 PavelSindler
|
e5d10074cf
stop print during auto home and mesh bed leveling improved
|
8 лет назад |
|
PavelSindler
|
12f9afce74
tset heatbed target temperature to zero at the end of temp. calibration, before final message is shown
|
8 лет назад |
|
PavelSindler
|
8f904f90d0
Italian bed correction messages corrected
|
8 лет назад |
|
PavelSindler
|
fefa240cd7
czech messages corrected; temp. calibration: improved serial communication, disable steppers after calibration, preheat phase on start print when running from octoprint,
|
8 лет назад |
|
PavelSindler
|
57ef9cf59b
unloading filaments and M600 messages updated
|
8 лет назад |
|
PavelSindler
|
bb3887fe1b
calibration status and pinda probe calibration status were split
|
8 лет назад |
|
PavelSindler
|
9fdd23aaa5
snmm: czech messages corrected, M600 filament not loaded, timers updated, updated behavior when choosing "change filament" from menu
|
8 лет назад |
|
PavelSindler
|
134a50f5b3
messages updated, different bowden lengths for SNMM used, M600 for SNMM updated, stop print for SNMM updated, load all filaments added
|
8 лет назад |
|
PavelSindler
|
df9f063f99
snmm: removed detection if print was terminated by reset/blackout; initial version of stop print for snmm
|
8 лет назад |
|
PavelSindler
|
2fa97d5dfe
Added messages in czech and english for SNMM, service menu for adjusting bowden lengths; updated service menu to be extendable; M600: loading filament for SNMM updated; unload all filaments updated
|
8 лет назад |
|
PavelSindler
|
032f2637a7
adding edits made by akukan
|
8 лет назад |
|
PavelSindler
|
32df4f68a1
messages translated, invalidate calibration status at the beginning of temp. calibration
|
8 лет назад |
|
PavelSindler
|
397039270a
PINDA Preheating countdown updated
|
8 лет назад |
|
PavelSindler
|
50b7f627cd
pinda preheating messages changed
|
8 лет назад |
|
PavelSindler
|
7e8780ba61
long press compatible with timeout to status, temp compensation extrapolation, preheat Z coordinate added, G75 for showing interpolation table
|
8 лет назад |
|
PavelSindler
|
7ec45271c2
timeout to status, better print time counting when using pause print
|
8 лет назад |
|
PavelSindler
|
c03a18f8c3
czech messages added, temperature calibration is off in fresh eeprom, pinda preheat phase is not used unless calibration was run, pause print works with gcode absolute and relative extruder mode, move z higher after selftest
|
8 лет назад |
|
PavelSindler
|
329e1ac9bb
waiting for PINDA to cool down
|
8 лет назад |
|
PavelSindler
|
4de9b1c9f6
temp calibration on/off initialization when updating firmware
|
8 лет назад |
|
PavelSindler
|
70b6e13de4
farm mode activation and farm number initialization handled when upgrading firmware versions and when flashing to new eeprom
|
8 лет назад |
|
PavelSindler
|
e061209fc2
mesh bed leveling flag
|
8 лет назад |
|
PavelSindler
|
ba36fbbfa3
endif removed
|
8 лет назад |
|
PavelSindler
|
fc221fbea5
Merged PINDA temp calibration branch into MK2
|
8 лет назад |
|
PavelSindler
|
7b962d666f
pause print statistics
|
8 лет назад |
|
PavelSindler
|
2060d319f5
faster load filament, extrusion before unload filament
|
8 лет назад |
|
PavelSindler
|
fab71ff7cf
information that temp calibration active is active is stored to eeprom
|
8 лет назад |
|
PavelSindler
|
ccdf5e9c41
Message that temp calibration has not been run yet is displayed only if temp. calibration is activated
|
8 лет назад |
|
PavelSindler
|
08a59f7fef
status messages for temp calibration added, initial versoin of temp calibration on/off from menu
|
8 лет назад |
|
PavelSindler
|
abadaa5885
added retraction to preheat, no waiting when running mesh bed leveling from calibration menu
|
8 лет назад |
|
PavelSindler
|
762167fb00
Merge remote-tracking branch 'ayourk/MK2' into MK2
|
8 лет назад |
