ist es wirklich PLA Filament?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4701
 msgid "Is PLA filament loaded?"
 msgstr "Ist PLA Filament geladen?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "Liegt das Stahlblech auf dem Heizbett?"
 
@@ -883,27 +983,27 @@ msgid "KILLED. "
 msgstr "ABGEBROCHEN. "
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1828
 msgid "Last print"
 msgstr "Letzter Druck"
 
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1845
 msgid "Last print failures"
 msgstr "Letzte Druckfehler"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2967
 msgid "Left"
 msgstr "Links"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Linker Luefter?"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3215
 msgid "Left side [um]"
 msgstr "Links [um]"
 
@@ -913,7 +1013,7 @@ msgid "Left:"
 msgstr "Links:"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5575
 msgid "Lin. correction"
 msgstr "Lineare Korrektur"
 
@@ -923,7 +1023,7 @@ msgid "Live adjust Z"
 msgstr "Z einstellen"
 
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6059
 msgid "Load all"
 msgstr "Alle laden"
 
@@ -958,12 +1058,12 @@ msgid "Load filament 5"
 msgstr "Filament 5 laden"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6714
 msgid "Load to nozzle"
 msgstr "In Druckduese laden"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2609
 msgid "Loading color"
 msgstr "Lade Farbe"
 
@@ -973,7 +1073,7 @@ msgid "Loading filament"
 msgstr "Filament laedt"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Lose Riemenscheibe"
 
@@ -993,7 +1093,7 @@ msgid "M109 Invalid extruder "
 msgstr "M109 Falscher Extruder "
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Erste-Schicht Kal."
 
@@ -1012,8 +1112,23 @@ msgstr "M218 Falscher Extruder "
 msgid "M221 Invalid extruder "
 msgstr "M221 Falscher Extruder "
 
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Magnet Komp. [An]"
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Magnet Komp. [nv]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Magnet Komp.[Aus]"
+
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Hauptmenue"
 
@@ -1023,7 +1138,7 @@ msgid "Mark filament 100mm from extruder body. Click when done."
 msgstr "Filament 100mm vom Extrudergehaeuse markieren. Klicken wenn Fertig."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3002
 msgid "Measured skew"
 msgstr "Schraeglauf"
 
@@ -1033,117 +1148,172 @@ msgid "Measured skew:"
 msgstr "Schraeglauf:"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Messen der Referenzhoehe des Kalibrierpunktes"
 
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Mesh         [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Mesh         [7x7]"
+
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5658
 msgid "Mesh Bed Leveling"
 msgstr "Mesh Bett Ausgleich"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:5572
+msgid "Mesh bed leveling"
+msgstr "Mesh Bett Ausgleich"
+
+# 
+#: Marlin_main.cpp:881
+msgid "MK3 firmware detected on MK3S printer"
+msgstr "MK3-Firmware auf MK3S-Drucker erkannt"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr "MK3S-Firmware auf MK3-Drucker erkannt"
+
+# 
+#: ultralcd.cpp:1845
 msgid "MMU fails"
 msgstr "MMU Fehler"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1617
 msgid "MMU load failed     "
 msgstr "MMU Ladefehler"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1845
 msgid "MMU load fails"
 msgstr "MMU Ladefehler"
 
 # 
-#: mmu.cpp:635
+#: ultralcd.cpp:5204
+msgid "MMU Mode [Normal]"
+msgstr "MMU Modus[Normal]"
+
+# 
+#: ultralcd.cpp:5205
+msgid "MMU Mode[Stealth]"
+msgstr "MMU Modus[Stealth]"
+
+# 
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU erfordert Benutzereingriff."
 
 # MSG_MMU_NEEDS_ATTENTION c=20 r=4
 #: mmu.cpp:359
 msgid "MMU needs user attention. Fix the issue and then press button on MMU unit."
-msgstr "MMU hat eine Störung. Beseitigen Sie das Problem und drücken Sie den Knopf an der MMU."
+msgstr "MMU hat eine Stoerung. Beseitigen Sie das Problem und druecken Sie den Knopf an der MMU."
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Position    wiederherstellen... "
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Temperatur wiederherstellen..."
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK.  Weiterdrucken..."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "MMU power fails"
 msgstr "MMU Netzfehler"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2112
 msgid "MMU2 connected"
 msgstr "MMU2 verbunden"
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Modus    [Normal]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Modus     [leise]"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Modus   [Stealth]"
 
+# 
+#: ultralcd.cpp:4424
+msgid "Mode change in progress ..."
+msgstr "Moduswechsel erfolgt..."
+
 # MSG_AUTO_MODE_ON
 #: messages.c:12
 msgid "Mode [auto power]"
 msgstr "Modus[Auto Power]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Modus[Hohe Leist]"
 
+# 
+#: ultralcd.cpp:5404
+msgid "Model      [none]"
+msgstr "Modell      [ohne]"
+
+# 
+#: ultralcd.cpp:5407
+msgid "Model      [warn]"
+msgstr "Modell     [warn]"
+
+# 
+#: ultralcd.cpp:5410
+msgid "Model    [strict]"
+msgstr "Modell   [streng]"
+
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Motor"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5550
 msgid "Move axis"
 msgstr "Achse bewegen"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4291
 msgid "Move X"
 msgstr "Bewege X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4292
 msgid "Move Y"
 msgstr "Bewege Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4293
 msgid "Move Z"
 msgstr "Bewege Z"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2973
 msgid "N/A"
 msgstr "N.V."
 
@@ -1153,7 +1323,7 @@ msgid "New firmware version available:"
 msgstr "Neue Firmware- Version verfuegbar:"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Nein"
 
@@ -1168,12 +1338,12 @@ msgid "No Checksum with line number, Last Line: "
 msgstr "Keine Pruefsumme mit Zeilennummer, Letzte Zeile: "
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5254
 msgid "No move."
 msgstr "Keine Bewegung."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6694
 msgid "No SD card"
 msgstr "Keine SD Karte"
 
@@ -1183,37 +1353,67 @@ msgid "No thermistors - no temperature"
 msgstr "Keine Thermistoren - keine Temperatur"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Nicht angeschlossen"
 
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Dreht sich nicht"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4961
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Jetzt werde ich den Abstand zwischen Duesenspitze und Druckbett kalibrieren."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4905
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Jetzt werde ich die Duese fuer PLA vorheizen."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4896
 msgid "Now remove the test print from steel sheet."
 msgstr "Testdruck jetzt von Stahlblech entfernen."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Duese"
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:5319
+msgid "Nozzle     [none]"
+msgstr "Duese      [ohne]"
+
+# 
+#: ultralcd.cpp:5322
+msgid "Nozzle     [warn]"
+msgstr "Duese      [warn]"
+
+# 
+#: ultralcd.cpp:5325
+msgid "Nozzle   [strict]"
+msgstr "Duese    [streng]"
+
+# 
+#: ultralcd.cpp:5365
+msgid "Nozzle d.  [0.25]"
+msgstr "Duese D.   [0.25]"
+
+# 
+#: ultralcd.cpp:5368
+msgid "Nozzle d.  [0.40]"
+msgstr "Duese D.   [0.40]"
+
+# 
+#: ultralcd.cpp:5371
+msgid "Nozzle d.  [0.60]"
+msgstr "Duese D.   [0.60]"
+
+# 
+#: ultralcd.cpp:1787
 msgid "Nozzle FAN"
 msgstr "Duesen Luefter"
 
@@ -1238,7 +1438,7 @@ msgid "ok"
 msgstr "ok"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1535
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Alte Einstellungen gefunden. Standard PID, E-Steps u.s.w. werden gesetzt."
 
@@ -1258,7 +1458,7 @@ msgid "openRoot failed"
 msgstr "Zugriff auf Hauptverzeichnis misslungen"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6657
 msgid "Pause print"
 msgstr "Druck pausieren"
 
@@ -1268,42 +1468,47 @@ msgid "Pick print"
 msgstr "Druck auswaehlen"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1613
 msgid "PID cal.           "
 msgstr "PID Kal.           "
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1619
 msgid "PID cal. finished"
 msgstr "PID Kalib. fertig"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5664
 msgid "PID calibration"
 msgstr "PID Kalibrierung"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:862
 msgid "PINDA Heating"
 msgstr "PINDA erwaermen"
 
+# 
+#: ultralcd.cpp:3939
+msgid "PINDA:"
+msgstr "PINDA:"
+
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Legen Sie ein Blatt Papier unter die Duese waehrend der Kalibrierung der ersten 4 Punkte. Wenn die Duese das Papier erfasst, den Drucker sofort ausschalten."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Bitte pruefe:"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Bitte lesen Sie unser Handbuch und beheben Sie das Problem. Fahren Sie dann mit dem Assistenten fort, indem Sie den Drucker neu starten."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4970
 msgid "Please clean heatbed and then press the knob."
 msgstr "Bitte reinigen Sie das Heizbett und druecken Sie dann den Knopf."
 
@@ -1313,12 +1518,12 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Bitte entfernen Sie ueberstehendes Filament von der Duese. Klicken wenn sauber."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4804
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Legen Sie bitte PLA Filament in den Extruder und druecken Sie den Knopf,  um es zu laden."
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4800
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Legen Sie bitte PLA Filament in den ersten Schlauch der MMU und druecken Sie den Knopf,  um es zu laden."
 
@@ -1328,52 +1533,52 @@ msgid "Please load PLA filament and then resume Wizard by rebooting the printer.
 msgstr "Bitte PLA-Filament\nladen und Assistent\nfortsetzen, indem\nSie den Drucker neu\nstarten."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4706
 msgid "Please load PLA filament first."
 msgstr "Bitte laden Sie zuerst PLA Filament."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3083
 msgid "Please open idler and remove filament manually."
 msgstr "Bitte Spannrolle oeffnen und Fila- ment von Hand entfernen"
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Bitte legen Sie das Stahlblech auf das Heizbett."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Bitte druecken Sie den Knopf um das Filament zu entladen."
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Bitte ziehen Sie das Filament sofort heraus"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1441
 msgid "Please remove filament and then press the knob."
 msgstr "Bitte Filament entfernen und dann den Knopf druecken"
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4895
 msgid "Please remove shipping helpers first."
 msgstr "Bitte zuerst Transportsicherungen entfernen."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Bitte entfernen Sie das Stahlblech vom Heizbett."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4317
 msgid "Please run XYZ calibration first."
 msgstr "Bitte zuerst XYZ Kalibrierung ausfuehren."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1360
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Bitte aktualisieren Sie die Firmware in der MMU2. Warte auf Reset."
 
@@ -1383,12 +1588,12 @@ msgid "Please upgrade."
 msgstr "Bitte aktualisieren."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Bitte warten"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Power failures"
 msgstr "Netzfehler"
 
@@ -1398,27 +1603,37 @@ msgid "PowerUp"
 msgstr "Einschalten"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6644
 msgid "Preheat"
 msgstr "Vorheizen"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Duese vorheizen!"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Vorheizen der Duese. Bitte warten."
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2290
+msgid "Preheating to cut"
+msgstr "Heizen zum Schnitt"
+
+# 
+#: ultralcd.cpp:2287
+msgid "Preheating to eject"
+msgstr "Heizen zum Auswurf"
+
+# 
+#: ultralcd.cpp:2280
 msgid "Preheating to load"
 msgstr "Heizen zum Laden"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2284
 msgid "Preheating to unload"
 msgstr "Heizen zum Entladen"
 
@@ -1428,27 +1643,27 @@ msgid "Prepare new filament"
 msgstr "Filam. bereithalten"
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10312
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Bitte druecken Sie den Knopf um die Duese vorzuheizen und fortzufahren."
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2210
 msgid "Press the knob"
 msgstr "Knopf druecken"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Druecken Sie den Knopf um die Duesentemperatur wiederherzustellen"
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Druck abgebrochen"
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1789
 msgid "Print FAN"
 msgstr "Druckluefter"
 
@@ -1458,7 +1673,7 @@ msgid "Print FAN: "
 msgstr "Druckvent.: "
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Druckvent.:"
 
@@ -1468,12 +1683,12 @@ msgid "Print from SD"
 msgstr "Drucken von SD"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1080
 msgid "Print paused"
 msgstr "Druck pausiert"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2838
 msgid "Print time"
 msgstr "Druckzeit"
 
@@ -1487,6 +1702,26 @@ msgstr "Druckzeit: "
 msgid "Printer disconnected"
 msgstr "Drucker getrennt"
 
+# 
+#: util.cpp:473
+msgid "Printer FW version differs from the G-code. Continue?"
+msgstr "Drucker FW-Version weicht vom G-Code ab. Fortfahren?"
+
+# 
+#: util.cpp:480
+msgid "Printer FW version differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Drucker FW-Version weicht vom G-Code ab. Bitte ueberpruefen Sie den Wert in den Einstellungen. Druck abgebrochen."
+
+# 
+#: util.cpp:506
+msgid "Printer G-code level differs from the G-code. Continue?"
+msgstr "Drucker G-Code Level unterscheidet sich vom G-Code. Fortfahren?"
+
+# 
+#: util.cpp:513
+msgid "Printer G-code level differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Der Drucker-G-Code Level unterscheidet sich vom G-Code. Bitte ueberpruefen Sie den Wert in den Einstellungen. Druck abgebrochen."
+
 # MSG_ERR_KILLED
 #: Marlin_main.cpp:7547
 msgid "Printer halted. kill() called!"
@@ -1497,6 +1732,26 @@ msgstr "Printer gestoppt. kill() aufgerufen!"
 msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
 msgstr "Drucker wurde noch nicht kalibriert. Bitte folgen Sie dem Handbuch, Kapitel Erste Schritte, Abschnitt Kalibrie- rungsablauf."
 
+# 
+#: util.cpp:423
+msgid "Printer model differs from the G-code. Continue?"
+msgstr "Druckermodell unterscheidet sich vom G-Code. Fortfahren?"
+
+# 
+#: util.cpp:430
+msgid "Printer model differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Das Druckermodell unterscheidet sich vom G-Code. Bitte ueberpruefen Sie den Wert in den Einstellungen. Druck abgebrochen."
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Der Durchmesser der Druckerduese weicht vom G-Code ab. Fortfahren?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Der Durchmesser der Druckerduese weicht vom G-Code ab. Bitte ueberpruefen Sie den Wert in den Einstellungen. Druck abgebrochen."
+
 # MSG_ERR_STOPPED
 #: messages.c:32
 msgid "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
@@ -1512,6 +1767,11 @@ msgstr "Prusa i3 MK2 bereit."
 msgid "Prusa i3 MK2.5 ready."
 msgstr "Prusa i3 MK2.5 bereit."
 
+# 
+#:
+msgid "Prusa i3 MK3 OK."
+msgstr "Prusa i3 MK3 OK."
+
 # WELCOME_MSG c=20
 #:
 msgid "Prusa i3 MK3 ready."
@@ -1523,17 +1783,17 @@ msgid "Prusa i3 MK3S OK."
 msgstr "Prusa i3 MK3S OK."
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2098
 msgid "prusa3d.com"
 msgstr "prusa3d.com"
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3218
 msgid "Rear side [um]"
 msgstr "Hinten [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9712
 msgid "Recovering print    "
 msgstr "Druck wiederherst    "
 
@@ -1543,10 +1803,15 @@ msgid "Refresh"
 msgstr "Erneuern"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Entfernen Sie das alte Filament und druecken Sie den Knopf, um das neue zu laden."
 
+# 
+#: ultralcd.cpp:6605
+msgid "Rename"
+msgstr "Umbenennen"
+
 # MSG_M119_REPORT
 #: Marlin_main.cpp:5297
 msgid "Reporting endstop status"
@@ -1563,32 +1828,32 @@ msgid "Resend: "
 msgstr "Wiederholen: "
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3219
 msgid "Reset"
 msgstr "Ruecksetzen"
 
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5669
 msgid "Reset XYZ calibr."
 msgstr "XYZ Kalibr. zuruecksetzen."
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6664
 msgid "Resume print"
 msgstr "Druck fortsetzen"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Druck fortgesetzt"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2968
 msgid "Right"
 msgstr "Rechts"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3216
 msgid "Right side[um]"
 msgstr "Rechts [um]"
 
@@ -1603,22 +1868,22 @@ msgid "Rotate knob until mark reaches extruder body. Click when done."
 msgstr "Knopf drehen bis die Markierung das Extrudergehaeuse erreicht. Klicken wenn fertig."
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5587
 msgid "RPi port     [on]"
 msgstr "RPi Port     [an]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5585
 msgid "RPi port    [off]"
 msgstr "RPi Port    [aus]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4723
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Der Assistent wird die aktuellen Kalibrierungsdaten loeschen und von vorne beginnen. Weiterfahren?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5220
 msgid "SD card  [normal]"
 msgstr "SD Karte [normal]"
 
@@ -1633,7 +1898,7 @@ msgid "SD card [FlshAir]"
 msgstr "SD Karte [FlashAir]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5218
 msgid "SD card [flshAir]"
 msgstr "SD Karte[flshAir]"
 
@@ -1652,53 +1917,63 @@ msgstr "SD drucke Byte "
 msgid "Searching bed calibration point"
 msgstr "Suche Bett Kalibrierpunkt"
 
+# 
+#: ultralcd.cpp:6601
+msgid "Select"
+msgstr "Auswahl"
+
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5594
 msgid "Select language"
 msgstr "Waehle Sprache"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4943
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Bitte Vorheiztemperatur auswaehlen, die Ihrem Material entspricht."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Select PLA filament:"
 msgstr "PLA Filament auswaehlen:"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Selbsttest OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Selbsttest start "
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5645
 msgid "Selftest         "
 msgstr "Selbsttest "
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Selbsttest Fehler!"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Selbsttest misslung  "
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1567
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Selbsttest im Gang, um die genaue Rueck- kehr zum Nullpunkt ohne Sensor zu kalibrieren"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:2138
+msgid "Sensor info"
+msgstr "Sensor Info"
+
+# 
+#: ultralcd.cpp:3938
 msgid "Sensor state"
 msgstr "Sensorstatus"
 
@@ -1708,17 +1983,17 @@ msgid "Sensors info"
 msgstr "Sensoren Info"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3227
 msgid "Set temperature:"
 msgstr "Temp. einstellen:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Einstellungen"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3005
 msgid "Severe skew"
 msgstr "Schwerer Schraeglauf"
 
@@ -1727,8 +2002,13 @@ msgstr "Schwerer Schraeglauf"
 msgid "Severe skew:"
 msgstr "Schwerer Verzug:"
 
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Blech"
+
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5666
 msgid "Show end stops"
 msgstr "Endschalter Status"
 
@@ -1743,7 +2023,7 @@ msgid "Sleep..."
 msgstr "Schlafzustand..."
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3004
 msgid "Slight skew"
 msgstr "Leichter Schraeglauf"
 
@@ -1753,15 +2033,30 @@ msgid "Slight skew:"
 msgstr "Etwas verzogen:"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Einige Dateien wur- den nicht sortiert. Max. Dateien pro Verzeichnis = 100."
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4833
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Fehler aufgetreten, Z-Kalibrierung erforderlich..."
 
+# MSG_SORT_NONE c=17 r=1
+#: ultralcd.cpp:5230
+msgid "Sort       [none]"
+msgstr "Sort. [ohne]"
+
+# MSG_SORT_TIME c=17 r=1
+#: ultralcd.cpp:5228
+msgid "Sort       [time]"
+msgstr "Sort. [Zeit]"
+
+# MSG_SORT_ALPHA c=17 r=1
+#: ultralcd.cpp:5229
+msgid "Sort   [alphabet]"
+msgstr "Sort. [Alphabetisch]"
+
 # MSG_SORT_NONE c=17 r=1
 #: ultralcd.cpp:4250
 msgid "Sort:      [None]"
@@ -1803,117 +2098,132 @@ msgid "Sort:  [time]"
 msgstr "Sort.: [Zeit]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Sortiere Dateien"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Sound      [laut]"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#:
 msgid "Sound      [mute]"
 msgstr "Sound     [stumm]"
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Sound    [einmal]"
 
+# 
+#:
+msgid "Sound     [assist]"
+msgstr "Sound     [assist]"
+
+# 
+#: sound.h:9
+msgid "Sound     [blind]"
+msgstr "Sound     [blind]"
+
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Sound     [leise]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Geschwindigkeit"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Dreht sich"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5098
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin    [an]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5094
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin   [N/V]"
 
 # MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+#: ultralcd.cpp:5102
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [aus]"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4330
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Stabile Umgebungs- temperatur 21-26C und feste Stand- flaeche erforderlich"
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistiken "
 
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr "Stahlbleche"
+
 # MSG_STEPPER_TOO_HIGH
 #: stepper.cpp:345
 msgid "Steprate too high: "
 msgstr "Schrittrate zu hoch: "
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Druck abbrechen"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "GESTOPPT. "
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Support"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Ausgetauscht"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Temp Kalib. "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5581
 msgid "Temp. cal.   [on]"
 msgstr "Temp. Kal.   [AN]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5579
 msgid "Temp. cal.  [off]"
 msgstr "Temp. Kal.  [AUS]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5675
 msgid "Temp. calibration"
 msgstr "Temp. kalibrieren"
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5548
 msgid "Temperature"
 msgstr "Temperatur"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3864
 msgid "Temperature calibration failed"
 msgstr "Temperaturkalibrierung fehlgeschlagen"
 
@@ -1923,12 +2233,12 @@ msgid "Temperature calibration has not been run yet"
 msgstr "Temperatur wurde\nnoch nicht\nkalibriert"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Temp.kalibrierung ist fertig + aktiv. Temp.kalibrierung kann ausgeschaltet werden im Menu Einstellungen -> Temp.kal."
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2144
 msgid "Temperatures"
 msgstr "Temperaturen"
 
@@ -1938,27 +2248,27 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Es ist noch notwendig die Z-Kalibrierung auszufuehren. Bitte befolgen Sie das Handbuch, Kapitel Erste Schritte, Abschnitt Kalibrierablauf."
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2217
 msgid "to load filament"
 msgstr "zum Filament laden"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2221
 msgid "to unload filament"
 msgstr "zum Filament entladen"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1829
 msgid "Total"
 msgstr "Gesamt"
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "Total failures"
 msgstr "Gesamte Fehler"
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2860
 msgid "Total filament"
 msgstr "Gesamtes Filament"
 
@@ -1968,7 +2278,7 @@ msgid "Total filament :"
 msgstr "Gesamtes Filament:"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2860
 msgid "Total print time"
 msgstr "Gesamte Druckzeit"
 
@@ -1983,17 +2293,17 @@ msgid "TRIGGERED"
 msgstr "AUSGELOEST"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6641
 msgid "Tune"
 msgstr "Feineinstellung"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2120
 msgid "unknown"
 msgstr "unbekannt"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Unload"
 msgstr "Entladen"
 
@@ -2003,7 +2313,7 @@ msgid "Unload all"
 msgstr "Alles entladen"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Filament entladen"
 
@@ -2028,22 +2338,22 @@ msgid "Unload filament 4"
 msgstr "Filam. 4 entladen"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Filament auswerfen"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4779
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Entladen Sie das Filament 1, wenn er aus dem hinteren MMU-Rohr herausragt. Verwenden Sie den Auswurf, wenn er im Rohr versteckt ist."
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5803
 msgid "Used during print"
 msgstr "Beim Druck benutzt"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2147
 msgid "Voltages"
 msgstr "Spannungen"
 
@@ -2053,32 +2363,37 @@ msgid "volume.init failed"
 msgstr "Dateisystem Init fehlerhaft"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5225
 msgid "Wait for user..."
 msgstr "Warte auf Benutzer.."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3371
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Warten bis Heizung und Bett abgekuehlt sind"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3335
 msgid "Waiting for PINDA probe cooling"
 msgstr "Warten, bis PINDA- Sonde abgekuehlt ist"
 
+# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
+#:
+msgid "WARNING:\nCrash detection\ndisabled in\nStealth mode"
+msgstr "WARNUNG:\nCrash-Erkennung\nim Stealth Modus\nausgeschaltet"
+
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1527
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Warnung: Druckertyp und Platinentyp wurden beide geaendert."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1519
 msgid "Warning: motherboard type changed."
 msgstr "Warnung: Platinentyp wurde geaendert."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1523
 msgid "Warning: printer type changed."
 msgstr "Warnung: Druckertyp wurde geaendert."
 
@@ -2088,17 +2403,17 @@ msgid "WARNING: This is an unofficial, unsupported build. Use at your own risk!"
 msgstr "WARNUNG: Dies ist\neine inoffizielle,\nnicht unterstuetzte\nVersion. Benutzung\nauf eigene Gefahr!"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3072
 msgid "Was filament unload successful?"
 msgstr "Konnten Sie das Filament entnehmen?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Verdrahtungsfehler"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5642
 msgid "Wizard"
 msgstr "Assistent"
 
@@ -2117,23 +2432,28 @@ msgstr "Schreibe in Datei: "
 msgid "X-correct"
 msgstr "X-Korrektur"
 
+# 
+#: ultralcd.cpp:5028
+msgid "X-correct:"
+msgstr "X-Korrektur:"
+
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2136
 msgid "XYZ cal. details"
 msgstr "XYZ Kal. Details"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "XYZ Kalibrierung in Ordnung. Schraeglauf wird automatisch korrigiert."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3832
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "XYZ Kalibrierung in Ordnung. X/Y Achsen sind etwas schraeg."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3813
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "XYZ-Kalibrierung beeintraechtigt. Vordere Kalibrierpunkte nicht erreichbar."
 
@@ -2143,17 +2463,17 @@ msgid "XYZ calibration compromised. Left front calibration point not reachable."
 msgstr "XYZ-Kalibrierung beeintraechtigt. Linker vorderer Kalibrierpunkt nicht erreichbar."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "XYZ-Kalibrierung beeintraechtigt. Rechter vorderer Kalibrierpunkt nicht erreichbar."
 
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3795
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Bett-Kalibrierpunkt nicht gefunden."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3801
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Vordere Kalibrierpunkte nicht erreichbar."
 
@@ -2168,17 +2488,17 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Bitte schauen Sie in das Handbuch."
 
 # 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "XYZ-Kalibrierung fehlgeschlagen. Rechter vorderer Kalibrierpunkt ist nicht erreichbar."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3829
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "XYZ-Kalibrierung ok. X/Y-Achsen sind senkrecht zueinander Glueckwunsch!"
 
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2965
 msgid "Y distance from min"
 msgstr "Y Entfernung vom Min"
 
@@ -2192,8 +2512,13 @@ msgstr "Y Entfernung vom Min:"
 msgid "Y-correct"
 msgstr "Y-Korrektur"
 
+# 
+#: ultralcd.cpp:5029
+msgid "Y-correct:"
+msgstr "Y-Korrektur:"
+
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Ja"
 
@@ -2208,11 +2533,26 @@ msgid "You are using firmware beta version. This is development version. Using t
 msgstr "Sie benutzen eine\nBeta Firmware\nVersion. Dies ist\neine Entwicklungs-\nversion. Die Ver-\nwendung ist nicht\nempfohlen und kann\nzu Schaeden fuehren."
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Sie koennen den Assistenten immer im Menu neu starten: Kalibrierung -> Assistent"
 
+# 
+#: ultralcd.cpp:5030
+msgid "Z-correct:"
+msgstr "Z-Korrektur:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Z-Probe Nr.    [1]"
+
+# 
+#: ultralcd.cpp:6954
+msgid "Z-probe nr.    [3]"
+msgstr "Z-Probe Nr.    [3]"
+
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3024
 msgid "[0;0] point offset"
 msgstr "[0;0] Punktversatz"

lang/po/new/es.po

@@ -17,6 +17,11 @@ msgstr "\e[2JDec. choque\e[1;0Hpuede ser activada solo en\e[2;0HModo normal"
 msgid "\e[2JWARNING:\e[1;0HCrash detection\e[2;0Hdisabled in\e[3;0HStealth mode"
 msgstr "\e[2JATENCION:\e[1;0HDec. choque\e[2;0Hdesactivada en\e[3;0HModo silencio"
 
+# 
+#: ultralcd.cpp:3913
+msgid "  1"
+msgstr "  1"
+
 # MSG_PLANNER_BUFFER_BYTES
 #: Marlin_main.cpp:1184
 msgid "  PlannerBufferBytes: "
@@ -48,10 +53,15 @@ msgid " of 4"
 msgstr " de 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " de 9"
 
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr " [apagado]"
+
 # MSG_FACTOR
 #: ultralcd.cpp:6008
 msgid " \002 Fact"
@@ -68,7 +78,7 @@ msgid " \002 Min"
 msgstr " \002 Min"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2294
 msgid ">Cancel"
 msgstr ">Cancelar"
 
@@ -77,33 +87,38 @@ msgstr ">Cancelar"
 msgid "Adjusting Z"
 msgstr "Ajustar Z"
 
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3144
+msgid "Adjusting Z:"
+msgstr "Ajustando Z:"
+
 # MSG_ALL c=19 r=1
 #: messages.c:11
 msgid "All"
 msgstr "Todos"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Todo bien"
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Terminado! Feliz impresion!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1979
 msgid "Ambient"
 msgstr "Ambiente"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2573
 msgid "and press the knob"
 msgstr "Haz clic"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3442
 msgid "Are left and right Z~carriages all up?"
 msgstr "Carros Z izq./der. estan arriba maximo?"
 
@@ -115,17 +130,17 @@ msgstr "Ajustar Eje Z"
 # MSG_AUTO_DEPLETE_ON c=17 r=1
 #: ultralcd.cpp:4706
 msgid "Auto deplete [on]"
-msgstr "Auto desplegar[on]"
+msgstr "Auto agotar[on]"
 
 # 
 #: ultralcd.cpp:4702
 msgid "Auto deplete[N/A]"
-msgstr "Auto desplegar[N/A]"
+msgstr "Auto agotar[N/A]"
 
 # MSG_AUTO_DEPLETE_OFF c=17 r=1
 #: ultralcd.cpp:4710
 msgid "Auto deplete[off]"
-msgstr "Auto desplegar[off]"
+msgstr "Auto agotar[off]"
 
 # MSG_AUTO_HOME
 #: messages.c:11
@@ -133,27 +148,27 @@ msgid "Auto home"
 msgstr "Llevar al origen"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6731
 msgid "AutoLoad filament"
 msgstr "Carga automatica de filamento"
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4375
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "La carga automatica de filamento solo funciona si el sensor de filamento esta activado..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2768
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "La carga automatica de filamento esta activada, pulse el dial e inserte el filamento..."
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Eje"
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Longitud del eje"
 
@@ -167,13 +182,18 @@ msgstr "Micropasos X"
 msgid "Babystepping Y"
 msgstr "Micropasos Y"
 
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "atras"
+
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Base calefactable "
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Base / Calentador"
 
@@ -188,7 +208,7 @@ msgid "Bed Heating"
 msgstr "Calentando Base"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5663
 msgid "Bed level correct"
 msgstr "Corr. de la cama"
 
@@ -213,17 +233,17 @@ msgid "Begin file list"
 msgstr "Comienzo lista arch. "
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2007
 msgid "Belt status"
 msgstr "Estado de la correa"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Se fue la luz. ?Reanudar la impresion?"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4566
 msgid "Calibrate"
 msgstr "Calibrar"
 
@@ -233,7 +253,7 @@ msgid "Calibrate E"
 msgstr "Calibrar E"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5652
 msgid "Calibrate XYZ"
 msgstr "Calibrar XYZ"
 
@@ -243,12 +263,12 @@ msgid "Calibrate Z"
 msgstr "Calibrar Z"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
 msgstr "Calibrando posicion inicial"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrando XYZ. Gira el dial para subir el extrusor hasta tocar los topes superiores. Despues haz clic."
 
@@ -258,22 +278,22 @@ msgid "Calibrating Z"
 msgstr "Calibrando Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrando Z. Gira el dial para subir el extrusor hasta tocar los topes superiores. Despues haz clic."
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Calibracion"
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:832
 msgid "Calibration done"
 msgstr "Calibracion OK"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Cancel"
 msgstr "Cancelar"
 
@@ -293,7 +313,7 @@ msgid "Card inserted"
 msgstr "Tarjeta insertada"
 
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Tarjeta retirada"
 
@@ -313,12 +333,12 @@ msgid "Change SD card"
 msgstr "Cambiar tarjeta SD"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2584
 msgid "Change success!"
 msgstr "Cambio correcto"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2661
 msgid "Changed correctly?"
 msgstr "Cambio correcto?"
 
@@ -328,44 +348,49 @@ msgid "Changing filament!"
 msgstr "Cambiando filamento"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Control base cal."
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Control endstops"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Control fusor"
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Comprobando los sensores"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Control sensor X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Control sensor Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Control sensor Z"
 
+# 
+#: ultralcd.cpp:5537
+msgid "Checks"
+msgstr "Comprobaciones"
+
 # MSG_ERR_CHECKSUM_MISMATCH
 #: cmdqueue.cpp:444
 msgid "checksum mismatch, Last Line: "
-msgstr "inconcluencia checksum, Ult. Linea: "
+msgstr "error de checksum, Ult. Linea: "
 
 # MSG_CHOOSE_EXTRUDER c=20 r=1
 #: messages.c:49
@@ -378,7 +403,7 @@ msgid "Choose filament:"
 msgstr "Elije filamento:"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2673
 msgid "Color not correct"
 msgstr "Color no homogeneo"
 
@@ -393,12 +418,12 @@ msgid "Copy selected language from XFLASH?"
 msgstr "Copiar idioma seleccionado desde XFLASH?"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4499
 msgid "Copy selected language?"
 msgstr "Copiar idioma seleccionado?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Crash"
 msgstr "Choque"
 
@@ -423,22 +448,27 @@ msgid "Crash detected."
 msgstr "Choque detectado."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:618
 msgid "Crash detected. Resume print?"
 msgstr "Choque detectado. Continuar impresion?"
 
+# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
+#:
+msgid "Crash detection can\nbe turned on only in\nNormal mode"
+msgstr "Detect. choque solo\npuede activarse en\nmodo Normal"
+
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5804
 msgid "Current"
 msgstr "Actual"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2106
 msgid "Date:"
 msgstr "Fecha:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5552
 msgid "Disable steppers"
 msgstr "Apagar motores"
 
@@ -448,7 +478,7 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Distancia entre la punta del boquilla y la superficie de la base aun no fijada. Por favor siga el manual, capitulo Primeros Pasos, Calibracion primera capa."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4968
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Quieres repetir el ultimo paso para reajustar la distancia boquilla-base?"
 
@@ -462,13 +492,18 @@ msgstr "E calibrado. Limpia nozzle. Haz clic una vez terminado."
 msgid "E-correct"
 msgstr "E-correcion"
 
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5032
+msgid "E-correct:"
+msgstr "Correccion-E:"
+
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Eject"
 msgstr "Expulsar"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Expulsar filamento"
 
@@ -498,7 +533,7 @@ msgid "Eject filament 5"
 msgstr "Expulsar filamento 5"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1435
 msgid "Ejecting filament"
 msgstr "Expulsando filamento"
 
@@ -508,17 +543,17 @@ msgid "End file list"
 msgstr "Fin lista arch. "
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Endstop"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Endstop no alcanzado"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Endstops"
 
@@ -538,7 +573,7 @@ msgid "enqueing \""
 msgstr "en cola \""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Error - se ha sobre-escrito la memoria estatica"
 
@@ -553,7 +588,7 @@ msgid "ERROR:"
 msgstr "ERROR:"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4388
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "ERROR: El sensor de filamento no responde, por favor comprueba la conexion."
 
@@ -588,17 +623,17 @@ msgid "Extruder 4"
 msgstr "Extrusor 4"
 
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Ventilador del extrusor:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2137
 msgid "Extruder info"
 msgstr "Informacion del extrusor"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5066
 msgid "F. autoload  [on]"
 msgstr "Autocarg.Fil[act]"
 
@@ -608,37 +643,42 @@ msgid "F. autoload [N/A]"
 msgstr "Autocarg.Fil[N/D]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5068
 msgid "F. autoload [off]"
 msgstr "Autocarg.Fil[ina]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr "Estadistica de fallos"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
 msgstr "Estadistica de fallos MMU"
 
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falsa activación"
+
 # MSG_FAN_SPEED c=14
 #: messages.c:31
 msgid "Fan speed"
 msgstr "Velocidad Vent."
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventiladores"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5561
 msgid "Fans check   [on]"
 msgstr "Comprob.vent[act]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5563
 msgid "Fans check  [off]"
 msgstr "Comprob.vent[ina]"
 
@@ -653,7 +693,7 @@ msgid "Fil. sensor response is poor, disable it?"
 msgstr "La respuesta del sensor de fil es deficiente, ?desactivarlo?"
 
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5046
 msgid "Fil. sensor [N/A]"
 msgstr "Sensor Fil. [N/D]"
 
@@ -663,7 +703,7 @@ msgid "Fil. sensor [off]"
 msgstr "Sensor Fil. [ina]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Filam. runouts"
 msgstr "Filam. acabado"
 
@@ -678,12 +718,12 @@ msgid "Filament extruding & with correct color?"
 msgstr "Es nitido el color nuevo?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2669
 msgid "Filament not loaded"
 msgstr "Fil. no introducido"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Sensor de filamento"
 
@@ -693,7 +733,7 @@ msgid "Filament sensor:"
 msgstr "Sensor de filamento:"
 
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2838
 msgid "Filament used"
 msgstr "Filamento usado"
 
@@ -703,7 +743,7 @@ msgid "Filament used:  "
 msgstr "Filamento usado: "
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Archivo incompleto. ?Continuar de todos modos?"
 
@@ -717,53 +757,103 @@ msgstr "Arch. abierto: "
 msgid "File selected"
 msgstr "Arch. elegido"
 
+# 
+#: ultralcd.cpp:3943
+msgid "FINDA:"
+msgstr "FINDA:"
+
 # MSG_FINISHING_MOVEMENTS c=20 r=1
 #: messages.c:40
 msgid "Finishing movements"
 msgstr "Term. movimientos"
 
+# 
+#: ultralcd.cpp:5443
+msgid "Firmware   [none]"
+msgstr "Firmware   [ninguno]"
+
+# 
+#: ultralcd.cpp:5446
+msgid "Firmware   [warn]"
+msgstr "Firmware   [aviso]"
+
+# 
+#: ultralcd.cpp:5449
+msgid "Firmware [strict]"
+msgstr "Firmware [estricto]"
+
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Cal. primera cap."
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4880
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Primero, hare el Selftest para comprobar los problemas de montaje mas comunes."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Corrige el problema y pulsa el boton en la unidad MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Flujo"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2099
 msgid "forum.prusa3d.com"
 msgstr "forum.prusa3d.com"
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Vent. frontal?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3217
 msgid "Front side[um]"
 msgstr "Frontal [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Ventiladores frontal/izquierdo"
 
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr "Código G laminado para un nivel diferente. ¿Continuar?"
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr "Código G laminado para un nivel diferente. Por favor relamina el modelo de nuevo. Impresión cancelada."
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr "Código G laminado para un tipo de impresora diferente. ¿Continuar?"
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr "Código G laminado para una impresora diferente. Por favor relamina el modelo de nuevo. Impresión cancelada."
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr "Código G laminado para nuevo firmware. ¿Continuar?"
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr "Código G laminado para nuevo firmware. Por favor actualiza el firmware. Impresión cancelada."
+
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Calentador/Termistor"
 
@@ -773,7 +863,7 @@ msgid "Heating"
 msgstr "Calentando..."
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8411
 msgid "Heating disabled by safety timer."
 msgstr "Calentadores desactivados por el temporizador de seguridad."
 
@@ -783,27 +873,32 @@ msgid "Heating done."
 msgstr "Calentamiento acabado."
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4859
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Hola, soy tu impresora Original Prusa i3. Quieres que te guie a traves de la configuracion?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2100
 msgid "howto.prusa3d.com"
 msgstr "howto.prusa3d.com"
 
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "Configuracion HW"
+
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4889
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Hare la calibracion XYZ. Tardara 12 min. aproximadamente."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4897
 msgid "I will run z calibration now."
 msgstr "Voy a hacer Calibracion Z ahora."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4962
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Voy a comenzar a imprimir la linea y tu bajaras el nozzle gradualmente al rotar el dial, hasta que llegues a la altura optima. Mira las imagenes del capitulo Calibracion en el manual."
 
@@ -813,7 +908,7 @@ msgid "Improving bed calibration point"
 msgstr "Mejorando punto de calibracion base"
 
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Monitorizar"
 
@@ -823,7 +918,7 @@ msgid "Init. SD card"
 msgstr "Iniciar tarj. SD"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2569
 msgid "Insert filament"
 msgstr "Introducir filamento"
 
@@ -848,29 +943,34 @@ msgid "Insert filament into extruder 4. Click when done."
 msgstr "Insertar filamento en el extrusor 4. Haz clic una vez terminado."
 
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:3947
+msgid "IR:"
+msgstr "IR:"
+
+# 
+#: ultralcd.cpp:4922
 msgid "Is filament 1 loaded?"
 msgstr "?Esta cargado el filamento 1?"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4925
 msgid "Is filament loaded?"
 msgstr "Esta el filamento cargado?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4956
 msgid "Is it PLA filament?"
 msgstr "Es el filamento PLA?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4701
 msgid "Is PLA filament loaded?"
 msgstr "Esta el filamento PLA cargado?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
-msgstr "?Esta colocada la lamina de acero sobre la base?"
+msgstr "¿Esta colocada la lamina de acero sobre la base?"
 
 # MSG_FIND_BED_OFFSET_AND_SKEW_ITERATION c=20
 #: mesh_bed_calibration.cpp:2223
@@ -883,27 +983,27 @@ msgid "KILLED. "
 msgstr "PARADA DE EMERGENCIA"
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1828
 msgid "Last print"
 msgstr "Ultima impresion"
 
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1845
 msgid "Last print failures"
 msgstr "Ultimas impresiones fallidas"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2967
 msgid "Left"
 msgstr "Izquierda"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Vent. izquierdo?"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3215
 msgid "Left side [um]"
 msgstr "Izquierda [um]"
 
@@ -913,7 +1013,7 @@ msgid "Left:"
 msgstr "Izda:"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5575
 msgid "Lin. correction"
 msgstr "Correccion de Linealidad"
 
@@ -923,7 +1023,7 @@ msgid "Live adjust Z"
 msgstr "Micropaso Eje Z"
 
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6059
 msgid "Load all"
 msgstr "Intr. todos fil."
 
@@ -955,15 +1055,15 @@ msgstr "Introducir fil. 4"
 # MSG_LOAD_FILAMENT_5 c=17
 #: ultralcd.cpp:5582
 msgid "Load filament 5"
-msgstr "Cargar filamento 5"
+msgstr "Introducir fil. 5"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6714
 msgid "Load to nozzle"
 msgstr "Cargar a la boquilla"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2609
 msgid "Loading color"
 msgstr "Cambiando color"
 
@@ -973,7 +1073,7 @@ msgid "Loading filament"
 msgstr "Introduciendo filam."
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Polea suelta"
 
@@ -993,7 +1093,7 @@ msgid "M109 Invalid extruder "
 msgstr "M109 Extrusor invalido"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Cal. primera cap."
 
@@ -1012,8 +1112,23 @@ msgstr "M218 Extrusor invalido"
 msgid "M221 Invalid extruder "
 msgstr "M221 Extrusor invalido"
 
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Comp. imanes [On]"
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Comp. imanes [N/A]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Comp. imanes [Off]"
+
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Menu principal"
 
@@ -1023,7 +1138,7 @@ msgid "Mark filament 100mm from extruder body. Click when done."
 msgstr "Marque el filamento 100 mm por encima del final del extrusor. Haz clic una vez terminado."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3002
 msgid "Measured skew"
 msgstr "Desviacion medida:"
 
@@ -1033,32 +1148,67 @@ msgid "Measured skew:"
 msgstr "Desviación medida:"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Midiendo altura del punto de calibracion"
 
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Malla [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Malla [7x7]"
+
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5658
 msgid "Mesh Bed Leveling"
 msgstr "Nivelacion Mesh Level"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:5572
+msgid "Mesh bed leveling"
+msgstr "Nivelacion Malla Base"
+
+# 
+#: Marlin_main.cpp:881
+msgid "MK3 firmware detected on MK3S printer"
+msgstr "Firmware MK3 detectado en impresora MK3S"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr "Firmware MK3S detectado en impresora MK3"
+
+# 
+#: ultralcd.cpp:1845
 msgid "MMU fails"
 msgstr "Fallos MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1617
 msgid "MMU load failed     "
 msgstr "Carga MMU fallida"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1845
 msgid "MMU load fails"
 msgstr "Carga MMU falla"
 
 # 
-#: mmu.cpp:635
+#: ultralcd.cpp:5204
+msgid "MMU Mode [Normal]"
+msgstr "Modo MMU [Normal]"
+
+# 
+#: ultralcd.cpp:5205
+msgid "MMU Mode[Stealth]"
+msgstr "Modo MMU [Silencioso]"
+
+# 
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU necesita atencion del usuario."
 
@@ -1068,82 +1218,102 @@ msgid "MMU needs user attention. Fix the issue and then press button on MMU unit
 msgstr "MMU necesita atencion del usuario. Corrija el problema y luego presione el boton en la unidad MMU."
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Restaurando posicion..."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Restaurando temperatura..."
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Resumiendo..."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "MMU power fails"
 msgstr "Fallo de energia en MMU"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2112
 msgid "MMU2 connected"
 msgstr "MMU2 conectado"
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Modo     [Normal]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Modo   [silencio]"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Modo   [Silencio]"
 
+# 
+#: ultralcd.cpp:4424
+msgid "Mode change in progress ..."
+msgstr "Cambio de modo progresando ..."
+
 # MSG_AUTO_MODE_ON
 #: messages.c:12
 msgid "Mode [auto power]"
 msgstr "Modo[fuerza auto]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Modo [rend.pleno]"
 
+# 
+#: ultralcd.cpp:5404
+msgid "Model      [none]"
+msgstr "Modelo      [ninguno]"
+
+# 
+#: ultralcd.cpp:5407
+msgid "Model      [warn]"
+msgstr "Modelo [aviso]"
+
+# 
+#: ultralcd.cpp:5410
+msgid "Model    [strict]"
+msgstr "Modelo [estricto]"
+
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Motor"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5550
 msgid "Move axis"
 msgstr "Mover ejes"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4291
 msgid "Move X"
 msgstr "Mover X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4292
 msgid "Move Y"
 msgstr "Mover Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4293
 msgid "Move Z"
 msgstr "Mover Z"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2973
 msgid "N/A"
 msgstr "No disponible"
 
@@ -1153,7 +1323,7 @@ msgid "New firmware version available:"
 msgstr "Nuevo firmware disponible:"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "No"
 
@@ -1168,12 +1338,12 @@ msgid "No Checksum with line number, Last Line: "
 msgstr "Sin Checksum con linea numero, Ult. Linea: "
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5254
 msgid "No move."
 msgstr "Sin movimiento"
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6694
 msgid "No SD card"
 msgstr "No hay tarjeta SD"
 
@@ -1183,37 +1353,67 @@ msgid "No thermistors - no temperature"
 msgstr "Sin termistores - sin temperatura"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "No hay conexion "
 
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Ventilador no gira"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4961
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Voy a calibrar la distancia entre la punta de la boquilla y la superficie de la base."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4905
 msgid "Now I will preheat nozzle for PLA."
-msgstr "Voy a precalentar la boquilla para PLA ahora."
+msgstr "Ahora precalentare la boquilla para PLA ."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4896
 msgid "Now remove the test print from steel sheet."
 msgstr "Ahora retira la prueba de la lamina de acero."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Boquilla"
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:5319
+msgid "Nozzle     [none]"
+msgstr "Nozzle     [ninguno]"
+
+# 
+#: ultralcd.cpp:5322
+msgid "Nozzle     [warn]"
+msgstr "Nozzle     [aviso]"
+
+# 
+#: ultralcd.cpp:5325
+msgid "Nozzle   [strict]"
+msgstr "Nozzle   [estricto]"
+
+# 
+#: ultralcd.cpp:5365
+msgid "Nozzle d.  [0.25]"
+msgstr "Diam. nozzle [0.25]"
+
+# 
+#: ultralcd.cpp:5368
+msgid "Nozzle d.  [0.40]"
+msgstr "Diam. nozzle  [0.40]"
+
+# 
+#: ultralcd.cpp:5371
+msgid "Nozzle d.  [0.60]"
+msgstr "Diam. nozzle  [0.60]"
+
+# 
+#: ultralcd.cpp:1787
 msgid "Nozzle FAN"
 msgstr "Ventilador de capa"
 
@@ -1238,7 +1438,7 @@ msgid "ok"
 msgstr "ok"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1535
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Se han encontrado ajustes anteriores. Se ajustara el PID, los pasos del extrusor, etc"
 
@@ -1258,7 +1458,7 @@ msgid "openRoot failed"
 msgstr "fallo openRoot "
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6657
 msgid "Pause print"
 msgstr "Pausar impresion"
 
@@ -1268,42 +1468,47 @@ msgid "Pick print"
 msgstr "Esc. Modelo Adecuado"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1613
 msgid "PID cal.           "
 msgstr "Cal. PID "
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1619
 msgid "PID cal. finished"
 msgstr "Cal. PID terminada"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5664
 msgid "PID calibration"
 msgstr "Calibracion PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:862
 msgid "PINDA Heating"
 msgstr "Calentando PINDA"
 
+# 
+#: ultralcd.cpp:3939
+msgid "PINDA:"
+msgstr "PINDA:"
+
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Colocar una hoja de papel sobre la superficie de impresion durante la calibracion de los primeros 4 puntos. Si la boquilla mueve el papel, apagar impresora inmediatamente."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Controla :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Lee el manual y resuelve el problema. Despues, reinicia la impresora y continua con el Wizard"
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4970
 msgid "Please clean heatbed and then press the knob."
 msgstr "Limpia la superficie de la base, por favor, y haz clic"
 
@@ -1313,67 +1518,67 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Limpia boquilla para calibracion. Click cuando acabes."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4804
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Inserta, por favor, filamento PLA en el extrusor. Despues haz clic para cargarlo."
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4800
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Por favor introduce el filamento al primer tubo MMU, despues presiona el dial para imprimirlo."
 
 # MSG_WIZARD_INSERT_CORRECT_FILAMENT c=20 r=8
 #: ultralcd.cpp:4109
 msgid "Please load PLA filament and then resume Wizard by rebooting the printer."
-msgstr "Carga filamento PLA, por favor, y reinicia la impresora para continuar con el Wizard"
+msgstr "Carga filamento PLA y reinicia la impresora para continuar con el asistente"
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4706
 msgid "Please load PLA filament first."
 msgstr "Carga el filamento PLA primero por favor."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3083
 msgid "Please open idler and remove filament manually."
 msgstr "Por favor abate el rodillo de empuje (idler) y retira el filamento manualmente."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Por favor coloca la chapa de acero en la base calefactable."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Por favor, pulsa el dial para descargar el filamento"
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Por favor retire el filamento de inmediato"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1441
 msgid "Please remove filament and then press the knob."
 msgstr "Por favor quite el filamento y luego presione el dial."
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4895
 msgid "Please remove shipping helpers first."
 msgstr "Por favor retira los soportes de envio primero."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Por favor retire la chapa de acero de la base calefactable."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4317
 msgid "Please run XYZ calibration first."
 msgstr "Por favor realiza la calibracion XYZ primero."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1360
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Por favor actualice el firmware en tu MMU2. Esperando el reseteo."
 
@@ -1383,12 +1588,12 @@ msgid "Please upgrade."
 msgstr "Actualize por favor"
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Por Favor Espere"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Power failures"
 msgstr "Cortes de energia"
 
@@ -1398,27 +1603,37 @@ msgid "PowerUp"
 msgstr "Encendido"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6644
 msgid "Preheat"
 msgstr "Precalentar"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Precalienta extrusor!"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Precalentando nozzle. Espera por favor."
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2290
+msgid "Preheating to cut"
+msgstr "Precalentando para laminar"
+
+# 
+#: ultralcd.cpp:2287
+msgid "Preheating to eject"
+msgstr "Precalentar para expulsar"
+
+# 
+#: ultralcd.cpp:2280
 msgid "Preheating to load"
 msgstr "Precalentar para cargar"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2284
 msgid "Preheating to unload"
 msgstr "Precalentar para descargar"
 
@@ -1428,52 +1643,52 @@ msgid "Prepare new filament"
 msgstr "Preparar filamento"
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10312
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Pulsa el dial para precalentar la boquilla y continue."
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2210
 msgid "Press the knob"
 msgstr "Pulsa el dial"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Presiona el dial para continuar con la temperatura de la boquilla."
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Impresion cancelada"
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1789
 msgid "Print FAN"
 msgstr "Ventilador del extrusor"
 
-# MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
-msgid "Print fan:"
-msgstr "Ventilador del fusor:"
-
 # MSG_INFO_PRINT_FAN c=11 r=1
 #: ultralcd.cpp:1549
 msgid "Print FAN: "
 msgstr "Ventilador del fusor:"
 
+# MSG_SELFTEST_PRINT_FAN_SPEED c=18
+#: ultralcd.cpp:8221
+msgid "Print fan:"
+msgstr "Ventilador del fusor:"
+
 # MSG_CARD_MENU
 #: messages.c:21
 msgid "Print from SD"
 msgstr "Menu tarjeta SD"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1080
 msgid "Print paused"
 msgstr "Impresion en pausa"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2838
 msgid "Print time"
 msgstr "Tiempo de imp.:"
 
@@ -1487,6 +1702,26 @@ msgstr "Tiempo de imp.:"
 msgid "Printer disconnected"
 msgstr "Impresora desconectada"
 
+# 
+#: util.cpp:473
+msgid "Printer FW version differs from the G-code. Continue?"
+msgstr "FW Impresora difiere de cod.G. ¿Continuar?"
+
+# 
+#: util.cpp:480
+msgid "Printer FW version differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "FW Impresora difiere de cod. G. Comprueba los valores en ajustes. Impresion cancelada."
+
+# 
+#: util.cpp:506
+msgid "Printer G-code level differs from the G-code. Continue?"
+msgstr "Nivel cod.G Impresora difiere de cod.G. ¿Continuar?"
+
+# 
+#: util.cpp:513
+msgid "Printer G-code level differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Nivel cod.G Impresora difiere de cod.G. Comprueba los valores en ajustes. Impresión cancelada."
+
 # MSG_ERR_KILLED
 #: Marlin_main.cpp:7547
 msgid "Printer halted. kill() called!"
@@ -1497,6 +1732,26 @@ msgstr "Impresora detenida. kill() activado!"
 msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
 msgstr "Impresora no esta calibrada todavia. Por favor usa el manual capitulo Primeros pasos Calibracion flujo."
 
+# 
+#: util.cpp:423
+msgid "Printer model differs from the G-code. Continue?"
+msgstr "Modelo Impresora difiere de cod.G. ¿Continuar?"
+
+# 
+#: util.cpp:430
+msgid "Printer model differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Modelo Impresora difiere de cod. G. Comprueba los valores en ajustes. Impresión cancelada."
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Diametro nozzle impresora difiere de cod.G. ¿Continuar?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Diametro nozzle Impresora difiere de cod.G. Comprueba los valores en ajustes. Impresion cancelada."
+
 # MSG_ERR_STOPPED
 #: messages.c:32
 msgid "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
@@ -1512,6 +1767,11 @@ msgstr "Preparado para i3 MK2."
 msgid "Prusa i3 MK2.5 ready."
 msgstr "Preparado para Prusa i3 MK2.5."
 
+# 
+#:
+msgid "Prusa i3 MK3 OK."
+msgstr "Prusa i3 MK3 OK."
+
 # WELCOME_MSG c=20
 #:
 msgid "Prusa i3 MK3 ready."
@@ -1523,17 +1783,17 @@ msgid "Prusa i3 MK3S OK."
 msgstr "Prusa i3 MK3S OK."
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2098
 msgid "prusa3d.com"
 msgstr "prusa3d.es"
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3218
 msgid "Rear side [um]"
 msgstr "Trasera [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9712
 msgid "Recovering print    "
 msgstr "Recuperando impresion"
 
@@ -1543,10 +1803,15 @@ msgid "Refresh"
 msgstr "Refrescar"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Retire el filamento viejo y presione el dial para comenzar a cargar el nuevo filamento."
 
+# 
+#: ultralcd.cpp:6605
+msgid "Rename"
+msgstr "Renombrar"
+
 # MSG_M119_REPORT
 #: Marlin_main.cpp:5297
 msgid "Reporting endstop status"
@@ -1563,32 +1828,32 @@ msgid "Resend: "
 msgstr "Reenviar: "
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3219
 msgid "Reset"
 msgstr "Reset"
 
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5669
 msgid "Reset XYZ calibr."
 msgstr "Reset XYZ calibr."
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6664
 msgid "Resume print"
 msgstr "Reanudar impres."
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
-msgstr "Resumiendo impresion"
+msgstr "Continuando impresion"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2968
 msgid "Right"
 msgstr "Derecha"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3216
 msgid "Right side[um]"
 msgstr "Derecha [um]"
 
@@ -1603,22 +1868,22 @@ msgid "Rotate knob until mark reaches extruder body. Click when done."
 msgstr "Rotar el dial hasta que la marca llegue al cuerpo del extrusor. Haz clic una vez terminado."
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5587
 msgid "RPi port     [on]"
 msgstr "Puerto RPi  [act]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5585
 msgid "RPi port    [off]"
 msgstr "Puerto RPi  [ina]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4723
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Ejecutar el Wizard borrara los valores de calibracion actuales y comenzara de nuevo. Continuar?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5220
 msgid "SD card  [normal]"
 msgstr "Tarj. SD [normal]"
 
@@ -1633,7 +1898,7 @@ msgid "SD card [FlshAir]"
 msgstr "Tarj. SD [FlshAir]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5218
 msgid "SD card [flshAir]"
 msgstr "Tarj. SD[FlshAir]"
 
@@ -1652,53 +1917,63 @@ msgstr "SD byte impresion"
 msgid "Searching bed calibration point"
 msgstr "Buscando punto de calibracion base"
 
+# 
+#: ultralcd.cpp:6601
+msgid "Select"
+msgstr "Seleccionar"
+
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5594
 msgid "Select language"
 msgstr "Cambiar el idioma"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4943
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Selecciona la temperatura para precalentar la boquilla que se ajuste a tu material. "
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Select PLA filament:"
 msgstr "Seleccionar filamento PLA:"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Self test OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Iniciar Selftest"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5645
 msgid "Selftest         "
 msgstr "Selftest"
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Error Selftest !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Fallo Selftest"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1567
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Se realizara el auto-test para calibrar con precision la vuelta a la posicion inicial sin sensores."
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:2138
+msgid "Sensor info"
+msgstr "Info sensor"
+
+# 
+#: ultralcd.cpp:3938
 msgid "Sensor state"
 msgstr "Estado del sensor"
 
@@ -1708,17 +1983,17 @@ msgid "Sensors info"
 msgstr "Informacion sensores"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3227
 msgid "Set temperature:"
 msgstr "Establecer temp.:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Configuracion"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3005
 msgid "Severe skew"
 msgstr "Inclinacion severa"
 
@@ -1727,8 +2002,13 @@ msgstr "Inclinacion severa"
 msgid "Severe skew:"
 msgstr "Inclinación severa:"
 
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Lamina"
+
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5666
 msgid "Show end stops"
 msgstr "Mostrar endstops"
 
@@ -1743,7 +2023,7 @@ msgid "Sleep..."
 msgstr "En reposo..."
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3004
 msgid "Slight skew"
 msgstr "Ligeramente inclinado"
 
@@ -1753,15 +2033,30 @@ msgid "Slight skew:"
 msgstr "Ligeramente inclinado:"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Algunos archivos no se ordenaran. Maximo 100 archivos por carpeta para ordenar. "
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4833
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Problema encontrado, nivelacion Z forzosa ..."
 
+# MSG_SORT_NONE c=17 r=1
+#: ultralcd.cpp:5230
+msgid "Sort       [none]"
+msgstr "Ordenar       [ninguno]"
+
+# MSG_SORT_TIME c=17 r=1
+#: ultralcd.cpp:5228
+msgid "Sort       [time]"
+msgstr "Ordenar       [tiempo]"
+
+# MSG_SORT_ALPHA c=17 r=1
+#: ultralcd.cpp:5229
+msgid "Sort   [alphabet]"
+msgstr "Ordenar   [Alfabetico]"
+
 # MSG_SORT_NONE c=17 r=1
 #: ultralcd.cpp:4250
 msgid "Sort:      [None]"
@@ -1803,117 +2098,132 @@ msgid "Sort:  [time]"
 msgstr "Ordenar: [tiempo]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Ordenando archivos"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Sonido     [alto]"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#:
 msgid "Sound      [mute]"
 msgstr "Sonido[silenciad]"
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Sonido  [una vez]"
 
+# 
+#:
+msgid "Sound     [assist]"
+msgstr "Sonido [asistido]"
+
+# 
+#: sound.h:9
+msgid "Sound     [blind]"
+msgstr "Sonido     [ciego]"
+
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Sonido[silencios]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Velocidad"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Ventilador girando"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5098
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin    [on]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5094
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin   [N/A]"
 
 # MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+#: ultralcd.cpp:5102
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [off]"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4330
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Se necesita una temperatura ambiente ente 21 y 26C y un soporte rigido."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Estadisticas "
 
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr "Lámina de acero"
+
 # MSG_STEPPER_TOO_HIGH
 #: stepper.cpp:345
 msgid "Steprate too high: "
 msgstr "Pasos muy altos: "
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Detener impresion"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "PARADA"
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Soporte"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Intercambiado"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Cal. temp. "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5581
 msgid "Temp. cal.   [on]"
 msgstr "Cal. temp.   [ON]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5579
 msgid "Temp. cal.  [off]"
 msgstr "Cal. temp.  [OFF]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5675
 msgid "Temp. calibration"
 msgstr "Calibracion temp."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5548
 msgid "Temperature"
 msgstr "Temperatura"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3864
 msgid "Temperature calibration failed"
 msgstr "Fallo de la calibracion de temperatura"
 
@@ -1923,12 +2233,12 @@ msgid "Temperature calibration has not been run yet"
 msgstr "La temperatura de calibracion no ha sido ajustada"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Calibracion temperatura terminada. Haz clic para continuar."
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2144
 msgid "Temperatures"
 msgstr "Temperaturas"
 
@@ -1938,27 +2248,27 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Todavia es necesario hacer una calibracion Z. Por favor siga el manual, capitulo Primeros pasos, seccion Calibracion del flujo."
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2217
 msgid "to load filament"
 msgstr "para cargar el filamento"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2221
 msgid "to unload filament"
 msgstr "para descargar el filamento"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1829
 msgid "Total"
 msgstr "Total"
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "Total failures"
 msgstr "Fallos totales"
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2860
 msgid "Total filament"
 msgstr "Filamento total:"
 
@@ -1968,7 +2278,7 @@ msgid "Total filament :"
 msgstr "Filamento total:"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2860
 msgid "Total print time"
 msgstr "Tiempo total :"
 
@@ -1983,17 +2293,17 @@ msgid "TRIGGERED"
 msgstr "ACTIVADO"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6641
 msgid "Tune"
 msgstr "Ajustar"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2120
 msgid "unknown"
 msgstr "desconocido"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Unload"
 msgstr "Descargar"
 
@@ -2003,7 +2313,7 @@ msgid "Unload all"
 msgstr "Soltar todos fil."
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Soltar filamento"
 
@@ -2028,22 +2338,22 @@ msgid "Unload filament 4"
 msgstr "Soltar fil. 4"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Soltando filamento"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4779
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Usa unload para retirar el filamento 1 si sobresale por fuera de la parte trasera del tubo MMU. Usa Expulsar si esta escondido dentro del tubo"
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5803
 msgid "Used during print"
 msgstr "Usado en impresion"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2147
 msgid "Voltages"
 msgstr "Voltajes"
 
@@ -2053,32 +2363,37 @@ msgid "volume.init failed"
 msgstr "fallo volume.init \n"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5225
 msgid "Wait for user..."
 msgstr "Esperando ordenes"
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3371
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Esperando enfriamiento de la base y extrusor."
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3335
 msgid "Waiting for PINDA probe cooling"
 msgstr "Esperando a que se enfrie la sonda PINDA"
 
+# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
+#:
+msgid "WARNING:\nCrash detection\ndisabled in\nStealth mode"
+msgstr "ATENCION:\nDetect. choque \ndesactivada en\nmodo Silencioso"
+
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1527
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Aviso: tanto el tipo de impresora como el tipo de la placa han cambiado."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1519
 msgid "Warning: motherboard type changed."
 msgstr "Cuidado: el tipo de placa ha cambiado."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1523
 msgid "Warning: printer type changed."
 msgstr "Cuidado: Ha cambiado el tipo de impresora."
 
@@ -2088,17 +2403,17 @@ msgid "WARNING: This is an unofficial, unsupported build. Use at your own risk!"
 msgstr "CUIDADO: Esta es una version no-oficial y sin soporte. ¡Usala bajo tu responsabilidad!"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3072
 msgid "Was filament unload successful?"
-msgstr "?Se cargocon exito el filamento?"
+msgstr "?Se cargo con exito el filamento?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Error de conexion"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5642
 msgid "Wizard"
 msgstr "Wizard"
 
@@ -2117,23 +2432,28 @@ msgstr "Escribiendo al arch.: "
 msgid "X-correct"
 msgstr "X-correcion"
 
+# 
+#: ultralcd.cpp:5028
+msgid "X-correct:"
+msgstr "Correccion-X:"
+
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2136
 msgid "XYZ cal. details"
 msgstr "Detalles de calibracion XYZ"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Calibracion XYZ correcta. La inclinacion se corregira automaticamente."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3832
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Calibracion XYZ correcta. Los ejes X / Y estan ligeramente inclinados. Buen trabajo!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3813
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Calibrazion XYZ comprometida. Puntos frontales no alcanzables."
 
@@ -2143,17 +2463,17 @@ msgid "XYZ calibration compromised. Left front calibration point not reachable."
 msgstr "Calibrazion XYZ comprometida. Punto frontal izquierdo no alcanzable."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Calibrazion XYZ comprometida. Punto frontal derecho no alcanzable."
 
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3795
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Calibracion XYZ fallada. Puntos de calibracion en la base no encontrados."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3801
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Calibracion XYZ fallada. Puntos frontales no alcanzables."
 
@@ -2168,17 +2488,17 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Calibracion XYZ fallada. Consulta el manual por favor."
 
 # 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Calibracion XYZ fallad. Punto frontal derecho no alcanzable."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3829
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Calibracion XYZ ok. Ejes X/Y perpendiculares. Enhorabuena!"
 
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2965
 msgid "Y distance from min"
 msgstr "Distancia en Y desde el min"
 
@@ -2190,10 +2510,15 @@ msgstr "Distancia en Y desde el min:"
 # 
 #: ultralcd.cpp:4886
 msgid "Y-correct"
-msgstr "Y-correcion"
+msgstr "Y-correccion"
+
+# 
+#: ultralcd.cpp:5029
+msgid "Y-correct:"
+msgstr "Correccion-Y:"
 
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Si"
 
@@ -2205,14 +2530,29 @@ msgstr "Estas usando una version alpha de firmware. Esta es una version de desar
 # MSG_FW_VERSION_BETA c=20 r=8
 #: Marlin_main.cpp:931
 msgid "You are using firmware beta version. This is development version. Using this version is not recommended and may cause printer damage."
-msgstr "Estás usando una versión beta de firmware. Es una versión en desarrollo. No recomendamos que la uses y podría causar daños a la impresora."
+msgstr "Estas usando una version beta de firmware. Es una version en desarrollo. No recomendamos que la uses y podria causar daños a la impresora."
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Siempre puedes acceder al asistente desde Calibracion -> Wizard"
 
+# 
+#: ultralcd.cpp:5030
+msgid "Z-correct:"
+msgstr "Correccion-Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Z-sensor nr.    [1]"
+
+# 
+#: ultralcd.cpp:6954
+msgid "Z-probe nr.    [3]"
+msgstr "Z-sensor nr.    [3]"
+
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3024
 msgid "[0;0] point offset"
 msgstr "[0;0] punto offset"

lang/po/new/fr.po

@@ -17,6 +17,11 @@ msgstr "\e[2JLa detection de crash peut etre\e[1;0Hactive seulement\e[2;0Hen mod
 msgid "\e[2JWARNING:\e[1;0HCrash detection\e[2;0Hdisabled in\e[3;0HStealth mode"
 msgstr "\e[2JATTENTION :\e[1;0HDetection de crash\e[2;0H desactivee en\e[3;0Hmode Furtif"
 
+# 
+#: ultralcd.cpp:3913
+msgid "  1"
+msgstr "  1"
+
 # MSG_PLANNER_BUFFER_BYTES
 #: Marlin_main.cpp:1184
 msgid "  PlannerBufferBytes: "
@@ -48,10 +53,15 @@ msgid " of 4"
 msgstr "de 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr "de 9"
 
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr "[off]"
+
 # MSG_FACTOR
 #: ultralcd.cpp:6008
 msgid " \002 Fact"
@@ -68,7 +78,7 @@ msgid " \002 Min"
 msgstr " \002 Min"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2294
 msgid ">Cancel"
 msgstr ">Annuler"
 
@@ -77,33 +87,38 @@ msgstr ">Annuler"
 msgid "Adjusting Z"
 msgstr "Ajustement de Z"
 
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3144
+msgid "Adjusting Z:"
+msgstr "Ajuster Z :"
+
 # MSG_ALL c=19 r=1
 #: messages.c:11
 msgid "All"
 msgstr "Tous"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Tout est correct"
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Tout est pret. Bonne\nimpression !"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1979
 msgid "Ambient"
 msgstr "Ambiant"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2573
 msgid "and press the knob"
 msgstr "et pressez le bouton"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3442
 msgid "Are left and right Z~carriages all up?"
 msgstr "Z~carriages gauche +\ndroite tout en haut?"
 
@@ -133,27 +148,27 @@ msgid "Auto home"
 msgstr "Mise a 0 des axes"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6731
 msgid "AutoLoad filament"
 msgstr "AutoCharge du filament"
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4375
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Chargement auto du\nfilament uniquement\nsi le capteur de\nfilament est active."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2768
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Chargement auto du\nfilament actif,\nappuyez sur le btn\net inserez le fil."
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Axe"
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Longueur de l'axe"
 
@@ -167,13 +182,18 @@ msgstr "Babystepping X"
 msgid "Babystepping Y"
 msgstr "Babystepping Y"
 
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Retour"
+
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Lit"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Lit / Chauffage"
 
@@ -188,7 +208,7 @@ msgid "Bed Heating"
 msgstr "Chauffe du lit"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5663
 msgid "Bed level correct"
 msgstr "Corr. niveau plateau"
 
@@ -213,17 +233,17 @@ msgid "Begin file list"
 msgstr "Debut liste fichiers"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2007
 msgid "Belt status"
 msgstr "Statut courroie"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Coupure detectee.\nRecup. impression ?"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4566
 msgid "Calibrate"
 msgstr "Calibrer"
 
@@ -233,7 +253,7 @@ msgid "Calibrate E"
 msgstr "Calibrer E"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5652
 msgid "Calibrate XYZ"
 msgstr "Calibrer XYZ"
 
@@ -243,12 +263,12 @@ msgid "Calibrate Z"
 msgstr "Calibrer Z"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
 msgstr "Calib. mise a 0"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibration de XYZ.\nTournez le bouton\npour monter le\nchariot de l'axe Z\njusqu'aux butees.\nCliquez une fois\nfait."
 
@@ -258,22 +278,22 @@ msgid "Calibrating Z"
 msgstr "Calibration de Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibration de Z.\nTournez le bouton\npour monter le\nchariot de l'axe Z\njusqu'aux butees.\nCliquez une fois\nfait."
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Calibration"
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:832
 msgid "Calibration done"
 msgstr "Calibration terminee"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Cancel"
 msgstr "Annuler"
 
@@ -293,7 +313,7 @@ msgid "Card inserted"
 msgstr "Carte  inseree"
 
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Carte retiree"
 
@@ -313,12 +333,12 @@ msgid "Change SD card"
 msgstr "Changer carte SD"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2584
 msgid "Change success!"
 msgstr "Changement reussi!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2661
 msgid "Changed correctly?"
 msgstr "Change correctement?"
 
@@ -328,40 +348,45 @@ msgid "Changing filament!"
 msgstr "Changement filament!"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Verification du lit"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Verifications butees"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Verif. tete impr."
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Verif. des capteurs"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Verification axe X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Verification axe Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Verification axe Z"
 
+# 
+#: ultralcd.cpp:5537
+msgid "Checks"
+msgstr "Verifications"
+
 # MSG_ERR_CHECKSUM_MISMATCH
 #: cmdqueue.cpp:444
 msgid "checksum mismatch, Last Line: "
@@ -378,7 +403,7 @@ msgid "Choose filament:"
 msgstr "Choix du filament :"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2673
 msgid "Color not correct"
 msgstr "Couleur incorrecte"
 
@@ -393,12 +418,12 @@ msgid "Copy selected language from XFLASH?"
 msgstr "Copier la langue selectionne depuis la XFLASH ?"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4499
 msgid "Copy selected language?"
 msgstr "Copier la langue\nselectionne ?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Crash"
 msgstr "Crash"
 
@@ -423,22 +448,27 @@ msgid "Crash detected."
 msgstr "Crash detecte."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:618
 msgid "Crash detected. Resume print?"
 msgstr "Crash detecte. Poursuivre l'impression ?"
 
+# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
+#:
+msgid "Crash detection can\nbe turned on only in\nNormal mode"
+msgstr "La detection de\ncrash ne peut etre\nactive en mode\nNormal"
+
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5804
 msgid "Current"
 msgstr "Actuel"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2106
 msgid "Date:"
 msgstr "Date :"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5552
 msgid "Disable steppers"
 msgstr "Desactiver moteurs"
 
@@ -448,7 +478,7 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "La distance entre la\npointe de la buse et\nla surface du\nplateau n'a pas\nencore ete reglee.\nSuivez le manuel,\nchapitre Premiers\npas, section\nCalibration de la\npremiere couche."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4968
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Voulez-vous repeter\nla derniere etape\npour reajuster la\ndistance entre la\nbuse et le plateau\nchauffant ?"
 
@@ -462,13 +492,18 @@ msgstr "Calibration de E\nterminee. Nettoyez\nla buse. Cliquez une\nfois fait."
 msgid "E-correct"
 msgstr "Correct-E"
 
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5032
+msgid "E-correct:"
+msgstr "Correct-E:"
+
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Eject"
 msgstr "Ejecter"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Ejecter le fil."
 
@@ -498,7 +533,7 @@ msgid "Eject filament 5"
 msgstr "Ejecter fil. 5"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1435
 msgid "Ejecting filament"
 msgstr "Ejection filament"
 
@@ -508,17 +543,17 @@ msgid "End file list"
 msgstr "Fin liste fichiers"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Butee"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Butee non atteinte"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Butees"
 
@@ -538,7 +573,7 @@ msgid "enqueing \""
 msgstr "mise en file \""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Erreur - la memoire\nstatique a ete\necrasee"
 
@@ -553,7 +588,7 @@ msgid "ERROR:"
 msgstr "ERREUR :"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4388
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "ERREUR : Le capteur\nde filament ne\nrepond pas, verifiez\nle branchement."
 
@@ -588,17 +623,17 @@ msgid "Extruder 4"
 msgstr "Extrudeur 4"
 
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Ventilo extrudeur:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2137
 msgid "Extruder info"
 msgstr "Infos extrudeur"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5066
 msgid "F. autoload  [on]"
 msgstr "ChargAuto f. [on]"
 
@@ -608,37 +643,42 @@ msgid "F. autoload [N/A]"
 msgstr "AutoCharg F [N/A]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5068
 msgid "F. autoload [off]"
 msgstr "AutoCharg F [off]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr "Statist. d'echec"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
 msgstr "Stat. echecs MMU"
 
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Faux declenchement"
+
 # MSG_FAN_SPEED c=14
 #: messages.c:31
 msgid "Fan speed"
 msgstr "Vitesse ventil"
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventilateur"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5561
 msgid "Fans check   [on]"
 msgstr "Verif ventilo[on]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5563
 msgid "Fans check  [off]"
 msgstr "Verif venti [off]"
 
@@ -653,7 +693,7 @@ msgid "Fil. sensor response is poor, disable it?"
 msgstr "Capteur de fil. non\nprecis, desactiver ?"
 
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5046
 msgid "Fil. sensor [N/A]"
 msgstr "Capteur Fil. [N/A]"
 
@@ -663,7 +703,7 @@ msgid "Fil. sensor [off]"
 msgstr "Capteur Fil.[off]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Filam. runouts"
 msgstr "Fins de filament"
 
@@ -678,12 +718,12 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament extrude et\navec bonne couleur ?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2669
 msgid "Filament not loaded"
 msgstr "Filament non charge"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Capteur de filament"
 
@@ -693,7 +733,7 @@ msgid "Filament sensor:"
 msgstr "Capteur filament :"
 
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2838
 msgid "Filament used"
 msgstr "Filament utilise"
 
@@ -703,7 +743,7 @@ msgid "Filament used:  "
 msgstr "Filament utilise :"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Fichier incomplet.\nContinuer qd meme ?"
 
@@ -717,53 +757,93 @@ msgstr "Fichier ouvert :"
 msgid "File selected"
 msgstr "Fichier selectionne"
 
+# 
+#: ultralcd.cpp:3943
+msgid "FINDA:"
+msgstr "FINDA :"
+
 # MSG_FINISHING_MOVEMENTS c=20 r=1
 #: messages.c:40
 msgid "Finishing movements"
 msgstr "Mouvements de fin"
 
+# 
+#: ultralcd.cpp:5443
+msgid "Firmware   [none]"
+msgstr "Firmware [aucune]"
+
+# 
+#: ultralcd.cpp:5446
+msgid "Firmware   [warn]"
+msgstr "Firmware  [avert]"
+
+# 
+#: ultralcd.cpp:5449
+msgid "Firmware [strict]"
+msgstr "Firmware[stricte]"
+
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Cal. 1ere couche"
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4880
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "D'abord, je vais\nlancer le Selftest\npour verifier les\nproblemes\nd'assemblage les\nplus communs."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Corrigez le probleme et appuyez sur le bouton de l'unite MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Flux"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2099
 msgid "forum.prusa3d.com"
 msgstr "forum.prusa3d.com"
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Ventilo impr avant ?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3217
 msgid "Front side[um]"
 msgstr "Avant [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Ventilos avt/gauche"
 
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr "Le G-code a ete prepare pour une autre version de l'imprimante. Continuer?"
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr "Le G-code a ete prepare pour une autre version de l'imprimante. Veuillez decouper le modele a nouveau. L'impression a ete annulee. "
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr "Le G-code a ete prepare pour une version plus recente du firmware. Continuer?"
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr "Le G-code a ete prepare pour une version plus recente du firmware. Veuillez mettre a jour le firmware. L'impression  annulee."
+
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Chauffage/Thermistor"
 
@@ -773,7 +853,7 @@ msgid "Heating"
 msgstr "Chauffe"
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8411
 msgid "Heating disabled by safety timer."
 msgstr "Chauffe desactivee\npar le compteur de\nsecurite."
 
@@ -783,27 +863,32 @@ msgid "Heating done."
 msgstr "Chauffe terminee."
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4859
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Bonjour, je suis\nvotre imprimante\nOriginal Prusa i3.\nVoulez-vous que je\nvous guide a travers\nle processus\nd'installation ?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2100
 msgid "howto.prusa3d.com"
 msgstr "howto.prusa3d.com"
 
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "Config HW"
+
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4889
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Je vais maintenant\nlancer la\ncalibration xyz.\nCela prendra 12 min\nenviron."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4897
 msgid "I will run z calibration now."
 msgstr "Je vais maintenant\nlancer la\ncalibration z."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4962
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Je vais commencer a \nimprimer une ligne\net vous baisserez au\nfur et a mesure la\nbuse en tournant le\nbouton jusqu'a\natteindre la hauteur\noptimale. Regardez\nles photos dans\nnotre manuel au\nchapitre Calibration"
 
@@ -813,7 +898,7 @@ msgid "Improving bed calibration point"
 msgstr "Amelioration du point de calibration du lit"
 
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Ecran d'info"
 
@@ -823,7 +908,7 @@ msgid "Init. SD card"
 msgstr "Init. carte SD"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2569
 msgid "Insert filament"
 msgstr "Inserez le filament"
 
@@ -848,27 +933,32 @@ msgid "Insert filament into extruder 4. Click when done."
 msgstr "Inserez le filament\ndans l'extrudeur 4.\nCliquez une fois\npret."
 
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:3947
+msgid "IR:"
+msgstr "IR :"
+
+# 
+#: ultralcd.cpp:4922
 msgid "Is filament 1 loaded?"
 msgstr "Le filament 1 est-il charge ?"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4925
 msgid "Is filament loaded?"
 msgstr "Le filament est-il\ncharge ?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4956
 msgid "Is it PLA filament?"
 msgstr "Est-ce du filament\nPLA ?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4701
 msgid "Is PLA filament loaded?"
 msgstr "Le filament PLA\nest-il charge ?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "Feuille d'acier sur\nplateau chauffant ?"
 
@@ -883,27 +973,27 @@ msgid "KILLED. "
 msgstr "TUE."
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1828
 msgid "Last print"
 msgstr "Derniere impression"
 
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1845
 msgid "Last print failures"
 msgstr "Echecs derniere impr"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2967
 msgid "Left"
 msgstr "Gauche"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Ventilo tete gauche?"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3215
 msgid "Left side [um]"
 msgstr "Gauche [um]"
 
@@ -913,7 +1003,7 @@ msgid "Left:"
 msgstr "Gauche :"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5575
 msgid "Lin. correction"
 msgstr "Correction lin."
 
@@ -923,7 +1013,7 @@ msgid "Live adjust Z"
 msgstr "Ajuster Z en direct"
 
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6059
 msgid "Load all"
 msgstr "Tout charger"
 
@@ -958,12 +1048,12 @@ msgid "Load filament 5"
 msgstr "Charger fil. 5"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6714
 msgid "Load to nozzle"
 msgstr "Charger dans la buse"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2609
 msgid "Loading color"
 msgstr "Chargement couleur"
 
@@ -973,7 +1063,7 @@ msgid "Loading filament"
 msgstr "Chargement filament"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Poulie lache"
 
@@ -993,7 +1083,7 @@ msgid "M109 Invalid extruder "
 msgstr "M109 extrudeur invalide"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Cal. 1ere couche"
 
@@ -1012,8 +1102,23 @@ msgstr "M218 extrudeur invalide"
 msgid "M221 Invalid extruder "
 msgstr "M221 extrudeur invalide"
 
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Comp. aimants [On]"
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Comp. aimants[N/A]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Comp. aimants[Off]"
+
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Principal"
 
@@ -1023,7 +1128,7 @@ msgid "Mark filament 100mm from extruder body. Click when done."
 msgstr "Marquez le filament\na 100 mm du corps de\nl'extrudeur. Cliquez\nune fois fait."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3002
 msgid "Measured skew"
 msgstr "Deviation mesuree"
 
@@ -1033,32 +1138,67 @@ msgid "Measured skew:"
 msgstr "Ecart mesure :"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Mesure de la hauteur de reference du point de calibration"
 
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Mesh         [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Mesh         [7x7]"
+
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5658
 msgid "Mesh Bed Leveling"
 msgstr "Mesh Bed Leveling"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:5572
+msgid "Mesh bed leveling"
+msgstr "Mesh bed leveling"
+
+# 
+#: Marlin_main.cpp:881
+msgid "MK3 firmware detected on MK3S printer"
+msgstr "Firmware MK3 detecte sur imprimante MK3S"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr "Firmware MK3S detecte sur imprimante MK3"
+
+# 
+#: ultralcd.cpp:1845
 msgid "MMU fails"
 msgstr "Echec MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1617
 msgid "MMU load failed     "
 msgstr "Echec chargement MMU"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1845
 msgid "MMU load fails"
 msgstr "Echecs charg. MMU"
 
 # 
-#: mmu.cpp:635
+#: ultralcd.cpp:5204
+msgid "MMU Mode [Normal]"
+msgstr "Mode MMU [Normal]"
+
+# 
+#: ultralcd.cpp:5205
+msgid "MMU Mode[Stealth]"
+msgstr "Mode MMU [Furtif]"
+
+# 
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "Le MMU necessite l'attention de l'utilisateur."
 
@@ -1068,82 +1208,102 @@ msgid "MMU needs user attention. Fix the issue and then press button on MMU unit
 msgstr "La MMU requiert votre attention. Réglez le problème puis appuyez sur le bouton on sur l'unité MMU."
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Reprise de la position ..."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Remontee en\ntemperature..."
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Reprise ..."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "MMU power fails"
 msgstr "Echecs alim. MMU"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2112
 msgid "MMU2 connected"
 msgstr "MMU2 connecte"
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Mode     [Normal]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Mode [silencieux]"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Mode [Furtif]"
 
+# 
+#: ultralcd.cpp:4424
+msgid "Mode change in progress ..."
+msgstr "Changement de mode en cours..."
+
 # MSG_AUTO_MODE_ON
 #: messages.c:12
 msgid "Mode [auto power]"
 msgstr "Mode [puiss.auto]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Mode [haute puiss]"
 
+# 
+#: ultralcd.cpp:5404
+msgid "Model      [none]"
+msgstr "Modele   [aucune]"
+
+# 
+#: ultralcd.cpp:5407
+msgid "Model      [warn]"
+msgstr "Modele    [avert]"
+
+# 
+#: ultralcd.cpp:5410
+msgid "Model    [strict]"
+msgstr "Modele  [stricte]"
+
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Moteur"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5550
 msgid "Move axis"
 msgstr "Deplacer l'axe"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4291
 msgid "Move X"
 msgstr "Deplacer X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4292
 msgid "Move Y"
 msgstr "Deplacer Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4293
 msgid "Move Z"
 msgstr "Deplacer Z"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2973
 msgid "N/A"
 msgstr "N/A"
 
@@ -1153,7 +1313,7 @@ msgid "New firmware version available:"
 msgstr "Nouvelle version de\nfirmware disponible:"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Non"
 
@@ -1168,12 +1328,12 @@ msgid "No Checksum with line number, Last Line: "
 msgstr "Pas de checksum avec\nnumero de ligne, \nDerniere ligne :"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5254
 msgid "No move."
 msgstr "Pas de mouvement."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6694
 msgid "No SD card"
 msgstr "Pas de carte SD"
 
@@ -1183,37 +1343,67 @@ msgid "No thermistors - no temperature"
 msgstr "Pas de thermistors\n- pas de temperature"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Non connecte"
 
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Ne tourne pas"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4961
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Maintenant je vais\ncalibrer la distance \nentre la pointe de\nla buse et la\nsurface du plateau\nchauffant."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4905
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Maintenant je vais\nprechauffer la buse\npour du PLA."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4896
 msgid "Now remove the test print from steel sheet."
 msgstr "Retirez maintenant l'impression de test de la feuille d'acier."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Buse"
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:5319
+msgid "Nozzle     [none]"
+msgstr "Buse     [aucune]"
+
+# 
+#: ultralcd.cpp:5322
+msgid "Nozzle     [warn]"
+msgstr "Buse      [avert]"
+
+# 
+#: ultralcd.cpp:5325
+msgid "Nozzle   [strict]"
+msgstr "Buse    [stricte]"
+
+# 
+#: ultralcd.cpp:5365
+msgid "Nozzle d.  [0.25]"
+msgstr "Diam. buse [0.25]"
+
+# 
+#: ultralcd.cpp:5368
+msgid "Nozzle d.  [0.40]"
+msgstr "Diam. buse [0.40]"
+
+# 
+#: ultralcd.cpp:5371
+msgid "Nozzle d.  [0.60]"
+msgstr "Diam. buse [0.60]"
+
+# 
+#: ultralcd.cpp:1787
 msgid "Nozzle FAN"
 msgstr "Ventilateur buse"
 
@@ -1238,7 +1428,7 @@ msgid "ok"
 msgstr "ok"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1535
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Anciens reglages\ntrouves. Le PID, les\nEsteps etc. par\ndefaut seront regles"
 
@@ -1258,7 +1448,7 @@ msgid "openRoot failed"
 msgstr "Echec openRoot"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6657
 msgid "Pause print"
 msgstr "Pause de l'impr."
 
@@ -1268,42 +1458,47 @@ msgid "Pick print"
 msgstr "Choisir impression"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1613
 msgid "PID cal.           "
 msgstr "Calib. PID"
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1619
 msgid "PID cal. finished"
 msgstr "Calib. PID terminee"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5664
 msgid "PID calibration"
 msgstr "Calibration PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:862
 msgid "PINDA Heating"
 msgstr "Chauffe de la PINDA"
 
+# 
+#: ultralcd.cpp:3939
+msgid "PINDA:"
+msgstr "PINDA :"
+
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Placez une feuille\nde papier sous la\nbuse pendant la\ncalibration des 4\npremiers points.\nSi la buse accroche\nle papier, eteignez\nvite l'imprimante."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Verifiez :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Merci de verifier\nnotre manuel et de\ncorriger le\nprobleme. Poursuivez\nalors l'assistant en\nredemarrant\nl'imprimante."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4970
 msgid "Please clean heatbed and then press the knob."
 msgstr "Nettoyez le plateau\nchauffant et appuyez\nsur le bouton."
 
@@ -1313,12 +1508,12 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Nettoyez la buse\npour la calibration.\nCliquez une fois\nfait."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4804
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Inserez du filament\nPLA dans l'extrudeur\npuis appuyez sur le\nbouton pour le\ncharger."
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4800
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Veuillez inserer du filament PLA dans le premier tube du MMU, et pressez sur le bouton pour le charger."
 
@@ -1328,52 +1523,52 @@ msgid "Please load PLA filament and then resume Wizard by rebooting the printer.
 msgstr "Chargez le filament\nPLA et poursuivez\nl'assistant en\nredemarrant\nl'imprimante."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4706
 msgid "Please load PLA filament first."
 msgstr "Chargez d'abord le\nfilament PLA."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3083
 msgid "Please open idler and remove filament manually."
 msgstr "Ouvrez l'idler et\nretirez le filament\nmanuellement."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Placez la feuille\nd'acier sur le\nplateau chauffant."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Appuyez sur le\nbouton pour \ndecharger le \nfilament"
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Retirez\nimmediatement le\nfilament"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1441
 msgid "Please remove filament and then press the knob."
 msgstr "Veuillez retirer le filament puis appuyez sur le bouton."
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4895
 msgid "Please remove shipping helpers first."
 msgstr "Veuillez retirer d'abord les protections d'envoi."
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Retirez la feuille\nd'acier du plateau\nchauffant."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4317
 msgid "Please run XYZ calibration first."
 msgstr "Veuillez d'abord lancer la calibration XYZ."
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1360
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Veuillez mettre a\njour le firmware de\nvotre MMU2. En\nattente d'un reset."
 
@@ -1383,12 +1578,12 @@ msgid "Please upgrade."
 msgstr "Mettez a jour le FW."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Merci de patienter"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Power failures"
 msgstr "Coupures de courant"
 
@@ -1398,27 +1593,37 @@ msgid "PowerUp"
 msgstr "Demarrage"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6644
 msgid "Preheat"
 msgstr "Prechauffage"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Prechauffez la buse!"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Prechauffage de la\nbuse. Merci de\npatienter."
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2290
+msgid "Preheating to cut"
+msgstr "Prechauffage pour couper"
+
+# 
+#: ultralcd.cpp:2287
+msgid "Preheating to eject"
+msgstr "Prechauffage pour ejecter"
+
+# 
+#: ultralcd.cpp:2280
 msgid "Preheating to load"
 msgstr "Chauffe pour charger"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2284
 msgid "Preheating to unload"
 msgstr "Chauffe pr decharger"
 
@@ -1428,27 +1633,27 @@ msgid "Prepare new filament"
 msgstr "Preparez le filament"
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10312
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Appuyez sur le\nbouton pour\nprechauffer la buse\net continuer."
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2210
 msgid "Press the knob"
 msgstr "App. sur sur bouton"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Appuyez sur le bouton pour poursuivre la mise en temperature de la buse."
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Impression annulee"
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1789
 msgid "Print FAN"
 msgstr "Ventilo impression"
 
@@ -1458,7 +1663,7 @@ msgid "Print FAN: "
 msgstr "Vent impr :"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Ventilo impr. :"
 
@@ -1468,12 +1673,12 @@ msgid "Print from SD"
 msgstr "Impr depuis la SD"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1080
 msgid "Print paused"
 msgstr "Impression en pause"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2838
 msgid "Print time"
 msgstr "Temps d'impression"
 
@@ -1487,6 +1692,26 @@ msgstr "Temps d'impression :"
 msgid "Printer disconnected"
 msgstr "Impri. deconnectee"
 
+# 
+#: util.cpp:473
+msgid "Printer FW version differs from the G-code. Continue?"
+msgstr "Version FW de l'imprimante differente du G-Code. Continuer ?"
+
+# 
+#: util.cpp:480
+msgid "Printer FW version differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Version FW de l'imprimante differente du G-Code. Merci de verifier le parametre dans les reglages. Impression annulee."
+
+# 
+#: util.cpp:506
+msgid "Printer G-code level differs from the G-code. Continue?"
+msgstr "Niveau de G-Code de l'imprimante different du G-Code. Continuer ?"
+
+# 
+#: util.cpp:513
+msgid "Printer G-code level differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Merci de verifier le parametre dans les reglages. Impression annulee."
+
 # MSG_ERR_KILLED
 #: Marlin_main.cpp:7547
 msgid "Printer halted. kill() called!"
@@ -1497,6 +1722,26 @@ msgstr "Imprimante stoppee.\nkill() appelee !"
 msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
 msgstr "L'imprimante n'a pas\nencore ete calibree.\nSuivez le manuel,\nchapitre Premiers\npas, section\nProcessus de\ncalibration."
 
+# 
+#: util.cpp:423
+msgid "Printer model differs from the G-code. Continue?"
+msgstr "Modele d'imprimante different du G-Code. Continuer ?"
+
+# 
+#: util.cpp:430
+msgid "Printer model differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Modele d'imprimante diffent du G-Code. Merci de verifier le parametre dans les reglages. Impression annulee."
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Diametre de la  buse de l'imprimante different du G-Code. Continuer ?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Diametre de la  buse de l'imprimante different du G-Code. Merci de verifier le parametre dans les reglages. Impression annulee."
+
 # MSG_ERR_STOPPED
 #: messages.c:32
 msgid "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
@@ -1512,6 +1757,11 @@ msgstr "Prusa i3 MK2 prete."
 msgid "Prusa i3 MK2.5 ready."
 msgstr "Prusa i3 MK2.5 prete."
 
+# 
+#:
+msgid "Prusa i3 MK3 OK."
+msgstr "Prusa i3 MK3 OK."
+
 # WELCOME_MSG c=20
 #:
 msgid "Prusa i3 MK3 ready."
@@ -1523,17 +1773,17 @@ msgid "Prusa i3 MK3S OK."
 msgstr "Prusa i3 MK3S OK."
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2098
 msgid "prusa3d.com"
 msgstr "prusa3d.com"
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3218
 msgid "Rear side [um]"
 msgstr "Arriere [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9712
 msgid "Recovering print    "
 msgstr "Recup. impression"
 
@@ -1543,10 +1793,15 @@ msgid "Refresh"
 msgstr "Rafraichir"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Retirez l'ancien filament puis appuyez sur le bouton pour charger le nouveau."
 
+# 
+#: ultralcd.cpp:6605
+msgid "Rename"
+msgstr "Renommer"
+
 # MSG_M119_REPORT
 #: Marlin_main.cpp:5297
 msgid "Reporting endstop status"
@@ -1563,32 +1818,32 @@ msgid "Resend: "
 msgstr "Renvoi :"
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3219
 msgid "Reset"
 msgstr "Reinitialiser"
 
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5669
 msgid "Reset XYZ calibr."
 msgstr "Reinit. calibr. XYZ"
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6664
 msgid "Resume print"
 msgstr "Reprendre impression"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Reprise de l'impr."
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2968
 msgid "Right"
 msgstr "Droite"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3216
 msgid "Right side[um]"
 msgstr "Droite [um]"
 
@@ -1603,22 +1858,22 @@ msgid "Rotate knob until mark reaches extruder body. Click when done."
 msgstr "Tournez le bouton\njusqu'a ce que la\nmarque atteigne le\ncorps de\nl'extrudeur. Cliquez\nune fois fait."
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5587
 msgid "RPi port     [on]"
 msgstr "Port RPi [on]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5585
 msgid "RPi port    [off]"
 msgstr "Port RPi [off]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4723
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Lancer l'Assistant\nsupprimera les\nresultats actuels de\ncalibration et\ncommencera du debut.\nContinuer ?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5220
 msgid "SD card  [normal]"
 msgstr "Carte SD [normal]"
 
@@ -1633,7 +1888,7 @@ msgid "SD card [FlshAir]"
 msgstr "Carte SD [FlashAir]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5218
 msgid "SD card [flshAir]"
 msgstr "Carte SD [flashAir]"
 
@@ -1652,53 +1907,63 @@ msgstr "Octet d'impression de la SD"
 msgid "Searching bed calibration point"
 msgstr "Recherche du point de calibration du lit"
 
+# 
+#: ultralcd.cpp:6601
+msgid "Select"
+msgstr "Selectionner"
+
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5594
 msgid "Select language"
 msgstr "Choisir langue"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4943
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Selectionnez la temperature de prechauffage de la buse qui correspond a votre materiau."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Select PLA filament:"
 msgstr "Selectionnez le filament PLA :"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Auto-test OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Debut auto-test"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5645
 msgid "Selftest         "
 msgstr "Auto-test"
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Erreur auto-test !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Echec de l'auto-test"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1567
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Le Selftest sera\nlance pour calibrer\nla remise a zero\nprecise sans capteur"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:2138
+msgid "Sensor info"
+msgstr "Info capteur"
+
+# 
+#: ultralcd.cpp:3938
 msgid "Sensor state"
 msgstr "Etat capteur"
 
@@ -1708,17 +1973,17 @@ msgid "Sensors info"
 msgstr "Infos capteurs"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3227
 msgid "Set temperature:"
 msgstr "Regler temp. :"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Reglages"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3005
 msgid "Severe skew"
 msgstr "Deviation severe"
 
@@ -1727,8 +1992,13 @@ msgstr "Deviation severe"
 msgid "Severe skew:"
 msgstr "Ecart severe :"
 
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Feuille"
+
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5666
 msgid "Show end stops"
 msgstr "Afficher butees"
 
@@ -1743,7 +2013,7 @@ msgid "Sleep..."
 msgstr "Repos..."
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3004
 msgid "Slight skew"
 msgstr "Deviation legere"
 
@@ -1753,15 +2023,30 @@ msgid "Slight skew:"
 msgstr "Leger ecart :"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Certains fichiers ne\nseront pas tries.\nMax 100 fichiers\ntries par dossier."
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4833
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Problemes rencontres, nivellement de l'axe Z applique..."
 
+# MSG_SORT_NONE c=17 r=1
+#: ultralcd.cpp:5230
+msgid "Sort       [none]"
+msgstr "Tri       [aucun]"
+
+# MSG_SORT_TIME c=17 r=1
+#: ultralcd.cpp:5228
+msgid "Sort       [time]"
+msgstr "Tri        [date]"
+
+# MSG_SORT_ALPHA c=17 r=1
+#: ultralcd.cpp:5229
+msgid "Sort   [alphabet]"
+msgstr "Tri    [alphabet]"
+
 # MSG_SORT_NONE c=17 r=1
 #: ultralcd.cpp:4250
 msgid "Sort:      [None]"
@@ -1803,117 +2088,132 @@ msgid "Sort:  [time]"
 msgstr "Tri : [heure]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Tri des fichiers"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Son [fort]"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#:
 msgid "Sound      [mute]"
 msgstr "Son [muet]"
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Son [une fois]"
 
+# 
+#:
+msgid "Sound     [assist]"
+msgstr "Son [Assist]"
+
+# 
+#: sound.h:9
+msgid "Sound     [blind]"
+msgstr "Son     [aveugle]"
+
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Son [silencieux]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Vitesse"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Tourne"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5098
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin    [on]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5094
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin   [N/A]"
 
 # MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+#: ultralcd.cpp:5102
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [off]"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4330
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Une temperature\nambiante stable de\n21-26C et un support\nstable sont requis."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistiques"
 
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr "Plaques en acier"
+
 # MSG_STEPPER_TOO_HIGH
 #: stepper.cpp:345
 msgid "Steprate too high: "
 msgstr "Nombre de pas trop eleve :"
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Arreter impression"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ARRETE."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Support"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Echange"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Calib. Temp."
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5581
 msgid "Temp. cal.   [on]"
 msgstr "Calib. Temp. [on]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5579
 msgid "Temp. cal.  [off]"
 msgstr "Calib. Temp.[off]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5675
 msgid "Temp. calibration"
 msgstr "Calibration temp."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5548
 msgid "Temperature"
 msgstr "Temperature"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3864
 msgid "Temperature calibration failed"
 msgstr "Echec de la\ncalibration en\ntemperature"
 
@@ -1923,12 +2223,12 @@ msgid "Temperature calibration has not been run yet"
 msgstr "La calibration en\ntemperature n'a pas\nencore ete lancee"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "La calibration en\ntemperature est\nterminee et activee.\nLa calibration en\ntemperature peut\netre desactivee dans\nle menu Reglages->\nCal. Temp."
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2144
 msgid "Temperatures"
 msgstr "Temperatures"
 
@@ -1938,27 +2238,27 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Il y a encore besoin d'effectuer la calibration Z. Veuillez suivre le manuel, chapitre Premiers pas, section Processus de calibration."
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2217
 msgid "to load filament"
 msgstr "pour charger le fil."
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2221
 msgid "to unload filament"
 msgstr "pour decharger fil."
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1829
 msgid "Total"
 msgstr "Total"
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "Total failures"
 msgstr "Total des echecs"
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2860
 msgid "Total filament"
 msgstr "Filament total"
 
@@ -1968,7 +2268,7 @@ msgid "Total filament :"
 msgstr "Total filament :"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2860
 msgid "Total print time"
 msgstr "Temps total impr."
 
@@ -1983,17 +2283,17 @@ msgid "TRIGGERED"
 msgstr "ACTIVE"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6641
 msgid "Tune"
 msgstr "Regler"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2120
 msgid "unknown"
 msgstr "inconnu"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Unload"
 msgstr "Decharger"
 
@@ -2003,7 +2303,7 @@ msgid "Unload all"
 msgstr "Decharger tout"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Decharger fil."
 
@@ -2028,22 +2328,22 @@ msgid "Unload filament 4"
 msgstr "Decharger fil. 4"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Dechargement fil."
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4779
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Utilisez decharger pour retirer le filament 1 s'il depasse du  tube arriere du MMU. Utilisez ejecter s'il est cache dans le tube."
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5803
 msgid "Used during print"
 msgstr "Utilise pdt impr."
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2147
 msgid "Voltages"
 msgstr "Tensions"
 
@@ -2053,32 +2353,37 @@ msgid "volume.init failed"
 msgstr "Echec volume.init"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5225
 msgid "Wait for user..."
 msgstr "Attente utilisateur..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3371
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Attente du\nrefroidissement des\nbuse et plateau"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3335
 msgid "Waiting for PINDA probe cooling"
 msgstr "Attente du\nrefroidissement de\nla sonde PINDA"
 
+# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
+#:
+msgid "WARNING:\nCrash detection\ndisabled in\nStealth mode"
+msgstr "ATTENTION :\nDetection de crash\ndesactivee en mode\nFurtif"
+
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1527
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Attention : Types\nd'imprimante et de\ncarte mere modifies"
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1519
 msgid "Warning: motherboard type changed."
 msgstr "Attention : Type de\ncarte mere modifie."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1523
 msgid "Warning: printer type changed."
 msgstr "Attention : Type\nd'imprimante modifie"
 
@@ -2088,17 +2393,17 @@ msgid "WARNING: This is an unofficial, unsupported build. Use at your own risk!"
 msgstr "ATTENTION : ceci est\nune build non\nofficielle et non\nsupportee. Utilisez\nla a votre propre\nrisque !"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3072
 msgid "Was filament unload successful?"
 msgstr "Dechargement du\nfilament reussi ?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Erreur de cablage"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5642
 msgid "Wizard"
 msgstr "Assistant"
 
@@ -2117,23 +2422,28 @@ msgstr "Ecriture dans le fichier :"
 msgid "X-correct"
 msgstr "Correction-X"
 
+# 
+#: ultralcd.cpp:5028
+msgid "X-correct:"
+msgstr "Correct-X:"
+
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2136
 msgid "XYZ cal. details"
 msgstr "Details calib. XYZ"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Calibration XYZ OK.\nL'ecart sera corrige\nautomatiquement."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3832
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Calibration XYZ OK.\nLes axes X/Y sont\nlegerement non\nperpendiculaires.\nBon boulot !"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3813
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Calibration XYZ\ncompromise. Les\npoints de\ncalibration avant ne\nsont pas\natteignables."
 
@@ -2143,17 +2453,17 @@ msgid "XYZ calibration compromised. Left front calibration point not reachable."
 msgstr "Calibration XYZ\ncompromise. Le point\n de calibration\n avant gauche n'est\n pas atteignable."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Calibration XYZ\ncompromise. Le point\nde calibration avant\ndroit n'est pas\natteignable."
 
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3795
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Echec calibration\nXYZ. Le point de\ncalibration du\nplateau n'a pas ete\ntrouve."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3801
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Echec calibration\nXYZ. Les points de\ncalibration avant ne\nsont pas\natteignables."
 
@@ -2168,17 +2478,17 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Echec calibration\nXYZ. Consultez le\nmanuel."
 
 # 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Echec calibration\nXYZ. Le point de\ncalibration avant\ndroit n'est pas\natteignable."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3829
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Calibration XYZ OK.\nLes axes X/Y sont\nperpendiculaires.\nFelicitations !"
 
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2965
 msgid "Y distance from min"
 msgstr "Distance Y du min"
 
@@ -2192,8 +2502,13 @@ msgstr "Distance Y du mini :"
 msgid "Y-correct"
 msgstr "Correction-Y"
 
+# 
+#: ultralcd.cpp:5029
+msgid "Y-correct:"
+msgstr "Correct-Y:"
+
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Oui"
 
@@ -2208,11 +2523,26 @@ msgid "You are using firmware beta version. This is development version. Using t
 msgstr "Vous utilisez un\nfirmware en version\nbeta. C'est une\nversion de dev.\nCeci n'est pas\nrecommande et peut\nendommager\nl'imprimante."
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Vous pouvez toujours\nrelancer l'assistant\ndans Calibration->\nAssistant."
 
+# 
+#: ultralcd.cpp:5030
+msgid "Z-correct:"
+msgstr "Correct-Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Sonde-Z num.   [1]"
+
+# 
+#: ultralcd.cpp:6954
+msgid "Z-probe nr.    [3]"
+msgstr "Sonde-Z num.   [3]"
+
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3024
 msgid "[0;0] point offset"
 msgstr "Offset point [0;0]"

lang/po/new/it.po

@@ -17,6 +17,11 @@ msgstr "\e[2JRilev. impatto\e[1;0Hattivabile solo\e[2;0Hin Modalita normale"
 msgid "\e[2JWARNING:\e[1;0HCrash detection\e[2;0Hdisabled in\e[3;0HStealth mode"
 msgstr "\e[2JATTENZIONE:\e[1;0HRilev. impatto\e[2;0Hdisattivato in\e[3;0HModalita silenziosa"
 
+# 
+#: ultralcd.cpp:3913
+msgid "  1"
+msgstr "  1"
+
 # MSG_PLANNER_BUFFER_BYTES
 #: Marlin_main.cpp:1184
 msgid "  PlannerBufferBytes: "
@@ -48,10 +53,15 @@ msgid " of 4"
 msgstr " su 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr "su 9"
 
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr " [off]"
+
 # MSG_FACTOR
 #: ultralcd.cpp:6008
 msgid " \002 Fact"
@@ -68,7 +78,7 @@ msgid " \002 Min"
 msgstr " \002 Min"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2294
 msgid ">Cancel"
 msgstr ">Annulla"
 
@@ -77,33 +87,38 @@ msgstr ">Annulla"
 msgid "Adjusting Z"
 msgstr "Compensazione Z"
 
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3144
+msgid "Adjusting Z:"
+msgstr "Compensazione Z:"
+
 # MSG_ALL c=19 r=1
 #: messages.c:11
 msgid "All"
 msgstr "Tutti"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Nessun errore"
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Tutto fatto. Buona stampa!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1979
 msgid "Ambient"
 msgstr "Ambiente"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2573
 msgid "and press the knob"
 msgstr "e cliccare manopola"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3442
 msgid "Are left and right Z~carriages all up?"
 msgstr "I carrelli Z sin/des sono altezza max?"
 
@@ -133,27 +148,27 @@ msgid "Auto home"
 msgstr "Trova origine"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6731
 msgid "AutoLoad filament"
 msgstr "Autocaric. filam."
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4375
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Caricamento auto. filam. disp. solo con il sensore attivo..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2768
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Il caricamento automatico e attivo, premete la manopola e inserite il filamento..."
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Assi"
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Lunghezza dell'asse"
 
@@ -167,13 +182,18 @@ msgstr "Babystepping X"
 msgid "Babystepping Y"
 msgstr "Babystepping Y"
 
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Indietro"
+
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Letto"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Letto/Riscald."
 
@@ -188,7 +208,7 @@ msgid "Bed Heating"
 msgstr "Riscald. letto"
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5663
 msgid "Bed level correct"
 msgstr "Correz. liv.letto"
 
@@ -213,17 +233,17 @@ msgid "Begin file list"
 msgstr "Inizio lista file"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2007
 msgid "Belt status"
 msgstr "Stato delle cinghie"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "C'e stato un Blackout. Recuperare la stampa?"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4566
 msgid "Calibrate"
 msgstr "Calibra"
 
@@ -233,7 +253,7 @@ msgid "Calibrate E"
 msgstr "Calibra E"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5652
 msgid "Calibrate XYZ"
 msgstr "Calibra XYZ"
 
@@ -243,12 +263,12 @@ msgid "Calibrate Z"
 msgstr "Calibra Z"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
 msgstr "Calibrazione Home"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrazione XYZ. Ruotare la manopola per alzare il carrello Z fino all'altezza massima. Click per terminare."
 
@@ -258,22 +278,22 @@ msgid "Calibrating Z"
 msgstr "Calibrando Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Calibrazione Z. Ruotare la manopola per alzare il carrello Z fino all'altezza massima. Click per terminare."
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Calibrazione"
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:832
 msgid "Calibration done"
 msgstr "Calibrazione completa"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Cancel"
 msgstr "Annulla"
 
@@ -293,7 +313,7 @@ msgid "Card inserted"
 msgstr "SD inserita"
 
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "SD rimossa"
 
@@ -313,12 +333,12 @@ msgid "Change SD card"
 msgstr "Cambia memoria SD"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2584
 msgid "Change success!"
 msgstr "Cambio riuscito!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2661
 msgid "Changed correctly?"
 msgstr "Cambiato correttamente?"
 
@@ -328,40 +348,45 @@ msgid "Changing filament!"
 msgstr "Cambiando filam."
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Verifica piano"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Verifica finecorsa"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Verifica ugello"
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Controllo sensori"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Verifica asse X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Verifica asse Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Verifica asse Z"
 
+# 
+#: ultralcd.cpp:5537
+msgid "Checks"
+msgstr "Controlli"
+
 # MSG_ERR_CHECKSUM_MISMATCH
 #: cmdqueue.cpp:444
 msgid "checksum mismatch, Last Line: "
@@ -378,7 +403,7 @@ msgid "Choose filament:"
 msgstr "Scegliere filamento:"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2673
 msgid "Color not correct"
 msgstr "Colore non puro"
 
@@ -393,12 +418,12 @@ msgid "Copy selected language from XFLASH?"
 msgstr "Copiare la lingua selezionata da XFLASH?"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4499
 msgid "Copy selected language?"
 msgstr "Copiare la lingua selezionata?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Crash"
 msgstr "Impatto"
 
@@ -423,22 +448,27 @@ msgid "Crash detected."
 msgstr "Rilevato impatto."
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:618
 msgid "Crash detected. Resume print?"
 msgstr "Scontro rilevato. Riprendere la stampa?"
 
+# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
+#:
+msgid "Crash detection can\nbe turned on only in\nNormal mode"
+msgstr "Rilevamento impatto può\nessere attivato in\nModalità Normale"
+
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5804
 msgid "Current"
 msgstr "Attuale"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2106
 msgid "Date:"
 msgstr "Data:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5552
 msgid "Disable steppers"
 msgstr "Disabilita motori"
 
@@ -448,7 +478,7 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Distanza tra la punta dell'ugello e la superficie del letto non ancora imposta. Si prega di seguire il manuale, capitolo Primi Passi, sezione Calibrazione primo layer."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4968
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Desideri ripetere l'ultimo passaggio per migliorare la distanza fra ugello e piatto?"
 
@@ -462,13 +492,18 @@ msgstr "Calibrazione E terminata. Si prega di pulire l'ugello. Click per continu
 msgid "E-correct"
 msgstr "Correzione-E"
 
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5032
+msgid "E-correct:"
+msgstr "Correzione-E:"
+
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Eject"
 msgstr "Espellere"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Espelli filamento "
 
@@ -498,7 +533,7 @@ msgid "Eject filament 5"
 msgstr "Espelli filamento 5"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1435
 msgid "Ejecting filament"
 msgstr "Espellendo filamento "
 
@@ -508,17 +543,17 @@ msgid "End file list"
 msgstr "Fine lista file"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Finecorsa"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Finecorsa fuori portata"
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Finecorsa"
 
@@ -538,7 +573,7 @@ msgid "enqueing \""
 msgstr "accodamento\""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Errore - la memoria statica e stata sovrascritta"
 
@@ -553,7 +588,7 @@ msgid "ERROR:"
 msgstr "ERRORE:"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4388
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "ERRORE: il sensore filam. non risponde,Controllare conness."
 
@@ -588,17 +623,17 @@ msgid "Extruder 4"
 msgstr "Estrusore 4"
 
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Ventola estrusore:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2137
 msgid "Extruder info"
 msgstr "Info estrusore"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5066
 msgid "F. autoload  [on]"
 msgstr "Autocar.filam[on]"
 
@@ -608,37 +643,42 @@ msgid "F. autoload [N/A]"
 msgstr "Autocar.fil.[N/A]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5068
 msgid "F. autoload [off]"
 msgstr "Autocar.fil.[off]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr "Statistiche fallimenti"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
 msgstr "Statistiche fallimenti MMU"
 
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falso innesco"
+
 # MSG_FAN_SPEED c=14
 #: messages.c:31
 msgid "Fan speed"
 msgstr "Velocita ventola"
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test ventola"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5561
 msgid "Fans check   [on]"
-msgstr "Controllo ventole [on]"
+msgstr "Control.vent[on]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5563
 msgid "Fans check  [off]"
 msgstr "Control.vent[off]"
 
@@ -653,7 +693,7 @@ msgid "Fil. sensor response is poor, disable it?"
 msgstr "Risposta Sens. Fil. debole, disattivare? "
 
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5046
 msgid "Fil. sensor [N/A]"
 msgstr "Sensor filam[N/A]"
 
@@ -663,7 +703,7 @@ msgid "Fil. sensor [off]"
 msgstr "Sensor filam[off]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Filam. runouts"
 msgstr "Filam. esauriti"
 
@@ -678,12 +718,12 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filamento estruso & con il giusto colore?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2669
 msgid "Filament not loaded"
 msgstr "Fil. non caricato"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Sensore filam."
 
@@ -693,7 +733,7 @@ msgid "Filament sensor:"
 msgstr "Sensore filam.:"
 
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2838
 msgid "Filament used"
 msgstr "Filamento utilizzato"
 
@@ -703,7 +743,7 @@ msgid "Filament used:  "
 msgstr "Filamento usato:"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "File incompleto. Continuare comunque?"
 
@@ -717,53 +757,103 @@ msgstr "File aperto: "
 msgid "File selected"
 msgstr "File selezionato"
 
+# 
+#: ultralcd.cpp:3943
+msgid "FINDA:"
+msgstr "FINDA:"
+
 # MSG_FINISHING_MOVEMENTS c=20 r=1
 #: messages.c:40
 msgid "Finishing movements"
 msgstr "Finalizzando gli spostamenti"
 
+# 
+#: ultralcd.cpp:5443
+msgid "Firmware   [none]"
+msgstr "Firmware [nessuno]"
+
+# 
+#: ultralcd.cpp:5446
+msgid "Firmware   [warn]"
+msgstr "Firmware [avviso]"
+
+# 
+#: ultralcd.cpp:5449
+msgid "Firmware [strict]"
+msgstr "Firmware [esatto]"
+
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Calibrazione primo layer."
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4880
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Per primo avviero l'autotest per controllare gli errori di assemblaggio piu comuni."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Risolvi il problema e quindi premi il bottone sull'unita MMU. "
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Flusso"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2099
 msgid "forum.prusa3d.com"
 msgstr "forum.prusa3d.com"
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Ventola frontale?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3217
 msgid "Front side[um]"
 msgstr "Fronte [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Ventola frontale/sinistra"
 
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr "G-code processato per un livello diverso. Continuare?"
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr "G-code processato per un livello diverso. Per favore esegui nuovamente lo slice del modello. Stampa annullata."
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr "G-code processato per una stampante diversa. Continuare?"
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr "G-code processato per una stampante diversa. Per favore esegui nuovamente lo slice del modello. Stampa annullata."
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr "G-code processato per un firmware più recente. Continuare?"
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr "G-code processato per un firmware più recente. Per favore aggiorna il firmware. Stampa annullata."
+
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Riscald./Termist."
 
@@ -773,7 +863,7 @@ msgid "Heating"
 msgstr "Riscaldamento..."
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8411
 msgid "Heating disabled by safety timer."
 msgstr "Riscaldamento fermato dal timer di sicurezza."
 
@@ -783,27 +873,32 @@ msgid "Heating done."
 msgstr "Riscald. completo"
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4859
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Ciao, sono la tua stampante Original Prusa i3. Gradiresti un aiuto nel processo di configurazione?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2100
 msgid "howto.prusa3d.com"
 msgstr "howto.prusa3d.com"
 
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "Installazione HW"
+
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4889
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Adesso avviero una Calibrazione XYZ. Puo durare circa 12 min."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4897
 msgid "I will run z calibration now."
 msgstr "Adesso avviero la Calibrazione Z."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4962
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Adesso iniziero a stampare una linea e tu dovrai abbassare l'ugello poco per volta ruotando la manopola sino a raggiungere una altezza ottimale. Per favore dai uno sguardo all'immagine del nostro manuale, cap.Calibrazione."
 
@@ -813,7 +908,7 @@ msgid "Improving bed calibration point"
 msgstr "Perfezion. punto di calibraz. letto"
 
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Schermata info"
 
@@ -823,7 +918,7 @@ msgid "Init. SD card"
 msgstr "Inizializza scheda SD"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2569
 msgid "Insert filament"
 msgstr "Inserire filamento"
 
@@ -848,27 +943,32 @@ msgid "Insert filament into extruder 4. Click when done."
 msgstr "Inserire filamento nell'estrusore 4. Click per continuare"
 
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:3947
+msgid "IR:"
+msgstr "IR:"
+
+# 
+#: ultralcd.cpp:4922
 msgid "Is filament 1 loaded?"
 msgstr "Il filamento 1 e caricato?"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4925
 msgid "Is filament loaded?"
 msgstr "Il filamento e stato caricato?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4956
 msgid "Is it PLA filament?"
 msgstr "E' un filamento di PLA?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4701
 msgid "Is PLA filament loaded?"
 msgstr "E' stato caricato il filamento di PLA?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "La piastra d'acciaio e sul piano riscaldato?"
 
@@ -883,29 +983,29 @@ msgid "KILLED. "
 msgstr "IN TILT."
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1828
 msgid "Last print"
 msgstr "Ultima stampa"
 
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1845
 msgid "Last print failures"
 msgstr "Fallimenti ultima stampa"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2967
 msgid "Left"
 msgstr "Sinistra"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Vent SX hotend?"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3215
 msgid "Left side [um]"
-msgstr "Lato sinistro [um]"
+msgstr "Sinistra [um]"
 
 # MSG_LEFT c=12 r=1
 #: ultralcd.cpp:2308
@@ -913,7 +1013,7 @@ msgid "Left:"
 msgstr "Sinistra:"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5575
 msgid "Lin. correction"
 msgstr "Correzione lin."
 
@@ -923,7 +1023,7 @@ msgid "Live adjust Z"
 msgstr "Compensazione Z"
 
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6059
 msgid "Load all"
 msgstr "Caricare tutti"
 
@@ -958,12 +1058,12 @@ msgid "Load filament 5"
 msgstr "Caricare fil. 5"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6714
 msgid "Load to nozzle"
 msgstr "Carica ugello"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2609
 msgid "Loading color"
 msgstr "Caricando colore"
 
@@ -973,7 +1073,7 @@ msgid "Loading filament"
 msgstr "Caricando filamento"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Puleggia lenta"
 
@@ -993,7 +1093,7 @@ msgid "M109 Invalid extruder "
 msgstr "M109 Estrusore non valido"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Calibrazione primo layer."
 
@@ -1012,8 +1112,23 @@ msgstr "M218 Estrusore non valido"
 msgid "M221 Invalid extruder "
 msgstr "M221 Estrusore non valido"
 
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Comp. Magneti [on]"
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Comp. Magneti [N/A]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Comp. Magneti [off]"
+
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Menu principale"
 
@@ -1023,9 +1138,9 @@ msgid "Mark filament 100mm from extruder body. Click when done."
 msgstr "Segnare il filamento a 100 mm di distanza dal corpo dell'estrusore. Click per continuare."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3002
 msgid "Measured skew"
-msgstr "Disassamento misurato"
+msgstr "Deviazione misurata"
 
 # MSG_MEASURED_SKEW c=15 r=1
 #: ultralcd.cpp:2335
@@ -1033,32 +1148,67 @@ msgid "Measured skew:"
 msgstr "Distorsione misurata:"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Misura altezza di rif. del punto di calib."
 
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Griglia [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Griglia [7x7]"
+
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5658
 msgid "Mesh Bed Leveling"
 msgstr "Mesh livel. letto"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:5572
+msgid "Mesh bed leveling"
+msgstr "Mesh livel. letto"
+
+# 
+#: Marlin_main.cpp:881
+msgid "MK3 firmware detected on MK3S printer"
+msgstr "Rilevato firmware MK3 su stampante MK3S"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr "Firmware MK3S rilevato su stampante MK3"
+
+# 
+#: ultralcd.cpp:1845
 msgid "MMU fails"
 msgstr "Fallimenti MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1617
 msgid "MMU load failed     "
 msgstr "Caricamento MMU fallito"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1845
 msgid "MMU load fails"
 msgstr "Caricamenti MMU falliti"
 
 # 
-#: mmu.cpp:635
+#: ultralcd.cpp:5204
+msgid "MMU Mode [Normal]"
+msgstr "Modalità MMU [Normale]"
+
+# 
+#: ultralcd.cpp:5205
+msgid "MMU Mode[Stealth]"
+msgstr "Modalità MMU [Silenziosa]"
+
+# 
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "Il MMU richiede attenzione dall'utente."
 
@@ -1068,82 +1218,102 @@ msgid "MMU needs user attention. Fix the issue and then press button on MMU unit
 msgstr "MMU richiede l'attenzione dell'utente. Risolvi il problema e quindi premi il bottone sull'unità MMU. "
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. riprendendo la posizione... "
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Ripristino temperatura... "
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Riprendendo... "
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "MMU power fails"
 msgstr "Mancanza corrente MMU"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2112
 msgid "MMU2 connected"
 msgstr "MMU2 connessa"
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Modo    [normale]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Modo [silenzioso]"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Modo [Silenziosa]"
 
+# 
+#: ultralcd.cpp:4424
+msgid "Mode change in progress ..."
+msgstr "Cambio modalità in corso ..."
+
 # MSG_AUTO_MODE_ON
 #: messages.c:12
 msgid "Mode [auto power]"
 msgstr "Modo       [auto]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Mode      [forte]"
 
+# 
+#: ultralcd.cpp:5404
+msgid "Model      [none]"
+msgstr "Modello [nessuno]"
+
+# 
+#: ultralcd.cpp:5407
+msgid "Model      [warn]"
+msgstr "Modello [avviso]"
+
+# 
+#: ultralcd.cpp:5410
+msgid "Model    [strict]"
+msgstr "Modello [esatto]"
+
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Motore"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5550
 msgid "Move axis"
 msgstr "Muovi asse"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4291
 msgid "Move X"
-msgstr "Muovi X"
+msgstr "Sposta X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4292
 msgid "Move Y"
-msgstr "Muovi Y"
+msgstr "Sposta Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4293
 msgid "Move Z"
-msgstr "Muovi Z"
+msgstr "Sposta Z"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2973
 msgid "N/A"
 msgstr "N/A"
 
@@ -1153,7 +1323,7 @@ msgid "New firmware version available:"
 msgstr "Nuova versione firmware disponibile:"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "No"
 
@@ -1168,12 +1338,12 @@ msgid "No Checksum with line number, Last Line: "
 msgstr "Nessun checksum con numero di riga, ultima riga:"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5254
 msgid "No move."
 msgstr "Nessun movimento."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6694
 msgid "No SD card"
 msgstr "Nessuna SD"
 
@@ -1183,37 +1353,67 @@ msgid "No thermistors - no temperature"
 msgstr "No termistore - no temperatura"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Non connesso"
 
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Non gira"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4961
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Adesso calibro la distanza fra ugello e superfice del piatto."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4905
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Adesso preriscaldero l'ugello per PLA."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4896
 msgid "Now remove the test print from steel sheet."
 msgstr "Ora rimuovete la stampa di prova dalla piastra in acciaio."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Ugello"
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:5319
+msgid "Nozzle     [none]"
+msgstr "Ugello [nessuno]"
+
+# 
+#: ultralcd.cpp:5322
+msgid "Nozzle     [warn]"
+msgstr "Ugello [avviso]"
+
+# 
+#: ultralcd.cpp:5325
+msgid "Nozzle   [strict]"
+msgstr "Ugello [esatto]"
+
+# 
+#: ultralcd.cpp:5365
+msgid "Nozzle d.  [0.25]"
+msgstr "Diam. Ugello [0.25]"
+
+# 
+#: ultralcd.cpp:5368
+msgid "Nozzle d.  [0.40]"
+msgstr "Diam. Ugello [0.40]"
+
+# 
+#: ultralcd.cpp:5371
+msgid "Nozzle d.  [0.60]"
+msgstr "Diam. Ugello [0.60]"
+
+# 
+#: ultralcd.cpp:1787
 msgid "Nozzle FAN"
 msgstr "Ventola estrusore"
 
@@ -1238,9 +1438,9 @@ msgid "ok"
 msgstr "ok"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1535
 msgid "Old settings found. Default PID, Esteps etc. will be set."
-msgstr "Sono state trovate impostazioni vecchie. I valori di default di PID, Esteps etc. saranno impostati"
+msgstr "Sono state trovate impostazioni vecchie. Verranno impostati i valori predefiniti di PID, Esteps etc."
 
 # MSG_ENDSTOP_OPEN
 #: messages.c:29
@@ -1258,7 +1458,7 @@ msgid "openRoot failed"
 msgstr "openRoot fallito"
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6657
 msgid "Pause print"
 msgstr "Metti in pausa"
 
@@ -1268,42 +1468,47 @@ msgid "Pick print"
 msgstr "Scegli stampa"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1613
 msgid "PID cal.           "
 msgstr "Calibrazione PID"
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1619
 msgid "PID cal. finished"
 msgstr "Calib. PID completa"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5664
 msgid "PID calibration"
 msgstr "Calibrazione PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:862
 msgid "PINDA Heating"
 msgstr "Riscaldamento PINDA"
 
+# 
+#: ultralcd.cpp:3939
+msgid "PINDA:"
+msgstr "PINDA:"
+
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Posizionare un foglio sotto l'ugello durante la calibrazione dei primi 4 punti. In caso l'ugello muova il foglio spegnere subito la stampante."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Verifica:"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Per favore consulta il nostro manuale per risolvere il problema. Poi riprendi il Wizard dopo aver riavviato la stampante."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4970
 msgid "Please clean heatbed and then press the knob."
 msgstr "Per favore pulisci il piatto, poi premi la manopola."
 
@@ -1313,12 +1518,12 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Pulire l'ugello per la calibrazione, poi fare click."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4804
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Per favore inserisci il filamento di PLA nell'estrusore, poi premi la manopola per caricare."
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4800
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Per favore inserite del filamento PLA nel primo tubo del MMU, poi premete la manopola per caricarlo."
 
@@ -1328,52 +1533,52 @@ msgid "Please load PLA filament and then resume Wizard by rebooting the printer.
 msgstr "Per favore carica filamento di PLA e riprendi il Wizard dopo aver riavviato la stampante."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4706
 msgid "Please load PLA filament first."
 msgstr "Per favore prima carica il filamento di PLA."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3083
 msgid "Please open idler and remove filament manually."
 msgstr "Aprire la guida filam. e rimuovere il filam. a mano"
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Per favore posizionate la piastra d'acciaio sul piano riscaldato."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Premete la manopola per scaricare il filamento "
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Estrarre il filamento immediatamente"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1441
 msgid "Please remove filament and then press the knob."
 msgstr "Rimuovi il filamento e quindi premi la manopola. "
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4895
 msgid "Please remove shipping helpers first."
 msgstr "Per favore rimuovete i materiali da spedizione"
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Rimuovete la piastra di acciaio dal piano riscaldato"
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4317
 msgid "Please run XYZ calibration first."
 msgstr "Esegui la calibrazione XYZ prima. "
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1360
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Aggiorna il firmware sul tuo MMU2. In attesa di reset. "
 
@@ -1383,12 +1588,12 @@ msgid "Please upgrade."
 msgstr "Prego aggiornare."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Attendere"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Power failures"
 msgstr "Mancanza corrente"
 
@@ -1398,27 +1603,37 @@ msgid "PowerUp"
 msgstr "Accendi"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6644
 msgid "Preheat"
 msgstr "Preriscalda"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Prerisc. ugello!"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Preriscaldando l'ugello. Attendere prego."
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2290
+msgid "Preheating to cut"
+msgstr "Preriscaldamento per taglio"
+
+# 
+#: ultralcd.cpp:2287
+msgid "Preheating to eject"
+msgstr "Preriscaldamento per espulsione"
+
+# 
+#: ultralcd.cpp:2280
 msgid "Preheating to load"
 msgstr "Preriscaldamento per caricare"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2284
 msgid "Preheating to unload"
 msgstr "Preriscaldamento per scaricare"
 
@@ -1428,27 +1643,27 @@ msgid "Prepare new filament"
 msgstr "Preparare il nuovo filamento"
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10312
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Premete la manopola per preriscaldare l'ugello e continuare."
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2210
 msgid "Press the knob"
 msgstr "Premere la manopola"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Premete la manopola per recuperare la temperatura dell'ugello."
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Stampa interrotta"
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1789
 msgid "Print FAN"
 msgstr "Ventola di stampa"
 
@@ -1458,7 +1673,7 @@ msgid "Print FAN: "
 msgstr "Ventola di stampa:"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Ventola di stampa:"
 
@@ -1468,12 +1683,12 @@ msgid "Print from SD"
 msgstr "Stampa da SD"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1080
 msgid "Print paused"
 msgstr "Stampa in pausa"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2838
 msgid "Print time"
 msgstr "Tempo di stampa"
 
@@ -1487,6 +1702,26 @@ msgstr "Tempo di stampa:"
 msgid "Printer disconnected"
 msgstr "Stampante sconnessa"
 
+# 
+#: util.cpp:473
+msgid "Printer FW version differs from the G-code. Continue?"
+msgstr "Versione FW stampante diversa dal G-Code. Continuare?"
+
+# 
+#: util.cpp:480
+msgid "Printer FW version differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Versione FW stampante diversa dal G-Code. Controlla il valore nelle impostazioni. Stampa annullata."
+
+# 
+#: util.cpp:506
+msgid "Printer G-code level differs from the G-code. Continue?"
+msgstr "Il livello G-code della stampante è diverso dal G-Code. Continuare?"
+
+# 
+#: util.cpp:513
+msgid "Printer G-code level differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Il livello G-code della stampante è diverso dal G-Code. Controlla il valore nelle impostazioni. Stampa annullata."
+
 # MSG_ERR_KILLED
 #: Marlin_main.cpp:7547
 msgid "Printer halted. kill() called!"
@@ -1497,6 +1732,26 @@ msgstr "Stampante ferma. kill () chiamato!"
 msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
 msgstr "Stampante non ancora calibrata. Si prega di seguire il manuale, capitolo Primi Passi, sezione Sequenza di Calibrazione."
 
+# 
+#: util.cpp:423
+msgid "Printer model differs from the G-code. Continue?"
+msgstr "Modello stampante diversa dal G-Code. Continuare?"
+
+# 
+#: util.cpp:430
+msgid "Printer model differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Il modello stampante è diverso dal G-Code. Controlla il valore nelle impostazioni. Stampa annullata."
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Diametro ugello diverso da G-Code. Continuare?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Diametro ugello diverso dal G-Code. Controlla il valore nelle impostazioni. Stampa annullata."
+
 # MSG_ERR_STOPPED
 #: messages.c:32
 msgid "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
@@ -1512,6 +1767,11 @@ msgstr "Prusa i3 MK2 pronta."
 msgid "Prusa i3 MK2.5 ready."
 msgstr "Prusa i3 MK2.5 ready."
 
+# 
+#:
+msgid "Prusa i3 MK3 OK."
+msgstr "Prusa i3 MK3 OK."
+
 # WELCOME_MSG c=20
 #:
 msgid "Prusa i3 MK3 ready."
@@ -1523,17 +1783,17 @@ msgid "Prusa i3 MK3S OK."
 msgstr "Prusa i3 MK3S OK."
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2098
 msgid "prusa3d.com"
 msgstr "prusa3d.com"
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3218
 msgid "Rear side [um]"
 msgstr "Retro [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9712
 msgid "Recovering print    "
 msgstr "Recupero stampa"
 
@@ -1543,10 +1803,15 @@ msgid "Refresh"
 msgstr "Refresh"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Rimuovi il filamento precedente e premi la manopola per caricare il nuovo filamento. "
 
+# 
+#: ultralcd.cpp:6605
+msgid "Rename"
+msgstr "Rinomina"
+
 # MSG_M119_REPORT
 #: Marlin_main.cpp:5297
 msgid "Reporting endstop status"
@@ -1563,32 +1828,32 @@ msgid "Resend: "
 msgstr "Invia di nuovo: "
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3219
 msgid "Reset"
 msgstr "Reset"
 
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5669
 msgid "Reset XYZ calibr."
 msgstr "Reset calibrazione XYZ."
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6664
 msgid "Resume print"
 msgstr "Riprendi stampa"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Riprendi stampa"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2968
 msgid "Right"
 msgstr "Destra"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3216
 msgid "Right side[um]"
 msgstr "Destra [um]"
 
@@ -1603,22 +1868,22 @@ msgid "Rotate knob until mark reaches extruder body. Click when done."
 msgstr "Ruota la manopola finchè il segno raggiunga il corpo dell'estrusore. Clicca per continuare."
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5587
 msgid "RPi port     [on]"
 msgstr "Porta RPi    [on]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5585
 msgid "RPi port    [off]"
 msgstr "Porta RPi   [off]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4723
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Se avvi il Wizard perderai la calibrazione preesistente e dovrai ricominciare dall'inizio. Continuare?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5220
 msgid "SD card  [normal]"
 msgstr "Mem. SD [normale]"
 
@@ -1633,7 +1898,7 @@ msgid "SD card [FlshAir]"
 msgstr "Mem. SD [FlashAir]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5218
 msgid "SD card [flshAir]"
 msgstr "Mem. SD [flshAir]"
 
@@ -1652,53 +1917,63 @@ msgstr "SD stampa byte "
 msgid "Searching bed calibration point"
 msgstr "Ricerca dei punti di calibrazione del piano"
 
+# 
+#: ultralcd.cpp:6601
+msgid "Select"
+msgstr "Seleziona"
+
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5594
 msgid "Select language"
 msgstr "Seleziona lingua"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4943
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Selezionate la temperatura per il preriscaldamento dell'ugello adatta al vostro materiale."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Select PLA filament:"
 msgstr "Selezionate filamento PLA:"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Autotest OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Avvia autotest"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5645
 msgid "Selftest         "
 msgstr "Autotest"
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Errore Autotest !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Autotest fallito"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1567
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Verra effettuato un self test per calibrare l'homing senza sensori"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:2138
+msgid "Sensor info"
+msgstr "Info Sensore"
+
+# 
+#: ultralcd.cpp:3938
 msgid "Sensor state"
 msgstr "Stato sensore"
 
@@ -1708,27 +1983,32 @@ msgid "Sensors info"
 msgstr "Info Sensori"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3227
 msgid "Set temperature:"
 msgstr "Imposta temperatura:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Impostazioni"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3005
 msgid "Severe skew"
-msgstr "Disassamento grave"
+msgstr "Deviazione grave"
 
 # MSG_SEVERE_SKEW c=15 r=1
 #: ultralcd.cpp:2346
 msgid "Severe skew:"
 msgstr "Distorsione grave:"
 
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Piano"
+
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5666
 msgid "Show end stops"
 msgstr "Stato finecorsa"
 
@@ -1743,9 +2023,9 @@ msgid "Sleep..."
 msgstr "Sospensione..."
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3004
 msgid "Slight skew"
-msgstr "Disassamento lieve"
+msgstr "Deviazione lieve"
 
 # MSG_SLIGHT_SKEW c=15 r=1
 #: ultralcd.cpp:2342
@@ -1753,15 +2033,30 @@ msgid "Slight skew:"
 msgstr "Distorsione leggera:"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Alcuni file non saranno ordinati. Il numero massimo di file in una cartella e 100 perche siano ordinati."
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4833
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Sono stati rilevati problemi, avviato livellamento Z ..."
 
+# MSG_SORT_NONE c=17 r=1
+#: ultralcd.cpp:5230
+msgid "Sort       [none]"
+msgstr "Ordina [nessuno]"
+
+# MSG_SORT_TIME c=17 r=1
+#: ultralcd.cpp:5228
+msgid "Sort       [time]"
+msgstr "Ordina [tempo]"
+
+# MSG_SORT_ALPHA c=17 r=1
+#: ultralcd.cpp:5229
+msgid "Sort   [alphabet]"
+msgstr "Ordine [alfabetico]"
+
 # MSG_SORT_NONE c=17 r=1
 #: ultralcd.cpp:4250
 msgid "Sort:      [None]"
@@ -1803,117 +2098,132 @@ msgid "Sort:  [time]"
 msgstr "Ordina: [time]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Ordinando i file"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Suono     [forte]"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#:
 msgid "Sound      [mute]"
 msgstr "Suono      [mute]"
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Suono   [singolo]"
 
+# 
+#:
+msgid "Sound     [assist]"
+msgstr "Suono [assistito]"
+
+# 
+#: sound.h:9
+msgid "Sound     [blind]"
+msgstr "Suono [cieco]"
+
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Suono[silenzioso]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Velocita"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Gira"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5098
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin    [on]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5094
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin   [N/A]"
 
 # MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+#: ultralcd.cpp:5102
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [off]"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4330
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Sono necessari una temperatura ambiente di 21-26C e una superficie rigida "
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statistiche"
 
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr "Piani d'acciaio"
+
 # MSG_STEPPER_TOO_HIGH
 #: stepper.cpp:345
 msgid "Steprate too high: "
 msgstr "Velocità passo troppo alta: "
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
 msgstr "Arresta stampa"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ARRESTATO."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Supporto"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Scambiato"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Calib. temp. "
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5581
 msgid "Temp. cal.   [on]"
 msgstr "Calib. temp. [ON]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5579
 msgid "Temp. cal.  [off]"
 msgstr "Calib. temp.[OFF]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5675
 msgid "Temp. calibration"
 msgstr "Calib. Temp."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5548
 msgid "Temperature"
 msgstr "Temperatura"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3864
 msgid "Temperature calibration failed"
 msgstr "Calibrazione temperatura fallita"
 
@@ -1923,12 +2233,12 @@ msgid "Temperature calibration has not been run yet"
 msgstr "Calibrazione della temperatura non ancora eseguita"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Calibrazione temperatura completata e attiva. Puo essere disattivata dal menu Impostazioni ->Cal. Temp."
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2144
 msgid "Temperatures"
 msgstr "Temperature"
 
@@ -1938,27 +2248,27 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "E ancora necessario effettuare la calibrazione Z. Segui il manuale, capitolo Primi Passi, sezione Sequenza di Calibrazione. "
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2217
 msgid "to load filament"
 msgstr "per caricare il filamento"
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2221
 msgid "to unload filament"
 msgstr "per scaricare il filamento"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1829
 msgid "Total"
 msgstr "Totale"
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "Total failures"
 msgstr "Totale fallimenti"
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2860
 msgid "Total filament"
 msgstr "Filamento totale"
 
@@ -1968,7 +2278,7 @@ msgid "Total filament :"
 msgstr "Filamento tot:"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2860
 msgid "Total print time"
 msgstr "Tempo di stampa totale"
 
@@ -1983,17 +2293,17 @@ msgid "TRIGGERED"
 msgstr "ATTIVATO"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6641
 msgid "Tune"
 msgstr "Regola"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2120
 msgid "unknown"
 msgstr "sconosciuto"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Unload"
 msgstr "Scarica"
 
@@ -2003,9 +2313,9 @@ msgid "Unload all"
 msgstr "Rilasciare tutti"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
-msgstr "Scarica filam."
+msgstr "Scarica filamento"
 
 # MSG_UNLOAD_FILAMENT_1 c=17
 #: ultralcd.cpp:5406
@@ -2028,22 +2338,22 @@ msgid "Unload filament 4"
 msgstr "Scarica filam. 4"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Scaricando filamento"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4779
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Usate lo scaricamento per rimuovere il filamento 1 se protrude dal retro del tubo posteriore del MMu. Utilizzate l'espulsione se e nascosto nel tubo."
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5803
 msgid "Used during print"
 msgstr "Usati nella stampa"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2147
 msgid "Voltages"
 msgstr "Voltaggi"
 
@@ -2053,32 +2363,37 @@ msgid "volume.init failed"
 msgstr "volume.init fallito"
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5225
 msgid "Wait for user..."
 msgstr "Attendendo utente..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3371
 msgid "Waiting for nozzle and bed cooling"
 msgstr "In attesa del raffreddamento dell'ugello e del piano"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3335
 msgid "Waiting for PINDA probe cooling"
 msgstr "In attesa del raffreddamento della sonda PINDA"
 
+# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
+#:
+msgid "WARNING:\nCrash detection\ndisabled in\nStealth mode"
+msgstr "ATTENZIONE:\nRilevamento impatto\ndisattivato in\nModalità Silenziosa"
+
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1527
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Attenzione: tipo di stampante e di scheda madre cambiati."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1519
 msgid "Warning: motherboard type changed."
 msgstr "Avviso: tipo di scheda madre cambiato"
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1523
 msgid "Warning: printer type changed."
 msgstr "Avviso: tipo di stampante cambiato."
 
@@ -2088,17 +2403,17 @@ msgid "WARNING: This is an unofficial, unsupported build. Use at your own risk!"
 msgstr "ATTENZIONE: Questo è un build non ufficiale, non supportato. Utilizzatelo a vostro rischio!"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3072
 msgid "Was filament unload successful?"
 msgstr "Filamento scaricato con successo?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Errore cablaggio"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5642
 msgid "Wizard"
 msgstr "Wizard"
 
@@ -2117,23 +2432,28 @@ msgstr "Scrittura su file: "
 msgid "X-correct"
 msgstr "Correzione-X"
 
+# 
+#: ultralcd.cpp:5028
+msgid "X-correct:"
+msgstr "Correzione-X:"
+
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2136
 msgid "XYZ cal. details"
 msgstr "XYZ Cal. dettagli"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Calibrazione XYZ corretta. La distorsione verra compensata automaticamente."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3832
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Calibrazion XYZ corretta. Assi X/Y leggermente storti. Ben fatto!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3813
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Calibrazione XYZ compromessa. Punti anteriori non raggiungibili."
 
@@ -2143,17 +2463,17 @@ msgid "XYZ calibration compromised. Left front calibration point not reachable."
 msgstr "Calibrazione XYZ compromessa. Punto anteriore sinistro non raggiungibile."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Calibrazione XYZ compromessa. Punto anteriore destro non raggiungibile."
 
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3795
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Calibrazione XYZ fallita. Il punto di calibrazione sul letto non e' stato trovato."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3801
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Calibrazione XYZ fallita. Punti anteriori non raggiungibili."
 
@@ -2168,17 +2488,17 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Calibrazione XYZ fallita. Si prega di consultare il manuale."
 
 # 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Calibrazione XYZ fallita. Punto anteriore destro non raggiungibile."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3829
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Calibrazione XYZ OK. Gli assi X/Y sono perpendicolari. Complimenti!"
 
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2965
 msgid "Y distance from min"
 msgstr "Distanza Y dal min"
 
@@ -2192,8 +2512,13 @@ msgstr "Distanza Y da min:"
 msgid "Y-correct"
 msgstr "Correzione-Y"
 
+# 
+#: ultralcd.cpp:5029
+msgid "Y-correct:"
+msgstr "Correzione-Y:"
+
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Si"
 
@@ -2208,11 +2533,26 @@ msgid "You are using firmware beta version. This is development version. Using t
 msgstr "State utilizzando una versione beta del firmware. Questa versione è in via di sviluppo. L'utilizzo non è raccomandato e potrebbe causare danni alla stampante."
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "E possibile riprendere il Wizard in qualsiasi momento attraverso Calibrazione -> Wizard."
 
+# 
+#: ultralcd.cpp:5030
+msgid "Z-correct:"
+msgstr "Correzione-Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Z-probe nr. [1]"
+
+# 
+#: ultralcd.cpp:6954
+msgid "Z-probe nr.    [3]"
+msgstr "Z-probe nr. [3]"
+
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3024
 msgid "[0;0] point offset"
 msgstr "[0;0] punto offset"

lang/po/new/pl.po

@@ -17,6 +17,11 @@ msgstr "\e[2JWykrywanie zderzen moze\e[1;0Hbyc wlaczone tylko w\e[2;0Htrybie Nor
 msgid "\e[2JWARNING:\e[1;0HCrash detection\e[2;0Hdisabled in\e[3;0HStealth mode"
 msgstr "\e[2JUWAGA:\e[1;0HWykrywanie zderzen\e[2;0Hwylaczone w\e[3;0Htrybie Stealth"
 
+# 
+#: ultralcd.cpp:3913
+msgid "  1"
+msgstr "1"
+
 # MSG_PLANNER_BUFFER_BYTES
 #: Marlin_main.cpp:1184
 msgid "  PlannerBufferBytes: "
@@ -48,10 +53,15 @@ msgid " of 4"
 msgstr " z 4"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE2 c=14
-#: messages.c:56
+#: messages.c:60
 msgid " of 9"
 msgstr " z 9"
 
+# MSG_OFF
+#: menu.cpp:426
+msgid " [off]"
+msgstr "[wyl]"
+
 # MSG_FACTOR
 #: ultralcd.cpp:6008
 msgid " \002 Fact"
@@ -68,7 +78,7 @@ msgid " \002 Min"
 msgstr " \002 Min"
 
 # 
-#: ultralcd.cpp:2353
+#: ultralcd.cpp:2294
 msgid ">Cancel"
 msgstr ">Anuluj"
 
@@ -77,35 +87,40 @@ msgstr ">Anuluj"
 msgid "Adjusting Z"
 msgstr "Dostrajanie Z"
 
+# MSG_BABYSTEPPING_Z c=15
+#: ultralcd.cpp:3144
+msgid "Adjusting Z:"
+msgstr "Ustawianie Z:"
+
 # MSG_ALL c=19 r=1
 #: messages.c:11
 msgid "All"
 msgstr "Wszystko"
 
 # MSG_SELFTEST_CHECK_ALLCORRECT c=20
-#: ultralcd.cpp:7459
+#: ultralcd.cpp:8209
 msgid "All correct      "
 msgstr "Wszystko OK "
 
 # MSG_WIZARD_DONE c=20 r=8
-#: messages.c:95
+#: messages.c:101
 msgid "All is done. Happy printing!"
 msgstr "Gotowe. Udanego drukowania!"
 
 # 
-#: ultralcd.cpp:2109
+#: ultralcd.cpp:1979
 msgid "Ambient"
 msgstr "Otoczenie"
 
 # MSG_PRESS c=20
-#: ultralcd.cpp:2463
+#: ultralcd.cpp:2573
 msgid "and press the knob"
 msgstr "i nacisnij pokretlo"
 
 # MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
-#: ultralcd.cpp:3330
+#: ultralcd.cpp:3442
 msgid "Are left and right Z~carriages all up?"
-msgstr "Obydwa konce osi dojechaly do gornych ogranicznikow?"
+msgstr "Obydwa konce osi sa na szczycie?"
 
 # MSG_ADJUSTZ
 #: ultralcd.cpp:2600
@@ -133,27 +148,27 @@ msgid "Auto home"
 msgstr "Auto zerowanie"
 
 # MSG_AUTOLOAD_FILAMENT c=17
-#: ultralcd.cpp:6091
+#: ultralcd.cpp:6731
 msgid "AutoLoad filament"
 msgstr "AutoLadowanie fil."
 
 # MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
-#: ultralcd.cpp:4246
+#: ultralcd.cpp:4375
 msgid "Autoloading filament available only when filament sensor is turned on..."
 msgstr "Autoladowanie filamentu dostepne tylko gdy czujnik filamentu jest wlaczony..."
 
 # MSG_AUTOLOADING_ENABLED c=20 r=4
-#: ultralcd.cpp:2655
+#: ultralcd.cpp:2768
 msgid "Autoloading filament is active, just press the knob and insert filament..."
 msgstr "Autoladowanie filamentu wlaczone, nacisnij pokretlo i wsun filament..."
 
 # MSG_SELFTEST_AXIS
-#: ultralcd.cpp:7130
+#: ultralcd.cpp:7865
 msgid "Axis"
 msgstr "Os"
 
 # MSG_SELFTEST_AXIS_LENGTH
-#: ultralcd.cpp:7128
+#: ultralcd.cpp:7863
 msgid "Axis length"
 msgstr "Dlugosc osi"
 
@@ -167,13 +182,18 @@ msgstr "Babystepping X"
 msgid "Babystepping Y"
 msgstr "Babystepping Y"
 
+# 
+#: messages.c:57
+msgid "Back"
+msgstr "Wstecz"
+
 # MSG_BED
 #: messages.c:15
 msgid "Bed"
 msgstr "Stol"
 
 # MSG_SELFTEST_BEDHEATER
-#: ultralcd.cpp:7072
+#: ultralcd.cpp:7807
 msgid "Bed / Heater"
 msgstr "Stol / Grzanie"
 
@@ -188,7 +208,7 @@ msgid "Bed Heating"
 msgstr "Grzanie stolu.."
 
 # MSG_BED_CORRECTION_MENU
-#: ultralcd.cpp:5197
+#: ultralcd.cpp:5663
 msgid "Bed level correct"
 msgstr "Korekta poziomowania stolu"
 
@@ -213,17 +233,17 @@ msgid "Begin file list"
 msgstr "Poczatek listy plikowogranicznikow"
 
 # MSG_MENU_BELT_STATUS c=15 r=1
-#: ultralcd.cpp:2135
+#: ultralcd.cpp:2007
 msgid "Belt status"
 msgstr "Stan paskow"
 
 # MSG_RECOVER_PRINT c=20 r=2
-#: messages.c:67
+#: messages.c:71
 msgid "Blackout occurred. Recover print?"
 msgstr "Wykryto zanik napiecia. Kontynowac?"
 
 # MSG_CALIBRATE_PINDA c=17 r=1
-#: ultralcd.cpp:4427
+#: ultralcd.cpp:4566
 msgid "Calibrate"
 msgstr "Kalibruj"
 
@@ -233,7 +253,7 @@ msgid "Calibrate E"
 msgstr "Kalibruj E"
 
 # MSG_CALIBRATE_BED
-#: ultralcd.cpp:5186
+#: ultralcd.cpp:5652
 msgid "Calibrate XYZ"
 msgstr "Kalibracja XYZ"
 
@@ -243,12 +263,12 @@ msgid "Calibrate Z"
 msgstr "Kalibruj Z"
 
 # 
-#: ultralcd.cpp:7461
+#: ultralcd.cpp:8211
 msgid "Calibrating home"
 msgstr "Zerowanie osi"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibracja XYZ. Przekrec pokretlo, aby przesunac os Z do gornych ogranicznikow. Nacisnij, by potwierdzic."
 
@@ -258,22 +278,22 @@ msgid "Calibrating Z"
 msgstr "Kalibruje Z"
 
 # MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
-#: ultralcd.cpp:3290
+#: ultralcd.cpp:3405
 msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
 msgstr "Kalibracja XYZ. Przekrec pokretlo, aby przesunac os Z do gornych ogranicznikow. Nacisnij, by potwierdzic."
 
 # MSG_MENU_CALIBRATION
-#: messages.c:57
+#: messages.c:61
 msgid "Calibration"
 msgstr "Kalibracja"
 
 # MSG_HOMEYZ_DONE
-#: ultralcd.cpp:778
+#: ultralcd.cpp:832
 msgid "Calibration done"
 msgstr "Kalibracja OK"
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Cancel"
 msgstr "Anuluj"
 
@@ -293,7 +313,7 @@ msgid "Card inserted"
 msgstr "Karta wlozona"
 
 # MSG_SD_REMOVED
-#: ultralcd.cpp:7819
+#: ultralcd.cpp:8578
 msgid "Card removed"
 msgstr "Karta wyjeta"
 
@@ -313,12 +333,12 @@ msgid "Change SD card"
 msgstr "Wymien karte SD"
 
 # MSG_CHANGE_SUCCESS
-#: ultralcd.cpp:2474
+#: ultralcd.cpp:2584
 msgid "Change success!"
 msgstr "Wymiana ok!"
 
 # MSG_CORRECTLY c=20
-#: ultralcd.cpp:2551
+#: ultralcd.cpp:2661
 msgid "Changed correctly?"
 msgstr "Wymiana ok?"
 
@@ -328,40 +348,45 @@ msgid "Changing filament!"
 msgstr "Wymiana filamentu!"
 
 # MSG_SELFTEST_CHECK_BED c=20
-#: messages.c:77
+#: messages.c:81
 msgid "Checking bed     "
 msgstr "Kontrola stolu"
 
 # MSG_SELFTEST_CHECK_ENDSTOPS c=20
-#: ultralcd.cpp:7450
+#: ultralcd.cpp:8200
 msgid "Checking endstops"
 msgstr "Kontrola krancowek"
 
 # MSG_SELFTEST_CHECK_HOTEND c=20
-#: ultralcd.cpp:7456
+#: ultralcd.cpp:8206
 msgid "Checking hotend  "
 msgstr "Kontrola hotendu"
 
 # MSG_SELFTEST_CHECK_FSENSOR c=20
-#: messages.c:78
+#: messages.c:82
 msgid "Checking sensors "
 msgstr "Sprawdzanie czujnikow"
 
 # MSG_SELFTEST_CHECK_X c=20
-#: ultralcd.cpp:7451
+#: ultralcd.cpp:8201
 msgid "Checking X axis  "
 msgstr "Kontrola osi X"
 
 # MSG_SELFTEST_CHECK_Y c=20
-#: ultralcd.cpp:7452
+#: ultralcd.cpp:8202
 msgid "Checking Y axis  "
 msgstr "Kontrola osi Y"
 
 # MSG_SELFTEST_CHECK_Z c=20
-#: ultralcd.cpp:7453
+#: ultralcd.cpp:8203
 msgid "Checking Z axis  "
 msgstr "Kontrola osi Z"
 
+# 
+#: ultralcd.cpp:5537
+msgid "Checks"
+msgstr "Testy"
+
 # MSG_ERR_CHECKSUM_MISMATCH
 #: cmdqueue.cpp:444
 msgid "checksum mismatch, Last Line: "
@@ -378,7 +403,7 @@ msgid "Choose filament:"
 msgstr "Wybierz filament:"
 
 # MSG_NOT_COLOR
-#: ultralcd.cpp:2563
+#: ultralcd.cpp:2673
 msgid "Color not correct"
 msgstr "Kolor zanieczysz."
 
@@ -393,12 +418,12 @@ msgid "Copy selected language from XFLASH?"
 msgstr "Skopiowac wybrany jezyk z XFLASH?"
 
 # 
-#: ultralcd.cpp:4360
+#: ultralcd.cpp:4499
 msgid "Copy selected language?"
 msgstr "Skopiowac wybrany jezyk?"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Crash"
 msgstr "Zderzenie"
 
@@ -423,22 +448,27 @@ msgid "Crash detected."
 msgstr "Zderzenie wykryte"
 
 # 
-#: Marlin_main.cpp:608
+#: Marlin_main.cpp:618
 msgid "Crash detected. Resume print?"
 msgstr "Wykryto zderzenie. Wznowic druk?"
 
+# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
+#:
+msgid "Crash detection can\nbe turned on only in\nNormal mode"
+msgstr "Wykrywanie zderzen\nmoze byc wlaczone tylko\nw trybie Normalnym"
+
 # MSG_CURRENT c=19 r=1
-#: ultralcd.cpp:5335
+#: ultralcd.cpp:5804
 msgid "Current"
 msgstr "Aktualne"
 
 # MSG_DATE c=17 r=1
-#: ultralcd.cpp:2235
+#: ultralcd.cpp:2106
 msgid "Date:"
 msgstr "Data:"
 
 # MSG_DISABLE_STEPPERS
-#: ultralcd.cpp:5093
+#: ultralcd.cpp:5552
 msgid "Disable steppers"
 msgstr "Wylaczenie silnikow"
 
@@ -448,7 +478,7 @@ msgid "Distance between tip of the nozzle and the bed surface has not been set y
 msgstr "Odleglosc dyszy od powierzchni druku nie jest skalibrowana. Postepuj zgodnie z instrukcja: rozdzial Wprowadzenie - Kalibracja pierwszej warstwy."
 
 # MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
-#: ultralcd.cpp:4828
+#: ultralcd.cpp:4968
 msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
 msgstr "Chcesz powtorzyc ostatni krok i ponownie ustawic odleglosc miedzy dysza a stolikiem?"
 
@@ -462,13 +492,18 @@ msgstr "Kalibracja E zakonczona. Oczysc dysze i potwierdz naciskajac pokretlo. "
 msgid "E-correct"
 msgstr "Korekcja E"
 
+# MSG_EXTRUDER_CORRECTION c=10
+#: ultralcd.cpp:5032
+msgid "E-correct:"
+msgstr "Korekcja-E:"
+
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Eject"
 msgstr "Wysun"
 
 # MSG_EJECT_FILAMENT c=17 r=1
-#: ultralcd.cpp:6081
+#: messages.c:53
 msgid "Eject filament"
 msgstr "Wysun filament"
 
@@ -498,7 +533,7 @@ msgid "Eject filament 5"
 msgstr "Wysun filament 5"
 
 # MSG_EJECTING_FILAMENT c=20 r=1
-#: mmu.cpp:1339
+#: mmu.cpp:1435
 msgid "Ejecting filament"
 msgstr "Wysuwanie filamentu"
 
@@ -508,17 +543,17 @@ msgid "End file list"
 msgstr "Koniec listy plikow"
 
 # MSG_SELFTEST_ENDSTOP
-#: ultralcd.cpp:7090
+#: ultralcd.cpp:7825
 msgid "Endstop"
 msgstr "Krancowka"
 
 # MSG_SELFTEST_ENDSTOP_NOTHIT c=20 r=1
-#: ultralcd.cpp:7096
+#: ultralcd.cpp:7831
 msgid "Endstop not hit"
 msgstr "Krancowka nie aktyw."
 
 # MSG_SELFTEST_ENDSTOPS
-#: ultralcd.cpp:7078
+#: ultralcd.cpp:7813
 msgid "Endstops"
 msgstr "Krancowki"
 
@@ -538,7 +573,7 @@ msgid "enqueing \""
 msgstr "kolejkowanie \""
 
 # MSG_STACK_ERROR c=20 r=4
-#: ultralcd.cpp:6132
+#: ultralcd.cpp:6773
 msgid "Error - static memory has been overwritten"
 msgstr "Blad - pamiec statyczna zostala nadpisana"
 
@@ -553,7 +588,7 @@ msgid "ERROR:"
 msgstr "BLAD:"
 
 # MSG_FSENS_NOT_RESPONDING c=20 r=4
-#: ultralcd.cpp:4259
+#: ultralcd.cpp:4388
 msgid "ERROR: Filament sensor is not responding, please check connection."
 msgstr "BLAD: Czujnik filamentu nie odpowiada, sprawdz polaczenie."
 
@@ -588,17 +623,17 @@ msgid "Extruder 4"
 msgstr "Ekstruder 4"
 
 # MSG_SELFTEST_EXTRUDER_FAN_SPEED c=18
-#: ultralcd.cpp:7468
+#: ultralcd.cpp:8218
 msgid "Extruder fan:"
 msgstr "Went. ekstrudera:"
 
 # MSG_INFO_EXTRUDER c=15 r=1
-#: ultralcd.cpp:2266
+#: ultralcd.cpp:2137
 msgid "Extruder info"
 msgstr "Informacje o ekstruderze"
 
 # MSG_FSENS_AUTOLOAD_ON c=17 r=1
-#: ultralcd.cpp:4927
+#: ultralcd.cpp:5066
 msgid "F. autoload  [on]"
 msgstr "Autolad. fil [wl]"
 
@@ -608,37 +643,42 @@ msgid "F. autoload [N/A]"
 msgstr "Autolad.fil.[N/D]"
 
 # MSG_FSENS_AUTOLOAD_OFF c=17 r=1
-#: ultralcd.cpp:4929
+#: ultralcd.cpp:5068
 msgid "F. autoload [off]"
 msgstr "Autolad.fil.[wyl]"
 
 # 
-#: ultralcd.cpp:6112
+#: ultralcd.cpp:6757
 msgid "Fail stats"
 msgstr "Statystyki bledow"
 
 # 
-#: ultralcd.cpp:6115
+#: ultralcd.cpp:6760
 msgid "Fail stats MMU"
 msgstr "Bledy MMU"
 
+# 
+#: ultralcd.cpp:7887
+msgid "False triggering"
+msgstr "Falszywy alarm"
+
 # MSG_FAN_SPEED c=14
 #: messages.c:31
 msgid "Fan speed"
 msgstr "Predkosc went."
 
 # MSG_SELFTEST_FAN c=20
-#: messages.c:74
+#: messages.c:78
 msgid "Fan test"
 msgstr "Test wentylatora"
 
 # MSG_FANS_CHECK_ON c=17 r=1
-#: ultralcd.cpp:5100
+#: ultralcd.cpp:5561
 msgid "Fans check   [on]"
 msgstr "Sprawd.went. [wl]"
 
 # MSG_FANS_CHECK_OFF c=17 r=1
-#: ultralcd.cpp:5102
+#: ultralcd.cpp:5563
 msgid "Fans check  [off]"
 msgstr "Sprawd.went.[wyl]"
 
@@ -653,7 +693,7 @@ msgid "Fil. sensor response is poor, disable it?"
 msgstr "Reakcja czujnika slaba, wylaczyc?"
 
 # MSG_FSENSOR_NA
-#: ultralcd.cpp:4907
+#: ultralcd.cpp:5046
 msgid "Fil. sensor [N/A]"
 msgstr "Czuj. filam.[N/D]"
 
@@ -663,7 +703,7 @@ msgid "Fil. sensor [off]"
 msgstr "Czuj. filam.[wyl]"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Filam. runouts"
 msgstr "Konc. filamentu"
 
@@ -678,12 +718,12 @@ msgid "Filament extruding & with correct color?"
 msgstr "Filament wychodzi z dyszy a kolor jest czysty?"
 
 # MSG_NOT_LOADED c=19
-#: ultralcd.cpp:2559
+#: ultralcd.cpp:2669
 msgid "Filament not loaded"
 msgstr "Fil. nie zaladowany"
 
 # MSG_FILAMENT_SENSOR c=20
-#: ultralcd.cpp:7144
+#: messages.c:84
 msgid "Filament sensor"
 msgstr "Czujnik filamentu"
 
@@ -693,7 +733,7 @@ msgid "Filament sensor:"
 msgstr "Czujnik filamentu:"
 
 # MSG_FILAMENT_USED c=19 r=1
-#: ultralcd.cpp:2725
+#: ultralcd.cpp:2838
 msgid "Filament used"
 msgstr "Uzyty filament"
 
@@ -703,7 +743,7 @@ msgid "Filament used:  "
 msgstr "Uzywany filament:"
 
 # MSG_FILE_INCOMPLETE c=20 r=2
-#: ultralcd.cpp:7595
+#: ultralcd.cpp:8346
 msgid "File incomplete. Continue anyway?"
 msgstr "Plik niekompletny. Kontynowac?"
 
@@ -717,53 +757,103 @@ msgstr "Otwarty plik:"
 msgid "File selected"
 msgstr "Wybrano plik"
 
+# 
+#: ultralcd.cpp:3943
+msgid "FINDA:"
+msgstr "FINDA:"
+
 # MSG_FINISHING_MOVEMENTS c=20 r=1
 #: messages.c:40
 msgid "Finishing movements"
 msgstr "Konczenie druku"
 
+# 
+#: ultralcd.cpp:5443
+msgid "Firmware   [none]"
+msgstr "Firmware [brak]"
+
+# 
+#: ultralcd.cpp:5446
+msgid "Firmware   [warn]"
+msgstr "Firmware [ostrzez.]"
+
+# 
+#: ultralcd.cpp:5449
+msgid "Firmware [strict]"
+msgstr "Firmware [restr.]"
+
 # MSG_V2_CALIBRATION c=17 r=1
-#: ultralcd.cpp:5177
+#: messages.c:105
 msgid "First layer cal."
 msgstr "Kal. 1. warstwy"
 
 # MSG_WIZARD_SELFTEST c=20 r=8
-#: ultralcd.cpp:4740
+#: ultralcd.cpp:4880
 msgid "First, I will run the selftest to check most common assembly problems."
 msgstr "Najpierw wlacze selftest w celu sprawdzenia najczestszych problemow podczas montazu."
 
 # 
-#: mmu.cpp:640
+#: mmu.cpp:724
 msgid "Fix the issue and then press button on MMU unit."
 msgstr "Rozwiaz problem i wcisnij przycisk na MMU."
 
 # MSG_FLOW
-#: ultralcd.cpp:6205
+#: ultralcd.cpp:6846
 msgid "Flow"
 msgstr "Przeplyw"
 
 # MSG_PRUSA3D_FORUM
-#: ultralcd.cpp:2228
+#: ultralcd.cpp:2099
 msgid "forum.prusa3d.com"
 msgstr "forum.prusa3d.com"
 
 # MSG_SELFTEST_COOLING_FAN c=20
-#: messages.c:71
+#: messages.c:75
 msgid "Front print fan?"
 msgstr "Przedni went. druku?"
 
 # MSG_BED_CORRECTION_FRONT c=14 r=1
-#: ultralcd.cpp:3101
+#: ultralcd.cpp:3217
 msgid "Front side[um]"
 msgstr "Przod [um]"
 
 # MSG_SELFTEST_FANS
-#: ultralcd.cpp:7136
+#: ultralcd.cpp:7871
 msgid "Front/left fans"
 msgstr "Przedni/lewy wentylator"
 
+# 
+#: util.cpp:510
+msgid "G-code sliced for a different level. Continue?"
+msgstr "G-code pociety na innym poziomie. Kontynuowac?"
+
+# 
+#: util.cpp:516
+msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
+msgstr "G-code pociety na innym poziomie. Potnij model ponownie. Druk anulowany."
+
+# 
+#: util.cpp:427
+msgid "G-code sliced for a different printer type. Continue?"
+msgstr "G-code pociety dla innej drukarki. Kontynuowac?"
+
+# 
+#: util.cpp:433
+msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
+msgstr "G-code pociety dla drukarki innego typu. Potnij model ponownie. Druk anulowany."
+
+# 
+#: util.cpp:477
+msgid "G-code sliced for a newer firmware. Continue?"
+msgstr "G-code pociety dla nowszego firmware. Kontynuowac?"
+
+# 
+#: util.cpp:483
+msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
+msgstr "G-code pociety dla nowszego firmware. Zaktualizuj firmware. Druk anulowany."
+
 # MSG_SELFTEST_HEATERTHERMISTOR
-#: ultralcd.cpp:7066
+#: ultralcd.cpp:7801
 msgid "Heater/Thermistor"
 msgstr "Grzalka/Termistor"
 
@@ -773,7 +863,7 @@ msgid "Heating"
 msgstr "Grzanie..."
 
 # MSG_BED_HEATING_SAFETY_DISABLED
-#: Marlin_main.cpp:7475
+#: Marlin_main.cpp:8411
 msgid "Heating disabled by safety timer."
 msgstr "Grzanie wylaczone przez wyl. czasowy"
 
@@ -783,27 +873,32 @@ msgid "Heating done."
 msgstr "Grzanie zakonczone"
 
 # MSG_WIZARD_WELCOME c=20 r=7
-#: ultralcd.cpp:4719
+#: ultralcd.cpp:4859
 msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
 msgstr "Czesc, jestem Twoja drukarka Original Prusa i3. Czy potrzebujesz pomocy z ustawieniem?"
 
 # MSG_PRUSA3D_HOWTO
-#: ultralcd.cpp:2229
+#: ultralcd.cpp:2100
 msgid "howto.prusa3d.com"
 msgstr "howto.prusa3d.com"
 
+# 
+#: messages.c:87
+msgid "HW Setup"
+msgstr "Ustawienia HW"
+
 # MSG_WIZARD_XYZ_CAL c=20 r=8
-#: ultralcd.cpp:4749
+#: ultralcd.cpp:4889
 msgid "I will run xyz calibration now. It will take approx. 12 mins."
 msgstr "Przeprowadze teraz kalibracje XYZ. Zajmie ok. 12 min."
 
 # MSG_WIZARD_Z_CAL c=20 r=8
-#: ultralcd.cpp:4757
+#: ultralcd.cpp:4897
 msgid "I will run z calibration now."
 msgstr "Przeprowadze kalibracje Z."
 
 # MSG_WIZARD_V2_CAL_2 c=20 r=12
-#: ultralcd.cpp:4822
+#: ultralcd.cpp:4962
 msgid "I will start to print line and you will gradually lower the nozzle by rotating the knob, until you reach optimal height. Check the pictures in our handbook in chapter Calibration."
 msgstr "Zaczne drukowac linie. Stopniowo opuszczaj dysze przekrecajac pokretlo, poki nie uzyskasz optymalnej wysokosci. Sprawdz obrazki w naszym Podreczniku w rozdz. Kalibracja"
 
@@ -813,7 +908,7 @@ msgid "Improving bed calibration point"
 msgstr "Poprawiam precyzje punktu kalibracyjnego"
 
 # MSG_WATCH
-#: messages.c:93
+#: messages.c:99
 msgid "Info screen"
 msgstr "Ekran informacyjny"
 
@@ -823,7 +918,7 @@ msgid "Init. SD card"
 msgstr "Inicjalizacja karty SD"
 
 # MSG_INSERT_FILAMENT c=20
-#: ultralcd.cpp:2459
+#: ultralcd.cpp:2569
 msgid "Insert filament"
 msgstr "Wprowadz filament"
 
@@ -848,27 +943,32 @@ msgid "Insert filament into extruder 4. Click when done."
 msgstr "Wloz filament do ekstrudera 4. Potwierdz naciskajac pokretlo."
 
 # 
-#: ultralcd.cpp:4782
+#: ultralcd.cpp:3947
+msgid "IR:"
+msgstr "IR:"
+
+# 
+#: ultralcd.cpp:4922
 msgid "Is filament 1 loaded?"
 msgstr "Filament 1 zaladowany?"
 
 # MSG_WIZARD_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4785
+#: ultralcd.cpp:4925
 msgid "Is filament loaded?"
 msgstr "Filament jest zaladowany?"
 
 # MSG_WIZARD_PLA_FILAMENT c=20 r=2
-#: ultralcd.cpp:4816
+#: ultralcd.cpp:4956
 msgid "Is it PLA filament?"
 msgstr "Czy to filament PLA?"
 
 # MSG_PLA_FILAMENT_LOADED c=20 r=2
-#: ultralcd.cpp:4561
+#: ultralcd.cpp:4701
 msgid "Is PLA filament loaded?"
 msgstr "Fialment PLA jest zaladowany?"
 
 # MSG_STEEL_SHEET_CHECK c=20 r=2
-#: messages.c:86
+#: messages.c:92
 msgid "Is steel sheet on heatbed?"
 msgstr "Czy plyta stal. jest na podgrzew. stole?"
 
@@ -883,27 +983,27 @@ msgid "KILLED. "
 msgstr "PRZERWANE."
 
 # 
-#: ultralcd.cpp:1960
+#: ultralcd.cpp:1828
 msgid "Last print"
 msgstr "Ost. wydruk"
 
 # 
-#: ultralcd.cpp:1976
+#: ultralcd.cpp:1845
 msgid "Last print failures"
 msgstr "Ostatnie bledy druku"
 
 # 
-#: ultralcd.cpp:2861
+#: ultralcd.cpp:2967
 msgid "Left"
 msgstr "Lewa"
 
 # MSG_SELFTEST_EXTRUDER_FAN c=20
-#: messages.c:72
+#: messages.c:76
 msgid "Left hotend fan?"
 msgstr "Lewy went hotendu?"
 
 # MSG_BED_CORRECTION_LEFT c=14 r=1
-#: ultralcd.cpp:3099
+#: ultralcd.cpp:3215
 msgid "Left side [um]"
 msgstr "Lewo [um]"
 
@@ -913,7 +1013,7 @@ msgid "Left:"
 msgstr "Lewo:"
 
 # 
-#: ultralcd.cpp:5107
+#: ultralcd.cpp:5575
 msgid "Lin. correction"
 msgstr "Korekcja lin."
 
@@ -923,7 +1023,7 @@ msgid "Live adjust Z"
 msgstr "Ustaw. Live Z"
 
 # MSG_LOAD_ALL c=17
-#: ultralcd.cpp:5575
+#: ultralcd.cpp:6059
 msgid "Load all"
 msgstr "Zalad. wszystkie"
 
@@ -958,12 +1058,12 @@ msgid "Load filament 5"
 msgstr "Laduj filament 5"
 
 # 
-#: ultralcd.cpp:6079
+#: ultralcd.cpp:6714
 msgid "Load to nozzle"
 msgstr "Zaladuj do dyszy"
 
 # MSG_LOADING_COLOR
-#: ultralcd.cpp:2499
+#: ultralcd.cpp:2609
 msgid "Loading color"
 msgstr "Czyszcz. koloru"
 
@@ -973,7 +1073,7 @@ msgid "Loading filament"
 msgstr "Laduje filament"
 
 # MSG_LOOSE_PULLEY c=20 r=1
-#: ultralcd.cpp:7120
+#: ultralcd.cpp:7855
 msgid "Loose pulley"
 msgstr "Luzne kolo pasowe"
 
@@ -993,7 +1093,7 @@ msgid "M109 Invalid extruder "
 msgstr "M109 Nieprawidlowy ekstruder"
 
 # MSG_M117_V2_CALIBRATION c=25 r=1
-#: messages.c:53
+#: messages.c:55
 msgid "M117 First layer cal."
 msgstr "M117 Kal. 1. warstwy"
 
@@ -1012,8 +1112,23 @@ msgstr "M218 Nieprawidlowy ekstruder"
 msgid "M221 Invalid extruder "
 msgstr "M221 Nieprawidlowy ekstruder"
 
+# 
+#: ultralcd.cpp:6957
+msgid "Magnets comp. [On]"
+msgstr "Kor. magnesow[wl]"
+
+# 
+#: ultralcd.cpp:6960
+msgid "Magnets comp.[N/A]"
+msgstr "Kor. magnesow[nd]"
+
+# 
+#: ultralcd.cpp:6958
+msgid "Magnets comp.[Off]"
+msgstr "Kor. magnesow[wyl]"
+
 # MSG_MAIN
-#: messages.c:54
+#: messages.c:56
 msgid "Main"
 msgstr "Menu glowne"
 
@@ -1023,7 +1138,7 @@ msgid "Mark filament 100mm from extruder body. Click when done."
 msgstr "Zaznacz filament na wysokosci 100 mm od korpusu ekstrudera i potwierdz naciskajac pokretlo."
 
 # 
-#: ultralcd.cpp:2896
+#: ultralcd.cpp:3002
 msgid "Measured skew"
 msgstr "Zmierzony skos"
 
@@ -1033,32 +1148,67 @@ msgid "Measured skew:"
 msgstr "Zmierzony skos:"
 
 # MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=60
-#: messages.c:55
+#: messages.c:59
 msgid "Measuring reference height of calibration point"
 msgstr "Okreslam wysokosc odniesienia punktu kalibracyjnego"
 
+# 
+#: ultralcd.cpp:6949
+msgid "Mesh         [3x3]"
+msgstr "Siatka [3x3]"
+
+# 
+#: ultralcd.cpp:6950
+msgid "Mesh         [7x7]"
+msgstr "Siatka [7x7]"
+
 # MSG_MESH_BED_LEVELING
-#: ultralcd.cpp:5192
+#: ultralcd.cpp:5658
 msgid "Mesh Bed Leveling"
 msgstr "Poziomowanie stolu wg siatki"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:5572
+msgid "Mesh bed leveling"
+msgstr "Poziomowanie wg siatki"
+
+# 
+#: Marlin_main.cpp:881
+msgid "MK3 firmware detected on MK3S printer"
+msgstr "Wykryto firmware MK3 w drukarce MK3S"
+
+# 
+#: Marlin_main.cpp:856
+msgid "MK3S firmware detected on MK3 printer"
+msgstr "Wykryto firmware MK3S w drukarce MK3"
+
+# 
+#: ultralcd.cpp:1845
 msgid "MMU fails"
 msgstr "Bledy MMU"
 
 # 
-#: mmu.cpp:1399
+#: mmu.cpp:1617
 msgid "MMU load failed     "
 msgstr "Blad ladowania MMU"
 
 # 
-#: ultralcd.cpp:1977
+#: ultralcd.cpp:1845
 msgid "MMU load fails"
 msgstr "Bledy ladow. MMU"
 
 # 
-#: mmu.cpp:635
+#: ultralcd.cpp:5204
+msgid "MMU Mode [Normal]"
+msgstr "Tryb MMU [Normalny]"
+
+# 
+#: ultralcd.cpp:5205
+msgid "MMU Mode[Stealth]"
+msgstr "Tryb MMU [Stealth]"
+
+# 
+#: mmu.cpp:719
 msgid "MMU needs user attention."
 msgstr "MMU wymaga uwagi uzytkownika."
 
@@ -1068,82 +1218,102 @@ msgid "MMU needs user attention. Fix the issue and then press button on MMU unit
 msgstr "MMU wymaga uwagi. Napraw usterke i wcisnij przycisk na korpusie MMU."
 
 # MSG_MMU_OK_RESUMING_POSITION c=20 r=4
-#: mmu.cpp:676
+#: mmu.cpp:762
 msgid "MMU OK. Resuming position..."
 msgstr "MMU OK. Wznawianie pozycji."
 
 # MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
-#: mmu.cpp:669
+#: mmu.cpp:755
 msgid "MMU OK. Resuming temperature..."
 msgstr "MMU OK. Wznawiam nagrzewanie..."
 
 # MSG_MMU_OK_RESUMING c=20 r=4
-#: mmu.cpp:687
+#: mmu.cpp:773
 msgid "MMU OK. Resuming..."
 msgstr "MMU OK. Wznawianie..."
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "MMU power fails"
 msgstr "Zaniki zasil. MMU"
 
 # 
-#: ultralcd.cpp:2241
+#: ultralcd.cpp:2112
 msgid "MMU2 connected"
 msgstr "MMU podlaczone"
 
 # MSG_STEALTH_MODE_OFF
-#: messages.c:84
+#: messages.c:90
 msgid "Mode     [Normal]"
 msgstr "Tryb   [normalny]"
 
 # MSG_SILENT_MODE_ON
-#: messages.c:83
+#: messages.c:89
 msgid "Mode     [silent]"
 msgstr "Tryb      [cichy]"
 
 # MSG_STEALTH_MODE_ON
-#: messages.c:85
+#: messages.c:91
 msgid "Mode    [Stealth]"
 msgstr "Tryb    [Stealth]"
 
+# 
+#: ultralcd.cpp:4424
+msgid "Mode change in progress ..."
+msgstr "Trwa zmiana trybu..."
+
 # MSG_AUTO_MODE_ON
 #: messages.c:12
 msgid "Mode [auto power]"
 msgstr "Tryb [automatycz]"
 
 # MSG_SILENT_MODE_OFF
-#: messages.c:82
+#: messages.c:88
 msgid "Mode [high power]"
 msgstr "Tryb[wysoka wyd.]"
 
+# 
+#: ultralcd.cpp:5404
+msgid "Model      [none]"
+msgstr "Model [brak]"
+
+# 
+#: ultralcd.cpp:5407
+msgid "Model      [warn]"
+msgstr "Model [ostrzez.]"
+
+# 
+#: ultralcd.cpp:5410
+msgid "Model    [strict]"
+msgstr "Model [restrykc.]"
+
 # MSG_SELFTEST_MOTOR
-#: messages.c:79
+#: messages.c:83
 msgid "Motor"
 msgstr "Silnik"
 
 # MSG_MOVE_AXIS
-#: ultralcd.cpp:5091
+#: ultralcd.cpp:5550
 msgid "Move axis"
 msgstr "Ruch osi"
 
 # MSG_MOVE_X
-#: ultralcd.cpp:4164
+#: ultralcd.cpp:4291
 msgid "Move X"
 msgstr "Ruch osi X"
 
 # MSG_MOVE_Y
-#: ultralcd.cpp:4165
+#: ultralcd.cpp:4292
 msgid "Move Y"
 msgstr "Ruch osi Y"
 
 # MSG_MOVE_Z
-#: ultralcd.cpp:4166
+#: ultralcd.cpp:4293
 msgid "Move Z"
 msgstr "Ruch osi Z"
 
 # 
-#: ultralcd.cpp:2867
+#: ultralcd.cpp:2973
 msgid "N/A"
 msgstr "N/D"
 
@@ -1153,7 +1323,7 @@ msgid "New firmware version available:"
 msgstr "Dostepna nowa wersja firmware:"
 
 # MSG_NO
-#: messages.c:58
+#: messages.c:62
 msgid "No"
 msgstr "Nie"
 
@@ -1168,12 +1338,12 @@ msgid "No Checksum with line number, Last Line: "
 msgstr "Brak sumy kontrolnej z numerem linii, ostatnia linia:"
 
 # MSG_NO_MOVE
-#: Marlin_main.cpp:4908
+#: Marlin_main.cpp:5254
 msgid "No move."
 msgstr "Brak ruchu."
 
 # MSG_NO_CARD
-#: ultralcd.cpp:6059
+#: ultralcd.cpp:6694
 msgid "No SD card"
 msgstr "Brak karty SD"
 
@@ -1183,37 +1353,67 @@ msgid "No thermistors - no temperature"
 msgstr "Brak termistorow - brak odczytu temperatury"
 
 # MSG_SELFTEST_NOTCONNECTED
-#: ultralcd.cpp:7068
+#: ultralcd.cpp:7803
 msgid "Not connected"
 msgstr "Nie podlaczono "
 
 # MSG_SELFTEST_FAN_NO c=19
-#: messages.c:75
+#: messages.c:79
 msgid "Not spinning"
 msgstr "Nie kreci sie"
 
 # MSG_WIZARD_V2_CAL c=20 r=8
-#: ultralcd.cpp:4821
+#: ultralcd.cpp:4961
 msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
 msgstr "Kalibruje odleglosc miedzy koncowka dyszy a powierzchnia druku."
 
 # MSG_WIZARD_WILL_PREHEAT c=20 r=4
-#: ultralcd.cpp:4765
+#: ultralcd.cpp:4905
 msgid "Now I will preheat nozzle for PLA."
 msgstr "Nagrzewam dysze dla PLA."
 
 # 
-#: ultralcd.cpp:4756
+#: ultralcd.cpp:4896
 msgid "Now remove the test print from steel sheet."
 msgstr "Teraz zdejmij wydruk testowy ze stolu."
 
 # MSG_NOZZLE
-#: messages.c:59
+#: messages.c:63
 msgid "Nozzle"
 msgstr "Dysza"
 
 # 
-#: ultralcd.cpp:1919
+#: ultralcd.cpp:5319
+msgid "Nozzle     [none]"
+msgstr "Dysza [brak]"
+
+# 
+#: ultralcd.cpp:5322
+msgid "Nozzle     [warn]"
+msgstr "Dysza [ostrzez.]"
+
+# 
+#: ultralcd.cpp:5325
+msgid "Nozzle   [strict]"
+msgstr "Dysza [restrykc.]"
+
+# 
+#: ultralcd.cpp:5365
+msgid "Nozzle d.  [0.25]"
+msgstr "Sr. dyszy [0,25]"
+
+# 
+#: ultralcd.cpp:5368
+msgid "Nozzle d.  [0.40]"
+msgstr "Sr. dyszy [0,40]"
+
+# 
+#: ultralcd.cpp:5371
+msgid "Nozzle d.  [0.60]"
+msgstr "Sr. dyszy [0,60]"
+
+# 
+#: ultralcd.cpp:1787
 msgid "Nozzle FAN"
 msgstr "Went. hotendu"
 
@@ -1238,7 +1438,7 @@ msgid "ok"
 msgstr "ok"
 
 # MSG_DEFAULT_SETTINGS_LOADED c=20 r=4
-#: Marlin_main.cpp:1516
+#: Marlin_main.cpp:1535
 msgid "Old settings found. Default PID, Esteps etc. will be set."
 msgstr "Znaleziono stare ustawienia. Zostana przywrocone domyslne ust. PID, Esteps, itp."
 
@@ -1258,7 +1458,7 @@ msgid "openRoot failed"
 msgstr "niepowodzenie openRoot "
 
 # MSG_PAUSE_PRINT
-#: ultralcd.cpp:6029
+#: ultralcd.cpp:6657
 msgid "Pause print"
 msgstr "Wstrzymanie wydruku"
 
@@ -1268,42 +1468,47 @@ msgid "Pick print"
 msgstr "Wybierz wydruk"
 
 # MSG_PID_RUNNING c=20 r=1
-#: ultralcd.cpp:1741
+#: ultralcd.cpp:1613
 msgid "PID cal.           "
 msgstr "Kalibracja PID"
 
 # MSG_PID_FINISHED c=20 r=1
-#: ultralcd.cpp:1747
+#: ultralcd.cpp:1619
 msgid "PID cal. finished"
 msgstr "Kal. PID zakonczona"
 
 # MSG_PID_EXTRUDER c=17 r=1
-#: ultralcd.cpp:5198
+#: ultralcd.cpp:5664
 msgid "PID calibration"
 msgstr "Kalibracja PID"
 
 # MSG_PINDA_PREHEAT c=20 r=1
-#: ultralcd.cpp:808
+#: ultralcd.cpp:862
 msgid "PINDA Heating"
 msgstr "Grzanie sondy PINDA"
 
+# 
+#: ultralcd.cpp:3939
+msgid "PINDA:"
+msgstr "PINDA:"
+
 # MSG_PAPER c=20 r=8
-#: messages.c:60
+#: messages.c:64
 msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
 msgstr "Umiesc kartke papieru na stole roboczym i podczas pomiaru pierwszych 4 punktow. Jesli dysza zahaczy o papier, natychmiast wylacz drukarke."
 
 # MSG_SELFTEST_PLEASECHECK
-#: ultralcd.cpp:7060
+#: ultralcd.cpp:7795
 msgid "Please check :"
 msgstr "Sprawdz :"
 
 # MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
-#: messages.c:94
+#: messages.c:100
 msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
 msgstr "Przeczytaj nasz Podrecznik druku 3D aby naprawic problem. Potem wznow Asystenta przez restart drukarki."
 
 # MSG_WIZARD_CLEAN_HEATBED c=20 r=8
-#: ultralcd.cpp:4830
+#: ultralcd.cpp:4970
 msgid "Please clean heatbed and then press the knob."
 msgstr "Oczysc powierzchnie druku i nacisnij pokretlo."
 
@@ -1313,12 +1518,12 @@ msgid "Please clean the nozzle for calibration. Click when done."
 msgstr "Dla prawidl. kalibracji nalezy oczyscic dysze. Potw. guzikiem."
 
 # MSG_WIZARD_LOAD_FILAMENT c=20 r=8
-#: ultralcd.cpp:4664
+#: ultralcd.cpp:4804
 msgid "Please insert PLA filament to the extruder, then press knob to load it."
 msgstr "Umiesc filament PLA w ekstruderze i nacisnij pokretlo, aby zaladowac."
 
 # 
-#: ultralcd.cpp:4660
+#: ultralcd.cpp:4800
 msgid "Please insert PLA filament to the first tube of MMU, then press the knob to load it."
 msgstr "Wsun filament PLA do pierwszej rurki MMU i nacisnij pokretlo aby go zaladowac."
 
@@ -1328,52 +1533,52 @@ msgid "Please load PLA filament and then resume Wizard by rebooting the printer.
 msgstr "Zaladuj filament PLA i przywroc Asystenta przez restart drukarki."
 
 # MSG_PLEASE_LOAD_PLA c=20 r=4
-#: ultralcd.cpp:4566
+#: ultralcd.cpp:4706
 msgid "Please load PLA filament first."
 msgstr "Najpierw zaladuj filament PLA."
 
 # MSG_CHECK_IDLER c=20 r=4
-#: Marlin_main.cpp:3025
+#: Marlin_main.cpp:3083
 msgid "Please open idler and remove filament manually."
 msgstr "Prosze odciagnac dzwignie dociskowa ekstrudera i recznie usunac filament."
 
 # MSG_PLACE_STEEL_SHEET c=20 r=4
-#: messages.c:61
+#: messages.c:65
 msgid "Please place steel sheet on heatbed."
 msgstr "Prosze umiescic plyte stalowa na stole podgrzewanym."
 
 # MSG_PRESS_TO_UNLOAD c=20 r=4
-#: messages.c:64
+#: messages.c:68
 msgid "Please press the knob to unload filament"
 msgstr "Nacisnij pokretlo aby rozladowac filament"
 
 # MSG_PULL_OUT_FILAMENT c=20 r=4
-#: messages.c:66
+#: messages.c:70
 msgid "Please pull out filament immediately"
 msgstr "Wyciagnij filament teraz"
 
 # MSG_EJECT_REMOVE c=20 r=4
-#: mmu.cpp:1347
+#: mmu.cpp:1441
 msgid "Please remove filament and then press the knob."
 msgstr "Wyciagnij filament i wcisnij pokretlo."
 
 # 
-#: ultralcd.cpp:4755
+#: ultralcd.cpp:4895
 msgid "Please remove shipping helpers first."
 msgstr "Najpierw usun zabezpieczenia transportowe"
 
 # MSG_REMOVE_STEEL_SHEET c=20 r=4
-#: messages.c:70
+#: messages.c:74
 msgid "Please remove steel sheet from heatbed."
 msgstr "Prosze zdjac plyte stalowa z podgrzewanego stolu."
 
 # MSG_RUN_XYZ c=20 r=4
-#: Marlin_main.cpp:4052
+#: Marlin_main.cpp:4317
 msgid "Please run XYZ calibration first."
 msgstr "Prosze najpierw uruchomic kalibracje XYZ"
 
 # MSG_UPDATE_MMU2_FW c=20 r=4
-#: mmu.cpp:1293
+#: mmu.cpp:1360
 msgid "Please update firmware in your MMU2. Waiting for reset."
 msgstr "Prosze zaktualizowac Firmware MMU2. Czekam na reset."
 
@@ -1383,12 +1588,12 @@ msgid "Please upgrade."
 msgstr "Prosze zaktualizowac."
 
 # MSG_PLEASE_WAIT c=20
-#: messages.c:62
+#: messages.c:66
 msgid "Please wait"
 msgstr "Prosze czekac"
 
 # 
-#: ultralcd.cpp:2013
+#: ultralcd.cpp:1881
 msgid "Power failures"
 msgstr "Zaniki zasilania"
 
@@ -1398,27 +1603,37 @@ msgid "PowerUp"
 msgstr "Uruchamianie"
 
 # MSG_PREHEAT
-#: ultralcd.cpp:6018
+#: ultralcd.cpp:6644
 msgid "Preheat"
 msgstr "Grzanie"
 
 # MSG_PREHEAT_NOZZLE c=20
-#: messages.c:63
+#: messages.c:67
 msgid "Preheat the nozzle!"
 msgstr "Nagrzej dysze!"
 
 # MSG_WIZARD_HEATING c=20 r=3
-#: messages.c:96
+#: messages.c:102
 msgid "Preheating nozzle. Please wait."
 msgstr "Nagrzewanie dyszy. Prosze czekac."
 
 # 
-#: ultralcd.cpp:2350
+#: ultralcd.cpp:2290
+msgid "Preheating to cut"
+msgstr "Nagrzewanie do obciecia"
+
+# 
+#: ultralcd.cpp:2287
+msgid "Preheating to eject"
+msgstr "Nagrzewanie do wysuniecia"
+
+# 
+#: ultralcd.cpp:2280
 msgid "Preheating to load"
 msgstr "Nagrzew. do ladowania"
 
 # 
-#: ultralcd.cpp:2351
+#: ultralcd.cpp:2284
 msgid "Preheating to unload"
 msgstr "Nagrzew. do rozlad."
 
@@ -1428,27 +1643,27 @@ msgid "Prepare new filament"
 msgstr "Przygotuj filament"
 
 # MSG_PRESS_TO_PREHEAT c=20 r=4
-#: Marlin_main.cpp:9150
+#: Marlin_main.cpp:10312
 msgid "Press knob to preheat nozzle and continue."
 msgstr "Wcisnij pokretlo aby rozgrzac dysze i kontynuowac."
 
 # 
-#: ultralcd.cpp:2313
+#: ultralcd.cpp:2210
 msgid "Press the knob"
 msgstr "Wcisnij pokretlo"
 
 # 
-#: mmu.cpp:639
+#: mmu.cpp:723
 msgid "Press the knob to resume nozzle temperature."
 msgstr "Wcisnij pokretlo aby wznowic podgrzewanie dyszy."
 
 # MSG_PRINT_ABORTED c=20
-#: messages.c:65
+#: messages.c:69
 msgid "Print aborted"
 msgstr "Druk przerwany"
 
 # 
-#: ultralcd.cpp:1921
+#: ultralcd.cpp:1789
 msgid "Print FAN"
 msgstr "Went. wydruku"
 
@@ -1458,7 +1673,7 @@ msgid "Print FAN: "
 msgstr "Went. wydr:"
 
 # MSG_SELFTEST_PRINT_FAN_SPEED c=18
-#: ultralcd.cpp:7471
+#: ultralcd.cpp:8221
 msgid "Print fan:"
 msgstr "Went. wydruku:"
 
@@ -1468,12 +1683,12 @@ msgid "Print from SD"
 msgstr "Druk z karty SD"
 
 # MSG_PRINT_PAUSED c=20 r=1
-#: ultralcd.cpp:1022
+#: ultralcd.cpp:1080
 msgid "Print paused"
 msgstr "Druk wstrzymany"
 
 # MSG_PRINT_TIME c=19 r=1
-#: ultralcd.cpp:2727
+#: ultralcd.cpp:2838
 msgid "Print time"
 msgstr "Czas druku"
 
@@ -1487,6 +1702,26 @@ msgstr "Czas druku: "
 msgid "Printer disconnected"
 msgstr "Drukarka rozlaczona"
 
+# 
+#: util.cpp:473
+msgid "Printer FW version differs from the G-code. Continue?"
+msgstr "Wersja FW drukarki rozni sie w G-code. Kontynuowac?"
+
+# 
+#: util.cpp:480
+msgid "Printer FW version differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "FW drukarki rozni sie od tego w G-code. Sprawdz ustawienia. Druk anulowany."
+
+# 
+#: util.cpp:506
+msgid "Printer G-code level differs from the G-code. Continue?"
+msgstr "Poziom G-code drukarki rozni sie od pliku G-code. Kontynuowac?"
+
+# 
+#: util.cpp:513
+msgid "Printer G-code level differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Poziom G-code drukarki rozni sie od pliku G-code. Sprawdz ustawienia. Druk anulowany"
+
 # MSG_ERR_KILLED
 #: Marlin_main.cpp:7547
 msgid "Printer halted. kill() called!"
@@ -1497,6 +1732,26 @@ msgstr "Drukarka zatrzymana. Wywolano komende kill()!"
 msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
 msgstr "Drukarka nie zostala jeszcze skalibrowana. Kieruj sie Samouczkiem: rozdzial Pierwsze Kroki, sekcja Konfiguracja przed drukowaniem."
 
+# 
+#: util.cpp:423
+msgid "Printer model differs from the G-code. Continue?"
+msgstr "Model drukarki rozni sie od tego w G-code. Kontynuowac?"
+
+# 
+#: util.cpp:430
+msgid "Printer model differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Model drukarki rozni sie od tego w G-code. Sprawdz ustawienia. Druk anulowany."
+
+# 
+#: util.cpp:390
+msgid "Printer nozzle diameter differs from the G-code. Continue?"
+msgstr "Srednica dyszy drukarki rozni sie od tej w G-code. Kontynuowac?"
+
+# 
+#: util.cpp:397
+msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
+msgstr "Srednica dyszy rozni sie od tej w G-code. Sprawdz ustawienia. Druk anulowany."
+
 # MSG_ERR_STOPPED
 #: messages.c:32
 msgid "Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
@@ -1512,6 +1767,11 @@ msgstr "Prusa i3 MK2 gotowa"
 msgid "Prusa i3 MK2.5 ready."
 msgstr "Prusa i3 MK2.5 gotowa"
 
+# 
+#:
+msgid "Prusa i3 MK3 OK."
+msgstr "Prusa i3 MK3 OK"
+
 # WELCOME_MSG c=20
 #:
 msgid "Prusa i3 MK3 ready."
@@ -1523,17 +1783,17 @@ msgid "Prusa i3 MK3S OK."
 msgstr "Prusa i3 MK3S OK"
 
 # MSG_PRUSA3D
-#: ultralcd.cpp:2227
+#: ultralcd.cpp:2098
 msgid "prusa3d.com"
 msgstr "prusa3d.com"
 
 # MSG_BED_CORRECTION_REAR c=14 r=1
-#: ultralcd.cpp:3102
+#: ultralcd.cpp:3218
 msgid "Rear side [um]"
 msgstr "Tyl [um]"
 
 # MSG_RECOVERING_PRINT c=20 r=1
-#: Marlin_main.cpp:8575
+#: Marlin_main.cpp:9712
 msgid "Recovering print    "
 msgstr "Wznawianie wydruku"
 
@@ -1543,10 +1803,15 @@ msgid "Refresh"
 msgstr "Odswiez"
 
 # MSG_REMOVE_OLD_FILAMENT c=20 r=4
-#: mmu.cpp:744
+#: mmu.cpp:830
 msgid "Remove old filament and press the knob to start loading new filament."
 msgstr "Wyciagnij poprzedni filament i nacisnij pokretlo aby zaladowac nowy."
 
+# 
+#: ultralcd.cpp:6605
+msgid "Rename"
+msgstr "Zmien nazwe"
+
 # MSG_M119_REPORT
 #: Marlin_main.cpp:5297
 msgid "Reporting endstop status"
@@ -1563,32 +1828,32 @@ msgid "Resend: "
 msgstr "Wyslij ponownie:"
 
 # MSG_BED_CORRECTION_RESET
-#: ultralcd.cpp:3103
+#: ultralcd.cpp:3219
 msgid "Reset"
 msgstr "Reset"
 
 # MSG_CALIBRATE_BED_RESET
-#: ultralcd.cpp:5203
+#: ultralcd.cpp:5669
 msgid "Reset XYZ calibr."
 msgstr "Reset kalibr. XYZ"
 
 # MSG_RESUME_PRINT
-#: ultralcd.cpp:6033
+#: ultralcd.cpp:6664
 msgid "Resume print"
 msgstr "Wznowic wydruk"
 
 # MSG_RESUMING_PRINT c=20 r=1
-#: messages.c:69
+#: messages.c:73
 msgid "Resuming print"
 msgstr "Wznawianie druku"
 
 # 
-#: ultralcd.cpp:2862
+#: ultralcd.cpp:2968
 msgid "Right"
 msgstr "Prawa"
 
 # MSG_BED_CORRECTION_RIGHT c=14 r=1
-#: ultralcd.cpp:3100
+#: ultralcd.cpp:3216
 msgid "Right side[um]"
 msgstr "Prawo [um]"
 
@@ -1603,22 +1868,22 @@ msgid "Rotate knob until mark reaches extruder body. Click when done."
 msgstr "Obracaj pokretlo az znacznik zrowna sie z korpusem ekstrudera i potwierdz naciskajac pokretlo."
 
 # MSG_SECOND_SERIAL_ON c=17 r=1
-#: ultralcd.cpp:5119
+#: ultralcd.cpp:5587
 msgid "RPi port     [on]"
 msgstr "Port RPi     [wl]"
 
 # MSG_SECOND_SERIAL_OFF c=17 r=1
-#: ultralcd.cpp:5117
+#: ultralcd.cpp:5585
 msgid "RPi port    [off]"
 msgstr "Port RPi    [wyl]"
 
 # MSG_WIZARD_RERUN c=20 r=7
-#: ultralcd.cpp:4583
+#: ultralcd.cpp:4723
 msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
 msgstr "Wlaczenie Asystenta usunie obecne dane kalibracyjne i zacznie od poczatku. Kontynuowac?"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_OFF c=19 r=1
-#: ultralcd.cpp:5033
+#: ultralcd.cpp:5220
 msgid "SD card  [normal]"
 msgstr "Karta SD [normal]"
 
@@ -1633,7 +1898,7 @@ msgid "SD card [FlshAir]"
 msgstr "Karta SD [FlashAir]"
 
 # MSG_TOSHIBA_FLASH_AIR_COMPATIBILITY_ON c=19 r=1
-#: ultralcd.cpp:5031
+#: ultralcd.cpp:5218
 msgid "SD card [flshAir]"
 msgstr "Karta SD[FlshAir]"
 
@@ -1652,53 +1917,63 @@ msgstr "SD printing byte "
 msgid "Searching bed calibration point"
 msgstr "Szukam punktu kalibracyjnego na stole"
 
+# 
+#: ultralcd.cpp:6601
+msgid "Select"
+msgstr "Wybierz"
+
 # MSG_LANGUAGE_SELECT
-#: ultralcd.cpp:5126
+#: ultralcd.cpp:5594
 msgid "Select language"
 msgstr "Wybor jezyka"
 
 # 
-#: ultralcd.cpp:4803
+#: ultralcd.cpp:4943
 msgid "Select nozzle preheat temperature which matches your material."
 msgstr "Wybierz temperature grzania dyszy odpowiednia dla materialu."
 
 # 
-#: ultralcd.cpp:4552
+#: ultralcd.cpp:4692
 msgid "Select PLA filament:"
 msgstr "Wybierz filament PLA:"
 
 # MSG_SELFTEST_OK
-#: ultralcd.cpp:6631
+#: ultralcd.cpp:7366
 msgid "Self test OK"
 msgstr "Selftest OK"
 
 # MSG_SELFTEST_START c=20
-#: ultralcd.cpp:6449
+#: ultralcd.cpp:7152
 msgid "Self test start  "
 msgstr "Rozpoczynanie Selftestu"
 
 # MSG_SELFTEST
-#: ultralcd.cpp:5179
+#: ultralcd.cpp:5645
 msgid "Selftest         "
 msgstr "Selftest "
 
 # MSG_SELFTEST_ERROR
-#: ultralcd.cpp:7058
+#: ultralcd.cpp:7793
 msgid "Selftest error !"
 msgstr "Blad selftest !"
 
 # MSG_SELFTEST_FAILED c=20
-#: messages.c:73
+#: messages.c:77
 msgid "Selftest failed  "
 msgstr "Selftest nieudany"
 
 # MSG_FORCE_SELFTEST c=20 r=8
-#: Marlin_main.cpp:1548
+#: Marlin_main.cpp:1567
 msgid "Selftest will be run to calibrate accurate sensorless rehoming."
 msgstr "Zostanie uruchomiony Selftest aby dokladnie skalibrowac punkt bazowy bez krancowek"
 
 # 
-#: ultralcd.cpp:3819
+#: ultralcd.cpp:2138
+msgid "Sensor info"
+msgstr "Info o sensorach"
+
+# 
+#: ultralcd.cpp:3938
 msgid "Sensor state"
 msgstr "Stan czujnikow"
 
@@ -1708,17 +1983,17 @@ msgid "Sensors info"
 msgstr "Info o czujnikach"
 
 # MSG_SET_TEMPERATURE c=19 r=1
-#: ultralcd.cpp:3111
+#: ultralcd.cpp:3227
 msgid "Set temperature:"
 msgstr "Ustaw. temperatury:"
 
 # MSG_SETTINGS
-#: messages.c:81
+#: messages.c:86
 msgid "Settings"
 msgstr "Ustawienia"
 
 # 
-#: ultralcd.cpp:2899
+#: ultralcd.cpp:3005
 msgid "Severe skew"
 msgstr "Znaczny skos"
 
@@ -1727,8 +2002,13 @@ msgstr "Znaczny skos"
 msgid "Severe skew:"
 msgstr "Powazny skos:"
 
+# 
+#: messages.c:58
+msgid "Sheet"
+msgstr "Plyta"
+
 # MSG_SHOW_END_STOPS c=17 r=1
-#: ultralcd.cpp:5200
+#: ultralcd.cpp:5666
 msgid "Show end stops"
 msgstr "Pokaz krancowki"
 
@@ -1743,7 +2023,7 @@ msgid "Sleep..."
 msgstr "Czuwanie..."
 
 # 
-#: ultralcd.cpp:2898
+#: ultralcd.cpp:3004
 msgid "Slight skew"
 msgstr "Lekki skos"
 
@@ -1753,15 +2033,30 @@ msgid "Slight skew:"
 msgstr "Lekki skos:"
 
 # MSG_FILE_CNT c=20 r=4
-#: cardreader.cpp:738
+#: cardreader.cpp:739
 msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
 msgstr "Niektore pliki nie zostana posortowane. Max. liczba plikow w 1 folderze = 100."
 
 # 
-#: Marlin_main.cpp:4560
+#: Marlin_main.cpp:4833
 msgid "Some problem encountered, Z-leveling enforced ..."
 msgstr "Wykryto problem, wymuszono poziomowanie osi Z ..."
 
+# MSG_SORT_NONE c=17 r=1
+#: ultralcd.cpp:5230
+msgid "Sort       [none]"
+msgstr "Sortowanie [brak]"
+
+# MSG_SORT_TIME c=17 r=1
+#: ultralcd.cpp:5228
+msgid "Sort       [time]"
+msgstr "Sortowanie [czas]"
+
+# MSG_SORT_ALPHA c=17 r=1
+#: ultralcd.cpp:5229
+msgid "Sort   [alphabet]"
+msgstr "Sort. [alfabet]"
+
 # MSG_SORT_NONE c=17 r=1
 #: ultralcd.cpp:4250
 msgid "Sort:      [None]"
@@ -1803,117 +2098,132 @@ msgid "Sort:  [time]"
 msgstr "Sortuj: [czas]"
 
 # MSG_SORTING c=20 r=1
-#: cardreader.cpp:745
+#: cardreader.cpp:746
 msgid "Sorting files"
 msgstr "Sortowanie plikow"
 
 # MSG_SOUND_LOUD c=17 r=1
-#: sound.h:5
+#: sound.h:6
 msgid "Sound      [loud]"
 msgstr "Dzwiek   [Glosny]"
 
 # MSG_SOUND_MUTE c=17 r=1
-#: sound.h:8
+#:
 msgid "Sound      [mute]"
 msgstr "Dzwiek[Wylaczony]"
 
 # MSG_SOUND_ONCE c=17 r=1
-#: sound.h:6
+#: sound.h:7
 msgid "Sound      [once]"
 msgstr "Dzwiek    [1-raz]"
 
+# 
+#:
+msgid "Sound     [assist]"
+msgstr "Dzwiek [asyst.]"
+
+# 
+#: sound.h:9
+msgid "Sound     [blind]"
+msgstr "Dzwiek[niewidomy]"
+
 # MSG_SOUND_SILENT c=17 r=1
-#: sound.h:7
+#: sound.h:8
 msgid "Sound    [silent]"
 msgstr "Dzwiek    [Cichy]"
 
 # MSG_SPEED
-#: ultralcd.cpp:6199
+#: ultralcd.cpp:6840
 msgid "Speed"
 msgstr "Predkosc"
 
 # MSG_SELFTEST_FAN_YES c=19
-#: messages.c:76
+#: messages.c:80
 msgid "Spinning"
 msgstr "Kreci sie"
 
 # MSG_AUTO_DEPLETE_ON c=17 r=1
-#: ultralcd.cpp:4959
+#: ultralcd.cpp:5098
 msgid "SpoolJoin    [on]"
 msgstr "SpoolJoin    [wl]"
 
 # 
-#: ultralcd.cpp:4955
+#: ultralcd.cpp:5094
 msgid "SpoolJoin   [N/A]"
 msgstr "SpoolJoin    [nd]"
 
 # MSG_AUTO_DEPLETE_OFF c=17 r=1
-#: ultralcd.cpp:4963
+#: ultralcd.cpp:5102
 msgid "SpoolJoin   [off]"
 msgstr "SpoolJoin   [wyl]"
 
 # MSG_TEMP_CAL_WARNING c=20 r=4
-#: Marlin_main.cpp:4065
+#: Marlin_main.cpp:4330
 msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
 msgstr "Potrzebna jest stabilna temperatura otoczenia 21-26C i stabilne podloze."
 
 # MSG_STATISTICS
-#: ultralcd.cpp:6108
+#: ultralcd.cpp:6753
 msgid "Statistics  "
 msgstr "Statystyki"
 
+# 
+#: ultralcd.cpp:5551
+msgid "Steel sheets"
+msgstr "Plyty stalowe"
+
 # MSG_STEPPER_TOO_HIGH
 #: stepper.cpp:345
 msgid "Steprate too high: "
 msgstr "Liczba krokow zbyt wysoka:"
 
 # MSG_STOP_PRINT
-#: messages.c:87
+#: messages.c:93
 msgid "Stop print"
-msgstr "Zatrzymac druk"
+msgstr "Przerwanie druku"
 
 # MSG_STOPPED
-#: messages.c:88
+#: messages.c:94
 msgid "STOPPED. "
 msgstr "ZATRZYMANO."
 
 # MSG_SUPPORT
-#: ultralcd.cpp:6117
+#: ultralcd.cpp:6762
 msgid "Support"
 msgstr "Wsparcie"
 
 # MSG_SELFTEST_SWAPPED
-#: ultralcd.cpp:7138
+#: ultralcd.cpp:7873
 msgid "Swapped"
 msgstr "Zamieniono"
 
 # MSG_TEMP_CALIBRATION c=20 r=1
-#: messages.c:89
+#: messages.c:95
 msgid "Temp. cal.          "
 msgstr "Kalibracja temp."
 
 # MSG_TEMP_CALIBRATION_ON c=20 r=1
-#: ultralcd.cpp:5113
+#: ultralcd.cpp:5581
 msgid "Temp. cal.   [on]"
 msgstr "Kalibr. temp.[wl]"
 
 # MSG_TEMP_CALIBRATION_OFF c=20 r=1
-#: ultralcd.cpp:5111
+#: ultralcd.cpp:5579
 msgid "Temp. cal.  [off]"
 msgstr "Kalibr.temp.[wyl]"
 
 # MSG_CALIBRATION_PINDA_MENU c=17 r=1
-#: ultralcd.cpp:5209
+#: ultralcd.cpp:5675
 msgid "Temp. calibration"
 msgstr "Kalibracja temp."
 
 # MSG_TEMPERATURE
-#: ultralcd.cpp:5089
+#: ultralcd.cpp:5548
 msgid "Temperature"
 msgstr "Temperatura"
 
 # MSG_TEMP_CAL_FAILED c=20 r=8
-#: ultralcd.cpp:3744
+#: ultralcd.cpp:3864
 msgid "Temperature calibration failed"
 msgstr "Kalibracja temperaturowa nieudana"
 
@@ -1923,12 +2233,12 @@ msgid "Temperature calibration has not been run yet"
 msgstr "Kalibracja temperaturowa nie zostala jeszcze przeprowadzona"
 
 # MSG_TEMP_CALIBRATION_DONE c=20 r=12
-#: messages.c:90
+#: messages.c:96
 msgid "Temperature calibration is finished and active. Temp. calibration can be disabled in menu Settings->Temp. cal."
 msgstr "Kalibracja temperaturowa zakonczona i wlaczona. Moze byc wylaczona z menu Ustawienia -> Kalibracja temp."
 
 # MSG_MENU_TEMPERATURES c=15 r=1
-#: ultralcd.cpp:2273
+#: ultralcd.cpp:2144
 msgid "Temperatures"
 msgstr "Temperatury"
 
@@ -1938,27 +2248,27 @@ msgid "There is still a need to make Z calibration. Please follow the manual, ch
 msgstr "Musimy przeprowadzic kalibracje Z. Kieruj sie Samouczkiem: rozdzial Pierwsze Kroki, sekcja Kalibracja."
 
 # 
-#: ultralcd.cpp:2316
+#: ultralcd.cpp:2217
 msgid "to load filament"
 msgstr "aby zaladow. fil."
 
 # 
-#: ultralcd.cpp:2317
+#: ultralcd.cpp:2221
 msgid "to unload filament"
 msgstr "aby rozlad. filament"
 
 # 
-#: ultralcd.cpp:1961
+#: ultralcd.cpp:1829
 msgid "Total"
 msgstr "Suma"
 
 # 
-#: ultralcd.cpp:1994
+#: ultralcd.cpp:1862
 msgid "Total failures"
 msgstr "Suma bledow"
 
 # 
-#: ultralcd.cpp:2752
+#: ultralcd.cpp:2860
 msgid "Total filament"
 msgstr "Calkowita dlugosc filamentu"
 
@@ -1968,7 +2278,7 @@ msgid "Total filament :"
 msgstr "Filament lacznie :"
 
 # 
-#: ultralcd.cpp:2754
+#: ultralcd.cpp:2860
 msgid "Total print time"
 msgstr "Calkowity czas druku"
 
@@ -1983,17 +2293,17 @@ msgid "TRIGGERED"
 msgstr "AKTYWOWANO"
 
 # MSG_TUNE
-#: ultralcd.cpp:6015
+#: ultralcd.cpp:6641
 msgid "Tune"
 msgstr "Strojenie"
 
 # 
-#: ultralcd.cpp:2249
+#: ultralcd.cpp:2120
 msgid "unknown"
 msgstr "nieznane"
 
 # 
-#: ultralcd.cpp:4640
+#: ultralcd.cpp:4780
 msgid "Unload"
 msgstr "Rozladuj"
 
@@ -2003,7 +2313,7 @@ msgid "Unload all"
 msgstr "Rozladuj wszystkie"
 
 # MSG_UNLOAD_FILAMENT c=17
-#: messages.c:91
+#: messages.c:97
 msgid "Unload filament"
 msgstr "Rozladowanie fil."
 
@@ -2028,22 +2338,22 @@ msgid "Unload filament 4"
 msgstr "Rozladuj fil. 4"
 
 # MSG_UNLOADING_FILAMENT c=20 r=1
-#: messages.c:92
+#: messages.c:98
 msgid "Unloading filament"
 msgstr "Rozladowuje filament"
 
 # 
-#: ultralcd.cpp:4639
+#: ultralcd.cpp:4779
 msgid "Use unload to remove filament 1 if it protrudes outside of the rear MMU tube. Use eject if it is hidden in tube."
 msgstr "Uzyj opcji Rozladuj jesli filament wystaje z tylnej rurki MMU. Uzyj opcji Wysun jesli wciaz jest w srodku."
 
 # MSG_USED c=19 r=1
-#: ultralcd.cpp:5334
+#: ultralcd.cpp:5803
 msgid "Used during print"
 msgstr "Uzyte podczas druku"
 
 # MSG_MENU_VOLTAGES c=15 r=1
-#: ultralcd.cpp:2276
+#: ultralcd.cpp:2147
 msgid "Voltages"
 msgstr "Napiecia"
 
@@ -2053,32 +2363,37 @@ msgid "volume.init failed"
 msgstr "niepowodzenie volume.init "
 
 # MSG_USERWAIT
-#: Marlin_main.cpp:4876
+#: Marlin_main.cpp:5225
 msgid "Wait for user..."
 msgstr "Czekam na uzytkownika..."
 
 # MSG_WAITING_TEMP c=20 r=3
-#: ultralcd.cpp:3255
+#: ultralcd.cpp:3371
 msgid "Waiting for nozzle and bed cooling"
 msgstr "Oczekiwanie na wychlodzenie dyszy i stolu"
 
 # MSG_WAITING_TEMP_PINDA c=20 r=3
-#: ultralcd.cpp:3219
+#: ultralcd.cpp:3335
 msgid "Waiting for PINDA probe cooling"
 msgstr "Czekam az spadnie temp. sondy PINDA"
 
+# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
+#:
+msgid "WARNING:\nCrash detection\ndisabled in\nStealth mode"
+msgstr "UWAGA:\nWykrywanie zderzen\nwylaczone\nw trybie Stealth"
+
 # MSG_CHANGED_BOTH c=20 r=4
-#: Marlin_main.cpp:1508
+#: Marlin_main.cpp:1527
 msgid "Warning: both printer type and motherboard type changed."
 msgstr "Ostrzezenie: typ drukarki i plyta glowna ulegly zmianie."
 
 # MSG_CHANGED_MOTHERBOARD c=20 r=4
-#: Marlin_main.cpp:1500
+#: Marlin_main.cpp:1519
 msgid "Warning: motherboard type changed."
 msgstr "Ostrzezenie: plyta glowna ulegla zmianie."
 
 # MSG_CHANGED_PRINTER c=20 r=4
-#: Marlin_main.cpp:1504
+#: Marlin_main.cpp:1523
 msgid "Warning: printer type changed."
 msgstr "Ostrzezenie: rodzaj drukarki ulegl zmianie"
 
@@ -2088,17 +2403,17 @@ msgid "WARNING: This is an unofficial, unsupported build. Use at your own risk!"
 msgstr "OSTRZEZENIE: To jest nieoficjalna, niewspierana wersja firmware. Uzywasz na wlasna odpowiedzialnosc!"
 
 # MSG_UNLOAD_SUCCESSFUL c=20 r=2
-#: Marlin_main.cpp:3014
+#: Marlin_main.cpp:3072
 msgid "Was filament unload successful?"
 msgstr "Rozladowanie fil. ok?"
 
 # MSG_SELFTEST_WIRINGERROR
-#: messages.c:80
+#: messages.c:85
 msgid "Wiring error"
 msgstr "Blad polaczenia"
 
 # MSG_WIZARD c=17 r=1
-#: ultralcd.cpp:5176
+#: ultralcd.cpp:5642
 msgid "Wizard"
 msgstr "Asystent"
 
@@ -2117,23 +2432,28 @@ msgstr "Zapis do pliku:"
 msgid "X-correct"
 msgstr "Korekcja X"
 
+# 
+#: ultralcd.cpp:5028
+msgid "X-correct:"
+msgstr "Korekcja-X:"
+
 # MSG_XYZ_DETAILS c=19 r=1
-#: ultralcd.cpp:2265
+#: ultralcd.cpp:2136
 msgid "XYZ cal. details"
 msgstr "Szczegoly kal. XYZ"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
-#: ultralcd.cpp:3715
+#: ultralcd.cpp:3835
 msgid "XYZ calibration all right. Skew will be corrected automatically."
 msgstr "Kalibracja XYZ pomyslna. Skos bedzie automatycznie korygowany."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
-#: ultralcd.cpp:3712
+#: ultralcd.cpp:3832
 msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
 msgstr "Kalibracja XYZ prawidlowa. Osie X/Y lekko skosne. Dobra robota!"
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
-#: ultralcd.cpp:3693
+#: ultralcd.cpp:3813
 msgid "XYZ calibration compromised. Front calibration points not reachable."
 msgstr "Kalibr. XYZ niedokladna. Przednie punkty kalibr. nieosiagalne."
 
@@ -2143,17 +2463,17 @@ msgid "XYZ calibration compromised. Left front calibration point not reachable."
 msgstr "Kalibracja XYZ niedokladna. Lewy przedni punkt nieosiagalny."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
-#: ultralcd.cpp:3696
+#: ultralcd.cpp:3816
 msgid "XYZ calibration compromised. Right front calibration point not reachable."
 msgstr "Kalibracja XYZ niedokladna. Prawy przedni punkt nieosiagalny."
 
 # 
-#: ultralcd.cpp:3675
+#: ultralcd.cpp:3795
 msgid "XYZ calibration failed. Bed calibration point was not found."
 msgstr "Kalibracja XYZ nieudana. Nie znaleziono punktow kalibracyjnych."
 
 # 
-#: ultralcd.cpp:3681
+#: ultralcd.cpp:3801
 msgid "XYZ calibration failed. Front calibration points not reachable."
 msgstr "Kalibr. XYZ nieudana. Przednie punkty kalibr. nieosiagalne. Nalezy poprawic montaz drukarki."
 
@@ -2168,17 +2488,17 @@ msgid "XYZ calibration failed. Please consult the manual."
 msgstr "Kalibracja XYZ nieudana. Sprawdz przyczyny i rozwiazania w instrukcji."
 
 # 
-#: ultralcd.cpp:3684
+#: ultralcd.cpp:3804
 msgid "XYZ calibration failed. Right front calibration point not reachable."
 msgstr "Kalibr. XYZ nieudana. Prawy przedni punkt nieosiagalny. Nalezy poprawic montaz drukarki."
 
 # MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
-#: ultralcd.cpp:3709
+#: ultralcd.cpp:3829
 msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
 msgstr "Kalibracja XYZ ok. Osie X/Y sa prostopadle. Gratulacje!"
 
 # 
-#: ultralcd.cpp:2859
+#: ultralcd.cpp:2965
 msgid "Y distance from min"
 msgstr "Dystans od 0 w osi Y"
 
@@ -2192,8 +2512,13 @@ msgstr "Min. odleglosc od Y:"
 msgid "Y-correct"
 msgstr "Korekcja Y"
 
+# 
+#: ultralcd.cpp:5029
+msgid "Y-correct:"
+msgstr "Korekcja-Y:"
+
 # MSG_YES
-#: messages.c:98
+#: messages.c:104
 msgid "Yes"
 msgstr "Tak"
 
@@ -2208,11 +2533,26 @@ msgid "You are using firmware beta version. This is development version. Using t
 msgstr "Uzywasz firmware w wersji beta. Ta wersja jest rozwojowa. Uzywanie jej nie jest zalecane i moze spowodowac uszkodzenie drukarki."
 
 # MSG_WIZARD_QUIT c=20 r=8
-#: messages.c:97
+#: messages.c:103
 msgid "You can always resume the Wizard from Calibration -> Wizard."
 msgstr "Zawsze mozesz uruchomic Asystenta ponownie przez Kalibracja -> Asystent."
 
+# 
+#: ultralcd.cpp:5030
+msgid "Z-correct:"
+msgstr "Korekcja-Z:"
+
+# 
+#: ultralcd.cpp:6952
+msgid "Z-probe nr.    [1]"
+msgstr "Pomiar-Z [1]"
+
+# 
+#: ultralcd.cpp:6954
+msgid "Z-probe nr.    [3]"
+msgstr "Pomiar-Z [3]"
+
 # MSG_MEASURED_OFFSET
-#: ultralcd.cpp:2914
+#: ultralcd.cpp:3024
 msgid "[0;0] point offset"
 msgstr "[0;0] przesuniecie punktu"