 PavelSindler
|
e5d10074cf
stop print during auto home and mesh bed leveling improved
|
8 tahun lalu |
|
PavelSindler
|
12f9afce74
tset heatbed target temperature to zero at the end of temp. calibration, before final message is shown
|
8 tahun lalu |
|
PavelSindler
|
8f904f90d0
Italian bed correction messages corrected
|
8 tahun lalu |
|
PavelSindler
|
fefa240cd7
czech messages corrected; temp. calibration: improved serial communication, disable steppers after calibration, preheat phase on start print when running from octoprint,
|
8 tahun lalu |
|
PavelSindler
|
57ef9cf59b
unloading filaments and M600 messages updated
|
8 tahun lalu |
|
PavelSindler
|
bb3887fe1b
calibration status and pinda probe calibration status were split
|
8 tahun lalu |
|
PavelSindler
|
9fdd23aaa5
snmm: czech messages corrected, M600 filament not loaded, timers updated, updated behavior when choosing "change filament" from menu
|
8 tahun lalu |
|
PavelSindler
|
134a50f5b3
messages updated, different bowden lengths for SNMM used, M600 for SNMM updated, stop print for SNMM updated, load all filaments added
|
8 tahun lalu |
|
PavelSindler
|
df9f063f99
snmm: removed detection if print was terminated by reset/blackout; initial version of stop print for snmm
|
8 tahun lalu |
|
PavelSindler
|
2fa97d5dfe
Added messages in czech and english for SNMM, service menu for adjusting bowden lengths; updated service menu to be extendable; M600: loading filament for SNMM updated; unload all filaments updated
|
8 tahun lalu |
|
PavelSindler
|
032f2637a7
adding edits made by akukan
|
8 tahun lalu |
|
PavelSindler
|
32df4f68a1
messages translated, invalidate calibration status at the beginning of temp. calibration
|
8 tahun lalu |
|
PavelSindler
|
397039270a
PINDA Preheating countdown updated
|
8 tahun lalu |
|
PavelSindler
|
50b7f627cd
pinda preheating messages changed
|
8 tahun lalu |
|
PavelSindler
|
7e8780ba61
long press compatible with timeout to status, temp compensation extrapolation, preheat Z coordinate added, G75 for showing interpolation table
|
8 tahun lalu |
|
PavelSindler
|
7ec45271c2
timeout to status, better print time counting when using pause print
|
8 tahun lalu |
|
PavelSindler
|
c03a18f8c3
czech messages added, temperature calibration is off in fresh eeprom, pinda preheat phase is not used unless calibration was run, pause print works with gcode absolute and relative extruder mode, move z higher after selftest
|
8 tahun lalu |
|
PavelSindler
|
329e1ac9bb
waiting for PINDA to cool down
|
8 tahun lalu |
|
PavelSindler
|
4de9b1c9f6
temp calibration on/off initialization when updating firmware
|
8 tahun lalu |
|
PavelSindler
|
70b6e13de4
farm mode activation and farm number initialization handled when upgrading firmware versions and when flashing to new eeprom
|
8 tahun lalu |
|
PavelSindler
|
e061209fc2
mesh bed leveling flag
|
8 tahun lalu |
|
PavelSindler
|
ba36fbbfa3
endif removed
|
8 tahun lalu |
|
PavelSindler
|
fc221fbea5
Merged PINDA temp calibration branch into MK2
|
8 tahun lalu |
|
PavelSindler
|
7b962d666f
pause print statistics
|
8 tahun lalu |
|
PavelSindler
|
2060d319f5
faster load filament, extrusion before unload filament
|
8 tahun lalu |
|
PavelSindler
|
fab71ff7cf
information that temp calibration active is active is stored to eeprom
|
8 tahun lalu |
|
PavelSindler
|
ccdf5e9c41
Message that temp calibration has not been run yet is displayed only if temp. calibration is activated
|
8 tahun lalu |
|
PavelSindler
|
08a59f7fef
status messages for temp calibration added, initial versoin of temp calibration on/off from menu
|
8 tahun lalu |
|
PavelSindler
|
abadaa5885
added retraction to preheat, no waiting when running mesh bed leveling from calibration menu
|
8 tahun lalu |
|
PavelSindler
|
762167fb00
Merge remote-tracking branch 'ayourk/MK2' into MK2
|
8 tahun lalu |
