 PavelSindler
|
e5d10074cf
stop print during auto home and mesh bed leveling improved
|
8 anni fa |
|
PavelSindler
|
12f9afce74
tset heatbed target temperature to zero at the end of temp. calibration, before final message is shown
|
8 anni fa |
|
PavelSindler
|
8f904f90d0
Italian bed correction messages corrected
|
8 anni fa |
|
PavelSindler
|
fefa240cd7
czech messages corrected; temp. calibration: improved serial communication, disable steppers after calibration, preheat phase on start print when running from octoprint,
|
8 anni fa |
|
PavelSindler
|
57ef9cf59b
unloading filaments and M600 messages updated
|
8 anni fa |
|
PavelSindler
|
bb3887fe1b
calibration status and pinda probe calibration status were split
|
8 anni fa |
|
PavelSindler
|
9fdd23aaa5
snmm: czech messages corrected, M600 filament not loaded, timers updated, updated behavior when choosing "change filament" from menu
|
8 anni fa |
|
PavelSindler
|
134a50f5b3
messages updated, different bowden lengths for SNMM used, M600 for SNMM updated, stop print for SNMM updated, load all filaments added
|
8 anni fa |
|
PavelSindler
|
df9f063f99
snmm: removed detection if print was terminated by reset/blackout; initial version of stop print for snmm
|
8 anni fa |
|
PavelSindler
|
2fa97d5dfe
Added messages in czech and english for SNMM, service menu for adjusting bowden lengths; updated service menu to be extendable; M600: loading filament for SNMM updated; unload all filaments updated
|
8 anni fa |
|
PavelSindler
|
032f2637a7
adding edits made by akukan
|
8 anni fa |
|
PavelSindler
|
32df4f68a1
messages translated, invalidate calibration status at the beginning of temp. calibration
|
8 anni fa |
|
PavelSindler
|
397039270a
PINDA Preheating countdown updated
|
8 anni fa |
|
PavelSindler
|
50b7f627cd
pinda preheating messages changed
|
8 anni fa |
|
PavelSindler
|
7e8780ba61
long press compatible with timeout to status, temp compensation extrapolation, preheat Z coordinate added, G75 for showing interpolation table
|
8 anni fa |
|
PavelSindler
|
7ec45271c2
timeout to status, better print time counting when using pause print
|
8 anni fa |
|
PavelSindler
|
c03a18f8c3
czech messages added, temperature calibration is off in fresh eeprom, pinda preheat phase is not used unless calibration was run, pause print works with gcode absolute and relative extruder mode, move z higher after selftest
|
8 anni fa |
|
PavelSindler
|
329e1ac9bb
waiting for PINDA to cool down
|
8 anni fa |
|
PavelSindler
|
4de9b1c9f6
temp calibration on/off initialization when updating firmware
|
8 anni fa |
|
PavelSindler
|
70b6e13de4
farm mode activation and farm number initialization handled when upgrading firmware versions and when flashing to new eeprom
|
8 anni fa |
|
PavelSindler
|
e061209fc2
mesh bed leveling flag
|
8 anni fa |
|
PavelSindler
|
ba36fbbfa3
endif removed
|
8 anni fa |
|
PavelSindler
|
fc221fbea5
Merged PINDA temp calibration branch into MK2
|
8 anni fa |
|
PavelSindler
|
7b962d666f
pause print statistics
|
8 anni fa |
|
PavelSindler
|
2060d319f5
faster load filament, extrusion before unload filament
|
8 anni fa |
|
PavelSindler
|
fab71ff7cf
information that temp calibration active is active is stored to eeprom
|
8 anni fa |
|
PavelSindler
|
ccdf5e9c41
Message that temp calibration has not been run yet is displayed only if temp. calibration is activated
|
8 anni fa |
|
PavelSindler
|
08a59f7fef
status messages for temp calibration added, initial versoin of temp calibration on/off from menu
|
8 anni fa |
|
PavelSindler
|
abadaa5885
added retraction to preheat, no waiting when running mesh bed leveling from calibration menu
|
8 anni fa |
|
PavelSindler
|
762167fb00
Merge remote-tracking branch 'ayourk/MK2' into MK2
|
8 anni fa |
